AC504A-WP
Mini-Cat5 Extender
Wallplate Transmitter
Transmit VGA, Component Video (YpbPr), or
Composite Video via UTP Twisted Pair Cable
Order toll-free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday: 877-877-BBOX
FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
CUSTOMER
SUPPORT
INFORMATION
Web site: www.blackbox.com
•
E-mail: [email protected]
UMA1111
Rev. 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Mini-Cat5 Extender Wallplate Transmitter
Trademarks Used in this Manual
BLACK BOX and its logo
are registered trademarks of Black Box
Corporation. Any other trademarks mentioned in this manual are
acknowledged to be the property of the trademark owners.
FCC and Canadian Dept of Communications Radio
Frequency interference statements
This equipment generates, uses, and can radiate radio frequency energy
and if not installed and used properly, that is, in strict accordance with
the manufacturer’s instructions, may cause interference to radio
communication. It has been tested and found to comply with the limits
for a Class A computing device in accordance with the specifications in
Subpart B of Part 15 of FCC rules, which are designed to provide
reasonable protection against such interference when the equipment is
operated in a commercial environment. Operation of this equipment in
a residential area is likely to cause interference, in which case the user
at there own expense will be required to take whatever measures may
be necessary to correct the interference. Changes or modifications not
expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This digital apparatus does not exceed the Class A limits for radio
noise emission from digital apparatus set out in the Radio Interference
Regulation of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de la classe
A prescrites dans le Règlement sur le brouillage radioélectrique publié
par le ministère des Communications du Canada.
European Union Declaration of Conformity
This product complies with the requirements of the European EMC
directive 89/336/EEC
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Model AC504A-WP
Normas Oficiales Mexicanas (NOM)
Electrical Safety Statement
INSTRUCCIONES DE SEGURIDAD
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el
aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia
futura.
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación
deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca de la tina
de baño, lavabo, sótano mojado o cerca de una alberca, etc.
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean
recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea
recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá a lo
descrito en las instrucciones de operación. Todo otro servicio deberá ser referido a
personal de servicio calificado.
9. El aparato eléctrico debe ser situado de tal manera que su posición no interfiera su
uso. La colocación del aparato eléctrico sobre una cama, sofá, alfombra o superficie
similar puede bloquea la ventilación, no se debe colocar en libreros o gabinetes que
impidan el flujo de aire por los orificios de ventilación.
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor como
radiadores, registros de calor, estufas u otros aparatos (incluyendo amplificadores)
que producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo
descrito en el instructivo de operación, o como se indique en el aparato.
12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del
equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados
ni pellizcados por objetos colocados sobre o contra ellos, poniendo particular
atención a los contactos y receptáculos donde salen del aparato.
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las recomendaciones
del fabricante.
15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas de
energia.
16. El cable de corriente deberá ser desconectado del cuando el equipo no sea usado por
un largo periodo de tiempo.
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados
sobre la cubierta u orificios de ventilación.
18. Servicio por personal calificado deberá ser provisto cuando:
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro del aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra un cambio en su desempeño; o
E: El aparato ha sido tirado o su cubierta ha sido dañada.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Mini-Cat5 Extender Wallplate Transmitter
Contents
1. Introduction .......................................................................................4
1.1 General.........................................................................................4
2. Installation .........................................................................................5
2.1 Setup Connections .......................................................................5
2.2 Video Compensation Adjustment................................................7
2.3 Configuration for Composite Video and Stereo Audio ...............8
3. Troubleshooting.................................................................................9
4. Specifications...................................................................................10
5. Appendix .........................................................................................11
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Model AC504A-WP
1. Introduction
1.1 General
The AC504A-WP is used to send PC Video or analog HDTV
(component video) on UTP (Cat5/5e/6) cables. Power is also
transmitted on the same Cat5 cable between the sender unit and the
receiver.
The AC504A-WP can extend the video up to 500 feet. The unit can
support the following video signals
¾
¾
PC’s VGA video (RGBHV) at any resolution
Component video (Y Pb Pr, or RGB), at any resolution - an
adapter cable HD15-to-3RCA will be required
¾
NTSC, PAL, or SECAM Composite video and stereo audio -an
adapter cable HD15-to-3RCA (video and R/L Audio) will be
required
At the receiving (remote) end the Cat5 signal is converted back to
VGA for connection to monitors, projector or other display devices
using a compatible unit (Black Box Model AC602A).
The AC504A-WP includes a power supply that powers itself and the
AC602A Receiver (power-over-UTP) for a clean and easy setup
(Note that if the length of Cat5 cable is longer than 300 feet, the
receiver may require its own power supply).
Alternatively, the power supply can be connected to the AC602A
remote receiver, in which case, the sender is powered through the cat5
cable.
Figure 1 – Connection Block Diagram
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Mini-Cat5 Extender Wallplate Transmitter
1.2 Features
•
•
•
•
•
•
Extends high resolution video with no loss to 500 feet
Differential signaling eliminates ground loops and noise
Handles resolutions up to 1600x1200 at any refresh rate
Slim single gang wall plate design
Reliable and economical
Only one end requires power in most applications. Power supply
can be connected at the sending or the receiving end, whichever is
convenient.
•
•
Drive standard CAT5 cables to 500 feet (for VGA and Component
Video) or to 1200 feet (for Composite Video + Audio)
2. Installation
Figure 2 – AC504A-WP Front
2.1 Setup Connections
1. Connect the VIDEO INPUT to the computer's video port using a
male-male VGA cable (not included).
2. Using Category 5 cables connect the RJ45 port of the Transmitter
located on rear of the unit to the Model AC602A Receiver (not
included).
3. Connect the Remote displays to the VGA output port of the
AC602 Receiver.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Model AC504A-WP
4. Plug in the supplied Power supply to the
Power Input jack on the rear of the sender
unit.
On the rear of the unit next to the RJ45
connector, there is a 2 pin screw terminal
for power connection.
You need to connect 9 vDC to these
terminals.
In your package there is either of the 2
power supplies pictured. There is also a
2.5 mm Jack included in the package so
that you don’t have to cut the connector at the end of the supply. If
you decide to cut off the connector on the end of the power supply,
then use the enclosed jack and solder a pair of wires to it and
connect those to the AC504A-WP or AC602.
Using the supplied 2.5mm Jack also gives you the ability to place
the power supply outside the wall. You can use a separate single
gang plate and install the supplied jack on it and wire it to the
terminals on the back of the AC504A-WP or AC602.
You can use 20 awg or heavier wire to extend the DC output cord
of the power supply if you need to locate the power supply farther
from the device. It is recommended to keep the distance of the
supply from the unit to within 30 feet.
Note: Please do not connect the power supply to the AC source
until you have securely connected the output cords to the Wall
Plate Mini-Cat unit.
Electrical Safety Note
Since the DC supply to the unit is only 9 vDC with minimal current
requirements, the product qualifies as a Class 2 low-voltage device,
and you are not required to run the DC cables in a conduit.
However if you will be installing the power supply in the wall or ceiling,
since it has to plug in to AC, you need an electrical junction box for it,
and the AC line that brings high-voltage to the junction-box should
follow the electrical code for your specific installation
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Mini-Cat5 Extender Wallplate Transmitter
5. Apply a video source to the system and
check for an image at each receiver, then
set the compensation Potentiometer (pot)
for best possible image.
Note: If the source is Component Video
(YPbPr) an HD15 to 3 RCA cable will
be required for each HD15 connector.
If the source is composite video with stereo audio, a similar
cable will be needed. The RCA connectors are typically yellow
(instead of green) for video and red/white for audio. To transmit
CV and stereo audio, please read section 2.3 below.
2.2 Video Compensation Adjustment
If the length of Cat5 cable is long, you need to adjust the receiver
(AC602A) to compensate for the signal in order to perfect the image.
Apply a video source to the system and check for an image at each
receiver, then set the compensation Potentiometer (pot) for best
possible image.
Start with the compensation pot fully CCW (least compensation), then
slowly turn it clockwise and check for the bleeding of left to right
horizontal lines on the screen.
Note dark line bleeding as a dark
line to the right
Note dark line has a clean transition
Note dark line bleeding as a white line
to the right!
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Model AC504A-WP
2.3 Configuration for Composite Video and Stereo Audio
The AC504A-WP can be used to transmit Composite Video and Stereo
Audio instead of VGA or YPbPr to the receiver. However since the
Video signals are terminated differently than audio, you need to cut or
remove two jumpers on the rear of the unit.
For normal operation (VGA or YPbPr), J1 and J2 on the rear of the
unit, are installed. For transmitting composite video and audio, you
need to remove or cut these jumpers.
An HD15 to 3 RCA cable will be required. The composite video is sent
on the green (pin 2), and the light and left audio channels are sent on
the Red (pin 1), and Blue (pin 3). Note that some cables may have
Yellow (video), Red (right audio), and White (left audio) RCA
connectors instead of RGB connectors.
NOTES
If the length of Cat5 Cable is longer than 300 feet you
may need to attach a power supply to the receiver unit.
Generally if the remote display device is referenced to ground
(i.e. the VGA connector ground or case, is connected to power
line ground) you should not need an additional power supply to
the specified maximum length of 500 feet
Do not connect this unit to any LAN device such as
network cards or hubs as this may damage the AC155A and/or
the LAN device. Use EIA/TIA 568B standard straight-through
patch wiring. Do not use crossover cables.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Mini-Cat5 Extender Wallplate Transmitter
3. Troubleshooting
1. Fuzzy, blurry, or ghosting image at remote location
If you have a stable image but it looks blurry (object or character edges
are smearing), adjust the compensation on the receiver. If you still have
a fuzzy image, try reducing the refresh rate and/or the resolution setting
of the video. For Best results use either low-skew cable (such as
Belden Brilliance® VideoTwist), or Cat5 (instead of Cat6).
2. Shaking image or periodically blanking monitor
A strong electromagnetic noise field can cause instability in the signal.
Usual sources of this form of noise coupling are high current AC lines
or other high-density data and/or control cables that run adjacent to and
parallel with a substantial length of the CAT5 cable.
To eliminate this, separate the Cat 5 cable of Mini-CAT5 Extender
from the interfering source or use shielded CAT5 cables. Usually
separating the CAT5 cable from the interfering source by a few inches
is sufficient to eliminate this problem.
If the length of Cat5 run exceeds 300 feet you may need an additional
power supply at the receiver.
Contacting Black Box
If you determine that your extender is malfunctioning, do not attempt
to repair the unit. Contact Black Box at 724-746-5500. Before you do,
make a record of the problem. We will be able to provide more
efficient and accurate assistance if you have a complete description.
Shipping and Packaging
If you need to transport or ship your extender:
• Package it carefully. Use the original container if possible.
• Before you shipping the unit, contact us to get a Return
Authorization (RA) number.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Model AC504A-WP
4. Specifications
Video Types VGA through UXGA (RGBHV, or YPbPr), or CV and
line level stereo audio
Resolution
Bandwidth
Up to 1600 x 1200 at up to 85 Hz PC or 1080i HDTV
DC to 450 MHz
Max. Distance Up to 328 ft. (100 m) with Phantom Power, or 500 ft
(150 m) with additional power supply at receiver for
VGA or 1200 feet for CV and audio
Connectors
Interfaces
HD15 female for video in and out; Shielded RJ45
Standard Analog VGA; Proprietary CAT5
Compliance CE; FCC Part 15 Subpart B Class A, IC Class
Max. Altitude 10,000 ft. (3048 m)
Temperature Operating: 32 to 122°F (0 to 50°C);
Storage: –40 to +185°F (–40 to +85°C)
Humidity
Enclosure
MTBF
Up to 95% non-condensing
Aluminum and Steel
100,000 hours (calculated estimate)
Power
From utility-power (mains) outlet, through included
Universal power adapter. Input Voltage: 100~240
VAC Output Voltage: 9v DC regulated at 1.7A Max
(actual power consumption of the sender and the
receiver, is 200 ma nominal (1.8 watts)
Dimensions
Weight
2.75" W X 4.5" L X 1" D
0.5 lbs
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Mini-Cat5 Extender Wallplate Transmitter
5. Appendix
EIA/TIA 568B WIRING STANDARD
PIN
Wire Color
1
2
3
4
5
6
7
8
White w/ Orange Stripe
Orange
White w/Green Stripe
Blue
White w/Blue Stripe
Green
White w/Brown Stripe
Brown
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Model AC504A-WP
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
© Copyright 2007. Black Box Corporation. All rights reserved.
1000 Park Drive Lawrence, PA 15055-1018 724-746-5500 Fax 724-746-0746
Download from Www.Somanuals.com. All Manuals Search And Download.
|