TRASH COMPACTOR
SERVICE MANUAL
MODEL
1052-B
MODELS
1050-J & 1051-J
only
Broan-NuTone LLC,
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
Condition
Possible Cause
Correction
Special Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
Condition
Possible Cause
Correction
Special Notes
Download from Www.Somanuals.com. All Manuals Search And Download.
CABINET REPLACEMENT - POWER
PACK REMOVAL
A box or similar stand approximately 11” high x 15” long x 7” wide
is recommended for power pack removal. The box must be able to
support 60 lbs. or more since you will be placing the full weight of
the power pack on it.
1. Unplug compactor from socket.
2. Remove drawer assembly from cabinet.
3. Remove Air Scentry tray and control panel.
DRAWER ASSEMBLY
1. Pull out drawer until it stops.
2. Lift drawer slightly, then pull out drawer to second stop.
3. Lift drawer up and out of compactor.
FOOT PEDAL (MODELS 1050 & 1051 ONLY)
1. Remove foot pedal retainers from each side of pedal.
2. Push foot pedal hinge pin out, catch foot pedal spring as it
comes free.
4. Remove key switch control bracket assembly. Remove back
panel.
5. Place box in cabinet and lower ram manually by turning 15/
16" nut on sprocket clockwise. Box should support weight of
power pack.
6. Remove the four 5/16" nuts supporting the power pack in the
cabinet.
DOOR LINER
Remove the door from the drawer by unlatching the door and
removing the hinge pins. The door liner can be removed from the
door by removing the toe space cover and all screws holding the
door liner to the door. Slide the door liner to side of door and lift
off. (Models 1050 and 1051 will require removal of the foot pedal
prior to toe space cover.)
7. Disconnect ground wire attached to cabinet.
8. Turn 15/16" nut counterclockwise causing power pack to lower
down out of cabinet. Pull power pack out through front of
rear of compactor.
DRAWER AND BASE ROLLERS
If you are replacing the cabinet, remove remaining parts from old
cabinet and install on new. See appropriate sections of service
manual.
Reverse procedure to install power pack. Be sure the weld strip,
grommets, and spacers are in place. The lock nuts should be
torqued to 5 ft./lbs. (60 inch/lbs.). Do not overtorque.
All four of the rollers are secured with a 1/2" hex nut and slotted
for screwdriver. Roller nuts are installed using LocktiteR and
torqued to 20 foot pounds. Rollers are pregreased and should
require no lubricant.
Be careful not to pinch or nick any wires when installing power
pack in cabinet.
BOTTOM ASSEMBLY
1. Unscrew level legs from base. Remove tee nuts that legs screw
into.
2. Remove screws securing bottom assembly to the cabinet.
3. Lower the bottom down into the cabinet, back end first, then
bring it up and out through the notches in the bottom flange
of the cabinet.
CONTROL PANEL
On units with a bag storage compartment, removal of the storage
compartment will make replacement of the control panel easier.
1. Remove drawer assembly.
2. Remove the four screws securing the air scentry tray and the
bottom of control panel to the cabinet.
3. Pull bottom of control panel out slightly and then up.
When installing the control panel, make sure lip on inside of
control panel snaps behind the bend in the control panel bracket.
STORAGE COMPARTMENT
Remove two screws on rear of compactor and the two 5/16" hex
head screws inside the storage compartment. Slide compartment
back and lift off.
Download from Www.Somanuals.com. All Manuals Search And Download.
SWITCH LOCATIONS
the door. Another switch located against the interlock switch is
the door. Another switch located against the interlock switch is
to provide the “No-Jam” circuitry function. This switch is nor-
mally open and bypasses the interlock to provide “No-Jam” ca-
pability. It can be replaced in the same manner as the interlock
switch.
TO REPLACE INTERLOCK SWITCH
1. Remove air scentry panel assembly.
2. Disconnect leads one by one and attach to new switch.
TRUNNION NUT
1. Remove back panel, drawer assembly and air scentry panel.
KEY SWITCH
1. Remove control panel.
2. Lower ram manually to approx. 10-1/2" from the bottom as-
sembly onto box or stand described in “CABINET REPLACE-
MENT/POWER PACK REMOVAL” section.
2. Remove two hex head screws supporting control panel bracket
with 5/16" socket.
3. Pull bracket out and remove switch.
3. Remove screws from nut retainer.
4. Raise ram assembly slightly by hand and remove nut.
NOTE: Count the number of revolutions to spin off nut. TRUN-
NION must be reinstalled to same position.
5. Reinstall trunnion nut and retainer.
CONTINUAL STRIPPING OF TRUNNION NUT:
POSSIBLE CAUSES:
1. Incorrect assembly of trunnion assembly.
2. Transporting compactor incorrectly.
3. Burr on main drive screw; sharp edge on lead-in thread.
4. Upper limit switch adjustment.
UPPER LIMIT SWITCH
1. Remove drawer assembly.
2. Lower ram to gain access to switch.
3. Remove air scentry tray.
4. Remove hex head screw with 5/16" socket, pull switch down
and disconnect wires.
REMOVING PLASTIC BAGS FROM
TRUNNION NUT
Only the trash compactor bags specifically designed and sold by
Broan for use in the compactor should be used. Regular plastic
garbage bags used in place of the Broan bags may be drawn into
the mechanism. Removal of those bags is not covered by the
warranty.
Check
Continuity
Switch not
Activated
Switch
Activated
3 to 1
2 to 1
6 to 1
3 to 4
6 to 4
5 to 7
closed
open
open
open
closed
open
open
closed
open
open
open
To remove bag from trunnion nut:
1. Remove back of compactor.
2. If possible to slide drawer slightly, remove the door by sliding
out the two hinge pins and then prying the door over the lip
on the drawer.
3. Liberally spray drive screw and trunnion nut with WD-40R or
similar.
closed
4. Use 15/16" socket, and extension, and a 16" ratchet (for lever-
age) and manually turn the drive screw clockwise. (See sec-
tion on manually raising and lowering ram.) By turning the
drive screw clockwise, you will help back the bag out of the
trunnion nut.
5. After removing bag, clean drive screw and regrease it with
wheel bearing grease.
DRIVE SCREW
1. Lower ram manually approximately halfway.
INTERLOCK SWITCH
The interlock switch is a single-pole, single-throw momentary
type. It is located on the right side behind the air scentry panel.
Its contacts are normally open. the contacts close when the door
is closed. It is activated by the actuator located on the back of
2. Remove sprocket.
3. Remove 1/4" drive pin. Slide off washers.
4. Lift ram, causing drive screw to slide out of the motor trun-
nion bearing. Support motor/gearbox assembly since it is now
free to pivot. Unscrew drive screw from front trunnion assem-
Download from Www.Somanuals.com. All Manubalyls. Search And Download.
TRUNNION BEARING
1. Remove sprocket and drive pin.
2. Pull out trunnion bearing.
GEARBOX
1. Lower ram manually until there is approximately 11" to 12"
between the ram and the bottom assembly.
2. Remove the four 3/8" nuts securing motor to gearbox, slide
motor out and rest it on the front trunnion assembly.
Grease trunnion bearing inside and out with wheel bearing grease
prior to reinstalling.
3. Turn sprocket until two holes in sprocket line up with the two
socket head cap screws that hold the gearbox to the motor
trunnion.
4. Remove the two socket head cap screws with a 5/32" hex key.
NOTE: The screws thread into 2 nuts which rest in slots in the
motor trunnion. Be careful not to lose the 2 nuts when the
screws are removed.
MOTOR TRUNNION
1. Remove motor, gearbox, spocket, and screw guard.
2. Use 13/16" wrench to remove bolts securing links to motor
trunnion.
When reinstalling, bolts should be torqued to 45 foot pounds.
5. Tilt gearbox forward and remove chain. Lift gearbox out.
When installing gearbox, Locktite® should be applied to the socket
head cap screw nuts.
SPROCKET
1. Line up one of the 3/8" holes in the sprocket with the 3/8"
hole in bottom center of gearbox. Insert 3/8" steel pin or bolt
through sprocket hole into front and rear gearbox holes.*
2. Loosen and remove 15/16" nut on the drive screw. When
reinstalling torque to 65 foot pounds and apply Locktite® to
threads.
*If the sprocket is
too damaged to be
able to use on of the
holes to secure it,
chip away the re-
maining sprocket, re-
move the drive pin
and then insert a
screwdriver through
the hole to provide a
means of keeping the
drive screw from
turning.
CHAIN
1. Turn sprocket until two holes in sprocket line up with socket
head cap screws.
2. Remove socket head cap screws and tip gearbox/motor as-
sembly to remove chain. NOTE: The screws thread into 2
nuts which rest in slots in the motor trunnion. Be careful not
to lose the 2 nuts when the screws are removed.
When reinstalling socket head cap screws, be sure Locktite® is
applied to the nuts.
Chain Derailment: Loose chains. Sometimes a chain will derail
because trash which flew up above the ram during compacting
fouled the chain. Newspaper or a paper bag should be placed on
top of glass bottles before compacting to prevent this.
If continual derailment of the chain is a problem, inspect both
sprockets for worn or missing
teeth. Inspect gearbox mount-
ing and mounting plate. If the
mounting screws are loose,
gearbox movement may be the
cause. If the gearbox mounting
plate is bent where it meets the
motor trunnion, either straight-
en or replace the gearbox.
Some chain looseness is nor-
mal and may increase as the
compactor is used. Seldom
does the chain “stretch” to the
point where it is too loose.
GREASING COMPACTOR
MECHANISM
1. Unplug compactor from wall outlet.
2. Remove drawer assembly from compactor.
3. Remove back of compactor and lower mechanism manually
by turning 15/16" nut on sprocket clockwise.
4. Line up one of the holes in the black sprocket with the hole in
the gearbox. Insert a 3/8" bolt or pin to keep sprocket from
turning and remove the 15/16" nut.
5. Slide off sprocket and washer.
6. Drive out the drive pin, slide off thin washer and pull out
trunnion bearing.
7. Grease trunnion bearing everywhere, inside and out, with
regular wheel bearing grease.
8. Reassemble unit in reverse procedure. When reinstalling 15/
16" nut, be sure to apply a drop of Locktite® or equivalent to
the threads of the 15/16" nut.
Apply grease to length of drive screw and a dab to the scissor
links at the pivot points.
Download from Www.Somanuals.com. All Manuals Search And Download.
MOTOR
Before motor is removed, it should be tested to be sure it is
inoperative. Check the continuity of the motor.
CHECK CONTINUITY
Black to Orange
Red to Orange
Gray to Orange
If open, replace motor
If open, replace motor
If open, replace motor
Green to Motor Frame
If open, inspect wire to
be sure it is properly
attached to motor
frame
1. Lower ram manually until there is approximately 7" between
the bottom assembly and the ram.
2. Disconnect molex connector from motor to wire harness.
3. Using a 3/8" nut driver or socket, remove the four nuts hold-
ing the motor to the gearbox. Remove air scentry tray and pull
motor out through front of compactor.
4. Install motor in reverse procedure.
WIRING SCHEMATIC
SCHEMATIC SHOWS UNIT AT END
L1
GN
N
COMPACTOR
SCHEMATIC
OF CYCLE - IN TOP POSITION
DRAWER OPEN
R
W
BK
GN
TR
V
OFF-ON
W
SAFETY SWITCH
GN
GN
NO
BK (or BR)
BR
Y
5
OR
C
4
SPEED
SWITCH
CW START UP
V
BK
R
2
1
3
C
C
START
BL/W
NC
NO
NC
NO
OL
CCW START DOWN
RUN
Y
OR
BR
C
BL
NO
KEY
SWITCH
GY
NC
Y
MOTOR
C
R
NO
TOP LIMIT
SWITCH
NC
INTERLOCK
SWITCH
NO
USAS SYMBOLS
C
NC
1
Y
C
2
3
4
5
V
NC
NC
NO
TR
HELD OPEN
NC
C
OFF - ON
START - RUN
KEY SWITCH
MOTOR
PLUG
NO
NO
HELD CLOSED
Download from Www.Somanuals.com. All Manuals Search And Download.
MODELS 1050-J,
1051-J, 1052-B
45
45
ITEM NO.
PART NO.
DESCRIPTION
Download from Www.Somanuals.com. All Manuals Search And Download.
70
FRONT
MODELS 1050-J,
1051-J, 1052-B
66
71
65
87
68
89
69
87
ITEM NO.
PART NO.
DESCRIPTION
Download from Www.Somanuals.com. All Manuals Search And Download.
126
125
129
157
MODELS 1050-J,
1051-J, 1052-B
124
127
ITEM NO.
PART NO.
DESCRIPTION
Download from Www.Somanuals.com. All Manuals Search And Download.
MODELS 1
1051-J, 105
Model 1052
154
153
158
ITEM NO.
PART NO.
DESCRIPTION
Download from Www.Somanuals.com. All Manuals Search And Download.
|