ADDS 3153 ASCII
Display Terminal
User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
chapter
1
Contents
Preface
v
This guide... ......................................................................................... vi
How to Connect/ Disconnect the Terminal................................................... vii
Notices.............................................................................................. viii
Trademarks and Service Marks................................................................. viii
Electronic Emission Notices...................................................................... ix
Safety Notices ....................................................................................... xi
Introduction
1
Features................................................................................................ 2
Compatibility ................................................................................. 2
Display .......................................................................................... 2
Character Sets.................................................................................. 2
Communications ............................................................................. 2
Keyboard ....................................................................................... 2
Desk Accessories .............................................................................. 3
Communications .................................................................................... 8
Receive Flow Control........................................................................ 8
Transmit Flow Control...................................................................... 9
Host/ Printer Port 2 ........................................................................ 11
Parallel Printer Port......................................................................... 11
Terminal to Modem (DCE) or Host..................................................... 12
Terminal to Host (DTE) or Printer...................................................... 12
Bottom Status/ Label Line Display...................................................... 13
Viewports..................................................................................... 13
Visual Effects of Screen and Page Lengths.............................................. 14
Installation
1 7
Download from Www.Somanuals.com. All Manuals Search And Download.
ii
Contents
STEP 1 – Know Your Devices.................................................................. 17
STEP 2 – Physical Connections................................................................. 18
STEP 3 – Number of Sessions Selection....................................................... 18
STEP 4 – Linking Ports to Sessions............................................................ 18
STEP 5 – No Printer Option .................................................................... 19
STEP 6 – Know Your Serial Port(S) Protocol............................................... 19
STEP 7 – Communications Setup Selections ................................................ 19
Connection A: Host DCE................................................................. 20
Connection B: Host DTE ................................................................. 20
Connection C: RS-232 with Modem ................................................... 20
Connection D: RS-232-C with Modem ............................................... 20
Connection E: Printer..................................................................... 21
Connection F: RS-232-C Printer........................................................ 21
Connections G and H: Parallel Printer.................................................. 21
STEP 8 – Emulation Setup Selection .......................................................... 21
STEP 9 – Additional Setup Options........................................................... 22
STEP 10 – Save Parameters...................................................................... 22
STEP 11 – Establish Communications........................................................ 22
Common Setups.................................................................................... 23
Host/ Printer Connection Guide................................................................ 24
User Settings......................................................................................... 26
Setup 2 7
Overview ............................................................................................ 27
Saving Parameters........................................................................... 28
Movement Inside Menus.................................................................. 28
Action Fields................................................................................. 29
Dual Session Mode.......................................................................... 29
Setup Map ........................................................................................... 30
QUICK: F1.......................................................................................... 32
GENERAL: F2..................................................................................... 34
DISPLAY: F3...................................................................................... 36
KEYBOARD: F4.................................................................................. 38
KEYS: F5 ........................................................................................... 40
PORTS: F6.......................................................................................... 43
HOST: F7 ........................................................................................... 45
PRINT: F8 .......................................................................................... 47
EMULATION: F9 ................................................................................ 48
ASCII Emulations........................................................................... 48
ANSI Emulations ........................................................................... 50
IBM Emulation.............................................................................. 51
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
iii
TABS: F10.......................................................................................... 52
ANSWERBACK: F11............................................................................ 53
PROGRAM: F12.................................................................................. 54
EXECUTE: Prnt Sc............................................................................... 56
Edit Fields........................................................................................... 57
Glossary of Terms.................................................................................. 58
Terminal Parameters ....................................................................... 58
Session Parameters.......................................................................... 59
Page Reset .................................................................................... 59
Des k Acces s ories
6 1
Overview ............................................................................................ 61
Desk Accessory Menu...................................................................... 61
Direct Access................................................................................. 62
Exit Keystrokes ............................................................................. 62
Inhibiting Access............................................................................ 62
Calendar.............................................................................................. 63
Clock ................................................................................................. 63
Calculator............................................................................................ 64
ASCII Chart......................................................................................... 66
Diagnostic Menu................................................................................... 67
Appendix
6 9
Local Keys........................................................................................... 69
Page Configurations—Single and Dual Session .............................................. 72
Download from Www.Somanuals.com. All Manuals Search And Download.
chapter
1
Preface
This product is in conformity with the protection requirements of EU Council
Directive 89/ 336/ EEC on the approximation of the laws of the Member States
relating to electromagnetic compatibility.
Boundless Technologies cannot accept responsibility for any failure to satisfy the
protection requirements resulting from a non-recommended modification of the
product, including the fitting of non-Boundless Technologies option cards.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
vi
Preface
This guide...
is a user’s manual and contains all of the information necessary to install, setup, and use
the 260 product.
More detailed information on programming using control codes and escape sequences,
default strings and character sets, international language support, etc. can be obtained
by calling the Boundle s s Te chnologie s Hotline at:
USA a nd Ca na da ca lls . . . .
Inte rna tiona l ca lls . . . . . . .
1 -8 0 0 -2 3 1 -5 4 4 5
1 -5 1 6-3 4 2 -7 4 0 0
At the options menu, press 2 for “Product Information,” then press 2 for “Products or
Program Information Mailed to You,” and request the following:
ADDS 3153 Programmer’s Reference Manual
Number:
5 9 8 -0 0 1 0 7 0 7
This manual is offered to our customers at no additional charge. When calling to
order, please have your terminal’s serial num ber available.
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Connect/ Disconnect the Term inal
vii
How to Connect/ Disconnect the Terminal
To Conne ct:
To Dis connect:
First, turn everything OFF.
First, turn everything OFF.
Attach all cables to devices.
Remove power cord from outlet.
Attach signal cables to receptacles.
Remove signal cables from receptacles.
Attach power cord to outlet.
Remove all cables from devices.
Turn device ON.
You may now take it with you.
Note: In the UK, by law, the telephone cable
must be connected after the power cord.
Note: In the UK, by law, the power cord must
be disconnected after the telephone line cable.
Download from Www.Somanuals.com. All Manuals Search And Download.
viii
Preface
Notices
References in this publication to Boundless Technologies products, programs, or
services do not imply that Boundless Technologies intends to make these available to
all countries in which Boundless Technologies operates. Any reference to a Boundless
Technologies product, program, or service is not intended to state or imply that only
Boundless Technologies’ product, program, or service may be used. Any functionally
equivalent product, program, or service that does not infringe any of Boundless
Technologies’ intellectual property rights may be used instead of Boundless
Technologies product, program, or service. Evaluation and verification of operation
in conjunction with other products, except those expressly designated by Boundless
Technologies, are the user’s responsibility.
This publication could contain technical inaccuracies or typographical errors.
This publication may refer to products that are announced but are not currently
available in your country. Boundless Technologies makes no commitment to make
available any unannounced products referred to herein. The final decision to
announce any product is based on Boundless Technologies’ business and technical
judgment.
The drawings and specifications contained herein shall not be reproduced in whole or
in part without the written permission of Boundless Technologies.
Trademarks and Service Marks
The following terms, denoted by
companies:
in this publication, are trademarks of these
™
CSA
ADDS Viewpoint
SCO
Canadian Standards Association
Boundless Technologies
Santa Cruz Operations
DEC VT-32/ 220/ 100
WYSE 50/ 60/ 120/ 150
TVI 925
Digital Equipment Corporation
Wyse Technology
TeleVideo Systems, Inc.
Underwriters Laboratories Inc.
UL
Download from Www.Somanuals.com. All Manuals Search And Download.
Electronic Em ission Notices
ix
Electronic Emission Notices
Federal Communication Commission (FCC) Statement
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at his
own expense.
Properly shielded and grounded cables and connectors must be used in order to meet
FCC emission limits. Boundless Technologies is not responsible for any radio or
television interference caused by using other than recommended cables and connectors
or by unauthorized changes or modifications to this equipment. Unauthorized
changes or modifications could void the user's authority to operate the equipment.
This device complies with Part 15 or the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Canadian Department of Communications Compliance Statement
This equipment does not exceed Class A limits per radio noise emissions for digital
apparatus, set out in the Radio Interference Regulation of the Canadian Department of
Communications.
Avis de conformité aux normes du ministère des Communications du
Canada
Cet équipement ne dépasse pas les limites de Classe A d'émission de bruits
radioélectriques pour les appareils numériques, telles que prescrites par le Règlement sur
le brouillage radioélectrique établi par le ministère des Communications du Canada.
Download from Www.Somanuals.com. All Manuals Search And Download.
x
Preface
J apanes e Voluntary Control Council for Interference (VCCI) Statem ent
This equipment is Class 1 Equipment (information equipment to be used in
commercial and industrial districts) which is in conformance with the standard set by
Voluntary Control for Interference by Data Processing Equipment and Electronic
Office Machines (VCCI) with an aim to prevent radio interference in commercial and
industrial districts.
This equipment could cause interference to radio and television receivers when used in
and around residential districts.
Please handle the equipment properly according to the instruction manual.
Korean Government Ministry of Communication (MOC) Statement
Please note that this device has been approved for business purposes with regard to
electromagnetic interference. If you find this is not suitable for your use, you may
exchange it for a non-business purpose one.
Download from Www.Somanuals.com. All Manuals Search And Download.
Sa fety Notices
xi
Safe ty Notice s
Danger Notices
A danger notice indicates a hazard that could possibly cause death or serious personal
injury.
The following danger notices are used throughout this manual.
DANGER: To prevent a possible electrical shock when installing the device, ensure
that the power cord for that device is unplugged before installing signal cables.
DANGER: To prevent a possible electrical shock when adding the device to a
system, disconnect all power cords, if possible, from the existing system before
connecting the signal cable to that device.
DANGER: To prevent a possible electrical shock during an electrical storm, do not
connect or disconnect cables or station protectors for communication lines, display
stations, printers, or telephones.
DANGER: To prevent a possible electrical shock from touching two surfaces with
different electrical grounds, use one hand, when possible, to connect or disconnect
signal cables.
DANGER: To avoid a shock hazard:
§
§
The power cord must be connected to a properly wired and earthed receptacle.
Any equipment to which this product will be attached must also be connected
to properly wired receptacles.
Download from Www.Somanuals.com. All Manuals Search And Download.
xii
Preface
DANGER: Electrical current from power, telephone, and communication cables is
hazardous. To avoid shock hazard, connect and disconnect cables as shown on the
following page when installing, moving, or opening the covers of this product or
attached devices.
DANGER: The device’s switch is not the main disconnect. The device’s main
power disconnect is the detachable line cord.
Caution Notice
A caution notice indicates a hazard that could possible cause minor personal injury.
CAUTION: This product contains a lithium battery. Do not attempt to exchange or
charge the battery. Discard the product as instructed by local regulations for limited
lithium batteries. Do not burn.
Warning Notice
A warning notice indicates the possibility of damage to a program, device, system, or
data.
Download from Www.Somanuals.com. All Manuals Search And Download.
chapter
1
Introduction
This terminal can emulate a number of ASCII
and ANSI terminals, including IBM 3151,
PC-Term and SCO™ Console. The keyboards
supported by the terminal are the 101-key
extended PC (EPC), the 106-key PC+, and the
ANSI keyboards. The dual host capability of the
terminal allows you to run two different
applications simultaneously. A Setup option is
available to view each “session” on the screen in
a split or full screen display.
Clock, calendar, calculator, ASCII chart,
and diagnostic desk accessories are
provided. Another feature is the selectable
overscan border which can provide bezel-
to-bezel video.
This terminal also features an easy-to-use Setup menu that is configuration dependent;
thismeans that only the options that are valid for a given emulation or hardware
configuration are presented.
Setup also has a “Quick” menu that summarizes the options most critical to the
operation of the terminal. Travel between menus is facilitated by function keys that
are listed at the top every menu.
Split screen is not available if one of the sessions is selected as IBM 351 emulation.
Features
Com patibility
§
§
§
§
IBM™ 3151
ADDS-Viewpoint™
Wyse™ 60, Wyse 50/ 50+
DEC™ VT-320, VT-220, VT-100
1
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Introduction
§
§
§
PC Terminal
SCO™-Console, AT386
TVI™-925
Display
§
§
§
§
§
§
§
§
§
Dual session available in full or split screens
100 Hz refresh rate (flicker-free)
Selectable overscan borders
Selectable screen saver
26, 30, 44 or 52 row display with top and bottom status lines
80 or 132 column display
Double high/ double wide display
Up to 10 pages of memory
Tilt and swivel base, small footprint
Characte r Se ts
§
Numerous standard, graphic, and supplemental character sets
Communications
§
§
§
§
Serial RS-232-C host/ printer port 1 operating from 110 to 134,400 baud
Optional RS-422 host port 1 (EIA only)
Serial RS-232-C host/ printer port 2 operating from 110 to 38,400 baud
Parallel IBM™/ Centronics™ compatible printer port
Keyboard
§
§
§
PC 104/ 105-key keyboard
ANSI keyboard
Up to 35 shiftable and programmable edit and function keys
Des k Acces s ories
§
§
§
§
Calculator capable of transmitting results
Monthly Calendar
Clock with alarm settings
ASCII and Diagnostic charts
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
3
Physical Features
1
4
2
3
5
6
7
8
9
1 .
2 .
Ke yboard Conne ctor – Push in the keyboard connector here.
Tilt and Swivel Bas e – Use the tilt and swivel arrangement to adjust the viewing
angle. Grasp the lower corners of the terminal and push up or down, or twist left
or right.
3 .
P ower Switch – “0” is off; “1” is on.
Leave the terminal’s power switch in the off position “0” until power, keyboard,
and communication connections are made.
4 .
Contras t Dial – Adjust the contrast between characters of different intensities by
rotating the dial.
5 .
6 .
Brightne s s Dial – Adjust the overall screen brightness by rotating the dial.
P owe r Conne ction – Plug the female end of the power cord into this connector
and the male end of the cord into a properly grounded receptacle.
The Canadian Standards Association (CSA) recommends that the power outlet be
near the terminal and easily accessible at all times.
7 .
P aralle l P rinte r P ort – Connect the cable from the IBM or Centronics
compatible parallel printer to this port. See the “Installation” chapter for
options.
8 .
9 .
Hos t/ P rinter P ort 2 – Connect the cable from a second host (dual-host mode) or
serial printer here. See the “Installation” chapter for options.
Hos t/ P rinter P ort 1 – Connect the cable from the first host or serial printer here.
See the “Installation” chapter for options.
Keyboards
The “PC-style” keyboards, the PC – US (104-key) and the PC – Int’l (105-key), are similar in
style and feature a number of key groups.
The alphanumeric keypad is the main typewriter keypad, while the function key group lies
along the top of the keyboard and can be programmed locally or downloaded from the host.
The numeric keypad is the calculator-style set of keys on the right-hand side of the keyboard,
used to enter numeric data.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Introduction
The cursor and edit keypads, located to the left of the numeric keypad, allows users to edit text
and move around in the document. The communication key group, above the edit keypad, is
used to control communications with the host or printer.
The PC keyboard is configured as an IBM 3151 ASCII keyboard and is for use primarily with
the 3151 emulation.
The ANSI keyboard varies from the PC-style keyboard styles mainly in that it features 20
function keys, a set of PF-keys, and a different style numeric keypad.
For each keyboard, there is a set of local “hot-keys.” They perform a variety of terminal
functions, such as “Print Screen” and “Enter Setup.” (See the Appendix for a complete list of
local functions.)
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
5
104-key PC Keyboard (US)
ANSI Keyboard
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Introduction
Us age Notes
The following notations and symbols are used in this manual:
§
§
§
Ctrl-F1 : the two keys, Ctrl and F1 , are to be pressed simultaneously.
Ctrl, F1: the two keys, Ctrl and F1 , are to be pressed in succession.
1-num or 1-alph: specifies that the number must be generated either from the
numeric or the alphanumeric keypad.
§
§
23h: the number 23 is represented in hexadecimal (hex) notation.
applies to ASCII emulations only: ADDS-VP, Wyse 50+, Wyse 60, PC
Term, and TVI-925.
§
§
applies to ANSI emulations only: VT300/ 8, VT300/ 7, VT200/ 8,
VT200/ 7, VT100, SCO Console, and AT386.
applies to SCO Console and AT386 emulations only.
applies to IBM 3151 emulation only.
§
§
applies to parallel attribute emulations only which includes all emulations
except ADDS-VP and Wyse 50+ (which are field attribute emulations).
§
§
applies to ASCII key-mode only.
applies to Scan Code-key mode only.
§
§
applies to the PC-style keyboards (PC+ and EPC) only.
applies to the ANSI keyboard only.
Download from Www.Somanuals.com. All Manuals Search And Download.
Com m unications
7
Communications
This terminal is equipped with three ports. The two serial ports are intended for
connection to either a host/ modem or a serial printer. The remaining port is a
Centronics-compatible printer port. The port you use as the printer port depends on
whether you have a serial or a parallel interface to the printer. Another factor affecting
your port selection is your choice of connecting the terminal to one or two host
computers.
The first host/ printer serial port (SES1-EIA) can communicate with your computer or
printer at a baud rate of 110 to 134,400 baud (bits per second). The second
host/ printer serial port (SES2-AUX) can communicate at speeds from 110 baud to
38,400 baud. Either port can be used to connect to a host computer/ modem or serial
printer.
In single host mode, you have the choice to use the second serial port or to use the
parallel printer port, as your printer interface. In dual host mode, the natural choice is
to use the parallel port, although other options are available (See the “Installation”
chapter). Refer to the following sections for further information on these ports.
Receive Flow Control
Because devices can receive data faster than they can process it, data flow control
(selectable in the PORTS menu of Setup) should be used to prevent data loss. Software
flow control relies on the Xon and Xoff characters (“g” and “e” characters in Scan
Code Key mode) to indicate when the terminal is able or unable to store further data.
The Xon signal transmits the DC1 character (11h) and the Xoff signal transmits DC3
(13h).
The terminal’s receive buffer can store 1024 bytes (characters). When “EIA (or Aux)
Rcv” in the Setup menu for PORTS is “Xon-Xoff,” the terminal issues an Xoff
character, indicating to the host that it should stop transmitting a. The terminal will
then continue to process data until its receive buffer is empty. It will then issue an
Xon character to the host, indicating that it can resume sending data to the terminal.
If the “EIA (or Aux) Rcv” is “No Protocol” in Setup, the terminal wll continue to
accept characters into its receive buffer until it is full. Additional chaacters will be
lost. Xon-Xoff protocol must also be set on the host computer or priter for proper
handshaking.
In addition to software “receive” flow control (Xon-Xoff), the serial host/ printer
ports support “receive” hardware flow control. The SES1-EIA port has an outgoing
DTR (Data Terminal Ready) signal. If “EIA Rec” is “DT” in Setup, and the
terminal’s receive buffer fills to the level mentioned above, the terminal will set the
DTR signal low to inform the (serial) host device to stop sending data. On the SES2-
AUX port, the incoming DSR (Data Set Ready) signal serves to signal the host (serial)
device that the terminal is not ready to receive more data, if “Aux Recv” is “DSR” in
Setup.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Introduction
Trans m it Flow Control
Likewise, the terminal will understand the Xon and Xoff requests from the host when
it is transmitting data (provided the “EIA (or Aux) Xmt” is “Xon-Xoff” in Setup).
This is referred to as “transmit” flow control.
This terminal will stop transmitting data to the host or printer when it receives an Xoff
(DC3) code. If, however, the terminal needs to send a receive protocol character, it
will transmit that character even if it has received an Xoff code. When the terminal
stops transmitting, the data will be buffered in the transmit buffer (64 characters for
the first host/ printer port and 64 characters for the second host/ printer port). Once
the buffer is full, additional keyboard data will be lost. When an Xon (DC1) character
is received, the terminal can again send data to the attached serial device.
In addition to software “transmit” flow control (Xon-Xoff), the serial host/ printer
ports support “transmit” hardware flow control, whereby DSR on the SES1-EIA port
and DTR on the SES2-AUX port monitor serial devices to control the flow of data to
them (provided EIA and AUX Xmit is “DSR” and “DTR” in Setup).
For parallel printers, this terminal monitors the BUSY and ERROR signals which are
sent by the printer to determine when data transmission should be stopped or
resumed.
Download from Www.Somanuals.com. All Manuals Search And Download.
Com m unications
9
Hos t/ P rinte r P ort 1 (RS-2 3 2 -C or RS -4 2 2 )
This port, labeled “SES1-EIA,” is designed for connection to the host (computer or
modem) or a serial printer via a 25-pin D-shell (DB25P) female connector. This port
uses an RS-232-C communication interface, is configured as a DTE (Data Terminal
Equipment) device, and can operate from 110 to 134,400 baud. The pins supported
are shown below:
RS-232-C Host/Printer Port 1 Pin Assignments
This port also uses (if installed) an optional RS-422 communication interface and can
also operate from 110 to 134,400 baud. The pins supported are shown below:
13 12 11 10
9
8
7
6
5
4
3
2
1
25 24 23 22 21 20 19 18 17 16 15 14
L(in)+
L(out)+
L(out)
-
L(in)
-
RS-422 Host/Printer Port 1 Pin Assignments
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Introduction
Hos t/ P rinte r P ort 2
This port, labeled “SES2-AUX,” is designed to connect to a second host connection
(computer or modem) or a serial printer, and can operate from 110 to 38,400 baud.
This port uses an RS-232-C interface via a DB25P female connector, and is configured
as a DCE (Data Communication Equipment) device. The pin assignments for this
port are shown below:
Host/Printer Port 2 Pin Assignments
Refer to the Installation chapter for details on the connection of all pots to serial
devices (hosts, modems, or printers).
P arallel P rinter P ort
This port, labeled “PAR,” is designed for connection to a parallel printer, which has a
Centronics interface with a 25-pin D-shell female connector. This port, unlike the
others, is a uni-directional device, which means that it only serves to output data to
the printer, and cannot receive. The pins and signals supported are shown below:
Parallel Port Pin Assignments
* These signals are held high, in an inactive state.
If you have opted to use a parallel printer, but it is not connected, an error message
will appear on the status line when any PRINT operation is done. To clear the
message, press Ctrl-Shift-Tab.
Terminal to Modem (DCE) or Hos t
Refer to the diagram below to understand why a null modem adapter may be needed
when connecting the second serial port (SES2-AUX) to a modem or a DCE host. The
first host will connect directly without a null modem since it is a DTE device.
Download from Www.Somanuals.com. All Manuals Search And Download.
Com m unications
11
Host
Host
SES1 EIA
DTE
SES2 AUX
DCE
D
C
E
D
C
E
Modem
Modem
pin2
pin2
pin2
pin2
Transmit
Receive
DTR
Transmit
Receive
Transmit
pin3
pin20
pin6
pin3
pin20
pin6
pin3
pin20
pin6
pin3
pin20
pin6
Receive
DTR
Transmit
Receive
DTR
DSR
DTR
DSR
DSR
DSR
Term inal to Hos t (DTE) or P rinter
Refer to the diagram below to understand why a null modem adapter may be needed
when connecting the first serial port (SES1-EIA) to a host port without a modem
(Most serial printers are DTE devices and most hosts are not). The second port (AUX)
will connect directly without a null modem since it is a DCE device.
Host
Host
SES2AUX
SES1EIA
Serial
Printer
Serial
Printer
D
T
E
D
T
E
DCE
DTE
pin2
pin2
pin2
pin2
Receive
Transmit
DTR
Transmit
Transmit
Receive
Transmit
pin3
pin20
pin6
pin3
pin20
pin6
pin3
pin3
pin20
pin6
Receive
DTR
Receive
DTR
pin20
DTR
DSR
pin6
DSR
DSR
DSR
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Introduction
Screen Display and Pages
This terminal offers a variety of screen lengths including 26, 30, 44, or 52 lines. These
numbers include the top and bottom status lines (or label line), as well as the lines used
to display data. A “page” of terminal memory represents the total number of lines that
can be accessed, whether or not they are all viewable on the screen at once. Refer to
Appendix A for the number and lengths of pages available for your setup.
The page length is comprised of a base page length multiplied by 1,2,4, or 8. For
instance, in certain modes, 24 (24x1), 48 (24x2), and 96 (24x4) are available, the
same way that 25(25x1), 50 (25x2), and 100 (25x4) are. The base page length and the
screen size determine whether a bottom status line or label line is displayed or not.
Bottom Status / Label Line Dis play
With a screen length of “26 lines,” the page lengths that are multiples of 24 allow the
bottom status/ label line to be displayed, while those that are multiples of 25 do not.
The same idea applies with the 44 line screen size. A page length with 42 lines as a base
page size will display a label line, while the 43 line base page length will not. An
exception to this rule is if the screen length is significantly larger than the that page size,
then the label line will be displayed, such as if the screen is 44 lines and the page length
is 25 lines.
Vie wp orts
Up to three viewports can be selected on a page. Each viewport has its own
character attribute, cursor position, field attribute propagation, tab stops and scrolling
region. All of the viewports are displayed on the same screen and can be partitioned
with a visual separator line. If the keyboard is associated with one viewport and the
host is associated with another, it is possible to receive data in two viewports
simultaniously.
Download from Www.Somanuals.com. All Manuals Search And Download.
Com m unications
13
The figure below represents the entire page memory of a 48 line page (24 base page
length times a multiplier of 2) and the portion of the page that is viewable on the
display screen, when “26 Lines” is selected. Notice that the label line is visible in this
mode.
Vis ual Effe cts of Scre e n and P age Le ngths
The combination of page and screen lengths influence the number of displayable data
lines. For example, if the page length is “50” (25 x 2), and the screen length is 44
lines, the number of data lines that are visible at any one time is 43, with no label line.
The other line is used for the top status line. On a 52 line screen, 50 of the 52 data lines
are visible at one time, in single session mode.
If the page length is shorter than the screen length, then blank lines will be present
below the data line or status/ label line. If the page length is larger than the allowable
number of data lines, this will cause some of the rows to be out of view. In order to
bring them into view, “scrolling” or “panning” is used, as necessary.
Scrolling causes a new line to scroll into view when the cursor advances past the last
row or first row on the page. If the cursor moves past the last row, the top row of text
is lost, and past the first row, the bottom row of text is lost (ifAuto Scroll is “on” in
Setup). Text scrolled off of the screen is not recoverable.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Introduction
If the current page or portion of the page is longer than the screen display or window in
which it is displayed, then local keystrokes can be used to “pan” the window up or
down (Ctrl-• and Ctrl-¯). As a window is panned up, the page appears to be moving
down and the opposite is true when panning the window down. Text that is panned
off the screen is out of view, but is not lost.
The figure below represents the display screen with a 48 line page length on a 44 line
screen, after panning the window down 2 lines.
Download from Www.Somanuals.com. All Manuals Search And Download.
chapter
2
Installation
This section provides a “walk-through” approach to the installation of your terminal.
This will enable you to physically connect the terminal to a printer and one or two host
computer(s)/ modem(s), as well as to configure the Setup menu to suit your
requirements and preferences.
The terminal is designed to provide great flexibility in configuring the terminal. An
example of the flexibility is apparent in the fact that either the EIA or Aux ports can
be used to connect either to a host or a printer port. In addition, a physical port can be
assigned as a host port in one session and as a printer port in the other session, if
desired. In another case, data can potentially be “printed” from one session to the
other.
The procedures described here are among the most common. Described here are
conventional single and dual host setups, with or without a printer. These steps may
need to be adjusted to meet your requirements.
S TEP 1 – Know Your Devices
The first step in our installation process will be to determine what type of serial ports
you are connecting to the terminal. The Communications section in the Introduction
chapter describes the differences between a DTE and DCE serial device. Determine
what type of devices you are using (a DTE host, a DCE modem, a DTE printer, a
parallel printer, etc.).
S TEP 2 – Physical Connections
Depending on the types of serial interfaces of your devices, you may need one or more
“null modem” adapters to communicate properly.
First, refer to the Common Setups diagrams later in this chapter. If one of these setups
matches your needs, then make the connections as shown in the diagrams by referring
to the Host/ Printer Connection. Each cable connection in the diagram (the lines with
arrows on each end) has a letter next to it.
The letters correspond to the letters in the Host/ Printer Connection Guide. If these
set-ups don’t apply, then choose the connections in the Host/ Printer Connection
Guide that are appropriate.
Your physical connections are now complete.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Installation
S TEP 3 – Number of Sessions Selection
This step requires setting a selection in the Setup menu to configure the terminal for
single or dual session mode.
If you’ve connected two host cables (A or C AND B or D), and you wish to run in
“dual session” mode, enter Setup and set “Sessions=Two” in the Quick (F1) menu.
For single host operation, this setting should already be set at “One” since this is in the
default state.
To access the Setup menu, press Ctrl-Scroll Lock on a PC-style keyboard or F3 on
an ANSI keyboard.
S TEP 4 – Linking Ports to Sessions
If you have selected “Sessions=One,” then you can skip to Step 5. If you have
selected “Sessions=Two,” there are four designations to make. This step will be used
later in Step 7.
First, you have to decide which serial port will be assigned to your first host in Session
1 (either EIA, Aux, or None). Now, decide which port will be used for your second
host in Session 2 (EIA, Aux, or None). The sam e port should not be used as the
host port for both sessions. Then, determine which port will be used as the printer
port in Session 1 (EIA, Aux, Parallel, None). Do the same for the printer option in
Session 2.
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 – No Printer Option
19
Note that it is not general practice to assign the host port in one session as the printer
port in another session, but this can be done if desired.
If RS-422 daughter board is installed in the EIA port, it cannot be usd with a
printer.
STEP 5 – No Printer Option
If you did not opt to install a printer (did not complete E, F, G, or H), you must set
the Printer portion of the Host/ Printer selection in the Quick (F1) Setup menu to
“None.” Choose the combination of Host/ Printer that properly represents which
terminal port you are connecting the host to, and “None” as the printer. For example,
if the EIA port is connected to the host or modem, the setting would be “EIA/ None.”
If you are running in dual session mode, press Ctrl-Enter (num ). Now, set the Printer
portion of Host/ Printer to “None” in Session 2, preserving the current Host setting.
S TEP 6 – Know Your Serial P ort(S) P rotocol
Consult your system administrator to find out the communication settings on all the
serial devices you've connected to, including EIA (or Aux) baud, data bits, stop bits,
parity, parity checking on/ off, Xmt and Rcv flow control protocol. This could
include one or two hosts/ modems, or a serial printer. Record this information on the
User Settings later in this chapter for reference in Step 7.
S TEP 7 – Communications Setup Selections
To complete this step, you must recall the letters next to the connections that you
made in Step 2. Also, you must be aware of the port/ session designations made in
Step 4 (see the Host/ Printer Connection diagrams later in this chapter).
The procedures below correspond directly to the individual connections made.
Notice that only certain connection procedures are to be followed, not all of them.
For example, if you've made connections “C” and “F,” to a modem and a serial
printer, then follow connection procedures “C” and “F” below.
Only follow those steps that apply to your connections (A-H).
To access the Setup menu, press Ctrl-Scroll Lock on a PC-style keybord or F3 on
an ANSI keyboard.
Conne ction A: Hos t DCE
1 .
2 .
3 .
Enter the Setup menu. If the EIA port is to be assigned to Session 2, then switch
sessions (Ctrl-Enter (num )). Remain in session 1, if it is to be assigned to that
session.
In the Setup Quick (F1) menu, set the Host portion of the “Host/ Printer”
selection to “EIA” without changing the current Printer option (“EIA/ xxxx”).
The Printer will be set in another connection procedure if needed.
In the Ports (F6) menu, set the proper communications settings for the EIA
Baud, EIA Data Format, EIA Parity Check, EIA Recv, and EIA Xmt selections.
See the Setup chapter for more information on the individual settings.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Installation
Connection B: Hos t DTE
1 .
2 .
3 .
Enter the Setup menu. If the Aux port is to be assigned to Session 2, then switch
sessions (Ctrl-Enter (num )). Remain in session 1, if it is to be assigned to that
session.
In the Setup Quick (F1) menu, set the Host portion of the “Host/ Printer”
selection to “Aux” without changing the current Printer option (“Aux/ xxxx”).
The Printer will be set in another connection procedure if needed.
In the Ports (F6) menu, set the proper communications settings for the Aux
Baud, Aux Data Format, Aux Parity Check, Aux Recv, and Aux Xmt. See the
Setup chapter for more information on the individual settings.
Conne ction C: RS-232 with Modem
1 .
2 .
Follow all procedures of Connection A, step 1 through step 3.
If you are connecting to a modem, in the Ports (F6) menu, set the “EIA Modem
Control” parameter to “On”.
Conne ction D: RS-2 3 2 -C with Modem
1 .
2 .
Follow all procedures of Connection B, step 1 through step 3.
If you are connecting to a modem, in the Ports (F6) menu, set the “Aux Modem
Control” parameter to “On”.
Conne ction E: P rinte r
1 .
In the Setup Quick (F1) menu, set the Printer portion of the “Host/ Printer”
selection to “EIA” without changing the current Host option (“xxxx/ EIA”).
The Host will be set in another connection procedure if needed.
2 .
Follow procedure of Connection A, step 3.
Connection F: RS-2 3 2 -C P rinte r
1 .
In the Setup Quick (F1) menu, set the Printer portion of the “Host/ Printer”
selection to “Aux” without changing the current Host option (“xxxx/ Aux”).
The Host will be set in another connection procedure if needed.
2 .
Follow procedure of Connection B, step 3.
Connections G and H: P arallel P rinter
1 .
Enter the Setup menu. If the PARA port is to be assigned to Session 2, then
switch sessions (Ctrl-Enter (num )). Remain in session 1, if it is to be assigned to
that session.
2 .
3 .
In the Setup Quick (F1) menu, set the Printer portion of the “Host/ Printer”
selection to “Para” without changing the current Host option (“xxxx/ Para”).
Repeat this procedure if the parallel port is going to be used to print from both
sessions.
Only one session can access the parallel printer at one time.
If a print mode (Aux on, etc.) is on in both sessions, an error message will appear.
To disable a print mode in a session, press Shift-Scroll Lock on a PC-tyle keyboard
or Shift-F3 on an ANSI keyboard.
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 8 – Em ulation Setup Selection
21
S TEP 8 – Emulation Setup Selection
This step requires setting a selection in the Setup menu to configure the “Emulation”
for one or two sessions of the terminal. Determine which emulations your
applications run with.
Enter the Setup menu and set the “Emulation” parameter, in the Quick (F1) menu, to
match your requirements. If you are running in dual session mode, press Ctrl-Enter
(num ). Now, set the “Emulation” parameter in Session 2.
S TEP 9 – Additional Setup Options
At this point, you should proceed to the Setup chapter and continue to set up your
own selections for any other parameters such as those for the display, keyboard,
function/ edit keys, and tabs.
Remember to repeat this procedure for Session 2 if you are running in dual session
mode. Use Ctrl-Enter (num ) to access this set of parameters.
S TEP 1 0 – Save Parameters
Finally, remember to save your Setup parameters in permanent memory, so that they
can be recovered if the terminal is powered down. When you exit the Setup menu,
the prompt “Save all? (Y/ N)” flashes. To save parameters, press “Y”. Another way to
save parameters is to perform a “Save Terminal” operation, while in the Exec
(F13/ Prnt Scrn) menu of Setup. Both methods will save the parameters in both
sessions, as well as those that are common to both.
Remember to save your Setup settings after the entire installation procss.
S TEP 1 1 – Establish Communications
Your installation is now complete. By pressing the Return or Enter key, you should be
able to communicate with the host computer(s). The printer should respond to the
local print command, Shift-Ctrl-. (period on num eric keypad).
If for some reason, your installation was not successful, make sure your physical
connections are secure, that the communications protocol settings match your devices
and that the Setup selections are chosen to provide a proper interface between the
terminal and your devices.
If you continue to have problems installing the terminal, call your local dealer for
technical support.
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Installation
Common Setups
TERMINAL
T E R M I N AL
H
O
S
T
EIA AUX PAR
EIA AUX PAR
M O D E M
To
C
B
H
F
DTE
H O S T
D C E
S ERIAL
PARALLEL
PRINTER
P RINTER
Sessions=One
Host/ Printer=EIA/ Aux
EIA/ Baud, etc. matches the host
Aux Baud, etc. matches the printer
EIA Modem Control=On
Sessions=One
Host/ Printer=EIA/ Para
EIA Ba ud, EIA Da ta Form a t, etc.
matches the host
T E R M I N AL
H
T E R M I N AL
O
S
T
H
EIA AUX PAR
M O D E M
EIA AUX PAR
O
S
T
T o
O
N
C
H O S T
1
2
D C E
E
A
T
DTE
M O D E M
T o
W
O
D
H
H O S T
B
D C E
DTE
P AR ALLE L
P RIN TER
Sessions=Two
Sessions=Two
Session1 Host/ Printer=EIA/ Para
Session2 Host/ Printer=Aux/ Para
EIA Baud, etc. matches host 1
Aux Baud, etc. matches host 2
EIA Modem Control=On
Session1 Host/ Printer=EIA/ None
Session2 Host/ Printer=Aux/ None
EIA Baud, etc. matches host 1
Aux Baud, etc. matches host 2
Aux Modem Control=On
Host/ Printer Connection Guide
CAUTION: Do not (un)plug in electrical storm.
Download from Www.Somanuals.com. All Manuals Search And Download.
Host/ Printer Connection Guide
25
SES1-EIA (DTE)
SES-AUX (DCE)
PA
DTE Host*
Connection A:
Connect a null
modem adapter
between the host
cable and the EIA
port.
Connection B:
Not applicable.
Connect the host
cable directly to
the AUX port.
DCE Host
or Modem
Connection D:
Connection C:
Connect the host
or modem cable
directly to the EIA
port.
Not applicable.
Connect a null
modem adapter
between the host
or modem cable
and the AUX port.
* Most host computers are configured as DTE devices.
®
The ADDS Mentor System is an example of a DCE host system, The above
connections assume RS-232 configuration for the EIA port.
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Installation
SES1-EIA (DTE)
SES2-AUX (DCE)
PAR
DTE Serial
Printer**
Connection G:
Connection E:
Connection F:
Connect the serial
printer cable
directly to the
AUX port.
This is an option if
you connect a
parallel-to-serial
converter between
the serial printer
cable and the PAR
port.
Connect a null
modem adapter
between the serial
printer cable and
the EIA port.
Paallel Printer
(Cntronics/
IB)
Connection H:
Not applicable.
Not applicable.
Connect the parallel
printer cable to the
PAR port.
** Most serial printers are configured as DTE devices. The above connections
assume RS-232 configuration for the EIA port.
Us e r Se ttings
Use the chart below to document your system and terminal settings:
Param eters Exam les: Your Settings:
Download from Www.Somanuals.com. All Manuals Search And Download.
User Settings
27
Connections made
Number of sessions
C, Dand H
2
Host/Printer (Session 1)*
Host/Printer (Session 2)*
Emulations (Session 1)
Emulations (Session 2)
EIA/ara
Aux/None
IBM 151
ADDS VP
Host 1:
9600
8
Baud
Data Bits
1
Stop Bits
Non
Off
Xon-off
Xon-off
On
Parity
Parity Check
Flow Control (In)**
Flow Control (Out)***
Modem Control
(Dual Host mode only)
Host 2:
Baud
19200
Data Bits
7
Stop Bits
2
Parity
Odd
Parity Check
Flow Control (In)**
Flow Control (Out)***
Modem Control
On
DTR (or DSR)
DTR (or DSR)
Off
*
In most cases, these parameters should not be the same.
** Incoming flow control on the host should correspond to
“EIA (or Aux) Rcv.”
*** Outgoing flow control on the host should correspond to
“EIA (or Aux) Xmt.”
Download from Www.Somanuals.com. All Manuals Search And Download.
chapter
3
Setup
The Setup menu is your control panel for this terminal. It permits you to configure the
terminal to communicate with the host computer as well as to suit your personal
preferences.
Overview
The Setup menus have been designed to allow maximum flexibility with a minimum
investment of time. Thirteen menus provide you with the flexibility and the features
below contribute to ease of use:
§
§
§
The Quick menu is the first screen upon entry. It contains the param eters critical
to the operation of the terminal with the host.
Function keys permit easy access to any menu. The function keys are labeled at
the top of every menu.
Setup is “smart.” That is, it provides only the options that are valid for the
hardware and current emulation.
§
§
Keystrokes and Help Messages are at the bottom of every menu.
Valid choices for the selected parameter are displayed at the bottom of the menu.
Entry and Exit
PC-Style Keyboards: Press Ctrl-Scroll Lock to both enter and exit setup. Also,
press Esc or Pause to exit.
IBM 3151 em ulation: Press Ctrl-Setup to both enter and exit setup.
ANSI Keyboard: entry is dependent upon the Setup selections:
When “F1 to F5 keys” = Local, press F3 to enter.
§
§
§
When “F1 to F5 keys” = FKey, press Ctrl-F3 to enter.
When “Key Mode” = Scan Code, press Ctrl-Select to enter.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
28
Setup
Saving P aram eters
Upon exiting setup mode, the prompt “Save All (Y/ N)” blinks. Press Y or y to exit
setup and save settings in permanent (nonvolatile) RAM. Press C or c to cancel the exit
request. Press
N or n to exit Setup. The changes will take effect, but will be lost if the terminal is reset
or powered off.
An exception to this is function/ edit key and answerback message pogramming.
Once edited in Setup, the changes are saved regardless of the way in which you exit
Setup.
Movement Inside Menus
F1 through F1 2 : Select the menu that corresponds to the function key. Access to the
“EXEC” menu is available using either the Print (PC-style keyboards) or F13 (ANSI
keyboard) key. The keys are labeled at the top of each menu.
Cursor Control Keys (• ¬ ¯ ® ): These keys control movement to parameters within
the menu and is indicated by a highlighted selection bar. This selection bar will wrap
to the other side of the menu at the top, bottom and side boundaries. For each
parameter there are at least two choices. As the parameter is highlighted, the available
choices appear in the area above the help bar.
Some parameters are action fields and have no choices. See the Action Fields
section later in this chapter.
Enter and Shift-Enter: Cycle “up” or “down” through the choices for a given
parameter.
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
29
The following keystrokes are also available but are not documented ithe Setup
help bar.
Tab and Shift-Ta b : Move from menu to menu forward or backward without using
function keys.
Space and Shift-Space: Cycle through the list of choices. Same as Enter and
Shift-Enter.
Parameters that are changed are executed as soon as that field is exite. Page resets
may occur when certain choices are made in Setup.
Action Fields
Certain parameters are not selections but action fields. When the action field is
highlighted and then selected, the action is taken. A “WAIT” message may appear at
the top right portion of the screen, and when the action is completed, a “DONE”
message will appear. These messages are cleared when the selection bar is placed on
another parameter.
Dual Session Mode
There are two “sets” of “session” setup parameters, if you are using the terminal in
dual session mode. To toggle between sessions while in or out of setup mode, press
Ctrl-Enter (num ). For a complete explanation of session dependent and terminal
dependent parameters, see the Glossary of Terms section at the end of this chapter.
Download from Www.Somanuals.com. All Manuals Search And Download.
30
Setup
Setup Map
Ke y
Me nu
P aram eters Available
(Not all will display for a given em ulation, keyboard, or video m ode)
F1
Quick
Em ulation
Enhanced
EIA Da ta Form a t
Aux Data Form at
Com m Mode
La ngua ge
Host/ Printer
EIA Baud Rate
Aux Baud Rate
Sessions
F2
General
Em ulation
Enhanced
Auto Wrap
Auto Font Loa d
Monitor Mode
Warning Bell
Session Display
Auto Page
Screen Saver
Cursor Dir
Bell Length
Auto Scroll
Bell Volum e
Sessions
Setup La ngua ge
F3
Display
Page Length
Display Cursor
Colum ns
Screen Video
Scroll
Width Change Clea r Auto Adjust
Cursor
Overscan Borders
Cursor
Screen Length
Refresh Rate
Speed
Pages
Viewports
Viewport 1 Bottom Row
Viewport 2 Bottom Row
F4
F5
Keyboard
La ngua ge
Margin Bell
Key Lock
Key Repeat
Key Mode
Key Rate
Keyclick
Char Set
Caps Lock
Num Lock
Code Page
Keys
Enter Key
Alt Key
Return Key Repeat
UDKs
Return Key
Pound Key
Desk Acc
Backspace
Local Leadin
Disconnect
Send Key
New Line
Insert Character
Keys
Enter Key
Return Key
Pound Key
F1 to F5 keys
Del key
Com pose Key
Return Key Repeat
,, and .. key
UDKs
Local Leadin
Disconnect
<> key
` a nd
~
F6
Ports
EIA Baud Rate
Aux Baud Rate
EIA Xm t
EIA Da ta Form a t
Aux Data Form at
EIA Recv
EIA Parity Check
Aux Parity Check
EIA Xm t Pace
Aux Xm it
Aux Recv
Aux Xm t Pace
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Map
31
Ke y
Me nu
P arameters Availa b le
(Not all will display for a given em ulation, keyboard, or video m ode)
F7
Host
Com m Mode
Recv <DEL>
Send Block Term
Null Suppress
Line Control
Loca l
Recv <CR>
Send Line Term
Send End
Break
Turna round Cha r
Modem Control
Send ACK
Send Region
Alt Input Data
Disconnect
Send Null Suppress Ignore CTS
F8
F9
Print
Prnt Line Term
Prnt Mode
Indep Pass Thru
Prnt Block Term
Secondary Recv
Prnt Region
Print Chars
Em ulation
Attribute
Page Edit
WPRT Underline
Save Labels
Bright Video
WPRT Intensity
WPRT Blink
Char Set
Fkey Speed
WPRT Reverse
Display NV Labels
Status Line
Enhanced Attributes WP-Graphics
Set Control
Force Insert
Em ulation
Em ulation
Num eric Kpd
Status Line
WP-Graphics
Cursor Kpd
ANSI-ID
Function Key Lock
Send Data
Char Set
Feature Lock
Char Set
Force Insert
Statis Lom e
Set Control
WP Graphics
F10
Tabs
Auto Init Tabs
Answerback Mode
Key
Default Tabs
Answerback Conceal
Program
Tab
F11
Answerback
Program
Execute
F12
Key Dir
PrtSc
Save Term inal
Save Session
Reset Term inal
Clear Screen
Recall Term inal
Recall Session
Reset Session
Default Term inal
Default Session
Reset Ports
Default Session UDKs
Pause
or
Exit Setup
Save all param eters? (Y/ N)
Ctrl-Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
32
Setup
QUICK: F1
F1
Quick
F2
Genrl
F3
Disp
F4
Kybd
F5
Keys
F6
Ports
F7
Host
F8
P rint
F9
Em u l
F10
Tabs
F11
AnsBk
F12
Prog
P rint
Exec
Parameters
Emulation=IBM 3151
EIA Baud Rate=9600
Aux Baud Rate=9600
Language=U.S.
EIA Data Format=8/ 1/ N
Aux Data Format=8/ 1/ N
Sessions=One
Enhance=On
Com m Mode=Full Duplex
Host/ Printer=EIA/ Para
Choices
ADDS VP
VT2 0 0 / 8
Wyse 60
VT1 0 0
Wyse 50+
SCO Console
PC Term
VT3 0 0 / 7
IBM 3151
VT3 0 0 / 8
TVI 9 2 5
VT2 0 0 / 7
AT3 8 6
Select
Enter/ S-Enter : Next/ Prev Choice
Exit : Setup Key
•
®
¯ ¬ : Parameter
Em ulation: [ADDS VP, Wyse 60, Wyse 50+, PC Term , VT300/ 8, VT300/ 7,
VT200/ 8, VT200/ 7, VT100, IBM 3151, SCO Console, AT386, TVI 925]
Select the “personality” of the terminal (the way in which it responds to commands).
Note that SCO Console and AT386 emulations are not available with the ANSI
keyboard. If you are using PC-Term emulation, refer to the Local Leadin selection in
the Keys: F5 section for access to local “hot keys.”
All associated defaults are loaded when the emulation is changed. Defult choices
are in bold. Some defaults may vary depending on the selected emultion.
Com m Mode: [Full Duplex, Half Duplex, Full Block, Half Block]
Select the method of communication to match the host computer.
EIA Baud Rate : [110, 150, 300, 600, 1200, 1800, 2000, 2400, 4800, 9600,
19200, 38400, 57600, 76800, 115200, 134400]
Select the number of bits communicated per second to match the speed at which the
primary host or printer expects to communicate.
Aux Baud Rate : [110, 134.5, 150, 300, 600, 1200, 1800, 2000, 2400, 4800,
9600, 19200, 38400]
The speed at which the secondary host or printer expects to communicate.
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL: F2
33
Enhanced: [On, Off]
Normally, the terminal responds to a set of commands that correspond to the
emulation selected. When Enhanced mode is on, the set of commands is extended to
those printed in boldface in the Programming chapter.
EIA Data Form at: [7/ 1/ N, 7/ 1/ O, 7/ 1/ E, 7/ 1/ M, 7/ 1/ S, 7/ 2/ N, 7/ 2/ O, 7/ 2/ E,
7/ 2/ M, 7/ 2/ S, 8/ 1/ N, 8/ 1/ O, 8/ 1/ E, 8/ 1/ M, 8/ 1/ S, 8/ 2/ N, 8/ 2/ O, 8/ 2/ E, 8/ 2/ M,
8/ 2/ S]
Select a data bits/ stop bits/ parity combination which matches the data format of the
primary host or printer. Parity abbreviations are: O = odd, E = even, S = space, M =
mark, and N = none.
AUX Data Format: [7/ 1/ O, 7/ 1/ E, 7/ 1/ M, 7/ 1/ S, 7/ 2/ N, 7/ 2/ O, 7/ 2/ E, 7/ 2/ M,
7/ 2/ S, 8/ 1/ N, 8/ 1/ O, 8/ 1/ E, 8/ 1/ M, 8/ 1/ S, 8/ 2/ N]
Select a data bits/ parity bits/ stop combination which matches the data format of the
secondary host or printer. Parity abbreviations are: O = odd, E = even, S = space, M
= mark, and N = none.
La ngua ge : [U. S., U.K., Danish, Finnish, French, Germ an, Norwegian,
Portuguese, Spanish, Brazilian, Swedish, Dutch, Belgian-Flem ish, Fr-Canadian,
Italian, Latin Am erican, Swiss-French, Swiss-Germ an, Turkish, Greek, Hungarian,
Czech, Slovak, Polish, Rum anian, Slovenian, Croatian, Bosnian, Serbian Latin,
Russian, Hebrew]
Select the language type which matches your keyboard’s layout.
La ngua ge : [U.S. , U.K., Danish, Dutch, Finnish, Belgian-Flem ish, French,
Fr-Canadian, Germ an, Italian, Norwegian, Spanish, Swedish, Swiss-Germ a n
Swiss-French, Turkish]
Select the language type which matches your keyboard’s layout.
Sessions: [One, Two]
Select the number of sessions that the terminal will run. One session is required per
connection to a host. When two sessions are selected, the Setup menu will display the
message “Press Ctrl-Enter (Kpd) to Toggle Sessions” at the bottom of the screen. The
current session is displayed at the upper left corner of the status line (either by a SES1
or SES2 indicator). To change the active session, press Ctrl and Enter (on the numeric
keypad) simultaneously.
Hos t/ P rinter: [EIA/ Aux, EIA/ Para , EIA/ None, Aux/ EIA, Aux/ Para, Aux/ None,
None/ EIA, None/ Aux, None/ Para, None/ None]
The first part of the selection indicates the host (either the EIA port or the AUX port)
and the second part of the selection indicates the printer port (if a serial printer is used,
either the EIA or Aux port can be used to connect to the printer, but if a parallel
printer is being used, the PAR port should be used.) The active session “drives” the
printer. EIA/ Para is the default for session 1, and Aux/ None is the default for session
2.
GENERAL: F2
This chapter lists all possible parameters for each menu, and all possibe choices for
each parameter. Depending on the emulation selected, and the key mode (ASCII or
ScanCode), Setup will only present the valid set of parameters and chices in each
menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
34
Setup
Em ulation: Select the “personality” of the terminal. See the Quick menu earlier in
this chapter.
Enhance d: Choose whether the terminal can respond to commands beyond the
limitations of the current emulation. See the Quick menu earlier in this chapter.
Auto Wrap: [On, Off]
Select whether the cursor drops to the next line when it reaches the right margin or
continues to display characters at the right margin. In ANSI emulations, the default is
off.
Auto Font Load: [On, Off]
Select whether the four font banks (0-3) should automatically be loaded when screen
size or the emulation is changed.
Auto P age : [On, Off]
When the cursor is moved off the page using a command that includes scroll and Auto
Page mode is on, the screen displays the new page. These pages are numbered from 0 to
a maximum of 9. When on, Auto Page will track the page even if Auto Scroll is off. The
up-arrow key does not have a scroll command embedded, so it cannot be used to view
the previous page even when Auto Page is on.
Auto Scroll: [On, Off]
Choose whether the terminal updates the display when the cursor is moved beyond the
boundaries of the currently viewed screen.
Monitor Mode : [On, Off]
Choose whether control codes will be displayed as their graphic representations or be
acted upon as terminal/ cursor commands.
Screen Saver: [Off, 2 m in, 5 m in, 15 m in, 30 m in]
Select whether the screen will go blank after lack ofactivity from the keyboard or the
host of the selected period of time. The first key typed at the keyboard when the
screen is blank will reactivate the display. The keycode will not be transmitted to the
host. The Caps Lock LED (or Lock on the ANSI keyboard) will flash while Screen
Saver is active.
Use screen saver to prevent “phosphor burn” on the screen when the display on the
terminal is left unchanged for an extended time period.
20 minutes after the screen saver is activated, Energy Star, a power saving feature, is
activated. The first key typed at the keyboard brings the energy level back up.
Be ll Volum e : [0 , 1 , 2 , 3 , 4 , 5 , 6, 7 , 8 , 9 ]
Select the bell volume from off [0] to high [9]. This will be the volume for alarm tones,
warning bells, and keyclicks.
Warning Be ll: [On, Off]
Select whether a warning bell is sounded when errors (such as an invalid compose
sequence) are encountered.
Sessions: [One, Two]
Select the number of sessions (hosts) that the terminal will run. See the Quick menu
earlier in this chapter.
Se s s ion Dis play: [Full, Split]
When two sessions are used, select whether each host’s data displays on a full screen or
if both hosts share a split screen. In either case, the way to toggle between the hosts is
by using Ctrl-Enter (num ). Both hosts can receive and update data simultaneously. The
purpose of toggling is so that keyboard entry can be directed to the selected host. In the
Download from Www.Somanuals.com. All Manuals Search And Download.
DISPLAY: F3
35
case of a full display, toggling also brings the entire display of the selected host into
view.
The selection above is not available in the IBM 3151 emulation.
Be ll Le ngth: [140 m s, 350 m s, 570 m s, 780 m s]
Denotes duration of bell sound.
Se tup Lang: [US, French, Germ an, Italian, Spanish, Portuguese]
Affects display of setup and the status lines.
Curs or Dir: [right to left, left to right]
This feature affects the direction in which the text is entered (defaults to right to left
when Hebrew language is chosen).
DIS P LAY: F3
P a ge Le ngth: [24, 25, 28, 29, 42, 43, 48, 50, 56, 58, 68, 84, 86, 96, 100, 112,
116, (168), (172), (192), (200), *24, *25, *28, *29, *42, *43]
For the IBM 3151 emulation, page length choices are 24, 25, 28, 42, 43, 48,
50.
Select the number of lines per page. As many as ten pages (0-9) may be available, but the
number of pages in memory depends on the number of lines per page, the type of
emulation, and whether 80-Only is selected for columns. The total lines used
(Lines/ Page x # of Pages) will not exceed 240. See Page Configurations in Appendix A.
Page lengths which are multiples of 24 or 25 and those that are multiples of 42 or 43
are displayed by default on a 26-line or 44-line screen, respectively. Page lengths which
are multiples of 28 or 29 are displayed on a 30 line screen by default. The extra one or
two lines on the screen can be used as status lines.
The selections shown in ( ) are not available in dual session mode. If a page length
which is preceded by an asterisk (*24, *25, *28, *29, *42, or *43) is selected, the total
number of pages will be two, where the first page contains the number of lines in the
selection (24, 25, 28, 29, 42, or 43) and the second page contains the remaining
allowable lines. See Page Configurations in Appendix A.
Screen Length: [26 Lines, 30 Lines, 44 Lines, 52 Lines]
Select the number of lines that can be displayed on the screen at one time. The page
length affects the default screen length.
Screen Video: [Norm a l, Reverse]
Choose between bright characters on a dark background (normal) and dark characters
on a bright background (reverse). In reverse video mode only, the “Enhanced
Attributes” parameter is available. See General:F2 section for more details.
Dis play Curs or: [On, Off]
Choose whether the cursor will be displayed.
Cursor: [Blink Block, Steady Block, Blink Line, Steady Line]
Choose the appearance of the cursor.
Auto Adjus t Curs or: [On, Off]
Select whether the screen attempts to follow the cursor down the page by scrolling just
enough to keep the cursor in view.
Download from Www.Somanuals.com. All Manuals Search And Download.
36
Setup
Colum ns : [80, 132, 80-Only]
Choose the number of columns that the screen can display. 80-Only provides more
pages in memory for a given page length by disallowing changes to 132-column
display.
Wid th Cha nge Cle a r: [On, Off]
Select whether the screen is to be cleared when the number of columns on the screen is
changed from 80 to 132 or vice versa.
Changing columns from/ to 80-only forces the screen to clear indepedent of Width
Change Clear.
Speed: [Fast, Norm al]
Selecting “fast” improves the speed at which screen display occurs at the expense of
minor, temporary distortion of text called “tearing.”
Scroll: [Sm ooth 1 , Sm ooth 2 , Sm ooth 4 , Sm ooth 8 , Jum p]
Choose whether the data on the screen scrolls smoothly or “jumps” to accommodate
data at the rate it is received. Select the number of scan lines per second the page scrolls
up when smooth scroll is selected. Smooth 1 is the slowest rate and Smooth 8 is the
fastest.
Re fre s h Rate : [60 Hz, 71 Hz, 82 Hz, 100 Hz]
Select the rate (number of times per second) at which the image on your terminal’s
display is updated. This selection is only available in 26 line display mode.
Overscan Borders: [On, Off]
Choose whether the overscan borders are active. The borders extend video from one
edge of the screen to the next. (To see the borders, selectreverse for Screen Video.)
Viewports : [1 2 3]
Select number of viewports (up to 3 viewports can be selected on a page).
Viewport 1 Bottom Row [10]
1 through page length minus 1. This specifies the last row number of the first
viewport.
This parameter displays in Setup when number of viewports is greater than 1.
Download from Www.Somanuals.com. All Manuals Search And Download.
KEYBOARD: F4
37
Viewport 2 Bottom Row [20]
2 through page length minus 1. This specifies the last row number of the second
viewport.
This parameter displays in Setup when number of viewports is greatethan 2.
P a ge s [1-8]
Select the number of pages the user can access. The maximum number of pages is
dependent on the page length. The number of pages is defaulted to 1 whenever the
page length or columns is changed. The page selection will not display when viewports
is greater than 1.
KEYBOARD: F4
La ngua ge : [U.S. , U.K., Danish, Finnish, French, Germ an, Norwegian,
Portuguese, Spanish, Brazilian, Swedish, Dutch, Belgian-Flem ish, Fr-Canadian,
Italian, Latin Am erican, Swiss-French, Swiss-Germ an, Turkish, Greek, Hungarian,
Czech, Slovak, Polish, Rum anian, Slovenia n, Croatian, Bosnian, Serbian Latin,
Russian, Hebrew]
Select the language type which matches your keyboard’s layout.
La ngua ge : [U.S. , U.K., Danish, Dutch, Finnish, Belgian-Flem ish, French,
Fr-Canadian, Germ an, Italian, Norwegian, Spanish, Swedish, Swiss-Germ an
Swiss-French, Turkish]
Select the language type which matches your keyboard’s layout.
Char Set Mode: [PC, ANSI, ASCII]
Choose which NRC set to use. This selection is only available in National Mode and
foreign languages. In VT emulations, the default isANSI. To determine which sets are
loaded for each mode, refer to the 3153 Programmer’s Reference Guide.
Ke y Mode : [ASCII, ScanCode]
Select whether keys transmit ASCII codes or the ScanCode. The ScanCode transmits a
“make code” when a key is pressed and a “break code” upon its release. When
ScanCode is selected, “Comm Mode” is forced to Full Duplex and “Character Set” is
forced to Multinational (8-bit).
Keyclick : [On, Off]
Choose whether pressing a key results in a clicking sound. The default is off in SCO
Console emulation and IBM 3151.
Ke y Re pe a t: [On, Off]
Choose whether keys, including function keys, will repeat when pressed for more than
half a second. This setting does not affect the following keys on the PC-style
keyboards: Caps Lock, Scroll Lock, Num Lock, Shift keys, Ctrl keys, Alt keys,
Return, Print Screen, Pause. On the ANSI keyboard, the following keys are
unaffected: Lock, F1–F5, Shift keys, Control, Compose, and Return.
Ke y Ra te : [15 cps, 20 cps, 30 cps]
When “Key Repeat” is on, a key that is pressed for more than half a second will
automatically repeat. This selection allows you to choose the number of characters that
are generated per second when a key is auto repeating.
Download from Www.Somanuals.com. All Manuals Search And Download.
38
Setup
Ke yboard Layout: [Q, F]
This selection is only available when Turkish keyboard is selected. Q and F refer to the
two Turkish keyboard layouts available. Q and F correspond to the top left key on the
alphanumeric keypad.
Margin Be ll: [On, Off]
Choose whether a bell tone sounds when the cursor is nine positions away from the
right margin.
Ke y Lock: [Caps, Reverse, Shift]
Affects the state of alphanumeric keys when Caps-Lock is engaged.
§
§
§
Caps causes alphabetic keys to be uppercase regardless of the shift key.
Reverse causes the shift key to generate lowercase alphabetic keys.
Shift causes all alphanumeric keys to be generated as uppercase (or shifted, in the
case of numbers). If the Shift key is pressed, while Shift is selected, Caps-Lock
will be disengaged.
Caps Lock: [Toggle, Always On, Always Off]
This setting effects the state of the Caps Lock key. When set to always on or always off
the key has no effect. When set to toggle, the terminal will power on in the off mode
and pressing the key will alternate between the off mode and the on mode.
Num Lock: [Toggle, Always On, Always Off]
This setting effects the state of the Num Lock key. When set to always on or always off
the key has no effect. When set to toggle, the terminal will power on in the off mode
and pressing the key will alternate between the off mode and the on mode.
Cod e P a ge : [DEC Multi, PC 437, PC 850, PC 852, PC 857, PC 860, PC 861, PC
862, PC 863, PC 865, PC 866, PC 869, ISO-1, ISO-2, ISO-5, ISO-Hebrew,
ISO-Cyrillic, ISO-Greek]
This selection is only available in 8-bit emulations in Multinational M ode. The default
code page is based upon language and emulation selected. To determine which sets are
loaded for each code page, refer to the 3153 Programmer’s Reference Guide.
KEYS : F5
Return Key: [CR, CR-LF, TAB]
Select the code the return key on the main alphanumeric keypad transmits.
Enter Key: [CR, CR-LF, TAB]
Select the code the enter key in the numeric keypad transmits.
Alt Key (left): [Meta, Com pose, Funct, Scroll-Lock, Alt Key]
Select the way in which the left ALT key (or the Compose key on the ANSI keyboard)
behaves. The Alt Key selection refers to the right Alt key.
§
§
§
Meta – sets the most significant bit for the next character and allows 8-bit data to
be generated from the keyboard.
Com pose – precedes sequences of keys to create a character thatis not on the
keyboard but is available in the active character set.
Scroll Lock – causes the Alt key to function as the Scroll Lock key, and is a toggle
to hold/ free data on the screen. It requires the use of flow control for the host
port Rcv Prtcl.
§
§
Funct – causes the Alt key to function as the Funct key on an ASCII keyboard.
Alt Key – causes the left Alt key to behave identically to the right Alt key.
Download from Www.Somanuals.com. All Manuals Search And Download.
KEYS: F5
39
P ound Ke y: [U.S. , British]
Choose the character transmitted for 23h—the US pound (# ) or the British pound (£).
Re turn Ke y Re pe at: [On, Off]
Select whether the Return key located on the alphanumeric keypad will repeat when
held down for more than half a second (only selectable when “Key Repeat” = On).
Download from Www.Somanuals.com. All Manuals Search And Download.
40
Setup
Return Key: [Field, New Line]
When the Return Key =New Line, the functions specified in the New Line parameter are
performed. When the Return Key = Field, the functions specified in the New Line
parameter are performed unless the target line is within a protected field. The cursor
will then move to the first character position of the next unprotected field.
Enter Key: [Send, Return]
The Enter Key can be defined to be either a Send or Return Key.
Ne w Line : [<CR>, <CR><LF>]
This parameter specifies the codes generated when the return key is pressed.
Send Key: [P a ge, Line]
The contents of the current page is sent to the host when the Send Key is pressed and
Send Key is selected for page. The Contents of the current line is sent to the host when
the Send Key is pressed and Send Key is selected for line.
Ins ert Character: [Mode, Space]
§
§
Mode – enters insert mode when the insert key is pressed.
Space – a space character is inserted at the current cursor position when the insert
key is pressed.
Loca l Le a d in: [On, Off]
This parameter is only available when Key Mode (in the Kybd menu) is ScanCode. If
Local Leadin is off, the only local function, shown in Appendix A, that is available is
Ctrl-Scroll Lock (Ctrl-Select on the ANSI keyboard) to enter Setup. If Local Leadin is
on, the Setup keystroke “introduces” the keystroke as local and then local functions can
be generated using the keystrokes listed in Appendix A. For example, to enter Setup
when ScanCode and Local Leadin are on, press Ctrl-Scroll Lock to introduce this as a
local function (“LEAD” will appear in the status line), and then Ctrl-Scroll Lock (Ctrl-
Select on the ANSI keyboard) to enter Setup.
Local Leadin will not work if Comm Mode is set to Half Block or Ful Block.
The following selections apply to the PC-style keyboards:
Dis connect: [Disa bled, Pause, Alt-Pause]
Select the keystroke that will generate a modem disconnect.
Backs pace: [BS/ DEL, DEL/ BS, DEL/ CAN, BS/ BS]
Choose the codes sent by the backspace key in the normal/ shifted positions.
Desk Acc: [Ctrl ¬ , Disabled]
Select how the DeskAccessories can be accessed. This selection does not appear when
SCO Console emulation is selected. In SCO Console emulation, Ctrl ¬ is the only
access method.
The default allows the desk accessories to be accessed through a menu which appears
when Ctrl and the left arrow key are pressed simultaneously. This brings up a pop-up
Download from Www.Somanuals.com. All Manuals Search And Download.
KEYS: F5
41
window; selections for the specific accessory can be made from that menu by pressing
F1-F5. The Sh-Ctrl-Fkeys option, when selected, allows direct access to desk
accessories (bypassing the menu) by pressing Sh-Ctrl-F1 through Sh-Ctrl-F5 . Selecting
Disabled will inhibit entry to desk accessories. Once a desk accessory is displayed, any
other desk accessory can be accessed by pressing only the function key associated with
it (without pressing Sh-Ctrl).
UDKs: [Em ul Dependent, User Dependent]
Choose whether the UDKs should get defaulted when the host changes the emulation.
The following selections apply only to the ANSI keyboard:
Dis connect: [Disabled, Shift-F5]
Choose to allow the keystroke that will generate a modem disconnect on the ANSI
keyboard or to disable the Disconnect function. Note that if “F1 to F5 keys” is Fkey in
Setup, the Disconnect function will be remapped to Ctrl-Shift-F5.
F1 to F5 keys : [Loca l, Fkey]
This selection determines whether the first five keys, labeled F1–F5, serve as local
keystrokes (for example, F3 allows access to Setup) or will serve as function keys which
are loaded with the default strings. (Only reprogrammed strings are visible in the text
area for a given function or edit key; the default strings are not visible in Setup.)
If Fkey is selected, then the keystroke to enter Setup becomes Ctrl-Fon the ANSI
keyboard.
With the three remapping selections, keys which are available on a PC-style keyboard
are now available on the ANSI style keyboard: [ESC] [`~] [, and .].
The three selections should either be kept in their defaults (as they appear on the keyboard), or
all three should be changed to follow the mapping scheme described here.
`~ Key: [ a nd ~ or ESC]
`
Select the characters sent by the tic/ tilde key.
<> Key: [< a nd > or ` and ~]
Select the characters sent by the triangle bracket key in the normal and shifted
positions.
,, and .. Keys: [,, a nd .. or ,< and .>]
Select the character sent by the comma and period keys in the normal and shifted
mode.
Backs pace: [BS/ DEL, DEL/ BS, DEL/ CAN]
Choose the codes sent by the key in the normal/ shifted positions.
Com pos e Ke y: [Meta, Com pose, Funct, Scroll-Lock, Alt Ke y]
This selection indicates the role that the Compose key will play. The explanation of
choices is the same as for the Alt Key (left) selection, which is discussed earlier in this
section.
Download from Www.Somanuals.com. All Manuals Search And Download.
42
Setup
P ORTS: F6
EIA Baud Rate : [110, 150, 300, 600, 1200, 1800, 2000, 2400, 4800, 9600,
19200, 38400, 57600, 768000, 115200, 134400]
See the Quick menu earlier in this chapter.
EIA Data Form at: [7/ 1/ N, 7/ 1/ O, 7/ 1/ E, 7/ 1/ M, 7/ 1/ S, 7/ 2/ N, 7/ 2/ O, 7/ 2/ E,
7/ 2/ M, 7/ 2/ S, 8/ 1/ N, 8/ 1/ O, 8/ 1/ E, 8/ 1/ M, 8/ 1/ S, 8/ 2/ M, 8/ 2/ N, 8/ 2/ O, 8/ 2/ E,
8/ 2/ S]
See the Quick menu earlier in this chapter.
EIA (Aux) P arity Check: [On, Off]
Choose whether the parity bit will be checked. When parity check is on and the parity
bit received is inconsistent with the data received, indicating an error in
communications, an asterisk (*) 2Ah is displayed instead of the character.
Aux Baud Rate : [110, 134.5, 150, 300, 600, 1200, 1800, 2000, 2400, 4800,
9600, 19200, 38400]
See the Quick menu earlier in this chapter.
AUX Data Format: [7/ 1/ O, 7/ 1/ E, 7/ 1/ M, 7/ 1/ S, 7/ 2/ N, 7/ 2/ O, 7/ 2/ E, 7/ 2/ M,
7/ 2/ S, 8/ 1/ N, 8/ 1/ O, 8/ 1/ E, 8/ 1/ M, 8/ 1/ S, 8/ 2/ N]
See the Quick menu earlier in this chapter.
EIA (Aux) Recv: [No Protocol Xon-Xoff (XPC), Xany-Xoff (XPC), DTR (DSR),
Xany-Xoff/ DTR (DSR)]
Choose the form of flow control for data received from the primary or secondary host.
Software flow control uses Xon-Xoff DC1 (11h) and DC3 (13h). XPC is used by “Scan
Code” mode because it uses DC1 and DC3 as data. Xany-Xoff (XPC)is similar to
Xon-Xoff, except that any character transmitted to the host is treated as an Xon, so
data from the terminal is buffered, rather than being sent to the host. DTR (DSR for Aux)
relies on the hardware signal DTR or DSR (pin 20 or pin 6) from the device.
Xany-Xoff/DTR (DSR) uses software and hardware flow control.
Flow control is recommended to protect against data loss.
EIA (Aux) Xmit: [No Protocol, Xon-Xoff, DSR (DTR), Both]
This is similar to “EIA (Aux) Recv,” except that it applies to the data transmitted
from the terminal to the primary or secondary host or printer. DSR is the hardware
signal for Data Set Ready (pin 6).
In ADDSÔ VP emulation and WP Graphics mode DC1 and DC3 can be
interpreted as data and should not be selected as a form of Protocol.
EIA (Aux) Xmt Pace: [Ba ud , 35 cps, 60 cps, 150 cps]
Define the maximum number of characters per second that the terminal can transmit.
When a characters limit (35 cps, 60 cps, or 135 cps) is set, the delays are averaged
between characters for the selected baud rate. This is also known as “pacing.” The Baud
option provides no pacing, allowing data to be transmitted at the specified baud rate.
Download from Www.Somanuals.com. All Manuals Search And Download.
HOST: F7
43
HOST: F7
Bre ak: [2 5 0 m s, 170 m s, 5 00 m s, Off]
Choose the duration of the break signal in milliseconds. This is an interruption in data
flow, and can be disabled.
Modem Control: [On, Off]
If a modem is being used to communicate with the primary or secondary host,
modem control should be on. To perform a disconnect, the terminal drops the DTR
signal. In full duplex, the terminal keeps RTS high and checks for a CD signal before
sending data to the modem. In half duplex, it raises RTS and awaits a clear-to-send
(CTS) signal from the modem before sending data.
Dis connect: [2sec, 60m s]
Select the maximum time period that the modem can be disconnected (or the modem
line be down) before the terminal performs a Modem Disconnect. This occurs if “EIA
(Aux) Modem Control” is on.
Com m Mode: [Full Duplex, Half Duplex, Full Block, Half Block]
Select the communications mode.
Half-duplex is not available when KeyMode is ScanCode.
Re ce ive <CR>: [<CR>, <CR><LF>]
Select the way in which carriage returns received will be interpreted.
Receive <DEL>: [Ignore, Destruct <BS>]
Choose to ignore the DEL control code (7Fh) when received or to treat it as a
Destructive Backspace code.
Send ACK: [Off, On ]
Decide whether the terminal should respond to inquiry (05h) or when certain terminal
functions are performed (configuring the EIA (Aux) ports, splitting screen, etc.) with
the ACK (06h) character.
Null Suppress: [On, Off]
In the default mode, the host ignores all received nulls (00 hex). When off is selected,
the terminal will accept all received nulls, and act upon them according to the selected
emulation.
Send Line Term : [<US>, <CR><LF>]
Select which line terminator is sent. <US> is 1Fh and <CR><LF> is 0Dh 0Ah.
Loca l: [Off, On]
Select whether keyed data is interpreted locally by the terminal and not sent to the
host. Data sent by the host is lost, if Local is on. The ability to print data is not affected
by this mode.
Send Block Term : [<ETX>, <CR>]
Select which character will indicate the end of a block. The choices above are for
ASCII emulations. ANSI emulations have the following choices:[None, FF].
Send End: [Cursor, Region]
Select whether the end is indicated by the scroll region or by the cursor location.
Se nd Re gion: [Screen , Scroll]
Download from Www.Somanuals.com. All Manuals Search And Download.
44
Setup
Choose whether the terminal sends data from the entire screen or from the scrolling
region.
Ignore CTS: [Off, On]
Ignore CTS is not displayed in IBM 3151 emulations
Line Control: [CRTS, PRTS, IPRTS]
§
§
§
PRTS* (permanent request to send) – PRTS handles the CTS and DSR signal as
modem signals.
IPRTS* (induced permanent request to send) – IPRTS handles the CTS and DSR
signals as if the signals are always on.
CRTS* (controlled request to send) – CRTS looks at the CTS, DSR and CD signals
to determine when the terminal can send or receive data.
* PRTS and IPRTS require full duplex communication capabilities.
CRTS requires half duplex communication capabilities.
Turnaround Char: [<ETX>, <CR>, <EOT>, <DC3>]
The line turnaround character is attached to the end of a data stream when one of the
read commands is received or one of the following keys is pressed:
Send
Send Line
Clear
F1 thru F36
PA1 thru PA3
Sn Msg
Reset (if reset attn is enabled)
Print (if print key attn is enabled)
Print line (if print key attn is enabled)
Print Msg (if print key attn is enabled
Send Null Suppress: [Off, On]
§
§
Off – Trailing null characters are converted to space characters when data is sent to
the host system.
On – Trailing null characters are removed when data is sent to the host system.
P RINT: F8
P rint Mode: [Norm a l, Auto, Controller]
Select the way in which printing is controlled.
§
§
§
Normal – indicates that printing is to occur when a print request (such as print
screen) is received.
Auto – prints a line when the terminal receives a LF, a FF, or a VT code, or when
autowrap occurs.
Controlle r – indicates that host data is sent to the printer (pass through mode).
Printing is controlled by the host computer.
P rint Block Term : [<ETX>, <CR>]
Select the character which indicates to the printer that the block of data to be printed
has ended. The options above are for ASCII emulations. In ANSI emulations, the
choices are [None, <FF>].
Download from Www.Somanuals.com. All Manuals Search And Download.
EMULATION: F9
45
P rint: [National, Line Drawing, Multinational]
Choose the set of characters used when printing.
P rint Re gion: [Screen , Scroll]
Indicate the region of the screen that is to be printed: the entire screen or a certain
section of it called the scrolling region. A scrolling region is a limited portion of the
screen which applications (such as word processors) may designate to be the user’s
region.
P rint Line Term : [<US>, <CR><LF>]
Indicate the character that <R> is to terminate a line of print.
Secondary Recv: [Off, On]
When “on,” data received from the serial printer is routed to the port assigned for the
host. This data is not displayed on the screen, and is transparent to the user. When
“off,” data received from the printer port is ignored.
Independent P as s Thru: [Off, On]
When independent pass-through printing is enabled, the host system can concurrently
send data to the terminal and to the printer. When a low speed printer is attached to
the terminal, it allows print operations to continue without suspending normal
terminal operations.
EMULATION: F9
The parameters displayed in this menu depend upon the current emulation. This
section is divided between parameters for ASCII and ANSI emulations.
ASCII Em ulations
P a ge Edit: [Off, On]
When page edit is on, edit features such as insert act upon text to the end of the current
page.
WP RT Intens ity: [Dim , Norm al, Suppress]
Choose the intensity of write protected characters . Suppress indicates that the
character’s foreground is the same as its background with the effect of “suppressing”
output.
WP RT Unde rline : [Off, On]
Choose whether write-protected characters are underlined.
WP RT Blink: [Off, On]
Choose whether write-protected characters blink.
WP RT Revers e: [Off, On]
Choose whether write-protected characters display in reverse video.
Fke y Spe e d: [Fa s t, Norm a l]
Selects the speed at which function keys and labels are programmed by the host. Fast
mode will increase the speed for Wyse 50 compatibility, but will limit the amount of
space in each function key and answerback message to 8 bytes. Edit keys are not
Download from Www.Somanuals.com. All Manuals Search And Download.
46
Setup
available for programming in fast mode. Changing this selection will default all
function keys, edit keys, and function keys labels.
Download from Www.Somanuals.com. All Manuals Search And Download.
EMULATION: F9
47
Save Labe ls : [Off, On]
When on, labels that are downloaded by the host will be saved in non-volatile memory.
If this selection and Display NV Labels are off, labels written by the host would be lost
upon entry and exit to Setup.
Attribute: [Cha r, Line, Page]
Choose the extent to which attributes are propagated. (The only parallel ASCII
emulations are PC Term and Wyse 60.)
Dis play NV Labels : [On, Off]
Select whether the labels in non-volatile memory are displayed on the lowest line.
When off is selected, any existing labels will remain on the screen, until on is selected,
and they are re-displayed. On a 26-line screen, they are displayed below line 24. On a
44-line screen, labels are displayed below line 42, and on a 52-line screen, they are
displayed below line 50. (The top line is the top status line and cannot be used for
data.) If the page length used is a multiple of 25 (instead of 24) and the screen length is
26 lines , then the last data line is used for data and labels will not be displayed
regardless of this setting. The same is true for a page length that is a multiple of 43
(instead of 42) with a screen length of 44 lines.
Status Line : [Standard, Extended, Off]
Select the type of the status line. In standard, cursor row and column, session indicator,
print indicator, Caps Lock, and communications mode are displayed. In extended, only
session indicator, Caps Lock, communications mode, protect and write protect are
displayed.
Char Set: [National, Multinational]
Select whether the character set used is the 7-bit national chart or the 8-bit
multinational chart when Language is not U.S. If U.S. is chosen, the character set is
multinational.
Enhanced Attributes : [Off, On]
When set to on, gives a better display presentation in overscan and reverse video
modes. The blink and dim video attributes will affect the foreground text instead of
the background. This selection is only available in reverse video mode, on a
per-session basis, and is disabled in a “split” display screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
48
Setup
Bright Vide o: [Off, Mode 1, Mode 2]
Provides a brighter display when set to Mode 1 or Mode 2. In Mode 1, both normal
and dim text are brighter than in the standard mode. In Mode 2, only normal text is
brighter, resulting in a greater contrast between normal and dim text.
This parameter setting affects both sessions, but will not affect an ANSI emulation
in the inactive session.
WP -Graphics: [Off, On]
Selects whether Word Perfect Graphics commands are processed or ignored.
ANSI Em ulations
Numeric Kpd: [Num eric, Application]
Choose the set of strings sent by the numeric keypad.
Curs or Kpd: [Cursor, Application]
Choose the set of strings sent by the cursor control keypad.
Se nd Data: [All, Erasable]
Choose whether the data sent to the host is all data (erasable and selectively erasable) or
only those characters tagged as erasable.
ANSI-ID: [VT100, VT101, VT102, VT220, VT320]
Select the terminal’s identification.
Function Ke y Lock: [Off, On]
Select whether the function keys are locked or modifiable by the host.
Ke y Us age : [Typewriter, Data Process]
This selection is available for all language selections except U.S. It applies to keys that
have two characters printed side-by-side to select which character is sent by that key.
Typewriter selects the character printed on the left side while Data Process selects the
character printed on the right side of the keycap.
Char Set: [Multinational, National]
Select whether the character set used is from the 7-bit national chart or the 8-bit
multinational chart. The default is the 8-bit multinational character set except when
the emulation is VT100.
Fe ature Lock: [Off, On]
When on, the host cannot change user features: key repeat, scroll speed, screen
background, tab stops, and keyboard lock.
Status Line : [Off, Indicator, Host-Write, Both]
Specify the way in which the status line is to be used: for host messages [host-write], as
a cursor position indicator [indicator], for [both] or off.
IBM Em ulation
Forcing Insert: [Off, Line, Character, Both]
§
Off – If there is no room to insert a character or line, the insert operation will not
be performed.
§
Line – If there is no room to insert a null line and an insert line operation is
requested, the current line is replaced with a null line and the remaining lower
Download from Www.Somanuals.com. All Manuals Search And Download.
EMULATION: F9
49
lines and the previous current line moves down one line. The bottom line is then
discarded.
§
§
Characte r – If there is no space to insert a character and an insert character
operation is requested, a character can be inserted at the cursor position.
However, the last character of the current line is discarded when the line wrap
parameters is off, or the last character of the page (or field in a formatted page) is
discarded when line wrap is on.
Both – Enables the line and character functions
Se t Control: [Tem porary, Perm anent]
§
Temporary – Set Control commands do not replace the values stored in
NVRAM. Only the working setup parameters are modified.
§
P e rm ane nt – The Set Control commands update both the working setup
parameters as well as the NV setup parameters.
Status Line : [Off, Indicator, Host-Write, Both]
Specify the way in which the status line is to be used: for host messages [host-write], as
a cursor position indicator [indicator], for [both] or off.
Char Set: [Multinational, National]
Select whether the character set used is from the 7-bit national chart or the 8-bit
multinational chart. The default is the 8-bit multinational character set except when
the emulation is VT100.
WP -Graphics: [Off, On]
Selects whether Word Perfect Graphics commands are processed or ignored.
Download from Www.Somanuals.com. All Manuals Search And Download.
50
Setup
TABS: F1 0
F1
Quick
F2
Genrl
F3
Displ
F4
Kybd
F5
Keys
F6
Ports
F7
Host
F8
P rint
F9
Em u l
F10
Tabs
F11
AnsBk
F12
Prog
P rint
Exec
Parameters
Auto Init Tabs
=
Off
Default Tabs
Tab=Field
10
20
30
40
50
60
....:....¯....:....¯....:....¯....:....¯....:....¯....:....¯....:.
70
80
90
100
110
120
130
...• ....:....• ....:....• ....:....• ....:....• ....:....• ....:....• ..
Choices
Off
On
Select
Enter/ S-Enter : Next/ Prev Choice
Exit : Setup Key
•
®
¯ ¬ : Parameter
Auto Init Tabs : [On, Off]
When on, tab settings will always be defaulted at power up.
De fault Tabs : This action field sets tabs at every eighth column starting at column 9.
When the cursor is placed in the Tab Map, the keys below will appear in the Choices
field:
§
§
§
§
<Space> – clear the current tab setting.
<Shift> <Backspace> – clear all tab settings.
<T or t> – set a tab at the current location.
< • ® ¯ ¬ > – move cursor on the Tab map or back to a Parameter field
above the map.
Tab: [Field, Colum n]
§
§
Field – On a formatted page, the tab stops are defined by the field attribute
characters displayed on the screen.
Colum n – The column tab stops are used while ignoring the field attribute
characters.
Download from Www.Somanuals.com. All Manuals Search And Download.
ANSWERBACK: F11
51
ANS WERBACK: F1 1
F1
Quick
F2
Genrl
F3
Displ
F4
Kybd
F5
Keys
F6
Ports
F7
Host
F8
P rint
F9
Em u l
F10
Tabs
F11
AnsBk
F12
Prog
P rint
Exec
Parameters
Answerback Mode
=
Off
Anwerback Conceal
Answerback Message:____________________________________
Bytes Remaining: 0542
Choices
Off
On
Select
Enter/ S-Enter : Next/ Prev Choice
Exit: Setup Key
•
®
¯ ¬ : Parameter
Ans werback Mode: [On, Off]
Choose whether the answerback message (which is sent to the host at terminal reset or
power up) mode is on. This can be used to log-in to the system.
Ans werback Conceal: This is an action parameter which displays “Concealed” at the
answerback edit field. Once it is concealed, the message cannot be redisplayed. This is
a security measure for those who use answerback to send their login names and
passwords to the host.
Ans werback Mes s age: This is a 30-character field which can be edited. (See the Edit
Fields section later in thischapter.)
When “Fkey Speed” is Fast in the Emul (F9) menu, the answerback edit field
is limited to 8 bytes.
Download from Www.Somanuals.com. All Manuals Search And Download.
52
Setup
P ROGRAM: F1 2
F1
Quick
F2
Genrl
F3
Displ
F4
Kybd
F5
Keys
F6
Ports
F7
Host
F8
P rint
F9
Em u l
F10
Tabs
F11
AnsBk
F12
Prog
P rint
Exec
Param eters
Keys
=
F1
Program
=
FKey
Key Dir = Host
Text: _________________________________________________________________________
_________________________________________________________________________
_________________________________________________________________________
_________________________________________________________________________
Label: _______________
Bytes Remaining: 0542
Choices
F1
F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12
Select
Enter/ S-Enter : Next/ Prev Choice
Exit: Setup Key
•
®
¯ ¬ : Parameter
P rogram: [FKey, Sh-FKey, Ctrl-Fkey, Ctrl-Sh-Fkey, Edit Key, Sh-Edit Key]
Specify the type of key to be programmed—function or edit key in its normal or
shifted state.
When Fkey Speed is Fast in the EMUL (F9) menu, the Program options are
F/ Key and Sh-F/ Key.
Key Dir: [Com m Depend, Host, Printer, Printer & Host, Screen, Host & Screen,
Printer & Screen, All]
Select the destination of the contents of the function or edit key. Comm Dependent will
cause the direction of the key data to correspond to the “Comm Mode” of the current
session. For example, if the “Comm Mode” is Full Block, the contents of the key will be
channeled to the screen only. If it were Full Duplex, then the contents would be sent to
the host only.
Text: An edit field which permits up to 255 characters. Once the overall text limit (up
to 542 characters) is reached, the terminal will beep and accept no more text. If the
text isdeleted with the backspace key, the default code is no longer programmed.
Shift-Backspace will restore the default. See the Edit Fields section or “Fkey Speed”
in the Emulation section.
Download from Www.Somanuals.com. All Manuals Search And Download.
PROGRAM: F12
53
La b e l: A label of up to 7 characters can be entered for function keys in ASCII
emulations only. See “Display NV Labels” in the Emulation section.
<Backspace> – delete
<Shift> <Back> – default field
Key: Select the key to be programmed. The keys that are listed as choices depend upon
the Program parameter as shown below:
The following choices apply for non-SCO Console emulations:
When a PC-style keyboard is attached, the choices are:
When Program = F/Key, Sh-F/Key, Ctrl-FKey, or Ctrl-Sh-Fkey the choices are [F1 ,
F2 , F3 , F4 , F5 , F6 , F7 , F8 F9 , F1 0 , F1 1 , F1 2 ].
When Program = Edit Key or Sh-Edit Key, the choices are
[Tab, Esc, Backspace, Delete, Return, Hom e, • , ¯, ¬ , ® , EnterKpd, Insert,
PageDown, PageUp, End, and Print].
When an ANSI keyboard is attached, the choices are:
When Program = F/Key or Sh-F/Key, the choices are [F1, F2 , F3 , F4 , F5 , F6 , F7 ,
F8 , F9 , F1 0 , F1 1 , F1 2 , F1 3 , F1 4 , Help, Do, F1 7 , F1 8 , F1 9 , F2 0 ].
When Program = Edit Key or Sh-Edit key, the choices are
[Tab, <X],Select, Return, • , ¯, ¬ , ® , Enter, Next Screen, Rem ove, PF1, PF2,
PF3, PF4].
When Program = Edit Key or Sh-Edit Key, the choices are [Tab, Esc,
Backspace, Return, Print, Enter Kpd, • , ¯, ¬ , ® , Insert, Delete, Hom e, BackTab,
Clear, and ErEOF.]
To program an ESC (escape) character into the key text, press Ctrl-[.
To program a DEL character into the text field, press Ctrl-Sh-8 (alphanumeric key).
To program a carriage return or line feed into the key text field, press trl-M or Ctrl-J,
respectively.
To program the “Print Screen” key to perform a local print screen (pge) function:
In the key text field, press
Ctrl-[ and then P. Next, set the “Key Dir”=Screen option.
Download from Www.Somanuals.com. All Manuals Search And Download.
54
Setup
EXECUTE: P rnt Sc
F1
Quick
F2
Genrl
F3
Displ
F4
Kybd
F5
Keys
F6
Ports
F7
Host
F8
P rint
F9
Em u l
F10
Tabs
F11
AnsBk
F12
Prog
P rint
Exec
Parameters
Save Terminal
Save Session
Reset Terminal
Clear Screen
Recall Term inal
Recall Session
Reset Session
Default Term inal
Default Session
Reset Ports
Default Session UDKs
Choices
User Enter Key to Execute Action
¯ ¬ : Param eter
Select
Enter/ S-Enter : Next/ Prev Choice
Exit : Setup Key
•
®
All of the parameters in this menu are action parameters.
Term inal parameters affect all settings, including the emulation. Session choices affect
only settings that relate to the chosen session. In dual session (host) mode, there are two
independent sets of session parameters (Session 1 and Session 2). To toggle between
sessions, use the Ctrl-Enter (Num ) keystroke.
Save Term inal: Save all settings in non-volatile (permanent) memory, including those
associated with the session selected.
Res et Term inal: All terminal parameters are initialized. It also performs reset pages
and default modes.
Re call Te rm inal: Revert to all terminal and session settings that were saved in
nonvolatile memory. A “Reset Term inal” is also performed. This is referred to as a
hard reset and is equivalent to turning the terminal off and back on.
De fault Te rm inal: Load all defaults for the terminal and session, including the
emulation. A “Reset Terminal” is also performed.
Save Se s s ion: Save all the settings associated with the chosen session.
Res et Ses s ion: Initialize all session settings. This is also referred to as a “Soft-Reset.”
Perform page-resets and default modes. “Mode” specifies the parameters used by a
session which are not selectable through Setup such as Insert-Mode, Split-Screen, and
Graphics-Mode.
Re call Se s s ion: Load the previously saved settings associated with the chosen session.
A “Reset Session” is also performed.
De fault Se s s ion: Load all defaults associated with the session selected.
Res et P orts : Clear the transmit buffers for the host and printer port, and receive buffer
for the host port. Unlocks the keyboard and clears its buffer data.
Clear Screen: Clear the screen and the entire page.
Default Ses s ion UDKS: Set the contents of all the function and edit keys associated
with the chosen session to their factory default states.
Download from Www.Somanuals.com. All Manuals Search And Download.
Edit Fields
55
Edit Fields
Setup uses overwrite mode in text editing fields. That is, the cursor keys cannot be
used to move to a location in the text to insert characters. Upon entry to a text field,
the cursor is placed at the last text location. Use the following keystrokes:
Backspace – Move cursor left by deleting that character.
Shift-Backspace – Reset the field to its default value.
Alphanum eric keys – enter text in the normal, shifted, or control state. To generate a
control character (00h-1Fh) add 40h and use Ctrl with the character in the new
position (40h-5Fh). For example, to insert CR-LF (0Dh, 0Ah) codes, press Ctrl-M,
Ctrl-J (4Dh, 4Ah). The compose and meta functions can also be used to generate
8-bit characters.
Download from Www.Somanuals.com. All Manuals Search And Download.
56
Setup
Glossary of Terms
Some of the terms that are used in the Exec (PrtSc) menu are defined below.
Term inal Param eters
Terminal parameters includes session parameters (defined later) and non-session
parameters that affect the terminal globally without regard to the session. The
non-session parameters and their defaults are listed below:
Setup P aram eters : Bell Volume (6), Screen Saver (5 min), Overscan Borders (on),
Language (U.S.), Keyclick (on), EIA(Aux) Baud Rate (9600), EIA (Aux) Data
Format (8/ 1/ N), EIA (Aux) Parity Check (off), EIA(Aux) Rcv Prtcl
(Xon-Xoff/ XPC), EIA (Aux) Xmit Prtcl (none), EIA (Aux) Break (250 ms), EIA
(Aux) Xmit Pace (baud), EIA (Aux) Disconnect (2 sec), EIA (Aux) Modem
Control (off), Session Display (full), Screen Length (26 lines), Refresh Rate (70 Hz),
Bright Video (off), Enhanced Attributes (on), Setup Lang (U.S.), Sessions (1), Caps
Lock (Toggle), Num Lock (Toggle), Key Repeat (On), Speed (fast).
Desk Accessory Parameters: Clock Display (off), Clock Type (12 hour), Clock
Location (column 48), Date, Time (not saved) , Alarm Time (12 PM), Tone
(alarm/ hourly), Calculator (printer off, tape on), and the row and column in which
each accessory is displayed.
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary of Term s
57
Ses s ion P arameters
Session Parameters are parameters that are specific to the emulation selected in the
current session. These include three types of parameters: Setup-Edit keys, Setup, and
Modes.
Setup-Edit Keys : Function and Edit keys and the Answerback message.
Setup P aram eters : All other Setup variables that are not included in Setup
Parameters in Terminal Parameters (all global settings).
Mode P aram eters : Variables that are used by a session’s emulation, but are not
selectable through Setup. Some examples are Protect Mode, Graphics Mode, Insert
Mode, Aux Mode, Split-Screen, Transparent Mode, Character Set mappings, Setup
Language, and Sessions.
P age Res et
Page resets are executed when the session or terminal is reset or defaulted. When a page
reset is performed, it affects all pages, and the following events occur: the page is
erased, the cursor is homed, and scrolling regions are defaulted. All line attributes (such
as double-high/ wide, locked lines) are reset to normal. Split screens are cleared to a
normal, single screen and protect mode is turned off.
Download from Www.Somanuals.com. All Manuals Search And Download.
chapter
4
Desk Accessories
This terminal features five desk accessories, which can be accessed one at a time
through pop-up windows.
Overview
Desk Accessory Menu
To display this pop-up window to choose any of the five desk accessories, press Ctrl-
¬ .
Function keys F1-F5 are used to display the clock, calendar, calculator, ASCII chart,
and diagnostic menu, respectively.
To access this menu (with a PC keyboard), the selection
“Desk Acc = ¬ ” must be chosen in the KEYS (F5) Setup menu. This menu is
always available with the ANSI keyboard.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
62
Dire ct Acce s s
To display any desk accessory directly, without the desk accessory menu, the
following keystrokes are used:
§
Clock – press Ctrl-Shift-F1
§
§
§
§
Calendar – press Ctrl-Shift-F2
Calculator – press Ctrl-Shift-F3
ASCII Chart – press Ctrl-Shift-F4
Diagnostic Menu – press Ctrl-Shift-F5
You may also use a function key (F1-F5) to enter another desk accessory window,
once one is entered.
To use these keystrokes with a PC-style keyboard, the selection
“Desk Acc = Sh-Ctrl-Fkeys” should be chosen in the KEYS (F5) Setup menu. If an
ANSI keyboard is attached, the “F1 to F5
keys = Local” should be chosen in the KEYS (F5) Setup menu.
To reposition any window on your screen, hold down the Shift key while pressing a
cursor control (arrow) key.
Exit Keys trokes
To exit any window and restore the original screen:
Press ESC on the PC-style keyboards
Press F11 on the ANSI keyboard
Inhibiting Acces s
Access to desk accessories can be inhibited by selecting “Disabled” for “Desk
Acc” in the Setup menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
Calendar
63
Calendar
This displays a calendar for any month from the years 1900 to 2099. The current date
is displayed at the bottom. The keys below control the calendar that is displayed:
§
§
§
Right- and left-arrow keys – Display an earlier or later month.
Up- a nd down-arrow keys – Display the selected month in an earlier or later year.
Esc – Exit calendar.
The specified calendar month will display as shown below:
Clock
The clock menu (shown below) contains seven lines which can be modified:
Date
Jan. 1, 1995
Time
08:00:00 AM
Display
Type
Off
12
Column
Alarm Set
Tone
48
12:00 PM
Off
Use the following keys to make changes:
§
§
Up- or down-arrow keys – Select a line. The line is highlighted.
Left- or right-arrow keys – Select a field on the chosen line. The selected field is
now highlighted.
§
§
§
§
Spacebar – Move “up” through options available for this field.
Shift-Spacebar – Move “down” the options.
Enter (num ) – Revert to the default setting for the current field.
Esc – Exit clock and save settings.
Each of the seven fields is described below:
Download from Www.Somanuals.com. All Manuals Search And Download.
Calculator
64
Da te – Use the left or right arrow keys to highlight each field of the date (month, day,
and year). Then use the Spacebar or Shift-Spacebar to cycle through the settings. The
date can also be set by the host.
Time – Use the procedure described for Date above to set the hour, minutes, or seconds.
The clock is reset to 08:00 AM at power-up. Due to hardware limitaions, the clock
may drift by 15 seconds per day. We recommend setting the termina’s time as part
of the system
login process.
Dis p la y – Indicate whether only Time, only Date, or both the Time and the Date are
displayed on the top status line. Display of Time/ Date can also be turned Off. The
date display can also be set by the host.
Type – Select whether the clock functions on a 12-hour or 24-hour basis.
Column – Set the column (36-99) in which the date/ time will display (as enabled by
Display above).
Alarm Set – Time at which an alarm (a 1-2 second bell tone) should sound.
Tone – How alarm tone(s) should be activated: every Hour, on the Alarm setting only,
or both on the Alarm setting and Hourly. The alarm tone can also be turned Off.
Calculator
The numeric keypad located on the right side of your keyboard will serve as your
calculator. See the figures below to relate the display to the keys on the numeric
keypad that control it.
Note that the ANSI keyboard calculator display is identical to the ones shown below
for the PC+ keyboard except that the controlling keys on the numeric keypad are
different (the ANSI keyboard control keys include PF1-PF4 keys and function keys
F16-F20).
The calculator can process up to 10 digits to the left of the decimal point, and up to 9
to the right. When a number or number operator is pressed, it is momentarily
highlighted on the display.
Number operators are defined as follows:
§
+, -, / , X– The respective operations of addition, subtraction, division, and
multiplication.
§
§
§
§
§
MS – stores the displayed value in memory.
MR – displays the stored value
M + – adds the displayed value to memory.
+/ - – make a number positive/ negative.
C/ A – Displays 0.0 when pressed once. When pressed twice, clears memory.
The figures below represents the calculator display:
Download from Www.Somanuals.com. All Manuals Search And Download.
Calculator Dis play (EP C ke yboard)
Calculator Dis play (P C+ ke yboard)
In addition to the keys on the numeric keypad, you may use:
§
§
T – Toggle “tape” on/ off. Results scroll above the display.
P – Toggle “printer” on/ off. Results are transmitted onto the printer.
Use the printer option only when a printer is connected. Press Ctrl-Shft-Tab to
clear a printer error.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
66
Desk Accessories
§
§
X – Exit the calculator, transmitting the final result to the current application.
(Shift-X transmits the result with no leading or trailing spaces).
Ctrl-(a num ber on the num eric keypad) – Specify the precision, where the
number of decimal places that will be displayed is equal to the number pressed
with the Ctrl key.
§
Esc – Exit calculator.
ASCII Chart
The ASCII chart, upon entry to this desk accessory, is centered on the character on
which your cursor was last placed, and that character is highlighted. The chart will
display as shown below:
Characters are also displayed in octal, hexadecimal, and binary number
representations. The CHAR column contains the ASCII representation of the
character.
Use the following keys to change the display of the ASCII chart:
§
§
§
Up- or down-arrow – Scroll up or down the characters in the ASCII chart (0-
127).
Left- or right-arrow – Scroll through the available font banks. The characters will
display from the selected font bank.
Ctrl-• ,Ctrl-® , Ctrl-¯, Ctrl-¬ – Move the cursor on the screen up, right, down,
or left. The ASCII chart will be redisplayed, and the chart will be centered on the
character that the cursor now rests upon.
Upon exit, the cursor will be restored to its previous location at the tme of entry to
the desk accessory(ies).
§
Esc – Exit the ASCII chart.
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostic Menu
67
Diagnostic Menu
This desk accessory is used to display terminal configuration information such as the
amount of memory (RAM) in the terminal, the style of keyboard that you are using,
and the firmware revision level. An example of the diagnostic menu is shown below:
265
Screen RAM
Character
Attribute
32K
32K
8K
P0000
P0000
P0000
P0000
P0000
P0000
P0000
000000
P0000
P0000
P0000
P0000
000000
CGEN RAM
Scratch RAM
NVRAM
32K
Code ROM 3C10
Keyboard Type
256K
PC+
Video Tim ing
EIA port
RS-232
RS-232
AUX port
PARALLEL port
598-XXXXXXX
If you require technical support, this menu provides a means for our support team to
quickly assess your terminal installed options.
Download from Www.Somanuals.com. All Manuals Search And Download.
A
Appendix
Local Keys
Scan Code
Mode
Action
PC Keboard
ANSI Keboard
Toggle Caps-Lock
Toggle Num-Lock
Toggle Scroll-Lock1
Toggle Auto Print2
Toggle Block-Mode
Toggle Monitor Mode
No
Lock
Lock
No
Num-Lock
No
Scroll-Lock
F1
Yes
Yes
Yes
Ctrl-Print-Screen
Ctrl-Shift-Pause
Ctrl-Shift-1\End
Ctrl-F2*
F4*
Ctrl-Shift-1 (num)
Toggle Ins/Replace
Instant Screen Saver3
No
Yes
Ctrl-Insert
Ctrl-Shift-*
Ctrl-PF4
Ctrl-Shift-PF3
Soft Reset4
No
No
Shift-Scroll Lock
Ctrl-Shift-Scroll
Lock
Shift-F3*
Ctrl- F3*
Hard Reset (Power On)
Break5
Yes
No
Ctrl-Pause
Pause
F5*
Modem-Disconnect6
Send-Answerback
Print-Page
Shift-F5*
Ctrl- F5*
No
Shift-Pause
Ctrl-Shift-Del\.
Yes
Ctrl-Shift-.(num)
Continued
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Loca l Keys
70
Continued
Scan Code
Mode
Action
PC Keboard
ANSI Keboard
Increment Scroll Rate7
Decrement Scroll Rate7
Raise Split8
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Ctrl-Shift-•
Ctrl-Shift-¯
Ctrl- – (num)
Ctrl- , (num)
Ctrl-Shift- – (num)
Ctrl-•
Ctrl-Shift-•
Ctrl-Shift-¯
Ctrl- – (num)
Ctrl- , (num)
Ctrl-Shift- – (num)
Ctrl-•
Lower Split8
Split-Full Toggle8
Roll-Window-Up8
Roll-Window-Down8
Change Status Line9
Home & Clear Page
Auto Adjust Window
Ctrl-¯
Ctrl-¯
Ctrl-®
Ctrl-®
Ctrl-Shift-Home
Ctrl-Home
Toggle Session
Yes
Yes
Ctrl-Enter (num)
Ctrl-Enter (num)
Enter Desk Accessory
Mode
Ctrl-¬
Ctrl-¬
Enter Setup Mode10
Exit Setup Mode10
Enter Clock11
Enter Calendar11
Enter Calculator11
Enter ASCII Chart11
Enter Diagnostics11
Exit Any Desk Accessory
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Ctrl-Scroll Lock
Pause
F3*
F14
Ctrl-Shift-F1
Ctrl-Shift-F2
Ctrl-Shift-F3
Ctrl-Shift-F4
Ctrl-Shift-F5
Esc
Ctrl-Shift-F1*
Ctrl-Shift-F2*
Ctrl-Shift-F3*
Ctrl-Shift-F4*
Ctrl-Shift-F5*
F11 (Esc)
Next Page12
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Ctrl-Page Down
Ctrl-Page Up
Ctrl-0\Ins
Ctrl-Next Screen
Ctrl-Prev Screen
Ctrl-0 (num)
Ctrl-1 (num)
Ctrl-2 (num)
Ctrl-3 (num)
Ctrl-4 (num)
Ctrl-5 (num)
Ctrl-6 (num)
Ctrl-7 (num)
Ctrl-8 (num)
Ctrl-9 (num)
Ctrl-Tab
Previous Page12
Display Page 013
Display Page 113
Display Page 213
Display Page 313
Display Page 413
Display Page 513
Display Page 613
Display Page 713
Display Page 813
Display Page 913
Program Banner
Local Block Copy
Line Copy
Ctrl-1\End
Ctrl-2\¯
Ctrl-3\Page Down
Ctrl-4\¬
Ctrl-5
Ctrl-6\®
Ctrl-7\Home
Ctrl-8\•
Ctrl-9\Page Up
Ctrl-Tab
Alt-Home
Alt-Delete
Alt-Insert
Alt-Select**
Alt-Find**
Alt-Insert Here**
Paste from Buffer
Download from Www.Somanuals.com. All Manuals Search And Download.
Loca l Keys
71
In Scan Code Mode, this chart applies only when Local Leadin
is on.
Download from Www.Somanuals.com. All Manuals Search And Download.
Loca l Keys
72
NOTES:
1
2
3
4
This function is operational only if EIA (Aux) Rcv-Prtcl = Xon-Xoff/ XPC or DTR.
In ANSI emulations, this keystroke toggles in and out of Auto Print Mode.
This function is operational even if Screen Saver is set to off.
This function unlocks the keyboard, turns off all print modes and re-initializes the serial ports
for setup parameters.
5
6
7
The length of the Break Signal is dependent on the setup parameter of “EIA (Aux) Break.”
This keystroke is dependent on the “Disconnect” setting in the “Keys” (F5) setup menu.
The Increment Scroll Rate toggles the scroll rate to the fastest smooth scroll. This function
also stops at the jump scroll. The Decrement Scroll Rate toggles from jump scroll to the
fastest smooth scroll toward the slowest smooth scroll.
8
9
These functions are not available in ANSI emulations.
The Change Status Line function will toggle in the status line display from “Indicator” to
“Host Write” to “Both” to “Off” in ANSI Emulations and “Standard” to “Extended” to “Off”
on ASCII Emulations.
10
11
For other keystrokes for these functions, see the Setup chapter.
Keystrokes for these functions are only operational if the “Desk Acc= Sh-Ctrl-Fkeys” in the
setup menu.
12
13
When a Split Screen is not enabled, these keys select the next or previous pages. Wrapping
takes place from the last page to the first and vice versa.
These local functions are operational only if the selected page is available.
Download from Www.Somanuals.com. All Manuals Search And Download.
P a ge Configurations—Single and Dual Session
73
Page Configurations —Single and Dual Session
Num ber of Pages
80/ 132
Single ession
80-only
Dual ession
80-only
Lines per Page
80/ 132
24
48
96
192
*24
8
4
2
1
10
5
2
4
2
1
-
4
2
1
-
1
2 (24/176)
2 (24/216)
2 (24/76)
2 (24/96)
25
8
9
4
4
50
4
4
2
2
100
200
*25
2
1
2
1
1
-
1
-
2 (25/175)
2 (25/215)
2 (25/75)
2 (25/95)
42
5
5
2
2
84
2
2
1
1
168
*42
1
1
-
-
2 (42/158)
2 (42/198)
2 (42/58)
2 (42/78)
43
5
5
2
2
86
2
2
1
1
172
*43
1
1
-
-
2 (43/157)
2 (43/197)
2 (43/57)
2 (43/77)
When a page length (in the first column) is preceded by an asterisk (*a total of two
pages will be available. The first page contains the selected number olines and the
second page contains the remaining allowable lines in memory. The number of
lines are listed on this chart as (first page/ second page).
Download from Www.Somanuals.com. All Manuals Search And Download.
chapter
1
User’s Notes
75
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE TO INSTALLER
This equipment complies with the FCC Regulation for Class A devices, Subpart J of Part 15.
Shielded, grounded interface cables were used on all ports for FCC radiated emission testing.
The manufacturer is not responsible for any violation of the FCC Regulation for Class A
devices that is caused by unauthorized modification of the equipment, or caused by
equipment installation not in accordance with the instructions in this manual.
This equipment generates, uses, and can radiate radio frequency energy and may cause radio or
television interference. All user equipment that interfaces with other products should be
connected with shielded cables. (Contact a local dealer for more information on shielded cable
assemblies and their availability.)
There is no guarantee that interference will not occur. If radio or television interference occurs
(this can be determined by turning the equipment off and on while the radio or television is
on), the user is solely responsible for correcting the interference and is encouraged to take one
or more of these measures:
1.
2.
3.
Reorient the receiving antenna.
Relocate the equipment, or move the equipment away from the receiver.
Plug the equipment into a different outlet so the unit and receiver are on different branch
circuits.
4.
Consult the dealer or an experienced radio/ television technician.
It is also suggested that the user read the FCC booklet entitled How to Identify and Resolve
Radio-TV Interference Problems. The booklet is available from the US Government Printing
Office, Washington, DC 20402. (When ordering the booklet, specify stock number 04-000-
00345-4.)
Site Preparation
The screen display geometry on terminal products is aligned using magnetic devices. External
magnetic fields created by other types of electronic equipment, such as printers, in very close
proximity to the terminal, may cause minor display distortion.
Examples of display distortion include:
þ
þ
þ
Shaky video
Wavy lines
Tilted display
This magnetic field interaction only occurs over a very short distance, normally less than
twelve inches, and can be corrected by separating the equipment and/ or slightly reorienting
the display.
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Support
Questions about this product should be directed to the Technical Support Department
of the distributor from which you obtained your Boundless Technologies equipment.
When requesting assistance, please have all pertinent information available including
any error messages that may have appeared either on the terminal or the host.
If your distributor fails to provide adequate support for your needs, please contact the
Boundless Technologies Technical Support Department directly. You will be required
to provide the name of your distributor, and a description of the problem as described
above.
Please refer to the Boundless Technologies Guide to Support Services which was
packaged with the terminal.
Boundless Technologies can be reached at:
Boundless Technologies, Inc.
Technical Support Department
100 Marcus Blvd.
Hauppauge, NY 11788
(800) 231-5445 ext. 7259 (voice)
(516) 342-7378 (fax)
Email:
BBS:
407-333-8326 1200/ 14400 baud
8 data bits, 1 stop bit, no parity
ftp.boundless.com
ftp:
Web site:
Download from Www.Somanuals.com. All Manuals Search And Download.
|