User’s Manual
BV7320
IN-DASH DVD/MP3/CD AM/FM
RECEIVER WITH 3.2" (81mm)
WIDESCREEN TFT MONITOR
WITH DUAL (FRONT AND REAR)
USB PORTS, SD MEMORY CARD PORT
AND FRONT PANEL AV INPUT
BV7320
IN-DASH DVD/MP3/CD
AM/FM RECEIVER WITH 3.2" (81mm)
WIDESCREEN TFT MONITOR
WITH DUAL (FRONT AND REAR) USB PORTS
AND FRONT PANEL AV INPUT
11.2011
BOSS Audio Systems
3451 Lunar Court • Oxnard, CA 93030
iPod® is a trademark of Apple, Inc.
registered in the U.S. and other countries.
Boss Audio Systems is not affiliated with Apple, Inc.
7. Specifications
PRECAUTION
General Specification
WARNING: TO REDUCE THE
RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION
Power Supply Requirement..................................................DC 12V
Maximum Power Output...................4 x 80W(measured at DC 14.4 V)
Dimensions(w x h x d)............................................7”W x 2”H x 6.5”D
RISK OF ELECTRIC SHOCK
DO NOT OPEN
!
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
DVD Deck Specification
Format....................................DVD/VCD/JPEG/MP4 (AVI,ASF ,WMV,
MPEG-1,MPEG-2,MPEG-4)/MP3/WMA/CD
Video System....................NTSC/PAL/PAL-M/PAL-N/AUTO(optional)
Audio System..............................................................24 bit/96KHz
Loading System.......................................................... Auto Loading
Mounting Angle.................................................................0 to +/-30
The lightening flash with arrowhead symbol, within an equilateral triangle, is
intended the alert the user to the presence of uninsulated dangerous voltage
within the products enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert user to
the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
!
Video Specification
Video Type...................................................................16:9 and 4:3
Video Output level......................................Composite:1.0± 0.2Vp-p
Load impedance: 75 ohms
CLASS 1 LASER PRODUCT
Horizontal Resolution................................................................500
Audio Specification
Laser product symbol: located on the rear panel of the unit, indicate this player is a class
laser product, only use weak laser and no hazardous radiation outside of the unit.
Audio Output(Analog audio)..........................................2.0+0-1.0 Vrms
Frequency Response.............................20Hz ~ 20KHz(at 1KHz 0 dB)
S/N Ratio(Audio).............................................≥90dB(at 1KHz 0 dB)
Separation..............................................................................50dB
1.Read through this instruction manual before installation and use.
2.Before removing the unit, remove the disc from the unit first.
3.Do not open the cover or touch any of the components exposed out of the unit, only for
qualified technicians.
Radio Specification
4.Do not expose the unit to direct sunlight or nearby objects that radiate heat to avoid
damage the unit.
FM Section
Frequency range..............................................87.5MHz - 107.9MHz
Usable sensitivity......................................................................3uV
I.F Frequency....................................................................10.7MHz
5.Do not place the unit in moist and humid conditions.
6.Please ensure the ventilation holes are not covered to avoid overheating and malfunction.
AM Section
7.Clear the panel and case with soft dry cloth only, do not apply any kind of thinner,
alcohol or sprays.
Frequency..........................................................530KHz - 1710KHz
6. Trouble Shooting
Contents
Please read the user manual carefully before using the DVD player. If you have any trouble
using this player, try to solve the problems by the suggestions mentioned below. If you can
not remove the trouble after using all the suggestions, please contact the company or the
technical service center authorized by us. For the sake of your safety, please do not open the
cover and repair the player by yourself, if that, it may cause electric shock.
1. Before Operation...........................................................................................3
1.1 Glossary................................................................................................ 3
1.2 Precautions............................................................................................3
1.3 Maintenance and Cleaning of Discs..........................................................4
1.4 Battery Information of the Remote Control.................................................4
1.5 The Remote Control Description...............................................................5
1.6 Locations and Names of the Controls........................................................6
1.7 Description of the Rear Cabinet....................... ........................................7
1.8 Unit Installation......................................................................................8
NO PICTURE, SOUND AND INDICATION
*
*
*
Ensure that the power switch is on.
Ensure that the power cord is not damaged or the fuse is not blown.
Ensure that the power plug is connected to the inlet tightly.
NO SOUND BUT HAVE PICTURE
*
*
*
*
*
Ensure that the player’s audio output has a good connection with amplifier.
Check whether the audio connector is damaged.
Check whether you have turned down the volume.
Ensure that you have set the right AUDIO setup of the player.
Ensure that the audio is not muted.
2. Common Operation........................................................................................9
3. Radio Operation...........................................................................................11
4. Basic Disc, USB or MMC/SD Operation..........................................................12
4.1 Begin Playback......................................................................................12
4.2 Pause Playback.....................................................................................13
4.3 Stop Playback .......................................................................................13
4.4 Select Chapter/Track with the UP/DN or the >>|/|<< Buttons......................13
4.5 Select Chapter/Track with the Number Buttons.........................................13
4.6 Select Chapter/Track with the Root/PBC Menu.........................................13
4.7 Terminate the Playback..........................................................................14
NO PICTURE BUT HAVE SOUND
*
*
*
*
Ensure that the player s video output has a good connection with monitor’s video input.
Ensure that you have turned your TV to the AV input channel connecting to your player.
Check whether the video connector is damaged.
Ensure that you have set the right VIDEO settings of the player.
BLACK AND WHITE PICTURE OR SCREEN ROLLING
Ensure that you have set the right TV SYSTEM (e.g. PAL, NTSC) setting.
*
FLAWS OF PICTURE OR SOUND
5. Advanced Disc, USB or MMC/SD Operation....................................................14
5.1 Playback with Speed..............................................................................14
5.2 Playback with Slow Speed......................................................................14
5.3 Playback with Still Frame........................................................................15
5.4 Playback Repeatedly..............................................................................15
5.4.1 One/All Repeat...................................................................................15
5.4.2 A-B Repeat.........................................................................................15
5.5 Playback in Scan Mode...........................................................................16
5.6 Playback from a specified Chapter/Track or a Specified Time.....................16
5.7 Playback in Random...............................................................................16
5.8 Playback in Different Angle.....................................................................16
5.9 Playback in Zoom Mode..........................................................................16
5.10 Change the Caption Language..............................................................17
5.11 Change the Audio Language..................................................................17
5.12 Change the Video Signal System...........................................................17
5.13 Look over the Playback Status...............................................................17
5.14 Program Playback................................................................................18
5.15 Playback the Picture CD in JPEG Format................................................18
5.16 Mp4 OPERATION.................................................................................19
5.17 ESP and ID3 Function...........................................................................19
5.18 USB and MMC/SD Reader Operation.....................................................19
5.19 The DVD System Menu Setup Operation................................................19
5.20 Parental Control..................................................................................23
5.21 Region Code.......................................................................................24
*
*
*
*
Check whether the setting of AUDIO is right.
Check whether the disc is scratched or stained.
Check whether the AV connector and the output terminal is stained.
Check whether there is condensation inside the Lens. If so, leave the player off for an hour
or so, then try again.
*
Check whether the installation angle is less than 30.
DISPLAY NO DISC OR BAD DISC
*
*
*
*
*
*
Ensure that you have put the disc in the unit.
Check whether the disc is put in the reverse side.
Check whether the disc is distorted.
Check whether the disc is stained or scratched badly.
Ensure that the disc format is compatible to the player.
Ensure that the temperature inside the car is not too high. If so, cool off until the ambient
temperature returns to normal.
*
Replace another disc to insert it into the disc compartment.
REMOTE CONTROL IS INSENSITIVE OR DOES NOT WORK
*
Check the batteries of remote control and make sure that they are powerful and have
good conductivity.
*
*
Direct the remote control to the IR sensor of the player.
Check whether there are some obstacles between the remote control and IR sensor.
SOME FUNCTION BUTTONS DO NOT WORK
*
*
*
Turn off the power, then turn on again.
Reset the unit to zero, then turn on again.
Remove the front panel from the unit, then install it again and then turn on again.
6. Trouble Shooting.........................................................................................25
7. Specifications.............................................................................................26
THE RADIO DOES NOT WORK
Check whether the antenna cable is connected firmly. Or manually tune for a station.
*
1. Before Operation
1.1 Glossary
PBC (playback control)
It is a kind of signal(menu) recorded in the disc with SVCD or VCD2.0
format used for the playback control. For the discs containing PBC, It can
playback interactive software with the menu displayed on monitor. And if the
disc contain still images, it can playback high definition of still images.
5.21 The Region Code
Q: Why does the unit display REGION ERROR after inserting disc into
disc compartment ?
Title
Generally, the title is the important part of DVD disc. for example, the
theme part of movie is title 1, the part described how to make movie is title
2, the cast is title 3, etc. Every title contain a serial number that is easy to
lookup.
A: Because the DVD player and disc has respective region code. If the
region codes of them do not match with each other, the DVD player
can not play the disc.
Chapter
A title can be divided into several blocks, so that every block can be operated
as a unit, the unit is called chapter. The chapter contain a unit at least.
Appendix: The region code of DVD:
Track
It is the biggest component of VCD. Generally, every song of karaoke disc
is a track.
The Motion Picture Association of America (MPAA) divided the world
into 6 regions, and gave every region a code, namely region code. The
region codes and the countries or areas represented by the region codes
are as follows:
PROTECTIVE CASE
1.2 Precautions
Safety
Region 1: America, Canada, East-Pacific Inlands;
FRONT PANEL
Region 2: Japan, West Europe, North Europe, Egypt, South Africa, Middle
East;
1. Power Source: The unit should be connected to power supply only of
the type described in the operating instructions or as marked on the unit.
2. The unit is designed for negative terminal of the battery which is
connected to the vehicle metal. Please confirm it before installation.
3. Do not allow the speaker wires to be shorted together when the unit is
switched on. Otherwise it may overload or burn out the power amplifier.
4. Do not install the detachable panel before connecting the wire.
5. The protective case is to safely keep the front panel(see the photo).
Region 3: South-east Asian countries include Taiwan, Hong Kong, South
Korea, Thailand, indonesia, etc.;
Region 4: Australia, New Zealand, Central South America, South Pacific
Inlands;
Region 5: Russia, Mongolia, Indian Peninsula, Middle Asia, East Europe,
North Korea, North Africa, North-west Asia etc.;
Environment
1. Do not use this unit when water and moisture is near it.
2. If moisture forms inside the Lens, it may not operate properly. To correct
this problem, wait about one hour for the moisture to evaporate.
3. If the car interior is extremely hot, do not use the player until the car has
been driven for a while to cool off the interior.
Region 6: China mainland.
1.3 Maintenance and Cleaning of Discs
Disc Maintenance
5.20 Parental Control
1. To keep the disc clean, handle the disc by its edge, do not touch the disc
surface of the play side.
2. Do not stick paper or tape on the disc. If there is anything on the disc surface,
wipe it up with a soft cloth before using.
3. Do not expose the disc to direct sunlight, or nearby heat sources such as
caliduct, or leave it in a car parked in direct sunlight where there can be a
considerable rise in temperature.
Q: Why after inserting DVD disc in the disc slot, a dialogue window appears that
asks to input a 4 digits password?
A:This is because the movie you are playing was rated with the Parental Control,
and the current rating level of DVD player is lower than the current disc. You
must input right password and enter it to entry Parental Control setup menu and
then set a equal or higher rating level than one of current disc. So that you can
playback the disc.You must change the Parental Control setting to higher rating
level.
4. Put the disc inside disc case to keep temperature after finishing playback.
Disc Cleaning
1. Before playing, wipe the disc with a clean cloth. wipe the disc outwards from
the disc center.
!
NOTE
2. Do not use petrol, thinner, commercial cleaner or anti-static spray used for
plastic LP to wipe disc.
*
If you have not changed the password, the factory preset password for the DVD
player is 0000. To change the password you should input the current password
and then input the new password 2 times.
+
side up
B
A
Parental Control
Fig.1
Fig.2
Fig.3
The Parental Control function of a DVD player can control the playback of movie
rated level in a disc. You can set the DVD player to be a certain rating level with
SETUP MENU on screen. If the rating level in the disc is higher than one set in the
DVD player, the DVD player can not playback the disc. The rating level setup can
be protected by the password. Therein, if you select Unlock , the Parental Control
function will be invalid, and all level DVD rating will be played.
1.4 Battery Information of the Remote Control
Replace Battery in the Remote Control:
1.Before using the remote control for the first time, pull the insulating
sheet out of the remote control as the direction indicated by the
arrow.(see fig.1)
2.Press the movable block hold as the direction indicated by the A arrow
(See fig.2), then pull the battery holder out of the remote control as
the direction indicated by the B arrow(see fig.2).
3.Replace the old battery by a new battery with (+) polarity side upward.
(See fig.3).
The disc movie can be designed as that the DVD player will playback the different
version of content of a same movie according to the different rating level set by
Parental Control. Depending on the DVD feature of seamless switching described
above, the scenes that are not fitting for children will be cleared or replaced by the
other fitting scene automatically.
All rating levels of Parental Control are as follows:
4.Insert the battery holder to the original position in remote control.
(See fig.3).
Note about the Battery of the Remote Control:
1.Improper use of battery may cause overheating or explosion, and could
result in injury or fire .
2.Battery leakage may cause damage to the remote control(Battery
Life: 6 months with normal use in normal room temperature).
3.Do not short the battery.
Unlock
Kid Safe
G
1
2
3
4
5
6
7
8
PG
PG 13
PG R
R
NC 17
Adult
4.Do not throw the battery into fire.
5.To avoid the risk of accident, keep the battery out of reach of children.
HUE
1.5 The Remote Control Description
It is for adjusting the hue of the video output.
3
27
1
35
1. P/N BUTTON
2. MENU BUTTON
3. POWER BUTTON
4. ^ BUTTON
SATURATION
It is for adjusting the saturation of the video output.
4
14
SHARPNESS
It is for adjusting the sharpness of the video output.
2
33
6
29
32
9
5.19.5 SPEAKER SETUP
5. >>| BUTTON
8
5
34
13
31
30
SPEAKER SETUP
DOWNMIX
6. > BUTTON
7
7. |<< BUTTON
8. v BUTTON
10
DOWNMIX
11
It is for selecting your desired sound effect when there is not central speaker
and sub-woofer. There are 3 mode: LT/RT, STEREO, VSS.
9. SEL BUTTON
10. PLAY/PAUSE BUTTON
12
16
15
18
24
28
LT/RT: When playing a disc with PRO LOGIC Dolby stereo effect, choose the
item, so it will output audio signal with vivid theatre effect.
11. NUMBER(0~10,+10
-10) BUTTONS
12. 10+ BUTTON
21
22
STEREO: If you choose the item, when outputting audio signal with 5.1 channels,
it will output the left and right channels of signal ; when outputting audio signal
with 2 channels, it will output the common 2 channels of stereo signal.
17
26
25
23
36
37
19
20
39
13. SETUP BUTTON
14. MODE BUTTON
VSS: If you choose the item, when playing a disc recorded with 5.1 channels,
the main channel speakers can output audio signal with VSS effect.
38
15. APS BUTTON
5.l9.6 DIGITAL SETUP
28. LOC/SLOW-FWD BUTTON
16. SEARCH BUTTON
17. RDM BUTTON
18. RPT BUTTON
DIGITAL SETUP
29. MUTE BUTTON
30. STOP BUTTON
31. VOLUME- BUTTON
32. < BUTTON
OP MODE
DYNAMIC RANGE
DUAL MONO
19. SUBTITLE BUTTON
20. TITLE/PBC BUTTON
21. ANGLE/ST BUTTON
22. ZOOM BUTTON
23. AUDIO BUTTON
24. CLK BUTTON
OP MODE
It is for selecting audio output mode
LINE OUT: It can linearly compress the audio signal. So the volume level is lower.
RF REMOD: It can make the volume level higher.
33. OK BUTTON
34. VOLUME+ BUTTON
35. BAND BUTTON
36. PROG BUTTON
37. OSD BUTTON
38. LOUD BUTTON
39. STEP BUTTON
DYNAMIC RANGE
After selecting the compression mode of LINE OUT, set the item, so you can
adjust the linear compression ratio. If you set it to be FULL, the Peak-to-Peak
value of the audio signal is the minimum; if you set it to be OFF, the Peak-to-
Peak value is the maximum.
25. A-B BUTTON
DUAL MONO
26. INT BUTTON
It is for selecting a desired audio output mode for the left and right ways of signal.
There are 4 modes in all as follows: STEREO, MONO L, MONO R, MIX MONO.
27. EQ BUTTON
1.6 Locations and Names of the Controls
5.19.2 LANGUAGE SETUP
6
8
9
16
11
1
10 14 15
3
20
7
LANGUAGE SETUP
OSD LANGUAGE
AUDIO LANG
SUBTITLE LANG
MENU LANG
3.2” TFT
OSD LANGUAGE
This item is for selecting the language of the SYSTEM MENU and all operating
prompt interface displayed during playback.
AUDIO LANG
This item is for selecting a audio language.
SUBTITLE LANG
This item is for selecting a subtitle language.
MENU LANG
5
12
18
19
4
17
22
The figure of the front panel
This item is for selecting a disc menu language.
5.l9.3 AUDIO SETUP
AUDIO SETUP
AUDIO OUT
KEY
AUDIO OUT
there is only ANALOG mode, i.e. SPDIF/OFF, not optional.
KEY
It is for selecting your desired basic music tone(from low to high).
24
2
21 23 13
The figure of the Unit Chassis Facet After removing the Front Panel
1. POWER/MUTE BUTTON
5.l9.4 VIDEO SETUP
13. EJECT BUTTON
2. DISC SLOT
14. 1/PLAY/PAUSE BUTTON
3. RELEASE BUTTON
15. 2/INT BUTTON
4. MODE
VIDEO SETUP
BRIGHTNESS
CONTRAST
HUE
SATURATION
SHARPNESS
16. 3/RPT BUTTON
5. CLOCK BUTTON
17. 4/RDM BUTTON
6. SEL BUTTON
18. 5/-10 BUTTON
AND VOL KNOB
19. 6/+10 BUTTON
7. EQ BUTTON
20. USB SOCKET
8. SMALL MONITOR
21. RESET BUTTON
9. IR REMOTE SENSOR
BRIGHTNESS
It is for adjusting the brightness of the video output.
CONTRAST
22. AV IN SOCKET
10. BAND BUTTON
23. LED INDICATOR
11. UP AND DN BUTTONS
24. SD/MMC CARD SLOT
12. APS BUTTON
It is for adjusting the contrast of the video output.
20
7
1.7 Description of the Rear Cabinet
GREEN
GREY
For the DVD System Menu, there are 6 setup pages in all. They display as follows:
SUBWOOFER
RED
R
RED
R
GREY
GREY
BLACK
BLACK
5.19.1 SYSTEM SETUP
REAR RCA LINE OUT
FRONT RCA LINE OUT
Fixing Screw Bolt
WHITE
L
SYSTEM SETUP
WHITE
L
TV SYSTEM
TV TYPE
Reversal line White
Parking Line GREEN
PASSWORD
RATING
DEFAULT
YELLOW
YELLOW
BLACK
GRAY
GRAY
USB LINE IN
TV SYSTEM
Fixed ISO Female Connector
VIDEO OUT
This product supports output of various TV systems.
If your monitor has only NTSC or PAL system, the screen will blink and become
colorless when a wrong TV system is selected. In this case, press the N/P button
to switch the right TV system to match the TV color system.
TV TYPE
Note:1. Parking wire must be connected, and the parking brake must be engaged in order for the monitor to work
2. Use the clip end of the Ground wire provided by manufacturer to connect Mounting Screw, use the other
end of the Ground wire to connect the negative pole of the power source. Otherwise, the video on screen
may flaches.
The setup item is for matching screen size.
Connecting the parking brake line to the parking brake system built in the car
4:3 PS: Choose the item when connecting a TV set with 4:3 screen. When playing
the pictures with 16:9 size, the left and right parts of the video will be cut out,
and display in full screen.
Parking brake
4:3 LB: Choose the item when connecting a TV set with 4:3 screen. When playing
the pictures with 16:9 size, the top and bottom parts of the TV screen will be
turned into a black square respectively.
Parking brake wires(Green)
16:9: Choose the item when connecting a TV set with 16:9 wide screen.
PASSWORD
Parking brake switch
(inside the car)
To metallic body or chassis of the car
This setup item is for locking or unlocking the rating level of the Parental Control.
The defaulted state is locked. The defaulted password is 0000.
You can set a new password that you like: Select the PASSWORD item and then
press the > button to enter it, then input the original password 0000, and then
press the OK button to unlock it. Press the > button to enter it again, then input
a new password that you like and then press the OK button to make it effective.
Before the other persons see the Manual, you should get the password in mind
and cut out the part of PASSWORD in the Manual.
The Description of the Fixed ISO Female Connector
RATING
This item is for setting a new rating level of the Parental Control.
1. Select the PASSWORD item and then press the > button to enter it, then input
the password mentioned above, and then press the OK button to unlock the
setting of the rating level of the Parental Control.
2. Select the RATING item and then press the > button to enter it, then use the
direction buttons to select your desired rating level, then press the OK button
to confirm.
3. Select the PASSWORD item again and then press the > button to enter it, then
input the password, and then press the OK button to lock the new setting of
the rating level of the Parental Control.
CONNECTOR A
CONNECTOR B
1.
1. Rear Right Speaker (+)
2. Rear Right Speaker (-)
3. Front Right Speaker (+)
4. Front Right Speaker (-)
5. Front Left Speaker (+)
6. Front Left Speaker (-)
7. Rear Left Speaker (+)
8. Rear Left Speaker (-)
2.
3.
4. Memory +12V(yellow)
5. Auto Antenna(blue)
6.
7. 12V (To Ignition Key)(red)
8. GROUND(black)
DEFAULT
This item is for making all setup items change back to original status.
3. During JPEG playback, press one of the >/</^/v buttons to change the angle of
viewing picture that is displaying as follows:
1.8 UNIT INSTALLATION
>: 90 deg cw; <: 90deg ccw; ^:UP<-->DOWN; v: LEFT<-->RIGHT
During JPEG playback, press the PROG button to change the mode of refresh picture.
During JPEG playback, press the STOP button to stop playing and return to the root
menu.
*
*
During JPEG playback, the following buttons are not available: SLOW-FWD,
SUBTITLE, TITLE, ANGLE, STEP, AUDIO, RDM, INT and A-B.
In JPEG mode,the other operations are same as ones in MP3/WMA mode.
INSTALLATION INSTRUCTIONS
THE UNIT INSTALLATION IS ANTI-THEFT ONE. THE UNIT
CHASSIS WEARS A SLIDING METAL HOUSING. FIRSTLY
CONNECT THE POWER LINES, SPEAKER LINES AND
AUTO ANTENNAACCORDING TO MANUAL REQUIREMENT,
THEN INSTALL THE SLIDING METAL HOUSING IN A CAR
ACCORDING TO THE DIAGRAM.
5.16 MP4 Operation
TO BOOST UP THE CAPABILITY OF
ANTI-JAMMING, PLEASE FIX THE
METAL STRAP ON THE METAL
CONNECTED TO THE CHASSIS OF
THE CAR.
1. The root menu will display on the monitor when it begins to switch to DISC mode,
METAL STRAP
then it will automatically play the first file.
SELECT THE PROPER TABS
OF THE SLIDING METAL
HOUSING TO FIX THE
During playback, press the STOP button to stop playing and return to the root menu.
2. When displaying the root menu, press the direction buttons to select your desired
FOLDER or file, then press the OK or PLAY button to open the FOLDER, or play the
selected file.
SLIDING METAL HOUSING.
When displaying the root menu, you can also use the number buttons to select the
serial number of the file and play the file.
UNIT CHASSIS
*
*
The ANGLE, PROG, RDM, INT and TITLE/PBC button are not valid in this mode.
The other functions are same as ones in DVD disc; but the RPT function is same as
one in MP3/WMA.
DASH BOARD
SLIDING METAL HOUSING
PLASTIC TRIM OUT
FRONT PANEL
5.17 ESP and ID3 Function
TO DRAW THE CHASSIS OUT OF THE
SLIDING METAL HOUSING, INSERT
THE LEFT AND RIGHT KEY PLATES
INTO THE TWO SIDES OF CHASSIS.
There is ESP function for all formats of discs.
In MP3/WMA mode, during playback, the information of the file name, folder name,
songs title, artist and album will be scrolling on the LCD display. As long as the
current playing MP3 music contains relevant ID3 tag information in version 1.0/2.0
format, the 3 items underlined above will be scrolling on the LCD display; otherwise,
they will not.
5.18 USB and MMC/SD Reader Operation
NOTE
Power on the DVD player, then insert the USB storage or MMC/SD Card(first flip down
the front panel), and then the monitor will display the root menu of the USB storage or
MMC/SD Card.
REMOVE THE DECK TRANSPORT
SCREWS BEFORE INSTALLING IT.
All the operations are same as ones of the corresponding format.
When you want to pull out the card, first push it, and then pull it out.
REMOVE THE SLIDING METAL HOUSING
EJECT BUTTON
RESET BUTTON
5.19 The DVD System Menu Setup Operation
1. Press the SETUP button on the remote control to access the DVD System Menu on
the monitor.
2. There are 6 setup pages in all for the System Menu. Press the > or < button to select
a desired setup page.
3. Press the ^ or v button to select an setup item in the selected setup page.
4. Press the > button to enter the setup item. Then press the v or ^ button to select a
desired mode of the setup item, finally press the OK button to confirm it.
*
*
Press the < button to return to the upper level.
Press the SETUP button again or use the direction buttons to highlight the item of the
EXIT SETUP and then press the OK button to exit the System Menu.
5.14 Program Playback
2. Common Operation
It allows you to enter the order in which you want some chapters/tracks in
DVD/VCD/MP3/WMA/CD disc to play.
1 During playback, press the PROG button to enter a program interface as
follows:
1. To turn on/off the unit
Under power off mode, press the POWER button to turn on the unit.
for DVD discs
for VCD/MP3/WMA/CD discs
P RO G R AM
Under power on mode, long press the POWER button on the front panel or
briefly press the POWER button on the remote control to turn off the unit.
P R O G R A M
T
C
T
C
T
C
T
C
1 _ _ _ _ 5 _ _ _ _ 9 __ _ _ 1 3 _ __ _
2 _ _ _ _ 6 _ _ _ _ 1 0 _ _ _ _ 1 4 __ _ _
1 _ _: _ _ 5 _ _ : _ _ 9 _ _ : _ _ 1 3 _ _ : __
2 _ _: _ _ 6 _ _ : _ _ 1 0 _ _ : _ _ 1 4 _ _ : _ _
3 _ _: _ _ 7 _ _ : _ _ 11 _ _ : _ _ 1 5 __ : _ _
4 _ _: _ _ 8 _ _ : _ _ 1 2 _ _ : _ _ 1 6 _ _ : _ _
3 _ _ _ _ 7 _ _ _ _ 11_ _ _ _ 15 _ _ __
4 _ _ _ _ 8 _ _ _ _ 1 2 _ _ _ _ 1 6 __ _ _
2. To select function mode and switch on/off TFT screen
Press the MODE button to select TUNER, DISC(After inserting a disc), USB
(After inserting a USB storage), Card(After inserting a MMC or SD card) or
AUX mode.
P l a y
C l e a r
P l a y
C l e a r
2 Use the direction buttons to move cursor onto the desired place for inputting
the sequence number.
3 Use the number button to input desired sequence number of title/chapter/
track with desired sequence.
4 Use the direction button to move cursor onto Play item, then press the OK
button to play the programmed titles/chapters/tracks in programmed order;
only pressing the PLAY button also can play the programmed titles/chapters
/tracks in programmed order.
Long press MODE button to switch off the TFT screen when driving on night
time. Then press one of any buttons to resume it.
Note: This unit has front and rear USB. Only one will work at a time.
3. To adjust sound level
Rotate the VOL knob on the front panel or press or hold the + or - button on
the remote control to directly adjust the volume level.
*
*
*
*
To exit program playback, first press the STOP button, then press the PLAY
button to enter sequence playback; or press the PROG button twice again.
To remove the all programmed sequence numbers, move the cursor onto
Clear item, then press the OK button.
To change the programmed sequence, move the cursor onto the item you
want to change, input the desired sequence number.
4. To mute sound
Press the MUTE button on the remote control to turn on/off MUTE mode.
Briefly pressing the POWER button on the front panel also can turn on/off
MUTE mode.
During VCD playback, if it is in PBC ON mode, at the same time of entering
the state of program playback, it turns off PBC mode.
In MUTE mode, the MUTE mode can be released by pressing the following
buttons: MUTE, VOL or +/-, SEL, MODE.
5.15 Playback the Picture CD in JPEG Format
5. To display and adjust the clock time
1. The root menu is displayed on the monitor when beginning to switch on DISC
mode. At the time, it plays MP3/WMA file.(the TITLE or MENU button is not
available).
Press the CLK button to display clock time on the small monitor of the front
panel.
In the root menu, the left file sort icon is for MP3/WMA file; the middle file sort
icon is for JPEG file; the right file sort icon is for VIDEO file. If one of these 3
file sort does not exist, you cannot move cursor onto the file sort icon.
2. When displaying the root menu, press the direction buttons to select your
desired FOLDER, file or file sort icon, then press the OK or PLAY button to
open the FOLDER, or play the selected file, or play only this sort of file.
When displaying the root menu, you can also use the number buttons to
select the serial number of the file and play the file.
Then long press the CLK button to change the color of the hour of the clock,
then rotate the VOL knob on the front panel or press the + or - button on the
remote control to adjust the hour; and then briefly press the SEL button to
change the color of the minute of the clock, then rotate the VOL knob on the
front panel or press the + or - button on the remote control to adjust the
minute.
6. To select a preset EQ mode
When you select a JPEG file sort icon, press the ^ or > button to select the
first JPEG file, then press the v button to select the desired JPEG file, finally
press the OK or PLAY/PAUSE button to display the JPEG picture in full screen
from the selected JPEG picture.
Press the EQ button to select the preset music equalizer curves: POP, ROCK,
CLAS, FLAT . The sound effect will be changed.
7. To remove the front panel
1) Press the RELEASE button on the front panel to flip down the front panel
from the unit;(see fig. 1)
ZOOMx2,ZOOMx3,ZOOMx4,ZOOMx1/2,ZOOMx1/3,ZOOMx1/4,ZOOM OFF.
Press one of the ^/v/>/< buttons to select the area you want to enlarge.
2) Flip down the front panel;(see fig. 2)
5.10 Change the Caption Language
3) Hold the right end of the front panel and pull out the right end as arrow direc-
tion, then pull out the whole front panel as arrow direction.(see fig. 3)
When playing a DVD disc, press the SUBTITLE button repeatedly to select
the language of the caption or turn off the caption.(depend on the current
disc)
When playing a VCD/MP3/WMA/CD disc , the button is not available.
REL
5.11 Change the Audio Language
Fig. 1
Fig. 2
Fig. 3
1. When playing a DVD disc , press the AUDIO button repeatedly on the remote
control to select the desired language type. (depend on the current disc)
2. When playing a VCD disc, press the AUDIO button repeatedly to select the
sound mode of the MONO L, MONO R, MIX MONO and Stereo, no language
function.
8. To mount the front panel
1) Insert left end of the front panel first as arrow direction, then push and hook
up the right end of the front panel onto the unit;(see fig. 4)
2) Flip the front panel upward till hearing a clip.(see fig. 5 and fig. 6)
3. When playing a CD/WMA/MP3 disc, the AUDIO button is disabled.
5.12 Change the Video Signal System
During playback of DVD/VCD disc, press the BAND(P/N) button on the front
panel or on the remote control repeatedly to change the VIDEO SIGNAL
SYSTEM mode.
Fig. 4
Fig. 5
Fig. 6
9. To turn on/off LOUD mode
Press the LOUD button on the remote control to turn on/off LOUD mode.
5.13 Look over the Playback Status
When turning on LOUD mode, it will enhance bass level immediately when
the bass is not enough.
1. When playing a DVD disc, press the OSD button repeatedly on the
remote control to turn on/off the playback status. When it is on, it will
display the information such as: the serial number of the playing title, the
serial number of the playing chapter, the elapsed time of the playing chapter,
the remained time of the playing chapter, the elapsed time of the playing title,
the remained time of the playing title, etc.
2. When playing a VCD/CD disc , press the OSD button repeatedly on the
remote control to turn on/off the playback status. When it is on, it will
display the information such as: the serial number of the playing track, the
elapsed time of the playing track, the remained time of the playing track, the
elapsted time of the disc, the remained time of the disc.
10. To reset the unit
When the display is distorted or the function buttons are not working correctly
or sound
is distorted, press the RELEASE button to detach the front panel from the
unit, then use a needle object to press the RESET button to reset
the unit to original setting.
11.To adjust the sound equalizer curves
3. When playing a MP3/WMA disc, press the OSD button repeatedly on
the remote control to turn on/off the playback status. When it is on, it will
display the information such as: the serial number of the playing track, the
elapsed time of the playing track, the remained time of the playing track.
To adjust the sound equalizer curves, briefly and repeatedly press the SEL
button to select the sound equalizer curves of VOL, BAS(without preset EQ),
TRE (without preset EQ), BAL, FAD, then rotate the VOL knob on the front
panel or press the + or - button to adjust level.
5.5 Playback in Scan Mode
3. Radio Operation
1. When playing a VCD(PBC OFF)/CD disc, press the INT button to play the
previous 15 seconds part of each track on the disc. Press the INT button
again to resume normal playback.
1. BAND BUTTON
In RADIO mode, press the BAND button on the remote control or on the front panel to
select your desired radio band of FM1, FM2, FM3, AM1 and Am2, then the selected BAND
will be displayed on the front panel monitor.
2. When playing a DVD/MP3/WMA disc, the INT button is not available.
5.6 Playback from a specified chapter/track or a specified time
2. TUNE/SEEK UP/DOWN BUTTONS
In RADIO mode:
1) Long press the UP/DN button on the front panel or the >>|/ |<< button on the remote control
to automatically search up/down for a available station from the current frequency.
2) Briefly press the UP/DN button on the front panel or the >>| / |<< button on the remote control
to manually search up or down with step by step for your desired station from the current
frequency.
1. When playing a DVD disc , press the SEARCH button to display a interface
and highlight the title item, then use the number buttons to input the serial
number of the title; use the direction buttons to highlight the chapter item,
then use the number buttons to input the serial number of the chapter; you
can still use the direction buttons to highlight the time item, then use the
number buttons to input the desired time to start playback; finally press the
OK or PLAY button to play the selected chapter or play from the selected
time.
3. APS BUTTON
In RADIO mode:
1) By long pressing the APS button, the radio searches from the lowest frequency and checks
the signal strength level until 1 cycle search is finished. then the 6 strongest stations are
preset to the corresponding preset number memory bank. The AS operation is implemented in
each bank of the selected band. When the AS operation is finished, it will resume broadcasting
on the M1.(It can store 3x6 stations for FM and 2x6 stations for AM in all)
2) When briefly pressing the APS button on the front panel or the remote control, the radio
searches for each preset station from the M1. When the field strength level is more than the
threshold level of the stop level, the radio is holding at that preset number for few seconds with
releasing mute, and then searches again. After finishing a circle of searching, it will stop
searching on the M1.
2. When playing a VCD/MP3/WMA/CD disc , press the SEARCH button to
display a interface and highlight the track item, then use the number buttons
to input the serial number of the track; you can still use the direction buttons
to highlight the time item, then use the number buttons to input the desired
time to start playback; finally press the OK or PLAY button to play the selected
track or play from the selected time.
NOTE: In FM band, FM1,FM2,FM3 is checked one at a time.
In AM band, AM1, AM2 is checked one at a time.
5.7 Playback in Random
4. PRESET STATION [ 1-6 ] BUTTONS
When playing DVD/VCD(PBC OFF)/MP3/WMA/CD disc , press the RDM
button to switch between RANDOM (ON)/RANDOM OFF. When in RANDOM
(ON) mode, it will play in random.
In RADIO mode:
1) To memorize the current frequency on the current band, long press any one of the six preset
buttons (1-6) .
2) To recall the preset memory on the current band, press one of the preset buttons [1-6] .
5.8 Playback in Different Angle
5. STEREO/MONO BUTTON
Press the ST button on the remote control to select the STEREO or MONO sound mode for
FM band.
1. When playing a VCD/MP3/WMA/CD disc , the ANGLE button on the remote
control is not available.
6. LOC BUTTON
1) In RADIO mode, when the signal of the distance radio station is very weak and the receiving
effect is bad during tuning, check whether there is the word LOC on LCD. If there is the word
LOC on LCD, press this button to turn off the LOC function, then tune again for the distance
radio station;
2. When playing a DVD disc , press the ANGLE button repeatedly on the
remote control to view in different angle.(This function is only for the DVD
discs with ANGLE function)
2) In RADIO mode, when the signal of the local radio station is too strong to lead that the
interference to the receiving effect during tuning, press this button to turn on the LOC function
to display the word LOC on LCD, then tune again for the local radio station.
5.9 Playback in Zoom Mode
In DVD/VCD mode, during playback, press the ZOOM button continuously
to enlarge a certain area of the images on the screen with these multiples:
During slow forward, press the PLAY button to resume normal playback.
This function is only for video.
4. Basic Disc, USB or MMC/SD Operation
4.1 Begin playback
5.3 Playback with still frame
1. To connect an external monitor to this unit.
Connect the video output of this unit to the video input of the external
monitor, and select the right video input on the menu of the external
monitor.
If the unit is currently playing DVD/VCD disc, press the STEP button
consecutively to display the still frame forward with step by step.
Press the PLAY button to resume normal playback.
?
Common Question
Q: There is nothing displayed on the monitor when the DVD player is
turned on. How to solve this problem?
5.4 Playback Repeatedly
5.4.1 ONE/ALL Repeat
A: Ensure that the monitor was set to right video input(not TV channel); for
example, if you make VIDEO1 INPUT of the monitor and DVD player
connected
with each other, then you need to set the monitor input to VIDEO1.
1. In the mode of DVD disc playback:
Press the RPT button to select REP CHAPTER, REP TITLE, REP ALL
or REP OFF.
2. Press the RELEASE button to drop down the front panel.
2. In the mode of VCD(PBC OFF)/CD disc playback:
press the RPT button to select REP ONE, REP ALL or OFF.
When it is in the state of PBC ON, during VCD disc playing, the RPT
button are not available.
3. Insert a disc into the DISC SLOT(Label surface up), then flip up the
front panel till hearing a clip.
3. In the mode of MP3/WMA disc playback:
Press the RPT button to select REP ONE, REP DIR, REP ALL or OFF.
! NOTE
5.4.2 A-B Repeat
1. Discs that are scratched, poorly manufactured or recorded in low quality,
may not play.
Press the A-B button if you want to repeat a specific segment on a disc
that you define:
2. If the player cannot read disc under normal condition, please try to
eject and reload the disc again.
1. Press the A-B button at a point (A) where you want it to be the start point
of the repeat segment. Press the A-B button again at a point (B) where you
want it to be the terminal point of the repeat segment. Then it will play the
segment repeatedly.
3. Remark:
1) In addition to normal CD and DVD, this unit supports to play CD-R,
CD-R/W, DVD-R and DVD-R/W as well; however, depending on the
conditions of the recording equipment, recording program or the disc
itself, some CD-R, CD-R/W, DVD-R or DVD-R/W may not play.
2. To cancel the A-B repeat mode and resume normal playback, press the A-B
button for the third time.
Note:
2) When dealing with CD-R, CD-R/W, DVD-R or DVD-R/W recording,
too high speed recording may result in poor signal quality and therefore,
we recommend selecting the lowest recording speed as possible.
During VCD/MP3/WMA/CD playback, points A and B must be within the
same track.
During DVD playback, points A and B can be selected from different chapters.
4.2 Pause Playback
In VCD mode
When playing a DVD/VCD/CD/MP3/WMA disc , press the PAUSE button on
remote control to pause the playback, press the PLAY button to resume normal
playback.
1. When starting to turn on the PBC function, it will play from the beginning of
the disc till it display the PBC menu on monitor if the disc include the PBC
menu.
2. Press the number buttons to select your desired track to play.
4.3 Stop Playback
In MP3/WMA mode
1. The root menu is displayed on the monitor screen all the time(and the TITLE
When playing a DVD/VCD/MP3/WMA/CD disc , press the STOP button once to
pause the playback, then press the PLAY button to resume the normal playback;
press the STOP button twice to full stop the playback, then press the PLAY
button to start playback from the beginning of the first chapter/track.
or MENU button is not available).
2. Press the direction buttons to select your desired FOLDER, then press the
OK or PLAY button to open the FOLDER, and then press the direction buttons
to select your desired file, finally press the OK button to play the selected file.
In CD mode, the TITLE, PBC, MENU buttons are disabled.
4.4 Select Chapter/Track with the UP/DN or the >>| / |<< Button
Press the UP/DN button on the front panel or the >>| / |<< button on the remote
control during playback to select the next or previous chapter/track to playback.
4.7 Terminate the Playback
Note: Press the UP/DN or the >>|/|<< button multiple times to advance multiple
chapters/tracks forward or backward.
1. Press the RELEASE button to flip down the front panel , then press the
EJECT button to eject disc, and then remove the disc and flip up the front
panel till hearing a clip.
4.5 Select Chapter/Track with the Number Buttons
2. Long press the POWER button on the front panel or briefly press the POWER
button on the remote control to turn off the DVD player.
When playing a DVD/VCD(PBC OFF)/MP3/WMA/CD disc , press one of the 1~9
and the 0/10 number buttons on the remote control to directly select and play the
1st to 10th track/chapter (the 0/10 button is used as the 10 button).
5. Advanced Disc, USB or MMC/SD Operation
If you want to play the track/chapter that serial number is bigger than 10, use the
10+, 1~9 and 0/10 button. Example 1, to play the 13th track/chapter, first press
the 10+ button once, then press the 3 button. Example 2, to play the 34th track/
chapter, first press the 10+ button for 3 times, then press the 4 button.(the 0/10
button is used as the 0 button)
5.1 Playback with Speed
During normal playback, long press the UP/DN button on the front panel or
the >>|/|<< button on the remote control continuously to fast forwards
or backwards at the following speeds: x2, x4, x8, x20, normal.
Note: long pressing the +10 or -10 button can play the next 10 or previous 10
chapter/track(only for MP3/WMA).
During speed playback, press the PLAY button to resume normal playback.
5.2 Playback with Slow Speed
4.6 Select Chapter/Track with the Root/PBC Menu (If the disc includes the
root/PBC menu)
When playing a DVD disc
During playback , press the SLOW_FWD button to execute the Slow
Forward function.
1. Press the TITLE button on the remote control to display the title list.
2. Press the direction buttons to select your desired title, and then press the OK
or PLAY button to open the root menu of the selected title.
3. Press the direction buttons to select your desired chapter, finally press the
OK or PLAY button to play the selected chapter.
With each consecutive pressing of the SLOW_FWD button, the playback
speed decreases. The speed levels in Slow Forward are as follows:
x1/2,x1/3,x1/4,x1/5,x1/6,x1/7,normal.
During playback, pressing the MENU button can directly display the root
menu of the title that is playing.
|