INSTALLATION MANUAL
FOR
VOLKSWAGEN - JETTA -1999.5-2005
VOLKSWAGEN - GOLF -1999.5-2006
VOLKSWAGEN - GTI - 1999.5-2005.5
Mount Location: To the right of the radio
MVM
Multi Vehicle Mount
MVM-45-05
Includes PHS-203 Ultra Slim Swivel
Thank you for purchasing your new Bracketron MVM Multi Vehicle Mount.
The Multi Vehicle Mount is an (end user-installer) modifiable professional mounting
bracket for most all mobile electronics requiring a steady and secure installation in a mo-
tor vehicle. The MVM installs behind your vehicles dash panel using existing or non-vis-
ible holes and is designed to cleanly protrude out from your vehicle’s dash panel.
Before installing, you must take the time to read and understand this installation manual
and read all the warnings accompanying this product.
Instructions Include: tools needed for install, directions for dash panel removal, directions
for modifying the MVM if required.
You can download this manual and any updates from
Download from Www.Somanuals.com. All Manuals Search And Download.
MVM MODIFICATION INSTRUCTIONS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
PLEASE NOTE
The Bracketron MVM-45-05 mount is a modifiable mounting bracket. The illustrations on the left show how this mount should
look during and after the modification steps in order to fit the listed vehicles on the front page of this manual. Many vehicle
applications may not require any modifications to the mount. If this is the case it will be noted below and there will be no steps
to follow on this page.
Before you begin to form your MVM, please make sure it looks exactly
the way it does in the top picture to the left.
Picture 1
6
To begin, use a marking pen to draw the lines on the MVM as
7
depicted in red in the middle picture to the left. Note: see red
lines in the middle picture for guidance.
Use a tin snips to cut along these lines. Then these cuts have been
8
made completely, continue by bending along the yellow lines as
depicted in the middle picture. Make this bend a 90° angle. If the
the bracket gets bent use a small hammer to pound out the imper-
fections. If the paint chips use some paint to cover up the paint.
Bend Mount Here
Picture 2
Now go back to Step 3 on the previous page to finish installa-
tion.
Cut Mount Here
Picture 3
Note: The hole pattern on the face of the MVM maybe
different then what is shown in the pictures.
Note: Please see page 3 in this manual for PHS-
203 Ultra Slim Swivel Instructions.
© Bracketron Inc, 2007 All rights reserved.
The information in this document is subject to change without notice. Bracketron Inc. assumes no responsibility for any errors that may appear in this document nor
do we assume any liability in connection with its use. This supersedes and voids all previous literature. Please contact the sales department for additional information.
Bracketron Inc will not be responsible or liable for damage to vehicles in the installation and or removal of this Bracketron Inc mount. Bracketron Inc will not be liable
for personal injuries or damage to property resulting from a motor vehicle accident and or improper installation of this Bracketron Inc mount.
Bracketron Inc 5249 West 73rd Street, Suite G, Edina, MN 55439
tel: 952-746-7775 fax: 1-800-660-1784 toll free: 1-866-237-4443
Download from Www.Somanuals.com. All Manuals Search And Download.
PHS-203 ULTRA SLIM SWIVEL INSTRUCTIONS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
PLEASE READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS BRACKETRON MOBILE SOLUTION.
This Professional Swivel Mount Solution is designed to be mounted to your MVM or any other 4 hole AMPs compatible mounting
device. The Ultra Slim Swivel is compact with a low profile and is designed to provide adjustability to devices such as Satellite
Radio Receivers, GPS monitors or Mobile Phones. The Ultra Slim Swivel angles your device for better viewing, tilting approx 15°
in all directions and swivels 360° degrees for maximum adjustability. All mounting hardware is included in the kit along with our
AMPs adapter plate to attach devices that support T- Notch mounting.
PARTS INCLUDED
1 - Ultra Slim Swivel
Note: The swivel can be installed before or after the mount is installed
in the vehicle. Attach the Ultra Slim Swivel to any MVM or CBM Mount or other AMPs
mounting device by inserting the M4x10 Pan Head screws through the holes on the
back half of the swivel. Align the screws up with the holes on the mount. Attach the M4
Nylon Locking Nuts only finger tight. Rotate the front half of the swivel to gain access to
the M4x10 Pan Head screws. (See Picture 1&2) Tighten all 4 screws with a #2 Phillips
screwdriver and 9/32” open end wrench.
1
1 - AMPs Adapter Plate
4 - M4 x 10 Hex Head
Screws
4 - M4 x 10 Pan Head Screws
4 - M4 x 12 Pan Head Screws
4 - M4 Hex Head Nuts
4 - M4 Nylon Locking Nuts
4 - M4 Star Washers
Picture 1
Picture 2
Picture 3
Rotate
Rotate
Adjust Hold Tension
Picture 4
Tighten the center screw to adjust the desired tension of the swivel. (See
Picture 3) Note: If Swivel becomes loose over time, you can grasp the
swivel and pull toward you lightly while rotating it clockwise. This will
tighten the swivel allowing you to create the desired tension needed.
2
3
For T- Notch Devices
Attach the AMPs T- Notch Adapter to the front half of the swivel
using the M4x12 Pan Head screws. Attach the M4 Star Washers and
M4 Hex Nuts to the screws and tighten the plate down with the #2
screwdriver and 9/32” open end wrench. Slide your device onto the
T- notch Adapter plate to secure it to the swivel. (See Pictures 4)
Picture 5
For AMPs Devices with Inserts
Attach your AMPs device using the M4x10 Hex Head screws and M4
Star Washers. Align the holes on the device with the holes on the front
half of the swivel. Slide the Star Washers onto the Hex Head screws.
Insert the screws through the swivel and into your device only finger
tight. Tighten down the device with the 9/32” open end wrench.
Your device is now secure to the swivel. (See Pictures 5)
© Bracketron Inc, 2007 All rights reserved.
The information in this document is subject to change without notice. Bracketron Inc. assumes no responsibility for any errors that may appear in this document nor
do we assume any liability in connection with its use. This supersedes and voids all previous literature. Please contact the sales department for additional information.
Bracketron Inc will not be responsible or liable for damage to vehicles in the installation and or removal of this Bracketron Inc mount. Bracketron Inc will not be liable
for personal injuries or damage to property resulting from a motor vehicle accident and or improper installation of this Bracketron Inc mount.
Bracketron Inc. 5249 West 73rd Street, Suite G, Edina, MN 55439
tel: 952-746-7775 fax: 1-800-660-1784 toll free: 1-866-237-4443
Download from Www.Somanuals.com. All Manuals Search And Download.
|