Dinion2X IP Camera
NBN-498
en Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Table of Contents | en
3
Table of Contents
1
Safety
8
8
1.1
1.2
1.3
1.4
1.5
1.6
1.7
Safety precautions
Important safety instructions
Connection in applications
FCC & ICES compliance
UL certification
9
10
11
13
14
15
Bosch notices
Copyrights
2
Introduction
16
2.1
Features
16
3
System Information
Overview of functions
Progressive scan
18
18
18
18
18
19
19
19
19
19
19
19
20
20
20
20
20
20
20
22
3.1
3.1.1
3.1.2
3.1.3
3.1.4
3.1.5
3.1.6
3.1.7
3.1.8
3.1.9
3.1.10
3.1.11
3.1.12
3.1.13
3.1.14
3.1.15
3.1.16
3.1.17
3.2
Day/Night function
Wide dynamic range
Tri-streaming
ONVIF (Open Network Video Interface Forum)
Audio
Alarm I/O
Tamper detection and motion detectors
Video encoding
Multicast
Power-over-Ethernet
Encryption
Receiver
Recording
Snapshots
Backup
Configuration
Operation with external systems
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
4
en | Table of Contents
Dinion2X IP Camera
4
Planning
24
24
25
26
4.1
4.2
4.3
Unpacking
System requirements
Install players
5
Installation
27
27
28
29
30
31
32
33
34
35
35
36
36
36
37
37
5.1
Network (and power) connector
Power connector
5.2
5.3
Alarm and relay connector
Audio connectors
5.4
5.5
Video service monitor connector
Data connector
5.6
5.7
Lens mounting
5.8
Mounting the camera
Using the camera install menu
Back focus adjustment
Lens adjustment
5.9
5.10
5.11
5.11.1
5.11.2
5.11.3
5.12
DC-iris lens
Manual-iris lens
Video-iris lens
Reset button
6
Camera set-up
38
38
39
39
40
41
41
42
6.1
Camera menu navigation
Install menu
6.2
6.2.1
6.2.2
6.2.3
6.2.4
6.3
Pre-defined modes
Lens Wizard submenu
Network submenu
Defaults submenu
Day/Night switching
7
Browser connection
43
43
44
44
7.1
7.2
7.2.1
System requirements
Establishing the connection
Password protection in camera
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Table of Contents | en
5
7.3
Protected network
44
45
45
46
46
46
46
7.4
Connecting to a hardware decoder
Alarm connection
Connection established
LIVEPAGE
7.4.1
7.5
7.5.1
7.5.2
7.5.3
RECORDINGS
SETTINGS
8
Basic Mode
Basic Mode menu tree
Device Access
Camera name
Password
48
48
49
49
49
50
51
52
52
52
52
52
8.1
8.2
8.2.1
8.2.2
8.3
Date/Time
8.4
Network
8.5
Encoder Profile
Audio
8.6
8.7
Recording
8.7.1
8.8
Storage medium
System Overview
9
Advanced Mode
Advanced Mode menu tree
General
53
53
55
55
55
56
58
60
60
61
62
63
63
63
67
9.1
9.2
9.2.1
9.2.2
9.2.3
9.2.4
9.3
Identification
Password
Date/Time
Display Stamping
Web Interface
Appearance
9.3.1
9.3.2
9.3.3
9.4
LIVEPAGE Functions
Logging
Encoder
9.4.1
9.4.2
9.4.3
Privacy Masks
Encoder Profile
Encoder Streams
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
6
en | Table of Contents
Dinion2X IP Camera
9.5
9.6
Audio
68
69
Camera
9.6.1
9.6.2
9.6.3
9.6.4
9.6.5
9.6.6
9.6.7
9.7
Mode
69
ALC
70
Shutter/AGC
Day/night
71
72
Enhance
73
Color
74
Installer Options
Recording
75
77
9.7.1
9.7.2
9.7.3
9.7.4
9.7.5
9.8
Storage Management
Recording Profiles
Retention Time
Recording Scheduler
Recording Status
Alarm
77
80
81
82
83
84
9.8.1
9.8.2
9.8.3
9.8.4
9.8.5
9.8.6
9.8.7
9.8.8
9.9
Alarm Connections
Video Content Analyses (VCA)
VCA configuration- Profiles
VCA configuration - Scheduled
VCA configuration - Event triggered
Audio Alarm
84
87
88
94
96
97
Alarm E-Mail
98
Alarm Task Editor
Interfaces
100
101
101
101
102
103
103
107
108
109
110
111
111
113
9.9.1
9.9.2
9.9.3
9.10
Alarm input
Relay
COM1
Network
9.10.1
9.10.2
9.10.3
9.10.4
9.10.5
9.11
Network
Advanced
Multicasting
JPEG Posting
Encryption
Service
9.11.1
9.11.2
Maintenance
Licenses
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Table of Contents | en
7
9.11.3
System Overview
113
10
Operation via the browser
Livepage
114
114
114
115
115
115
115
115
116
116
116
117
117
10.1
10.1.1
10.1.2
10.1.3
10.1.4
10.1.5
10.1.6
10.1.7
10.1.8
10.1.9
10.2
Processor load
Image selection
View Control
Digital I/O
System Log / Event Log
Saving snapshots
Recording video sequences
Running recording program
Audio communication
Recordings page
10.2.1
Controlling playback
11
Troubleshooting
Function test
119
119
120
122
11.1
11.2
11.3
Resolving problems
Customer service
12
Maintenance
123
123
123
125
125
12.1
12.2
12.3
12.3.1
Testing the network connection
Communication with Terminal Program
Repairs
Transfer and disposal
13
Technical Data
Specifications
Dimensions
126
126
129
130
13.1
13.1.1
13.1.2
Accessories
Glossary
131
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
8
en | Safety
Dinion2X IP Camera
1
Safety
1.1
Safety precautions
DANGER!
High risk: This symbol indicates an imminently hazardous
situation such as "Dangerous Voltage" inside the product.
If not avoided, this will result in an electrical shock, serious
bodily injury, or death.
WARNING!
Medium risk: Indicates a potentially hazardous situation.
If not avoided, this could result in minor or moderate bodily
injury.
CAUTION!
Low risk: Indicates a potentially hazardous situation.
If not avoided, this could result in property damage or risk of
damage to the unit.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Safety | en
9
1.2
Important safety instructions
Read, follow, and retain for future reference all of the following
safety instructions. Follow all warnings on the unit and in the
operating instructions before operating the unit.
1. Clean only with a dry cloth. Do not use liquid cleaners or
aerosol cleaners.
2. Do not install unit near any heat sources such as radiators,
heaters, stoves, or other equipment (including amplifiers)
that produce heat.
3. Never spill liquid of any kind on the unit.
4. Take precautions to protect the unit from power and
lightning surges.
5. Adust only those controls specified in the operating
instructions.
6. Operate the unit only from the type of power source
indicated on the label.
7. Unless qualified, do not attempt to service a damaged unit
yourself. Refer all servicing to qualified service personnel.
8. Install in accordance with the manufacturer's instructions
in accordance with applicable local codes. Use only
attachments/accessories specified by the manufacturer.
Equipment change or modification could void the user's
guarantee or authorization agreement.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
10 en | Safety
Dinion2X IP Camera
1.3
Connection in applications
Power lines: An outdoor system should not be located in the
vicinity of overhead power lines, electrical lights, or power
circuits, or where it may contact such power lines or circuits.
When installing an outdoor system, extreme care should be
taken to keep from touching power lines or circuits, as this
contact may be fatal.
U.S.A. models only - refer to the National Electrical Code Article
820 regarding installation of CATV systems.
12 VDC / 24 VAC power source: This unit is intended to
operate with a limited power source. The unit is intended to
operate at either 12 VDC or 24 VAC (if PoE is not available).
User supplied wiring must be in compliance with electrical
codes (Class 2 power levels). If 24 VAC is used, do not ground
the 24 VAC supply at the terminals or at the unit's power supply
terminals.
PoE: Use only approved PoE devices. Power-over-Ethernet can
be connected at the same time as a 12 VDC or 24 VAC power
supply.
CAUTION!
The Low Voltage power supply unit must comply with EN/UL
60950. The power supply must be a SELV-LPS unit or a SELV -
Class 2 unit (Safety Extra Low Voltage - Limited Power Source).
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Safety | en 11
1.4
FCC & ICES compliance
FCC & ICES Information
(U.S.A. and Canadian Models Only)
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
–
–
reorient or relocate the receiving antenna;
increase the separation between the equipment and
receiver;
–
–
connect the equipment into an outlet on a circuit different
from that to which the receiver is connected;
consult the dealer or an experienced radio/TV technician
for help.
Intentional or unintentional modifications, not expressly
approved by the party responsible for compliance, shall not be
made. Any such modifications could void the user's authority to
operate the equipment. If necessary, the user should consult
the dealer or an experienced radio/television technician for
corrective action.
The user may find the following booklet, prepared by the
Federal Communications Commission, helpful: How to Identify
and Resolve Radio-TV Interference Problems. This booklet is
available from the U.S. Government Printing Office,
Washington, DC 20402, Stock No. 004-000-00345-4.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
12 en | Safety
Dinion2X IP Camera
Informations FCC et ICES
(modèles utilisés aux États-Unis et au Canada uniquement)
Suite à différents tests, cet appareil s'est révélé conforme aux
exigences imposées aux appareils numériques de classe B, en
vertu de la section 15 du règlement de la Commission fédérale
des communications des États-Unis (FCC), et en vertu de la
norme ICES-003 d'Industrie Canada. Ces exigences visent à
fournir une protection raisonnable contre les interférences
nuisibles lorsque l'appareil est utilisé dans le cadre d'une
installation résidentielle. Cet appareil génère, utilise et émet
de l'énergie de radiofréquences et peut, en cas d'installation ou
d'utilisation non conforme aux instructions, engendrer des
interférences nuisibles au niveau des radiocommunications.
Toutefois, rien ne garantit l'absence d'interférences dans une
installation particulière. Il est possible de déterminer la
production d'interférences en mettant l'appareil
successivement hors et sous tension, tout en contrôlant la
réception radio ou télévision. L'utilisateur peut parvenir à
éliminer les interférences éventuelles en prenant une ou
plusieurs des mesures suivantes:
–
Modifier l'orientation ou l'emplacement de l'antenne
réceptrice;
–
–
Éloigner l'appareil du récepteur;
Brancher l'appareil sur une prise située sur un circuit
différent de celui du récepteur;
–
Consulter le revendeur ou un technicien qualifié en radio/
télévision pour obtenir de l'aide.
Toute modification apportée au produit, non expressément
approuvée par la partie responsable de l'appareil, est
strictement interdite. Une telle modification est susceptible
d'entraîner la révocation du droit d'utilisation de l'appareil.
La brochure suivante, publiée par la Commission fédérale des
communications (FCC), peut s'avérer utile : Comment identifier
et résoudre les problèmes d’interférences de radio et de télévision.
Cette brochure est disponible auprès du U.S. Government
Printing Office, Washington, DC 20402, États-Unis, sous la
référence n° 004-000-00345-4.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Safety | en 13
1.5
UL certification
Disclaimer
Underwriter Laboratories Inc. ("UL") has not tested the
performance or reliability of the security or signaling aspects of
this product. UL has only tested fire, shock and/or casualty
hazards as outlined in UL's Standard(s) for Safety for Information
Technology Equipment, UL 60950-1. UL Certification does not
cover the performance or reliability of the security or signaling
aspects of this product.
UL MAKES NO REPRESENTATIONS, WARRANTIES, OR
CERTIFICATIONS WHATSOEVER REGARDING THE
PERFORMANCE OR RELIABILITY OF ANY SECURITY OR
SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.
Disposal - Your Bosch product was developed and
manufactured with high-quality material and components that
can be recycled and reused. This symbol means that
electronic and electrical appliances, which have reached the
end of their working life, must be collected and disposed of
separately from household waste material. Separate collecting
systems are usually in place for disused electronic and
electrical products. Please dispose of these units at an
environmentally compatible recycling facility, per European
Directive 2002/96/EC
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
14 en | Safety
Dinion2X IP Camera
1.6
Bosch notices
Video loss
Video loss is inherent to digital video recording; therefore,
Bosch Security Systems cannot be held liable for any damage
that results from missing video information. To minimize the
risk of lost digital information, Bosch Security Systems
recommends multiple, redundant recording systems, and a
procedure to back up all analog and digital information.
Copyright
This manual is the intellectual property of Bosch Security
Systems and is protected by copyright.
All rights reserved.
Trademarks
All hardware and software product names used in this
document are likely to be registered trademarks and must be
treated accordingly.
Note
This manual has been compiled with great care and the
information it contains has been thoroughly verified. The text
was complete and correct at the time of printing. The ongoing
development of the products may mean that the content of the
user guide can change without notice. Bosch Security Systems
accepts no liability for damage resulting directly or indirectly
from faults, incompleteness or discrepancies between the user
guide and the product described.
More information
For more information please contact the nearest Bosch Security
Systems location or visit www.boschsecurity.com
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Safety | en 15
1.7
Copyrights
The firmware 4.1 uses the fonts "Adobe-Helvetica-Bold-R-
Normal--24-240-75-75-P-138-ISO10646-1" and "Adobe-
Helvetica-Bold-R-Normal--12-120-75-75-P-70-ISO10646-1"under
the following copyright:
Copyright 1984-1989, 1994 Adobe Systems Incorporated.
Copyright 1988, 1994 Digital Equipment Corporation.
Permission to use, copy, modify, distribute and sell this
software and its documentation for any purpose and without
fee is hereby granted, provided that the above copyright
notices appear in all copies and that both those copyright
notices and this permission notice appear in supporting
documentation, and that the names of Adobe Systems and
Digital Equipment Corporation not be used in advertising or
publicity pertaining to distribution of the software without
specific, written prior permission.
This software is based in part on the work of the Independent
JPEG Group.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
16 en | Introduction
Dinion2X IP Camera
2
Introduction
2.1
Features
The Dinion2x IP Day/Night camera is a high-performance, smart
surveillance color camera. It incorporates 20-bit digital signal
processing and a wide dynamic range sensor for outstanding
picture performance under all lighting conditons.
The camera uses H.264 compression technology to give clear
images while reducing bandwidth and storage requirements. It
is also ONVIF compliant to improve compatibility during system
integration.
The camera operates as a network video server and transmits
video and control signals over data networks, such as Ethernet
LANs and the Internet.
The camera is easy to install and ready to use.
Features include:
–
–
–
–
–
–
–
–
–
–
–
–
–
Progressive scan
True Day/Night performance with switchable IR filter
1/3-inch CCD sensor with wide dynamic range
Tri-streaming (two H.264 streams and one M-JPEG stream)
Complies with the ONVIF standard for wide compatibility
Two-way audio and audio alarm
Alarm input and alarm output to external devices
Dynamic engine with Smart BLC
Six pre-programmed operation modes
Adaptive dynamic noise reduction
Enhanced video motion detection
Video and data transmission over IP data networks
Multicast function for simultaneous picture transmission to
multiple receivers
–
–
–
–
Integrated Ethernet interface (10/100 Base-T)
Power-over-Ethernet (PoE)
Remote control of all built-in functions via TCP/IP
Data interface RS485/RS422/RS232 for control of pan or
tilt heads or motorized zoom lenses (PTZ control)
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
–
Introduction | en 17
Password protection to prevent unauthorized connection
or configuration changes
–
–
Event-driven, automatic connection (for example, at
switch-on and for alarms)
Fast, convenient configuration using the integrated Web
server and a browser
–
–
Firmware update through flash memory
Convenient upload and download of configuration data
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
18 en | System Information
Dinion2X IP Camera
3
System Information
3.1
Overview of functions
The camera incorporates a network video server. Its primary
function is to encode video and control data for transmission
over an IP network. With its H.264 encoding, it is ideally suited
for IP communication and for remote access to digital video
recorders and IP systems. The use of existing networks means
that integration with CCTV systems or local networks can be
achieved quickly and easily. Video images from a single camera
can be simultaneously received on several receivers.
3.1.1
3.1.2
Progressive scan
The camera captures and processes progressively scanned
images. When there is fast motion in a scene, progressively
scanned images are generally sharper than interlaced images.
Day/Night function
The Day/Night function provides enhanced night viewing by
increasing the IR sensitivity. The motorized IR filter can be
removed in low-light or IR illuminated applications. The IR filter
switches from color to monochrome automatically by sensing
the illumination level. In auto switching mode the camera
prioritizes motion (the camera gives sharp images without
motion blur) or color (the camera gives color pictures as long as
the light level permits).
3.1.3
Wide dynamic range
A unique combination of 20-bit digital video processing that
enhances sensitivity and 2X-Dynamic which extends the
dynamic range, provides a sharper, more detailed image with
outstanding accuracy in color reproduction. The 20-bit digital
signal is automatically processed to optimally capture the detail
in both the high and low light areas of the scene
simultaneously, maximizing the information visible in the
picture.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
System Information | en 19
3.1.4
Tri-streaming
Tri-streaming allows the data stream to be encoded
simultaneously according to three different, individually
customized profiles. This creates two full H.264 streams that
can serve different purposes and an additional M-JPEG stream.
3.1.5
ONVIF (Open Network Video Interface Forum)
The camera complies to the ONVIF standard which means that
it is easier to install and integrate into larger systems. The
ONVIF standard is a global standard for the interface of network
video products.
3.1.6
3.1.7
3.1.8
Audio
Two-way duplex audio is available in the unit for live voice
communications or audio recording.
Alarm I/O
The alarm input can be used to control the functionality of the
unit. An alarm output can control external devices.
Tamper detection and motion detectors
The camera offers a wide range of configuration options for
alarm signaling in the event of tampering with the camera. An
algorithm for detecting movement in the video image is also
part of the scope of delivery and can optionally be extended to
include special video analysis algorithms.
3.1.9
Video encoding
The camera uses the H.264 compression standards. Thanks to
efficient encoding, the data rate remains low even with high
image quality and can also be adapted to local conditions
within wide limits.
3.1.10
Multicast
In suitably configured networks, the multicast function enables
simultaneous, real time transmission to multiple receivers. The
prerequisite for this is that the UDP and IGMP V2 protocols are
implemented on the network.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
20 en | System Information
Dinion2X IP Camera
3.1.11
Power-over-Ethernet
Power for the camera can be supplied via a Power-over-
Ethernet compliant network cable connection. With this
configuration, only a single cable connection is required to
view, power, and control the camera.
3.1.12
Encryption
The unit offers a variety of options for protection against
unauthorized reading. Web browser connections can be
protected using HTTPS. Protect the control channels via the
SSL encryption protocol. With an additional license, the user
data itself can be encrypted.
3.1.13
Receiver
H.264 compatible hardware decoders can be used as a
receiver. Computers with decoding software such as VIDOS, or
computers with the Microsoft Internet Explorer web browser
installed, can also be used as receivers.
3.1.14
3.1.15
Recording
The camera can be used with an iSCSI server connected via the
network to store long-term recordings.
Snapshots
Individual video frames (snapshots) can be called up as JPEG
images, stored on the hard drive, or displayed in a separate
browser window.
3.1.16
3.1.17
Backup
The browser application has an icon for saving the video images
provided by the unit as a file on your computer's hard drive.
Clicking this icon stores the video sequences and they can be
replayed with the Player from Bosch Security Systems included
with the package.
Configuration
The camera can be configured using a browser on the local
network (Intranet) or from the Internet. Similarly, firmware
updates and rapid loading of device configurations are also
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
System Information | en 21
possible. Configuration settings can be stored as files on a
computer and copied from one camera to another.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
22 en | System Information
Dinion2X IP Camera
3.2
Operation with external systems
The camera can be used with a variety of Bosch software and
hardware systems:
–
–
–
–
Bosch Video Management System
VIDOS video management software
DiBos 900 Series digital video recorder
Divar 700 Series digital video recorder
Note:
When connected to any of these systems, many of the camera
configuration parameters are controlled by the system and not
by the settings made via a web browser connected to the
camera.
Bosch Video Management System
The Bosch Video Management System is a unique enterprise IP
video surveillance solution that provides seamless management
of digital video, audio, and data across any IP network. It is
designed to work with Bosch CCTV products as part of a total
video surveillance management system. Integrate your existing
components into one easy-to-manage system, or use Bosch’s
full-line capabilities and benefit from a complete surveillance
solution based on cutting-edge technology and years of
experience.
VIDOS
The camera video server and VIDOS software combine to
provide a high-performance system solution. VIDOS is software
for operating, controlling, and administering CCTV installations
(such as surveillance systems) at remote locations. It runs
under Microsoft Windows operating systems. Its main job is
decoding video, audio, and control data from a remote
transmitter. There are many options available for operation and
configuration when using a camera with VIDOS.
DiBos 900 Series
The camera is also designed for use with DiBos 900 Series
Video Recorders. DiBos can record up to 32 video and audio
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
System Information | en 23
streams, and is available as software or as a hybrid DVR with
additional analog camera and audio inputs. DiBos supports
various functions of the camera, such as controlling relays,
remote control of peripheral devices, and remote configuration.
DiBos can use alarm inputs to trigger actions and, when motion
detection Motion+ is active, can record the relevant cells,
making intelligent motion detection possible.
Divar 700 Series
The Divar 700 Series of digital video recorders can view and
record images from the camera via a network connection. The
Divar 700 Series controls the camera so that the correct
settings are used.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
24 en | Planning
Dinion2X IP Camera
4
Planning
4.1
Unpacking
Unpack carefully and handle the equipment with care. The
packaging contains:
–
–
–
–
–
–
–
Dinion2X IP camera
CCD protection cap (mounted on camera)
Power connector
Alarm I/O connector
Data connector
Spare lens connector (male)
DVD ROM (mini)
–
–
–
–
–
–
–
–
–
–
Manual
System requirements
Configuration Manager
BVIP Lite Suite
MPEG ActiveX control
DirectX control
Microsoft Internet Explorer
Sun JVM
Player and Archive Player
Adobe Acrobat Reader
–
–
Quick install instructions
Safety instructions
If equipment has been damaged during shipment, repack it in
the original packaging and notify the shipping agent or supplier.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Planning | en 25
4.2
System requirements
–
–
–
–
Computer with Windows XP/Vista operating system,
network access, and Microsoft Internet Explorer web
browser version 7.0 or later
or
Computer with Windows XP/Vista operating system,
network access and reception software, for example
VIDOS, Bosch VMS, or DIBOS 900 Series
or
H.264 compatible hardware decoder from
Bosch Security Systems (such as VIP XD) as a receiver and
a connected video monitor
or
Divar 700 Series Digital Video Recorder
The minimum PC requirements are:
–
Operating platform: A PC running Windows XP or
Windows Vista with IE 7.0
–
–
–
–
–
Processor: Dual core, 3.0 GHz
RAM memory: 256 MB
Monitor resolution: 1024 x 768
Network interface: 100-BaseT
DirectX: 9.0c
Make sure the graphics card is set to 16-bit or 32-bit color
depth and that Sun JVM is installed on your PC. To play back
live video images, an appropriate ActiveX must be installed on
the computer. If necessary, install the required software and
controls from the product DVD provided. For further assistance,
contact your PC system administrator.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
26 en | Planning
Dinion2X IP Camera
4.3
Install players
Play back saved-video sequences using the Player from
Bosch Security Systems. This can be found on the DVD-ROM
supplied.
to play back saved sequences using the Player, suitable ActiveX
software must be installed on the computer.
1. Insert the DVD into the DVD-ROM drive of the computer. If
the DVD does not start automatically, open the DVD in
Windows Explorer and double-click the index.html file to
start the installation.
2. Select a language from the list box at the top.
3. Click Tools in the menu.
4. Click Archive Player; the installation starts.
5. Follow the instructions in the installation program. The
Archive Player is installed together with the Player.
6. After a successful installation, two new icons for the Player
and the Archive Player appear on the desktop.
7. Double-click the Player icon to start the Player.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Installation | en 27
5
Installation
CAUTION!
Installation should only be performed by qualified service
personnel in accordance with the National Electrical Code or
applicable local codes.
5.1
Network (and power) connector
AU
D
IO IN
AU
D
IO OUT
–
+
AL
ARM
E
T
H
12 VDC
24
1
2
3
4
5
6
V
A
C
P
o
E
VIDEO
DA
TA
1
2
3
4
5
6
UTP Cat 5 RJ45
Figure 5.1 Network connection
–
–
Connect the camera to a 10/100 Base-T network.
Use screened UTP Category 5e cable with RJ45 connectors
(the camera network socket is Auto MDIX compliant).
Power can be supplied to the camera via the Ethernet
cable compliant with the Power-over-Ethernet
(IEEE 802.3af) standard.
–
The multicolored LED beside the Ethernet connection indicates
Power (red), IP connection (green) and IP traffic (green
flashing). It can be disabled in the Settings/Camera Settings/
Install options menu.
By default, power is supplied to the camera via the Ethernet
cable, compliant with the Power-over-Ethernet standard.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
28 en | Installation
Dinion2X IP Camera
5.2
Power connector
AUDIO IN
AUDIO OUT
–
+
ALA
RM
E
2 VDC
24
1
2
3
V
AC
E
DA
TA
1
2
3
4
5
6
5 mm
0.2 in
Figure 5.2 Power connection
Connect power from a 24 VAC or 12 VDC class 2 power supply
as follows:
–
–
–
Use AWG16 to 22 stranded wire or AWG16 to 26 solid
wire; cut back 5 mm (0.2 in) of insulation.
Loosen the screws of the supplied 2-pole connector and
insert the wires.
Tighten the screws and insert the 2-pole connector into
the power socket of the camera.
Note:
For a DC supply the polarity is important. Incorrect polarity
does not damage the camera but it will not switch on.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Installation | en 29
5.3
Alarm and relay connector
Alarm
1
2
3
4
5
6
5 mm
(0.2 in)
Figure 5.3 Alarm and relay connector pins
Pin
1
Alarm socket
Alarm in 1
2
Alarm in 2
3
Relay out contact 1
Ground
4
5
Ground
6
Relay out contact 2
–
Max. wire diameter AWG 22-28 for both stranded and
solid; cut back 5 mm (0.2 in) of insulation.
Alarm output relay switching capability: Max voltage 30VAC
or +40 VDC. Max 0.5 A continuous, 10 VA.
Alarm in: TTL logic, +5V nominal, +40 VDC max, DC coupled
with 22 kOhm pull-up to +3.3 V.
–
–
–
–
Alarm in: configurable as active low or active high.
Max. 42 V allowed between camera ground and each of the
relay pins.
Use the alarm input to connect external alarm devices such as
door contacts or sensors. A zero potential make-contact or
switch can be used as the actuator (use a bounce-free contact
system).
Use the alarm relay output for switching external devices such
as lamps or sirens.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
30 en | Installation
Dinion2X IP Camera
5.4
Audio connectors
Line
GND
AU
D
IO
IN
AU
D
IO
O
UT
–
+
AL
ARM
E
T
H
12 VDC
24
1
2
3
4
5
6
V
A
C
P
o
E
VIDEO
DA
TA
1
2
3
4
5
6
Figure 5.4 Audio connectors
Connect audio devices to the Audio In and Audio Out
connectors.
The unit has full-duplex mono audio. The two-way
communication can be used to connect a speaker or door
intercom system. The audio input signal is transmitted in sync.
with the video signal.
Audio input: Line input level (not suitable for direct
microphone signal); impedance 9 kOhm typical; 5.5 Vpp
maximum input voltage.
Audio output: Line output level (not suitable for direct speaker
connection); impedance 16 Ohm minimum; 3 Vpp maximum
output voltage.
Wiring: Shielded audio connection cable is advised. Observe
maximum cable lengths for audio line input and output levels.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Installation | en 31
5.5
Video service monitor connector
AU
D
IO IN
AU
D
IO OUT
–
+
AL
ARM
E
T
H
12 VDC
24
1
2
3
4
5
6
V
A
C
P
o
E
VIDEO
DA
TA
1
2
3
4
5
6
Figure 5.5 Video BNC connector
1. Connect a service monitor to the composite video BNC
connector to aid installation.
2. Open the side panel on the camera and press the center
button for longer than 2 seconds. This stops the IP video
stream and enables the video analog output.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
32 en | Installation
Dinion2X IP Camera
5.6
Data connector
DATA
1
2
3
4
5
6
5 mm
(0.2 in)
Figure 5.6 Data connector pins
Pin
1
Data socket
Ground
2
RxD / Rx+
CTS / Rx-
Ground
3
4
5
TxD / Tx-
RTS / Tx+
6
The data connector is used to connect the control data coming
out of the camera to external devices. RS485, RS422, and
RS232 is supported by this data connection.
Note:
To ensure surge and electrostatic protection, keep the cable
length between the camera and external device to less than 3
meters.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Installation | en 33
5.7
Lens mounting
The camera accepts CS-mount lenses. C-mount lenses can be
mounted using a lens adapter ring. DC-iris lenses are
recommended for best picture performance. The camera
automatically detects the type of lens and optimizes
performance accordingly. A spare male lens connector is
provided.
CAUTION!
To avoid damaging the CCD sensor when using a C-mount lens,
make sure the supplied lens adapter ring is mounted onto the
camera before mounting the lens.
CAUTION!
Lenses weighing more than 0.5 kg (1.1lbs) must be separately
supported.
Bosch
Bosch
Figure 5.8 Lens connector
Figure 5.7 Mounting a lens
Pin Video iris lens
DC iris lens
1
2
3
4
Supply (11.5V 0.5, 50mA max.)
Damp -
Damp +
Drive +
Drive -
Not used
Video signal 1Vpp 1kOhm
Ground
Note
If a short circuit is detected on the lens connector, the message
LENS SHORT CIRCUIT is shown. The lens circuit is
automatically disabled to avoid internal damage. Remove the
lens connector and check the pin connections.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
34 en | Installation
Dinion2X IP Camera
5.8
Mounting the camera
The camera can be mounted either from the top or from the
bottom (1/4" 20 UNC thread).
Figure 5.9 Mounting a camera
CAUTION!
The CCD image sensors are highly sensitive and require special
care for proper preformance and extended lifetime. Do not
expose them, or point the camera/lens, to direct sunlight.
Do not obstruct the free flow of air around the camera.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Installation | en 35
5.9
Using the camera install menu
Five keys, located behind the side door panel, are used for
accessing the camera menu.
To open the install menu press and hold the center key for
approximately two seconds. The BNC video output is activated
and the Install menu appears on the monitor.
5.10
Back focus adjustment
To optimize picture sharpness in both bright and low-level
lighting, adjust the back focus. Use the camera's unique Lens
Wizard. This ensures that the object of interest always remains
in focus, even when focusing at the maximum lens iris opening
(for example, at night).
–
When back focusing varifocal lenses, adjust to obtain a
sharp picture in both wide-angle and tele positions for
both far and near focus.
–
When back focusing zoom lenses, ensure the object of
interest remains in focus throughout the entire zoom range
of the lens.
To adjust back focus:
1. Slide open the door panel at the side of the camera.
2. Unlock the back focus locking button.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
36 en | Installation
Dinion2X IP Camera
3. Press and hold the center key for more than 2 seconds
until the Install menu appears.
4. Select Len Wizard and move cursor to the Set Back Focus
Now item.
5. Turn the back focus adjustment as required.
6. Lock the back focus locking button.
7. Press and hold the center key for more than 2 seconds
until all the menus disappear.
8. Close the side door panel.
5.11
Lens adjustment
5.11.1
DC-iris lens
1. Unlock the back focus locking button.
2. Access the Lens Wizard menu.
3. Set Back Focus Now is highlighted in the menu.
4. Turn the back focus adjustment as required.
5. Lock the back focus locking button.
6. Exit the menu.
5.11.2
Manual-iris lens
1. Unlock the back focus locking button.
2. Adjust the lens to the maximum lens opening.
3. Turn the back focus adjustment as required.
4. Lock the back focus locking button.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Installation | en 37
5.11.3
Video-iris lens
1. Unlock the back focus locking button.
2. Access the Lens Wizard menu.
3. Set Back Focus Now is highlighted in the menu.
4. Turn the back focus adjustment as required.
5. Lock the back focus locking button.
6. Select Set LVL in the menu; the Level bar appears.
7. Point the camera at the scene it will be mostly viewing.
8. Adjust the level potentiometer located on the lens until the
Level bar is in the central position.
9. Exit the menu.
The best performance with video iris lenses is obtained when
the peak/average potentiometer of the lens matches the peak/
average balance configuration setting.
5.12
Reset button
AU
D
IO IN
AU
D
IO OUT
–
+
AL
ARM
E
T
H
12 VDC
24
1
2
3
4
5
6
V
A
C
P
o
E
VIDEO
DA
TA
1
2
3
4
5
6
Figure 5.10 Reset button
With the power on, use a small pointed object to press and hold
the reset button for more than 10 seconds to restore the
factory defaults. This is useful to restore the default IP address
or to restore a previous version of the firmware if uploading a
new version fails.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
38 en | Camera set-up
Dinion2X IP Camera
6
Camera set-up
The camera normally provides an optimal picture without the
need for further adjustments. Configuration of the camera is
carried out remotely via the network using a web browser.
However, the camera also has a set-up menu in which basic
installation settings (lens wizard, IP address) can be accessed.
To view this menu, connect a monitor to the composite video
output of the camera.
6.1
Camera menu navigation
Five keys are used for navigating through menu system.
Up key
Menu/Select key (center)
Right key
Down key
Left key
Figure 6.1 Navigation
–
To open the install menu and enable the analog video
output, press and hold the center key for approximately
two seconds. This turns off the IP video stream.
Use the up or down keys to scroll through a menu.
Use the left or right keys to move through options or to set
parameters.
–
–
–
–
When in a menu, quickly double-press the menu/select key
to restore the selected item to its factory default.
To close all menus at once hold down the menu/select key
until the menu display disappears or continually select the
Exit item. (This turns the IP video stream back on.)
Some menus automatically close after about two minutes; other
menus have to be closed manually.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Camera set-up | en 39
6.2
Install menu
When the Install menu is opened, the MAC address of the unit
is shown. This is factory set and cannot be changed. (To ensure
that the correct MAC address is displayed, wait 20 seconds
after power-up before opening the Install menu.)
The items in the Install menu include the Mode selection, the
Lens Wizard submenu, the Network submenu, and the Defaults
submenu.
Note:
Camera parameter set-up is done via IP. See
Section 9.6 Camera for the specific camera menus.
6.2.1
Pre-defined modes
There are six pre-defined modes with settings to make
configuration easier. Select one of the six pre-defined modes in
the Install/Mode submenu. The modes are defined as follows;
1. 24-hour
Default installation mode to provide stable pictures over a
24-hour period. These settings are optimized for out-of-
the-box installation.
2. Traffic
Capture high-speed objects using default shutter in
variable lighting conditions.
3. Low light
Provide extra enhancement, such as AGC and SensUp to
make usable pictures in low-light conditions.
4. Smart BLC
Settings optimized to capture details in high contrast and
extremely bright-dark conditions.
5. Low noise
Enhancements are set to reduce picture noise. Useful for
conditional refresh DVR and IP storage systems because
reducing noise reduces the amount of storage required.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
40 en | Camera set-up
Dinion2X IP Camera
6. Infrared
Use this mode if the camera is viewing a scene lit by
infrared light.
6.2.2
Lens Wizard submenu
Item
Selection
Description
Lens type
Auto,
Auto: - automatically selects the type of
lens.
Manual, DC-
iris, Video
Manual, DC-iris, Video modes: select
the matching lens type to force the
camera to the correct lens mode.
Detected
Shows the type of lens detected when
auto lens detection is used.
Set Backfocus
now
Select to fully open the iris. Follow the
instructions below for setting the
backfocus for your particular lens type.
After focusing the object of interest
remains in focus under bright and low
light conditions.
Set LVL
EXIT
Only for video-iris lenses.
Adjust the level control on the lens to
center the level detector indicator (see
below).
Returns to Install menu.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Camera set-up | en 41
6.2.3
Network submenu
To operate the camera in your network, a network-valid IP
address must be assigned. The factory default IP address is
192.168.0.1
Function
Selection
Description
IP Address
Enter an IP address for the camera. Use
LEFT/RIGHT to change position in the
address, use UP/DOWN to select the digit.
Use SELECT to exit the address edit
screen.
Subnet
Mask
Enter the Subnet mask (default
255.255.255.0).
Gateway
DHCP
Enter a Gateway address.
If the network has a DHCP server for
dynamic IP address allocation, set this
parameter to On to activate the automatic
acceptance of DHCP-assigned IP
addresses.
Exit
Return to the Install menu.
The new IP address, subnet mask, and gateway address are set
when leaving the menu. The camera reboots internally and the
new values are set after a few seconds.
6.2.4
Defaults submenu
Item
Selection
Description
Restore All?
No, Yes
Restores all settings of the six modes
to their default (factory) values. Select
YES then press the Menu/Select
button to restore all values.
When completed the message
RESTORED! is shown.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
42 en | Camera set-up
Dinion2X IP Camera
6.3
Day/Night switching
The camera is equipped with a motorized IR filter. The
mechanical IR filter can be removed in low-light or IR
illuminated applications by software configuration settings.
If Auto switching mode is selected, the camera automatically
switches the filter depending on the observed light level. The
switching level is programmable. In Auto switching mode the
camera prioritizes motion (the camera gives sharp images
without motion blur as long as the light level permits) or color
(the camera gives color pictures as long as the light level
permits). The camera recognizes IR illuminated scenes to
prevent unwanted switching to color mode.
There are four different methods of controlling the IR filter:
–
–
–
via an alarm input,
automatically, based on the observed light levels, or
as part of the programmable mode profile.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Browser connection | en 43
7
Browser connection
A computer with Microsoft Internet Explorer can be used to
receive live images from the camera, control cameras, and
replay stored sequences. The camera is configured over the
network using the browser (or via the supplied Configuration
Manager). The configuration options using the menu system of
the camera itself are limited to setting up the lens and network.
Note:
The camera can also be connected to DIBOS 900 Series,
VIDOS, Bosch Video Management System, and Divar 700 Series
Digital Video Recorder, as well as third party video management
systems.
7.1
System requirements
–
Microsoft Internet Explorer version 7.0 or higher
Monitor: resolution at least 1024 × 768 pixels, 16 or 32 bit
color depth
–
–
–
Sun JVM installed
Intranet or Internet network access
The Web browser must be configured to enable Cookies to be
set from the IP address of the unit.
In Windows Vista, deactivate protected mode on the Security
tab under Internet Options.
Read the information in the System Requirements document
on the product DVD supplied and, if necessary, install the
required programs and controls.
To play back live video images, an appropriate ActiveX must be
installed on the computer. If necessary, the required software
and controls can be installed from the product DVD provided.
a. Insert the mini-DVD into the DVD-ROM drive of the
computer. If the DVD does not start automatically,
open the root directory of the DVD in Windows
Explorer and double click MPEGAx.exe.
b. Follow the on-screen instructions.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
44 en | Browser connection
Dinion2X IP Camera
7.2
Establishing the connection
The camera must be assigned a valid IP address to operate on
your network. The default address pre-set at the factory is
192.168.0.1
1. Start the Web browser.
2. Enter the IP address of the camera as the URL.
Note:
If the connection is not established, the maximum number of
possible connections may already have been reached.
Depending on the device and network configuration, up to 25
web browsers, or 50 VIDOS or Bosch VMS connections are
supported.
7.2.1
Password protection in camera
A camera offers the option of limiting access across various
authorization levels. If the camera is password-protected, a
message to enter the password appears.
1. Enter the user name and the associated password in the
appropriate fields.
2. Click OK. If the password is correct, the desired page is
displayed.
7.3
Protected network
If a Radius server is used for network access control (802.1x
authentication), the camera must be configured first. To
configure the camera for a Radius network, connect it directly
to a PC via a crossed network cable and configure the two
parameters, Identity and Password. Only after these have been
configured can communication with the camera via the network
occur.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Browser connection | en 45
7.4
Connecting to a hardware decoder
A compatible H.264 hardware decoder with a monitor can be
connected to the camera using an Ethernet network
connection. Cameras are designed to automatically connect
with other BVIP devices with the correct configuration. The
units only need to be part of the same closed network. In this
way it is possible to cover large distances with little installation
or cabling effort.
7.4.1
Alarm connection
With the appropriate configuration, a connection between
camera and decoder is established automatically when an alarm
is triggered. After a short time, the live video image from the
transmitter is shown on the connected monitor. In this case, no
computer is needed to establish the connection
Note:
Make sure the devices are configured for the network
environment and that the correct IP address for the remote
location is set on the Alarm connections configuration page.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
46 en | Browser connection
Dinion2X IP Camera
7.5
Connection established
When a connection is established, the LIVEPAGE is initially
displayed. The application title bar displays three items:
LIVEPAGE, RECORDINGS, SETTINGS.
Note:
The RECORDINGS link is only visible if a storage medium is
available.
Figure 7.1 Livepage
7.5.1
7.5.2
7.5.3
LIVEPAGE
The LIVEPAGE is used to display and control the video stream.
Refer to Section 10 Operation via the browser, page 114 for more
information.
RECORDINGS
Click RECORDINGS in the application title bar to open the
playback page. Refer to Section 10 Operation via the browser,
page 114 for more information.
SETTINGS
Click SETTINGS in the application title bar to configure the
camera and the application interface. A new page containing
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Browser connection | en 47
the configuration menu is opened. All settings are stored in the
camera memory so that they are retained, even if the power is
interrupted.
Changes that influence the fundamental functioning of the unit
(for example, firmware updates) can only be made using the
configuration menu.
The configuration menu tree allows all parameters of the unit to
be configured. The configuration menu is divided into Basic
Mode and Advanced Mode.
Refer to Section 8 Basic Mode, page 48 for more information on
basic settings; refer to Section 9 Advanced Mode, page 53 for
more information on advanced settings.
Note:
It is recommended that only expert users or system
administrators use the Advanced Mode.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
48 en | Basic Mode
Dinion2X IP Camera
8
Basic Mode
8.1
Basic Mode menu tree
The basic mode configuration menu allows a set of basic
camera parameters to be configured.
Basic Mode
>
>
>
>
>
>
>
Device Access
Date/Time
Network
Encoder Profile
Audio
Recording
System Overview
To view the current settings:
1. If necessary, click the Basic Mode menu to expand it. The
sub-menus are displayed.
2. Click a sub-menu. The corresponding page is opened.
The settings are changed by entering new values or by selecting
a pre-defined value in a list field.
Saving changes
After making changes in a window, click Set to send the new
settings to the device and save them there.
Clicking Set saves only the settings in the current window.
Changes in any other windows are ignored.
Click SETTINGS in the applications title bar to close the
window without saving the changes.
Note:
Device time settings are lost after 1 hour without power if no
central time server is selected.
Note:
When entering names do not use any special characters, for
example &. Special characters are not supported by the internal
recording management system.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Basic Mode | en 49
8.2
Device Access
8.2.1
Camera name
Assign a name to assist in identification. This name simplifies
the management of multiple devices in more extensive systems.
The name is used for remote identification, for example, in the
event of an alarm. Enter a name that makes it as easy as
possible to identify the location unambiguously.
8.2.2
Password
A password prevents unauthorized access to the device. The
device recognizes three authorization levels: service, user, and
live.
–
service is the highest authorization level. Entering the
correct password gives access to all the functions of the
camera and allows all configuration settings to be
changed.
–
–
user is the middle authorization level. This user can
operate the device, play back recordings, and also control
a camera but cannot change the configuration.
live is the lowest authorization level. It can only be used to
view the live video image and switch between the different
live image displays.
Use the various authorization levels to limit access. Proper
password protection is only guaranteed if all higher
authorization levels are also protected with a password. For
example, if a live password is assigned, a service and a user
password should also be set. When assigning passwords,
always start from the highest authorization level, service, and
use different passwords.
Password
Define and change a separate password for each level while
logged in as service or if the device is not protected by a
password. Enter the password for the selected level.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
50 en | Basic Mode
Dinion2X IP Camera
Confirm password
Re-enter the new password to ensure that there are no typing
mistakes.
The new password is only saved after clicking Set. Therefore,
click Set immediately after entering and confirming the
password, even if assigning a password at another level.
8.3
Date/Time
Device date, time and zone
If there are multiple devices operating in the system or
network, it is important to synchronize their internal clocks. For
example, it is only possible to identify and correctly evaluate
simultaneous recordings when all devices are operating on the
same time.
As the device time is controlled by the internal clock, it is not
necessary to enter the day or date of the week. These are set
automatically. The time zone in which the system is located is
also set automatically.
1. Click Sync to PC to apply the system time from your
computer to the device.
Time server IP address
The camera can receive the time signal from a time server using
various time server protocols and then use it to set the internal
clock. The device polls the time signal automatically once every
minute. Enter the IP address of a time server.
Time server type
Select the protocol that is supported by the selected time
server. It is recommended to select the SNTP server protocol.
This protocol provides high accuracy and is required for special
applications and future function extensions. Select Time server
if the server uses the RFC 868 protocol.
Note:
It is important to ensure that the date/time is correct for
recording. An incorrect date/time setting could prevent correct
recording.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Basic Mode | en 51
8.4
Network
Use the settings on this page to integrate the device into a
network. Some changes only take effect after a reboot. In this
case, the Set button changes to Set and Reboot.
1. Make the desired changes.
2. Click Set and Reboot.
–
The device is rebooted and the changed settings are
activated. If the IP address, subnet mask, or gateway
address is changed, then the device is only available
under the new addresses after the reboot.
DHCP
If the network has a DHCP server for dynamic IP address
allocation, set this parameter to On to activate the automatic
acceptance of DHCP-assigned IP addresses.
Note:
Certain applications (for example, Bosch Video Management
System) use the IP address for the unique assignment of the
device. If using these applications, the DHCP server must
support the fixed assignment between IP address and MAC
address, and must be appropriately set up so that, once an IP
address is assigned, it is retained each time the system is
rebooted.
IP address
Enter the desired IP address for the camera. The IP address
must be valid for the network.
Subnet mask
Enter the appropriate subnet mask for the set IP address.
Gateway address
Enter the IP address of the gateway to establish a connection to
a remote location in a different subnet. Otherwise, this field can
remain empty (0.0.0.0).
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
52 en | Basic Mode
Dinion2X IP Camera
8.5
Encoder Profile
Select a profile for encoding the video signal. Pre-programmed
profiles are available that give priority to different parameters.
When a profile is selected, its details are displayed.
8.6
8.7
Audio
Switch the camera audio On or Off. Adjust the input and output
levels with the sliders.
Recording
Record the images from the camera to a storage medium. For
long-term authoritative images, it is essential to use a
Divar 700 Series Digital Video Recorder or an appropriately
sized iSCSI system.
8.7.1
Storage medium
1. Select the required storage medium from the list.
2. Click Start to start recording or Stop to end recording.
8.8
System Overview
This page provides general information on the hardware and
firmware system, including version numbers. No items can be
changed on this page but they can be copied for information
purposes when troubleshooting.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 53
9
Advanced Mode
9.1
Advanced Mode menu tree
The advanced mode configuration menu contains all camera
parameters that can be configured.
Advanced Mode
>
>
>
>
>
>
>
>
>
General
Web Interface
Encoder
Camera
Recording
Alarm
Interfaces
Network
Service
To view the current settings:
1. Click the Advanced Mode menu to expand it. The
associated menu sub-headings are displayed.
2. Click a menu sub-heading to expand it.
3. Click a sub-menu. The corresponding page is opened.
The settings are changed by entering new values or by selecting
a pre-defined value in a list field.
Saving changes
After making changes in a window, click Set to send the new
settings to the device and save them there.
Clicking Set saves only the settings in the current window.
Changes in any other windows are ignored.
Click SETTINGS in the applications title bar to close the
window without saving the changes made.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
54 en | Advanced Mode
Dinion2X IP Camera
Note:
Device time settings are lost after 1 hour without power if no
central time server is selected.
Note:
When entering names do not use any special characters, for
example &. Special characters are not supported by the internal
recording management system.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 55
9.2
General
General
>
>
>
>
Identification
Password
Date/Time
Display Stamping
9.2.1
Identification
Camera ID
Each device should be assigned a unique identifier that can be
entered here as an additional means of identification.
Camera name
Assign a name to assist in identification. This name simplifies
the management of multiple devices in more extensive systems.
The name is used for remote identification, for example, in the
event of an alarm. Enter a name that makes it as easy as
possible to identify the location unambiguously.
Initiator extension
Add text to an initiator name to make identification easier in
large iSCSI systems. This text is added to the initiator name,
separated from it by a full stop.
9.2.2
Password
A password prevents unauthorized access to the device. The
device recognizes three authorization levels: service, user, and
live.
–
–
service is the highest authorization level. Entering the
correct password gives access to all the functions of the
camera and allows all configuration settings to be
changed.
user is the middle authorization level. This user can
operate the device, play back recordings, and also control
a camera but cannot change the configuration.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
56 en | Advanced Mode
Dinion2X IP Camera
–
live is the lowest authorization level. It can only be used to
view the live video image and switch between the different
live image displays.
Use the various authorization levels to limit access. Proper
password protection is only guaranteed if all higher
authorization levels are also protected with a password. For
example, if a live password is assigned, a service and a user
password should also be set. When assigning passwords,
always start from the highest authorization level, service, and
use different passwords.
Password
Define and change a separate password for each level while
logged in as service or if the device is not protected by a
password. Enter the password for the selected level.
Confirm password
Re-enter the new password to ensure that there are no typing
mistakes.
The new password is only saved after clicking Set. Therefore,
click Set immediately after entering and confirming the
password, even if assigning a password at another level.
9.2.3
Date/Time
Date format
Select the required date format.
Device date / Device time
If there are multiple devices operating in your system or
network, it is important to synchronize their internal clocks. For
example, it is only possible to identify and correctly evaluate
simultaneous recordings when all devices are operating on the
same time.
1. Enter the current date. Since the device time is controlled
by the internal clock, it is not necessary to enter the day of
the week – it is added automatically.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 57
2. Enter the current time or click Sync to PC to apply the
system time from your computer to the device.
Note:
It is important to ensure that the date/time is correct for
recording. An incorrect date/time setting could prevent correct
recording.
Device time zone
Select the time zone in which the system is located.
Daylight saving time
The internal clock can switch automatically between normal
and daylight saving time (DST). The device already contains the
data for DST switch-overs up to the year 2015. Use this data or
create alternative time saving data, if required.
Note:
If a table is not created, there is no automatic switching. When
editing the table, note that values occur in linked pairs (DST
start and end dates).
First, check the time zone setting. If it is not correct, select the
appropriate time zone for the system:
1. Click Set.
2. Click Details. A new window opens showing an empty
table.
3. Click Generate to fill the table with the preset values from
the camera.
4. Select the region or the city which is closest to the
system's location from the list box below the table.
5. Click one of the entries in the table to make changes. The
entry is highlighted.
6. Click Delete to remove the entry from the table.
7. Choose other values from the list boxes under the table, to
change the selected entry. Changes are immediate.
8. If there are empty lines at the bottom of the table, for
example after deletions, add new data by marking the row
and selecting values from the list boxes.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
58 en | Advanced Mode
Dinion2X IP Camera
9. When finished, click OK to save and activate the table.
Time server IP address
The camera can receive the time signal from a time server using
various time server protocols and then use it to set the internal
clock. The device polls the time signal automatically once every
minute. Enter the IP address of a time server.
Time server type
Select the protocol that is supported by the selected time
server. It is recommended to select the SNTP server protocol.
This protocol provides high accuracy and is required for special
applications and future function extensions. Select Time server
if the server uses the RFC 868 protocol.
9.2.4
Display Stamping
Various overlays or stamps in the video image provide
important supplementary information. These overlays can be
enabled individually and arranged on the image in a clear
manner.
Camera name stamping
This field sets the position of the camera name overlay. It can
be displayed at the Top, at the Bottom, or at a position of
choice using the Custom option, or it can be set to Off for no
overlay information.
If the Custom option is selected, enter values in the X and Y
position fields.
Time stamping
This field sets the position of the time and date overlay. It can
be displayed at the Top, at the Bottom, or at a position of
choice using the Custom option, or it can be set to Off for no
overlay information.
If the Custom option is selected, enter values in the X and Y
position fields.
Display milliseconds
If necessary, display milliseconds for Time stamping. This
information can be useful for recorded video images; however,
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 59
it does increase the processor's computing time. Select Off if
displaying milliseconds is not needed.
Alarm mode stamping
Select On for a text message to be overlaid in the event of an
alarm. It can be displayed at a position of choice using the
Custom option, or it can be set to Off for no overlay
information.
If the Custom option is selected, enter values in the X and Y
position fields.
Alarm message
Enter the message to be displayed on the image in the event of
an alarm. The maximum text length is 31 characters.
Video watermarking
Select On for the transmitted video images to be watermarked.
After activation, all images are marked with a green W. A red W
indicates that the sequence (live or saved) has been
manipulated.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
60 en | Advanced Mode
Dinion2X IP Camera
9.3
Web Interface
Web Interface
>
>
>
Appearance
LIVEPAGE Functions
Logging
9.3.1
Appearance
Adapt the appearance of the web interface and change the
website language to meet your requirements. If necessary,
replace the company's logo (top right) and the device name
(top left) in the top part of the window with individual graphics.
Either GIF or JPEG images can be used. The file paths must
correspond to the access mode (for example,
C:\Images\Logo.gif for access to local files or http://
www.myhostname.com/images/logo.gif for access via the
Internet/Intranet). For access via the Internet/Intranet, there
must be a connection in order to display the image. The image
files are not stored on the camera.
To restore the original graphics, delete the entries in the
Company logo and Device logo fields.
Website language
Select the language for the user interface here.
Company logo
Enter the path to a suitable image in this field. The image can
be stored on a local computer, a local network, or at an Internet
address.
Device logo
Enter the path for a suitable image for the device logo in this
field. The image can be stored on a local computer, a local
network, or at an Internet address.
JPEG interval
Specify the interval at which the individual images should be
generated for the M-JPEG image on the Livepage.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 61
9.3.2
LIVEPAGE Functions
In this window, adapt the Livepage functions to meet your
requirements. Choose from a variety of different options for
displaying information and controls.
1. Mark the check boxes for the functions to be displayed on
the Livepage. The selected elements are checked.
2. Check the Livepage to see how the desired items are
available.
Transmit audio
When selected, the audio from the camera (if on) is sent to the
computer.
Show alarm inputs
The alarm inputs are displayed next to the video image as icons
along with their assigned names. If an alarm is active, the
corresponding icon changes color.
Show relay outputs
The relay output is shown next to the video image as an icon
along with its assigned name. If a relay is switched, the icon
changes color.
Show VCA trajectories
The trajectories (motion lines of objects) from the video
content analysis are displayed in the live video image if a
corresponding analysis type is activated.
Show VCA metadata
When video content analysis (VCA) is activated, additional
information is displayed in the live video stream. For example,
in Motion+ mode, the sensor areas for motion detection are
marked.
Show event log
The event messages are displayed with the date and time in a
field next to the video image.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
62 en | Advanced Mode
Dinion2X IP Camera
Show system log
The system messages are displayed with the date and time in a
field next to the video image and provide information about the
establishment and termination of connections, etc.
Allow snapshots
Specify whether the icon for saving individual images should be
displayed below the live image. Individual images can only be
saved if this icon is visible.
Allow local recording
Specify whether the icon for saving video sequences on the
local memory should be displayed below the live image. Video
sequences can only be saved if this icon is visible.
Path for JPEG and video files
Enter the path for the storage location of individual images and
video sequences saved from the Livepage. If necessary, click
Browse to find a suitable folder.
9.3.3
Logging
Save event log
Select this option to save event messages in a text file on the
local computer. This file can be viewed, edited, and printed
with any text editor or standard office software.
File for event log
Enter the path for saving the event log here. If necessary, click
Browse to find a suitable folder.
Save system log
Select this option to save system messages in a text file on the
local computer. This file can be viewed, edited, and printed
with any text editor or standard office software.
File for system log
Enter the path for saving the system log here. If necessary, click
Browse to find a suitable folder.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 63
9.4
Encoder
Encoder
>
>
>
>
Privacy Masks
Encoder Profile
Encoder Streams
Audio
9.4.1
9.4.2
Privacy Masks
Four privacy mask areas can be defined. The activated masked
areas are filled with the selected pattern in live view.
1. Select the pattern to be used for all masks (Gray).
2. Check the box of the mask you wish to activate.
3. Use the mouse to define the area for each of the masks.
Encoder Profile
Adapt the video data transmission to the operating environment
(network structure, bandwidth, data structures). The camera
simultaneously generates two H.264 video streams and an
M-JPEG stream (Tri-streaming). Select the compression
settings of these streams individually, for example, one setting
for transmissions to the Internet and one for LAN connections.
The settings are made individually for each stream.
Define profiles
Eight definable profiles are available. The pre-programmed
profiles give priority to different parameters.
–
–
–
–
High resolution 1
High resolution (4CIF/D1) for high bandwidth connections
High resolution 2
High resolution (4CIF/D1) with lower data rate
Low bandwidth
High resolution (4CIF/D1) for low bandwidth connections
DSL
High resolution (4CIF/D1) for DSL connections at
500 kbps maximum
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
64 en | Advanced Mode
Dinion2X IP Camera
–
–
–
ISDN (2B)
CIF resolution for ISDN connections at 100 kbps maximum
ISDN (1B)
CIF resolution for ISDN connections at 50 kbps maximum
MODEM
CIF resolution for analog modem connections at 22 kbps
maximum
–
GSM
CIF resolution for GSM connections
Profile Configuration
Profiles can be configured for use with the H.264 settings of
encoder streams. Select a profile by clicking the appropriate
tab. Change the name of a profile and individual parameter
values within a profile.
Profiles are rather complex. They include a number of
parameters that interact with one another, so it is generally
best to use the default profiles. Only change a profile if
completely familiar with all the configuration options.
The parameters as a group constitute a profile and are
dependent on one another. If a setting outside the permitted
range for a parameter is entered, the nearest valid value is
substituted when the settings are saved.
Profile name
Enter a new name for the profile here.
Target data rate
To optimize utilization of the bandwidth in the network, limit
the data rate for the camera. The target data rate should be set
according to the desired picture quality for typical scenes with
no excessive motion.
For complex images or frequent changes of image content due
to frequent movements, this limit can temporarily be exceeded
up to the value entered in the Maximum data rate field.
Maximum data rate
This maximum data rate is not exceeded under any
circumstances. Depending on the video quality settings for the
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 65
I-frames and P-frames, this can result in individual images being
skipped.
The value entered here must be at least 10% higher than the
value entered in the Target data rate field. If the value entered
here is too low, it is automatically adjusted.
Encoding interval
The Encoding interval slider determines the interval at which
images are encoded and transmitted. This can be particularly
advantageous with low bandwidths. The image rate in ips
(images per second) is displayed next to the slider.
Video resolution
Select the desired resolution for the video image. The following
resolutions are available:
–
CIF
352 × 288/240 pixels
4CIF/D1
–
704 × 576/480 pixels
Expert Settings
if necessary, use the expert settings to adapt the I-frame quality
and the P-frame quality to specific requirements. The setting is
based on the H.264 quantization parameter (QP).
I-frame quality
This setting adjusts the image quality of the I-frames. The basic
setting Auto automatically adjusts the quality to the settings for
the P-frame video quality. Alternatively, use the slider to set a
value between 9 and 51. The value 9 represents the best image
quality with, if necessary, a lower frame refresh rate depending
on the settings for the maximum data rate. A value of 51 results
in a very high refresh rate and lower image quality.
P-frame quality
This setting adjusts the maximum image quality of the P-frames.
The basic setting Auto automatically adjusts to the optimum
combination of movement and image definition (focus).
Alternatively, use the slider to set a value between 9 and 51.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
66 en | Advanced Mode
Dinion2X IP Camera
The value 9 represents the best image quality with, if necessary,
a lower frame refresh rate depending on the settings for the
maximum data rate. A value of 51 results in a very high refresh
rate and lower image quality.
Default
Click Default to return the profile to the factory default values.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 67
9.4.3
Encoder Streams
Select H.264 Settings
1. Select the codec algorithm for streams 1 and 2. The
following algorithms are available
–
–
H.264 BP+ (HW decoder)
H.264 MP Low Latency
2. Select the default profile for streams 1 and 2 from the
eight profiles that have been defined.
The algorithm properties have the following settings:
H.264 BP+
H.264 MP
(HW decoder)
Low Latency
CABAC
off
on
IP
on
off
IP
CAVLC
GOP structure
I-frame distance
Deblocking filter
15
on
30
on
Recommended for Hardware
decoders,
Software decoders,
PTZ and rapid
Divar 700 Series
image movements
Preview >>
Previews of streams 1 and 2 can be shown.
1. Click Preview >> to display a preview of the video for
streams 1 and 2. the current profile is shown above the
preview.
2. Click 1:1 Live View below a preview to open a viewing
window for that stream. Various additional items of
information are shown across the top of the window.
3. Click Preview << to close the preview displays.
Note:
Deactivate the display of the video images if the performance of
the computer is adversely affected by the decoding of the data
stream.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
68 en | Advanced Mode
Dinion2X IP Camera
JPEG stream
Set the parmeters for the M-JPEG stream.
–
–
Select the Max. frame rate in images per second (IPS).
The Picture quality slider allows adjustment of the
M-JPEG image quality from Low to High.
Note:
The JPEG resolution follows the highest resolution setting
either in stream 1 or stream 2. For example, if stream 1 is 4CIF/
D1 and stream 2 is CIF, the JPEG resolution will be 4CIF/D1.
9.5
Audio
Switch the camera audio On or Off. Adjust the input and output
levels with the sliders.
Note:
The audio signals are sent in a separate data stream parallel to
the video data, and so increase the network load. The audio
data requires an additional bandwidth of approximately
80 kbps for each connection. If you do not want any audio data
to be transmitted, select Off.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 69
9.6
Camera
Camera
>
>
>
>
>
>
>
Mode
ALC
Shutter/AGC
Day/night
Enhance
Color
Installer Options
If the camera is in monochrome mode, all color-related menu
items are disabled and cannot be accessed.
9.6.1
Mode
Pre-defined modes
The camera has six pre-programmed operating modes that can
be selected in the Mode menu.
The modes are defined as follows:
1. 24-hour
Default installation mode to provide stable pictures over a
24-hour period. These settings are optimized for out-of-
the-box installation.
2. Traffic
Capture high-speed objects using default shutter in
variable lighting conditions.
3. Low light
Provide extra enhancement, such as AGC and SensUp to
make usable pictures in low-light conditions.
4. Smart BLC
Settings optimized to capture details in high contrast and
extremely bright-dark conditions.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
70 en | Advanced Mode
Dinion2X IP Camera
5. Low noise
Enhancements are set to reduce picture noise. Useful for
conditional refresh DVR and IP storage systems because
reducing noise reduces the amount of storage required.
6. Infrared
Use this mode if the camera is viewing a scene lit by
infrared light.
These modes are pre-programmed by default but can be
adjusted according to personal preferences. The Mode menu
allows selection and set-up of picture enhancement functions
for each mode. If the changes are not satisfactory, restore the
default values for the mode.
Mode ID
Enter a name for the selected mode.
Copy mode to
Select a mode to copy the current mode to.
Restore Mode Defaults
Click to restore the factory defaults. A confirmation screen
appears. Allow 5 seconds for the camera to optimize the
picture after a mode reset.
9.6.2
ALC
ALC level
Adjust the video output level (-15 to 0 to +15).
Select the range within which the ALC will operate. A positive
value is more useful for low-light conditions; a negative value is
more useful for very bright conditions.
Some ALC adjustment may improve scene content when Smart/
BLC is enabled.
Peak average
Adjust the balance between peak and average video control
(-15 to 0 to +15). At -15 the camera controls the average video
level, at +15 the camera controls the peak video level.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 71
A negative value gives more priority to average light levels; a
positive value gives more priority to peak light levels. Video iris
lens: choose an average level for best results (peak settings
may cause oscillations).
Speed
Adjust the speed of the video level control loop (Slow, Medium,
or Fast). For most scenes it should remain at the default value.
9.6.3
Shutter/AGC
Shutter
–
–
Fixed — allows a user-defined shutter speed.
AES (auto-shutter) — the camera automatically sets the
optimum shutter speed. The camera tries to maintain the
selected default shutter speed as long as the light level of
the scene permits.
–
FL — flickerless mode avoids interference from light
sources (recommended for use with video iris or DC iris
lenses only).
Default shutter / Fixed shutter
Select the shutter speed (1/60 [1/50], 1/100, 1/120, 1/250, 1/
500, 1/1000, 1/2000, 1/5000, 1/10K) for the default (AES) or
fixed value.
In AES mode, the camera tries to maintain the selected shutter
speed as long as the light level of the scene is high enough.
In Fixed mode, select the shutter speed.
Actual shutter
Displays the actual shutter value from the camera to help
compare lighting levels and optimum shutter speed during set-
up.
Sensitivity up
Selects the factor by which the sensitivity of the camera is
increased (OFF, 2x, 3x, etc. to a maximum of 10x).
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
72 en | Advanced Mode
Dinion2X IP Camera
Note:
If Sensitivity up is active, some noise or spots may appear in the
picture. This is normal camera behavior. Sensitivity up may
cause some motion blur on moving objects.
Gain
AGC - the camera automatically sets the gain to the lowest
possible value needed to maintain a good picture.
Fixed - sets Fixed gain value.
Maximum gain / Fixed gain
Selects the maximum value the gain can have during AGC
operation (0 to 30 dB).
Selects the gain setting for Fixed gain operation (0 is no gain).
Actual gain
Displays the actual AGC value from the camera to help compare
gain level with lighting levels and picture performance.
9.6.4
Day/night
The Day/Night camera is equipped with a motorized IR
(infrared) filter. The IR filter can be removed in low-light or IR-
illuminated applications. There are four different methods of
switching:
–
–
–
–
via the alarm input,
as part of the programmable mode profile,
automatically, based on the observed light levels, or
via the settings page.
Day/night
Auto - the camera switches the IR cut-off filter on and off
depending on the scene illumination level.
Monochrome - the IR cut-off filter is removed, giving full IR
sensitivity.
Color - the camera always produces a color signal regardless of
light levels.
Switch level
Set the video Switch level at which the camera in Auto mode
switches to monochrome operation (-15 to 0 to +15).
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 73
A low (negative) value means that the camera switches to
monochrome at a lower light level. A high (positive) value
means that the camera switches to monochrome at a higher
light level.
Priority
In Auto switching mode, set the camera priority to either:
–
–
Color: the camera gives color pictures as long as the light
level permits.
Motion: the camera gives sharp images without motion
blur as long as the light level permits (it switches to
monochrome earlier than it would with Color priority).
The camera recognizes IR-illuminated scenes to prevent
unwanted switching to color mode.
IR contrast
There are two modes for IR contrast:
–
Enhanced: the camera optimizes contrast in applications
with high IR illumination levels. Select this mode for IR
(730 to 940 nm) light sources and for scenes with grass
and green foliage.
–
Normal: the camera optimizes contrast in mono
applications with visible light illumination.
Color burst
–
Off: the color burst in the video signal is switched Off in
monochrome mode.
–
On: the color burst remains active even in monochrome
mode (required by some DVRs and IP encoders).
9.6.5
Enhance
Dynamic engine
–
–
–
Off: turns off all automatic scene detail and enhancements
(only recommendedfor testing).
XF Dynamic: extra internal processing is enabled for low-
light applications (traffic, etc.).
2X Dynamic: 2X Dynamic adds dual sensor exposure to the
XF Dynamic features. In harsh lighting conditions pixels
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
74 en | Advanced Mode
Dinion2X IP Camera
from each exposure are mixed to give a more detailed
image (use 2X Dynamic when SmartBLC is not required).
Smart BLC: BLC window and weighting factor are
automatically defined. Camera dynamically adjusts these
for changing light conditions. Includes all the benefits of
2X Dynamic.
–
Auto black
Auto black ON automatically increases the visibility of details
even when scene contrast is less than full-range due to mist,
fog, etc.
Sharpness level
Adjusts the black level between -15 and +15. Zero position of
slider corresponds to the factory default black level.
A low (negative) value makes the picture less sharp. Increasing
sharpness brings out more detail. Extra sharpness can enhance
the details of license plates, facial features and the edges of
certain surfaces.
Dynamic noise reduction
In AUTO mode the camera automatically reduces the noise in
the picture. This may cause some motion blur on exceptionally
fast moving objects immediately in front of the camera. This can
be corrected by widening the field of view or selecting Off.
Peak white invert
Use Peak white invert to reduce glare from the CRT/LCD
display.
Use in ANPR/LPR applications to reduce headlight glare. (Test
on-site to ensure that it does benefit the application and is not
distracting for operators.)
9.6.6
Color
White balance
–
ATW: Auto tracking white balance allows the camera to
continually adjust for optimal color reproduction.
–
AWB hold: Puts ATW on hold and saves the color settings.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
–
Advanced Mode | en 75
In Manual mode the Red, Green, and Blue gain can be
manually set to a desired position.
Speed
Adjust the speed (Fast, Mediumor Slow) of the white balance
control loop.
R-gain
Offsets factory white point alignment (reducing red introduces
more cyan).
ATW and AWBhold (-5 to +5): adjusts the Red gain to optimize
the white point.
Manual (-50 to +50): adjusts the Red gain.
B-gain
Offsets factory white point alignment (reducing blue introduces
more yellow).
ATW and AWBhold (-5 to +5): adjusts the B gain to optimize the
white point.
Manual (-50 to +50): adjusts the Blue gain.
G-gain
Manual (-50 to +50): adjusts the Green gain.
It is only necessary to change the white point offset for special
scene conditions.
Saturation
Adjusts the color saturation; -15 gives a monochrome image.
9.6.7
Installer Options
Synchronization
Select the Synchronization method for the camera:
–
–
Line lock to lock to the power supply frequency;
Internal for free running camera operation.
Ticker bar
Switches a ticker bar on the live image on or off.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
76 en | Advanced Mode
Dinion2X IP Camera
Camera buttons
Disable the Camera buttons on the camera to prevent
unauthorized change of the camera settings.
Camera LED
Disable the Camera LED on the camera to switch it off.
Show test pattern
Select On to show a video test signal.
Pattern
Select the desired test pattern to help with installation and
fault-finding.
Restore all defaults
Click Restore all defaults to restore the factory defaults for the
camera. A confirmation screen appears. Allow 5 seconds for the
camera to optimize the picture after a mode reset.
Note:
The default IP address is restored. Connect to the camera again
using this address.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 77
9.7
Recording
Recording
>
>
>
>
>
Storage Management
Recording Profiles
Retention Time
Recording Scheduler
Recording Status
Record the images from the camera to an appropriately
configured iSCSI system. For long-term authoritative images
use an appropriately sized iSCSI system.
A Video Recording Manager (VRM) can control all recording
when accessing an iSCSI system. The VRM is an external
program for configuring recording tasks for video servers. For
further information, contact your local customer service at
Bosch Security Systems.
9.7.1
Storage Management
Device manager
If the VRM option is activated, the VRM Video Recording
Manager manages all recording and no further settings can be
configured here.
Note:
Activating or deactivating VRM causes the current settings to be
lost; they can only be restored through reconfiguration.
Recording media
Select the required recording media to activate them and then
configure the recording parameters.
iSCSI Media
If an iSCSI system is selected as the storage medium, a
connection to the desired iSCSI system is needed to set the
configuration parameters.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
78 en | Advanced Mode
Dinion2X IP Camera
The storage system selected must be available on the network
and completely set up. Amongst other things, it must have an IP
address and be divided into logical drives (LUN).
1. Enter the IP address of the required iSCSI destination in
the iSCSI IP address field.
2. If the iSCSI destination is password protected, enter this
into the Password field.
3. Click the Read button. The connection to the IP address is
established. The Storage overview field displays the
logical drives.
Activating and Configuring Storage Media
The storage overview displays the available storage media.
Select individual media or iSCSI drives and transfer these to the
Managed storage media list. Activate the storage media in this
list and configure them for storage.
Note:
Each storage medium can only be associated with one user. If a
storage medium is already being used by another user,
decouple the user and connect the drive to the camera. Before
decoupling, make absolutely sure that the previous user no
longer needs the storage medium.
1. In the Storage overview section, double-click the required
storage medium, an iSCSI LUN or one of the other
available drives. The medium is then added to the
Managed storage media list. Newly added media is
indicated in the Status column by the status Not active.
2. Click Set to activate all media in the Managed storage
media list. These are indicated in the Status column by the
status Online.
3. Check the box in the Rec. 1 or Rec. 2 column to specify
which data stream should be recorded on the storage
media selected. Rec. 1 stores stream 1, Rec. 2 stores
stream 2.
4. Check the boxes for the Overwrite older recordings
option to specify which older recordings can be
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 79
overwritten once the available memory capacity has been
used. Recording 1 corresponds to stream 1, Recording 2
corresponds to stream 2.
Note:
If older recordings are not allowed to be overwritten when the
available memory capacity has been used, the recording in
question is stopped. Specify limitations for overwriting old
recordings by configuring the retention time.
Formatting Storage Media
Delete all recordings on a storage medium at any time. Check
the recordings before deleting and back up important
sequences on the computer's hard drive.
1. Click a storage medium in the Managed storage media list
to select it.
2. Click Edit below the list. A new window opens.
3. Click Formatting to delete all recordings in the storage
medium.
4. Click OK to close the window.
Deactivating Storage Media
Deactivate any storage medium from the Managed storage
media list. It is then no longer used for recordings.
1. Click a storage medium in the Managed storage media list
to select it.
2. Click Remove below the list. The storage medium is
deactivated and removed from the list.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
80 en | Advanced Mode
Dinion2X IP Camera
9.7.2
Recording Profiles
Define up to ten different recording profiles here, then assign
these to individual days or times of day on the Recording
Scheduler page. Modify the names of the recording profiles on
the tabs in the Recording Scheduler page.
1. Click a tab to edit the corresponding profile.
2. If necessary, click Default to return all settings to their
defaults.
3. Click Copy Settings to copy the currently visible settings
to other profiles. A window opens to select the target
profiles for the copied settings.
4. For each profile, click Set to save.
Stream profile settings
Select the profile setting that is to be used for each data stream
when recording. This selection is independent of the selection
for live data stream transmission. (The properties of the
profiles are defined on the Encoder Profile page.)
Recording includes
Specify whether, in addition to video data, audio or metadata
(for example alarms or VCA data) should also be recorded.
Including metadata could make subsequent searches of
recordings easier but it requires additional memory capacity.
Without metadata, it is not possible to include video content
analysis in recordings.
Standard recording
Select the mode for standard recordings:
–
Continuous: the recording proceeds continuously. If the
maximum memory capacity is reached, older recordings
will automatically be overwritten.
–
–
Pre-alarm: recording takes place in the pre-alarm time,
during the alarm and during the post-alarm time only.
Off: no automatic recording takes place.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 81
Stream
Select the data stream to be used for standard recordings. (You
can select the data stream for alarm recordings separately and
independently of this setting.)
Alarm recording
Select the Pre-alarm time from the list box.
Select the Post-alarm time from the list box.
Select the Alarm stream to use for alarm recording. The
encoding interval for alarm recording can be selected from the
predefined profiles.
Alarm triggers
Select the alarm type (Alarm input/ Motion/Audio alarm /
Video loss alarm) that is to trigger a recording. Select the
Virtual alarm sensors that are to trigger a recording, via RCP+
commands or alarm scripts, for example.
9.7.3
Retention Time
Specify the retention times for recordings. If the available
memory capacity of a medium has been used, older recordings
are only overwritten if the retention time entered here has
expired.
Make sure that the retention time corresponds with the
available memory capacity. A rule of thumb for the memory
requirement is as follows: 1 GB per hour retention time with
4CIF for complete frame rate and high image quality.
Enter the required retention time in hours or days for each
recording. Recording 1 corresponds to Stream 1, Recording 2
corresponds to Stream 2.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
82 en | Advanced Mode
Dinion2X IP Camera
9.7.4
Recording Scheduler
The recording scheduler allows you to link the created
recording profiles to the days and times at which the camera's
images are to be recorded in the event of an alarm. Schedules
can be defined for weekdays and for holidays.
Weekdays
Assign as many time periods (in 15-minute intervals) as needed
for any day of the week. Move the mouse cursor over the table —
the time is displayed.
1. Click the profile to be assigned in the Time periods box.
2. Click a field in the table and, while holding down the left
mouse button, drag the cursor across all of the fields to be
assigned to the selected profile.
3. Use the right mouse button to deselect any of the intervals.
4. Click Select All to select all of the intervals to be assigned
to the selected profile.
5. Click Clear All to deselect all of the intervals.
6. When finished, click Set to save the settings to the device.
Holidays
Define holidays whose settings will override the settings for the
normal weekly schedule.
1. Click the Holidays tab. Days that have already been
defined are shown in the table.
2. Click Add. A new window opens.
3. Select the desired date from the calendar. Drag the mouse
to select a range of dates. These are handled as a single
entry in the table.
4. Click OK to accept the selection(s). The window closes.
5. Assign the defined holidays to the recording profile as
described above.
Delete user-defined holidays at any time.
1. Click Delete in the Holidays tab. A new window opens.
2. Click the date to be deleted.
3. Click OK. The selection is removed from the table and the
window is closed.
4. Repeat for any other dates to be deleted.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 83
Profile names
Change the names of the recording profiles listed in the Time
periods box.
1. Click a profile.
2. Click Rename.
3. Enter the new name and click Rename again.
Activate recording
After completing configuration, activate the recording schedule
and start recording. Once activated, the Recording Profiles and
the Recording Scheduler are deactivated and the configuration
cannot be modified. Terminate recording at any time to modify
the configuration.
1. Click Start to activate the recording schedule.
2. Click Stop to deactivate the recording schedule.
Recordings that are currently running are interrupted and
the configuration can be modified.
Recording status
The graphic indicates the recording activity. An animated
graphic is seen when recording is taking place.
9.7.5
Recording Status
Details of the recording status are displayed here for
information. These settings cannot be changed.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
84 en | Advanced Mode
Dinion2X IP Camera
9.8
Alarm
Alarm
>
>
>
>
>
Alarm Connections
VCA
Audio Alarm
Alarm E-Mail
Alarm Task Editor
9.8.1
Alarm Connections
Select the response of the camera when an alarm occurs. In the
event of an alarm, the device can automatically connect to a
pre-defined IP address. The device can contact up to ten IP
addresses in the order listed until a connection is established.
Connect on alarm
Select On so that the camera automatically connects to a pre-
defined IP address in the event of an alarm. Select Follows
input 1 so that the device maintains the connection for as long
as an alarm exists.
Number of destination IP address
Specify the numbers of the IP addresses to be contacted in the
event of an alarm. The device contacts the remote locations one
after the other in the numbered sequence until a connection is
made.
Destination IP address
For each number, enter the corresponding IP address for the
desired remote station.
Destination password
If the remote station is password protected, enter the
password here.
Only ten passwords can be defined here. Define a general
password if more than ten connections are required, for
example, when connections are initiated by a controlling
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 85
system such as VIDOS or Bosch Video Management System.
The camera connects to all remote stations protected by the
same general password. To define a general password:
1. Select 10 in the Number of destination IP address list
box.
2. Enter 0.0.0.0 in the Destination IP address field.
3. Enter the password in the Destination password field.
4. Set the user password of all the remote stations to be
accessed using this password.
Setting destination 10 to the IP-address 0.0.0.0 overrides its
function as the tenth address to try.
Video transmission
If the device is operated behind a firewall, select TCP (HTTP
port) as the transfer protocol. For use in a local network, select
UDP.
Please note that in some circumstances, in the event of an
alarm, a larger bandwidth must be available on the network for
additional video images (if Multicast operation is not possible).
To enable Multicast operation, select the UDP option for the
Video transmission parameter here and on the Network page.
Remote port
Select a browser port, depending on the network configuration.
The ports for HTTPS connections are only available if the On
option in SSL encryption is selected.
Video output
If it is known which device is being used as the receiver, select
the analog video output to which the signal should be switched.
If the destination device is unknown, it is advisable to select the
First available option. In this case, the image is placed on the
first free video output. This is an output on which there is no
signal. The connected monitor only displays images when an
alarm is triggered. If a particular video output is selected and a
split image is set for this output on the receiver, select the
decoder from Decoder in the receiver that is to be used to
display the alarm image. Refer to the destination device
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
86 en | Advanced Mode
Dinion2X IP Camera
documentation concerning image display options and available
video outputs.
Decoder
Select a decoder of the receiver to display the alarm image. The
decoder selected has an impact on the position of the image in
a split screen.
SSL encryption
SSL encryption protects data used for establishing a
connection, such as the password. By selecting On, only
encrypted ports are available for the Remote port parameter.
SSL encryption must be activated and configured on both sides
of a connection. The appropriate certificates must also have
been uploaded. Configure and activate encryption for media
data (video, metadata) on the Encryption page.
Auto-connect
Select On to automatically re-established a connection to one
of the previously specified IP addresses after each reboot,
connection breakdown, or network failure.
Audio
Select On to transmit the audio stream with an alarm
connection.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 87
9.8.2
Video Content Analyses (VCA)
The camera has integrated VCA which can detect and analyze
changes in the signal using image processing algorithms. Such
changes can be due to movements in the camera's field of view.
Select various VCA configurations and adapt these to your
application, as required. The Silent MOTION+ configuration is
active by default. In this configuration, metadata is created to
facilitate searches of recordings, however, no alarm is
triggered.
1. Select a VCA configuration and make the required settings.
2. If necessary, click the Default button to return all settings
to their default values.
Note:
If there is not enough computing power, priority is given to live
images and recordings. This can lead to impairment of the VCA
system. Observe the processor load and optimize the encoder
settings or the VCA settings if necessary, or turn off VCA
completely.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
88 en | Advanced Mode
Dinion2X IP Camera
9.8.3
VCA configuration- Profiles
Configure two profiles with different VCA configurations. Save
profiles on your computer's hard drive and load saved profiles
from there. This can be useful if testing a number of different
configurations. Save a functioning configuration and test new
settings. Use the saved configuration to restore the original
settings at any time.
1. Select a VCA profile and enter the required settings.
2. If necessary, click Default to return all settings to default
values.
3. Click the Save... to save the profile settings to another file.
A new window opens in which to specify the file name and
where to save it.
4. Click Load... to load a saved profile. A new window opens
in which to select the profile file and specify where to save
the file.
To rename a profile:
1. To rename the file, click the icon to the right of the list field
and enter the new profile name in the field.
2. Click the icon again. The new profile name is saved.
The current alarm status is displayed for information purposes.
Aggregation time (s)
Set an aggregation time of between 0 and 20 seconds. The
aggregation time always starts when an alarm event occurs. It
extends the alarm event by the value set. This prevents alarm
events that occur in quick succession from triggering several
alarms and successive events in a rapid sequence. No further
alarm is triggered during the aggregation time.
The post-alarm time set for alarm recordings only starts once
the aggregation time has expired.
Analysis type
Select the required analysis algorithm. By default, only Motion+
is available — this offers a motion detector and essential
recognition of tampering.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 89
Metadata is always created for a video content analysis, unless
this was explicitly excluded. Depending on the analysis type
selected and the relevant configuration, additional information
overlays the video image in the preview window next to the
parameter settings. With the Motion+ analysis type, for
example, the sensor fields in which motion is recorded are
marked with rectangles.
Note:
Additional analysis algorithms with comprehensive functions,
such as IVMD and IVA, are available from Bosch Security
Systems.
Motion detector
Motion detection is available for the Motion+ analysis type. For
the detector to function, the following conditions must be met:
–
–
–
Analysis must be activated.
At least one sensor field must be activated.
The individual parameters must be configured to suit the
operating environment and the desired responses.
The sensitivity must be set to a value greater than zero.
–
Note:
Reflections of light (from glass surfaces, etc.), lights switching
on and off, or changes in the light level caused by cloud
movement on a sunny day can trigger unintended responses
from the motion detector and generate false alarms. Run a
series of tests at different times of the day and night to ensure
that the video sensor is operating as intended. For indoor
surveillance, ensure constant lighting of the areas during the
day and at night.
Sensitivity
Sensitivity is available for the Motion+ analysis type. The basic
sensitivity of the motion detector can be adjusted for the
environmental conditions to which the camera is subject. The
sensor reacts to variations in the brightness of the video image.
The darker the observation area, the higher the value that must
be selected.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
90 en | Advanced Mode
Dinion2X IP Camera
Minimum object size
Specify the number of sensor fields that a moving object must
cover to generate an alarm. This setting prevents objects that
are too small from triggering an alarm. A minimum value of 4 is
recommended. This value corresponds to four sensor fields.
Debounce time 1 s
The debounce time prevents very brief alarm events from
triggering individual alarms. If the Debounce time 1 s option is
activated, an alarm event must last at least 1 second to trigger
an alarm.
Selecting the area
Select the areas of the image to be monitored by the motion
detector. The video image is subdivided into square sensor
fields. Activate or deactivate each of these fields individually. To
exclude particular regions of the camera's field of view from
monitoring due to continuous movement (by a tree in the wind,
for example), the relevant fields can be deactivated.
1. Click Select Area to configure the sensor fields. A new
window opens.
2. If necessary, click Clear All first to clear the current
selection (fields marked red).
3. Left-click the fields to be activated. Activated fields are
marked red.
4. If necessary, click Select All to select the entire video-
frame for monitoring.
5. Right-click any fields to deactivate.
6. Click OK to save the configuration.
7. Click the close button (X) in the window title bar to close
the window without saving the changes.
Tamper detection
Detect tampering of cameras and video cables by means of
various options. Run a series of tests at different times of the
day and night to ensure that the video sensor is operating as
intended.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 91
Sensitivity and Trigger delay (s) can only be changed if
Reference check is selected.
Sensitivity
The basic sensitivity of the tamper detection can be adjusted
for the environmental conditions to which the camera is
subject. The algorithm reacts to the differences between the
reference image and the current video image. The darker the
observation area, the higher the value that must be selected.
Trigger delay (s)
Set delayed alarm triggering here. The alarm is only triggered
after a set time interval in seconds has elapsed and then only if
the triggering condition still exists. If the original condition has
been restored before this time interval elapses, the alarm is not
triggered. This avoids false alarms triggered by short-term
changes, for example, cleaning activities in the direct field of
vision of the camera.
Global change (slider)
Set how large the global change in the video image must be for
an alarm to be triggered. This setting is independent of the
sensor fields selected under Select Area. Set a high value if
fewer sensor fields need to change to trigger an alarm. With a
low value, it is necessary for changes to occur simultaneously in
a large number of sensor fields to trigger an alarm. This option
allows detection, independently of motion alarms, manipulation
of the orientation or location of a camera resulting from turning
the camera mount bracket, for example.
Global change
Activate this function if the global change, as set with the
Global change slide control, should trigger an alarm.
Scene too bright
Activate this function if tampering associated with exposure to
extreme light (for instance, shining a flashlight directly on the
objective) should trigger an alarm. The average brightness of
the scene provides a basis for recognition.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
92 en | Advanced Mode
Dinion2X IP Camera
Scene too dark
Activate this function if tampering associated with covering the
objective (for instance, by spraying paint on it) should trigger
an alarm. The average brightness of the scene provides a basis
for recognition.
Scene too noisy
Activate this function if tampering associated with EMC
interference (noisy scene as the result of a strong interference
signal in the vicinity of the video lines) should trigger an alarm.
Reference check
Save a reference image that can be continuously compared with
the current video image. If the current video image in the
marked areas differs from the reference image, an alarm is
triggered. This detects tampering that would otherwise not be
detected, for example, if the camera is turned.
1. Click Reference to save the currently visible video- image
as a reference.
2. Click Select Area and select the areas in the reference
image that are to be monitored.
3. Check the box Reference check to activate the on-going
check. The stored reference image is displayed in black
and white below the current video image, and the selected
areas are marked in yellow.
4. Select the Disappearing edges or Appearing edges option
to specify the reference check once again.
Disappearing edges
The area selected in the reference image should contain a
prominent structure. If this structure is concealed or moved,
the reference check triggers an alarm. If the selected area is too
homogenous, so that concealing and moving the structure
would not trigger an alarm, then an alarm is triggered
immediately to indicate the inadequate reference image.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 93
Appearing edges
Select this option if the selected area of the reference image
includes a largely homogenous surface. If structures appear in
this area, then an alarm is triggered.
Selecting the area
Select the image areas in the reference image that are to be
monitored. The video image is subdivided into square fields.
Activate or deactivate each of these fields individually.
Select only those areas for reference monitoring in which no
movement takes place and that are always evenly lit, as false
alarms could otherwise be triggered.
1. Click Select Area to configure the sensor fields. A new
window opens.
2. If necessary, click Clear All first to clear the current
selection (fields marked yellow).
3. Left-click the fields to be activated. Activated fields are
marked yellow.
4. If necessary, click Select All to select the entire video-
frame for monitoring.
5. Right-click any fields to deactivate.
6. Click OK to save the configuration.
7. Click the close button (X) in the window title bar to close
the window without saving the changes.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
94 en | Advanced Mode
Dinion2X IP Camera
9.8.4
VCA configuration - Scheduled
A scheduled configuration allows you to link a VCA profile with
the days and times at which the video content analysis is to be
active. Schedules can be defined for weekdays and for holidays.
Weekdays
Link any number of 15-minute intervals with the VCA profiles for
each day of the week. Moving the mouse cursor over the table
displays the time below it. This aids orientation.
1. Click the profile to link in the Time periods field.
2. Click in a field in the table, hold down the mouse button
and drag the cursor over all the periods to be assigned to
the selected profile.
3. Use the right mouse button to deselect any of the intervals.
4. Click Select All to link all time intervals to the selected
profile.
5. Click Clear All to deselect all of the intervals.
6. When finished, click Set to save the settings in the device.
Holidays
Define holidays on which a profile should be active that are
different to the standard weekly schedule.
1. Click the Holidays tab. Any days that have already been
selected are shown in the table.
2. Click Add. A new window opens.
3. Select the desired date from the calendar. Select several
consecutive calendar days by holding down the mouse
button. These will later be displayed as a single entry in the
table.
4. Click OK to accept the selection. The window closes.
5. Assign the individual holidays to the VCA profiles, as
described above.
Deleting Holidays
Delete defined holidays at any time:
1. Click Delete. A new window opens.
2. Click the date to delete.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 95
3. Click OK. The item is deleted from the table and the
window closes.
4. The process must be repeated for deleting additional days.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
96 en | Advanced Mode
Dinion2X IP Camera
9.8.5
VCA configuration - Event triggered
This configuration allows you to stipulate that the video content
analysis is only to be activated when triggered by an event. As
long as no trigger is activated, the Silent MOTION+
configuration in which metadata is created is active; this
metadata facilitates searches of recordings, but does not
trigger an alarm.
Trigger
Select a physical alarm or a virtual alarm as a trigger. A virtual
alarm is created using software, with RCP+ commands or alarm
scripts, for example.
Trigger active
Select the VCA configuration here that is to be enabled via an
active trigger. A green check mark to the right of the list field
indicates that the trigger is active.
Trigger inactive
Select the VCA configuration here that is to be activated if the
trigger is not active. A green check mark to the right of the list
field indicates that the trigger is inactive.
Delay (s)
Select the delay period for the reaction of the video content
analysis to trigger signals. The alarm is only triggered after a set
time interval in seconds has elapsed and then only if the
triggering condition still exists. If the original condition has
been restored before this time interval elapses, the alarm is not
triggered. A delay period may be useful in avoiding false alarms
or frequent triggering. During the delay period, the Silent
MOTION+ configuration is always enabled.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 97
9.8.6
Audio Alarm
Create alarms based on audio signals. Configure signal
strengths and frequency ranges so that false alarms, for
example, machine noise or background noise, are avoided.
Set up normal audio transmission before configuring the audio
alarm.
Audio alarm
Select On for the device to generate audio alarms.
Name
The name makes it easier to identify the alarm in extensive
video monitoring systems, for example with the VIDOS and
Bosch Video Management System programs. Enter a unique and
clear name here.
Signal Ranges
Exclude particular signal ranges in order to avoid false alarms.
For this reason the total signal is divided into 13 tonal ranges
(mel scale). Check or uncheck the boxes below the graphic to
include or exclude individual ranges.
Threshold
Set up the threshold on the basis of the signal visible in the
graphic Set the threshold using the slide control or,
alternatively, move the white line directly in the graphic using
the mouse.
Sensitivity
Use this setting to adapt the sensitivity to the sound
environment and effectively suppress individual signal peaks. A
high value represents a high level of sensitivity.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
98 en | Advanced Mode
Dinion2X IP Camera
9.8.7
Alarm E-Mail
As an alternative to automatic connecting, alarm states can also
be documented by e-mail. This makes it possible to notify a
recipient who does not have a video receiver. In this case, the
camera automatically sends an e-mail to a user-defined e-mail
address.
Send alarm e-mail
Select On for the device to automatically send an alarm e-mail
in the event of an alarm.
Mail server IP address
Enter the IP address of a mail server that operates on the SMTP
standard (Simple Mail Transfer Protocol). Outgoing e-mails are
sent to the mail server via the address entered. Otherwise,
leave the box blank (0.0.0.0).
SMTP user name
Enter a registered user name for the chosen mail server.
SMTP password
Enter the required password for the registered user name.
Format
Select the data format of the alarm message.
–
–
Standard (with JPEG): e-mail with JPEG image file
attachment.
SMS: e-mail in SMS format to an e-mail-to-SMS gateway
(for example, to send an alarm by cellphone) without an
image attachment.
When a cellphone is used as the receiver, make sure to activate
the e-mail or SMS function, depending on the format, so that
these messages can be received. Obtain information on
operating your cellphone from your cellphone provider.
Attach JPEG from camera
Check the box to specify that JPEG images are sent from the
camera.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 99
Destination address
Enter the e-mail address for alarm e-mails here. The maximum
address length is 49 characters.
Sender name
Enter a unique name for the e-mail sender, for example, the
location of the device. This makes it easier to identify the origin
of the e-mail.
Test e-mail
Click Send Now to test the e-mail function. An alarm e-mail is
immediately created and sent.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
100 en | Advanced Mode
Dinion2X IP Camera
9.8.8
Alarm Task Editor
Editing scripts on this page overwrites all settings and entries
on the other alarm pages. This procedure cannot be reversed.
To edit this page, you should have programming knowledge and
be familiar with the information in the Alarm Task Script
Language document and the English language. The document
can be found on the product DVD supplied.
As an alternative to the alarm settings on the various alarm
pages, enter the desired alarm functions in script form here.
This will overwrite all settings and entries on the other alarm
pages.
1. Click Examples under the Alarm Task Editor field to see
some script examples. A new window opens.
2. Enter new scripts in the Alarm Task Editor field or change
existing scripts in line with your requirements.
3. When finished, click Set to transmit the scripts to the
device. If the transfer was successful, the message Script
successfully parsed. is displayed over the text field. If it
was not successful, an error message is displayed with
further information.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 101
9.9
Interfaces
Interfaces
>
>
>
Alarm input
Relay
COM1
9.9.1
Alarm input
Configure the alarm triggers for the camera.
Select N.C. (Normally Closed) if the alarm is to be triggered by
closing the contact.
Select N.O. (Normally Open) if the alarm is to be triggered by
opening the contact.
Name
Enter a name for the alarm input. This is then displayed below
the icon for the alarm input on the LIVEPAGE (if configured).
Action
Select the camera mode to switch to when alarm input 1 is
triggered. See Section 9.8.8 Alarm Task Editor, page 100, for
information on alarm actions based on alarm inputs.
9.9.2
Relay
Configure the switching behavior of the relay output.
Select different events that automatically activate an output.
For example, turn on a floodlight by triggering a motion alarm
and then turn the light off again when the alarm has stopped.
Idle state
Select Open for the relay to operate as an N.O. contact, or
select Closed if the relay is to operate as an N.C. contact.
Select
Select External device or Motion+/IVA to trigger the relay.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
102 en | Advanced Mode
Dinion2X IP Camera
Relay name
The relay can be assigned a name here. The name is shown on
the button next to Trigger relay. The LIVEPAGE can also be
configured to display the name next to the relay icon.
Trigger relay
Click the button to switch the relay manually (for example, for
testing purposes or to operate a door opener).
9.9.3
COM1
Configure the data connector for the camera.
Serial port function
Select a controllable unit from the list. If you wish to use the
serial port to transmit transparent data, select Transparent.
Select Terminal if you wish to operate the unit from a terminal.
After selecting a unit, the remaining parameters in the window
are set automatically and should not be changed.
Camera ID
If necessary, enter the ID of the peripheral you wish to control
(for example a dome camera or pan/tilt head).
Baud rate
Select the value for the transmission rate in bps.
Data bits
The number of data bits per character cannot be changed.
Stop bits
Select the number of stop bits per character.
Parity check
Select the type of parity check.
Interface mode
Select the desired protocol for the serial interface.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 103
9.10
Network
Network
>
>
>
>
>
Network
Advanced
Multicasting
JPEG Posting
Encryption
9.10.1
Network
The settings on this page are used to integrate the device into a
network. Some changes only take effect after a reboot. In this
case Set changes to Set and Reboot.
1. Make the desired changes.
2. Click Set and Reboot.
The device is rebooted and the changed settings are activated.
If the IP address, subnet mask, or gateway address is changed,
then the device is only available under the new addresses after
the reboot.
Automatic IP assignment
If a DHCP server is employed in the network for the dynamic
assignment of IP addresses, activate acceptance of IP
addresses automatically assigned to the device.
Certain applications (VIDOS, Bosch Video Management System,
Archive Player, Configuration Manager) use the IP address for
the unique assignment of the device. If using these
applications, the DHCP server must support the fixed
assignment between IP address and MAC address, and must be
appropriately set up so that, once an IP address is assigned, it
is retained each time the system is rebooted.
IP address
Enter the desired IP address for the camera. The IP address
must be valid for the network.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
104 en | Advanced Mode
Dinion2X IP Camera
Subnet mask
Enter the appropriate subnet mask for the set IP address.
Gateway address
For the device to establish a connection to a remote location in
a different subnet, enter the IP address of the gateway here.
Otherwise, this field can remain empty (0.0.0.0).
DNS server address
The device is easier to access if it is listed on a DNS server. For
example, to establish an Internet connection to the camera, it is
sufficient to enter the name given to the device on the DNS
server as a URL in the browser. Enter the DNS server's IP
address. Servers are supported for secure and dynamic DNS.
Details >>
Video transmission
If the device is used behind a firewall, TCP (Port 80) should be
selected as the transmission protocol. For use in a local
network, choose UDP.
Multicast operation is only possible with the UDP protocol. The
TCP protocol does not support multicast connections. The MTU
value in UDP mode is 1514 bytes.
HTTP browser port
Select a different HTTP browser port from the list if required.
The default HTTP port is 80. To limit connection to HTTPS,
deactivate the HTTP port. To do this, activate the Off option.
HTTPS browser port
To limit browser access to encrypted connections, choose an
HTTPS port from the list. The standard HTTPS port is 443.
Select the Off option to deactivate HTTPS ports and limit
connections to unencrypted ports.
The camera uses the TLS 1.0 protocol. Ensure that the browser
has been configured to support this protocol. Also ensure that
Java application support is activated (in the Java Plug-in
Control Panel of the Windows Control Panel).
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 105
To limit connections to SSL encryption, set the Off option in
the HTTP browser port, the RCP+ port, and Telnet support. This
deactivates all unencrypted connections allowing connections
on the HTTPS port only.
Configure and activate encryption for media data (video, audio,
metadata) on the Encryption page.
RCP+ port 1756
Activating RCP+ port 1756 allows unencrypted connections on
this port. To allow only encrypted connections, set the Off
option to deactivate the port.
Telnet support
Activating Telenet support allows unencrypted connections on
this port. To allow only encrypted connections, set the Off
option to deactivate telnet support, making telnet connections
impossible.
Interface mode ETH
If necessary, select the Ethernet link type for interface ETH.
Depending on the device connected, it may be necessary to
select a special operation type.
Network MSS (Byte)
Set the maximum segment size for the IP packet's user data
here. This gives the option to adjust the size of the data packets
to the network environment and to optimize data transmission.
Please comply with the MTU value of 1,514 bytes in UDP mode.
iSCSI MSS (Byte)
Specify a higher MSS value for a connection to the iSCSI
system than for the other data traffic via the network. The
potential value depends on the network structure. A higher
value is only useful if the iSCSI system is located in the same
subnet as the camera.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
106 en | Advanced Mode
Dinion2X IP Camera
Enable DynDNS
DynDNS.org is a DNS hosting service that stores IP addresses in
a database ready for use. It allows selecting the device via the
Internet using a host name, without having to know the current
IP address of the device. Enable this service here. To do this,
obtain an account with DynDNS.org and register the required
host name for the device on that site.
Note:
Information about the service, registration process and
available host names can be found at DynDNS.org.
Host name
Enter the host name registered on DynDNS.org for the device
here.
User name
Enter the user name registered at DynDNS.org here.
Password
Enter the password registered at DynDNS.org here.
Force registration now
Force the registration by transferring the IP address to the
DynDNS server. Entries that change frequently are not provided
in the Domain Name System. It is a good idea to force the
registration when setting up the device for the first time. Only
use this function when necessary and no more than once a day,
to avoid the possibility of being blocked by the service provider.
To transfer the IP address of the device, click the Register
button.
Status
The status of the DynDNS function is displayed here for
information purposes; these settings cannot be changed.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 107
9.10.2
Advanced
The settings on this page are used to set advanced settings the
network. Some changes only take effect after a reboot. In this
case Set changes to Set and Reboot.
1. Make the desired changes.
2. Click Set and Reboot.
The device is rebooted and the changed settings are activated.
SNMP
The camera supports the SNMP V2 (Simple Network
Management Protocol) for managing and monitoring network
components, and can send SNMP messages (traps) to IP
addresses. It supports SNMP MIB II in the unified code.
If On is selected for the SNMP parameter and a SNMP host
address is not entered, the device does not send the traps
automatically and will only reply to SNMP requests. If one or
two SNMP host addresses are entered, SNMP traps are sent
automatically. Select Off to deactivate the SNMP function.
1. SNMP host address / 2. SNMP host address
To send SNMP traps automatically, enter the IP addresses of
one or two target devices here.
SNMP traps
To choose which traps are sent:
1. Click Select. A dialog box appears.
2. Click the check boxes of the appropriate traps.
3. Click Set to close the window and send all of the checked
traps.
Authentication (802.1x)
To configure Radius server authentication, connect the camera
directly to a computer using a network cable. If a Radius server
controls access rights over the network, select On to activate
authentication to communicate with the device.
1. Enter the user name that the Radius server uses for the
camera in the Identity field.
2. Enter the Password that the Radius server expects from
the camera.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
108 en | Advanced Mode
Dinion2X IP Camera
RTSP port
If necessary, select a different port for the exchange of the
RTSP data from the list. The standard RTSP port is 554. Select
Off to deactivate the RTSP function.
9.10.3
Multicasting
In addition to a one-to-one connection between a camera and a
single receiver (unicast), the camera can enable multiple
receivers to receive the video signal simultaneously. This is
either done by duplicating the data stream in the device and
then distributing it to multiple receivers (multi-unicast), or by
distributing an individual data stream in the network itself to
multiple receivers in a defined group (multicast). Enter a
dedicated multicast address and port for each stream. Then
switch between the streams by clicking the associated tabs.
The prerequisite for multicast operation is a multicast-capable
network that uses the UDP and IGMP protocols. Other group
membership protocols are not supported. The TCP protocol
does not support multicast connections.
A special IP address (class D address) must be configured for
multicast operation in a multicast-enabled network. The
network must support group IP addresses and the Internet
Group Management Protocol (IGMP V2). The address range is
from 225.0.0.0 to 239.255.255.255. The multicast address can
be the same for multiple streams. However, it is then necessary
to use a different port in each case so that multiple data
streams are not sent simultaneously using the same port and
multicast address. The settings must be made individually for
each stream.
Enable
Enable simultaneous data reception on several receivers that
need to activate the multicast function. To do this, check the
box and then enter the multicast address.
Multicast Address
Enter a valid multicast address to be operated in multicast
mode (duplication of the data stream in the network). With the
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 109
setting 0.0.0.0 the encoder for the stream operates in multi-
unicast mode (copying of data stream in device). The camera
supports multi-unicast connections for up to five
simultaneously-connected receivers.
Duplication of data places a heavy demand on the CPU and can
lead to impairment of the image quality under certain
circumstances.
Port
Enter the port address for the stream here.
Streaming
Click the checkbox to activate multicast streaming mode. An
activated stream is marked with a check. (Streaming is typically
not required for standard multicast operation.)
Multicast packet TTL
A value can be entered to specify how long the multicast data
packets are active on the network. If multicast is to be run via a
router, the value must be greater than 1.
9.10.4
JPEG Posting
Save individual JPEG images on an FTP server at specific
intervals. If required, retrieve these images at a later date to
reconstruct alarm events. JPEG resolution corresponds to the
highest setting from the two data streams.
File name
Select how file names are created for the individual images that
are transmitted.
–
Overwrite: The same file name is always used and any
existing file will be overwritten by the current file.
Increment: A number from 000 to 255 is added to the file
name and automatically incremented by 1. When it reaches
255, it starts again from 000.
–
–
Date/time suffix: The date and time are automatically
added to the file name. When setting this parameter,
ensure that the date and time of the device are always set
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
110 en | Advanced Mode
Dinion2X IP Camera
correctly . For eample, the file snap011005_114530.jpg
was stored on October 1, 2005 at 11.45 and 30 seconds.
Posting interval
Enter the interval in seconds at which the images are sent to an
FTP server. Enter zero for no images to be sent.
FTP server IP address
Enter the IP address of the FTP server on which to save the
JPEG images.
FTP server login
Enter your login name for the FTP server.
FTP server password
Enter the password that gives access to the FTP server.
Path on FTP server
Enter an exact path to post the images on the FTP server.
9.10.5
Encryption
If an encryption license is installed, this submenu gives access
to the encryption parameters.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 111
9.11
Service
Service
>
>
>
Maintenance
Licenses
System Overview
9.11.1
Maintenance
CAUTION!
Before starting a firmware update, make sure to select the
correct upload file. Uploading the wrong files can result in the
device no longer being addressable, requiring it to be replaced.
Do not interrupt the firmware installation. Even changing to
another page or closing the browser window leads to
interruption. Interruption may lead to faulty coding of the Flash
memory. This can result in the device no longer being
addressable, requiring it to be replaced.
Firmware
The camera functions and parameters can be updated by
uploading new firmware. To do this, the latest firmware
package is transferred to the device via the network. The
firmware is installed there automatically. Thus, a camera can be
serviced and updated remotely without requiring a technician
to make changes to the device on site. The latest firmware can
be obtained from your customer service center or from the
Bosch Security Systems download area.
To update the firmware:
1. First, store the firmware file on your hard disk.
2. Enter the full path for the firmware file in the field or click
Browse to locate and select the file.
3. Click Upload to begin transferring the file to the device.
The progress bar allows monitoring of the transfer.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
112 en | Advanced Mode
Dinion2X IP Camera
The new firmware is unpacked and the Flash memory is
reprogrammed. The time remaining is shown by the message
going to reset Reconnecting in ... seconds. When the upload is
completed successfully, the device reboots automatically.
If the operating status LED lights up red, the upload has failed
and must be repeated. To perform the upload, switch to a
special page:
1. In the address bar of your browser, enter /main.htm after
the device IP address, for example:
192.168.0.10/main.htm
2. Repeat the upload.
Configuration
Save configuration data for the camera to a computer and load
saved configuration data from a computer to the device.
To save the camera settings:
1. Click Download; a dialog box appears.
2. Follow the instructions to save the current settings.
To load configuration data from the computer to the device:
1. Enter the full path of the file to upload or click Browse to
select the desired file.
2. Make certain that the file to be loaded comes from the
same device type as the device to be reconfigured.
3. Click Upload to begin transmission to the device. The
progress bar allows monitoring of the transfer.
Once the upload is complete, the new configuration is
activated. The time remaining is shown by the message going to
reset Reconnecting in ... seconds. When the upload is
completed successfully, the device reboots automatically.
SSL certificate
To work with an SSL connection, both sides of the connection
must have the appropriate certificates. Upload one or more
certificate files, one at a time, to the camera.
1. Enter the full path of the file to upload or click Browse to
locate the file.
2. Click Upload to start the file transfer.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Advanced Mode | en 113
Once all files have been successfully uploaded, the device must
be rebooted. In the address field of the browser, enter /reset
after the camera's IP address, for example:
192.168.0.10/reset
The new SSL certificate is valid.
Maintenance log
Download an internal maintenance log from the device to send
it to Customer Service for support purposes. Click Download
and select a storage location for the file.
9.11.2
9.11.3
Licenses
This window is for the activation of additional functions by
entering activation codes. An overview of installed licenses is
shown.
System Overview
This window is for information only and cannot be modified.
Keep this information at hand when seeking technical support.
Select the text on this page with a mouse and copy it so that it
can be pasted into an e-mail if required.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
114 en | Operation via the browser
Dinion2X IP Camera
10
Operation via the browser
10.1
Livepage
After the connection is established, the Livepage is initially
displayed. It shows the live video image on the right of the
browser window. Depending on the configuration, various text
overlays may be visible on the live video image. Other
information may also be shown next to the live video image on
the Livepage. The display depends on the settings on the
LIVEPAGE Functions page.
Figure 10.1 Livepage
10.1.1
Processor load
When accessing the camera with a browser, the processor load
and network information is available in the upper right of the
window next to the Bosch logo.
Move the mouse cursor over the icons to display numerical
values. This information can help with problem solving or when
fine tuning the device.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Operation via the browser | en 115
10.1.2
Image selection
View the image on a full screen.
–
Click the Stream 1, Stream 2 or M-JPEG tab below the
video image to switch between the different displays for
the camera image.
10.1.3
View Control
If the data port is set-up to control a PTZ device, a View Control
tab is shown and activated. Use the controls to position the
camera and to adjust zoom, focus and iris. Six pre-set positions
can be defined and selected.
Move the mouse cursor over the video image; additional options
for controlling peripherals are displayed with the mouse cursor.
10.1.4
Digital I/O
Depending on the configuration of the unit, the alarm input and
the relay output are displayed next to the camera image. The
alarm symbol is for information and indicates the input status
of the alarm input: Active 1 = Symbol lights, Active 0 = Symbol
not lit.
The relay on the camera allows the operation of a device (for
example, a light or a door opener).
–
To operate, click the relay symbol. The symbol is red when
the relay is activated.
10.1.5
10.1.6
System Log / Event Log
The System Log field contains information about the operating
status of the camera and the connection. These messages can
be saved automatically in a file. Events such as the triggering or
end of alarms are shown in the Event Log field. These messages
can be saved automatically in a file.
To delete the entries from the fields, click the icon in the top
right-hand corner of the relevant field.
Saving snapshots
Individual images from the video sequence that is currently
being shown on the Livepage can be saved in JPEG format on
the computer's hard drive.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
116 en | Operation via the browser
Dinion2X IP Camera
–
Click the camera icon
to save single images.
The storage location depends on the configuration of the
camera.
10.1.7
Recording video sequences
Sections of the video sequence that is currently being shown on
the Livepage can be saved on the computer's hard drive. The
sequences are recorded at the resolution specified in the
encoder configuration. The storage location depends on the
configuration of the camera.
1. Click the recording icon
to record video sequences.
–
Saving begins immediately. The red dot on the icon
indicates that a recording is in progress.
2. Click the recording icon again to stop recording.
Play back saved video sequences using the Player from
Bosch Security Systems.
10.1.8
10.1.9
Running recording program
The hard drive icon below the camera images on the Livepage
changes during an automatic recording.
The icon lights up and displays a moving graphic
to
indicate a running recording. If no recording is taking place, a
static icon is displayed.
Audio communication
Audio can be sent and received via the Livepage if the active
monitor and the remote station of the camera support audio.
1. Press and hold the F12 key to send an audio signal to the
camera.
2. Release the key to stop sending audio.
All connected users receive audio signals sent from the camera
but only the user who first pressed the F12 key can send audio
signals; others must wait for the first user to release the key.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Operation via the browser | en 117
10.2
Recordings page
Access the Recordings page for playing back recorded video
sequences from the Livepage as well as from the Settings
menu. The Recordings link is only visible if a storage medium
has been selected.
1. Click Recordings in the navigation bar in the upper section
of the window. The playback page appears and playback
begins immediately.
2. Select Recording 1 or 2 in the drop-down menu. (The
contents for 1 and 2 are identical, only the quality and
locaction may be different.)
10.2.1
Controlling playback
A time bar below the video image allows quick orientation. The
time interval associated with the sequence is displayed in the
bar in gray. A green arrow above the bar indicates the position
of the image currently being played back within the sequence.
The time bar offers various options for navigation in and
between sequences.
–
Change the time interval displayed by clicking the plus or
minus icons. The display can span a range from two
months to a few seconds.
–
–
If required, drag the green arrow to the point in time at
which the playback should begin.
Red bars indicate the points in time where alarms were
triggered. Drag the green arrow to navigate to these points
quickly.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
118 en | Operation via the browser
Dinion2X IP Camera
Control playback by means of the buttons below the video
image. The buttons have the following functions:
Start/Pause playback
Jump to start of active sequence or to previous sequence
Jump to start of the next video sequence in the list
Slide control
Continuously select playback speed by means of the speed
regulator:
Bookmarks
In addition, set markers in the sequences, so-called bookmarks,
and jump directly to these. These bookmarks are indicated as
small yellow arrows above the time interval. Use the bookmarks
as follows:
Jump to the previous bookmark
Set bookmark
Jump to the following bookmark
Bookmarks are only valid while in the Recordings page; they are
not saved with the sequences. All bookmarks are deleted when
you leave the page.
Trick mode
View recordings frame by frame in trick mode by using a mouse
with a scroll wheel. To do this, place the mouse cursor in the
timeline below the timescale and turn the scroll wheel.
Playback is automatically stopped (paused) during scrolling.
Trick mode requires significantly higher memory capacity and
computing power.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Troubleshooting | en 119
11
Troubleshooting
11.1
Function test
The camera offers a variety of configuration options. Therefore,
check that it works properly after installation and configuration.
This is the only way to ensure that the camera will function as
intended in the event of an alarm.
Your check should include the following functions:
–
–
–
–
Can the camera be called up remotely?
Does the camera transmit all the data required?
Does the camera respond as desired to alarm events?
Is it possible to control peripheral devices, if necessary?
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
120 en | Troubleshooting
Dinion2X IP Camera
11.2
Resolving problems
The following table is intended to help identify the causes of
malfunctions and correct them where possible.
Malfunction
Possible causes
Solution
No image
Defective camera.
Connect a local monitor
to the camera and check
the camera function.
transmission to
remote location.
Faulty cable connections. Check all cables, plugs,
contacts and
connections.
Incorrect encoder stream Select the H.264 BP+
property set for
connection to hardware
decoder.
(HW decoder) option on
the Encoder Streams
configuration page.
No connection
The unit's configuration.
Check all configuration
parameters.
established, no
image transmission.
Faulty installation.
Check all cables, plugs,
contacts and
connections.
Wrong IP address.
Check the IP addresses
(terminal program).
Faulty data transmission Check the data
within the LAN.
transmission with ping.
The maximum number of Wait until there is a free
connections has been
reached.
connection and call the
transmitter again.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Troubleshooting | en 121
Malfunction
Possible causes
Solution
No audio
Hardware fault.
Check that all connected
audio units are operating
correctly.
transmission to
remote station.
Faulty cable connections. Check all cables, plugs,
contacts and
connections.
Incorrect configuration.
Check audio parameters
on the Audio
configuration and
LIVEPAGE Functions
pages.
The audio voice
Wait until the connection
is free and then call the
sender again.
connection is already in
use by another receiver.
The unit does not
report an alarm.
Alarm source is not
selected.
Select possible alarm
sources on the Alarm
sources configuration
page.
No alarm response
specified.
Specify the desired alarm
response on the Alarm
connections
configuration page; if
necessary change the IP
address.
Control of cameras The cable connection
or other units is not between the serial
Check all cable
connections and ensure
all plugs are properly
fitted.
possible.
interface and the
connected unit is not
correct.
The interface parameters Make sure that the
do not match those of the settings of all units
other unit connected.
involved are compatible.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
122 en | Troubleshooting
Dinion2X IP Camera
Malfunction
Possible causes
Solution
Have the unit checked by
The unit is not
Power failure during
operational after a
firmware upload.
programming by firmware Customer Service and
file.
replace if necessary.
Incorrect firmware file.
Enter the IP address of
the unit followed by /
main.htm in your Web
browser and repeat the
upload.
Placeholder with a
JVM not installed on your Install Sun JVM from the
red cross instead of computer or not
product CD.
the ActiveX
activated.
components.
Web browser
contains empty
fields.
Active proxy server in
network.
Create a rule in the local
computer's proxy
settings to exclude local
IP addresses.
The POWER LED
Firmware upload failed.
Repeat firmware upload.
flashes red.
11.3
Customer service
If a fault cannot be resolved, please contact your supplier or
system integrator, or go directly to Bosch Security Systems
Customer Service.
The version numbers of the internal processors can be viewed
on a special page. Please note this information before
contacting Customer Service.
1. In the address bar of your browser, after the unit IP
address, enter: /version
for example: 192.168.0.80/version
2. Write down the information or print out the page.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Maintenance | en 123
12
Maintenance
12.1
Testing the network connection
The ping command can be used to check the connection
between two IP addresses. This allows testing whether a device
is active in the network.
1. Open the DOS command prompt.
2. Type ping followed by the IP address of the device.
If the device is found, the response appears as " Reply from ... ",
followed by the number of bytes sent and the transmission time
in milliseconds. Otherwise, the device cannot be accessed via
the network. This might be because:
–
The device is not properly connected to the network.
Check the cable connections in this case.
–
The device is not correctly integrated into the network.
Check the IP address, subnet mask, and gateway address.
12.2
Communication with Terminal Program
Data Terminal
If a camera cannot be found in the network or the connection to
the network is interrupted, you can connect a data terminal to
the camera for initial setup and for setting important
parameters. The data terminal consists of a computer with a
terminal program.
You require a serial transmission cable with a 9-pin Sub-D plug
to connect to the computer.
HyperTerminal, a communications accessory included with
Microsoft Windows, can be used as the terminal program.
1. Disconnect the camera from the Ethernet network before
working with the terminal program.
2. Connect the serial interface of the camera using any
available serial interface on the computer.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
124 en | Maintenance
Dinion2X IP Camera
Configuring the Terminal
Before the terminal program can communicate with the camera,
the transmission parameters must be matched. Make the
following settings for the terminal program:
–
–
–
–
–
19,200 bps
8 data bits
No parity check
1 stop bit
No protocol
Command Inputs
After the connection has been established, you must log on to
the camera to access the main menu. Other submenus and
functions can be accessed using the on-screen commands.
1. If necessary, turn off the local echo so that entered values
are not repeated on the display.
2. Enter one command at a time.
3. When you have entered a value, such as the IP address,
check the characters you have entered before pressing
Enter to transfer the values to the camera.
Assigning an IP Address
Before you can operate a camera in your network you must first
assign it an IP address that is valid for your network.
The following default address is preset at the factory:
192.168.0.1
1. Start a terminal program such as HyperTerminal.
2. Enter the user name service. The terminal program
displays the main menu.
3. Enter command 1 to open the IP menu.
4. Enter 1 again. The terminal program displays the current IP
address and prompts you to enter a new IP address.
5. Enter the desired IP address and press Enter. The terminal
program displays the new IP address.
6. Use the displayed commands for any additional settings
you require.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Maintenance | en 125
Note:
You must reboot to activate the new IP address, a new subnet
mask or a gateway IP address.
Reboot
Briefly interrupt the power supply to the camera for a reboot
(disconnect the power supply unit from the mains supply and
switch on again after a few seconds).
Additional Parameters
You can use the terminal program to check other basic
parameters and modify them where necessary. Use the on-
screen commands in the various submenus to do this.
12.3
Repairs
CAUTION!
Never open the casing of the unit. The unit does not contain any
user serviceable parts. Ensure that all maintenance or repair
work is performed only by qualified personnel (electrical
engineering or network technology specialists). In case of
doubt, contact your dealer's technical service center.
12.3.1
Transfer and disposal
The camera should only be passed on together with this
installation guide. The unit contains environmentally hazardous
materials that must be disposed of according to law. Defective
or superfluous devices and parts should be disposed of
professionally or taken to your local collection point for
hazardous materials.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
126 en | Technical Data
Dinion2X IP Camera
13
Technical Data
13.1
Specifications
Type number
Imager
NBN-498
1/3-inch CCD sensor
752x582
Active pixels (PAL)
Active pixels (NTSC) 768x494
Rated supply voltage 12 VDC, 550 mA (IVA: 650 mA)
24 VAC, 550 mA (IVA: 650 mA)
PoE 48 VDC, 200 mA (IVA: 250 mA)
Power consumption
≤6 W
Minimum illumination 0.15 lx color, 30 IRE
0.06 lx Mono, 30 IRE
Day/Night
Modes
Color, Mono (IR contrast), Auto
6 programmable (preset) modes: 24-hour, Traffic,
Low-light, SmartBLC, Low noise, Infrared
Dynamic range
SNR
120 dB (20-bit image processing)
> 50 dB
Dynamic engine
SmartBLC
AGC
XF-Dynamic, 2X-Dynamic, SmartBLC
On (includes 2X-Dynamics), Off
AGC On (0-30 dB) or Off
White Balance
Color saturation
Shutter
ATW, AWB hold and manual (2500 to 10000K)
Adjustable from monochrome (0%) to 133% color
AES (1/60 [1/50] to 1/10000) customer selectable
AES (1/60 [1/50] to 1/150000) automatic,
flickerless or fixed
Sens Up
Adjustable from Off to 10x
AutoBlack
Automatic continuous, Off
DNR
Automatic noise filtering On/Off selectable
Sharpness enhancement level selectable
Suppresses highlights in scenes
Sharpness
Peak White Invert
Privacy Masking
Four independent areas, fully programmable; gray
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Technical Data | en 127
Video Motion Analysis Motion+, Intelligent Video Analysis (option)
Test pattern
generator
Color bars 100%, Greyscale 11-step, Sawtooth 2H,
Checker board, Cross hatch, UV plane
Synchronization
ALC lens
Internal, Line Lock
Video or DC iris auto detect
OSD with softkey operation, Web browser
Actual shutter, Actual gain
Controls
Control feedback
LAN interface
1 × Ethernet 10/100 Base-T, automatic adaptation,
half/full duplex, RJ-45
Video encoding
protocols
H.264 (ISO/IEC 14496-10), M-JPEG, JPEG
Video data rate
9,600 KBit/s... 6 MBit/s
Image resolutions
(PAL/NTSC)
4CIF: 704 × 576/480 pixels (25/30 IPS)
CIF: 352 × 288/240 pixels (25/30 IPS)
Group of pictures
I, IP
Image refresh rate
Field/image-based
coding
1 to 50/60 fields/s, adjustable (PAL/NTSC)
Network protocols
Telnet, RTP, HTTP, ARP,TCP, UDP, IP, ICMP, DHCP,
IGMPv2, 802.1x, HTTPS, IGMPv3, SNMPv2, UPnP
Encryption
TLS 1.0, SSL, AES (optional)
Alarm input (2)
Relay output (1)
Non-isolated closing contact
TTL logic, +5V nominal, +40 VDC max, DC coupled
with 22 kOhm pull-up to +3.3
Maximum voltage 30 VAC or +40 VDC.
Maximum 0.5 A continuous, 10 VA
Audio input (Line in) 5.5 Vpp maximum, impedance 9 kOhm typical
Audio output (Line
out)
3 Vpp maximum, impedance 10 kOhm typical
Audio standard G.711 300 Hz to 3.4 kHz at 8 kHz sampling rate
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
128 en | Technical Data
Dinion2X IP Camera
Audio signal-to-noise > 50 dB
ratio
Data port
RS-232/422/485
Lens mount
CS compatible, C-mount compatible with adapter
ring
Tripod mount
Bottom and top 1/4" 20 UNC
Dimensions (H x W L) 58 x 66 x 122 mm (2.28 x 2.60 x 4.80 in)
without lens
Weight without lens
542 g (1.195 lb)
Operating
-20 °C to +50 °C (-4 °F to +122 °F)
temperature
Operating
-20 °C to +45 °C (-4 °F to +113 °F)
temperature (IVA)
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Technical Data | en 129
13.1.1
Dimensions
118 (4.646)
85 (3.346)
34 (1.339)
1/4"-20 UNC
Dinion2X D/N IP
1/4"-20 UNC
48 (1.889)
122 (4.803)
66 (2.598)
mm (in)
Figure 13.1 Side and front dimensions
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
130 en | Technical Data
Dinion2X IP Camera
13.1.2
Accessories
Recommended lenses
LTC 3364/21 Varifocal Lens IR corrected
–
1/3-inch, 2.8 – 6 mm, DC-iris, CS-mount F1.4-200, 4-pin
LTC 3664/30 Varifocal Lens IR corrected
1/3-inch, 3.0 – 8 mm, DC-iris, CS-mount F1.0-360, 4-pin
LTC 3664/40 Varifocal Lens IR corrected
1/3-inch, 2.8 – 11 mm, DC-iris, CS-mount F1.4-360, 4-pin
LTC 3674/20 Varifocal Lens IR corrected
1/3-inch, 7.5 – 50 mm, DC-iris, CS-mount F1.3-360, 4-pin
LTC 3764/20 Varifocal Lens IR corrected
1/2-inch, 4 – 12 mm, DC-iris, C-mount F1.2-360, 4-pin
LTC 3774/30 Varifocal Lens IR corrected
1/2-inch, 10 – 40 mm, DC-iris, C-mount F1.4-360, 4-pin
–
–
–
–
–
Power transformers
UPA-2410-60 Power Supply
–
120 VAC, 60 Hz, 24 VAC, 10 VA Out
UPA-2430-60 Power Supply
120 VAC, 60 Hz, 24 VAC, 30 VA Out
UPA-2450-60 Power Supply
120 VAC, 60 Hz, 24 VAC, 50 VA Out
UPA-2420-50 Power Supply
220 VAC, 50 Hz, 24 VAC, 20 VA Out
UPA-2450-50 Power Supply
220 VAC, 50 Hz, 24 VAC, 50 VA Out
–
–
–
–
Contact your Bosch representative for the latest available
accessories.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Glossary | en 131
Glossary
0…9
10/100Base-TIEEE-802.3 specification for 10 or 100 Mbps Ethernet.
802.1x
The IEEE 802.1x standard provides a general method for
authentication and authorization in IEEE-802 networks.
Authentication is carried out via the authenticator, which
checks the transmitted authentication information using an
authentication server (see RADIUS server) and approves or
denies access to the offered services (LAN, VLAN or WLAN)
accordingly.
A
ARP
Address Resolution Protocol: a protocol for mapping MAC and
IP addresses.
B
Baud
bps
Unit of measure for the speed of data transmission
Bits per second, the actual data rate.
C
CF
CompactFlash: interface standard, for digital storage media
amongst other things. Used in computers in the form of CF
cards, digital cameras and Personal Digital Assistants (PDA).
Common Intermediate Format: video format with 352 × 288/
240 pixels.
CIF
D
DHCP
DNS
Dynamic Host Configuration Protocol: uses an appropriate
server to enable dynamic assignment of an IP address and other
configuration parameters to computers on a network (Internet
or LAN).
Domain Name Service: A service that stores domain names and
translates them into Internet Protocol (IP) addresses.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
132 en | Glossary
Dinion2X IP Camera
F
FTP
File Transfer Protocol: Used to transfer files between
computers on a network, such as the Internet.
Full duplex Simultaneous data transmission in both directions (sending and
receiving).
G
GBIC
GoP
GigaBit Interface Converter: applied in network technology to
render interfaces flexible, for converting an electrical interface
into an optical interface, for example. This enables flexible
operation of an interface as a Gigabit Ethernet via twisted-pair
cables or fiber optic cables.
Group of Pictures: In MPEG video encoding, a group of pictures,
or GoP, specifies the order in which intra-frames and inter-
frames are arranged.
H
H.264
Standard for high-efficiency video compression, based on the
predecessors MPEG-1, MPEG-2 and MPEG-4. H.264 typically
achieves a coding efficiency around three times as high as
MPEG-2. This means that comparable quality can be achieved at
around a third of MPEG-2 data quantity.
HTTP
Hypertext Transfer Protocol: protocol for transmitting data over
a network.
HTTPS
Hypertext Transfer Protocol Secure: encrypts and authenticates
communication between Web server and browser.
I
ICMP
Internet Control Message Protocol: One of the core protocols of
the Internet protocol suite. It is chiefly used by networked
computers' operating systems to send error messages
indicating, for instance, that a requested service is not available
or that a host or router could not be reached.
ID
Identification: a machine readable character string.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Glossary | en 133
IEEE
Institute of Electrical and Electronics Engineers: The world's
leading professional association for the advancement of
technology.
IGMP
Internet Group Management Protocol: A communications
protocol used to manage the membership of Internet Protocol
multicast groups.
Internet ProtocolThe main protocol used on the Internet, normally in
conjunction with the Transfer Control Protocol (TCP): TCP/IP.
IP
See Internet Protocol.
IP address A 4-byte number uniquely defining each unit on the Internet. It
is usually written in dotted decimal notation, for example
"209.130.2.193"
iSCSI
Internet Small Computer System Interface: Protocol that
manages storage via a TCP/IP network. iSCSI enables access to
stored data from everywhere in the network.
ISDN
Integrated Services Digital Network: Comprised of digital
telephony and data-transport services offered by regional
telephone carriers. ISDN involves the digitization of the
telephone network, which permits voice, data, text, graphics,
music, video, and other source material to be transmitted over
existing telephone wires.
J
JPEG
Joint Photographic Experts Group: The name of the committee
that created a standard for encoding still images.
K
Kbps
LAN
Kilobits per second: the actual data rate.
L
Local Area Network: A communications network serving users
within a limited geographical area such as a building or
university campus. It is controlled by a network operating
system and uses a transfer protocol.
LUN
Logical Unit Number: logical drive in iSCSI storage systems.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
134 en | Glossary
Dinion2X IP Camera
M
MAC
Media Access Control: A quasi-unique identifier attached to
most network adapters (NICs). It is a number that acts like a
name for a particular network adapter.
MIB
Management Information Base: a collection of information for
remote servicing using the SNMP protocol.
MPEG-4
A further development of MPEG-2 designed for transmitting
audiovisual data at very low transfer rates (for example over the
Internet).
MSS
Maximum Segment Size: maximum byte figure for the user data
in a data packet.
N
Net mask
NTP
A mask that explains which part of an IP address is the network
address and which part is the host address. It is usually written
in dotted decimal notation, for example "255.255.255.192"
Network Time Protocol: a standard for synchronizing computer
system clocks via packet-based communication networks. NTP
uses the connectionless network protocol UDP. This was
developed specifically for enabling time to be reliably
transmitted over networks with variable packet runtime (Ping).
O
OF
Optical Fiber: now used predominantly as the transmission
medium for line-borne telecommunication processes (glass
fiber cable).
P
Parameters Values used for configuration.
Q
QCIF
Quarter CIF: video format with 176 × 144/120 pixels (see CIF).
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Dinion2X IP Camera
Glossary | en 135
R
RADIUS serverRemote Authentication Dial-In User Service: a client/server
protocol for the authentication, authorization and accounting of
users with dial-up connections on a computer network. RADIUS
is the de-facto standard for central authentication of dial-up
connections via Modem, ISDN, VPN, Wireless LAN (see 802.1x)
and DSL.
RFC 868
A Request For Comment protocol for synchronizing computer
clocks over the Internet.
RS232/RS422/RS485 Recommended standards for serial data transmission.
A communication interface for third party control, firmware
upgrades, and service purposes for camera and DVR products.
RTP
Realtime Transport Protocol: a transfer protocol for real-time
video and audio.
S
SFP
Small Form-factor Pluggable: small, standardized module for
network connections, designed as a plug connector for high-
speed network connections.
SNIA
Storage Networking Industry Association: association of
companies for defining the iSCSI standard.
Simple Network Management Protocol: a protocol for network
management, for managing and monitoring network
components.
SNMP
SNTP
SSL
Simple Network Time Protocol: a simplified version of NTP (see
NTP).
Secure Sockets Layer: an encryption protocol for data
transmission in IP-based networks. The predecessor to TLS (see
TLS).
Subnet maskSee Net mask.
T
TCP
Transfer Control Protocol
Telnet
Login protocol with which users can access a remote computer
(Host) on the Internet or local area network (LAN) connections.
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
Download from Www.Somanuals.com. All Manuals Search And Download.
136 en | Glossary
Dinion2X IP Camera
TLS
TTL
Transport Layer Security: TLS 1.0 and 1.1 and the standard
advanced developments of SSL 3.0 (see SSL).
Time-To-Live: life cycle of a data packet in station transfers.
U
UDP
URL
User Datagram Protocol: One of the core protocols of the
Internet Protocol suite.
Uniform Resource Locator: Previously Universal Resource
Locator. The unique address for a file that is accessible on the
Internet.
UTP
Unshielded Twisted Pair: A variant of twisted pair cabling, UTP
cable is not surrounded by any shielding.
W
WAN
Wide Area Network: A long distance link used to extend or
connect remotely located local area networks.
AR18-10-B006 | v1.1 | 2010.06
Installation and Operation Manual
Bosch Security Systems
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Bosch Security Systems
www.boschsecurity.com
© Bosch Security Systems, 2010
Download from Www.Somanuals.com. All Manuals Search And Download.
|