GL544
GL545
Download from Www.Somanuals.com. All Manuals Search And Download.
4
3
2
7
5
1
6
8
10
5
6
9
1
Download from Www.Somanuals.com. All Manuals Search And Download.
3
2.2
2.3
2.1
2.4
10
11
13
12
14
12
A
E
B
C
D
°
20
F
G
H
J
50mm
Download from Www.Somanuals.com. All Manuals Search And Download.
4
15
3.1
4
5
19
16
18
9
17
6
MAX
21
20
7.2
7.1
3.2
22
7.3
Download from Www.Somanuals.com. All Manuals Search And Download.
5
GrassTrimmer
Usermanual
Congratulations!
Safety instructions
Your purchase of this Black & Decker Reflex® grass
trimmer and lawn edger assures you of years of
problem free trimming. The Reflex® not only trims
grass and edges the lawn, it also has a unique
totally automatic line feed system. You do nothing -
the Reflex® system means non-stop trimming; by
the use of a simple mechanism it senses when the
line has worn and, when needed, automatically
feeds out line to its optimum cutting length. You
just switch the unit on and trim.
Read all of this manual carefully, observing
all the recommended safety instructions
before, during and after using your machine.
Maintain your machine in good working order.
Familiarise yourself with the controls on
your machine before attempting to operate
it, but above all, be sure you know how to
stop your machine in an emergency.
Retain this manual and all other literature
supplied with your machine for future
reference.
Description
Electricalconnection
Following is a list of the parts that will be mentioned
in this instruction leaflet and are shown in the
appropriatediagrams:
•
Your machine is designed for use on AC
(mains)electricalsuppliesonly. Do not
attempt to use on any other supply.
Body (1)
•
•
•
Plug your machine into a power point,
never in a light socket.
1
Secondaryhandle(2)
Do not leave your machine unattended
whilstitisconnectedtotheelectricalsupply.
Triggerswitch(3)
Switchhandle(4)
Always switch off and remove the plug
from the mains before cleaning,
inspecting or adjusting any part of the
trimmer, or if the supply cord has
becomedamaged orentangled.
Supplycord restraint (5)
Power inlet or supply cord (6)
Edge conversion button (7)
Line trimming blade (8)
Cutting line (9)
Doubleinsulation
Your machine is double insulated. This
means that all external metal parts are
electricallyisolated fromthepowersupply.
This is achieved by placing an extra
insulationbarrierbetweentheelectricaland
mechanicalparts. Doubleinsulationmeans
greaterelectricalsafetyand obviatesthe
necessityofhaving themachineearthed.
Guard (10)
Guard retaining lugs (11)
2
Guard screw (12)
Guard screw hole (13)
Front edge (14)
Spool cover (15)
4
Spool cover tab (16)
Power supply cord
•
•
•
The power supply cord should be
regularly inspected for signs of damage or
ageing and only used if in good condition.
Spool housing (17)
Eyelet (18)
Spool (19)
Always keep the power supply cord
away from the cutting line (9), be aware
of its position at all times.
5
6
7
Arrow (20)
Line retaining hole (21)
Never carry your machine by the cord or
jerk the cord to remove the plug from the
socket. Keep the cord away from heat,
oils and sharp edges.
Lever (22)
•
Havedamaged cordsreplaced
completelybyyournearest Black&Decker
service centre. Do not attempt to do this
yourself as the switch handle is not
customer serviceable.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Cutting line
ENGLISH
•
Take care against injury from line trimming
blade (8) during unpacking and assembly
and any excess line which may be cut
off when the trimmer is first operated.
•
The cutting line (9) will continue to run
for a short time after releasing the
trigger switch. Under no circumstances
should you attempt to stop the cutting
line, always allow it to stop on its own.
•
•
Never use your machine with a
damaged guard (10) or without the guard
fixed inposition.
Be careful when trimming as freshly cut
grass is damp and slippery.
•
Never fit metal cutting line.
Safety of others
Clothing
•
Rememberthat theoperator/useris
responsibleforaccidentsorhazards
occuringtootherpeopleortheirproperty.
•
Always wear safety glasses when using
your machine.
•
To protect your feet, always wear stout
shoes or boots (not bare footed or
wearingopensandals).
•
Never allow children or persons who are
unfamiliar with this type of machine to
use it, nor anyone who has not read
this leaflet.
•
•
Wear long trousers to protect your legs -
any debris left on the lawn or cutting path
may be picked up and ejected by the
cuttingline.
360˚
•
Do not allow children, animals or other
adults near your machine when in use -
always keep them well away from the
cutting area.
6
m
/20ft
Use ear protection if the sound level
seemsuncomfortablewhenusing
yourmachine.
Care of your machine
•
Store your machine in a dry place when
not in use, out of the reach of children.
Using your machine
•
•
•
Always use your machine in the manner
outlined in this manual. Your machine is
designed to be used in an upright
position and if it is used in any other way
an injury may result.
•
Do not use solvents or cleaning fluids
to clean your machine - use a blunt
scraper to remove grass and dirt. Always
disconnect from theelectricalsupplyand
ensure the cutting line (9) is stationary
beforecleaning.
Beforeusing yourmachine, disconnect it
from theelectricalsupplyand visually
inspect the rotating parts for damage.
Also, check that the spool assembly
issecure.
•
•
Do not operate your machine if any parts
aredefective.
Do not attempt to remove any parts
other than those mentioned in these
instructions.
Always check that your lawn or cutting
path is clear of all sticks, stones, wire
and other debris. Contact with such
debris may damage your machine.
•
Use only Black & Decker recommended
replacement partsand accessories.
•
•
Keep your machine away from your feet
and other parts of your body when
switchingonand duringoperation.
Electrical safety
Your machine should always be switched off
at the mains before disconnecting any plug
and socket connector, extensioncables,
orcordsets.
Do not switch on your machine when it is
upsidedown.
•
•
Walk, never run with the unit.
Mains plug replacement - UK only
Do not use your machine in the rain and
do not allow it to get wet.
Should your mains plug need replacing and
you are competent to do this, proceed as
instructed below. If you are in doubt contact
a Black & Decker service centre or a
qualifiedelectrician.
•
•
•
Use your machine only in daylight or
good artificiallight.
Do not cross gravel paths or roads whilst
the cutting line is rotating.
•
•
Disconnect the plug from the supply.
Do not cut excessively steep slopes.
Be sure of your footing and cut across
the face of slopes, never up and down.
Cut off the plug and dispose of it safely,
a plug with bared copper conductors
is dangerous if engaged in a live
socket outlet.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
•
•
Only fit 13 amp BS1363A approved
plugs fitted with the correctly rated fuse.
Warning! The use of an RCD or other circuit
breaker unit does not release the operator of
the machine from the safety instructions and
safe working practices given in this manual.
The cable wire colours, or a letter, will
be marked at the connection points of
most good quality plugs. Attach the
wires to their respective points in the
plug (see below). Brown is for 'Live' (L)
and blue is for 'Neutral' (N).
Extension cables or cordsets
You can use up to 30 metres (100ft) of
extension cord without undue loss of power.
Extensioncordsand cordsetsshould complywith
nationalregulations.
Preparing the trimmer for use
(Fig. 2)
•
Take the trimmer and the guard (10) out
of the box.
2
•
Remove the guard screw (12) which is
located on the underside of the guard
(Fig. 2.1).
240
•
•
Place the guard into the channel on the
trimmerbody(Fig. 2.2).
Push the guard fully home until the guard
is flush with the body (Fig. 2.3).
•
•
Before replacing the top cover of the
mains plug ensure that the cable restraint
is holding the outer sheath of the cable
firmly and that the two leads are correctly
fixed at the terminal screws.
•
•
Replace the guard screw (Fig. 2.4).
If correctly assembled, the guard will now
be secured to your trimmer.
Warning! Neverconnect LiveorNeutral
wires to Earth pin marked E or
•
In transit, the end of the cutting line (9)
is taped to the side of the spool cover.
Please discard the tape to release the
length of line. There should be a
minimum of 9cm (3.5") of cutting line
protruding from thespoolhousing
beforeusingyourtrimmer.
.
Fuse replacement - UK only
Your machine is supplied with cable fitted
withanon-wireableplug.
•
The plug is fitted with a 5 amp fuse
which is the recommended fuse for
yourmachine.
Note: When your machine is operated for
the first time any excess line will be cut off by
the line trimming blade (8) housed in the
guard. This is also the case for any
subsequent lineadjustment. Becauseline
cut off by the blade in the guard may be
ejected, it is important that the amount of
excess line is kept to a minimum. Where an
excessive amount of line is pulled out, the
line should be cut back to the outside of the
guard before switching on your trimmer. Cut
the line off on the trimmer blade by hand.
•
•
Only use replacement fuses which are
approved toBS1362.
When changing the fuse in your plug,
always ensure the fuse cover is refitted.
If the fuse cover is missing or damaged
do not use the plug.
Note: Fuses do not give personal protection
against electric shock.
Increased safety can be obtained by having
aqualified electricianinstallahighsensitivity
(30mA) circuit breaker in the house wiring.
If you do not have such a circuit breaker
installed, or you do not wish to have one
installed, thenwestronglyrecommend that
the electrical power to the machine be
supplied throughahighsensitivityresidual
current device (RCD). The RCD is designed
to provide a high degree of personal
•
Always ensure that the spool cover is
secure before and after use.
How to use your trimmer (Fig. A - J)
In order to get the most from your trimmer please be
sure to follow the techniques shown. Do not be
impatient; you will obtain the best results through
experience and by following these simple rules.
protectionagainst harmfulelectric current
should fault conditions occur.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Do not use your trimmer without
itsguard.
ENGLISH
A
B
Do not cut wet grass; best results are
achieved when the grass is dry.
Trimming
•
The most effective way to use your
trimmer in edging mode is to stand by
the side of it (Fig. 3.2). Guide the front
edge of the trimmer (14) along the lawn
so that the cutting line just trims the
grass overhanging the lawn edge (Fig. H).
•
•
•
To switch on your trimmer, squeeze the
triggerswitch(3).
To switch the unit off, release the
triggerswitch.
To carry the trimmer when not in use,
it is preferred that you use the secondary
handle(2).
Replacement line
Cut at an angle and with the tip of the
cutting line(9).
A new spool containing 10 metres of nylon line may
be purchased from your Black & Decker dealer.
Alternatively, replacement packscontaining25to
50 metres of line are available.
C
D
E
F
Swing the trimmer gently from side to side.
Do not overload the trimmer. It operates best
at high speeds.
For maximum reliability never put on a heavier or
lighter line (eg. fishing line) which will prevent the
automatic feed fromfunctioning, causemotorfailure
orreducecuttingperformance.
On long grass, start at the top and take
smallcuts.
Use the edge of the guard (10) to keep the
trimmer away from hard surfaces and
delicateitems.
G
How to fit a new spool of cutting line
(Fig. 4 & 5)
Edging (GL540)
Best results are achieved on edges greater
than 50mm deep.
•
Disconnect yourtrimmerfrom the
powersupply.
H
J
•
Remove the spool cover by pushing the
2 spool cover tabs (16) inwards and
upwards (Fig. 4), then pull off (it is not
necessary to push both tabs in at the
same time). The empty spool can now
be withdrawn from the drive shaft.
Note: Your trimmer is a maintenance tool for
trimming overhanging grassand should not
be used to create edges. Edges can be
created using an edging spade.
4
5
If your trimmer is for use with a ‘detachable’
cord, loop a length of cord through the cord
restraint (5) to avoid the plug and socket
coming apart accidentally, if the cord is pulled.
•
•
Remove any dirt or grass that may have
collected inside the spool housing and
cover.
Unwind approximately9cm(3.5")of
cutting line (9) from the new spool (19)
and temporarily park the cutting line end
in one of the ‘L’ shaped slots to prevent
thelineunravelling.
How to convert between the
trimming and edging mode (Fig. 3)
In addition to conventional trimming, your
trimmer can be used to trim overhanging
grass along lawn edges and flower beds.
•
Feed the cutting line through the eyelet
and then push the spool onto the centre
drive shaft while pulling the free end of
the line to release it from the ‘L’ shaped
slot. To fully seat the spool, rotate as
necessary, taking care not to trap the
cutting line underneath the spool and
making sure that there is a minimum of
9cm (3.5") protruding from the
To convert your trimmer between the
trimming and edging mode:
3
•
With the trimmer switched off, place one
hand on the switch handle (4) and the
other on the trimmer body (1). Press the
button (7) on the front of the trimmer
body. Keepingthebuttondepressed,
rotatethetrimmerbodyanti-clockwise
and then release the button. Continue to
rotate the trimmer body until it locks into
position (Fig. 3.1).
spoolhousing.
•
Replace the spool cover by aligning
both tabs on it (16) with the slots in the
spool housing and pushing them into
place. Make sure that both tabs are
securelylocated.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Line too short or line jammed on spool
How to wind new line onto an empty
spool (Fig. 6 & 7)
•
•
•
Disconnect your trimmer from the
powersupply.
•
A maximum of 10 metres of new cutting
line can be wound onto the empty spool.
The spool has an ‘Indicator’ to help you
avoid windinganexcessivequantityof
cutting line on the spool, as too much will
prevent theautomatic feed systemfrom
functioning.
Remove the spool cover (15) by pushing
both tabs (16) inwards and upwards (Fig. 4).
6
Lift the spool (19) approximately 6mm (1/4")
from the spool housing (17), while pulling the
cutting line (9). This will allow you to lengthen
the line while clearing any line jammed inside
the spool. Ensure there is a minimum of 9cm
(3.5")protruding from thespoolhousing.
•
•
Remove any remnant of old cutting line
from the spool (19).
•
Rotate the spool as necessary to fully seat
the spool and replace the cover by aligning
both tabs on the cover with the slots in the
spool housing and push into place. Ensure
that both tabs are securely located.
Push the end of the new cutting line into
one of the two retaining holes (21) provided
in the spool (19) and insert 20mm.
•
Bend the cutting line over, pulling it
through the adjacent ‘L’ shaped slot.
The cutting line should now be firmly
anchored to the spool and you may
proceed to wind it on in the direction of
the arrow (20).
Line still jammed on spool or broken inside
spool housing
•
Disconnect the power supply and remove
thecover, aspreviouslydescribed.
•
•
Take time to wind the cutting line on
neatly, in layers. Do not criss cross.
•
Lift out thespool(19)completely, holdingthe
coiled cutting line in place to prevent it
unravelling from the spool (Fig. 7).
When you have wound on sufficient
cutting line, temporarily park it in one of
the ‘L’ shaped slots to prevent the spool
unravelling, ensuring youleavea
•
•
Carefully unwind the cutting line (9) from the
spool until any crossed or trapped loops are
cleared. Rewind thecuttinglineevenly, inthe
direction of the arrow (20) on the spool.
minimum of9cm (3.5")protruding.
•
Fit the spool and spool cover (15) to the
spool housing as described for fitting a
new spool.
Temporarily park the cutting line end in one
of the ‘L’ shaped slots to prevent the spool
unravelling. Ensure you leave a minimum of
9cm(3-Ò*)protruding.
•
•
•
Turn the lever (22) backwards and forwards
to ensure it operates freely.
Care and maintenance
•
For best performance, please keep the cutting
line, spool and air slots in the trimmer body
clean. Use a dry brush or cloth to remove grass,
sap or other dirt.
Remove any dirt or grass that may have
collected inside the spool housing and cover.
Feed the end of the line through the eyelet
and then push the spool into the centre drive
shaft while pulling the free end of the line to
release it from the ‘L’ shaped slot. To fully
seat the spool, rotate as necessary, taking
care not to trap the line underneath the
spool, and making sure that there is a
minimum of 9cm (3.5") of line protruding from
thespoolhousing.
•
Plastic parts may be cleaned by using a mild
soap and a cloth dampened with hot water.
Do not use any type of detergent, cleaner or
solvent whichmight containchemicalswhich
could seriously damage the plastic. Do not spray
yourtrimmerwithwater.
•
Self lubricating bearings are used in your trimmer,
therefore, lubricationisnot required.
•
Finally, replacethecoveraspreviously
described.
Fault finding
Before checking your trimmer for any faults,
disconnect it from the mains.
Protecting the environment
Black & Decker provides a facility for
•
If the trimmer will not start, check that the power
cord is properly connected. If this does not work,
check your power point. Finally, check the fuse
and wiring on the cable extension plug (UK only).
recycling Black & Decker products once
they have reached the end of their working
life. This service is provided free of charge.
To take advantage of this service please
return your product to any authorised repair
agent who will collect them on our behalf.
•
If the automatic line feed fails to operate, it could
be for one of the following reasons:
Download from Www.Somanuals.com. All Manuals Search And Download.
10
ENGLISH
You can check the location of your nearest
authorised repair agent by contacting your local
Black & Decker office at the address indicated in
this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our
after-sales service and contacts are available on the
Internet at: www.2helpU.com.
Other outdoor tools
Black & Decker has a full range of outdoor power
tools that make life in the garden easy. If you would
like further information on the following products,
please contact our Service and Information Centre
(see the address page towards the end of this
manual) or your local Black & Decker retailer.
Guarantee
String trimmers
Chainsaws
Black & Decker is confident of the quality of its
products and offers an outstanding guarantee. This
guarantee statement is in addition to and in no way
prejudices your statutory rights. The guarantee is valid
within the territories of the Member States of the
European Union and the European Free Trade Area.
Cordless shear
Hedgetrimmers
Lawnmowers
Lawnrakers
Leafbusters
If a Black & Decker product becomes defective due
to faulty materials, workmanship or lack of
Shredders
conformity, within 24 months from the date of
purchase, Black & Decker guarantees to replace
defective parts, repair products subjected to fair
wear and tear or replace such products to ensure
minimum inconvenience to the customer unless:
Not all products are available in all countries.
•
•
•
•
The product has been used for trade,
professional or hire purposes;
EC Declaration of conformity
GL544/GL545
The product has been subjected to misuse or
neglect;
The product has sustained damage through
foreign objects, substances or accidents;
Black & Decker declares that these tools
conform to:
Repairs have been attempted by persons other
than authorised repair agents or Black & Decker
service staff.
98/37/EC, 89/336/EEC, 73/23/EEC,
EN 55014, EN 60335, EN 61000,
2000/14/EC, Lawn trimmer, L ≤ 50 cm
Annex VIII, No. 0086
To claim on the guarantee, you will need to submit
proof of purchase to the seller or an authorised
repair agent. You can check the location of your
nearest authorised repair agent by contacting your
local Black & Decker office at the address indicated
in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our
after-sales service and contacts are available on the
Internet at: www.2helpU.com.
B.S.I., HP2 4SQ, United Kingdom
Level of sound pressure, measured according to
2000/14/EC:
LpA
LWA
LWA
(sound pressure) dB(A) 81
(acoustic power) dB(A) 94
(guaranteed)
dB(A) 96
Hand/arm weighted vibration value according to
EN 50144: 4 m/s2
Brian Cooke
Director of Engineering
Spennymoor, County Durham DL16 6JG,
United Kingdom
1-12-2001
Download from Www.Somanuals.com. All Manuals Search And Download.
11
TYP.
1/2
GL544 - GL545
2
4
5
2
6
7
4
10
11
5
9
8
3
23
3
GL540
24
11
12
16
15
17
1
18
19
20
14
13
21
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Australia
Black & Decker (Australia) Pty. Ltd. Tel. 03-8720 5100
20 Fletcher Road, Mooroolbark,
Victoria, 3138
Fax 03-9727 5940
New Zealand
Black & Decker
81 Hugo Johnston Drive
Penrose, Auckland, New Zealand
Tel. 09 579 7600
Fax 09 579 8200
United Kingdom
Black & Decker
210 Bath Road
Slough, Berkshire SL1 3YD
Tel. 01753 511234
Fax 01753 551155
Helpline 01753 574277
07/03
808876-08
Download from Www.Somanuals.com. All Manuals Search And Download.
|