TC9217MM-W, TC9220MM-W, TC9227MM-W
Instruction Manual
EN Monitor Mounts
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Assembly
BOSCH Monitor Wall Mounts
Models: TC9217MM-W, TC9220MM-W,
TC9227MM-W
BOSCH
Before you start make sure all parts
shown (see parts list, page 9) are
included with your bracket.
IMPORTANT! Read entire
instruction sheet before you
start installation and assembly.
This product is intended for use with UL
Listed products and must be installed by a
qualified professional installer.
R
IMPORTANT! If attaching a VCR Mount
Product is UL rated up to ___ TV
sizes, per attached chart
carefully study both product instruction sheets
before assembly. The interface bracket
(included with the VCR Mount) must be
attached during monitor mount assembly to
avoid disassembly later.
TV size
17"
Model #:
TC9217MM-W
TC9220MM-W
TC9227MM-W
21"
27"
Each monitor mount is for use with a single TV or monitor of a specified size only.
SIDE VIEW
TV
TV
A
CENTEROF
GRAVITY
B
C
FLOOR
Place TV onto a piece of pipe as
shown. (Pipe should be a few inches
wider than the TV.) Roll TV back and
forth to find the balance point. This is
the center of gravity. Mark the center
of gravity on the side of the TV.
Adjust support tray (A, three
pieces) to match width of TV.
Lock support tray using four
carriage bolts (B), washer/
nut combo (C). Tighten
securely.
Attachadhesive
pads (X) to top
clamps (Q).
CC
R
Q
Insert plastic
covers(CC)onto
endsofanti-rollout
hooks(R).
X
ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05
3 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach support tray (A)
to vertical support arms
(P) as shown.
Note: Choose the square
hole which aligns closest
with the center of gravity
mark on the TV (as
Y
R
determined in step 1).
Attach anti-rollout hooks
(R) as shown using M6
screws(Z)andretainer
bars (Y). Note: Extruded
side of retainer bar (Y)
goestowardsanti-rollout
hook(R).
R
Y
Z
P
P
E
Y
Hand tighten only.
R
A
J
O P T I O N A L
Although top clamps (Q) and anti-rollout
hooks (R) [see step 7] will provide more than
adequate support for the TV, some installers
may wish to also attach the support tray to
the TV bottom.
F
A
Using uni-clips (G) and M5 screws (F) (see
instruction card in fastener pack), or #10 x
3/4" particle board screws (H) and washers
(I) (for attachment to mounting bosses if
present), or a combination of both, attach
support tray (A) to TV bottom. [To do this
place TV upside down on a flat stable
surface and position support tray upside
down on TV bottom.] Attach at four places
as close to the four corners of the TV bottom
as possible.
G
H
I
TV
(UPSIDE DOWN)
ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05
4 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
For Wood Stud Walls drill three 5/32" (4 mm) dia. holes to a minimum depth of 2.5" (64 mm) into stud center.
Attach wall arm (W) using three #14 x 2.5" (6 mm x 65 mm) wood screws (V).
WARNING
• Tighten wood screws so wall arm is firmly attached, but do not tighten with excessive force! Overtightening can
cause stress damage to wood screws, greatly reducing their holding power. Tighten to 80 in • lb (9 N.M.) maxi-
mum torque.
W
V
ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05
5 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
• When installing BOSCH wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete
surface in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifica-
tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill
to avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the wall will safely support four times the combined load of the equipment and all attached hard-
ware and components.
For Concrete Walls use wall arm (W), making sure
that it is level, as a template to mark holes. Drill 1/
1
concrete
wall
4" (6 mm) dia. holes to a minimum depth of 2.5" (64
mm). Insert concrete anchors in holes flush with
wall as shown (right). Place wall arm (W) over
anchors and secure with #14 x 2.5" (6 mm x 65
mm) wood screws (V). Tighten all fasteners.
ACC 204
Drill hole(s) and insert anchor(s)
WARNING
2
wall arm
• Tighten wood screws so that wall plate is firmly
attached, but do not overtighten. Overtightening can
damage the screws, greatly reducing their holding
power.
ACC 204
• Never tighten in excess of 80 in • lb (9 N.M.).
Place arm over anchor(s) and secure with screw(s)
• Make sure that mounting screws are anchored into the
center of the studs. The use of an "edge to edge" stud
finder is highly recommended.
3
WARNING
• Concrete anchors are not intended for attachment to
concrete wall covered with a layer of plaster, drywall,
or other finishing material. If mounting to concrete wall
covered with plaster/drywall is unavoidable, plaster/
drywall (up to 5/8" thick) must be counterbored as
shown below. If plaster/drywall is thicker than 5/8",
custom fasteners must be supplied by installer.
Tighten all fasteners
CUTAWAYVIEW
ACC 204
INCORRECT
CORRECT
CONCRETE
WALL
wall
arm
concrete
concrete
wall
arm
W
plaster/
dry wall
plaster/
dry wall
V
ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05
6 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: Slots in corners of top clamps (Q) and corners of vertical support arms (P) allow for the installation of safety belt
(model ACC 666, sold separately). If using this belt, install it now.
DETAIL 1
Q
Q
Q
DETAIL 2
R
Z
Q
R
P
R
A
P
R
K
P
Position TV onto support tray (A). Position anti-rollout hooks (R) against front edge of TV.
WARNING
• Each anti-rollout hook (R) should have at least 1/4” of surface contact with the front of the TV. If this is not the
case the support tray (A) must be adjusted smaller [see step 2], or the vertical support arms (P) adjusted inward
[see step 4].
Insert top clamps (Q). Note: Top clamps (Q) fit between rollout protectors (R) and vertical support arms (P)
[DETAIL 1]. Press down on each top clamp (Q) while securely tightening each M6 screw (Z).
By hand, thread one serrated flange head screw (K) into each vertical support arm (P) into one of three threaded
holes [1, 2, or 3; DETAIL 2]. Choose the threaded hole that will allow just enough tilt clearance [see step 9].
Leaveabout1/4"ofexposedthread.
FIRST: From the top fully thread flush mount tube
(T) into threaded fitting in wall arm or ceiling plate.
Install the wall arm or ceiling plate according to
instructions included with it.
WMJ 025H
NEXT: Attach right and left tilt brackets (AA & BB)
to horizontal support (S) using four screws &
WMJ 018,
WMJ 022
T
CMJ 470,
CMJ 480,
CMJ 490
*
washer combo (J). Before tightening screws make
sure tilt brackets are adjusted horizontally to align
precisely with screws in the side of vertical support
arms (P). Attach horizontal support (S) to wallarm
or ceiling plate using fiber washers (M & N), spacer
(U, only included with smaller models) and retaining
collar (O). IMPORTANT:Retainingcollar(O)
** U
T
N
S
BB
requires a safety screw [refer to DETAIL 3, page 8].
M
O
FINALLY: Be sure that hooks in right and left tilt
brackets (AA & BB) are open end forward. Hang the
TV / bracket assembly.
AA
J
WARNING
• Do not lift more weight than you can handle!
Use additional manpower or mechanical lifting
equipment to safely lift and hang the TV /
Bracket assembly!
Wall arms & ceiling plates
include their own
instructions. Fixed length
and adjustable extension
columns are also available.
*
Included with models
TC9217MM and
TC9220MM only.
**
Insert one screw & washer combo (J) through slot
in each tilt bracket (AA & BB). Hand tighten.
P
ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05
7 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
S
T
F
S
O
When attaching the horizontal support (S) to wall arm or
ceiling plate, carefully thread retaining collar (O) onto end of
flush mount (T) tube (or extension column). Tighten at least
four complete turns ending with one of the small threaded
holes aligned with slot in the end of flush mount tube (T) (or
extension column). Insert and tighten one M5 screw (F).
DETAIL 3
(BOTTOM VIEW)
WARNING
• Set screw (F) is self tapping and may be hard to get
started but is essential to this installation. Failure to
install this screw can cause the mount to fall.
TIL
T
CLEARANCE
Adjust TV to desired tilt then tighten screws. Maximum tilt
is 30°. If tilt clearance is a problem revisit step 7, DETAIL 2.
WARNING
• Tighten all screws securely.
ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05
8 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
TC9217MM-W TC9220MM-W TC9227MM-W
Description
Qty.
1
1
1
4
4
2
6
4
4
4
8
2
1
1
1
2
2
2
1
1
1
4
1
2
2
2
1
1
2
Part #
Part #
Part #
left end support tray
right end support tray
center support tray
5/16 - 18 x 1/2" carriage bolt
5/16-18 washer/nut combo
M10-1.5 x .7 flange nut
M5 x .8 x 10 mm screw
uni-clip
128-1023
128-1024
128-1128
520-9207
530-1016
520-9261
520-9250
2245-081
500-9006
540-9400
520-1041
520-1105
540-9432
540-9431
1800-375
128-1107
128-1138
128-1116
128-1016
1446-014
128-0067
128-1026
128-1027
128-1134
520-9207
530-1016
520-9261
520-9250
2245-081
500-9006
540-9400
520-1041
520-1105
540-9432
540-9431
1800-375
128-1109
128-1138
128-1116
128-1017
1446-014
128-0067
128-1026
128-1027
128-1135
520-9207
530-1016
520-9261
520-9250
2245-081
500-9006
540-9400
520-1041
520-1105
540-9432
540-9431
1800-375
128-1111
128-1138
128-1116
128-1018
1446-014
-
A1
A2
A3
B
C
E
F
G
H
#10 x 3/4" particle board screw
#10 flat washer
I
M10 socket head lock/flat washer combo screw
M10 serrated flange head screw
fiber washer - large inside dia.
fiber washer - small inside dia.
retaining collar
J
K
M
N
O
P
vertical support arm
top clamp
anti-rollout hook
Q
R
horizontal support
S
flush mount tube
T
spacer
U
#14 x 2.5" (6 mm x 65 mm) screw
single wall arm
adhesive pads (not shown)
retainer bar
5S1-015-C03 5S1-015-C03 5S1-015-C03
V
W
X
128-1059
570-0024
128-1117
520-1166
128-1342
128-1341
590-1055
128-1059
570-0024
128-1117
520-1166
128-1337
128-1336
590-1055
128-1069
570-0024
128-1117
520-1166
128-1337
128-1336
590-1055
Y
M6 x 18mm flat phillips screw
tilt bracket right
tilt bracket left
Z
AA
BB
CC
plastic cover for anti-rollout hook
Note: Parts may appear slightly different than illustrated.
R
T
Y
U
N
Y
P
B
BB
S
M
O
A1
W
R
P
X
A3
Q
C
X
AA
A2
Q
V
E
F
K
H
J
I
G
Z
CC
ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05
9 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL WALLMOUNTKITSPECIFICATIONS
Mount
TV/Monitor
ProductBOSCHrated
when attached to...
Support
Tray
Depth(D)
concrete,
wood
Model
Number
cinder block
or brick
stud
Screen Size
125 lb
(57 kg)
150 lb
(65 kg)
10"
(254 mm)
13" - 17"
TC9217MM-W
TC9220MM-W
(330 mm) (432 mm)
125 lb
(57 kg)
150 lb
(65 kg)
14"
(356 mm)
19" - 21"
(482 mm) (533 mm)
125 lb
(57 kg)
150 lb
(65 kg)
14"
(356 mm)
25" - 28"
TC9227MM-W
(635 mm) (686 mm)
Reach (R)
18" (457 mm) for models TC9217MM-W, TC9220MM-W.
22.5" (572 mm) for models TC9227MM-W.
WARNING
• Weight of TV or monitor not to exceed Max. Load
Capacity (BOSCH rating)!
R
300 tilt
range
TV
support tray
D
ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05
10 of 12
Download from Www.Somanuals.com. All Manuals Search And Download.
11 of 12
ISSUED: 06-25-99 SHEET #: 039-9003-8 02-08-05
Download from Www.Somanuals.com. All Manuals Search And Download.
Americas
Europe, Middle East, Africa
Bosch Security Systems B.V.
P.O. Box 80002
5600 JB Eindhoven, The Netherlands
E-mail:
Asia-Pacific
Bosch Security Systems Pte Ltd
38C Jalan Pemimpin
Singapore 577180, Singapore
Phone: +65 319 3488
Bosch Security Systems
130 Perinton Parkway
Fairport, New York, 14450, USA
Phone: +1 (585) 223 4060
Fax:
+1 (585) 223 9180
Fax:
E-mail:
+65 319 3499
E-mail: [email protected]
© 2005 Bosch Security Systems GmbH
3935 890 28113 05-05 | February 3, 2005 | Data subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
|