In Car Video
IVMS-5601
IVMS-7001
Operating and installation instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Notes / Accessories .............. 14
Fitting ..................................... 14
Prepare the working area .............. 14
Mark out the dimensions................ 15
Carefully cut open the headrest
cover............................................. 15
Open the headrest and remove
filling and other items..................... 15
Lay the cable through the
headrest ........................................ 16
Insert the mounting frame in
the headrest .................................. 16
Insert the monitor .......................... 16
Check and adjust the monitor then
apply the Velcro strips ................... 17
Removal ................................. 17
OSD functions........................ 18
Main menu .................................... 18
Sub-menu ..................................... 18
Technical data ........................ 19
Guarantee .............................. 20
13
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES / ACCESSORIES
Important notes
FITTING/REMOVAL
Fitting
This device is not intended for fitting in
the forward section of the passenger
compartment where it could also be
seen by the driver. Fitting this device in
any part of the vehicle where it could
interfere with or distract the driver’s at-
tention is dangerous and is not permit-
ted. The manufacturer cannot accept
responsibility for any damage caused
as a result of improper fitting of this de-
vice.
Note
It is recommended that the fitting is car-
ried out at a specialist workshop.
Prepare the working area
➮ Remove the headrest, and place it
on a working surface that has been
cleared and cleaned, where the
further assembly procedures may
be carried out.
Note:
Take appropriate action to ensure that
the headrest is not damaged while fit-
ting the monitor.
To avoid the risk of electrical
shock, the device must be protected
from water and moisture, and must
not be opened. Dangerously high
voltages are generated inside the
device.
We wish to point out that the right to
claim against warranty is invalidated by
any changes or modifications to the
device that have not been explicitly ap-
proved by the manufacturer.
Accessories supplied
Connecting cable
Extraction tool
Operating instructions
14
Download from Www.Somanuals.com. All Manuals Search And Download.
FITTING/REMOVAL
Mark out the dimensions
➮ Feel the covering of the headrest
carefully to ensure that there are
no invisible parts that would pre-
vent the monitor from being fitted.
Use the cardboard template provided
to mark out the area that will need to be
cut.
Open the headrest and remove
filling and other items
➮ Carefully lift the covering material
away from the cut area.
➮ Adjust the cutting depth of the knife
to about 2.5 cm, and cut into the
headrest following a line about
0.5 cm inside the marked edge.
Carefully cut open the headrest
cover
Use a knife with an adjustable cutting
depth to cut out the planned area.
➮ Carefully lift the filling material at
one corner, and cut deeper into the
material with the knife.
➮ Remove the filling material in small
pieces.
➮ Make the first cut inside the
marked area at a point about
0.5 cm from one of the corners,
then make a diagonal cut to a point
about 0.5 cm from the opposite
corner.
➮ As you do this, lift one piece of the
filling material, and ensure that the
cut is being made to an even
depth.
To remove other pieces, use a Dremel
saw or another suitable tool.
➮ Make a similar cut between the
other two diagonally opposed cor-
ners.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
FITTING/REMOVAL
➮ Insert the monitor to check that it
will fit into the cut area, and make
adjustments if necessary.
Insert the mounting frame in the
headrest
➮ Before connecting the monitor,
pass the connecting cables
through the holes provided in the
mounting plate, as shown in the il-
lustration.
➮ Insert the mounting plate into the
area that has been cut out, and fix
it in place with appropriate fasten-
ings.
Lay the cable through the
headrest
➮ Now pass the supplied cables
through the opening so that they
emerge from the underneath of the
headrest.
➮ If possible, cover the cable with a
cable tunnel.
Inserting the monitor
➮ Now connect the power supply,
ground and video signal cables, to
check that the monitor is working.
➮ Before connecting the monitor,
pass the connecting cables
through the holes provided in the
mounting plate, as shown in the il-
lustration.
➮ Insert the monitor into the mounting
plate, and attach it with appropriate
fastenings.
Monitor
Mounting plate
16
Download from Www.Somanuals.com. All Manuals Search And Download.
FITTING/REMOVAL
Check and adjust the monitor
then apply the Velcro strips
➮ Connect the monitor, place it tem-
porarily in the cut-out, and place
the headrest into position.
Removal
➮ To remove the screen, insert the
extraction tool between the screen
and the mounting plate.
➮ Insert the extraction tool at the
place where a slot has been pro-
vided between the screen and the
mounting plate.
➮ Check the various monitor settings
such as brightness, headphone
function, volume control and so on.
➮ Then attach the Velcro strips to the
rear of the monitor, and push the
frame onto the headrest.
Take care not to press the screen
itself, and apply pressure only in
the region of the frame.
Extraction tool
17
Download from Www.Somanuals.com. All Manuals Search And Download.
FUNCTION
OSD functions
Main menu
➮ Call up the main menu by pressing
the “MODE” key on the main de-
vice, or “MENU” on the remote
control unit.
Sub-menu
➮ To reach the following menu op-
tions, select “MISC” from the main
menu.
➮ When in the sub-menu, select the
“MAIN MENU” option to return to
the main menu, then select “EXIT”
to leave the OSD menu.
➮ Select the “EXIT” option to leave
the OSD menu again.
AUTO PROGRAM
VOLUME
BRIGHTNESS
CONTRAST
COLOR
TINT
FM CHAN: OFF
AV OUT: LINE
ZOOM: FULL
SPEAKER: OFF
MISC
REVOLVE: LEFT RIGHT
REVOLVE: UP DOWN
RESET PICTURE
MAIN MENU
EXIT
+
➮ VOLUME:
Note:
Volume adjustment
➮ BRIGHTNESS:
Brightness adjustment
➮ CONTRAST:
Contrast adjustment
➮ COLOR:
Rotate UP DOWN (off function).
➮ AUTO PROGRAM :
See the “AUTO PROGRAM” function
in the description of the remote control
unit.
➮ AV OUT:
Color adjustment
➮ TINT:
Use this option to select between the
“constant” and “variable” AV output
modes.
Screen tint adjustment
➮ MISC:
Opens the sub-menu
➮ EXIT:
Leave the OSD menu
18
Download from Www.Somanuals.com. All Manuals Search And Download.
FUNCTION
TECHNICAL DATA
➮ ZOOM :
Technical data
This mode is pre-set by default to “full”.
You can make the various adjustments
for the display mode that you want by
System:
NTSC/PAL dual
system
pressing the
lowing options:
or
keys for the fol-
Power supply / consumption:
112 V DC
Full = display a 4:3 signal in a 16:9 im-
age format
± 10%, <700 mA
Standby:
< 1 mA
ZOOM1 = picture height, zoom factor =
4/3
Video input level: Combined video
signal 0.7 -
WIDTH1 = picture height and different
picture width
2.0 Vp-p, 75 Ohm
Normal = edge ratio 4:3
Audio input level: 0 - 0.3 Vrms,
10 - 20 kHz
ZOOM2 = zoom factor = 8/7
WIDTH = different picture widths
WIDTH2 = picture height and different
picture width
Operating temperature:
0° C - +60° C
ZOOM3 = picture height, zoom factor =
8/7
Storage temperature:
-20° C - +70° C
➮ SPEAKER:
Choose the “SPEAKER” option, then
switch the monitor loudspeaker on or
Screen size (diagonal):
5.6", 7"
off with the or
keys.
➮ REVOLVE
Contrast ratio:
150
With this function and the and keys
you can revolve the display on the Electrical power consumption:
screen.
< 9 W
➮ RESET:
Brightness:
400 cd/m2
Select the “RESET PICTURE” option to
return all the adjusted parameters to
their factory pre-set values.
Screen technology:
TFT (thin film tran-
➮ MAIN MENU:
sistor) display sys-
tem
If you are in the sub-menu, select this
option to return to the main menu.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DATA
GUARANTEE
Resolution (pixels):
Guarantee
The scope of the guarantee depends
on the regulations in force within the
country in which the unit was purchased.
5.6":
720 (H) x 234 (W) =
168,480 pixels
7":
1440 (H) x 234 (W)
= 336,960 pixels
If your unit develops a fault, please con-
tact your dealer and present the pur-
chase receipt.
Black light:
cold cathode tube
If the statutory guarantee period in your
country is less than 12 months, Blau-
punkt will grant a 12-month manufac-
turer’s guarantee. This guarantee does
not cover damage due to wear, incor-
rect usage or commercial use.
Visible screen area:
155.52 (W) x
87.75 (H) mm
Angle of view:
5.6":
from left and right:
45°,
from above: 10°,
from below: 30°
If you wish to enforce a claim under the
manufacturer’s guarantee that is provid-
ed by Blaupunkt, please send the faulty
equipment together with the purchase
receipt to the Blaupunkt customer serv-
ice centre in your country. You can find
out which address is closest to you by
contacting the telephone hotline listed
on the back page of this booklet. Blau-
punkt retains the right to rectify defects
or supply a replacement.
7":
from left and right:
60°,
from above: 60°,
from below: 30°
Full monitor dimensions:
5.6":
140 (W) x 114 (H) x
42 (D) mm
7":
200 (W) x 127 (H) x
33,5 (D) mm
Monitor weight: < 500 g
Subject to changes!
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Service-Nummern / Service numbers / Numéros du service après-
vente / Numeri del servizio di assistenza / Servicenummers /
Telefonnummer för service / Números de servicio / Números de
serviço / Servicenumre
Country:
Phone:
Fax:
WWW:
Germany
(D)
0180-5000225
05121-49 4002
Austria
(A)
(B)
01-610 390
02-525 5454
01-610 393 91
02-525 5263
44-898 644
09-435 99236
01-4010 7320
01-89583 8394
01-576 9473
01-4598830
02-369 6464
40 2085
Belgium
Denmark
Finland
France
(DK) 44 898 360
(FIN) 09-435 991
(F)
01-4010 7007
Great Britain (GB) 01-89583 8880
Greece
Ireland
Italy
(GR) 0800-550 6550
(IRL) 01-4149400
(I)
02-369 6331
40 4078
Luxembourg (L)
Netherland
Norway
Portugal
Spain
(NL)
023-565 6348
66-817 000
01-2185 00144
902-120234
08-7501500
023-565 6331
66-817 157
01-2185 11111
916-467952
08-7501810
01-8471650
(N)
(P)
(E)
(S)
Sweden
Switzerland (CH) 01-8471644
Czech. Rep. (CZ)
02-6130 0441
01-333 9575
0800-118922
02-6130 0514
01-324 8756
022-8771260
Hungary
(H)
Poland
(PL)
Turkey
USA
(TR)
0212-3350677
0212-3460040
708-6817188
(USA) 800-2662528
Brasil
(Mercosur)
(BR) +55-19 3745 2769 +55-19 3745 2773
Malaysia
(Asia Pacific) (MAL) +604-6382 474
+604-6413 640
Blaupunkt GmbH
09/01
CM/PSS2 - 8 622 403 143
Download from Www.Somanuals.com. All Manuals Search And Download.
|