FSMH1621S
FSMH16151
Download from Www.Somanuals.com. All Manuals Search And Download.
F
H
J
G
I
3
Download from Www.Somanuals.com. All Manuals Search And Download.
K
L
M
N
O
4
Download from Www.Somanuals.com. All Manuals Search And Download.
(Original instructions)
ENGLISH
Attaching the hand held steam cleaner (Fig. C)
u Holding the back of the steam mop body (9) Push the
hand held steam cleaner (5) firmly into the steam mop
body (9) until it clicks into place.
Caution! Always ensure the handle command lights up to
confirm the unit is docked.
Intended use
Your BLACK+DECKER steam mop has been designed for
sanitising and cleaning sealed hardwood, sealed laminate,
linoleum, vinyl, ceramic tile, stone and marble floors and for
refreshing carpets. This appliance is intended for indoor
household use only.
Warning! Inspect that the seal (26 Fig. J) on the steam nozzle
(4) before fitting the hand held steam mop to the steam mop
body. If the seal is missing or damaged then please contact
your nearest authorised repair agent. Do not use the appli-
ance.
Warning! Read all of the 'Safety, Maintenance,
Service' manual carefully before operating
this appliance.
Read all of this manual carefully before operating
the appliance.
Removing the hand held steam cleaner (Fig. C)
u Push the release button (20) down and pull the hand held
steam cleaner (5) away from the steam mop body
Features
This appliance includes some or all of the following features.
1. ON/Off switch
2. Lock off button
3. Trigger switch
4. Steam nozzle
5. Hand held steam cleaner
6. AutoselectTM button
7. Filler cap
8. Water tank
9. Steam mop body
10. Handle
Attaching a cleaning pad (Fig. D)
Replacement cleaning pads are available from your
BLACK+DECKER dealer:
Steam head cleaning pad (12) - cat. no. FSMP20-XJ).
u Place a cleaning pad (12) on the floor with the ‘hook &
loop’ side facing up.
u Lightly press the steam mop down onto the cleaning pad
(12).
Caution! Always place your steam mop with the handle (10)
in the upright position when stationary and make sure the
steam mop is turned off when not in use.
11. Steam head
12. Steam head cleaning pad
14. Carpet glider
15. Bottom cable tidy hook
16. Top cable tidy hook
17. Cable management clip
Removing a cleaning pad (Fig. E)
Caution! Always wear suitable shoes when changing the
cleaning pad on your steam mop. Do not wear slippers or
open toed footwear.
u Return the handle (10) to the upright position and turn the
steam mop ‘OFF’.
Assembly
Warning! Before attempting any of the following operations,
make sure that the appliance is switched off and unplugged
and that the appliance is cold and does not contain any water.
u Wait until the steam mop cools down. (approximately five
minutes)
u Place the front of your shoe onto the cleaning pad removal
tab (21) and press down firmly.
u Lift the steam mop up off the cleaning pad.
Caution! Always place your steam mop with the handle (10)
in the upright position when stationary and make sure the
steam mop is turned off when not in use.
Attaching the handle (Fig. A)
u Slide the bottom end of the handle (10) into the top end of
the steam mop body (9) until it clicks into place. The arrow
on the handle (10) should be aligned with the top of the
steam mop body (9).
Attaching the steam head (Fig. B)
u Slide the bottom end of the steam mop body (9) onto the
Filling the water tank (Fig. F)
This Steam cleaner incorporates an anti-calc system to help
prolong the life of the system.
Note: Fill the water tank with clean tap water.
Note: In areas of very hard water, the use of de-ionised water
is recommended.
steam head (11) until it clicks into place.
u The steam head can be removed from the Steam mop
body by pressing the steam head release button (19) and
pulling the steam mop body (9) off the steam head (11).
u Open the filler cap (7) by flipping it down.
u Fill the water tank (8) with water.
Warning! Your water tank has a 0.36 litre capacity.
u Re-fit the filler cap (7).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
(Original instructions)
ENGLISH
Note: Ensure the filler cap is firmly secured.
Note: Do not use chemical cleaners with your steam mop..
Attaching the variable steam jet nozzle (Fig. L)
u Press in the clips (30) on either side of the variable steam
jet nozzle (31).
Attaching the carpet glider (Fig. G) (For use on
carpets only)
u Press the variable steam jet nozzle onto the steam nozzle
(4) or the hose (27) and release the clips (30).
u Place carpet glider on the floor.
u Attach a cleaning pad to the unit.
Important! Ensure that the variable steam jet nozzle (31) is
securely fastened before using the hand held steam cleaner.
If steam escapes from the joint then the variable steam jet
nozzle is not correctly fit, allow the unit to cool then remove
and re-fit the variable steam jet nozzle.
u Lightly press the steam mop down onto the carpet glider
(14) until it clicks into place.
Caution! Always place your steam mop with the handle (10)
in the upright position when stationary and make sure the
steam mop is turned off when not in use.
Attaching other accessories (Fig. J)
u Align the lugs on the hose with the recesses on the acces-
sory.
Removing the carpet glider (Fig. G)
Caution! Always wear suitable shoes when changing the
carpet glider on your steam mop. Do not wear slippers or
open toed footwear.
u Return the handle (10) to the upright position and turn the
steam mop ‘OFF’.
u Press the accessory (29) onto the hose (27) and twist
anti-clockwise until the accessory clicks into place.
Note! The variable steam jet nozzle may be used without the
hose by fitting them directly to steam nozzle. All other acces-
sories must be connected to the hose for use.
u Wait until the steam mop cools down. (approximately five
minutes)
u Place the front of your shoe onto the carpet glider removal
tab (22) and press down firmly.
u Lift the steam mop up off the carpet glider (14).
Caution! Always place your steam mop with the handle (10)
in the upright position when stationary and make sure the
steam mop is turned off when not in use.
Removing the hose and accessories(Fig. K & L)
Warning! The Steam nozzle, variable steam jet nozzle, hose
and accessories become hot during use. Allow the unit and all
accessories to cool before removing any accessories.
Removing an accessory (Fig. K)
u Twist the accessory (29) clockwise then pull away from
the hose (27).
Fitting a scent pack (Fig. I & J)
Warning! Return the handle (10) to the upright position and
turn the steam mop ‘OFF’. Wait until the steam mop cools
down. (approximately five minutes).
Removing the hose (Fig. K)
u Press in the clips (29) on either side of the hose (27) and
pull away from the steam nozzle (4).
u Slide the door release button (35), the door will open.
u Place the scent pack into the cavity (36).
Removing the variable steam jet nozzle (Fig. L)
u Close the door (37) py pushing it firmly down.
u Press in the clips (30) on either side of the variable steam
jet nozzle (31) and pull away from the steam nozzle (4).
Attaching the hose and accessories to the Hand
held steam cleaner (Fig. K & L)
Warning! Inspect the seal (26) on the steam nozzle (4) and
hose (27) before each use. If the seal is missing or damaged
then please contact your nearest authorised repair agent. Do
not use the appliance.
Use
Important! This unit will kill 99.9% of bacteria & germs when
used in accordance with this manual and with the micro fibre
pad fitted and a continuous run time of 90 seconds.
Switching on and off (Steam mop)
Attaching the hose (Fig. K)
u To switch the appliance on, press the ON/OFF button (1).
It takes approximately 15 seconds for the steam mop to
heat up.
Note: When the steam mop is first turned on the water res-
ervoir will glow red. Once the steam mop is ready to use the
water reservoir will glow blue.
u Press in the clips (28) on either side of the hose (27).
u Press the hose (27) onto the steam nozzle (4) and release
the clips (28).
Important! Ensure that the hose (27) is securely fastened
before using the hand held steam cleaner. If steam escapes
from the joint then the hose is not correctly fit, allow the unit to
cool then remove and re-fit the hose.
u To switch the appliance off, press the ON/OFF button (1).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
(Original instructions)
ENGLISH
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (10) in the upright position when stationary
and make sure the steam mop is turned off when not in use.
Caution! Always empty the steam mop after use.
Caution! Steam may continue to be produced for a short time
after the trigger switch (3) is released, this is normal. Switch
off and allow the unit to cool before removing any accessories.
Hints for optimum use
Note: When first filled or after running dry it can take up to 45
seconds for steam to be produced.
General
Caution! Never use the steam mop without first attaching a
cleaning pad.
u During steam mop use you can use the cable manage-
ment clip (17) to keep your cable out of the way of the
work area..
u Always vacuum or sweep the floor before using the steam
mop.
u The easiest way to use the machine is to tilt the handle to
a 45˚ angle and clean slowly, covering a small area at a
time.
u Do not use chemical cleaners with your steam mop. To
remove stubborn stains from vinyl or linoleum floors, you
can use the steam burst button to apply extra steam to
the area or pre-treat with a mild detergent and some water
before using the steam mop.
TM
Autoselect Technology (Fig. I)
This steam mop is fitted with an AutoselectTM button (6)
which shows various cleaning applications. They are used to
select the correct operating mode for your particular cleaning
operation.
Using AutoselectTM , choose from one of the following applica-
tions by pressing the autoselect button (6) until the required
setting is selected:
Wood/Laminate
Stone/Marble
Tiles/Vinyl
Steam cleaning with the mop
u Fit hand held steam cleaner (5) to the steam mop body
(9).
u Place a cleaning pad (12) on the floor with the ‘hook &
loop’ side facing up.
u Lightly press the steam mop down onto the cleaning pad
(12).
The steam mop will select the correct volume of steam
required for your particular cleaning operation.
Note: Always check you are using the correct setting before
using your steam mop. For convenience the steam mop will
remember the last setting you chose.
u Connect the steam mop to the mains.
u Press the ON/OFF button (1). It takes approximately 15
seconds for the steam mop to heat up.
Steam burst (Fig. I)
The steam mop is equipped with a steam burst button to aid in
the removal of stubborn marks and stains.
u During use, press the steam burst button (25) to apply
extra cleaning power.
Note: The steam burst will last for 10 seconds then the steam
mop will return to the chosen setting.
u Press the AutoselectTM button (6) till the required setting is
reached.
u Pulling the handle (10) back will activate the steam pump.
After a few seconds steam will start to come out of the
steam head.
Note: When first filled or after running dry it can take up to 45
seconds for steam to be produced.
u It takes a few seconds for steam to enter the cleaning pad.
The steam mop will now glide easily over the surface to be
sanitised/cleaned.
Switching on and off (Hand held steam cleaner)
(Fig. M)
u To switch the appliance on, press the ON/OFF button (1).
It takes approximately 15 seconds for the hand held steam
cleaner to heat up.
Note: When the hand held steam cleaner is first turned on
the water reservoir will glow red. Once the hand held steam
cleaner is ready to use the water reservoir will glow blue.
u Lift the lock off switch (2) and pull the trigger switch (3).
After a few seconds steam will be produced.
u To switch the appliance off, release the trigger switch (3)
then press the ON/OFF button (1).
u Push and pull the steam mop slowly across the floor to
thoroughly steam clean each section.
Note: During use you may turn off the steam pump by return-
ing the handle to the upright position, this convenient feature
will allow you to leave the steam mop for a short time so that
you may move items of furniture, then continue cleaning
without the need to switch the appliance off.
Caution! Always empty the hand held steam cleaner after
use.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
(Original instructions)
ENGLISH
Caution! It is important to monitor the water level in the water
tank. To refill the water tank and continue to sanitise/clean, re-
turn the handle (10) to the upright position and turn the steam
mop ‘OFF’. Unplug the unit from the electrical wall outlet, refill
the water tank (8).
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (10) in the upright position when stationary
and make sure the steam mop is turned off when not in use.
u When you have finished using the steam mop, return the
handle (10) to the upright position and turn it ‘OFF’ and
wait until the steam mop cools down. (approximately five
minutes)
Caution! It is important to monitor the water level in the water
tank. To refill the water tank and continue to sanitise/clean, re-
turn the handle (10) to the upright position and turn the steam
mop ‘OFF’. Unplug the unit from the electrical wall outlet, refill
the water tank (8).
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (10) in the upright position when stationary
and make sure the steam mop is turned off when not in use.
After use (Fig. N & O)
u Return the handle (10) to the upright position and turn the
steam mop ‘OFF’,
u Wait until the steam mop cools down. (approximately five
minutes)
Carpet refreshing
u Unplug the steam mop from the electrical wall outlet.
u Empty the water tank (8).
u Place a cleaning pad (12) on the floor with the ‘hook &
loop’ side facing up.
u Remove the cleaning pad (12) and wash it ready for
next use. (Take care to follow the wash care instructions
printed on the cleaning pad).
u Lightly press the steam mop down onto the cleaning pad
(12).
u Place the carpet glider (14) on the floor.
u Wrap the supply cable around the cable tidy hooks (15 &
16).
u Lightly press the steam mop down onto the carpet glider
(14) until it clicks into place.
Note: The top cable tidy hook (16) rotates to easily release
the cable ready for next use.
u Clip the supply cable onto itself using the cable tidy clip
(32) close to the plug.
Note: With the handle (10) in the upright position, the cable
neatly wrapped around the cable tidy hooks (15 & 16) and
secured with the cable tidy clip (32) your steam mop will stand
on its own for storage. Alternatively there is a hanging bracket
(33) built into the hand grip (34) which will allow your steam
mop to be hung from a suitable hook on the wall. Always
ensure that your wall hook is capable of supporting the weight
of the steam mop safely.
u Connect the steam mop to the mains.
u Press the ON/OFF button (1). It takes approximately 15
seconds for the steam mop to heat up.
u Press the AutoselectTM button (6) to the Wood/Laminate
setting.
u Pulling the handle (10) back will activate the steam pump.
After a few seconds steam will start to come out of the
steam head.
Note: When first filled or after running dry it can take up to 45
seconds for steam to be produced.
u Push and pull the steam mop slowly across the carpet to
thoroughly refresh each section.
Note: During use you may turn off the steam pump by return-
ing the handle to the upright position, this convenient feature
will allow you to leave the steam mop for a short time so that
you may move items of furniture, then continue cleaning
without the need to switch the appliance off.
u When you have finished using the steam mop, return the
handle (10) to the upright position and turn it ‘OFF’ and
wait until the steam mop cools down. (approximately five
minutes)
Caution! If steam is observed escaping from the join between
the hand held steam cleaner and the steam mop body, switch
off and disconnect the unit from the mains supply. Allow to
cool. Remove the hand held steam cleaner from the steam
mop body. Inspect the seal (26) on the steam nozzle (4) and
hose (27) (fig. K). If the seal is missing or damaged then
please contact your nearest authorised repair agent. Do not
use the appliance. If the seal is in good condition re-fit the
hand held steam cleaner to the steam mop body ensuring that
it is seated firmly in place.
Hand held steam cleaning
u Attach the required accessory.
u Connect the hand held steam cleaner to the mains.
u Press the ON/OFF button (1). It takes approximately 15
seconds for the hand held steam cleaner to heat up.
u Lift the lock off (2) and pull the trigger switch (3) to activate
the steam pump. After a few seconds steam will start to
come out of the accessory.
Note: When first filled or after running dry it can take up to 45
seconds for steam to be produced.
Note: During use you may turn off the steam pump by releas-
ing the trigger switch, this convenient feature will allow you to
place the hand held steam cleaner down for a short time so
that you may move items of furniture, then continue cleaning
without the need to switch the appliance off.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
(Original instructions)
ENGLISH
u When you have finished using the hand held steam
cleaner, release the trigger switch (3), turn it ‘OFF’ and
disconnect from the mains supply. Wait until the steam
mop cools down before storing. (approximately five
minutes)
Caution! It is important to monitor the water level in the water
tank. To refill the water tank and continue to sanitise/clean,
turn the hand held steam cleaner ‘OFF’. Unplug the unit from
the electrical wall outlet, refill the water tank (8).
Problem
Step
4
Possible solutions
Check that the handle (10) of the steam mop
is pushed firmly into the steam mop body (9).
Check that the arrow on the handle is flush
with the top of the steam mop body (9).
The digital controls
do not light up.
Check that the hand held steam cleaner (5)
is firmly docked into the steam mop body (9).
5
6
7
Check steps 1, then 2, then 3.
Caution! Steam may continue to be produced for a short time
after the trigger switch (3) is released, this is normal. Switch
off and allow the unit to cool before removing any accessories.
The steam mop will only produce steam
once the handle is pulled back from the
upright position.
The steam mop is
not producing
steam.
8
Check that the water tank (8) is full.
NOTE: When first filled or after running dry it
can take up to 45 seconds for steam to be
produced.
Accessories
The performance of your appliance depends on the accessory
used. BLACK+DECKER accessories are engineered to high
quality standards and designed to enhance the performance
of your appliance. By using these accessories you will get the
very best from your appliance.
Check that the Steam head (11) is firmly
docked into the steam mop body (9).
9
10
Check steps 5, then 1, then 2, then 3.
Technical data
The digital controls 11
go out during use.
Check steps 4, then 5, then 1, then 2, then 3
FSMH1621S
FSMH16151
(Type 1)
(Type 1)
The steam mop
stops producing
steam during use.
12
Check steps 7, then 8, then 9, then 5, then 3.
Voltage
Vac
W
230
1600
350
3.6
230
1600
350
3.6
Power
The steam mop has 3 settings. Press the
autoselect button (6) to reduce the amount of
steam being produced.
The steam mop is
producing too
much steam during
use.
13
Tank capacity
ml
Check that the steam burst button (25) has
not been pressed.
14
15
Weight
kg
The steam mop has 3 settings. Press the
autoselect button (6) to increase the amount
of steam being produced.
Troubleshooting
The steam mop is
producing too little
steam during use.
If your appliance seems not to operate properly, follow the
instructions below. If this does not solve the problem, please
contact your local BLACK+DECKER repair agent.
Press the steam burst button (25) to
16
17
temporarily increase the amount of steam.
Problem
Step
1
Possible solutions
The hand held steam cleaner has a lock off
feature. Lift the lock off switch (2) and pull
the trigger switch (3). After a few seconds
steam will be produced.
No steam is being
produced from the
hand held steam
cleaner when the
trigger is pulled.
Check the unit is plugged in at the wall
socket.
The steam mop is
not turning on.
Check the unit is switched on using the on/
off switch (1).
2
3
18
19
Check steps 8, then 1, then 2, then 3.
Check the fuse in the plug.
The hand held steam cleaner will begin to
produce steam after 15 seconds and will
reach maximum steam flow after 45
seconds.
The hand held
steam cleaner is
producing too little
steam during use.
Firmly press the hand held steam cleaner
release button (20) down, then pull the hand
held steam (5) cleaner from the steam mop
body (9).
The hand held
steam cleaner will
not come out from
the steam mop
body.
20
9
Download from Www.Somanuals.com. All Manuals Search And Download.
(Original instructions)
ENGLISH
Problem
Step
21
Possible solutions
Refer to the assembly chapter of the manual
for correct fitting instructions of all parts and
accessories.
The accessories
keep falling off the
unit.
Refer to the assembly chapter of the manual
for correct fitting instructions of all parts and
accessories.
Steam is escaping
from unexpected
areas of the unit.
22
23
Where can I get
further information
/ accessories for
my steam mop.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Australia
Black & Decker (Australia) Pty. Ltd.
20 Fletcher Road, Mooroolbark,
Victoria, 3138
Tel.
Fax
03-8720 5100
03-9727 5940
New Zealand
Black & Decker
5 Te Apunga Place
Mt Wellington
Tel.
Fax
+64 9 259 1133
+64 9 259 1122
Aukland 1060
United Kingdom &
Republic Of Ireland
Black & Decker
210 Bath Road
Tel.
Fax
01753 511234
01753 512365
Slough, Berkshire SL1 3YD
90615612 REV-0
06/2014
Download from Www.Somanuals.com. All Manuals Search And Download.
|