AutoDome Junior HD
VJR Series
en Installation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Table of Contents | en
3
Table of Contents
1
Safety
8
8
1.1
1.2
1.3
1.4
Important Safety Instructions
Safety Precautions
11
11
18
Important Notices
Customer Support and Service
2
Unpacking
19
19
20
20
2.1
2.2
2.3
Parts List
Safety Rules
Installation Notes
3
Description
21
4
Installing a Surface Mount
Description
23
23
24
24
26
30
4.1
4.1.1
4.1.2
4.1.3
4.1.4
Additional Tools Required
Preparing the Surface Mount for an Indoor Installation
Preparing the Surface Mount for an Outdoor Installation
Installing the Camera to the Mounting Plate
5
Installing a Wall Mount
34
34
34
35
38
41
5.1
Description
5.1.1
5.1.2
5.1.3
5.1.4
Additional Tools Required
Preparing the Wall Mount for an Indoor or Installation
Preparing the Wall Mount for an Outdoor Installation
Installing the Camera to the Mounting Plate
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
4
en | Table of Contents
AutoDome Junior HD
6
Installing a Recessed Mount
46
46
47
47
48
51
55
56
56
61
6.1
Description
6.2
Indoor Recessed Installation
6.2.1
6.2.2
6.2.3
6.3
Additional Requirements
Preparing the Ceiling for Installation
Installing the Camera to the Mounting Plate
Outdoor and IP54 Recessed Installation
Installation Requirements
6.3.1
6.3.2
6.3.3
Preparing the Ceiling for Installation
Installing the Camera to the Mounting Plate
7
Installing a Pipe Mount
66
66
67
67
74
7.1
Description
7.1.1
7.1.2
7.1.3
Tools/Supplies Required
Preparing the Ceiling for Installation
Installing the Camera to the Mounting Plate
8
Preparing the Wiring
77
77
78
79
8.1
8.2
8.2.1
8.2.2
8.3
Power
Connecting the Power
Power Connections to Indoor/Outdoor Cameras
Power Connections to Heater (all outdoor models)
Ethernet Connection
80
81
9
Audio, Alarms and Relay Connections
Alarm Input
82
82
83
83
84
85
85
85
9.1
9.2
Connecting Alarms (inputs 1 through 2)
Connecting a Normally Open Alarm
Connecting a Normally Closed Alarm
Alarm Outputs
9.2.1
9.2.2
9.3
9.3.1
9.4
Connecting an Open Collector Output
Audio Cables
10
Getting Started
87
10.1
Powering On
87
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Table of Contents | en
5
11
Using the IP Interface
88
89
11.1
11.2
11.3
11.4
11.4.1
11.5
11.5.1
11.5.2
11.6
11.7
11.8
11.9
11.10
Overview of Features
System Requirements
90
Connecting the AutoDome Junior HD to the PC
Configuring the AutoDome Junior HD Camera
Changing the Network Settings
The Livepage
91
92
93
95
Entering a Keyboard Control Command
Using Special Functions
100
102
103
104
104
105
105
Commissioning the AutoDome Junior Fixed Camera
Saving Snapshots
Recording Video Sequences
Processor Load
The PLAYBACK Page
12
Configuring the AutoDome Junior HD
Basic Mode: Device Access
Basic Mode: Date/Time
Basic Mode: Network
Basic Mode: Encoder
Basic Mode: Audio
Basic Mode: Recording
Basic Mode: System Overview
Advanced Mode: General
Identification
108
109
111
111
113
114
115
115
115
115
117
118
120
120
121
123
123
124
128
131
132
135
12.1
12.2
12.3
12.4
12.5
12.6
12.7
12.8
12.9
12.10
12.11
12.12
12.13
12.14
12.15
12.16
12.17
12.18
12.19
12.20
12.21
Password
Date/Time
Advanced Mode: Web Interface
Appearance
Livepage Functions
Logging
Installer Menu
Encoder Profile
Encoder Streams
Privacy Masks
Camera Settings
Lens Settings
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
6
en | Table of Contents
AutoDome Junior HD
12.22
12.23
12.24
12.25
12.26
12.27
12.28
12.29
12.30
12.31
12.32
12.33
12.34
12.35
12.36
12.37
12.38
12.39
12.40
12.41
12.42
12.43
12.44
12.45
12.46
PTZ Settings
137
138
139
140
141
141
141
142
142
142
145
148
148
150
150
150
154
160
161
162
163
163
164
165
165
166
166
167
170
172
174
175
176
176
178
178
Diagnostics
Preposition and Tours
Sectors
Miscellaneous
Logs
Audio
Pixel Counter
Advanced Mode: Recording
Storage Management
Recording Profiles
Retention Time
Recording Schedule
Recording Status
Advanced Mode: Alarm
Alarm Connections
VCA
Alarm E-Mail
Alarm Task Editor
Alarm Rules
Advanced Mode: Interfaces
Alarm Inputs
Relay
Advanced Mode: Network
Network Access
12.46.1 IPv4
12.46.2 IPv6
12.46.3 Detailed Settings
12.47
12.48
12.49
12.50
12.51
12.52
12.53
12.54
Advanced
Multicast
FTP Posting
IPv4 Filter
Advanced Mode: Service
Maintenance
Licenses
System Overview
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Table of Contents | en
7
13
14
Keyboard Commands by Number
179
181
Preventive Maintenance
15
Troubleshooting
182
182
184
15.1
15.2
AutoDome Junior Operation and Control
LED Diagnostics
16
BVIP Firmware Updates
185
185
186
16.1
16.2
Upgrading the AutoDome Junior IP or HD
Beginning the Firmware Update Process
Index
187
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
8
en | Safety
AutoDome Junior HD
1
Safety
1.1
Important Safety Instructions
Read, follow, and retain for future reference all of the following
safety instructions. Heed all warnings on the unit and in the
operating instructions before operating the unit.
1. Cleaning - Unplug the unit from the outlet before cleaning.
Follow any instructions provided with the unit. It is
generally sufficient to use a dry cloth for cleaning, but a
moist lint-free cloth or leather shammy may also be used.
Do not use liquid cleaners or aerosol cleaners.
2. Heat sources - Do not install the unit near any heat
sources such as radiators, heaters, stoves, or other devices
(including amplifiers) that produce heat.
3. Ventilation - Any openings in the unit housing are provided
for ventilation to prevent overheating and ensure reliable
operation. Do not block or cover these openings. Do not
place the unit in an enclosure unless proper ventilation is
provided, or the manufacturer's instructions have been
adhered to.
4. Water - Do not use this unit near water, for example near a
bathtub, washbowl, sink, laundry basket, in a damp or wet
basement, near a swimming pool, or in any area classified
as a wet location. To reduce the risk of fire or electrical
shock, do not expose this unit to rain or moisture.
5. Object and liquid entry - Never push objects of any kind
into this unit through openings, as they may touch
dangerous voltage points or short out parts, which could
result in a fire or electrical shock. Never spill liquid of any
kind on the unit. Do not place objects filled with liquids,
such as vases or cups, on the unit.
6. Lightning - For added protection during a lightning storm,
or when leaving this unit unattended and unused for long
periods, unplug the unit from the wall outlet and
disconnect the cable system. This will prevent damage to
the unit from lightning and power line surges.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Safety | en
9
7. Control adjustment - Adjust only those controls specified
in the operating instructions. Improper adjustment of
other controls may cause damage to the unit. Use of
controls or adjustments, or performance of procedures
other than those specified, may result in hazardous
radiation exposure.
8. Overloading - Do not overload outlets and extension cords.
This can cause fire or electrical shock.
9. Power disconnect - Units with or without ON/OFF
switches have power supplied whenever the power cord is
inserted into the power source; however, the unit is
operational only when the ON/OFF switch is in the ON
position. The power cord is the main power disconnect
device for switching off the voltage for all units.
10. Power sources - Operate the unit only via the type of
power source indicated on the label. Before proceeding,
be sure to disconnect the power from the cable being
connected to the unit.
–
–
–
For battery powered units, refer to the operating
instructions.
For units supplied by an external power source, use
only the recommended or approved power supplies.
For limited power source units, this power source
must comply with EN60950. Substitutions may
damage the unit or cause fire or shock.
–
For 24 VAC units, the VG4-A-PSUxx Power Supply is
recommended to comply with EN 50130-4 Main
Supply Voltage Dips and Short Interruption
requirement and voltage applied to the unit's power
input should not exceed +/- 10% or 21.6-26.4 VAC.
User-supplied wiring must comply with local electrical
codes (Class 2 power levels). Do not ground the
supply at the terminals or at the unit's power supply
terminals.
–
If unsure of the type of power supply to use, contact
your dealer or local power company.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
10 en | Safety
AutoDome Junior HD
11. Servicing - Do not attempt to service this unit yourself.
Opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified
service personnel.
12. Damage requiring service - Unplug the unit from the main
AC power source and refer servicing to qualified service
personnel when any damage to the equipment has
occurred, for example if:
–
–
the power supply cord or plug is damaged
exposure to moisture, water, and/or inclement
weather (rain, snow etc.)
–
–
–
liquid has been spilled in or on the equipment
an object has fallen into the unit
the unit has been dropped or the unit cabinet is
damaged
–
–
the unit exhibits a distinct change in performance
the unit does not operate normally when the user
correctly follows the operating instructions.
13. Replacement parts - Be sure the service technician uses
replacement parts specified by the manufacturer, or that
they have the same characteristics as the original parts.
Unauthorized substitutions may cause fire, electrical
shock, or other hazards.
14. Safety check - Safety checks should be performed on
completion of service or repairs to the unit, to ensure that
the unit is in proper operating condition.
15. Installation - Install in accordance with the manufacturer's
instructions and in accordance with applicable local codes.
16. Attachments, changes, or modifications - Only use
attachments/accessories specified by the manufacturer.
Any change to or modification of the equipment not
expressly approved by Bosch could void the warranty or, in
the case of an authorization agreement, authority to
operate the equipment.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Safety | en 11
1.2
Safety Precautions
DANGER!
This symbol indicates an imminently hazardous situation such
as “Dangerous Voltage” inside the product. If not avoided, this
will result in an electrical shock, serious bodily injury, or death.
WARNING!
Indicates a potentially hazardous situation. If not avoided, this
may result in minor or moderate injury. Alerts the user to
important instructions accompanying the unit.
CAUTION!
Indicates a potentially hazardous situation. If not avoided, this
may result in damage to property or risk of damage to the unit.
NOTICE!
This symbol indicates information or a company policy that
relates directly or indirectly to the safety of personnel or
protection of property.
1.3
Important Notices
Accessories - Do not place this unit on an unstable stand,
tripod, bracket, or mount. The unit may fall, causing serious
injury to persons and/or severe damage to the unit. Use only
with the cart, stand, tripod, bracket, or table specified by the
manufacturer. When a cart is used, exercise caution and care
when moving the cart/apparatus combination to avoid tipping it
over, which could result in injury. Quick stops, excessive force,
or uneven surfaces may cause the cart/unit combination to
overturn. Mount the unit in line with the manufacturer's
instructions.
All-pole power switch - Incorporate an all-pole power switch,
with a contact separation of at least 3 mm in each pole, into the
electrical installation of the building. If it is needed to open the
housing for servicing and/or other activities, use this all-pole
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
12 en | Safety
AutoDome Junior HD
switch as the main disconnect device for switching off the
voltage to the unit.
Camera grounding - When mounting the camera in potentially
damp environments, ensure the system is grounded through
the metal housing of the unit (see section: Connecting the
Power).
Camera signal - Protect the cable with a primary protector if
the camera signal is over 140 feet, in accordance with NEC800
(CEC Section 60).
Coax grounding:
–
Ground the cable system if connecting an outside cable
system to the unit.
–
Connect equipment to the unit's inputs only after this unit
has had its grounding plug connected to a grounded outlet
or its ground terminal is properly connected to a ground
source.
–
–
Disconnect the unit's input connectors from equipment
before disconnecting the grounding plug or grounding
terminal.
Follow proper safety precautions, such as grounding, for
any device connected to this unit.
U.S.A. models only - Section 810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information regarding proper
grounding of the mount and supporting structure, grounding of
the coax to a discharge unit, size of grounding conductors,
location of discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode.
Your Bosch product was developed and manufactured with
high-quality material and components that can be recycled and
reused. This symbol means that electronic and electrical
appliances that have reached the end of their service life must
be collected and disposed of separately from household waste
material. Separate collecting systems are usually in place for
disused electronic and electrical products. Please dispose of
these units at an environmentally compatible recycling facility,
in line with European Directive 2002/96/EC.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Safety | en 13
Environmental statement - Bosch has a strong commitment to
the environment. This unit has been designed to respect the
environment as much as possible.
Electrostatic-sensitive device - Take proper CMOS/MOS-FET
handling precautions to avoid electrostatic discharge.
NOTE: You must wear grounded wrist straps and observe
proper ESD safety precautions when handling the electrostatic-
sensitive printed circuit boards.
Fuse rating - For security protection of the device, the branch
circuit protection must be secured with a maximum fuse rating
of 16 A. This must be in accordance with NEC800 (CEC Section
60).
Grounding and polarization - This unit may be fitted with a
polarized alternating current line plug (a plug with one blade
wider than the other blade). This safety feature allows the plug
to fit into the power outlet in only one way. If unable to insert
the plug fully into the outlet, contact a locally certified
electrician to replace the obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
Alternatively, this unit may be fitted with a 3-pole grounding
plug (a plug with a third pin for earth grounding). This safety
feature allows the plug to fit into a grounded power outlet only.
If unable to insert the plug into the outlet, contact a locally
certified electrician to replace the obsolete outlet. Do not
defeat the safety purpose of the grounding plug.
Outdoor signals - The installation for outdoor signals, especially
regarding clearance from power and lightning conductors and
transient protection, must be in accordance with NEC725 and
NEC800 (CEC Rule 16-224 and CEC Section 60).
Moving - Disconnect the power before moving the unit. Move
the unit with care.
PoE - Never supply power via the Ethernet connection (PoE)
when power is already supplied via the power connector.
Permanently connected equipment - Incorporate a readily
accessible disconnect device in the building installation wiring.
Pluggable equipment - Install the socket outlet near the
equipment so it is easily accessible.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
14 en | Safety
AutoDome Junior HD
Power disconnect - Units have power supplied whenever the
power cord is inserted into the power source. The power cord
is the main power disconnect for all units.
Power lines - Do not locate the camera near overhead power
lines, power circuits, electrical lights, or anywhere where it
might come into contact with power lines, circuits, or lights.
SELV
All the input/output ports are Safety Extra Low Voltage (SELV)
circuits. SELV circuits should only be connected to other SELV
circuits.
Because the ISDN circuits are treated like telephone-network
voltage, avoid connecting the SELV circuit to the Telephone
Network Voltage (TNV) circuits.
Video loss - Video loss is inherent to digital video recording;
therefore, Bosch Security Systems cannot be held liable for any
damage that results from missing video information. To
minimize the risk of lost digital information, Bosch Security
Systems recommends multiple, redundant recording systems,
and a procedure to back up all analog and digital information.
NOTICE! This is a class A product. In a domestic environment
this product may cause radio interference, in which case the
user may be required to take adequate measures.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Safety | en 15
FCC & ICES INFORMATION
(U.S.A. and Canadian Models Only)
This device complies with part 15 of the FCC Rules. Operation is
subject to the following conditions:
–
–
this device may not cause harmful interference, and
this device must accept any interference received,
including interference that may cause undesired operation.
Note
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules and ICES-003 of Industry Canada. These limits are
designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and radiates
radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct
the interference at his expense.
Intentional or unintentional modifications not expressly
approved by the party responsible for compliance shall not be
made. Any such modifications could void the user's authority to
operate the equipment. If necessary, the user should consult
the dealer or an experienced radio/television technician for
corrective action.
The user may find the following booklet, prepared by the
Federal Communications Commission, helpful: How to Identify
and Resolve Radio-TV Interference Problems. This booklet is
available from the U.S. Government Printing Office,
Washington, DC 20402, Stock No. 004-000-00345-4.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
16 en | Safety
AutoDome Junior HD
INFORMATIONS FCC ET ICES
(modèles utilisés aux États-Unis et au Canada uniquement)
Ce produit est conforme aux normes FCC partie 15. La mise en
service est soumises aux deux conditions suivantes:
–
cet appareil ne peut pas provoquer d'interférence nuisible
et
–
cet appareil doit pouvoir tolérer toutes les interférences
auxquelles il est soumit, y compris les interférences qui
pourraient influer sur son bon fonctionnement.
AVERTISSEMENT: Suite à différents tests, cet appareil s’est
révélé conforme aux exigences imposées aux appareils
numériques de Classe A en vertu de la section 15 du règlement
de la Commission fédérale des communications des États-Unis
(FCC). Ces contraintes sont destinées à fournir une protection
raisonnable contre les interférences nuisibles quand l'appareil
est utilisé dans une installation commerciale. Cette appareil
génère, utilise et émet de l'energie de fréquence radio, et peut,
en cas d'installation ou d'utilisation non conforme aux
instructions, générer des interférences nuisibles aux
communications radio. L’utilisation de ce produit dans une
zone résidentielle peut provoquer des interférences nuisibles.
Le cas échéant, l’utilisateur devra remédier à ces interférences
à ses propres frais.
Au besoin, l’utilisateur consultera son revendeur ou un
technicien qualifié en radio/télévision, qui procédera à une
opération corrective. La brochure suivante, publiée par la
Commission fédérale des communications (FCC), peut s’avérer
utile : « How to Identify and Resolve Radio-TV Interference
Problems » (Comment identifier et résoudre les problèmes
d’interférences de radio et de télévision). Cette brochure est
disponible auprès du U.S. Government Printing Office,
Washington, DC 20402, États-Unis, sous la référence n° 004-
000-00345-4.
AVERTISSEMENT: Ce produit est un appareil de Classe A. Son
utilisation dans une zone résidentielle risque de provoquer des
interférences. Le cas échéant, l’utilisateur devra prendre les
mesures nécessaires pour y remédier.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Safety | en 17
Disclaimer
Underwriter Laboratories Inc. (“UL”) has not tested the
performance or reliability of the security or signaling aspects of
this product. UL has only tested fire, shock and/or casualty
hazards as outlined in UL's Standard(s) for Safety for Information
Technology Equipment, UL/IEC 60950-1. UL Certification does
not cover the performance or reliability of the security or
signaling aspects of this product.
UL MAKES NO REPRESENTATIONS, WARRANTIES, OR
CERTIFICATIONS WHATSOEVER REGARDING THE
PERFORMANCE OR RELIABILITY OF ANY SECURITY OR
SIGNALING-RELATED FUNCTIONS OF THIS PRODUCT.
Copyright
This user guide is the intellectual property of Bosch Security
Systems, Inc. and is protected by copyright.
All rights reserved.
Trademarks
All hardware and software product names used in this
document are likely to be registered trademarks and must be
treated accordingly.
NOTICE!
This user guide has been compiled with great care and the
information it contains has been thoroughly verified. The text
was complete and correct at the time of printing. The ongoing
development of the products may mean that the content of the
user guide can change without notice. Bosch Security Systems
accepts no liability for damage resulting directly or indirectly
from faults, incompleteness or discrepancies between the user
guide and the product described.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
18 en | Safety
AutoDome Junior HD
1.4
Customer Support and Service
If this unit needs service, contact the nearest Bosch Security
Systems Service Center for authorization to return and shipping
instructions.
Service Centers
USA
Repair Center
Telephone: 800-566-2283
Fax: 800-366-1329
E-mail: [email protected]
Customer Service
Telephone: 888-289-0096
Fax: 585-223-9180
E-mail: [email protected]
Technical Support
Telephone: 800-326-1450
Fax: 585-223-3508 or 717-735-6560
E-mail: [email protected]
Canada
Telephone: 514-738-2434
Fax: 514-738-8480
Europe, Middle East, Africa Region
Repair Center
Telephone: 31 (0) 76-5721500
Fax: 31 (0) 76-5721413
E-mail: [email protected]
Asia Region
Repair Center
Telephone: 65 63522776
Fax: 65 63521776
E-mail: [email protected]
Warranty and additional information
For additional information and warranty queries, please contact
your Bosch Security Systems representative or visit our website
at www.boschsecurity.com.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Unpacking | en 19
2
Unpacking
This equipment should be unpacked and handled with care. If
an item appears to have been damaged in shipment, notify the
shipper immediately. Verify that all the parts listed in the Parts
List are included. If any items are missing, notify your Bosch
Security Systems Sales or Customer Service Representative.
The original packing carton is the safest container in which to
transport the unit and must be used if returning the unit for
service. Save it for possible future use.
2.1
Parts List
The AutoDome Junior HD includes the following components:
–
–
One (1) PTZ or Fixed Dome camera
One (1) accessory kit including
–
–
–
One (1) 2-wire camera power cable, red and black
wires
One (1) 2-wire heater power cable, white/red and
white/black wires (outdoor models only)
One (1) 4-wire alarm in/out cable
–
–
–
One (1) mounting plate
One (1) outdoor installation kit (outdoor models only)
One (1) user manual
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
20 en | Unpacking
AutoDome Junior HD
2.2
Safety Rules
To ensure safety, the following warnings are specified:
–
–
–
–
The device must be installed and maintained by skilled
technical personnel.
Connect the device to a power source corresponding to
the indications given on the marking label.
Use only the attachments/accessories specified by the
manufacturer.
Unplug the device during lightning storms or when unused
for long periods of time.
–
–
Do not use the device near water (indoor models only).
Do not use the device in the presence of flammable
substances.
–
Do not allow children or unauthorized personnel to use the
device.
–
–
Do not block any ventilation openings.
Keep this manual for future reference.
2.3
Installation Notes
–
This manual contains instructions for installing an
AutoDome Junior HD in indoor and outdoor applications.
Installations in an outdoor environment require an Outdoor
AutoDome Junior HD PTZ camera and the outdoor
installation kit.
–
–
The AutoDome Junior HD Fixed camera is not suitable for
an outdoor installation.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Description | en 21
3
Description
The AutoDome Junior is part of a larger building block for any
surveillance/security system. By using multiple keyboard
controllers and multiple dome cameras, no place is too large for
monitoring. Extensible and flexible architecture facilities
remote control functions for a variety of external switching
devices such as multiplexers and DVRs (see the figure below).
1
3
4
2
6
7
12
5
13
15
8
P
ro
d
M
o
n
C
lr
S
h
o
t
1
4
2
5
3
6
9
7
0
8
9
10
14
11
9
Figure 3.1 System Configuration
1
2
3
4
5
6
7
8
9
Alarm Input (sensor)
Multiplexer
RS-485 Cable
Junction Box
AutoDome Junior
AutoDome Junior
AutoDome Junior
RS-485 Cable
Monitor
12 AutoDome Junior HD
13 Network
14 Computer
15 Encoder/Decoder
10 Keyboard
11 DVR
Refer to Section 11 Using the IP Interface, page 88 for software
and infrastructure requirements for an AutoDome Junior HD
installation.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
22 en | Description
AutoDome Junior HD
This installation should be made by qualified service personnel
and conform to the National Electrical Code and applicable
local codes.
NOTICE!
A grounded conduit is required in order to meet the EMC
Regulation Requirements.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Surface Mount | en 23
4
Installing a Surface Mount
4.1
Description
This chapter details how to mount the AutoDome Junior to a
hard surface. The AutoDome Junior is also suitable for wall
(Section 5 Installing a Wall Mount, page 34), recess
(Section 6 Installing a Recessed Mount, page 46), and pipe
mounting (Section 7 Installing a Pipe Mount, page 66). For
specific directions on mounting the unit, see the manual that
came with your mount.
For an outdoor installation you must obtain the Surface Mount
Adapter (VEZ-A2-JC or VEZ-A2-JW) and the gaskets and O-rings
supplied with an AutoDome Junior Outdoor Camera to ensure a
water-tight environment inside the unit and to maintain an IP
Environmental Protection Rating. Refer to
Section 4.1.3 Preparing the Surface Mount for an Outdoor
Installation, page 26, to start an outdoor installation.
NOTICE!
The image sensors in modern cameras are highly sensitive and
require special care for proper performance and extended
lifetime. Follow the guidelines for optimum results with your
camera:
–
Do not expose to direct sunlight or bright spotlights in
operating and nonoperating conditions.
–
Avoid bright lights in the field of view of the camera. Bright
lights cause a “smearing” effect, which is visible as white
lines above and below the highlight. Prolonged exposure to
bright lights may cause bleaching of the sensor's color
filters. This will be visible as colored spots in the picture
and is irreversible.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
24 en | Installing a Surface Mount
AutoDome Junior HD
4.1.1
Additional Tools Required
–
–
–
Appropriate straight slot screwdrivers
No. 2 Phillips screwdriver
Appropriate tool for cutting a hole in drywall or ceiling tile
(if applicable)
–
4 in. x 4 in. Junction box with 90 mm (3.54 in.) mount
holes (indoor installation)
–
–
–
One (1) ground
T-10 Torx wrench
Four (4) M4 or #10 pan head screws of an appropriate
length to screw deep enough into the surface, required for
an outdoor installation
–
–
VEZ-A2-JW or VEZ-A2-JC Surface Mount Adapter, required
for an outdoor installation
AutoDome Junior Outdoor Camera, required for an
outdoor installation
4.1.2
Preparing the Surface Mount for an Indoor
Installation
The following instructions detail the preparation necessary to
prepare the surface and the steps to install a Surface Mount.
1. Determine a secure location for the surface mount dome.
ø
175.0
(6.89)
166.9
(6.57)
R64.2
(2.53)
Figure 4.1 Indoor Surface Mount Dimensions
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Surface Mount | en 25
2. Install a 4 in. gang box or square metal junction box (not
supplied). Ensure junction box and mounting screws are
capable of supporting a maximum load of 11.33 kg
(25 pounds).
90 mm
(3.54 in.)
Figure 4.2 Install User-supplied Junction Box
3. Secure the mounting plate to the junction box with the
user supplied hardware (see Figure 4.3).
4
0 .
0
m
m
Figure 4.3 Install the Mounting Plate
1
2
3
4
Junction Box Holes
Cable Hole (40 mm maximum); Crescent Shape
Mounting Plate
Junction Box
4. Skip to Section 4.1.4 Installing the Camera to the Mounting
Plate, page 30, to continue the installation.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
26 en | Installing a Surface Mount
AutoDome Junior HD
4.1.3
Preparing the Surface Mount for an Outdoor
Installation
The following instructions detail the preparation necessary to
prepare the surface and the steps to install the Surface Mount
Adapter for an outdoor application.
1. Determine a secure location for the surface mount adapter
and the dome. The illustration below shows the placement
of the surface mount adapter (item 1, below) and the
dome (item 2).
ø
175.0
(6.89)
207.2
(8.16)
R64.2
(2.53)
Figure 4.4 Outdoor Surface Mount with AutoDome Easy HD
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Surface Mount | en 27
2. Use the VEZ-A2-JC or VEZ-A2-JW Surface Mount Adapter as
a template to mark the location of the four (4) M4 or #10
pan head screws (Item 1, below).
Figure 4.5 Location of M4 or #10 pan head screws
3. Drill the four (4) holes in the installation location. Use a
minimum screw length of 10 mm (.39 in.).
4. Prepare the surface so that it can support a maximum load
of 11.33 kg (25 lbs).
5. Thread the four (4) 3.97 mm I.D. by Ø1.78 mm O-rings
(Item 3, Figure 4.6) onto the four (4) M4 or #10 user-
supplied pan head screws. The O-rings are supplied with
the AutoDome Junior Outdoor Camera.
6. Ensure that the gasket is attached to the retaining ring. If
the gasket and the retaining ring are separate:
a. Locate the flat side of the gasket and the recessed
side of the retaining ring.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
28 en | Installing a Surface Mount
AutoDome Junior HD
b. Thread the flat side of the gasket (item 1, below) onto
the recessed side of the retaining ring (item 2). The
illustration below shows a cross-section of the gasket
on the retaining ring.
CAUTION!
You must ensure that the gasket is attached to the retaining
ring as shown above to ensure an environmentally tight seal.
7. Attach the retaining ring with gasket (item 2, below) to the
Surface Mount Adapter. These parts are supplied with the
AutoDome Junior Outdoor Camera. Ensure that the side of
the retaining ring with the counter-sunk screw holes is
facing you.
Figure 4.6 O-ring and retaining ring placement for outdoor
installation
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Surface Mount | en 29
1
2
3
4
M3 – .5 x 6 Phillips flat head machine screws
(supplied with AutoDome Junior Outdoor Camera)
Retaining ring with gasket
(supplied with AutoDome Junior Outdoor Camera)
O-ring, 3.97 mm I.D. by Ø1.78 mm
(supplied with AutoDome Junior Outdoor Camera)
User-supplied M4 or #10 pan head screws
8. Determine the side of the Surface Mount Adapter in which
the external wires are to be routed and remove the plug
from the knockout.
9. Apply a 1/2-inch (15-mm) NPS fitting to the chosen
knockout. Ensure a water-tight fitting to maintain the IP
Environmental Protection Rating for the unit.
10. Attach the Surface Mount Adapter to the surface using four
(4) user-supplied M4 or #10 pan head screws (screws not
supplied). Use a minimum screw length of 10 mm (.39 in.).
Note: For an outdoor installation ensure that the four (4)
3.97 mm I.D. by Ø1.78 mm O-rings are threaded onto the
four (4) M4 or #10 user-supplied pan head screws. Refer to
step 5.
Figure 4.7 Attach surface mount to ceiling
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
30 en | Installing a Surface Mount
AutoDome Junior HD
11. Route the external wires through the conduit and into the
Surface Mount Adapter.
CAUTION!
All wires for installation applications must be routed through a
grounded conduit.
12. Secure the mounting plate to the Surface Mount Adapter
with the three (3) M4 – .7 x 8 Phillips pan head machine
screws.
Figure 4.8 Install the Mounting Plate
1
2
Junction Box Holes
Cable Hole (40 mm maximum); Crescent Shape
13. Skip to Section 4.1.4 Installing the Camera to the Mounting
Plate, page 30, to continue the installation.
4.1.4
Installing the Camera to the Mounting Plate
To install the camera to the mounting plate for a surface or
suspended ceiling, do the following:
1. Route wires on side of mounting plate with crescent
shaped cut-out (Ref. #2 Figure 4.3).
2. Attach grounding wire from unit to junction box.
3. Attach user supplied ground to junction box.
4. Connect the mating connectors with the flying leads to the
user supplied wiring (see Section 8 Preparing the Wiring,
page 77 for wiring information).
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Surface Mount | en 31
5. Unlock the single safety locking screw on the base of the
unit using the user-supplied Allen wrench.
Figure 4.9 Unlock Safety Locking Screw
6. Plug the matching connectors from the camera into the
mating connectors from the ceiling.
Figure 4.10 Connect Cables
1
2
3
Locking Screw
Vertical Tab
Mounting Plate
7. Align wires on side of mounting plate with crescent shaped
cut-out.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
32 en | Installing a Surface Mount
AutoDome Junior HD
8. Attach the camera to the mounting plate by inserting the
vertical tab on the plate (item 1, below) into the recessed
slot on the top of the camera dome (Item 3) to the right of
the safety locking screw (item 2).
Note: Do not loosen the three brass buttons (item 4).
These brass buttons engage the slotted tabs (item 5) on
the mounting plate.
Figure 4.11 Tab/Slot Alignment Detail
1
2
3
4
5
Vertical Tab (on mounting plate)
Locking Screw
Recessed Slot (on dome housing)
Brass Button (total of three on housing)
Slotted Tab (total of three on mounting plate)
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Surface Mount | en 33
9. Rotate the camera approximately 15 degrees in a
clockwise direction to lock firmly into place, as shown in
the next illustration.
5
Figure 4.12 Attach Dome to Mounting Plate
1
Vertical tab
10. Secure the safety locking screw with the user supplied
locking torx wrench (T-10).
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
34 en | Installing a Wall Mount
AutoDome Junior HD
5
Installing a Wall Mount
5.1
Description
This chapter details how to mount the AutoDome Junior to a
wall. The AutoDome Junior is also suitable for surface
(Section 4 Installing a Surface Mount, page 23), recess
(Section 6 Installing a Recessed Mount, page 46), and pipe
mounting (Section 7 Installing a Pipe Mount, page 66). For
specific directions on mounting the unit, see the manual that
came with your mount.
For an outdoor installation you must obtain the gaskets and O-
rings supplied with an AutoDome Junior Outdoor Camera to
ensure a water-tight environment inside the unit and to
maintain an IP Environmental Protection Rating. Refer to
Section 5.1.3 Preparing the Wall Mount for an Outdoor
Installation, page 38, to start an outdoor installation.
NOTICE!
The image sensors in modern cameras are highly sensitive and
require special care for proper performance and extended
lifetime. Follow the guidelines for optimum results with your
camera:
–
Do not expose to direct sunlight or bright spotlights in
operating and nonoperating conditions.
–
Avoid bright lights in the field of view of the camera. Bright
lights cause a “smearing” effect, which is visible as white
lines above and below the highlight. Prolonged exposure to
bright lights may cause bleaching of the sensor's color
filters. This will be visible as colored spots in the picture
and is irreversible.
5.1.1
Additional Tools Required
–
–
–
–
Appropriate straight slot screwdrivers
No. 2 Phillips screwdriver
T-10 Torx wrench
AutoDome Junior Outdoor Camera, required for an
outdoor installation
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Wall Mount | en 35
5.1.2
Preparing the Wall Mount for an Indoor or
Installation
Use the following instructions to mount to an indoor wall.
1. Determine a secure location for the wall mount (supplied
separately).
NOTICE!
The fasteners and mounting surface must be capable of
supporting a maximum load of 11.33 kg (25 pounds).
366.0
(14.1)
333.0
(13.11)
220.4
(8.68)
291.0
(11.46)
Figure 5.1 Wall Mount Dimensions
2. Fit a user-provided metal single-gang junction box to the
wall.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
36 en | Installing a Wall Mount
AutoDome Junior HD
3. Attach a grounded metal conduit to the junction box
clamp.
Figure 5.2 Metal Conduit
4. Feed the wires through the conduit.
5. Feed all wires from the metal junction box through the
arm.
6. Attach the mounting cap to the arm.
7. Fit the arm to a metal single-gang junction box.
Figure 5.3 Fit to Gang Junction Box
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Wall Mount | en 37
8. Secure with the appropriate user-provided SEMS screws
that have an integral lock washer to dig through the paint
and ensure an electrical ground connection to the arm
housing or ground lug.
NOTICE!
The metal junction box and mounting surface must be capable
of supporting a maximum load of 11.33 kg (25 pounds).
9. Skip to Section 5.1.4 Installing the Camera to the Mounting
Plate, page 41, to continue the installation.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
38 en | Installing a Wall Mount
AutoDome Junior HD
5.1.3
Preparing the Wall Mount for an Outdoor
Installation
The following instructions detail the surface preparations and
the steps to install the Wall Mount for an outdoor application.
1. Determine a secure location for the wall mount (supplied
separately).
NOTICE!
The fasteners and mounting surface must be capable of
supporting a maximum load of 11.33 kg (25 pounds).
366.0
(14.1)
333.0
(13.11)
220.4
(8.68)
291.0
(11.46)
Figure 5.4 Wall Mount Dimensions
2. Use the four (4) holes at the end of the Wall Mount as a
template to mark the position where the holes should be
drilled to secure the mount.
3. Drill the four (4) holes in the installation location, screws
not supplied. Use a minimum screw length of 10 mm
(.39 in.).
4. Drill a fifth hole (maximum of 20 mm) in the center of the
four-hole pattern used to mount the arm.
5. Ensure that the gasket is attached to the retaining ring. If
the gasket and the retaining ring are separate:
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Wall Mount | en 39
a. Locate the flat side of the gasket and the recessed
side of the retaining ring.
b. Thread the flat side of the gasket (item 1, below) onto
the recessed side of the retaining ring (item 2). The
illustration below shows a cross-section of the gasket
on the retaining ring.
CAUTION!
You must ensure that the gasket is attached to the retaining
ring as shown above to ensure an environmentally tight seal.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
40 en | Installing a Wall Mount
AutoDome Junior HD
6. Attach the mounting cap to the arm. Using the AutoDome
Junior Outdoor Installation Kit, apply the following O-ring
and the retaining ring to the locations specified below:
Figure 5.5 O-ring and retaining ring placement for outdoor
installation
1
2
3
O-ring; 21.82 mm I.D. by Ø3.00 mm
Retaining ring with gasket
M3 – .5 x 6 Phillips flat head machine screws
a. Thread the 21.82 mm I.D. by Ø3.00 mm O-ring (item 1,
above) onto the lower arm threads.
b. Secure the retaining ring gasket (item 2, above) to the
dome cap with the three (3) M3 – .5 x 6 Phillips flat
head machine screws. Ensure that the side of the
retaining ring with the counter-sunk screw holes is
facing you.
c. Attach the dome cap to the arm mount.
7. Feed the wires through the hole in the surface, through the
wall mount flat gasket (item 1, Figure 5.6) and then
through the arm.
CAUTION!
All wires for installation applications must be routed through a
grounded conduit.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Wall Mount | en 41
8. Place the Wall Mount flat gasket (item 1, below), between
the surface and Wall Mount; then secure the mount using
four (4) appropriate user-provided fasteners such as Moly
or Toggle bolts. The flat gasket is supplied with the
AutoDome Junior Outdoor Camera.
Figure 5.6 Secure arm to wall with flat gasket
9. Skip to Section 5.1.4 Installing the Camera to the Mounting
Plate, page 41, to continue the installation.
5.1.4
Installing the Camera to the Mounting Plate
To install the camera to the mounting plate, do the following:
1. Attach the mounting plate (supplied with dome) to the
dome mounting cap with the three (3) screws supplied.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
42 en | Installing a Wall Mount
AutoDome Junior HD
4
0
.0 mm
1.57 in.
Figure 5.7 Attach Mounting Plate to Dome Cap
1
2
Cable Hole (40 mm maximum; crescent shape)
Mounting Screws for Dome Cap
2. Route wires on side of mounting plate with crescent
shaped cut-out (Ref. #2 Figure 5.7).
3. Attach grounding wire from unit to the mounting cap.
4. Attach user supplied ground to junction box.
5. Connect the mating connectors with the flying leads to the
user supplied wiring (see the Section 8 Preparing the
Wiring, page 77 for wiring information).
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Wall Mount | en 43
6. Unlock the single safety locking screw on the base of the
unit using the user-supplied Allen wrench.
Figure 5.8 Unlock Safety Locking Screw
7. Plug the matching connectors from the camera into the
mating connectors from the ceiling.
Figure 5.9 Connect Cables
8. Align wires on side of mounting plate with crescent shaped
cut-out.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
44 en | Installing a Wall Mount
AutoDome Junior HD
9. Attach the camera to the mounting plate by inserting the
vertical tab on the plate (item 1, below) into the recessed
slot on the top of the camera dome (Item 3) to the right of
the safety locking screw (item 2).
Note: Do not loosen the three brass buttons (item 4).
These brass buttons engage the slotted tabs (item 5) on
the mounting plate.
Figure 5.10 Tab/Slot Alignment Detail
1
2
3
4
5
Vertical Tab (on mounting plate)
Locking Screw
Recessed Slot (on dome housing)
Brass Button (total of three on housing)
Slotted Tab (total of three on mounting plate)
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Wall Mount | en 45
10. Rotate the camera approximately 15 degrees in a
clockwise direction to lock firmly into place, as shown in
the next illustration. Note: Do not loosen brass mounting
buttons.
Figure 5.11 Attach Dome to Mounting Plate
11. Secure the safety locking screw with the user supplied
locking torx wrench (T-10).
12. Pull excess wire back into the mount tube.
13. Confirm that the housing is electrically grounded.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
46 en | Installing a Recessed Mount
AutoDome Junior HD
6
Installing a Recessed Mount
6.1
Description
This chapter details how to install an AutoDome Junior into an
indoor ceiling space or into an outdoor soffit. You must use the
VJR-A3-IC54 AutoDome Junior IP54-rated In-ceiling mount kit
(sold separately) if your indoor application must be plenum
rated or rated to the IP54 standard. All outdoor recessed
applications must use the VJR-A3-IC54 kit.
The AutoDome Junior is also suitable for surface
(Section 4 Installing a Surface Mount, page 23), wall
(Section 5 Installing a Wall Mount, page 34), and pipe mounting
(Section 7 Installing a Pipe Mount, page 66). For specific
directions on mounting the unit, see the manual that came with
your mount.
NOTICE!
The image sensors in modern cameras are highly sensitive and
require special care for proper performance and extended
lifetime. Follow the guidelines for optimum results with your
camera:
–
Do not expose to direct sunlight or bright spotlights in
operating and nonoperating conditions.
–
Avoid bright lights in the field of view of the camera. Bright
lights cause a “smearing” effect, which is visible as white
lines above and below the highlight. Prolonged exposure to
bright lights may cause bleaching of the sensor's color
filters. This will be visible as colored spots in the picture
and is irreversible.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Recessed Mount | en 47
6.2
Indoor Recessed Installation
NOTICE!
This section provides instructions for installing an AutoDome
Junior into an indoor ceiling space that does not require an
IP54 or a plenum rating. Refer to Section 6.3 Outdoor and IP54
Recessed Installation, page 55, for an indoor installation that
requires these certifications.
This section details the steps to install an AutoDome Junior into
an indoor ceiling space using the VJR-A3-IC AutoDome Junior
HD Indoor In-ceiling Mount.
6.2.1
Additional Requirements
–
–
–
Appropriate straight slot screwdrivers
No. 2 Phillips screwdriver
Appropriate tool for cutting a hole in drywall or ceiling tile
(if applicable)
–
–
–
4 in. x 4 in. junction box (optional)
T-10 Torx wrench
VJR-A3-IC AutoDome Junior In-ceiling mount kit (required
accessory, sold separately)
–
VJR-A3-SP, support kit for VJR-A3-IC mounting kit, if
mounting to a drop ceiling (optional accessory)
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
48 en | Installing a Recessed Mount
AutoDome Junior HD
6.2.2
Preparing the Ceiling for Installation
To mount to a recess mount, do the following:
1. Determine a secure location for the recessed mount
(supplied separately).
104.9
(4.13)
71.6
(2.82)
mm
(in.)
229.0
(9.02)
Figure 6.1 Recess Mount Dimensions
2. Drill or cut a 200 mm hole with a tolerance of 2.2 mm (7.9
in. 1/8).
3. Optional: if installing the AutoDome Junior HD to a
suspended ceiling tile or any other surface where
additional support is required, the VJR-A3-SP mounting kit
is recommended (supplied separately).
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Recessed Mount | en 49
4. Align holes of mounting plate (supplied with dome) with
mounting bracket and attach with screws. Ensure that
both the crescent shape of the mounting plate and the
crescent shape of the mounting bracket are aligned.
Figure 6.2 Attach Mounting Plate to Mounting Bracket
1
2
3
4
5
Mounting Bracket
Mounting Plate
Clamping Plate
Crescent Shape
Clamp Drive Screw
5. Loosen the two clamp drive screws (item 5, above) so that
the clamping plates move freely.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
50 en | Installing a Recessed Mount
AutoDome Junior HD
6. Insert mount through the hole in the ceiling. Slide clamps
out and down so that the ceiling/drywall is captured in
between the clamps and the bracket flange. The ceiling/
drywall must have a maximum thickness of 41.7 mm
(1.64 in.) and an minimum thickness of 12.7 mm (0.50 in.).
Figure 6.3 Attach Recess Mount to Ceiling
7. Tighten both clamps using the clamp drive screws
(installed on the assembly) and a #2 Phillips screwdriver.
Figure 6.4 Tighten Mounting Clamps
NOTICE!
Over-torquing the ceiling clamps can damage the clamp or
ceiling. Only tighten the clamp until it contacts the ceiling and
you start to feel some resistance. If using a power screwdriver,
set the torque level to the lowest setting.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Recessed Mount | en 51
NOTICE!
If you need to install the VJR-A3-SP Support Bracket, refer to
the guide included with the bracket. Once the bracket is
installed, continue with the next section.
6.2.3
Installing the Camera to the Mounting Plate
To install the base to a surface or suspended ceiling using the
supplied mounting plate, do the following:
1. Loosen the single safety locking screw on the base of the
unit using the user-supplied T-10 Torx wrench.
Figure 6.5 Unlock Safety Locking Screw
CAUTION!
All wires for installation applications must be routed through a
grounded conduit.
2. Remove the screw from the Earth ground ( )on the top
of the mounting bracket.
3. Attach a user-supplied ground wire to the Earth ground
(
) screw hole on the mounting bracket and secure with
the screw.
4. Attach the green grounding wire from the unit to the
grounded ( ) screw hole on the mounting bracket using
the attached captive screw washer.
5. Route wires on the side of mounting plate with the
crescent shaped cut-out.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
52 en | Installing a Recessed Mount
AutoDome Junior HD
6. Connect the mating connectors (supplied in the accessory
kit) with the flying leads to the user supplied wiring (see
the Section 8 Preparing the Wiring, page 77 for wiring
information).
7. Plug the matching connectors from the camera into the
mating connectors from the ceiling.
Figure 6.6 Match Connectors
1
2
3
4
Locking Screw
Crescent Shape
Mounting Plate
Vertical Tab
8. Attach the camera to the mounting plate by inserting the
vertical tab on the plate (item 1, below) into the recessed
slot on the top of the camera dome (Item 3) to the right of
the safety locking screw (item 2).
Note: Do not loosen the three brass buttons (item 4).
These brass buttons engage the slotted tabs (item 5) on
the mounting plate.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Recessed Mount | en 53
Figure 6.7 Tab/Slot Alignment Detail
1
2
3
4
5
Vertical Tab (on mounting plate)
Locking Screw
Recessed Slot (on dome housing)
Brass Button (total of three on housing)
Slotted Tab (total of three on mounting plate)
9. Rotate the camera approximately 15 degrees in the
clockwise direction. Then, lock firmly into place, as shown
in the next illustration.
Figure 6.8 Attach Dome to Mounting Plate
1
2
3
Recess Mounting Bracket
Mounting Plate
Mounting Bracket Tether Point
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
54 en | Installing a Recessed Mount
AutoDome Junior HD
10. Ensure unit is centered.
NOTICE!
The recessed mounting bracket is provided with an additional
safety tether point. To prevent injury, attach a safety wire from
a secure anchor point above the ceiling to this tether point.
11. Align trim ring so the four alignment posts (item 1, below)
align with the recesses in the camera housing (item 2) and
so the two safety screws align with the off center holes
(item 3) on the locking clamps.
Note: The two (2) sets of raised stand-off tabs (item 4) on
each side of the trim ring align with the locking clamps.
Figure 6.9 Align Trim Ring
1
2
3
4
Alignment Tabs (four)
Align tabs to the recessed areas on the housing
Align safety locking screws to these connections
Stand-off Tabs (two)
12. Snap trim ring into place. Ensure snaps are secure by
attempting to lightly turn unit. Note: Unit should not turn.
13. Use a T-10 Torx wrench to secure the trim ring’s two (2)
safety locking screws to the mounting bracket.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Recessed Mount | en 55
6.3
Outdoor and IP54 Recessed Installation
This section details the steps to install an AutoDome Junior into
an indoor ceiling space that requires IP54 or a plenum rating or
into an outdoor soffit. This installation requires the use of the
VJR-A3-IC54 AutoDome Junior IP54-rated In-ceiling mount kit
(sold separately).
CAUTION!
The combined weight of the camera and ceiling mount is
approximately 3.76 kg (7 lb). Check that the ceiling or soffit
material is strong enough to support this weight.
The ceiling must have a maximum thickness of 41.7 mm (1.64
in.) and a minimum thickness of 12.7 mm (0.50 in.).
Mounting Assembly
The following illustrations shows the components of the recess
mount:
Figure 6.10 AutoDome Junior with IP54-rated In-ceiling Mount
1
2
3
4
VJR-A3-JW Junction Box
Mounting Bracket
AutoDome Junior Camera
Trim Skirt
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
56 en | Installing a Recessed Mount
AutoDome Junior HD
6.3.1
Installation Requirements
–
–
–
Appropriate straight slot screwdrivers
No. 2 Phillips screwdriver
Appropriate tool for cutting a hole in drywall, ceiling tile, or
other materials used in outdoor soffits (if applicable)
T-10 Torx wrench
–
–
Retaining ring with gasket
(supplied with AutoDome Junior camera kit)
Three (3) M3 – .5 x 6 Phillips flat head machine screws for
use with the retaining ring
–
(supplied with AutoDome Junior camera kit)
VJR-A3-IC54 AutoDome Junior IP54-rated In-ceiling mount
kit (required accessory, sold separately)
VJR-A3-SP, support kit for VJR-A3-IC54 mounting kit, if
mounting to a drop ceiling (optional accessory)
–
–
6.3.2
Preparing the Ceiling for Installation
To mount to a recess mount, do the following:
1. Determine a secure location for the recessed mount.
145
(5.7)
70
(2.8)
mm
(in.)
229
(9.0)
Figure 6.11 Recess Mount Dimensions
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Recessed Mount | en 57
2. Drill or cut a 200 mm hole with a tolerance of 2.2 mm
(7.9 in. 1/8).
3. Optional: if installing the AutoDome Junior to a suspended
ceiling tile or any other surface where additional support is
required, the VJR-A3-SP mounting kit is recommended
(supplied separately).
4. Ensure that the gasket is attached to the retaining ring. If
the gasket and the retaining ring are separate:
a. Locate the flat side of the gasket and the recessed
side of the retaining ring.
b. Thread the flat side of the gasket (item 1, below) onto
the recessed side of the retaining ring (item 2). The
illustration below shows a cross-section of the gasket
on the retaining ring.
CAUTION!
You must ensure that the gasket is attached to the retaining
ring as shown above to ensure an environmentally tight seal.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
58 en | Installing a Recessed Mount
AutoDome Junior HD
5. Attach the retaining ring with gasket (item 2, below,
supplied with the AutoDome Junior camera) to the VJR-A3-
JW. Ensure that the side of the retaining ring with the
counter-sunk screw holes is facing you.
Figure 6.12 O-ring and retaining ring placement for outdoor
installation
1
2
M3 – .5 x 6 Phillips flat head machine screws
(supplied with AutoDome Junior Camera)
Retaining ring with gasket
(supplied with AutoDome Junior Camera)
6. Determine the side of the VJR-A3-JW in which the external
wires are to be routed and remove the plug from the
knockout.
7. Apply a 1/2-in. (15-mm) NPS fitting to the chosen
knockout. Ensure a water-tight fitting to maintain the IP
Environmental Protection Rating for the unit.
8. Align the holes of the VJR-A3-JW with the mounting
bracket. Note the alignment of the VJR-A3-JW relative to
the bracket in Figure 6.13 below to ensure that the VJR-A3-
JW knockouts are not covered by the bracket arms.
9. Thread the four (4) 3.97 mm I.D. by Ø1.78 mm O-rings
(item 1, Figure 6.13) onto the four (4) M4 x 16 Phillips Pan
Head Machine Screws (item 2).
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Recessed Mount | en 59
10. Attach the VJR-A3-JW to the mounting bracket using the
four (4) M4 x 16 Phillips Pan Head Machine Screws (item
2, below).
Figure 6.13 Attach VJR-A3-JW to Mounting Bracket
11. Align the holes of mounting plate with the VJR-A3-JW
junction box and attach with the three (3) M4–.7 x 8
Phillips Pan Head Machine Screws. Note the alignment of
the mounting plate relative to the VJR-A3-JW junction box.
Figure 6.14 Attach Mounting Plate to VJR-A3-JW
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
60 en | Installing a Recessed Mount
AutoDome Junior HD
NOTICE!
If you need to install the VJR-A3-SP Support Bracket, refer to
the guide included with the bracket. Once the bracket is
installed, continue with the next section.
12. Loosen the two clamp drive screws (item 1, below) so that
the clamping plates (item 2) move freely.
Figure 6.15 Clamp Drive Screws and Plates
13. Insert the bracket through the hole in the ceiling. Slide
clamps out and down so that the ceiling is captured in
between the clamps and the bracket flange. The ceiling
must have a maximum thickness of 41.7 mm (1.64 in.) and
a minimum thickness of 12.7 mm (0.50 in.).
Figure 6.16 Attach Recess Mount to Ceiling
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Recessed Mount | en 61
14. Tighten both clamps using the clamp drive screws
(installed on the assembly) and a #2 Phillips screwdriver.
Figure 6.17 Tighten Mounting Clamps
NOTICE!
Over-torquing the ceiling clamps can damage the clamp or
ceiling. Only tighten the clamp until it contacts the ceiling and
you start to feel some resistance. If using a power screwdriver,
set the torque level to the lowest setting.
6.3.3
Installing the Camera to the Mounting Plate
To install the base to a surface or suspended ceiling using the
supplied mounting plate, do the following:
1. Loosen the single safety locking screw on the base of the
unit using the user-supplied T-10 Torx wrench.
Figure 6.18 Unlock Safety Locking Screw
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
62 en | Installing a Recessed Mount
AutoDome Junior HD
CAUTION!
All wires for installation applications must be routed through a
grounded conduit.
2. Remove the screw from the Earth ground ( )on the
inside of the VJR-A3-JW.
3. Attach a user-supplied ground wire to the Earth ground
(
) screw hole on the VJR-A3-JW and secure with the
screw.
4. Attach the green grounding wire from the unit to the
grounded ( ) screw hole on the VJR-A3-JW using the
attached captive screw washer.
5. Route wires through the knockout on the VJR-A3-JW.
6. Connect the mating connectors (supplied in the VJR
AutoDome accessory kit) with the flying leads to the user
supplied wiring (see the AutoDome Junior Installation
Manual for complete wiring information).
7. Plug the matching connectors from the camera into the
mating connectors from the ceiling.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Recessed Mount | en 63
8. Attach the camera to the mounting plate by inserting the
vertical tab on the plate (item 1, below) into the recessed
slot on the top of the camera dome (Item 3) to the right of
the safety locking screw (item 2).
Note: Do not loosen the three brass buttons. These brass
buttons engage the slotted tabs on the mounting plate.
Figure 6.19 Tab/Slot Alignment Detail
1
2
3
Vertical Tab (on mounting plate)
Locking Screw
Recessed Slot (on dome housing)
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
64 en | Installing a Recessed Mount
AutoDome Junior HD
9. Rotate the camera approximately 15 degrees in the
clockwise direction. Then, lock firmly into place, as shown
in the next illustration.
Figure 6.20 Attach Dome to Mounting Plate
10. Ensure unit is centered.
NOTICE!
The recessed mounting bracket is provided with an additional
safety tether point (item 1, Figure 6.20). To prevent injury,
attach a safety wire from a secure anchor point above the
ceiling to this tether point.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Recessed Mount | en 65
11. Align trim ring so the four alignment posts (item 1, below)
align with the recesses in the camera housing (item 2) and
so the two safety screws align with the off center holes
(item 3) on the locking clamps.
Note: The two (2) sets of raised stand-off tabs (item 4) on
each side of the trim ring align with the locking clamps.
Figure 6.21 Align Trim Ring
1
2
3
4
Alignment Tabs (four)
Align tabs to the recessed areas on the housing
Align safety locking screws to these connections
Stand-off Tabs (two)
12. Snap trim ring into place. Ensure snaps are secure by
attempting to lightly turn unit. Note: Unit should not turn.
13. Use a T-10 Torx wrench to secure the trim ring’s two (2)
safety locking screws to the mounting bracket.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
66 en | Installing a Pipe Mount
AutoDome Junior HD
7
Installing a Pipe Mount
7.1
Description
This chapter details how to mount the AutoDome Junior to a
pipe. The AutoDome Junior is also suitable for surface
(Section 4 Installing a Surface Mount, page 23), wall
(Section 5 Installing a Wall Mount, page 34), and recess
mounting (Section 6 Installing a Recessed Mount, page 46). For
specific directions on mounting the unit, see the manual that
came with your mount.
For an outdoor installation you must obtain the gaskets and O-
rings supplied with an AutoDome Junior Outdoor Camera to
ensure a water-tight environment inside the unit and to
maintain an IP Environmental Protection Rating.
NOTICE!
The image sensors in modern cameras are highly sensitive and
require special care for proper performance and extended
lifetime. Follow the guidelines for optimum results with your
camera:
–
Do not expose to direct sunlight or bright spotlights in
operating and nonoperating conditions.
–
Avoid bright lights in the field of view of the camera. Bright
lights cause a “smearing” effect, which is visible as white
lines above and below the highlight. Prolonged exposure to
bright lights may cause bleaching of the sensor's color
filters. This will be visible as colored spots in the picture
and is irreversible.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Pipe Mount | en 67
7.1.1
Tools/Supplies Required
–
–
–
Appropriate straight slot screwdrivers
No. 2 Phillips screwdriver
Appropriate tool for cutting a hole in drywall or ceiling tile
(if applicable)
–
–
–
T-10 Torx wrench
Ground Lug (outdoor use only)
AutoDome Junior Camera, required for an outdoor
installation
7.1.2
Preparing the Ceiling for Installation
The following instructions detail the preparation necessary to
prepare the surface and the steps to install a pipe mount.
Note: Certain steps contain additional information for outdoor
installations.
1. Determine a secure hard surface location for the ceiling
pipe mount (supplied separately).
88.8
(3.5)
88.8
(3.5)
768.2
(30.24)
3/4-14 NP
SM Threads
561.2
(22.09)
Ø11.2 (4x)
(0.44)
461.2
(18.16)
Ø175.0
(6.89)
Figure 7.1 Pipe Mount Dimensions
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
68 en | Installing a Pipe Mount
AutoDome Junior HD
2. Use the four (4) holes in the flange as a template to mark
the position where the holes should be drilled to secure
the mount.
Figure 7.2 Mark Flange Holes
3. Drill the four (4) holes in the installation location, screws
not supplied, use a minimum screw length of 10 mm
(.39 in.).
CAUTION!
All wires for installation applications must be routed through a
grounded conduit.
4. Drill a fifth hole (maximum of 20 mm [.79 in.]) in the
center of the four-hole pattern used to mount the flange.
Use this hole to feed the wires through the mount.
5. Fit the flange (supplied) to the pipe.
Note: Select the pipe length of 200 mm (7.9 in.), 300 mm
(11.8 in.), or combine the two (2) pipes with the integral
coupler for 505 mm (20 in.).
Outdoor Installation: Apply the following O-rings (supplied
with the AutoDome Junior Outdoor Camera) to the
locations specified below:
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Pipe Mount | en 69
Figure 7.3 Location of O-rings for an outdoor installation
1
2
O-ring; 21.82 mm I.D. by Ø3.00 mm
O-ring; 29.74 mm I.D. by Ø3.00 mm
a. Thread a 21.82 mm I.D. by Ø3.00 mm O-ring (item 1,
above) between the flange threads and the upper
coupler threads.
b. Thread a 29.74 mm I.D. by Ø3.00 mm O-ring (item 2,
above) between any interface between a pipe and a
coupler.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
70 en | Installing a Pipe Mount
AutoDome Junior HD
6. Outdoor Installation: Ensure that the gasket is attached to
the retaining ring. If the gasket and the retaining ring are
separate:
a. Locate the flat side of the gasket and the recessed
side of the retaining ring.
b. Thread the flat side of the gasket (item 1, below) onto
the recessed side of the retaining ring (item 2). The
illustration below shows a cross-section of the gasket
on the retaining ring.
CAUTION!
You must ensure that the gasket is attached to the retaining
ring as shown above to ensure an environmentally tight seal.
7. Fit the dome cap to the bottom of the pipe.
Outdoor Installation: Apply the following O-ring and the
retaining ring (supplied with the AutoDome Junior Outdoor
Camera) to the locations specified below:
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Pipe Mount | en 71
Figure 7.4 O-ring and retaining ring placement for outdoor
installation
1
2
3
4
O-ring; 21.82 mm I.D. by Ø3.00 mm
Dome Cap
Retaining ring with gasket
M3 – .5 x 6 Phillips flat head machine screws
a. Thread the 21.82 mm I.D. by Ø3.00 mm O-ring (item 1,
above) onto the lower pipe threads.
b. Secure the retaining ring gasket (item 2, above) to the
dome cap with the three (3) M3 – .5 x 6 Phillips flat
head machine screws. Ensure that the side of the
retaining ring with the counter-sunk screw holes is
facing you.
8. Secure the flange using four (4) appropriate user-provided
fasteners such as Moly or Toggle bolts.
Outdoor Installation: Place the flat gasket (item 1, below)
between the flange and the surface before securing.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
72 en | Installing a Pipe Mount
AutoDome Junior HD
NOTICE!
The fasteners and mounting surface must be capable of
supporting a maximum load of 11.33 kg (25 pounds).
9. Pull the wires from the pipe, starting at the flange end.
Figure 7.5 Attach Pendant Pipe Mount to Ceiling
CAUTION!
Select a rigid mounting location to prevent excessive vibration
to the AutoDome Junior Camera.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Pipe Mount | en 73
10. Attach user supplied ground lug.
11. Align holes of mounting plate (supplied with dome) with
dome mounting cap and attach with the three (3) screws
supplied.
Figure 7.6 Attach Mounting Plate to Dome Cap
1
2
3
4
Crescent Shape
Ground Lug
Dome Cap
Mounting Plate
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
74 en | Installing a Pipe Mount
AutoDome Junior HD
7.1.3
Installing the Camera to the Mounting Plate
To install the camera to a ceiling mount using the supplied
mounting plate, do the following:
1. Route wires on side of mounting plate with crescent
shaped cut-out.
2. Attach grounding wire from unit to mounting cap.
3. Attach user supplied ground to junction box.
4. Connect the mating connectors with the flying leads to the
user supplied wiring (see the Section 8 Preparing the
Wiring, page 77 for wiring information).
5. Unlock the single safety locking screw on the base of the
unit using the user-supplied Allen wrench.
Figure 7.7 Unlock Safety Locking Screw
6. Plug the matching connectors from the camera into the
mating connectors from the ceiling.
7. Align wires on side of mounting plate with crescent shaped
cut-out.
8. Attach the camera to the mounting plate by inserting the
vertical tab on the plate (item 1, below) into the recessed
slot on the top of the camera dome (Item 3) to the right of
the safety locking screw (item 2).
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Installing a Pipe Mount | en 75
Note: Do not loosen brass mounting buttons.
Figure 7.8 Tab/Slot Alignment Detail
1
2
3
4
5
Vertical Tab (on mounting plate)
Locking Screw
Recessed Slot (on dome housing)
Brass Button (total of three on housing)
Slotted Tab (total of three on mounting plate)
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
76 en | Installing a Pipe Mount
AutoDome Junior HD
9. Rotate the camera approximately 15 degrees in the
clockwise direction and lock firmly into place, as shown in
the next illustration.
Figure 7.9 Attach Dome to Mounting Plate
10. Secure the safety locking screw with the user supplied
locking torx wrench (T-10).
11. Pull excess wire back into the mount tube.
12. Confirm that the housing is electrically grounded.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Preparing the Wiring | en 77
8
Preparing the Wiring
All AutoDome Junior HD units provide three standard cables: an
Ethernet cable, a 24 VAC power input cable for the camera, and
an alarm input/output cable. An Outdoor AutoDome Junior HD
unit provides an additional 24 VAC power input cable for the
heater.
The Ethernet connection carries control and video information
and can deliver power to the camera via the Power-over-
Ethernet Plus (PoE+) standard. Refer to Section 9 Audio, Alarms
and Relay Connections, page 82, for alarm connection
information.
CAUTION!
Installation should only be performed by qualified service
personnel in accordance with the National Electrical Code or
applicable local codes.
CAUTION!
All wires for installation applications must be routed through a
grounded conduit.
8.1
Power
The recommended power cable is a 2-conductor, 14-18 gage
cable, depending on the distance.
Watts
17
14 AWG 16 AWG 18 AWG
(2.5 mm) (1.5 mm) (1.0 mm)
Camera, All models
24 VAC to AutoDome Junior HD
670 ft
421 ft
265 ft
(204 m) (128 m) (81 m)
Heater, Outdoor models only
24 VAC to Heater
25
455 ft
287 ft
180 ft
(139 m) (67 m)
(55 m)
Table 8.1 Max. Wire Distance from Power Supply to AutoDome Junior HD
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
78 en | Preparing the Wiring
AutoDome Junior HD
8.2
Connecting the Power
The AutoDome Junior HD is available as an indoor or an outdoor
model. Power to the camera in all models is supplied either via
a single 24 VAC isolated power connector (red and black wires)
or via a Power over Ethernet + (PoE+, IEEE 802.3at, class 4)
connection using the existing CAT 5E Ethernet cable. Power to
the heater is supplied via a single 24 VAC isolated power
connector (white/red and white/black wires).
WARNING!
The indoor or outdoor AutoDome Junior HD camera can accept
power from the 24 VAC power input or from the Ethernet input.
Ensure that the camera receives power from only one source.
Refer to Section 8.3 Ethernet Connection, page 81, for more
information about connecting Power over Ethernet.
NOTICE!
Use certified / Listed Class 2 power supply transformer only.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Preparing the Wiring | en 79
8.2.1
Power Connections to Indoor/Outdoor Cameras
WARNING!
The indoor or outdoor AutoDome Junior HD camera can accept
power from the 24 VAC power input or from the Ethernet input.
Ensure that the camera receives power from only one source.
Refer to Section 8.3 Ethernet Connection, page 81, for more
information about connecting Power over Ethernet.
Figure 8.1 Power Cable
Ref. # Wire
Color
Red
Black
n/a
1
2
3
24 VAC
24 VAC
User-supplied Power Supply
NOTICE!
The camera unit accepts 24 VAC, 1.2 A power only. Do not
connect 120 V or 230 V to this camera.
To connect the power to indoor models:
1. Locate the cable assembly with a three (3) pin mating
connector on one end and the red and black flying leads on
the other end.
2. Connect one lead of the 24 VAC power source to the black
wire.
3. Connect the other lead of the 24 VAC power source to the
red wire.
4. Connect the green earth ground cable to a suitable
grounded conduit.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
80 en | Preparing the Wiring
AutoDome Junior HD
8.2.2
Power Connections to Heater (all outdoor models)
The heater in an outdoor AutoDome Junior HD unit accepts
power only from a single 24 VAC isolated power connector
(white/red and white/black wires). The heater does not accept
power via Power over Ethernet + (PoE+, IEEE 802.3at, class 4).
Figure 8.2 Power Cable
Ref. # Wire
Color
1
2
3
24 VAC
24 VAC
User-supplied Power Supply
White/Red
White/Black
n/a
WARNING!
The heater unit accepts 24 VAC, 2 A power only. Do not connect
120 V or 230 V to this heater.
To connect the power to outdoor unit heaters:
1. Locate the cable assembly with a three (3) pin mating
connector on one end and the white/red and white/black
flying leads on the other end.
2. Connect one lead of the ground or 24 VAC power source to
the white/black wire.
3. Connect one lead of the 24 VAC power source to the
white/red wire.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Preparing the Wiring | en 81
8.3
Ethernet Connection
The AutoDome Junior HD connects to a 10 Base-T/100 Base-TX
network either directly or via a switch. Both video and control
are transmitted over a standard TCP/IP network using the built-
in Web server. In addition, power is supplied to an AutoDome
Junior HD camera via the Ethernet cable compliant with the
Power-over-Ethernet + (IEEE 802.3at, class 4) standard.
NOTICE!
The heater in an outdoor AutoDome Junior HD unit accepts
power only from a 24 VAC power source. The heater cannot be
powered via the Power-over-Ethernet + (IEEE 802.3at, class 4)
standard.
CAUTION!
Ethernet connections must be made to non-exposed (indoor)
networks only.
Cable Type
CAT-5E or CAT 6 Ethernet
100 m (328 ft)
Maximum Distance
Bandwidth
10 Base-T/100 Base-TX
PoE+ (indoor models only) IEEE 802.3at, class 4 standard
Terminal Connector RJ45, Female
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
82 en | Audio, Alarms and Relay Connections
AutoDome Junior HD
9
Audio, Alarms and Relay
Connections
9.1
Alarm Input
All AutoDome Junior models provide connections for two alarm
inputs, one alarm output, and one audio input. Each alarm input
can be activated by dry contact devices such as pressure pads,
passive infrared detectors, door contacts, and similar devices.
Figure 9.1 Six-wire Audio and Alarm In/Out Cable
Wire Color Function
White
Brown
Orange
Green
Yellow
Blue
Alarm Out
Alarm In 1
Alarm In 2
Ground
Audio In
Audio Ground
The table below summarizes the size and distance wires.
Wire Size
Maximum Distance
AWG mm
feet
500
800
meters
152.4
243.8
22
18
0.644
1.024
Table 9.1 Alarm Wire Guide
You wire alarms either Normally Open (N.O.) or Normally
Closed (N.C.), and must program the alarm inputs N.O. (the
default) or N.C. through the AutoDome Junior main menu.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Audio, Alarms and Relay Connections | en 83
9.2
Connecting Alarms (inputs 1 through 2)
You can configure alarms 1 through 2 as Normally Open (N.O.)
or Normally Closed (N.C.) alarms.
9.2.1
Connecting a Normally Open Alarm
1. Connect the alarm to the appropriate input (1 through 2)
and ground at the AutoDome Junior.
Figure 9.2 N.O. - Normally Open
Ref. # User Contact Dome
Color
1
Normally
Alarm In 1 or Alarm In 2
Brown IN 1 or
Open
Common
(Ref. #3)
Ground (Ref. #4)
Orange IN 2
Green
2
2. From the AutoDome Junior HD Settings page select
Interface>Alarm Inputs. Refer to Section 12 Configuring the
AutoDome Junior HD, page 108, for directions about
accessing the Settings page.
AutoDome Junior Programmed N.O.
Circuit
Open
Alarm Indication
Normal
Closed
Alarm
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
84 en | Audio, Alarms and Relay Connections
AutoDome Junior HD
9.2.2
Connecting a Normally Closed Alarm
1. Connect the alarm to the appropriate input (1 through 2)
and ground at the AutoDome Junior.
Figure 9.3 N.C. Normally Closed Connections
Ref. # User Contact Dome
Color
1
Normally
Alarm In 1 or Alarm In 2
Brown IN 1 or
Closed
Common
(Ref. #3)
Ground (Ref. #4)
Orange IN 2
Green
2
2. From the AutoDome Junior HD Settings page select
Interface>Alarm Inputs. Refer to Section 12 Configuring the
AutoDome Junior HD, page 108, for directions about
accessing the Settings page.
AutoDome Junior Programmed N.C.
Circuit
Open
Alarm Indication
Alarm
Closed
Normal
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Audio, Alarms and Relay Connections | en 85
9.3
Alarm Outputs
The AutoDome Junior incorporates one (1) alarm output: an
open collector output.
NPN
C
--
--
--
--
--
--
--
--
--
--
--
--
--
-
-
-
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
B
-
-
--
--
--
--
--
--
--
-
--
--
--
--
--
--
--
E
--
--
--
--
--
--
--
--
--
--
--
--
-
--
Figure 9.4 N.O. - Normally Open
Ref. # Description
Color
n/a
White
Green
n/a
1
2
3
4
5
6
Dome
Normally Open
Ground
Alarm In
User Supplied Device (i.e. Allegiant or DVR) n/a
Ground/Common n/a
9.3.1
Connecting an Open Collector Output
Output 1 is an open collector. This output must be connected
to a positive voltage between 5 and 32 V to complete the
circuit, with a maximum voltage rating of 32 VDC @ 150 ma.
1. Connect the appropriate stripped wire to the open
collector of the transistor’s white wire.
2. Connect the appropriate stripped wire to the ground
(GND) connector.
9.4
Audio Cables
The AutoDome Junior is capable of receiving line input audio
signals and transmitting it over a network. The audio signal is
transmitted one-way and in sync with the video signal.
Refer to Section 12.5 Basic Mode: Audio, page 114.
Audio Line Input Specifications
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
86 en | Audio, Alarms and Relay Connections
AutoDome Junior HD
Max. Input Voltage
Impedance
5.5 Vpp
9 K Ω
Sample Rate
G.711: 8 bits @ 8 KHzL16: 16 bits
@ 16 kHz PCM
Shield
Bare copper braid: 95% coverage
Internal gain level adjustment is available
Wire Specifications
3
Wire Type
Coax (recommended)
10 m (33 ft)
Distance
Gage
22 AWG
Shield
Bare copper braid: 95% coverage
Center conductor Stranded bare copper
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Getting Started | en 87
10
Getting Started
Once the installation is complete, the AutoDome Junior HD can
be programmed. A typical system may include a keyboard,
matrix switcher, monitor, appropriate wiring connections, and a
PC with Internet Explorer. Please refer to the individual product
manuals for complete installation and setup instructions for
each of the system components.
10.1
Powering On
When you turn the AutoDome Junior power on there is a ten
(10) second pause before the dome starts its homing phase.
During the homing phase the camera pans left and right and
tilts up and down. It also adjusts the lens focus. The entire
homing phase lasts approximately 20 seconds and ends with a
splash screen. Refer to Section 11 Using the IP Interface,
page 88.
WARNING!
Before powering the dome on, remove the clear protective
plastic sheet on top of the bubble.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
88 en | Using the IP Interface
AutoDome Junior HD
11
Using the IP Interface
The AutoDome Junior HD transmits PTZ control commands and
images over a TCP/IP network. It also allows users to configure
the camera display settings, camera operating settings, and to
configure the network parameters.
The HD unit incorporates a network video server in the IP
module. The primary function of the server is to encode video
and control data for transmission over a TCP/IP network. With
its H.264 encoding, it is ideally suited for IP communication and
for remote access to digital video recorders and multiplexers.
The use of existing networks means that integration with CCTV
systems or local networks can be achieved quickly and easily.
Video images from a single camera can be simultaneously
received on several receivers.
Refer to Section 16 BVIP Firmware Updates, page 185, for
firmware upgrade instructions.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Using the IP Interface | en 89
11.1
Overview of Features
The AutoDome Junior HD module includes the following
functionality:
Function
Description
Video Encoding
Streaming
The camera uses the H.264 compression standards and
ensures that the data rate remains low even with high
image quality and can also be adapted to local
conditions within wide limits.
Encodes multiple data streams simultaneously
according to individually customized profiles. This
feature creates data streams that can serve different
purposes. For example, one (1) data stream for local
recording and one (1) data stream optimized for
transmission over the Local Area Network (LAN).
Multicast
Enables simultaneous, real-time transmission to
multiple receivers. The network must implement the
UDP and IGMP V2 protocols as a prerequisite for
Multicasting.
Configuration
Allows configuration for all camera settings from a Web
browser on the local network (Intranet) or on the
Internet. You can also update the firmware, load device
configurations, store configuration settings, and copy
these settings from one camera to another.
Snapshots
Record
Allows you to take and store individual video frames as
JPEG images from the Web browser interface.
Allows configuration for the recording options of the IP
module. You can record video from the Livepage to a
hard drive or you can opt to store up to 8 MB of video
on the IP module.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
90 en | Using the IP Interface
AutoDome Junior HD
11.2
System Requirements
The AutoDome Junior HD requires specific software and
hardware to allow a user to view live images and to configure
camera settings over a TCP/IP network. These requirements
are:
–
–
–
A computer with the Microsoft Windows XP, Vista, or
Windows 7 operating system, network access, and the
Microsoft Internet Explorer Web browser version 9.0 or
later, or
A computer with Microsoft Windows XP, Vista, or Windows
7 operating system, network access, and reception
software such as the Bosch Video Client, Bosch Video
Management System, or a Bosch recording solution, or
A compatible hardware decoder from Bosch Security
Systems as a receiver and a connected video monitor.
NOTICE!
The Web browser must be configured to enable Cookies to be
set from the IP address of the unit.
In Windows Vista, deactivate protected mode on the Security
tab under Internet Options.
You can find notes on using Microsoft Internet Explorer in the
online Help in Internet Explorer.
If you choose to use a computer running Microsoft Internet
Explorer or any of the Bosch software, the computer must
conform to the following minimum requirements:
–
Operating System: Windows XP (Service Pack 3), Windows
Vista or Windows 7 (32 or 64 bits)
Processor: Intel Pentium Quad Core, 3.0 GHz or
comparable
–
–
–
–
RAM: 2048 MB
Free Hard Disk Space: 10 GB
Video system: NVIDIA GeForce 8600 or higher display with
a minimum of 16-bit color
–
Network interface: 100/1000-BaseT
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Using the IP Interface | en 91
–
Software:
–
–
–
–
–
Microsoft Internet Explorer, version 9.0 or higher
Bosch Video Client (BVC)
DirectX 9.0c
MPEG-ActiveX 5.20.0045 or newer
Oracle Java Virtual Machine 1.6.0_26
NOTICE!
Ensure the graphics card is set to 16-bit or 32-bit color. If you
need further assistance, contact your PC system administrator.
11.3
Connecting the AutoDome Junior HD to
the PC
1. Install the AutoDome Junior HD according to the
instructions in the AutoDome Junior HD User Manual.
2. Connect an Ethernet cable from the AutoDome Junior HD
RJ45 connector to a dedicated network switch to bypass
the Local Area Network (LAN).
3. Connect the dedicated network switch to the RJ45
connector on the PC (see option A below).
NOTICE!
The AutoDome Junior HD can also be connected directly to a
PC using an Ethernet crossover cable with RJ45 connectors
(see option B below).
Figure 11.1 AutoDome Junior HD System Configuration
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
92 en | Using the IP Interface
AutoDome Junior HD
1
2
3
4
AutoDome Junior HD
IP Connection
Network Switch
Computer
NOTICE!
You can also use the Bosch Configuration Manager utility to
configure the network settings for an AutoDome Junior IP or HD
camera. Go to www.boschsecurity.com to download the
Configuration Manager software and Operating Manual.
11.4
Configuring the AutoDome Junior HD
Camera
To operate the camera in your network you must assign it a
valid network IP address. The default IP address is 192.168.0.1,
but you may have to change this address if it conflicts with
another device on your network. Refer to Section 12.3 Basic
Mode: Network, page 111 for more information.
To properly configure the camera for your network, you need
the following information:
–
Unit IP address: An identifier for the camera on a TCP/IP
network. For example, 140.10.2.110 is a valid syntax for an
IP address.
–
–
–
Subnet mask: A mask used to determine what subnet an IP
address belongs to.
Gateway IP address: A node on a network that serves as an
entrance to another network.
Port: An endpoint to a logical connection in TCP/IP and
UDP networks. The port number identifies the use of the
port for use through a firewall connection.
NOTICE!
Ensure that the network parameters of your cameras are
available before you begin configuration.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Using the IP Interface | en 93
The AutoDome Junior HD defaults are as follows:
–
–
–
IP Address: 192.168.0.1
Subnet Mask: 255.255.255.0
Gateway IP Address: 0.0.0.0
The following sections provide instructions about installing the
software necessary to view images over an IP connection,
configuring the IP network settings and accessing the
AutoDome Junior IP images from a Web browser.
11.4.1
Changing the Network Settings
The AutoDome Junior HD has a default IP address of
192.168.0.1. To change the IP address or any network settings,
you can use the Configuration Manager software or the
AutoDome Junior IP server.
NOTICE!
Contact your local network administrator for a valid IP address,
Subnet Mask, and a Gateway IP Address.
Using the Configuration Manager
Configuration Manager is an optional network utility provided
on the Bosch Security Systems Web site. Use the Configuration
Manager Manual to make any configuration changes.
NOTICE!
Depending on the PC network security settings, the user may
have to add the new IP address to the browser’s trusted sites
list for the AutoDome Junior HD controls to operate.
Using the AutoDome Junior HD Web Server
To configure the camera using the AutoDome Junior HD server,
do the following:
1. Set the IP address on the PC to 192.168.0.10to ensure
that the PC and the IP AutoDome are on the same Subnet.
2. Launch Microsoft Internet Explorer and navigate to the
following URL: http://192.168.0.1
The Web browser opens the LivePage for the AutoDome
Junior HD; a security warning message is displayed.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
94 en | Using the IP Interface
AutoDome Junior HD
3. Check the Always Trustbox, then click YES.
4. Click the Settings link, located at the top of the LivePage.
5. Click the Service Settings link, located in the left pane of
the Settings window.
6. Click the Network link to open the Network Settings page.
Figure 11.2 Network Settings Page
7. Configure the settings on this page based on the
addresses provided by your local network administrator.
NOTICE!
Click the Help on this page? link if you need more information.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Using the IP Interface | en 95
8. Click the Set button to save the settings.
9. Launch another instance of Microsoft Internet Explorer.
10. Type the original IP address followed by /reset (for
example, http://192.168.0.1/reset) in the address bar and
click Go to restart the AutoDome Junior IP. Once you
restart the AutoDome Junior IP, use the new IP Address to
access the LivePage.
11. Disconnect the AutoDome Junior IP Ethernet cable from
the dedicated network switch and reconnect the Ethernet
cable to the local area network (LAN).
11.5
The Livepage
Once the connection is established, the Web browser displays
the Livepage. It shows the live video image on the right of the
browser window. Depending on the configuration, various text
overlays may be visible on the live video image.
Other information may be shown next to live video image on the
Livepage. The display depends on the settings on the Livepage
Configuration page (see the AutoDome Junior IP online help).
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
96 en | Using the IP Interface
AutoDome Junior HD
Display Stamping
Various overlays or “stamps” in the video image provide
important status information. The overlays provide the
following information:
Decoding error. The frame might show artefacts due to
decoding errors. If subsequent frames reference this
corrupted frame, they might also show decoding errors
as well but won’t be marked with the “decoding error”
icon.
Alarm flag set on media item
Communication error. Any kind of communication error
is visualized by this icon. Cause can be a connection
failure to the storage medium, a protocol violation with
a sub component or simply a timeout. An automatic
reconnection procedure is started in the background in
order to recover from this error.
Gap; no video recorded
Watermarking not valid
Watermarking flag set on media item
Motion flag set on media item
Discovery of storage not completed. If the information
about recorded video is not cached, a discovery
procedure is started in order find all recorded video.
During this time, the “discovery” symbol is shown.
While discovery is executed, gaps might be shown in
places which the discovery has not yet reached. The
gap will automatically be replaced by the true video, as
soon as the correct information is available.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Using the IP Interface | en 97
Maximum Number of Connections
If you do not connect, the unit may have reached its maximum
number of connections. Depending on the unit and network
configuration, each AutoDome Junior IP can have up to 25 Web
browser connections or up to 50 connections via the Bosch
Video Management System.
Protected AutoDome Junior IP
If the AutoDome Junior HD is password protected against
unauthorized access, the Web browser displays a
corresponding message and prompts you to enter the
password when you attempt to access protected areas.
NOTICE!
An AutoDome Junior IP offers the option to limit the extent of
access using various authorization levels (see the AutoDome
Junior IP online help).
1. Enter the user name and associated password in the
corresponding text fields.
2. Click OK. If the password is entered correctly, the Web
browser displays the page that was called up.
Protected Network
If a RADIUS server is employed in the network for managing
access rights (802.1x authentication), the AutoDome Junior HD
must be configured accordingly, otherwise no communication is
possible.
Image Selection
You can view the image of the camera in different displays.
Click one of the tabs Stream 1, Stream 2, or M-JPEG
below the video image to toggle between the different
displays of the camera image.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
98 en | Using the IP Interface
AutoDome Junior HD
View Control
The View Control tab allows you to control camera functions
(pan, tilt, zoom, focus, and iris), navigate through on-screen
menus and to view preset shots. (Not applicable with the
AutoDome Junior HD Fixed camera)
Reference # Description
Reference # Description
Focus far2
Focus near2
Iris close2
1
2
3
Tilts the camera up
8
Tilts the camera down 9
Pans the camera to
10
the left
Iris open2
4
5
Pans the camera to
11
12
the right
Pans and tilts the
camera in all
directions
Sets the PTZ speed for controls 1, 2,
3, 4, 5, 6, and 7
Zoom out1
6
7
13
Moves the camera to pre-set shot
numbers 1, 2, 3, 4, 5, and 6
Zoom in1
1. This function is also accessible by using the mouse scroll wheel while in the Live video frame.
2. This button is also used as the "Enter" button to select menu items from the AUX tab.
1. To control a peripheral, click the appropriate controls.
2. Move the mouse cursor over the video image. Additional
options for controlling peripherals are displayed with the
mouse cursor.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Using the IP Interface | en 99
3. To manually pan throughout the image area, move your
cursor over any part of the live video. The image area
displays a directional arrow (
, then click and
hold the right mouse key to pan the camera.
Digital I/O
The alarm icon is for information purposes and indicates the
status of an alarm input: When an alarm is triggered, the icon
lights up blue. The device’s configuration determines whether
the alarm is displayed, as well as additional details (see the
AutoDome Junior HD online help).
Triggering Relay
You can switch connected units using the relays in the
AutoDome Junior HD (for example lights or door openers).
To activate this, click the icon for the relay next to the
video image. The icon will be red when the relay is
activated.
System Log / Event Log
The System Log field contains information about the operating
status of the AutoDome Junior IP and the connection. You can
save these messages automatically in a file (see the AutoDome
Junior online help).
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
100 en | Using the IP Interface
AutoDome Junior HD
Events such as the triggering or end of alarms are shown in the
Event Log field. You can save these messages automatically in a
file (see the AutoDome Junior online help).
1. If you want to delete the entries, click the delete icon in
the top right-hand corner of the relevant field.
2. If you want to view a detailed log, click the icon in the top
right-hand corner of the relevant field. A new window will
open.
11.5.1
Entering a Keyboard Control Command
The Aux Control tab is used to enter keyboard control
commands. These commands are composed of a command
number plus the appropriate function key (Show Shot, Set Shot
Aux On or Aux Off). A valid combination either issues a
command to the camera or displays an on-screen menu.
Aux Control Tab
The Aux Control tab is used to enter pre-programmed keyboard
control commands.
To access the Aux Control tab, navigate to the Livepage and
click the Aux Control tab (see Figure 11.3 below).
Figure 11.3 Aux Control Tab
1
2
3
4
5
6
7
8
Command number field
Keypad (numbers 0-9)
Show a preset shot
Set a preset shot
Initiates a command
Deletes a number in the Command Number field
Used to select a menu item
Stops a command
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Using the IP Interface | en 101
To Enter a Keyboard Control Command:
1. Place the cursor in the Command Number field.
2. Click the desired command number via the on-screen
keypad.
3. Click either the Aux On or the Aux Off button to initiate or
stop the command.
4. If the command initiates a menu, use the Up/Down arrows
on the View Control to navigate the menu. Click the Focus
or Iris button to select a menu item.
To Set a Preset Shot:
Preset shots (or scenes) are camera positions that are saved in
memory for future use.
1. Move your cursor over the live image and wait for the area
to display a directional arrow.
2. Click and hold a mouse button to pan to the desired
position you want to save.
3. Click any number combination from 1-64 from the on-
screen keypad to identify the scene number.
4. Click the Set Shot button. The image area displays a
message that indicates which shot number was saved.
To View a Preset Shot:
1. Click the number of the scene you want to view using the
on-screen keypad.
2. Click the Show Shot button.
NOTICE!
For more information about the AutoDome Junior HD settings
and controls, click the Help on this page? link to open the
AutoDome Junior online help.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
102 en | Using the IP Interface
AutoDome Junior HD
11.5.2
Using Special Functions
The AutoDome offers several special command buttons on the
Livepage.
Scan 360
Click this button to start a continuous 360° pan. To stop the
continuos pan, click a directional control in the View Control
tab.
Autopan
Click this button to pan the AutoDome between user-defined
limits. To set the left and right pan limits, refer to
Section 12.22 PTZ Settings, page 137, so set the Autopan limits.
To stop the continuos pan, click a directional control in the
View Control tab.
Tour A / Tour B
Click one of these buttons to start the playback of a recorded
(guard) tour. A Recorded Tour saves all manual camera
movements made during the recording, including its rate of
pan, tilt and zoom speeds and other lens setting changes. Refer
to Section 12.22 PTZ Settings, page 137, to program a recorded
tour. To stop a tour, click a directional control in the View
Control tab.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Using the IP Interface | en 103
11.6
Commissioning the AutoDome Junior
Fixed Camera
The remote commissioning feature simplifies installation by
allowing operators to position and zoom the camera via a
remote head-end unit.
This section provides instructions for setting the position and
the zoom level for an AutoDome Junior HD Fixed camera (VJR-
F801 Series).
Using the Built-in Web Server:
1. Launch Microsoft Internet Explorer and navigate to the IP
Address for the AutoDome Junior HD Fixed camera.
The Web browser opens the Livepage.
2. Type the password for the Service level user.
3. Click the SETTINGS link in the upper section of the
window.
The Web browser opens a new page with the configuration
menu.
4. Click the Advanced Link; then click the Camera link,
located in the left pane of the Settings window.
5. Click the Installer Menu, located under the Camera link.
6. Click the Open button to the right of View Control to open
the View Control window.
Note: The View Control window is disabled 15 minutes
after you open the window. If the View Control window is
disabled, you must close the window then re-open to
resume setting the camera position and zoom level.
7. Use the View Control arrow keys and the zoom keys to
establish the desired view.
Note: The AutoDome Junior HD fixed camera pans, tilts,
and zooms at a much slower rate compared to a Pan/Tilt/
Zoom dome camera.
8. Close the View Control window to set the camera’s
position and the zoom level.
9. Click the LIVEPAGE link, in the upper section of the
window.
10. To reset the position and zoom level, repeat these steps.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
104 en | Using the IP Interface
AutoDome Junior HD
11.7
Saving Snapshots
You can save individual images from the video sequence
currently shown on the Livepage in JPEG format on your
computer's hard drive. The icon for recording single images is
only visible if the unit is configured to enable this process.
Click the icon. The storage location depends on the
configuration of the AutoDome Junior HD.
11.8
Recording Video Sequences
You can save sections of the video sequence currently shown
on the Livepage on your computer's hard drive. The icon for
recording video sequences is only visible if the unit is
configured to enable this process.
1. Click the icon to start recording. The storage location
depends on the configuration of the AutoDome Junior HD.
A red dot in the icon indicates that recording is in
progress.
2. Click the icon again to stop recording.
3. To change the storage location for the recorded video,
navigate to the Livepage settings on the Settings page.
NOTICE!
You can play back saved video sequences using the Player from
Bosch Security Systems, which can be installed from the
product CD supplied.
Image Resolution
Sequences are saved at the resolution that has been preset in
the configuration for the encoder (see Section 12.3 Basic Mode:
Network, page 111).
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Using the IP Interface | en 105
11.9
Processor Load
If the AutoDome Junior IP is accessed via the Web browser, you
will see the processor load indicator in the top left of the
window next to the manufacturer's logo.
You can obtain additional information to help when you
troubleshoot or fine-tune the unit. The values indicate the
proportions of the individual functions on the encoder load,
shown as percentages.
Move the cursor over the graphic indicator. Some
additional numerical values are also displayed.
11.10 The PLAYBACK Page
The RECORDINGS page for playing back recorded video
sequences can be accessed from the LIVEPAGE and from the
SETTINGS menu.
The PLAYBACK link is only visible if a storage medium has been
selected.
Click the PLAYBACK link in the navigation bar in the upper
section of the window. The playback page appears.
Selecting Recordings
All sequences that are saved are displayed in the list. A running
number (track) is assigned to each sequence. Start time and
stop time, recording duration, number of alarms, and recording
type are displayed.
1. Click a list entry. The playback for the selected sequence
starts immediately in the video window.
2. Use the arrow buttons below the list to browse the list.
3. Select the number of entries that are displayed
simultaneously.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
106 en | Using the IP Interface
AutoDome Junior HD
Controlling a Playback
You will see a time bar below the video image for quick
orientation. A green arrow above the bar indicates the position
of the image currently being played back within the sequence.
The time bar offers various options for navigation.
Red bars indicate the points in time where alarms were
triggered. Drag the green arrow to navigate to these points
quickly.
1. You can change the time interval by clicking the zoom keys
(magnifying glass icons). The display can span a range
from two months to a few seconds.
2. Drag the green arrow to the point in time at which
playback should begin. The date and time display below
the bar provides orientation to the second.
Buttons
You can control playback by means of the buttons below the
video image. The buttons have the following functions:
Start or pause playback
Leap to the start of the active video sequence or
to the previous sequence
Leap to the start of the next video sequence
Slide Control
You can use the slide control to control playback speed.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Using the IP Interface | en 107
Bookmarks
In addition, you can set markers in the sequences, so-called
bookmarks, and leap directly to these. These bookmarks are
indicated as small yellow arrows above the time interval. Use
the bookmarks as follows:
Jump to the previous bookmark
Set bookmark
Jump to the following bookmark
NOTICE!
Bookmarks are only valid while you are in the PLAYBACK page;
they are not saved with the sequences. As soon as you leave the
page all bookmarks are deleted.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
108 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
12
Configuring the AutoDome Junior
HD
The SETTINGS page provides access to the configuration menu,
which contains all the unit's parameters arranged in groups.
You can view the current settings by opening one of the
configuration screens. You can change the settings by entering
new values or by selecting a predefined value from a list field.
There are two options for configuring the unit or checking the
current settings:
–
–
Basic mode
Advanced mode
In Basic Mode the most important parameters are arranged in
seven groups. This allows you to change the basic settings with
just a few entries and then put the device into operation.
Advanced Mode is recommended for expert users or system
support personnel. You can access all unit parameters in this
mode. Settings that affect the fundamental functionality of the
unit (such as firmware updates) can only be altered in the
advanced mode.
All parameter groups are described in this chapter in the order
in which they are listed in the configuration menu, from the top
of the screen to the bottom.
CAUTION!
The settings in the advanced mode should only be processed or
modified by expert users or system support personnel.
All settings are backed up in the AutoDome Junior HD memory
so they are not lost even if the power fails.
Starting Configuration
Click the SETTINGS link in the upper section of the
window. The Web browser opens a new page with the
configuration menu.
Navigation
1. Click one of the menu items in the left window margin. The
corresponding submenu is displayed.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 109
2. Click one of the entries in the submenu. The Web browser
opens the corresponding page.
Making Changes
Each configuration screen shows the current settings. You can
change the settings by entering new values or by selecting a
predefined value from a list field.
After each change, click Set to save the change.
CAUTION!
Save each change with the associated Set button.
Clicking the Set button saves the settings only in the current
field. Changes in any other fields are ignored.
12.1
Basic Mode: Device Access
Camera name
You can give the AutoDome Junior HD a name to make it easier
to identify. The name makes the task of administering multiple
units in larger video monitoring systems easier, for example
using the Bosch Video Management System programs.
The device name is used for the remote identification of a unit,
in the event of an alarm for example. For this reason, enter a
name that makes it as easy as possible to quickly identify the
location.
CAUTION!
Do not use any special characters, for example &, in the name.
Special characters are not supported by the system's internal
recording management and may therefore result in the Player or
Archive Player being unable to play back the recording.
Password
An AutoDome Junior HD is generally protected by a password
to prevent unauthorized access to the unit. You can use
different authorization levels to limit access.
The AutoDome Junior HD operates with three authorization
levels: service, user and live.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
110 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
The highest authorization level is service. After entering the
correct password, you can access all the functions of the
AutoDome Junior HD and change all configuration settings.
With the user authorization level, you can operate the unit and
also control cameras, for example, but you cannot change the
configuration.
The lowest authorization level is live. It can only be used to
view the live video image and switch between the different live
image displays.
You can define and change a password for each authorization
level if you are logged in as service or if the unit is not
password protected.
Enter the password for the appropriate authorization level here.
The maximum text length is 19characters.
NOTICE!
Proper password protection is only guaranteed when all higher
authorization levels are also protected with a password. If a live
password is assigned, for example, a service and a user
password must also be set. When assigning passwords, you
should therefore always start from the highest authorization
level, service, and use different passwords.
Confirm password
In each case, enter the new password a second time to
eliminate typing mistakes.
NOTICE!
A new password is only saved when you click the Set button.
You should therefore click the Set button immediately after
entering and confirming a password.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 111
12.2
Basic Mode: Date/Time
Device date/Device time/Device time zone
If there are multiple devices operating in your system or
network, it is important to synchronize their internal clocks. For
example, it is only possible to identify and correctly evaluate
simultaneous recordings when all units are operating on the
same time. If necessary, you can synchronize the unit with your
computer's system settings.
Click the Sync to PC button to copy your computer's
system time to the AutoDome Junior HD.
Time server IP address
The AutoDome Junior HD can receive the time signal from a
time server using various time server protocols, and then use it
to set the internal clock. The unit polls the time signal
automatically once every minute.
Enter the IP address of a time server here.
Time server type
Select the protocol that is supported by the selected time
server. Preferably, you should select the SNTP server as the
protocol. This supports a high level of accuracy and is required
for special applications and subsequent function extensions.
Select Time server for a time server that works with the
protocol RFC 868.
12.3
Basic Mode: Network
The settings on this page are used to integrate the AutoDome
Junior HD into an existing network.
Some changes only take effect after the unit is rebooted. In this
case, the Set button changes to Set and Reboot.
1. Make the desired changes.
2. Click the Set and Reboot button. The AutoDome Junior HD
is rebooted and the changed settings are activated.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
112 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
CAUTION!
If you change the IP address, subnet mask or gateway address,
the AutoDome Junior HD is only available under the new
addresses after the reboot.
DHCP
If a DHCP server is employed in the network for the dynamic
assignment of IP addresses, you can activate acceptance of IP
addresses automatically assigned to the AutoDome Junior HD.
Certain applications (VIDOS, Bosch Video Management System,
Archive Player, Configuration Manager) use the IP address for
the unique assignment of the unit. If you use these applications,
the DHCP server must support the fixed assignment between IP
address and MAC address, and must be appropriately set up so
that, once an IP address is assigned, it is retained each time the
system is rebooted.
IP address
Enter the desired IP address for the AutoDome Junior HD in
this field. The IP address must be valid for the network.
Subnet mask
Enter the appropriate subnet mask for the selected IP address
here.
Gateway address
If you want the unit to establish a connection to a remote
location in a different subnet, enter the IP address of the
gateway here. Otherwise leave the box blank (0.0.0.0).
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 113
12.4
Basic Mode: Encoder
Default profile
You can select a profile for encoding the video signal.
You can use this to adapt the video data transmission to the
operating environment (for example network structure,
bandwidth, data load).
Pre-programmed profiles are available, each giving priority to
different perspectives. When selecting a profile, details are
displayed in the list field.
–
–
–
–
–
–
HD High high quality / low latency
Target bit rate: 5000 kbps
Maximum bit rate: 10000 kbps
Encoding interval: 30.00 ips
High Resolution 2
Target bit rate: 1500 kbps
Maximum bit rate: 3000 kbps
Encoding interval: 30.00 ips
Low Bandwidth
Target bit rate: 700 kbps
Maximum bit rate: 1500 kbps
Encoding interval: 30.00 ips
DSL
Target bit rate: 400 kbps
Maximum bit rate: 500 kbps
Encoding interval: 30.00 ips
ISDN (2B)
Target bit rate: 80 kbps
Maximum bit rate: 100 kbps
Encoding interval: 30.00 ips
ISDN (1B)
Target bit rate: 40 kbps
Maximum bit rate: 50 kbps
Encoding interval: 30.00 ips
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
114 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
–
Modem
Target bit rate: 20 kbps
Maximum bit rate: 22 kbps
Encoding interval: 15.00 ips
GSM
–
Target bit rate: 7 kbps
Maximum bit rate: 8 kbps
Encoding interval: 7.50 ips
12.5
Basic Mode: Audio
You can set the gain of the audio signals to suit your specific
requirements. The current video image is shown in the small
window next to the slide controls to help you check the audio
source and improve assignments. Your changes are effective
immediately.
If you connect via Web browser, you must activate the audio
transmission on the Livepage Functions page (see
Section 11.5 The Livepage, page 95). For other connections, the
transmission depends on the audio settings of the respective
system.
Audio
The audio signals are sent in a separate data stream parallel to
the video data, and so increase the network load. The audio
data are encoded according to G.711 and require an additional
bandwidth of approx. 80 kbps for each connection. If you do
not want any audio data to be transmitted, select Off.
Line In
You can set the line input gain. Make sure that the display does
not go beyond the green zone during modulation.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 115
12.6
Basic Mode: Recording
You can record the images from the AutoDome Junior HD on
various local storage media or on an appropriately configured
iSCSI system.
Here you can select a storage medium and immediately start
the recording.
Storage medium
1. Select the required storage medium from the list.
2. Click the Start button to start the recording immediately.
12.7
Basic Mode: System Overview
The data on this page are for information purposes only and
cannot be changed. Keep a record of this information in case
technical assistance is required.
NOTICE!
You can select all required text on this page with the mouse and
copy it to the clipboard with the [Ctrl]+[C] key combination, for
example if you want to send it via e-mail.
12.8
12.9
Advanced Mode: General
Identification
Camera ID
Each AutoDome Junior HD should be assigned a unique
identifier that you can enter here as an additional means of
identification.
Camera Name
The camera name makes it easier to identify the remote camera
location, in the event of an alarm for example. It will be
displayed in the video screen if configured to do so. The camera
name makes the task of administering cameras in larger video
monitoring systems easier, for example using the VIDOS or
Bosch Video Management System programs.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
116 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
Enter a unique, unambiguous name for the camera in this field.
You can use both lines for this.
CAUTION!
Do not use any special characters, for example &, in the name.
Special characters are not supported by the system's internal
recording management and may therefore result in the Player or
Archive Player being unable to play back the recording.
You can use the second line for entering additional characters;
these can be selected from a table.
1. Click the icon next to the second line. A new window with
the character map is opened.
2. Click the required character. The character is inserted into
the Result field.
3. In the character map, click the << and >> icons to move
between the different pages of the table, or select a page
from the list field.
4. Click the < icon to the right of the Result field to delete the
last character, or click the X icon to delete all characters.
5. Now click the OK button to apply the selected characters
to the second line of the Camera 1 parameters. The
window will close.
Initiator extension
You can attach your own text to the initiator name of the
AutoDome Junior HD to make the unit easier to identify in large
iSCSI systems. This text is added to the initiator name,
separated from it by a full stop. You can see the initiator name
in the System Overview page.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 117
12.10 Password
An AutoDome Junior HD is generally protected by a password
to prevent unauthorized access to the unit. You can use
different authorization levels to limit access.
NOTICE!
Proper password protection is only guaranteed when all higher
authorization levels are also protected with a password. If a live
password is assigned, for example, a service and a user
password must also be set. When assigning passwords, you
should therefore always start from the highest authorization
level, service, and use different passwords.
Password
The AutoDome Junior HD operates with three authorization
levels: service, user and live.
The highest authorization level is service. After entering the
correct password, you can access all the functions of the
AutoDome Junior HD and change all configuration settings.
With the user authorization level, you can operate the unit and
also control cameras, for example, but you cannot change the
configuration.
The lowest authorization level is live. It can only be used to
view the live video image and switch between the different live
image displays.
You can define and change a password for each authorization
level if you are logged in as service or if the unit is not
password protected.
Enter the password for the appropriate authorization level here.
The maximum text length is 19characters.
Confirm password
In each case, enter the new password a second time to
eliminate typing mistakes.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
118 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
NOTICE!
A new password is only saved when you click the Set button.
You should therefore click the Set button immediately after
entering and confirming a password.
12.11 Date/Time
Date format
Select your required date format.
Device date/Device time
If there are multiple devices operating in your system or
network, it is important to synchronize their internal clocks. For
example, it is only possible to identify and correctly evaluate
simultaneous recordings when all units are operating on the
same time.
1. Enter the current date. Since the unit time is controlled by
the internal clock, there is no need to enter the day of the
week – it is added automatically.
2. Enter the current time or click the Sync to PC button to
copy your computer's system time to the AutoDome Junior
HD.
Device time zone
Select the time zone in which your system is located.
Daylight saving time
The internal clock can switch automatically between normal
and daylight saving time (DST). The unit already contains the
data for DST switch-overs up to the year 2018. You can use
these data or create alternative time saving data if required.
NOTICE!
If you do not create a table, there will be no automatic
switching. When changing and clearing individual entries,
remember that two entries are usually related to each other and
dependent on one another (switching to summer time and back
to normal time).
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 119
1. First check whether the correct time zone is selected. If it
is not correct, select the appropriate time zone for the
system, and click the Set button.
2. Click the Details button. A new window will open and you
will see the empty table.
3. Select the region or the city that is closest to the system's
location from the list field below the table.
4. Click the Generate button to generate data from the
database in the unit and enter it into the table.
5. Make changes by clicking an entry in the table. The entry is
selected.
6. Clicking the Delete button will remove the entry from the
table.
7. Select other values from the list fields below the table to
change the entry. Changes are made immediately.
8. If there are empty lines at the bottom of the table, for
example after deletions, you can add new data by marking
the row and selecting required values from the list fields.
9. Now click the OK button to save and activate the table.
Time server IP address
The AutoDome Junior HD can receive the time signal from a
time server using various time server protocols, and then use it
to set the internal clock. The unit polls the time signal
automatically once every minute.
Enter the IP address of a time server here.
Time server type
Select the protocol that is supported by the selected time
server. Preferably, you should select the SNTP server as the
protocol. This supports a high level of accuracy and is required
for special applications and subsequent function extensions.
Select Time server for a time server that works with the
protocol RFC 868.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
120 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
12.12 Advanced Mode: Web Interface
12.13 Appearance
On this page you can adapt the appearance of the web
interface and change the website language to meet your
requirements. If necessary, you can replace the manufacturer's
logo (top right) and the product name (top left) in the top part
of the window with individual graphics.
NOTICE!
You can use either GIF or JPEG images. The file paths must
correspond to the access mode (for example
C:\Images\Logo.gif for access to local files, or http://
www.mycompany.com/images/logo.gif for access via the
Internet/Intranet).
When accessing via the Internet/Intranet, ensure that a
connection is always available to display the image. The image
file is not stored in the AutoDome Junior HD.
Website language
Select the language for the user interface here.
Company logo
Enter the path to a suitable graphic if you want to replace the
manufacturer's logo. The image file can be stored on a local
computer, in the local network or at an Internet address.
Device logo
Enter the path to a suitable graphic if you want to replace the
product name. The image file can be stored on a local
computer, in the local network or at an Internet address.
NOTICE!
If you want to use the original graphics again, simply delete the
entries in the Company logo and Device logo fields.
JPEG interval
You can specify the interval at which the individual images
should be generated for the M-JPEG image on the Livepage.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 121
12.14 Livepage Functions
On this page you can adapt theLivepage functions to your
requirements. You can choose from a variety of different
options for displaying information and controls.
1. Check the box for the items that are to be made available
on the Livepage. The selected items are indicated by a
check mark.
2. Check whether the required functions are available on the
Livepage.
Transmit Audio
You can only select this option if audio transmission is actually
switched on (see Section 12.28 Audio, page 141).The audio
signals are sent in a separate data stream parallel to the video
data, and so increase the network load. The audio data are
encoded according to G.711 and require an additional
bandwidth of approx. 80 kbps for each connection.
Lease time (s)
The lease time in seconds determines the time beyond which a
different user is authorized to control the camera after no
further control signals are received from the current user. After
this time interval, the camera is automatically enabled.
Show alarm inputs
The alarm inputs are displayed next to the video image as icons
along with their assigned names. If an alarm is active, the
corresponding icon changes color.
Show relay outputs
Relay outputs are shown next to the video image as icons, along
with their assigned names. If the relay is switched, the icon
changes color.
Show VCA trajectories
When video content analysis (VCA) is activated, check this item
to show additional information that traces the path of objects.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
122 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
Show VCA metadata
When video content analysis (VCA) is activated, additional
information is displayed in the live video stream. For example,
in Motion+ mode, the sensor areas for motion detection are
marked.
Show event log
The event messages are displayed along with the date and time
in a field next to the video image.
Show system log
The system messages are displayed along with the date and
time in a field next to the video image and provide information
about establishing and ending connections, for example.
Allow snapshots
Here you can specify whether the icon for saving individual
images should be displayed below the live image. Individual
images can only be saved if this icon is visible.
Allow local recording
Here you can specify whether the icon for saving video
sequences on the local memory should be displayed below the
live image. Video sequences can only be saved if this icon is
visible.
Path for JPEG and Video files
1. Enter the path for the storage location of individual images
and video sequences that you can save from the Livepage.
2. If necessary, click Browse to find a suitable directory.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 123
12.15 Logging
Save event log
Check this option to save event messages in a text file on your
local computer.
You can then view, edit and print this file with any text editor or
the standard Office software.
File for event log
1. Enter the path for saving the event log here.
2. If necessary, click Browse to find a suitable directory.
Save system log
Check this option to save system messages in a text file on your
local computer.
You can then view, edit and print this file with any text editor or
the standard Office software.
File for system log
1. Enter the path for saving the system log here.
2. If necessary, click Browse to find a suitable directory.
12.16 Installer Menu
Main Frequency
Sets the frequency of the incoming power supply. This setting
is made at the factory and should not be changed.
Orientation
Reverses the image 180º (ideal when mounting upside down).
Set the orientation to Normal (default) or Inverted.
SC Settings
Click the Default button to restore all cameras settings to their
original defaults.
SC Data
Click the default button to clear all preposition, privacy mask,
and other user settings.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
124 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
Reboot device
Performs a reboot of the AutoDome. There is a ten (10) second
pause before the dome starts its homing phase. During the
homing phase the camera pans left and right and tilts up and
down. It also adjusts the lens focus. The entire homing phase
lasts approximately 40 seconds.
Factory defaults
Click Restore all defaults to restore the factory defaults for the
camera. A confirmation screen appears. Allow 5 seconds for the
camera to optimize the picture after a mode reset.
View Control
Click the Enable button to access the View Control window.
Use the View Control arrow keys and the zoom keys to establish
the desired view.
NOTICE!
The View Control window is disabled 15 minutes after you open
the window. If the View Control window is disabled, you must
close the window then re-open to resume setting the camera
position and zoom level.
12.17 Encoder Profile
For the video signal encoding, you can select a code algorithm
and you can change the presets for the profiles.
You can adapt the video data transmission to the operating
environment (for example network structure, bandwidth, data
load). To this end, the AutoDome Junior HD simultaneously
generates two data streams (Dual Streaming), which
compression settings you can select individually, for example
one setting for transmissions to the Internet and one for LAN
connections.
Pre-programmed profiles are available, each giving priority to
different perspectives.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
–
Configuring the AutoDome Junior HD | en 125
HD High high quality / low latency
Target bit rate: 5000 kbps
Maximum bit rate: 10000 kbps
Encoding interval: 30.00 ips
High Resolution 2
–
–
–
–
–
–
–
Target bit rate: 1500 kbps
Maximum bit rate: 3000 kbps
Encoding interval: 30.00 ips
Low Bandwidth
Target bit rate: 700 kbps
Maximum bit rate: 1500 kbps
Encoding interval: 30.00 ips
DSL
Target bit rate: 400 kbps
Maximum bit rate: 500 kbps
Encoding interval: 30.00 ips
ISDN (2B)
Target bit rate: 80 kbps
Maximum bit rate: 100 kbps
Encoding interval: 30.00 ips
ISDN (1B)
Target bit rate: 40 kbps
Maximum bit rate: 50 kbps
Encoding interval: 30.00 ips
Modem
Target bit rate: 20 kbps
Maximum bit rate: 22 kbps
Encoding interval: 15.00 ips
GSM
Target bit rate: 7 kbps
Maximum bit rate: 8 kbps
Encoding interval: 7.50 ips
You can change individual parameter values of a profile and you
can also change the name. You can switch between profiles by
clicking the appropriate tabs.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
126 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
CAUTION!
The profiles are rather complex. They include a large number of
parameters that interact with one another, so it is generally
best to use the default profiles.
Change the profiles only once you are fully familiar with all the
configuration options.
In the default setting, Stream 2 is transmitted for alarm
connections and automatic connections. Bear this fact in mind
when assigning the profile.
NOTICE!
All parameters combine to make up a profile and are dependent
on one another. If you enter a setting that is outside the
permitted range for a particular parameter, the nearest
permitted value will be substituted when the settings are
saved.
Profile name
You can enter a new name for the profile here. The name is then
displayed in the list of available profiles in the Profile name
field.
Target data rate
You can limit the data rate for the AutoDome Junior HD to
optimize utilization of the bandwidth in your network. The
target data rate should be set according to the desired picture
quality for typical scenes with no excessive motion.
For complex images or frequent changes of image content due
to frequent movements, this limit can be temporarily exceeded
up to the value you enter in the Maximum data rate field.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 127
Maximum data rate
This maximum data rate is not exceeded under any
circumstances. Depending on the video quality settings for the
I- and P-frames, this fact can result in individual images being
skipped.
The value entered here must be at least 10% higher than the
value entered in the Target data rate field. If the value entered
here is too low, it will automatically be adjusted.
Video resolution
Here you can select the desired resolution for the video image.
The following resolutions are available:
–
–
–
–
SD/240p (WQVGA)
432×240 pixels
SD/480p (WVGA)
854 x 480 pixels
720p
1280×720 pixels
1080p
1920×1080 pixels
Encoding Interval
The figure selected here determines the interval at which
images are encoded and transmitted. The image rate in ips
(images per second) is displayed next to the text field.
Use the slide bar to select a frame rate from 30.00 ips to 1 ips.
Expert Settings
Use the expert settings to adapt the I-frame quality and the P-
frame quality to specific requirements, if necessary. The setting
is based on the H.264 quantization parameter (QP).
GOP Structure
Select the structure you require for the Group of Pictures here.
Depending on whether you place greater priority on having the
lowest possible delay (IP frames only) or using as little
bandwidth possible, you can choose between IP, IBP, and IBBP.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
128 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
I-frame Distance
This parameter allows you to set the intervals in which the I-
frames will be coded. 0 means auto mode, whereby the video
server inserts I-frames as necessary. An entry of 1 indicates that
I-frames are continuously generated. An entry of 2 indicates
that only every second image is an I-frame, and 3 only every
third image etc.; the frames in between are coded as P-frames.
I-frame Quality
This setting allows you to adjust the image quality of the I-
frames. The basic setting Auto automatically adjusts the quality
to the settings for the P-frame video quality. Alternatively, you
can use the slide control to set a value between 9and51. The
value 9 represents the best image quality with, if necessary, a
lower frame refresh rate depending on the settings for the
maximum data rate. A value of 51 results in a very high refresh
rate and lower image quality.
P-frame Quality
This setting allows you to adjust the maximum image quality of
the P-frames. The basic setting Auto automatically adjusts to
the optimum combination of movement and image definition
(focus). Alternatively, you can use the slide control to set a
value between 9and51. The value 9 represents the best image
quality with, if necessary, a lower frame refresh rate depending
on the settings for the maximum data rate. A value of 51 results
in a very high refresh rate and lower image quality.
Default
Click Default to return the profile to the factory default values.
12.18 Encoder Streams
Select the property and default profile for each H.264 stream
and set the parameters for the M-JPEG stream.
The choices for Stream 1 depend on the resolution setting in
the Installer Menu page (Section 12.16 Installer Menu,
page 123).
For the first H.264 stream you can select from these options:
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 129
HD stream options:
–
–
–
H.264 MP 720p25/30 Fixed
H.264 MP 720p30/60 Fixed
H.264 MP 1080p Fixed
SD stream options (use these options if a second H.264 stream
is allowed):
–
H.264 BP+ bit-rate-limited
Select this setting when using hardware decoders or the
Divar XF digital video recorder. The bit rate is limited to
1.2 Mbps.
CABAC: off
CAVLC: on
GOP structure: IP
I-frame distance: 15
Deblocking filter: on
H.264 MP SD
–
Select this setting when using software decoders, PTZ and
for rapid movements in the images.
CABAC: on
CAVLC: off
GOP structure: IP
I-frame distance: 30
Deblocking filter: on
To select the stream options:
1. Select the required encoder properties and one of the
encoder profiles for each data stream.
2. Click the Preview button. The preview screens for both
data streams are shown.
3. Click the 1:1 Live View button below the preview screen to
open a new window with the original data stream and to
check the image quality and the transmission rate.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
130 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
Property
Select one of the H.264 standards for each stream.
NOTICE!
If you select H.264 MP 720p30/60 Fixed or H.264 MP 1080p
Fixed as the first stream, you can select only Copy of Stream 1
as an option for stream 2.
Default profile
Select one of the following profiles for each stream:
–
–
–
–
–
–
–
–
HD high quality / low latency
High resolution 2
Low bandwidth
DSL
ISDN (2B)
ISDN (1B)
Modem
GSM
Refer to Section 12.17 Encoder Profile, page 124, for more
details about each stream.
Preview
Click the Preview button to open a small static preview window
for each stream. To enlarge the preview and view live video,
click the 1:1 Live View button.
JPEG stream
Select the resolution, frame rate, and image quality parameters
for the M-JPEG stream.
–
–
Resoltuion: Select either 4CIF/D1 or CIF.
Frame rate: Select one of the following frame rates: 5, 10,
15, 20, 25, or 30 ips.
–
Picture quality: his setting allows you to adjust the image
quality. Use the slide bar to choose a quality between Low
and High.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 131
12.19 Privacy Masks
Privacy Masking is used to block out a specific area of a scene
from being viewed. Masks can be configured as a gray area with
four corners. You may define a total of 24 privacy masks.
NOTICE!
–
The AutoDome disables the Privacy Mask feature if the
orientation of the camera is set to Inverted. Refer to
Section 12.16 Installer Menu, page 123, for orientation
settings.
–
You cannot apply a privacy mask 70° (tilt direction) below
the horizon.
To add a privacy mask to a scene:
1. Navigate to the scene in which you want to apply a privacy
mask.
a. Click the View Control link.
b. Use the PTZ controls to view the scene.
2. Select the privacy mask number to apply to the scene.
The preview window displays a gray rectangle in the scene.
3. Click the Enable check box to activate the privacy mask.
The privacy mask in the preview window changes to
orange to indicate that the mask will appear in the video
streams on the Livepage.
4. Select a mask color from the Pattern list box.
5. Place the cursor inside the privacy mask area in the
preview window; then click and drag to move the privacy
mask.
6. Place the cursor on a corner or on a side of the mask
rectangle; then click and drag to expand or shrink the
privacy mask area.
NOTICE!
Draw the mask 10% larger than the object to ensure that the
mask completely covers the object as the AutoDome zooms in
and out.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
132 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
7. Click Set to save the privacy mask size and position.
An image window displays the privacy mask.
8. To hide an individual mask, select the mask number and
clear the Enable check box.
9. To hide all masks from an image view, click the Hide Masks
check box.
Note: If you choose to hide all masks, you must enable
each enable each individual mask to show the mask in the
scene.
12.20 Camera Settings
White Balance
Adjusts the color settings to maintain the quality of the white
areas of the image.
–
ATW: allows the camera to continuously adjust color
reproduction.
–
–
–
Indoor: white balance tracking for indoor use.
Outdoor: white balance tracking for outdoor use.
AWB Hold: places the ATW on hold and saves the color
settings.
–
–
Extended ATW (default): allows the camera to constantly
adjust for optimal color reproduction.
Manual: Red and Blue gain can be manually set to a
desired position.
Red Gain
The red gain adjustment offsets the factory white point
alignment (reducing red introduces more cyan).
Blue Gain
The blue gain adjustment offsets the factory white point
alignment (reducing blue introduces more yellow). It is only
necessary to change the white point offset for special scene
conditions.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 133
Gain Control
Adjusts the automatic gain control (AGC). Automatically sets
the gain to the lowest possible value needed to maintain a good
picture.
–
AGC (default): electronically brightens dark scenes, which
may cause graininess in low light scenes.
Fixed: no enhancement. This setting disables the Max.
Gain Level option.
–
If you select this option, the AutoDome Junior HD makes
the following changes automatically:
–
–
Night Mode: switches to Color
Auto Iris: switches to Constant
Max. Gain Level
Controls the maximum value the gain can have during AGC
operation. To set the maximum gain level, choose from:
–
–
–
Normal
Medium
High
Sharpness
Adjusts the sharpness of the picture. To set the sharpness, type
a value between 1 and 15 inclusive. The default setting is 12.
Shutter Mode
–
–
Off: turns the Auto SensUP Off.
AutoSensUp: increases camera sensitivity by increasing
the integration time on the CCD. This is accomplished by
integrating the signal from a number of consecutive video
frames to reduce signal noise.
If you select this option, the AutoDome Junior HD makes
the following change automatically:
–
Auto Iris: switches to Constant
Shutter
Adjusts the electronic shutter speed (AES). Controls the time
period for which light is gathered by the collecting device. The
default setting is 1x (60 Hz: 1/30, 50 Hz: 1/25).
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
134 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
Auto SensUp Maximum
Sets the Auto SensUp minimum value for the AutoDome. The
Auto SensUp Min. value is the factor by which the sensitivity of
the camera is increased. The default setting is 15x.
Backlight Compensation
Optimizes the video level for the selected area of the image.
Parts outside this area may be underexposed or overexposed.
Select On to optimize the video level for the central area of the
image. The default setting is Off.
Stabilization
Turns on video stabilization.
Night Mode
Selects night mode (B/W) to enhance lighting in low light
scenes. Select from the following options:
–
–
–
Monochrome: Forces the camera to stay in Nigh Mode and
transmit monochrome images.
Color: The camera does not switch to Night Mode
regardless of ambient light conditions.
Auto: The camera switches out of Night Mode after the
ambient light level reaches a pre-defined threshold.
Night Mode Threshold
Adjusts the level of light at which the camera automatically
switches out of night mode (B/W) operation. Select a value
between 10 and 55 (in increments of 5), where 10 is earlier and
55 is later.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 135
12.21 Lens Settings
Auto Focus
Continuously adjusts the lens automatically to the correct focus
for the sharpest picture.
–
One Push (default): activates the Auto Focus feature after
the camera stops moving. Once focused, Auto Focus is
inactive until the camera is moved again.
–
–
Auto Focus: Auto Focus is always active.
Manual: Auto Focus is inactive.
Focus Polarity
–
–
Normal (default): focus controls operate normally.
Reverse: focus controls are reversed.
Focus Speed
Controls how fast the Auto focus will readjust when the focus
becomes blurred. Select from the following options:
–
–
–
–
Super Slow
Slow
Medium
Fast
Auto Iris
Automatically adjusts the lens to allow the correct illumination
of the camera sensor. This type of lens is recommended for use
where there are low light or changing light conditions.
–
–
Constant (default): camera constantly adjusts to varying
light conditions (default).
If you select this option, the AutoDome Junior HD makes
the following changes automatically:
–
–
Gain Control: switches to AGC
Shutter Mode: switches to Normal
Manual: camera must be manually adjusted to compensate
for varying light conditions.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
136 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
Iris Polarity
Capability to reverse the operation of the iris button on the
controller.
–
–
Normal (default): iris controls operate normally.
Reverse: iris controls are reversed.
Auto Iris Level
Increases or decreases brightness according to the amount of
light. Type a value between 1 and 15, inclusive. The default
setting is 8.
Iris Speed
Controls how fast the Iris will adjust the opening according to
the illumination of the scene. Type a value between 1 and 10,
inclusive. The default setting is 5.
Maximum Zoom Speed
Controls the zoom speed. The default setting is Fast.
Zoom Polarity
Capability to reverse the operation of the zoom button on the
controller.
–
–
Normal (default): zoom controls operate normally.
Reverse: zoom controls are reversed.
Digital Zoom
Digital zoom is a method of decreasing (narrowing) the
apparent angle of view of a digital video image. It is
accomplished electronically, without any adjustment of the
camera's optics, and no optical resolution is gained in the
process. Select Off to disable or On to enable this feature. The
default setting is On.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 137
12.22 PTZ Settings
Auto Pan Speed
Continuously pans the camera at a speed between right and left
limit settings. Type a value between 1 and 60 (expressed in
degrees), inclusive. The default setting is 30.
Inactivity
Selects the time period the dome must be not controlled until
the inactivity event will be executed.
–
Off (default): camera remains on a current scene
indefinitely.
–
–
Scene 1: camera returns to Preset 1.
Previous Aux: camera returns to the previous activity.
Inactivity Period
Determines the behavior of the dome when the control for
dome is inactive. Select a time period from the pull-down list (3
sec. - 10 min.). The default setting is 2 minutes.
Auto Pivot
The Auto Pivot tilts the camera through the vertical position as
the camera is rotated to maintain the correct orientation of the
image. Set the Auto Pivot to On (default) to automatically
rotate the camera 180º when following a subject traveling
directly beneath the camera. To disable this feature, click Off.
Freeze Frame
Select On (default) to freeze the image while the AutoDome
moves to a predetermined scene position.
Autopan Left Limit
Sets the left Auto Pan limit of the camera. Use the preview
window to move the camera to the left pan limit and click the
button. The camera will not move past this limit when in Auto
Pan Between Limits mode (AUX 2 ON).
Autopan Right Limit
Sets the right Auto Pan limit of the camera. Use the preview
window to move the camera to the right pan limit and click the
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
138 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
button. The camera will not move past this limit when in Auto
Pan Between Limits mode (AUX 2 ON).
Tilt Up Limit
Sets the upper tilt limit of the camera.
Tilt Limits
Click the Reset button to clear the upper tilt limit.
Tour A / Tour B
Starts and stops the recording of a recorded (guard) tour.
The AutoDome can make up to two (2) recorded tours. A
Recorded Tour saves all manual camera movements made
during the recording, including its rate of pan, tilt and zoom
speeds and other lens setting changes.
Note: You can save a total of 15 minutes of recorded actions
between the two tours.
To record a tour:
1. Click the Start Recording button. The system prompts you
to overwrite the existing tour.
2. Click Yes to overwrite the existing tour movements.
3. Click the View Control link, under the image cameo, to
access the directional and zoom controls.
4. Use the View Control dialog box to make the necessary
camera movements.
5. Click the Stop Recording button to save all actions.
12.23 Diagnostics
Accesses the Built-in Self Test (BIST). Click the BIST button to
display the number of times the AutoDome Junior HD:
–
–
–
–
performed homing event (AutoDome Junior HD PTZ only).
failed to home properly (AutoDome Junior HD PTZ only).
restarted.
lost video.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 139
12.24 Preposition and Tours
The AutoDome Junior HD can store up to 99 preset scenes and
this section allows you to define the individual scenes and a
preposition tour comprised of the defined scenes.
You define individual preposition scenes, then use these scenes
to define the preposition tour. The tour starts from the lowest
scene number in the tour and progresses sequentially to the
highest scene number in the tour. The tour displays each scene
for a specified dwell time before advancing to the next scene.
By default, all scenes are part of the preposition tour unless
removed.
To define and edit an individual scene:
1. Navigate to the scene that you want to define as a
preposition.
a. Click the View Control link.
b. Use the PTZ controls to move the camera into
position.
2. Click the Add scene (“+”) button to define the preposition.
3. Select a number for the scene, from 1 to 64.
4. Type an optional name for the scene, up to 20 characters
long.
5. Click OK to save the scene to the Preposition list.
The asterisk (*) to the left of the scene name indicates the
scene is part of the preposition tour.
6. To delete a scene from the list, select the scene and click
the Delete scene (“X”) button.
7. To overwrite an existing scene:
a. Click the View Control link to access the PTZ controls.
b. Use the PTZ controls to navigate to the new scene.
c. Click the scene in the Preposition list you want to
overwrite.
d. Click the Overwrite scene button to apply the new
scene to the existing preposition.
e. To change the name of the scene, double-click the
scene in the list. Then, change the name in the Edit
Scene dialog box and click OK.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
140 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
8. To view a scene in the preview window, select the scene in
the list and click the Show scene button.
9. To view a scene from the Livepage:
a. Click a scene number below the PTZ controls on the
View Control tab.
b. Use the keypad and the Show Shot button on the Aux
Control tab.
To define a preposition tour:
1. Create the individual scenes.
By default, all scenes in the Preposition list are in the
preposition tour.
2. To remove a scene from the tour, select the scene in the
list and uncheck the Include in standard tour box.
3. Select a dwell time from the Standard preposition tour
drop-down list.
4. To start the preposition tour:
a. Return to the Livepage.
b. Click the Aux Control tab.
c. Type 8in the input box and click the Aux On button.
5. To stop the tour, type 8and click the Aux Off button.
12.25 Sectors
Sector
The AutoDome Junior HD pan capability is 360° and is divided
into eight equal sectors. This section allows you to apply a title
for each sector and to designate any sectors as a Blanked
Sector.
To define a title for sectors:
1. Place the cursor in the input box to the right of the sector
number.
2. Type a title for the sector, up to 20 characters long.
3. To blank the sector, click the check box to the right of the
sector title.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 141
12.26 Miscellaneous
Address
Allows the appropriate dome to be operated via the numerical
address in the control system. Type a number between 0000
and 9999, inclusive, to identify the camera.
12.27 Logs
To save the log file information:
1. Click Download to obtain the log information.
2. Click Save.
3. Navigate to the directory in which you want to store the log
information.
4. Type a name for the log file and click Save.
12.28 Audio
You can set the gain of the audio signals to suit your specific
requirements. The current video image is shown in the small
window next to the slide controls to help you check the audio
source and improve assignments. Your changes are effective
immediately.
If you connect via Web browser, you must activate the audio
transmission on the Livepage Functions page (see
Section 11.5 The Livepage, page 95). For other connections, the
transmission depends on the audio settings of the respective
system.
Audio
The audio signals are sent in a separate data stream parallel to
the video data, and so increase the network load. The audio
data are encoded according to G.711 and require an additional
bandwidth of approx. 80 kbps for each connection. If you do
not want any audio data to be transmitted, select Off.
Line In
You can set the line input gain. Make sure that the display does
not go beyond the green zone during modulation.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
142 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
Record Format
Select a format for audio recording. The default value is G.711.
Select L16 if you want better audio quality with higher sampling
rates. This requires approx. eight times the G.711 bandwidth.
12.29 Pixel Counter
Counts the number of pixels in a defined image area. The pixel
counter allows the installer to easily verify that the camera
installation fulfills any regulatory or specific customer
requirements, for example, calculating the pixel resolution of
the face of a person passing a doorway monitored by the
camera.
12.30 Advanced Mode: Recording
12.31 Storage Management
You can record the images from the AutoDome Junior HD on
various local storage media or on an appropriately configured
iSCSI system.
For long-term, authoritative images in stationary operation, it is
essential that you use an appropriately sized iSCSI system.
It is also possible to let the VRM Video Recording Manager
control all recording when accessing an iSCSI system. This is an
external program for configuring recording tasks for video
servers. For further information please contact your local
customer service at Bosch Security Systems, Inc.
Device manager
If you activate the VRM option in this screen, the VRM Video
Recording Manager will manage all recording and you will not
be able to configure any further settings here.
CAUTION!
Activating or deactivating VRM causes the current settings to be
lost; they can only be restored through reconfiguration.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 143
Recording media
Select the required recording media here so that you can then
activate them and configure the recording parameters.
iSCSI Media
If you want to use an iSCSI system as a recording medium, you
must set up a connection to the required iSCSI system and set
the configuration parameters.
NOTICE!
The iSCSI storage system selected must be available on the
network and completely set up. Amongst other things, it must
have an IP address and be divided into logical drives (LUN).
1. Enter the IP address of the required iSCSI destination in
the iSCSI IP address field.
2. If the iSCSI destination is password protected, enter this
into the Password field.
3. Click the Read button. The connection to the IP address
will be established. In the Storage overview field, you can
see the corresponding logical drives.
Local Media
The supported local recording media are displayed in the
Storage overview field.
Activating and Configuring Storage Media
The storage overview displays the available storage media. You
can select individual media or iSCSI drives and transfer these to
the Managed storage media list. You can activate the storage
media in this list and configure them for storage.
CAUTION!
Each storage medium can only be associated with one user. If a
storage medium is already being used by another user, you can
decouple the user and connect the drive with the AutoDome
Junior HD. Before decoupling, make absolutely sure that the
previous user no longer needs the storage medium.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
144 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
1. In the Recording media section, click the iSCSI Media and
Local Media tabs to display the applicable storage media
in the overview.
2. In the Storage overview section, double-click the required
storage medium, an iSCSI LUN or one of the other
available drives. The medium is then added to the
Managed storage media list. In the Status column, newly
added media are indicated by the status Not active.
3. Click the Set button to activate all media in the Managed
storage media list. In the Status column, these are
indicated by the status Online.
4. Check the box in the Rec. 1 or Rec. 2 to specify which data
stream should be recorded on the storage media selected.
Rec. 1 stores Stream 1, Rec. 2 stores Stream 2. This
means that you can record the standard data stream on a
hard drive and record alarm images on the mobile CF card,
for example.
5. Check the boxes for the Overwrite older recordings
option to specify which older recordings can be
overwritten once the available memory capacity has been
used. Recording 1 corresponds to Stream 1, Recording 2
corresponds to Stream 2.
CAUTION!
If older recordings are not allowed to be overwritten when the
available memory capacity has been used, the recording in
question will be stopped. You can specify limitations for
overwriting old recordings by configuring the retention time
(see Section 12.33 Retention Time, page 148).
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 145
Formatting Storage Media
You can delete all recordings on a storage medium at any time.
CAUTION!
Check the recordings before deleting and back up important
sequences on the computer's hard drive.
1. Click a storage medium in the Managed storage media list
to select it.
2. Click the Edit button below the list. A new window will
open.
3. Click the Formatting button to delete all recordings in the
storage medium.
4. Click OK to close the window.
Deactivating Storage Media
You can deactivate any storage medium from the Managed
storage media list. It is then no longer used for recordings.
1. Click a storage medium in the Managed storage media list
to select it.
2. Click the Remove button below the list. The storage
medium is deactivated and removed from the list.
12.32 Recording Profiles
You can define up to ten different recording profiles. You will
then use these recording profiles in the recording scheduler,
where they are linked with the individual days and times (see
Section 12.34 Recording Schedule, page 148).
NOTICE!
You can change or add to the recording profile description on
the tabs on the Recording Scheduler page (see Page 148).
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
146 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
1. Click one of the tabs to edit the corresponding profile.
2. If necessary, click the Default button to return all settings
to their default values.
3. Click the Copy Settings button if you want to copy the
currently visible settings to other profiles. A new window
will open and you can select the profiles in which you want
to copy the settings.
4. For each profile, click the Set button to save the settings in
the unit.
Standard recording
Here you can select the mode for standard recordings.
f you select Continuous, the recording proceeds continuously. If
the maximum memory capacity is reached, older recordings will
automatically be overwritten. If you select the Pre-alarm option,
the device uses a special recording mode for optimal usage of
storage capacity: as soon as a time gap for alarm recording
begins, a recording is continuously made on one segment,
which is the size of a complete alarm sequence (pre- and post-
alarm time).
This segment functions in a similar manner to a ring buffer and
is overwritten until an alarm is actually triggered. Then,
recording occurs on the segment only for the duration of the
preset post-alarm time and a new segment is subsequently
used in the same manner.
If you select Off, no automatic recording takes place.
CAUTION!
You can specify limitations for overwriting older recordings in
Continuous mode by configuring the retention time (see
Section 12.33 Retention Time, page 148).
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 147
Standard profile
From this field, you can select the encoder profile to be used
for recording (see Section 12.17 Encoder Profile, page 124).
NOTICE!
The recording profile can deviate from the standard setting
Active profile and is only used during an active recording.
Pre-alarm Time
You can select the required pre-alarm time from the list field.
Post-alarm Time
You can select the required post-alarm time from the list field.
Post-alarm profile
You can select the encoder profile to be used for recording
during the post-alarm time (see Section 12.17 Encoder Profile,
page 124).
The Standard profile option adopts the selection at the top of
the page.
Export to FTP
Select this parameter if you want to use the Export to FTP
function on the RECORDINGS page (see Section6.8The
RECORDINGS Page, page103). Make sure to have inserted all
relevant data for FTP posting (see Section5.41Advanced Mode:
FTP Posting, page88).
Alarm input / Motion alarm / Video loss alarm
Here you can select the alarm sensor that is to trigger a
recording.
Virtual alarm
Here you can select the virtual alarm sensors that are to trigger
a recording, via RCP+ commands or alarm scripts, for example.
NOTICE!
For more information, please see the Alarm Task Script
Language document and the RCP+ documentation. These
documents can be found on the product CD supplied.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
148 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
Recording includes
You can specify whether, in addition to video data and
metadata (for example alarms, VCA data and serial data) should
also be recorded. Including metadata could make subsequent
searches of recordings easier but it requires additional memory
capacity.
CAUTION!
Without metadata, it is not possible to include video content
analysis in recordings.
12.33 Retention Time
You can specify the retention times for recordings. If the
available memory capacity of a medium has been used, older
recordings are only overwritten if the retention time entered
here has expired.
NOTICE!
Make sure that the retention time corresponds with the
available memory capacity. A rule of thumb for the memory
requirement is as follows: 1 GB per hour retention time with
4CIF for complete frame rate and high image quality.
Retention time
Enter the required retention time in hours or days for each
recording. Recording 1 corresponds to Stream 1, Recording 2
corresponds to Stream 2.
12.34 Recording Schedule
The recording scheduler allows you to link the created
recording profiles with the days and times at which the
camera's images are to be recorded in the event of an alarm.
You can link any number of 15-minute intervals with the
recording profiles for each day of the week. Moving the mouse
cursor over the table displays the time below it. This aids
orientation.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 149
In addition to the normal weekdays, you can define holidays
that are not in the standard weekly schedule on which
recordings are to apply. This allows you to apply a schedule for
Sundays to other days with dates that fall on varying weekdays.
1. Click the profile you want to link in the Time periods field.
2. Click in a field in the table, hold down the mouse button
and drag the cursor over all the periods to be assigned to
the selected profile.
3. Use the right mouse button to deselect any of the intervals.
4. Click the Select All button to link all time intervals to the
selected profile.
5. Click the Clear All button to deselect all of the intervals.
6. When you are finished, click the Set button to save the
settings in the unit.
Holidays
You can define holidays that are not in the standard weekly
schedule on which recordings are to apply. This allows you to
apply a schedule for Sundays to other days with dates that fall
on varying weekdays.
1. Click the Holidays tab. Any days that have already been
selected will be shown in the table.
2. Click the Add button. A new window will open.
3. Select the desired date from the calendar. You can select
several consecutive calendar days by holding down the
mouse button. These will later be displayed as a single
entry in the table.
4. Click OK to accept the selection. The window will close.
5. Assign the individual holidays to the recording profiles, as
described above.
Deleting Holidays
You can delete holidays you have defined yourself at any time.
1. Click the Delete button. A new window will open.
2. Click the date you wish to delete.
3. Click OK. The item will be deleted from the table and the
window will close.
4. The process must be repeated for deleting additional days.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
150 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
Time periods
You can change the names of the recording profiles.
1. Click a profile and then the Rename button.
2. Enter your chosen name and then click the Rename button
again.
Activating the Recording
After completing configuration you must activate the recording
scheduler and start the recording. The configuration can be
modified at any time.
You can stop the recording activity at any time and modify the
settings.
1. Click the Start button to activate the recording scheduler.
2. Click the Stop button to deactivate the recording
scheduler. Running recordings are interrupted.
Recording status
The graphic indicates the recording activity of the AutoDome
Junior HD. You will see an animated graphic while recording is
taking place.
12.35 Recording Status
Certain details on the recording status are displayed here for
information purposes. You cannot change any of these settings.
12.36 Advanced Mode: Alarm
12.37 Alarm Connections
You can select how the AutoDome Junior HD responds to an
alarm. In the event of an alarm, the unit can automatically
connect to a pre-defined IP address. You can enter up to ten IP
addresses to which the AutoDome Junior HD will connect in
sequence in the event of an alarm, until a connection is made.
Connect on alarm
Select On so that the AutoDome Junior HD automatically
connects to a predefined IP address in the event of an alarm.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 151
By setting Follows input 1 the unit maintains the connection
that has been automatically established for as long as an alarm
exists on alarm input 1.
NOTICE!
In the default setting, Stream 2 is transmitted for alarm
connections. Bear this fact in mind when assigning the profile
(see Section 12.17 Encoder Profile, page 124).
Number of destination IP address
Specify the numbers of the IP addresses to be contacted in the
event of an alarm. The unit contacts the remote stations one
after the other in the numbered sequence until a connection is
made.
Destination IP address
For each number, enter the corresponding IP address for the
desired remote station.
Destination password
If the remote station is password protected, enter the
password here.
In this page, you can save a maximum of ten destination IP
addresses and hence up to ten passwords for connecting to
remote stations. If connections to more than ten remote
stations are to be possible, for example when initiating
connections via higher-ranking systems such as VIDOS or Bosch
Video Management System, you can store a general password
here. The AutoDome Junior HD can use this general password
to connect to all remote stations protected with the same
password. In this case, proceed as follows:
1. Select 10 from the Number of destination IP address list
field.
2. Enter the address 0.0.0.0 in the Destination IP address
field.
3. Enter your chosen password in the Destination password
field.
4. Define this password as the user password for all remote
stations to which a connection is to be possible.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
152 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
NOTICE!
If you enter the destination IP address 0.0.0.0 for destination
10, this address will no longer be used for the tenth attempt at
automatic connection in the event of an alarm. The parameter is
then used only to save the general password.
Video transmission
If the unit is operated behind a firewall, TCP (HTTP port)
should be selected as the transfer protocol. For use in a local
network, select UDP.
CAUTION!
Please note that in some circumstances, a larger bandwidth
must be available on the network for additional video images in
the event of an alarm, in case Multicast operation is not
possible. To enable Multicast operation, select the UDP option
for the Video transmission parameter here and on the Network
page (see Page 165).
Stream
Select the stream for transmission in case of an alarm.
Remote port
Depending on the network configuration, select a browser port
here. The ports for HTTPS connections will be available only if
the On option is selected in the SSL encryption parameter.
Video output
If you know which unit is being used as the receiver, you can
select the analog video output to which the signal should be
switched. If the destination unit is unknown, it is advisable to
select the First available option. In this case, the image is
placed on the first free video output. This is an output on which
there is no signal. The connected monitor only displays images
when an alarm is triggered. If you select a particular video
output and a split image is set for this output on the receiver,
you can also select from Decoder the decoder in the receiver
that is to be used to display the alarm image.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 153
NOTICE!
Refer to the destination unit documentation concerning image
display options and available video outputs.
Decoder
Select a decoder of the receiver to display the alarm image. The
decoder selected has an impact on the position of the image in
a split screen. For example, you can specify via a VIP XD that
the upper-right quadrant should be used to display the alarm
image by selecting decoder 2.
SSL encryption
The data for the connection, for example the password, can be
securely transmitted with SSL encryption. If you have selected
the On option, only encrypted ports are offered in the Remote
port parameter.
NOTICE!
Please note that the SSL encryption must be activated and
configured at both ends of a connection. This requires the
appropriate certificates to be uploaded onto the AutoDome
Junior HD.
You can activate and configure encryption of the media data
(video and metadata) on the Encryption page (see
Section 12.47 Advanced, Page 170).
Auto-connect
Select the On option to automatically re-establish a connection
to one of the previously specified IP addresses after each
reboot, after a connection breakdown or after a network failure.
NOTICE!
In the default setting, Stream 2 is transmitted for automatic
connections. Bear this fact in mind when assigning the profile
(see Section 12.17 Encoder Profile, page 124).
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
154 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
12.38 VCA
The AutoDome Junior HD contains an integrated video content
analysis (VCA), which can detect and analyze changes in the
signal on the basis of image processing. Such changes can be
due to movements in the camera's field of view.
You can select various VCA configurations and adapt these to
your application as required. The Silent MOTION+ configuration
is active by default. In this configuration, metadata is created to
facilitate searches of recordings; however, no alarm is
triggered.
1. Select a VCA configuration and make the required settings.
2. If necessary, click the Default button to return all settings
to their default values.
VCA Profiles
You can configure two profiles with different VCA
configurations. You can save profiles on your computer's hard
drive and load saved profiles from there. This can be useful if
you want to test a number of different configurations. Save a
functioning configuration and test new settings. You can use
the saved configuration to restore the original settings at any
time.
1. Select a VCA profile and enter the required settings.
2. If necessary, click the Default button to return all settings
to their default values.
3. Click the Save... button to save the profile settings to
another file. A new window is opened, in which you can
specify where you want to save the file and what name you
want to save it under.
4. Click the Load... button to load a saved profile. A new
window opens in which you can select the profile file and
specify where to save the file.
VCA configuration
Select one of the profiles here to activate it or edit it.
You can rename the profile.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 155
CAUTION!
Do not use any special characters, for example &, in the name.
Special characters are not supported by the system's internal
recording management and may therefore result in the Player or
Archive Player being unable to play back the recording.
1. To rename the file, click the icon to the right of the list field
and enter the new profile name in the field.
2. Click the icon again. The new profile name is saved.
Alarm status
The alarm status is displayed here for information purposes.
This means you can check the effects of your settings
immediately.
Analysis type
Select the required analysis algorithm. By default, only
MOTION+ is available – this offers a motion detector and
essential recognition of tampering.
NOTICE!
Additional analysis algorithms with comprehensive functions
such as IVMD and IVA are available from Bosch Security
Systems, inc.
If you select one of these algorithms, you can set the
corresponding parameters here directly. You can find
information on this in the relevant documents on the product
CD supplied.
Metadata is always created for a video content analysis, unless
this was explicitly excluded. Depending on the analysis type
selected and the relevant configuration, additional information
overlays the video image in the preview window next to the
parameter settings. With the MOTION+ analysis type, for
example, the sensor fields in which motion is recorded will be
marked with rectangles.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
156 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
NOTICE!
On the Livepage Functions page, you can also enable
additional information overlays for the Livepage (see
Section 12.14 Livepage Functions, page 121).
Motion detector (MOTION+ only)
For the detector to function, the following conditions must be
met:
–
–
–
Analysis must be activated.
At least one sensor field must be activated.
The individual parameters must be configured to suit the
operating environment and the desired responses.
The sensitivity must be set to a value greater than zero.
–
CAUTION!
Reflections of light (off glass surfaces, etc.), switching lights on
or off or changes in the light level caused by cloud movement
on a sunny day can trigger unintended responses from the
motion detector and generate false alarms. Run a series of tests
at different times of the day and night to ensure that the video
sensor is operating as intended.
For indoor surveillance, ensure constant lighting of the areas
during the day and at night.
Sensitivity (MOTION+ only)
The basic sensitivity of the motion detector can be adjusted for
the environmental conditions to which the camera is subject.
The sensor reacts to variations in the brightness of the video
image. The darker the observation area, the higher the value
that must be selected.
Minimum object size (MOTION+ only)
You can specify the number of sensor fields that a moving
object must cover to generate an alarm. This is to prevent
objects that are too small from triggering an alarm.
A minimum value of 4 is recommended. This value corresponds
to four sensor fields.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 157
Select Area (MOTION+ only)
The areas of the image to be monitored by the motion detector
can be selected. The video image is subdivided into 858 square
fields. Each of these fields can be activated or deactivated
individually. If you wish to exclude particular regions of the
camera's field of view from monitoring due to continuous
movement (by a tree in the wind, etc.), the relevant fields can
be deactivated.
1. Click Select Area to configure the sensor fields. A new
window will open.
2. If necessary, click Clear All first to clear the current
selection (fields marked yellow).
3. Left-click the fields to be activated. Activated fields are
marked yellow.
4. If necessary, click Select All to select the entire video
frame for monitoring.
5. Right-click any fields you wish to deactivate.
6. Click OK to save the configuration.
7. Click the close button X in the window title bar to close
the window without saving the changes.
Tamper detection
You can reveal the tampering of cameras and video cables by
means of various options. Run a series of tests at different
times of the day and night to ensure that the video sensor is
operating as intended.
NOTICE!
The options for tamper detection can only be set for fixed
cameras. Dome cameras or other motorized cameras cannot be
protected in this manner as the movement of the camera itself
causes changes in the video image that are too great.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
158 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
Sensitivity
NOTICE!
This and the following parameter are only accessible if the
reference check is activated.
The basic sensitivity of the tamper detection can be adjusted
for the environmental conditions to which the camera is
subject.
The algorithm reacts to the differences between the reference
image and the current video image. The darker the observation
area, the higher the value that must be selected.
Trigger delay (s)
You can set delayed alarm triggering. The alarm is only triggered
after a set time interval in seconds has elapsed and then only if
the triggering condition still exists. If the original condition has
been restored before this time interval elapses, the alarm is not
triggered. This allows you to avoid false alarms triggered by
short-term changes, for example cleaning activities in the direct
field of vision of the camera.
Global change
You can set how large the global change in the video image
must be for an alarm to be triggered. This setting is
independent of the sensor fields selected under Select Area.
Set a high value if fewer sensor fields need to change to trigger
an alarm. With a low value, it is necessary for changes to occur
simultaneously in a large number of sensor fields to trigger an
alarm.
This option allows you to detect, independently of motion
alarms, manipulation of the orientation or location of a camera
resulting from turning the camera mount bracket, for instance.
Global change
Activate this function if the global change, as set with the
Global change slide control, should trigger an alarm.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 159
Scene too bright
Activate this function if tampering associated with exposure to
extreme light (for instance, shining a flashlight directly on the
lens) should trigger an alarm. The average brightness of the
scene provides a basis for recognition.
Scene too dark
Activate this function if tampering associated with covering the
lens (for instance, by spraying paint on it) should trigger an
alarm. The average brightness of the scene provides a basis for
recognition.
Scene too noisy
Activate this function if tampering associated with EMC
interference (noisy scene as the result of a strong interference
signal in the vicinity of the video lines), as an example, should
trigger an alarm.
Select Area
You can select the image areas in the reference image that are
to be monitored. The video image is subdivided into 858 square
fields. Each of these fields can be activated or deactivated
individually.
NOTICE!
Select only those areas for reference monitoring in which no
movement takes place and that are always evenly lit, as false
alarms could otherwise be triggered.
1. Click Select Area to configure the sensor fields. A new
window will open.
2. If necessary, click Clear All first to clear the current
selection (fields marked yellow).
3. Left-click the fields to be activated. Activated fields are
marked yellow.
4. If necessary, click Select All to select the entire video
frame for monitoring.
5. Right-click any fields you wish to deactivate.
6. Click OK to save the configuration.
7. Click the close button X in the window title bar to close
the window without saving the changes.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
160 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
12.39 Alarm E-Mail
As an alternative to automatic connecting, alarm states can also
be documented by e-mail. In this way it is possible to notify a
recipient who does not have a video receiver. In this case, the
AutoDome Junior HD automatically sends an e-mail to a
previously defined e-mail address.
Send alarm e-mail
Select On if you want the unit to automatically send an alarm e-
mail in the event of an alarm.
Mail server IP address
Enter the IP address of a mail server that operates on the SMTP
standard (Simple Mail Transfer Protocol). Outgoing e-mails are
sent to the mail server via the address you entered. Otherwise
leave the box blank (0.0.0.0).
SMTP user name
Enter a registered user name for the chosen mailserver here.
SMTP password
Enter the required password for the registered user name here.
Format
You can select the data format of the alarm message.
–
–
Standard (with JPEG)
E-mail with attached JPEG image file.
SMS
E-mail in SMS format to an e-mail-to-SMS gateway (for
example to send an alarm by cellphone) without an image
attachment.
CAUTION!
When a cellphone is used as the receiver, make sure to activate
the e-mail or SMS function, depending on the format, so that
these messages can be received.
You can obtain information on operating your cellphone from
your cellphone provider.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 161
Attach JPEG from camera
Click the checkbox to specify that JPEG images are sent from
the camera. An enabled video input is indicated by a check
mark.
Destination address
Enter the e-mail address for alarm e-mails here. The maximum
address length is 49 characters.
Sender name
Enter a unique name for the e-mail sender, for example the
location of the unit. This will make it easier to identify the origin
of the e-mail.
Test e-mail
You can test the e-mail function by clicking the Send Now
button. An alarm e-mail is immediately created and sent.
12.40 Alarm Task Editor
CAUTION!
Editing scripts on this page overwrites all settings and entries
on the other alarm pages. This procedure cannot be reversed.
In order to edit this page, you must have programming
knowledge and be familiar with the information in the Alarm
Task Script Language document.
As an alternative to the alarm settings on the various alarm
pages, you can enter your desired alarm functions in script form
here. This will overwrite all settings and entries on the other
alarm pages.
1. Click the Examples link under the Alarm Task Editor field
to see some script examples. A new window will open.
2. Enter new scripts in the Alarm Task Editor field or change
existing scripts in line with your requirements.
3. When you are finished, click the Set button to transmit the
scripts to the unit. If the transfer was successful, the
message Script successfully parsed is displayed over the
text field. If it was not successful, an error message will be
displayed with further information.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
162 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
12.41 Alarm Rules
The AutoDome Junior HD features an alarm rule engine. In its
simplest form, an alarm rule can define which input(s) activate
which output(s). Basically, an alarm rule allows you to
customize an AutoDome Junior HD to automatically respond to
different alarm inputs.
To configure an alarm rule specify one input from either a
physical connection, a motion detection trigger, or from a
connection to the camera’s Livepage. The physical input
connection can be activated by dry contact devices such as
pressure pads, door contacts and similar devices.
Next, specify up to two (2) rule outputs, or the camera’s
response to the input. Outputs include a physical alarm relay,
an AUX command, or a preposition scene.
1. Click the Enabled check box to activate the alarm.
2. Choose one of the following alarm inputs:
–
–
–
Local Input 1: a physical alarm connection.
Local Input 2: a physical alarm connection.
IVA/MOTION+: an alarm when IVA or motion detection
is activated.
–
Connection: an alarm when an attempt is made to
access the camera’s IP address.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 163
3. Choose one of the following output commands for both
Output 1 and Output 2 settings:
–
–
None: no defined command.
Aux On: defines a standard or custom keyboard ON
command.
Refer to Section 13 Keyboard Commands by Number,
page 179, for a list of valid commands.
Note: Only commands 1, 2, 8, 18, 20, 43, 60, 80, 86
are supported. Support for the remaining commands
is scheduled for a future release.
–
–
Aux Off: defines a standard or custom keyboard OFF
command.
Refer to Section 13 Keyboard Commands by Number,
page 179, for a list of valid commands.
Note: Only commands 1, 2, 8, 18, 20, 43, 60, 80, 86
are supported. Support for the remaining commands
is scheduled for a future release.
Shot: defines a preset scene from shot 1-64.
4. Click Set to save and to activate the alarm rules.
12.42 Advanced Mode: Interfaces
12.43 Alarm Inputs
Select the type of input for each physical alarm. Select from
either N.O. (Normally Open) or N.C. (Normally Closed) and
provide an optional name for each input.
Alarm Input
Select N.O. if the alarm is to be triggered when the contact
closes. Select N.C. if the alarm is to be triggered when the
contact opens.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
164 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
Name
You can enter a name for each alarm input, which is then
displayed below the icon for the alarm input on the Livepage if
configured correctly (see Section 12.14 Livepage Functions,
page 121). Furthermore, in the Forensic Search program, you
can use the name as a filter option for quick search through the
recordings.
CAUTION!
Do not use any special characters, for example &, in the name.
Special characters are not supported by the system's internal
recording management and may therefore result in the Player or
Archive Player programs being unable to play back the
recording.
12.44 Relay
You can configure the switching behavior of the relay outputs.
For each relay, you can specify an open switch relay (normally
closed contact) or a closed switch relay (normally open
contact).
You can also specify whether an output should operate as a
bistable or monostable relay. In bistable mode, the triggered
state of the relay is maintained. In monostable mode, you can
set the time after which the relay will return to the idle state.
You can select different events that automatically activate an
output. It is possible, for example, to turn on a floodlight by
triggering a motion alarm and then turning the light off again
when the alarm has stopped.
Idle State
Select Open if you want the relay to operate as an NO contact,
or select Closed if the relay is to operate as an NC contact.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 165
Operations Mode
Select an operating mode for the relay.
For example, if you want an alarm-activated lamp to stay on
after the alarm ends, select Bistable. If you wish an alarm-
activated siren to sound for ten seconds, for example, select
10s.
Relay Name
You can assign a name for the relay here. The name is shown on
the button next to Trigger relay. The Livepage can also be
configured to display the name under the relay icon.
Furthermore, in the Forensic Search program, you can use the
name as a filter option for quick search through the recordings.
CAUTION!
Do not use any special characters, for example &, in the name.
Special characters are not supported by the system's internal
recording management and may therefore result in the Player or
Archive Player programs being unable to play back the
recording.
Trigger Relay
Click the button to trigger the relay manually (for testing or to
operate a door opener, for example).
12.45 Advanced Mode: Network
12.46 Network Access
The settings on this page are used to integrate the AutoDome
800 Series into an existing network.
Some changes only take effect after the unit is rebooted. In this
case, the Set button changes to Set and Reboot.
1. Make the desired changes.
2. Click the Set and Reboot button. The AutoDome 800
Series is rebooted and the changed settings are activated.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
166 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
CAUTION!
If you change the IP address, subnet mask or gateway address,
the AutoDome 800 Series is only available under the new
addresses after the reboot.
Automatic IP assignment
If a DHCP server is employed in the network for the dynamic
assignment of IP addresses, you can activate acceptance of IP
addresses automatically assigned to the AutoDome 800 Series.
Certain applications (VIDOS, Bosch Video Management System,
Archive Player, Configuration Manager) use the IP address for
the unique assignment of the unit. If you use these applications,
the DHCP server must support the fixed assignment between IP
address and MAC address, and must be appropriately set up so
that, once an IP address is assigned, it is retained each time the
system is rebooted.
12.46.1 IPv4
IP address
Enter the desired IP address for the AutoDome 800 Series in
this field. The IP address must be valid for the network.
Subnet mask
Enter the appropriate subnet mask for the selected IP address
here.
Gateway address
If you want the unit to establish a connection to a remote
location in a different subnet, enter the IP address of the
gateway here. Otherwise leave the box blank (0.0.0.0).
12.46.2 IPv6
Consult with the network administrator before making changes
to the this section.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 167
IP Address
Enter the desired IP address for the AutoDome 800 Series in
this field. The IP address must be valid for the network. A
typical IPv6 address may resemble the following example:
2001:db8 : : 52:1:1
Consult the network administrator for valid IPv6 address
construction.
Prefix Length
A typical IPv6 node address consists of a prefix and an interface
identifier (total 128 bits). The prefix is the part of the address
where the bits have fixed values or are the bits that define a
subnet.
Gateway Address
If you want the unit to establish a connection to a remote
location in a different subnet, enter the IP address of the
gateway here. Otherwise leave the box blank (0.0.0.0).
12.46.3 Detailed Settings
DNS server address
The AutoDome 800 Series is easier to access if the unit is listed
on a DNS server. If you wish, for example, to establish an
Internet connection to the AutoDome 800 Series, it is sufficient
to enter the name given to the unit on the DNS server as a URL
in the browser. Enter the IP address of the DNS server here.
Servers are supported for secure and dynamic DNS.
Video Transmission
If the unit is operated behind a firewall, TCP (HTTP port)
should be selected as the transfer protocol. For use in a local
network, select UDP.
CAUTION!
Multicast operation is only possible with the UDP protocol. The
TCP protocol does not support multicast connections.
The MTU value in UDP mode is 1,514 bytes.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
168 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
HTTP browser port
Select a different HTTP browser port from the list if required.
The default HTTP port is 80. If you want to allow only secure
connections via HTTPS, you must deactivate the HTTP port. In
this case, select Off.
HTTPS browser port
If you wish to allow browser access on the network via a secure
connection, select an HTTPS browser port from the list if
necessary. The default HTTPS port is 443. Select the Off option
to deactivate HTTPS ports; only unsecured connections will
now be possible.
The AutoDome 800 Series uses the TLS 1.0 encryption
protocol. You may have to activate this protocol via your
browser configuration. You must also activate the protocol for
the Java applications (via the Java control panel in the
Windows control panel).
NOTICE!
If you want to allow only secure connections with SSL
encryption, you must select the Off option for each of the
parameters HTTP browser port, RCP+ port 1756 and Telnet
support. This deactivates all unsecured connections.
Connections will then only be possible via the HTTPS port.
You can activate and configure encryption of the media data
(video and metadata) on the Encryption page (see
Section 12.47 Advanced, Page 170).
RCP+ port 1756
To exchange connection data, you can activate the unsecured
RCP+ port 1756. If you want connection data to be transmitted
only when encrypted, select the Off option to deactivate the
port.
Telnet support
If you want to allow only secure connections with encrypted
data transmission, you must select the Off option to deactivate
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 169
Telnet support. The unit will then no longer be accessible using
the Telnet protocol.
Interface mode ETH
If necessary, select the Ethernet link type for the ETH interface.
Depending on the unit connected, it may be necessary to select
a special operation type.
Network MSS (Byte)
You can set the maximum segment size for the IP packet's user
data. This gives you the option to adjust the size of the data
packets to the network environment and to optimize data
transmission. Please comply with the MTU value of 1,514 bytes
in UDP mode.
iSCSI MSS (Byte)
You can specify a higher MSS value for a connection to the
iSCSI system than for the other data traffic via the network. The
potential value depends on the network structure. A higher
value is only useful if the iSCSI system is located in the same
subnet as the AutoDome 800 Series.
Enable DynDNS
DynDNS.org is a DNS hosting service that stores IP addresses in
a database ready for use. It allows you to select the AutoDome
800 Series via the Internet using a host name, without having to
know the current IP address of the unit. You can enable this
service here. To do this, you must have an account with
DynDNS.org and you must have registered the required host
name for the unit on that site.
NOTICE!
Information about the service, registration process and
available host names can be found at DynDNS.org.
Host name
Enter the host name registered on DynDNS.org for the
AutoDome 800 Series here.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
170 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
User name
Enter the user name you registered at DynDNS.org here.
Password
Enter the password you registered at DynDNS.org here.
Force registration now
You can force the registration by transferring the IP address to
the DynDNS server. Entries that change frequently are not
provided in the Domain Name System. It is a good idea to force
the registration when you are setting up the device for the first
time. Only use this function when necessary and no more than
once a day, to avoid the possibility of being blocked by the
service provider. To transfer the IP address of the AutoDome
800 Series, click the Register button.
Status
The status of the DynDNS function is displayed here for
information purposes. You cannot change any of these settings.
12.47 Advanced
The settings on this page are used to implement advanced
settings for the network.
Some changes only take effect after the unit is rebooted. In this
case, the Set button changes to Set and Reboot.
1. Make the desired changes.
2. Click the Set and Reboot button. The AutoDome Junior HD
is rebooted and the changed settings are activated.
SNMP
The AutoDome Junior HD supports the SNMP V2 (Simple
Network Management Protocol) for managing and monitoring
network components, and can send SNMP messages (traps) to
IP addresses. The unit supports SNMP MIB II in the unified
code. If you wish to send SNMP traps, enter the IP addresses of
one or two required target devices here.
If you select On for the SNMP parameter and do not enter an
SNMP host address, the AutoDome Junior HD does not send
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 171
them automatically, but only replies to SNMP requests. If you
enter one or two SNMP host addresses, SNMP traps are sent
automatically. Select Off to deactivate the SNMP function.
1. SNMP host address / 2. SNMP host address
If you wish to send SNMP traps automatically, enter the IP
addresses of one or two required target units here.
SNMP traps
You can select which traps are to be sent.
1. Click Select. A list is opened.
2. Click the checkboxes to select the required traps. All the
checked traps will be sent.
3. Click Set to accept the selection.
Authentication
If a RADIUS server is employed in the network for managing
access rights, authentication must be activated here to allow
communication with the unit. The RADIUS server must also
contain the corresponding data.
To configure the unit, you must connect the AutoDome Junior
HD directly to a computer using a network cable. This is
because communication via the network is not enabled until the
Identity and Password parameters have been set and
successfully authenticated.
Identity
Enter the name that the RADIUS server is to use for identifying
the AutoDome Junior HD.
Password
Enter the password that is stored in the RADIUS server.
RTSP port
If necessary, select a different port for the exchange of the
RTSP data from the list. The standard RTSP port is 554. Select
Off to deactivate the RTSP function.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
172 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
UPnP
You can activate the universal plug and play function (UPnP).
When activated the camera reacts on requests from the
network and will be registered automatically as a new network
device on the inquiring computers. The access to the camera is
then possible via the Windows file explorer, and without
knowledge of the camera’s IP address.
NOTICE!
In order to use the UPnP function on a computer with Windows
XP or Windows Vista, the Universal Plug and Play Device Host
and the SSDP Discovery services must be activated.
This function should not be used in large installations due to
the large number of registration notifications.
TCP Metadata Input
The device can receive data from an external TCP sender, for
example an ATM or POS device, and store it as metadata.
Select the port for TCP communication. Select Off to deactivate
the TCP metadata function.
Sender IP Address
Enter the IP address of the TCP metadata sender here.
NTCIP
Specifies a set of rules and protocols for organizing, describing
and exchanging transportation management information
between transportation management applications and
transportation equipment such that they interoperate with each
other.
Select a port for NTCIP and the Address from the appropriate
drop-down lists.
12.48 Multicast
In addition to a 1:1 connection between an encoder and a
single receiver (unicast), the AutoDome Junior HD can enable
multiple receivers to receive the video signal from an encoder
simultaneously. The device either duplicates the data stream
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 173
itself and then distributes it to multiple receivers (Multi-
unicast) or it sends a single data stream to the network, where
the data stream is simultaneously distributed to multiple
receivers in a defined group (Multicast). You can enter a
dedicated multicast address and port for each stream. You can
switch between the streams by clicking the appropriate tabs.
NOTICE!
Multicast operation requires a multicast-enabled network that
uses the UDP and the Internet Group Management IGMP
protocols. Other group management protocols are not
supported. The TCP protocol does not support multicast
connections.
A special IP address (class D address) must be configured for
multicast operation in a multicast-enabled network.
The network must support group IP addresses and the Internet
Group Management Protocol (IGMP V2). The address range is
from 225.0.0.0 to 239.255.255.255.
The multicast address can be the same for multiple streams.
However, it will be necessary to use a different port in each
case so that multiple data streams are not sent simultaneously
using the same port and multicast address.
NOTICE!
The settings must be made individually for each stream.
Enable
To enable simultaneous data reception on several receivers you
need to activate the multicast function. To do this, check the
box. You can then enter the multicast address.
Multicast Address
Enter a valid multicast address for each stream to be operated
in multicast mode (duplication of the data streams in the
network).
With the setting 0.0.0.0 the encoder for the relevant stream
operates in multi-unicast mode (copying of data streams in the
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
174 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
unit). The AutoDome Junior HD supports multi-unicast
connections for up to five simultaneously connected receivers.
NOTICE!
Duplication of data places a heavy demand on the unit and can
lead to impairment of the image quality under certain
circumstances.
Port
Assign a different port to each data stream if there are
simultaneous data streams at the same multicast address.
Enter the port address of the required stream here.
Streaming
Click the checkbox to activate multicast streaming mode for the
relevant stream. An enabled stream is indicated by a check
mark. The device even streams multicast data if no connection
is active.
Multicast packet TTL
You can enter a value to specify how long the multicast data
packets are active on the network. This value must be greater
than one if multicast is to be run via a router.
12.49 FTP Posting
You can save individual JPEG images on an FTP server at
specific intervals. You can then retrieve these images at a later
date to reconstruct alarm events if required.
File name
You can select how file names will be created for the individual
images that are transmitted.
–
–
Overwrite
The same file name is always used and any existing file will
be overwritten with the current file.
Increment
A number from 000 to 255 is added to the file name and
automatically incremented by 1. When it reaches 255 it
starts again from 000.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
–
Configuring the AutoDome Junior HD | en 175
Date/time suffix
The date and time are automatically added to the file
name. When setting this parameter, ensure that the unit's
date and time are always correctly set. Example: the file
snap011005_114530.jpg was stored on October 1, 2005 at
11:45 and 30 seconds.
Posting interval
Enter the interval in seconds at which the images will be sent to
an FTP server. Enter zero if you do not want any images to be
sent.
FTP server IP address
Enter the IP address of the FTP server on which you wish to
save the JPEG images.
FTP server login
Enter your login name for the FTP server.
FTP server password
Enter the password that gives you access to the FTP server.
Path on FTP server
Enter the exact path on which you wish to post the images on
the FTP server.
Max. Bit Rate
You can limit the bit rate for FTP posting.
12.50 IPv4 Filter
Use this setting to configure a filter that allows or blocks
network traffic that matches a specified address or protocol.
IP Address 1 / 2
Enter the IPv4 address that you want to allow or block
Mask 1 / 2
Enter the subnet mask for the appropriate IPv4 address.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
176 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
12.51 Advanced Mode: Service
12.52 Maintenance
Firmware
The AutoDome Junior HD is designed in such a way that its
functions and parameters can be updated with firmware. To do
this, transfer the current firmware package to the unit via the
selected network. It will then be automatically installed there.
In this way, an AutoDome Junior HD can be serviced and
updated remotely without a technician having to change the
installation on site.
Refer to Section 16 BVIP Firmware Updates, page 185, for
firmware upgrade instructions.
CAUTION!
Before launching the firmware upload make sure that you have
selected the correct upload file. Uploading the wrong files can
result in the unit no longer being addressable, in which case
you must replace the unit.
You should never interrupt the installation of firmware. An
interruption can lead to the flash-EPROM being incorrectly
programmed. This in turn can result in the unit no longer being
addressable, in which case it will have to be replaced. Even
changing to another page or closing the browser window leads
to an interruption.
Refer to Section 16 BVIP Firmware Updates, page 185, for
firmware upgrade instructions.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Configuring the AutoDome Junior HD | en 177
Configuration
You can save configuration data for the AutoDome Junior HD on
a computer and then load saved configuration data from a
computer to the unit.
Upload
1. Enter the full path of the file to upload or click Browse to
select the required file.
2. Make certain that the file to be loaded comes from the
same unit type as the unit you want to configure.
3. Next, click Upload to begin transferring the file to the unit.
The progress bar allows you to monitor the transfer.
Once the upload is complete, the new configuration is
activated. The time remaining is shown by the message going to
reset Reconnecting in ... seconds. The unit reboots
automatically once the upload has successfully completed.
Download
1. Click the Download button. A dialog box opens.
2. Follow the on-screen instructions to save the current
settings.
SSL certificate
To be able to work with an SSL encrypted data connection,
both ends of a connection must hold the relevant certificates.
You can upload the SSL certificate, comprising one or multiple
files, onto the AutoDome Junior HD.
If you wish to upload multiple files onto the AutoDome Junior
HD, you must select them consecutively.
1. Enter the full path of the file to upload or click Browse to
select the required file.
2. Next, click Upload to begin transferring the file to the unit.
3. Once all files have been successfully uploaded, the unit
must be rebooted. In the address bar of your browser,
enter /reset after the IP address of the AutoDome Junior
HD (for example 192.168.0.10/reset).
The new SSL certificate is valid.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
178 en | Configuring the AutoDome Junior HD
AutoDome Junior HD
Maintenance log
You can download an internal maintenance log from the unit to
send it to Customer Service for support purposes. To do so,
you have to make sure that HTTPS browser port is not set to
Off and TLS 1.0 support is activated for your browser. Click
Download and select a storage location for the file.
12.53 Licenses
You can enter the activation key to release additional functions
or software modules.
NOTICE!
The activation key cannot be deactivated again and is not
transferable to other units.
12.54 System Overview
The data on this page are for information purposes only and
cannot be changed. Keep a record of this information in case
technical assistance is required.
NOTICE!
You can select all required text on this page with the mouse and
copy it to the clipboard with the [Ctrl]+[C] key combination, for
example if you want to send it via e-mail.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Keyboard Commands by Number | en 179
13
Keyboard Commands by Number
AlarmRule Function Comm Command
Description
Output
Key
No.
1
Y
Y
Y
On/Off
On/Off
On/Off
Scan 360°
Autopan
Autopan without limits
Autopan between limits
2
8
Play Pre-
Activate/Deactivate
standard tour
position Tour
Y
Y
On/Off 18
On/Off 20
On/Off 40
On/Off 43
AutoPivot
Enable
Enables/disables AutoPivot
Backlight Comp Toggles Backlight
Compensation
Restore Camera Restores all setting to their
Settings
original defaults
Toggles AGC
Y
Auto Gain
Control
Y
Y
Y
On/Off 50
On/Off 52
On/Off 60
Playback Tour A Activate/Deactivate
Playback Tour B Activate/Deactivate
On Screen
Display
On–enable
Off–disable
Y
Y
On/Off 80
On/Off 86
On/Off 100
On/Off 101
Digital Zoom
Lock
Turns digital zoom on and
off
Sector Blanking Enables/Disables Sector
Blanking
Record Tour A
On– start recording
Off – stop recording
Record Tour B
On– start recording
Off – stop recording
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
180 en | Keyboard Commands by Number
AutoDome Junior HD
AlarmRule Function Comm Command
Description
Output
Key
No.
On/Off 601
Vivid Color
Flickerless
Toggles the vivid color
option on or off.
On/Off 602
Toggles the flickerless mode
on or off. This mode
reduces the flicker of video
when the camera is installed
into a different frequency.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Preventive Maintenance | en 181
14
Preventive Maintenance
The following preventive maintenance schedule allows
detection and correction of minor faults before they become
serious and cause equipment failure. Periodically perform the
following:
–
Inspect all connecting cables for deterioration or other
damage.
–
–
Wipe housing with a clean damp cloth.
Clean the dome/windows with an approved P.C (LEXAN)
Cleaner (Novus LEXAN cleaner-plastic polish).
Verify that all the mounting hardware is secure.
–
When cleaning the dome bubble heed these warning:
–
Do not use alcohol-based solutions to clean the bubble.
This will cause the bubble to cloud and over time cause
stress aging, which makes the bubble brittle.
Do not use abrasive or highly alkaline cleaners on the
bubble.
–
–
–
–
Do not scrape the bubble with razor blades or other sharp
instruments.
Do not use Benzene, Gasoline, Acetone, or Carbon
Tetrachloride on the bubble.
Do not clean bubbles in direct sunlight or on very hot days.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
182 en | Troubleshooting
AutoDome Junior HD
15
Troubleshooting
If you experience difficulties operating your AutoDome Junior
camera, refer to the following. If the guidelines do not enable
you to solve the problem, contact an authorized technician.
Problem
Check
Need to remove trim
ring.
Use a slotted screw driver and push the clips
outward while gently pulling down on the edge of
the trim ring.
Nothing appears on
the screen.
Are the power cord and line connection between
the camera and monitor made properly?
The image on the
screen is dim.
Is the lens dirty? If so, clean the lens with a soft,
clean cloth.
The contrast on the
screen is too weak.
Adjust the contrast feature of the monitor. Is the
camera exposed to strong light? If so, change the
camera position.
The image on the
screen flickers.
Is the power frequency set properly in sync? If the
power frequency is not set correctly, the line lock
synchronization mode cannot be used. Set the
synchronization mode to INT.NTSC Model power
frequency in LL mode: 60 Hz.
The image on the
Does the camera face directly into the sun or
fluorescent lighting? If so, reposition camera.
screen is distorted.
15.1
AutoDome Junior Operation and Control
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Troubleshooting | en 183
Problem
Solution
Check all network connections
Ensure that the maximum distance
No Network
Connection
–
–
between any two Ethernet connections is
100 m (328 ft) or less.
If O.K., then:
–
If you are behind a firewall, ensure that the
Video Transmission mode is set to UDP.
a. Access the Settings Web page for the IP-
enabled device.
b. Expand the Service Settings link, then
click Network.
c. Select UDP from the Video Transmission
drop-down list. Then click Set.
Video is distorted
–
–
Navigate to the SETTINGS page.
Click the Advanced Link; then click the Camera
link, located in the left pane of the Settings
window.
(AutoDome Junior HD)
–
–
Click the Installer Menu, located under the
Camera link.
Select either 50 or 60 Hz from the Frequency
pull-down list.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
184 en | Troubleshooting
AutoDome Junior HD
15.2
LED Diagnostics
Use the following illustration to identify the LEDs (note the
position of the three screws to align your camera):
LED LED Color Function
State
Description
1
Green
Network Activity On
Network receiving and
transmitting data
No network activity
Link is active
Off
On
Off
2
3
Red
Network Link
Link failure
Bi-color LED Power/IP Board Green On IP board is running
Red On
Off
Green
IP board is booting
No power to the IP board
IP board is transmitting
Green/Red
Flashing
Red
video
IP board is resetting
Flashing
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
BVIP Firmware Updates | en 185
16
BVIP Firmware Updates
The AutoDome Junior HD incorporates a network video server
in the IP module. The primary function of the server is to
encode video and control data for transmission over a TCP/IP
network. The AutoDome Junior IP and HD also allows an
operator to update the BVIP firmware via the TCP/IP network.
The latest BVIP firmware is available on the Bosch Security
Systems Web site. To download the service pack from the Web,
navigate to www.boschsecurity.us, click the CCTV link, then
click Cameras, PTZ and navigate to the product page for the
AutoDome Junior HD. Then click the Software tab on the
product page.
16.1
Upgrading the AutoDome Junior IP or HD
The preferred method to update an AutoDome Junior IP or HD
is through a direct connection between the camera and a PC.
This method entails connecting the Ethernet cable from the
camera directly to the Ethernet port of a PC.
If the direct-connect method is not practical you can also
update the AutoDome Junior IP through a Local Area Network
(LAN). You cannot, however, update the AutoDome Junior IP or
HD through a Wide Area Network (WAN) or via the Internet.
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
186 en | BVIP Firmware Updates
AutoDome Junior HD
16.2
Beginning the Firmware Update Process
Use this procedure to connect to your AutoDome Junior HD and
to navigate to the Firmware Update page.
1. Launch Internet Explorer and type the IP address for the
AutoDome Junior HD in the Address bar and click Go.
Internet Explorer opens the Livepage view.
2. Click the SETTINGS link, located at the top of the page.
3. Click the Service link in the left pane.
4. Click the Maintenance link below the Service link.
5. Click the Search button and navigate to the firmware file
(*.fw). Then, click OK.
6. Click the Upload button.
7. Click OK to the warning message to continue the firmware
upload, or Cancel to stop the upload.
The page displays a progress bar as the firmware is
uploaded.
Note: Once the progress bar reaches 100% the system
opens the reset page. Allow the reset page to complete its
action.
8. Once the reset is complete the upgrade is complete.
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
187 en | Index
AutoDome Junior HD
Index
command numbers 100
commands
/reset 95
Symbols
/reset 95
A
Aux Off 100
Aux On 100
keyboard 100
activation key 178
alarm e-mail 160
alarm inputs
preset shot 101
non-supervised 83
normally closed non-supervised
84
normally open non-supervised
83
Set Shot 100, 101
Show Shot 100
conduit clamp 68
configuration download 177
Configuration Manager 93
configuration mode 108
configuring
alarm outputs 85
open collector output 85
alarm rule 162
alarm sensors 147
Audio settings 114, 141
Audio transmission 114, 141
auto-connect 153
AutoDome
IP AutoDome
/reset 95
Livepage 93
network settings 94
connect on alarm 150
connecting
IP
/reset 95
Livepage 93
network settings page 94
Aux Control tab 100
Aux Off 100
power 79, 80
connectors
pin mating 79, 80
control signals 121
controlling
image area 99
Controlling a Playback 105
Aux On 100
B
D
basic mode 108
Bookmarks 107
Browser window 95
date 118
date format 118
daylight saving time 118
default profile 128
default recording profile 146
default VCA profile 154
deleting recordings 145
Description 3, 46
device ID 115
C
cable
Ethernet 91
cables
power 77
camera
selection 97
camera name 116
CAT-5E 81
device name 109
devices
DVR 21
CAT-6 81
multiplexer 21
DHCP server 112
Dibos 90
CCD cameras 23, 34, 46, 66
changes in light level 156
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Index | en 188
DirectX 91
Display stamping 96
image resolution 104
image selection 97
displaying
image sensors 23, 34, 46, 66
initiator name 116
installing
on-screen menus 100
drywall ceiling 24
dual Streaming 124
dual streaming 89
DVR 21
base 30
drywall ceiling 24
power wires 77
surface mount 30
internal clock 118
IP 88
DynDNS 169
E
e-mail 160
address 92, 93, 112
encoding 89
alarm 99
video 89
audio 183
dual streaming 89
encoding 89
gateway address 93
module 88
multicast 89
port 92
record 89
snapshots 89
subnet mask 93
system requirements 90
UDP 183
encryption protocol 168
EPROM 176
Ethernet
cable 95
event log 100, 122, 123
F
false alarms 156
files
JPEG 89
MPEG-4 90
firewall 152, 167
firmware upload 176
formatting 145
FTP server 174, 175
IP address 166, 167
IPv4 166
IPv6 166
iSCSI settings 143
G
gateway 112, 166, 167
gateway address 93
general password 151
guard tour 138
J
JPEG 89
JPEG posting 174
JPEG posting interval 175
H
K
holidays 149
homing 87
HTTP port 168
HTTPS port 168
keyboard commands 100, 101
Aux Off command 100
Aux On 100
keypad 100
I
L
identification 109
IEE 802.3af 81
IEEE 802.1x 171
IGMP 173
language 120
licenses 178
Livepage 93
livepage 121
IGMP V2 89
image quality 174
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
189 en | Index
AutoDome Junior HD
processor load 105
M
processor load indicator 105
product name 120
profile configuration 125
profiles 113, 124
protocol
manufacturer logo 120
Media-replay 105
motion detector 154
motion detector defaults 154
motion detector object size 156
motion detector sensitivity 156, 158
mounting plate 73
MPEG ActiveX 91
IGMP V2 89
TCP/IP 88
UDP 89
R
MPEG-4 90
MTU value 167, 169
RADIUS 171
multicast 89
receiver password 151
recess mount 48, 56
record 89
multicast address 173
multicast connection 167, 173
multicasting 173
multiplexer 21
multi-unicast 173
recorded tour 138
recording media 143
recording profiles 145
recording scheduler 148
recording status 150
recording video sequences 104
reflections of light 156
relay 85
N
navigation 108
network 111, 165, 170
network settings page 94
networking
Replay 105
router 174
Ethernet cable 91
gateway address 93
IGMP V2 89
IP 88
IP address 92
port 92
subnet mask 93
TCP/IP 88
rules
for safety 3, 20
S
safety 3, 20
saving event log 123
saving system log 123
savng configuration 177
select area 157, 159
selecting a profile 124
sensor fields 157, 159
Set Shot 100, 101
Show Shot command 100
SMS 160
UDP 89
non-supervised alarms 83
number of connections 97
P
password 97, 109, 110, 117
pendant pipe mount 72
Playback button 106
port 92, 168, 174
post-alarm profile 147
post-alarm time 147
pre-alarm time 147
prefix length 167
preparing
snapshots 89, 104
SNMP 170
SNTP server 111, 119
software
DirectX 91
SSL certificate 177
SSL encryption 153
drywall ceiling 24
preset shot 101
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
AutoDome Junior HD
Index | en 190
standard recording profile values
146
storage media 143
W
wires
power 77
storage medium 115, 142
streaming 174
subnet mask 93, 112, 166
summer time 118
synchronize 111, 118
system log 99, 122, 123
T
tamper detection 157
target data rate 126
TCP 152, 167
TCP/IP 88
time 111, 118
time server 111, 119
IP address 111
protocol 111
time server IP address 119
time server protocol 119
time signal 111, 119
time zone 118
TLS 168
tour
guard 138
recorded 138
transmission protocol 152, 167
traps 171
TTL 174
U
UDP 89, 152, 167, 183
unicast 172
unit date 118
unit identification 109
unit name 109
unit time 111, 118
user name 109, 117
UTP CAT-5 81
V
video content analysis 154
video sensor 154
video transmission 183
VIDOS 90
VIP XD 90
VRM 142
Bosch Security Systems, Inc.
Installation Manual
F.01U.275.803 | 6.0 | 2012.11
Download from Www.Somanuals.com. All Manuals Search And Download.
191 en | Index
AutoDome Junior HD
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
192 en | Index
AutoDome Junior HD
F.01U.275.803 | 6.0 | 2012.11
Installation Manual
Bosch Security Systems, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Bosch Security Systems, Inc.
850 Greenfield Road
Lancaster, PA 17601
U.S.A.
www.boschsecurity.com
© Bosch Security Systems, Inc., 2012
Download from Www.Somanuals.com. All Manuals Search And Download.
|