1
2
3
4
15
5
6
14
13
12
11
10
9
8
7
CD601
CD602
Download from Www.Somanuals.com. All Manuals Search And Download.
B
A
21
20 11
7
22
D
3
C
Download from Www.Somanuals.com. All Manuals Search And Download.
12
5
6
8 F
8
13
E
23
15
G
4
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Personal safety
Intended use
Your Black & Decker saw has been designed for sawing wood
and wood products. This tool is intended for consumer use only.
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
Safety instructions
General power tool safety warnings
Warning! Read all safety warnings and all
@
instructions. Failure to follow the warnings and
instructions listed below may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery
operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
f. Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Further safety instructions for all saws
Causes and operator prevention of kickback:
u kickback is a sudden reaction to a pinched, bound or
misaligned saw blade, causing an uncontrolled saw to lift
up and out of the workpiece toward the operator;
u when the blade is pinched or bound tightly by the kerf
closing down, the blade stalls and the motor reaction
drives the unit rapidly back toward the operator;
u if the blade becomes twisted or misaligned in the cut, the
teeth at the back edge of the blade can dig into the top
surface of the wood causing the blade to climb out of the
kerf and jump back toward the operator.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Kickback is the result of saw misuse and/or incorrect operating
procedures or conditions and can be avoided by taking proper
precautions as given below.
Additional power tool safety warnings
a. Maintain a firm grip with both hands on the saw and
position your arms to resist kickback forces. Position
your body to either side of the blade, but not in line
with the blade. Kickback could cause the saw to jump
backwards, but kickback forces can be controlled by the
operator, if proper precautions are taken.
b. When the blade is binding, or when interrupting a cut
for any reason, release the trigger and hold the saw
motionless in the material until the blade comes to a
complete stop. Never attempt to remove the saw from
the work or pull the saw backward while the blade is
in motion or kickback may occur. Investigate and take
corrective actions to eliminate the cause of blade binding.
c. When restarting a saw in the workpiece, centre the
saw blade in the kerf and check that saw teeth are not
engaged into the material. If saw blade is binding, it may
walk up or kickback from the workpiece as the saw is
restarted.
d. Support large panels to minimise the risk of blade
pinching and kickback. Large panels tend to sag under
their own weight. Supports must be placed under the
panel on both sides, near the line of cut and near the edge
of the panel.
e. Do not use dull or damaged blades. Unsharpened or
improperly set blades produce narrow kerf causing
excessive friction, blade binding and kickback.
@
Warning! Additional safety warnings for saws
a. Keep hands away from cutting area and the blade.
Keep your second hand on auxiliary handle, or motor
housing. If both hands are holding the saw, they cannot
be cut by the blade.
b. Do not reach underneath the workpiece. The guard
cannot protect you from the blade below the workpiece.
c. Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth should
be visible below the workpiece.
d. Never hold piece being cut in your hands or across
your leg. Secure the workpiece to a stable platform.
It is important to support the work properly to minimize
body exposure, blade binding, or loss of control.
e. Hold power tool by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a
"live" wire will also make exposed metal parts of the power
tool "live" and give the operator an electric shock.
f. When ripping always use a rip fence or straight edge
guide. This improves the accuracy of cut and reduces the
chance of blade binding.
g. Always use blades with correct size and shape
(diamond versus round) of arbour holes. Blades that
do not match the mounting hardware of the saw will run
eccentrically, causing loss of control.
h. Never use damaged or incorrect blade washers or
bolt. The blade washers and bolt were specially designed
for your saw, for optimum performance and safety of
operation.
f. Blade depth and bevel adjusting locking levers must
be tight and secure before making cut. If blade
adjustment shifts while cutting, it may cause binding and
kickback.
g. Use extra caution when making a "plunge cut" into
existing walls or other blind areas. The protruding blade
may cut objects that can cause kickback.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety instructions for circular saws with outer or inner
pendulum guards and with tow guard
- Risk of accidents caused by the uncovered parts of the
rotating saw blade.
a. Check lower guard for proper closing before each
use. Do not operate the saw if lower guard does not
move freely and close instantly. Never clamp or tie the
lower guard into the open position. If saw is
- Risk of injury when changing the blade.
- Risk of squeezing fingers when opening the guards.
- Health hazards caused by breathing dust developed
when sawing wood, especially oak, beech and MDF.
accidentally dropped, lower guard may be bent. Raise the
lower guard with the retracting handle and make sure it
moves freely and does not touch the blade or any other
part, in all angles and depths of cut.
Saw blades
u Do not use blades of larger or smaller diameter than
recommended. For the proper blade rating refer to the
technical data. Use only the blades specified in this
manual, complying with EN 847-1.
b. Check the operation of the lower guard spring. If the
guard and the spring are not operating properly, they
must be serviced before use. Lower guard may operate
sluggishly due to damaged parts, gummy deposits, or a
build-up of debris.
u Warning! Never use abrasive wheels.
Safety of others
c. Lower guard should be retracted manually only for
special cuts such as "plunge cuts" and "compound
cuts". Raise lower guard by retracting handle and as
soon as blade enters the material, the lower guard
must be released. For all other sawing, the lower guard
should operate automatically.
d. Always observe that the lower guard is covering the
blade before placing saw down on bench or floor. An
unprotected, coasting blade will cause the saw to walk
backwards, cutting whatever is in its path. Be aware of the
time it takes for the blade to stop after switch is released.
u Warning! Wear ear protection when using this tool.
u This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
u Children should be supervised to ensure that they do not
play with the appliance.
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured in
accordance with a standard test method provided by
EN 60745 and may be used for comparing one tool with
another. The declared vibration emission value may also be
used in a preliminary assessment of exposure.
Additional safety instructions for all saws with riving knife
a. Use the appropriate riving knife for the blade being
used. For the riving knife to work, it must be thicker than
the body of the blade but thinner than the tooth set of the
blade.
b. Adjust the riving knife as described in this instruction
manual. Incorrect spacing, positioning and alignment can
make the riving knife ineffective in preventing kickback.
c. Always use the riving knife except when plunge
cutting. Riving knife must be replaced after plunge
cutting. Riving knife causes interference during plunge
cutting and can create kickback.
d. For the riving knife to work, it must be engaged in the
workpiece. The riving knife is ineffective in preventing
kickback during short cuts.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the
trigger time.
e. Do not operate the saw if riving knife is bent. Even a
light interference can slow the closing rate of a guard.
Residual risks
The following risks are inherent to the use of saws:
- Injuries caused by touching the rotating parts
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These are:
Labels on tool
The following pictograms are shown on the tool:
Warning! To reduce the risk of injury, the user must
- Impairment of hearing.
:
read the instruction manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
u Insert a screwdriver into the hole (16) to prevent the saw
blade from rotating.
Electrical safety
u Securely tighten the blade retaining screw by turning it
clockwise using the spanner (14) supplied.
u Adjust the riving knife as described below.
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
#
Warning! Whenever a new blade is fitted the saw blade guard
should be checked to ensure that it can move freely.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Removing and fitting a saw blade (fig. B)
Caution! This method is for changing blades that do not
contain a hole (16) for the purpose of locking the blade whilst
fitting and removing.
Features
1. On/off switch
2. Lock-off button
3. Main handle
Removing
4. Secondary handle
5. Mitre angle scale
6. Locking knob for mitre angle adjustment
7. Parallel fence
u Set the depth of cut on the saw to 10mm.
u Place a plank of wood on the floor, then place the saw
onto the leading edge of the wood as shown in fig B to
prevent the blade from turning.
8. Shoe
u Whilst applying firm pressure on the saw, loosen and
remove the blade retaining screw (17) by turning it
counterclockwise using the spanner (14) supplied.
u Remove the outer washer (18).
9. Saw blade
10. Saw blade guard
11. Riving knife
12. Depth of cut scale
13. Locking knob for depth of cut adjustment
14. Spanner
u Remove the saw blade (9).
Fitting
15. Saw dust outlet
u Place the saw blade onto the inner washer (19), making
sure that the arrow on the blade points in the same
direction as the arrow on the tool.
u Fit the outer washer (18) on the spindle, with the raised
part pointing away from the saw blade.
Assembly
Warning! Before attempting any of the following operations,
make sure that the tool is switched off and unplugged and that
the saw blade has stopped.
u Insert the blade retaining screw (17) into the hole loosely
tighten by hand.
u Place a plank of wood on the floor, then place the saw
onto the leading edge of the wood as shown in fig B to
prevent the blade from turning.
Removing and fitting a saw blade (fig. A)
Caution! This method for changing the blade is only for use
with blades that contain a hole (16) for the purpose of locking
the blade whilst fitting and removing.
u Whilst applying firm pressure on the saw, securely tighten
blade retaining screw (17) by turning it clockwise using the
spanner (14) supplied.
Removing
u Insert a screwdriver into the hole (16) to prevent the saw
blade from rotating.
u Adjust the riving knife as described below.
u Loosen and remove the blade retaining screw (17) by
turning it counterclockwise using the spanner (14) supplied.
u Remove the outer washer (18).
Warning! Whenever a new blade is fitted the saw blade guard
should be checked to ensure that it can move freely.
u Remove the saw blade (9).
Adjusting the riving knife (fig. C)
The riving knife prevents the saw blade from jamming during
rip sawing operations. The riving knife must be adjusted after
replacing the saw blade.
u Loosen the screw (20) holding the riving knife in position.
u Position the riving knife (11) as shown.
The distance between the toothed rim and the riving knife
should be 2 - 3 mm.
Fitting
u Place the saw blade onto the inner washer (19), making
sure that the arrow on the blade points in the same
direction as the arrow on the tool.
u Fit the outer washer (18) on the spindle, with the raised
part pointing away from the saw blade.
u Insert the blade retaining screw (17) into the hole.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
The height difference between the toothed rim and the lower
end of the riving knife should be 2 - 3 mm.
u Tighten the screw.
u Insert the dust extraction adaptor (23) into the saw dust
outlet (15).
u Connect the vacuum cleaner hose to the adaptor.
Fitting and removing the parallel fence (fig. D)
The parallel fence is used to saw in a straight line parellel to
the edge of the workpiece.
Hints for optimum use
u As some splintering along the line of cut on the top side of
the workpiece cannot be avoided, cut on the side where
splintering is acceptable.
Fitting
u Where splintering is to be minimised, e.g. when cutting
laminates, clamp a piece of plywood onto the top of the
workpiece.
u Loosen the locking knob (21).
u Insert the parallel fence (7) through the openings (22).
u Slide the parallel fence into the desired position.
u Tighten the locking knob.
Accessories
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to
high quality standards and designed to enhance the
performance of your tool. By using these accessories you will
get the very best from your tool.
Removing
u Loosen the locking knob (21).
u Pull the parallel fence off the tool.
Use
This tool can be used in the right hand or the left hand.
Maintenance
Your Black & Decker corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Adjusting the depth of cut (fig. E)
The depth of cut should be set according to the thickness of
the workpiece. It should exceed the thickness by approx. 2 mm.
u Loosen the knob (13) to unlock the saw shoe.
u Move the saw shoe (8) into the desired position. The
corresponding depth of cut can be read from the scale (12).
u Tighten the knob to lock the saw shoe in place.
Warning! Before performing any maintenance on corded/
cordless power tools:
u Switch off and unplug the appliance/tool.
u Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
u Or run the battery down completely if it is integral and then
switch off.
u Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
Adjusting the mitre angle (fig. F)
This tool can be set to mitre angles between 0° and 45°.
u Loosen the locking knob (6) to unlock the saw shoe.
u Move the saw shoe (8) into the desired position. The
corresponding mitre angle can be read from the scale (5).
u Tighten the locking knob to lock the saw shoe in place.
Switching on and off
u Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
u Regularly open the chuck and tap it to remove any dust
from the interior (when fitted).
u To switch the tool on, move the lock-off button (2) into the
unlock position and squeeze the on/off switch (1).
u To switch the tool off, release the on/off switch.
Sawing
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
u Safely dispose of the old plug.
u Connect the brown lead to the live terminal in the new plug.
u Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
u Always hold the tool with both hands.
u Let the blade run freely for a few seconds before starting
the cut.
u Apply only a gentle pressure to the tool while performing
the cut.
u Work with the shoe pressed against the workpiece.
Dust extraction (fig. G)
An adaptor is required to connect a vacuum cleaner or dust
extractor to the tool. The adaptor can be purchased from your
local Black & Decker retailer.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Protecting the environment
EC declaration of conformity
MACHINERY DIRECTIVE
Separate collection. This product must not be
disposed of with normal household waste.
Z
%
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
CD601/CD602
Black & Decker declares that these products described under
"technical data" are in compliance with:
2006/42/EC, EN 60745-1, EN 60745-2-5
Separate collection of used products and packaging
z
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand for
raw materials.
For more information, please contact Black & Decker at the
following address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of Black & Decker.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Kevin Hewitt
Vice-President Global Engineering
Black & Decker Europe, 210 Bath Road, Slough,
Berkshire, SL1 3YD
_
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
United Kingdom
04/10/2011
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
Technical data
CD601 TYPE 3 CD602 TYPE 3
Input voltage
Power input
No-load speed
Max. depth of cut
Blade diameter
Blade bore
VAC 230
230
1,150
5,500
55
170
16
W
1,100
min-1 5,500
mm 55
mm 170
mm 16
mm 2.6
kg 4.7
Blade tip width
Weight
2.6
4.7
Level of sound pressure according to EN 60745:
Sound pressure (LpA) 93.5 dB(A), uncertainty (K) 3 dB(A)
Acoustic power (LWA) 104.5 dB(A), uncertainty (K) 3 dB(A)
Vibration total values (triax vector sum) according to EN 60745:
Vibration emission value (ah) 2.0 m/s2, uncertainty (K) 1.5 m/s2
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24 months
from the date of purchase, Black & Decker guarantees to
replace defective parts, repair products subjected to fair wear
and tear or replace such products to ensure minimum
inconvenience to the customer unless:
u The product has been used for trade, professional or hire
purposes;
u The product has been subjected to misuse or neglect;
u The product has sustained damage through foreign
objects, substances or accidents;
u Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-sales
service and contacts are available on the Internet at:
register your new Black & Decker product and to be kept up to
date on new products and special offers. Further information
on the Black & Decker brand and our range of products is
available at www.blackanddecker.co.uk
Download from Www.Somanuals.com. All Manuals Search And Download.
11
TYP.
CD601 - CD602
1-2-3
36
37
43
38
39
44
41
42
7
4
5
6
1
8
2
3
10
69
11
12
13
17
21
73
26
45
9
22
20
71
16
23
70
29
1
48
18
19
46
14
15
3
30
27 28
24
72
47
25
50
31
74
51
33
34
35
49
53
64
63
52
62
68
32
61
65
55
54
56
58
59
66
57
67
60
Download from Www.Somanuals.com. All Manuals Search And Download.
11 - 10 - 11
E13688
Download from Www.Somanuals.com. All Manuals Search And Download.
13
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
Do not forget to register your product!
Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product
code to Black & Decker in your country.
Download from Www.Somanuals.com. All Manuals Search And Download.
Australia
Black & Decker (Australia) Pty. Ltd.
20 Fletcher Road, Mooroolbark,
Victoria, 3138
Tel. 03-8720 5100
Fax 03-9727 5940
New Zealand
Black & Decker
5 Te Apunga Place
Mt Wellington
Tel. +64 9 259 1133
Fax +64 9 259 1122
Auckland 1060
United Kingdom
Black & Decker
210 Bath Road
Tel. 01753 511234
Fax 01753 551155
Helpline 01753 574277
Slough, Berkshire SL1 3YD
90580808 REV 0
10/2011
Download from Www.Somanuals.com. All Manuals Search And Download.
|