TS580A-R4
CAT5/5e/6 LAN Performance Verifier
Digitally certify cables and devices
in Gigabit Etthernet networks.
Customer Order toll-free in the U.S.: Call 877-877-BBOX (outside
Support
Information
U.S. call 724-746-5500) FREE technical support 24
hours a day, 7 days a week: Call 724-746-5500 or fax
724-746-0746 Mailing address: Black Box Corporation,
1000 Park Drive, Lawrence, PA 15055-1018 Web site:
•
E-mail: [email protected]
ownload from Www.Somanuals.com. All Manuals Search And Downloa
NOM Statement
Normas Oficiales Mexicanas (NOM)
Electrical Safety Statement
INSTRUCCIONES DE SEGURIDAD
1. Todas las instrucciones de seguridad y operación deberán
ser leídas antes de que el aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser
guardadas para referencia futura.
3. Todas las advertencias en el aparato eléctrico y en sus
instrucciones de operación deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser
seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—
por ejemplo, cerca de la tina de baño, lavabo, sótano
mojado o cerca de una alberca, etc.
6. El aparato eléctrico debe ser usado únicamente con
carritos o pedestales que sean recomendados por el
fabricante.
7. El aparato eléctrico debe ser montado a la pared o al
techo sólo como sea recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al
equipo eléctrico más allá a lo descrito en las instrucciones
de operación. Todo otro servicio deberá ser referido a
personal de servicio calificado.
724-746-5500
|
blackbox.com
Page 3
ownload from Www.Somanuals.com. All Manuals Search And Downloa
NOM Statement
9. El aparato eléctrico debe ser situado de tal manera que su
posición no interfiera su uso. La colocación del aparato
eléctrico sobre una cama, sofá, alfombra o superficie
similar puede bloquea la ventilación, no se debe colocar
en libreros o gabinetes que impidan el flujo de aire por los
orificios de ventilación.
10. El equipo eléctrico deber ser situado fuera del alcance de
fuentes de calor como radiadores, registros de calor,
estufas u otros aparatos (incluyendo amplificadores) que
producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente
de poder sólo del tipo descrito en el instructivo de
operación, o como se indique en el aparato.
12. Precaución debe ser tomada de tal manera que la tierra
fisica y la polarización del equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal
manera que no sean pisados ni pellizcados por objetos
colocados sobre o contra ellos, poniendo particular
atención a los contactos y receptáculos donde salen del
aparato.
14. El equipo eléctrico debe ser limpiado únicamente de
acuerdo a las recomendaciones del fabricante.
15. En caso de existir, una antena externa deberá ser
localizada lejos de las lineas de energia.
16. El cable de corriente deberá ser desconectado del cuando
el equipo no sea usado por un largo periodo de tiempo.
17. Cuidado debe ser tomado de tal manera que objectos
liquidos no sean derramados sobre la cubierta u orificios
de ventilación.
Page 4
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
NOM Statement
18. Servicio por personal calificado deberá ser provisto
cuando:
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro
del aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra un
cambio en su desempeño; o
E: El aparato ha sido tirado o su cubierta ha sido dañada.
724-746-5500
|
blackbox.com
Page 5
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Trademarks Used in this Manual
Trademarks Used in this Manual
Black Box and the Double Diamond logo are registered
trademarks of BB Technologies, Inc.
Microsoft, Excel, Windows, and MS-DOS are registered
trademarks of Microsoft Corporation.
UNIX is a registered trademark of X/Open Company Ltd.
Any other trademarks mentioned in this manual are
acknowledged to be the property of the trademark owners.
Page 6
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Table of Contents
Table of Contents
1. Specifications .....................................................................8
2. Overview ..........................................................................9
2.1 Introduction...............................................................9
2.2 Features.....................................................................9
2.3 What’s Included ......................................................10
2.4 Applications.............................................................11
2.5 The LPV List of Functions...........................................13
3. The Three Phases of LAN Installation ..............................15
4. Faceplate Description.......................................................16
5. Documenting Test Results................................................18
6. Operation ........................................................................19
6.1 Powering On and Backlighting................................19
6.2 The Main Unit’s Navigation Button.........................20
6.3 Main Menu..............................................................20
6.3.1 CAT5/6 UTP Cable Testing............................21
6.3.2 CAT5/6 UTP LPV Level 1...............................22
6.3.3 CAT5/6 UTP LPV Level 2...............................29
6.3.4 Reviewing CAT5/6 UTP Test Results.............32
6.3.5 CAT5/6 Basic Test.........................................40
6.3.6 Coax Testing .................................................44
6.4 Naming/Saving Test Results....................................47
6.5 Reviewing/Erasing Printer Memory.........................51
6.6 Printing from a PC...................................................54
6.7 Network Testing......................................................60
6.7.1 Scan One Port................................................61
6.7.2 Monitor Inline................................................64
6.7.3 Send Beacon................................................. 67
Appendix A. Straight-through Cable Coupler.......................69
Appendix B. Ping and TCP/IP Debugging Tools....................70
Appendix C. Examples of UTP Cable Faults..........................75
Appendix D. Making a Correct UTP Cable ...........................79
724-746-5500
|
blackbox.com
Page 7
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 1: Specifications
1. Specifications
Power — (2) 9-V batteries (one for test unit and one for probe)
Size — Test unit: 6"H x 3.125"W x 1.5"D (15.2 x 7.9 x 3.8 cm);
Probe: 1.5"H x 1.5"W x 8"L (3.8 x 3.8 x 20.3 cm)
Weight — Kit: 2.05 lb. (0.93 kg);
Test Unit: 0.5 lb. (0.23 kg);
Probe: 0.25 lb. (0.11 kg)
Page 8
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 2: Overview
2. Overview
2.1 Introduction
Over half of all network problems are caused by faulty cables.
And with network speeds increasing exponentially, the need for
affordable, sophisticated test equipment is more apparent than
ever before.
With the CAT5/5e/6 LAN Performance Verifier, you can check
your network cabling and devices to ensure they work at the
speeds promised by their manufacturers. Ideal for IT managers
and technicians responsible for cabling and network hardware,
the CAT5/5e/6 LAN Performance Verifier enables you to quickly
spot slow cables, bad connectors, incorrect wiring, improper
lengths, and low signal levels from hubs, switches, PCs, and
other LAN hardware. It digitally certifies cables and devices in
Gigabit Ethernet networks.
You can also decode your network devices’ capabilities and
signal levels, and even place the tester in-line between any two
devices to determine the negotiated speed. Or perform single-
side tests without powering down devices or unplugging cables.
2.2 Features
• Verify that cables and LAN hardware perform at their
advertised speeds.
• High-speed TDR provides nanosecond-accurate results.
• Locates opens, shorts, and splits, and pinpoints the exact
distance to the fault or split.
• Stores up to 250 test results you can download to your PC via
the USB port.
• Includes a toner/probe to locate wires in crowded wiring
closets.
• Tests 10-, 100-, and 1000-Mbps devices for data signal levels.
724-746-5500
|
blackbox.com
Page 9
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 2: Overview
• Enables you to test in-line between two devices to determine
the autonegotiated speed.
• Sophisticated algorithm converts test results into easy-to-read
graphs that clearly show the cable’s speed capability
(CAT3/5/5e/6).
• Transfer the test results from up to 250 stored tests to your
PC’s Excel® spreadsheet via the USB port.
2.3 What’s Included
• (1) tester
• (1) tuner/probe
• (2) CAT5e cables
• (1) RJ-45 to coax adapter
• (1) USB cable
• (1) results tablet
• “Passed” stickers
• (2) 9-volt batteries
• (1) software CD
• (1) case
• This user’s manual
CAUTION: When connecting, the LAN Performance Verifier
has two RJ-45 jacks (“LEFT,” “RIGHT”). The LEFT
jack is for testing cables (the jack is not protected
from voltages).
The RIGHT jack is for testing switches (it is
protected from PoE voltage).
Protect the LPV from telephone and Power over
Ethernet (PoE) voltages by using the "RIGHT"
socket when connecting to these devices and
when toning.
Page 10
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 2: Overview
Help with device installation and PoE:
Installers of VoIP phones, IP cameras, or access
points should use a power panel for exact measure-
ments of PoE voltage and power usage, displaying
the presence of 10,100,1000 switches and the pair
location of each.
NOTE: Power over Ethernet (PoE) powers devices over the
CAT5/6 cable.
2.4 Applications
Works with UTP and all Ethernet devices: Unlike traditional
certifiers, the LAN Performance Verifier (LPV) uses digital circuit-
ry and digital testing techniques to perform its tasks. These tests
include traditional TIA568 cable verification (length, opens,
shorts, split pairs, wire map) for unshielded twisted pair (UTP)
plus the LPV's own sophisticated crosstalk, timing, and cable
parameter tests that yield a UTP cable's category (CAT3, CAT5,
CAT5e, CAT6) and speed capability (10, 100, 1000 Mbps). And
the LPV can use your own network devices (hubs, switches, PCs)
to test UTP cables with real data. The LAN Performance Verifier
analyzes links and data from all types of hubs, switches, and
PCs. It performs both single-sided tests for advertised speed (10,
100, 1000 Mbps, and duplex) and inline tests (between devices)
for negotiated speed. The engine of the LPV circuitry is capable
of 1 nanosecond resolution.
Works with coax cable: Use the LPV to test for the length of
the cable, opens, shorts, wiremap, and distance to any faults
that might exist. As with UTP, coax can be toned with the toner
feature and test results can be stored in the LPV’s flash memory
for printing later. No LPV tests are performed on coax cable.
724-746-5500
|
blackbox.com
Page 11
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 2: Overview
What is LAN Performance Verification?
LAN performance verification means that a UTP cable passed a
prescribed battery of tests and is therefore not likely to cause
problems later. The LPV has two levels of verification:
LPV Level 1: Performed with the Main Unit and the Remote
Probe, Level 1 tests the cable for length; opens, shorts, split pairs
and distance to the fault; wire map (displays cable wiring); NEXT
and FEXT (crosstalk tests); propagation delay (time to transit
cable); skew (time delay between pairs); cable category (CAT3,
5, 5e, 6); and speed projection (10, 100, 1000 Mbps).
LPV Level 2: Includes all Level 1 tests plus it takes advantage of
a real live data source (hub, switch, or PC) to test for attenuation
and device type. An LPV Level 2 test verifies speed of both the
cable and the LAN device.
Networks are installed in steps. First, cables are installed. Then
hubs, switches, and PCs follow. Cables and network interfaces
are known as the physical layer. The higher software layers
provide addressing, file transfers. etc. If the physical layer does
not work, the communications layers (software) will not work.
Debugging cables, ports, and network software together is
time-consuming, frustrating, and ultimately very expensive.
There are too many unknowns. Using a LAN Performance
Verifier on your cables eliminates unknowns, making it easier to
get a network up and running. And, once the hardware is
operational, you can run software layer tests (ping, etc.) from
any workstation (see Appendix B).
What is the best time to LAN Performance Vertify a cable?
The best time to vertify a cable is when the installer is still readily
available to repair any faults that are found. Installers should
verify before they leave, so that they will not lose money by
having to return to a job site to do warranty repairs. Network
professionals should also verify before the warranty period
expires.
Page 12
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 2: Overview
2.5 The LPV List of Functions
UTP CABLES. LAN Performance Verification Level 1 tests:
√ Length measurement of each cable pair.
√ Locates opens, shorts, and distance to the fault.
√ Locates split pairs and the distance to the split.
√ Wire map. Graphs cables’ internal pairing.
√ NEXT (near-end) and FEXT (far-end) crosstalk.
√ Propagation delay (time for data to travel the length of the
cable).
√ Skew (time delay between pairs).
√ Cable typing. CAT 3, 5, 5e, 6.
√ Speed Projection: Displays test results as a graph projecting
the cable’s speed capability (up to 1 Gbps).
UTP CABLES. LAN Performance Verification Level 2 tests. Adds:
√ Attenuation. Graphs level of real live data from PC, hub or
switch.
√ Speed Vertification (Level 2). Enhanced speed display samples
real live data on active pairs to the limit of the device (1 Gbps).
NOTE: Level 2 tests use real data from your hub, switch, or PC.
COAX CABLES:
√ Length, open, shorts, distance to fault, tone, and wire map.
NETWORK DEVICE TESTING:
√ Single-sided and inline port tests check the ability of the hub,
switch, or PC to communicate by displaying their advertised
and negotiated capabilities.
724-746-5500
|
blackbox.com
Page 13
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 2: Overview
√ Data signal strength. Single-sided test exercises the suspect
hub, switch, or PC and displays the data signal strength of
active pairs.
NAMING TEST RESULTS, PRINTER, AND TONER PROBE:
√ Naming tests. Test names can be up to 16 characters each.
√ Toner/probe. Includes a full-featured toner/probe. Tones coax
and all 4 UTP pairs to locate wires in crowded wiring closets.
√ Printer memory. Stores test results for up to 250 UTP and coax
tests for later printing (requires a PC with Excel). USB data-
transfer cable and software is included.
Page 14
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 3: The 3 Phases of LAN Installation
3. The Three Phases of LAN Installation
The LPV is designed for the network installer, the network repair
person, and the IT manager. The tests used during the three
phases of LAN installation can also be used to troubleshoot
LANs that have operational problems.
The installation of a LAN is generally handled in phases. The
cabling is installed; then the switches and PCs are installed; and
then everything is connected. The LPV plays a role during all
three phases, saving countless hours of troubleshooting.
Phase I. Use the LPV during cable installation (before the
switches and PCs are installed). After the LAN cable has been
pulled through the building and terminated, it is good practice
to verify LAN performance. Verify that the cabling is terminated
properly and test that the cable is proper for the intended use
(for example, CAT5e for Gigabit networks).
Phase II. Use the LPV after the switches and PCs are installed.
Before connecting the cables to the switches and PCs, verify that
each switch port and PC are operational. This provides a wealth
of information:
It verifies that the device is ON (that is, it is transmitting); the
speed of the device (10, 100, 1000 Mbps) ; duplex; and other
features.
Phase III. Use the LPV when connecting the cabling to the
switches and PCs. With the cabling verified and LAN
Performance Verified (Phase I) and the switch and PCs checked
out (Phase II), all that remains is 1) getting the equipment com-
municating and 2) verifying each LAN link is performing at the
speed expected. To do this, use LAN Performance Verification
Level 2 to test the cable and port combinations. And use the
network tests inline capability to connect the LPV between 2
LAN devices to verify the negotiated speed of the link.
724-746-5500
|
blackbox.com
Page 15
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 4: Faceplate Description
4. Faceplate Description
The CAT5/5e/6 LAN Performance Verifier is illustrated in Figure
4-1. Its components are described here.
Components
1. LPV Main Unit
The Main Unit connects to any CAT 5/6, coax cable or 10, 100,
or 1000BASE-T device and performs tests needed for their instal-
lation and repair. For certain tests, it can be inserted inline
between two LAN devices.
2. Main Unit Jacks
Left, Coax, and Right: Use the left jack for UTP testing. Use the
right jack for network testing.
3. “Printer” port
Use to transfer stored testing data (up to 250 tests) to a PC. This
requires Excel. USB data-transfer cable is included.
4. Power and LCD backlighting
Press the recessed power button. To backlight the display, press
the SEL button during the opening screen. The LPV powers OFF
if there is no activity for 10 minutes.
5. Cursor and SELECT buttons
Use the cursor buttons to select the function to be performed.
Press the SEL button to select the functions.
6 and 7. LPV Remote Probe
The Remote Probe performs 2 functions:
6. Tracing cables: Use it as an inductive probe to trace cables
with the tone generated by the Main Unit.
7. Far-end cable termination: The Remote Probe's jack is used to
terminate the far end of the cable when the wire map test is
conducted.
Page 16
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 4: Faceplate Description
Figure 4-1. LAN Performance Verifier and Remote Probe.
724-746-5500
|
blackbox.com
Page 17
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 5: Documenting Test Results
5. Documenting Test Results
The LAN Performance Verifier includes three ways to document
your test results.
1. You can use a custom tablet (included) to fill in the test
results.
2. You can apply “PASSED” stickers (included) to wall outlets
and LAN devices to verify their capability.
3. You can print the results. Printer Memory stores test results
for up to 250 LAN performance verification tests, basic UTP
tests, and coax tests for later printing (requires a PC with
Excel). A 6-ft. (1.8-m) USB transfer cable, driver, and software
is included.
“Passed” stickers
Documentation tablet
Transfer readings
to Excel for printing
(USB cable included).
See Section 6.5.
Figure 5-1. Test results.
Page 18
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
6. Operation
6.1 Powering On and Backlighting
Figure 6-1 shows the tester’s backlight selection screen. Figure
6-2 illustrates the tester’s power button.
Figure 6-1. Backlight selection screen (lighting the LCD display).
Figure 6-2. Power/selection button.
POWERING ON: Press the power button (PWR) and release to
turn ON the tester. The “backlighting” screen appears (see
Figure 6-1). Pressing the select (SEL) button while this screen is
present turns on LCD lighting (“backlighting”). Backlighting is
important when working in dim light, but it shortens battery life.
NOTE: Once enabled, the LCD will remain backlit until the tester
is powered OFF. The backlight selection screen (Figure
6-1) is always lighted during the 3-second period that it is
displayed. This allows you to turn the tester ON in a dark
area and SELECT backlighting during the process.
724-746-5500
|
blackbox.com
Page 19
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
6.2 The Main Unit’s Navigation Button
To navigate through the LAN Performance Verifier screen, use
these keys:
Figure 6-3. Navigation buttons.
• PWR. Power ON/OFF (see previous page for backlighting).
• SEL (SELECT). Press to perform task. Appears as uon LCD.
• The UP arrow. Appears as pon LCD.
• The DOWN arrow. Appears as qon LCD.
The SELECT button’s function always selects the task. But the
function of the UP and DOWN arrow buttons may change with
each screen. For example, the Main Menu uses the UP arrow
button to return the tester to the MAIN MENU and uses the
DOWN arrow button to scroll the cursor.
6.3 Main Menu
Figure 6-4. Main menu.
Page 20
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
This menu shown in Figure 6-4 is the gateway to all the LPV’s
tests. Scroll the cursor with the down arrow button and press
SELECT to perform the task.
uCAT5/6 UTP: Test and verify UTP cables with or without LAN
devices (hubs, switches, PCs) connected. Perform basic cable
tests on UTP cables. Tone UTP cables. Move the cursor to
CAT5/6 UTP and press Select.
uCOAX CABLE: Test coax cables for length, opens, shorts,
distance to fault, and wire map. Two adapters are included. Tone
coax cables. See Section 6.3.6.
uNETWORK PORTS: Perform tests on LAN (hubs, switches, PCs)
devices. Move the cursor to Network Ports and press Select.
uPRINTER MEMORY: Printer memory is used to store the results
of up to 250 LPV Level 1, Level 2, basic tests, and coax tests for
later printing. Move the cursor to Printer Memory and press
Select if you want to Review the tests stored in memory or Erase
memory.
6.3.1 CAT5/6 UTP Cable Testing
Figure 6-5. UTP cable testing menu.
VERIFY UTP: Move the cursor to VERIFY UTP and press Select to
start LPV Level 1 testing of a cable. LPV tests have two levels:
Level 1 uses the Main Unit and Remote Probe to perform the
basic cable testing plus speed parameter testing and cable
category testing.
724-746-5500
|
blackbox.com
Page 21
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
When the Level 1 test is complete, you can choose to
continue to Level 2 and use real data from your own hub,
switch, or PC to expand the testing. Verify is designed for 4-pair
cable only (use Basic Test UTP for other pairings). See Section
2.5, List of Functions for a listing of tests. 250 test results can be
stored for later printing.
BASIC TEST UTP: Move the cursor to Basic Test UTP and press
Select to test UTP cable for length, opens, shorts, split pairs (plus
distance to these faults), and wire map. BASIC TEST UTP does
not perform LAN performance verification.
TRACER TONES ON: Move the cursor to Tracer Tones On and
press Select if you wish to energize a cable with a tone (plug the
cable into the Main Unit's RIGHT jack). The Remote Probe
detects the tone at the far end of the cable. This is useful in
locating cables in crowded wiring closets. When selected, tracer
tones will stay on for one hour.
NOTE: Use the right jack when tracing unknown cables (it is
protected from accidental high voltage exposure).
6.3.2 CAT5/6 UTP LPV Level 1
Figure 6-6. Verify UTP.
Perform LP Verification Level 1 (UTP cables) and Level 2 (UTP
cables and LAN devices).
Page 22
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
Figure 6-7. Press the down arrow button q
after cable is connected.
Follow the instructions. Only an uncoiled cable will give you
accurate test results. At this point in the testing, the far end of
the cable should not be connected to any device.
NOTE: If the cable is connected to a device, you will be alerted to
check the far end of the cable. When ready to proceed, press
the down arrow (qTEST).
Error Messages: If there is a problem that stops the test from
proceeding, one of the following error messages will be
displayed:
CABLE IS ACTIVE: There is an active network port on the far end
of the cable. You will need to unplug it to proceed.
CHECK CABLE END: A voltage is present on one or more of the
cable pairs, or the Remote Probe is connected to the cable end
when it is not needed. You will need to unplug it to proceed.
NO CABLE: There is no cable connected or an inactive port is
plugged into the far end of the cable.
NOTE: If errors persist from test to test, contact Black Box
Technical Support at 724-746-5500
724-746-5500
|
blackbox.com
Page 23
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
Figure 6-8. Stranded or Solid wire selection screen.
The LAN Performance Verifier has the unique ability to test both
cables constructed of stranded wire (commonly called “patch”
cables) and solid-core wire. Scroll to select the cable and press
Select.
How to tell the difference: If the cable is installed in a wall, it is
almost certainly a solid core wire. Preassembled cable with end
fittings already attached is usually stranded cable. Also, stranded
cable is more flexible than solid wire. If you bend the cable and it
does not attempt to spring back to its original shape, it is most
likely solid cable.
NOTE: The minimum length of each cable type is shown on the
screen for Verify Tests. If your cable is shorter than this,
use the Basic Cable Test. Once the selection is made,
cable testing will automatically commence.
Page 24
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
Figure 6-9. Testing progress is shown on the screen.
Figure 6-10. Any problems will be displayed (see Appendix C).
During this phase of testing, information about length, opens,
shorts, split pairs, crosstalk, cable category, and speed is being
gathered and computed. If there are no cable problems, testing
continues until you are prompted to connect the Remote Probe
and perform a wire map test. If all is OK, testing will finish (the
“speed” screen is displayed).
NOTE: If there is a problem with the cable, the problem will be
displayed, and testing will be halted. The problem must
be corrected before testing can continue. See Appendix C
for examples of cable failures.
Complete results are immediately available for Review and
Saving after the test is completed. This “test now, review later”
feature greatly speeds up the test process when you have
multiple cable installations.
724-746-5500
|
blackbox.com
Page 25
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
Time to test: Short cables take longer to test because fewer
measurements per pass are possible. The thousands of
measurements required are accomplished much faster on longer
cables than shorter cables.
Figure 6-11. Testing is halted
until the Remote Probe is connected.
The Remote Probe is required for the wire map to be
constructed. Plug the Remote Probe into the far end of the
cable. Tracer tones have been turned ON to help locate cables in
crowded areas (press the TRACE button on the Remote Probe
and hold it close to the cable to follow the tone). The Main
Unit’s wire map test is triggered when the Remote Probe is
connected to the far end of the cable (there are no buttons to
push). The wire map tests for correct cable pairing.
NOTE: The wire map is displayed during the Review process, not
during the test.
Remote Probe LEDs. The Remote Probe needs to be connected
only for a brief period. Flashing LED(s) indicate the test is pro-
gressing. A steady LED indicates the test is completed. This saves
you an extra trip to retrieve the probe. If LED(s) continue to flash
the cable, the cable has a wiring problem. Disconnect the probe
and go to the Main Unit to see the results.
NOTE: If you plan to test to LAN Performance Verification Level
2, now is a good time to plug in the hub, switch, or PC (it
will save you a trip).
Page 26
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
Figure 6-12. Remote probe.
Figure 6-13. LPV Level 1 final screen (when you see this,
Level 1 is completed and available for review).
When the above screen appears, the Level 1 LPV is complete. If
you select REVIEW/SAVE, you will enter the Test Results Option
Screen. To discard the test results immediately, select EXIT.
724-746-5500
|
blackbox.com
Page 27
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
Figure 6-14. Test results option screen.
REVIEW TEST: View results from the Level 1 test. After the
review, you may return to this screen to NAME/SAVE the results.
SAVE READINGS: Store the test results in PRINTER MEMORY for
printing later and do not continue to Level 2 testing. The next
sequential Reading Number (1–250) will be assigned along with
any name that has been created (see EDIT TEST NAME below).
LPV TEST PORT: Continue to Level 2 verification. Requires a PC,
hub, or switch to drive the cable.
EDIT TEST NAME: Create a name (not required) that is stored
with the sequential reading number. If you continue to Level 2
you will have another chance to create a name.
EXIT: Discards the test results and returns to the Main Menu.
Page 28
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
6.3.3 CAT5/6 UTP LPV Level 2
Figure 6-15. Perform LAN Performance Verification Level 2.
(UTP cables and LAN devices).
Figure 6-16. If you have selected to continue with LAN
Performance Verification Level 2, this screen appears.
LAN Performance Verification Level 2 adds to the battery of tests
conducted in Level 1 by testing the cable with real live data from
any hub, switch, or PC.
NOTE: The screen (above) reminds you that the best source of
data is a Gigabit device. A Gigabit device drives the cable
with data up to a Gigabit speeds (1000 Mbps) on all four
pairs. Connect the port to the cable and press qto
continue with Level 2.
724-746-5500
|
blackbox.com
Page 29
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
FAQ: What is the difference between Level 1 and Level 2
and when do I use it? Level 1 verification tests for length,
opens, shorts, split pairs (including distance to the fault) along
with propagation delay, skew, NEXT, FEXT, and cable category
measurements. Level 1 testing uses simulated digital signals to
test the cable. Level 2 adds to the testing with the use of real live
data from a NIC, hub, or switch. Use Level 1 for new cable
installations or anytime a LAN device (hub, switch, PC) is not
available.
Figure 6-17. Testing Link Pulses from a Gigabit device.
Figure 6-18. Testing Link Pulses from a 100-Mbps device.
The first step in the Level 2 process is to read the link pulses of
the LAN device and determine its advertised capability. Every
LAN device broadcasts its capability in terms of speed, duplex,
and other features (known as “advertised” capabilities) to other
LAN devices.
Page 30
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
First example (shown in Figure 6-17): The LPV has found a
Gigabit device (1000 Mbps) on Pairs 1, 2 and 3, 6 that is capable
of transmitting at 10, 100, and 1000 Mbps at full-duplex.
1000-Mbps devices use all 4 pairs.
Second example (shown in Figure 6-18): The LPV has found a
100-Mbps device on Pairs 3, 6 that is capable of transmitting at
10 and 100 Mbps at half-duplex. Typically, devices that transmit
on Pairs 1, 2 are PCs and devices that transmit on 3, 6 are hubs
and switches.
When completed, press the down arrow key qto continue.
Data Signal Levels: Immediately following the link pulse test,
the Main Unit tests the data signal levels from the LAN device.
The levels are not displayed at this time but are available during
Review.
Figure 6-19. LPV Level 2 final screen (when you see this screen,
Level 2 is completed and available for review).
When the above screen appears, the Level 2 LPV is complete.
The complete results of both the Level 1 and Level 2 readings
are available for immediate review. You have the choice of
discarding the test readings (“EXIT”) or REVIEWING or SAVING
the Level 1 and Level 2 readings in Printer Memory (“REVUE/
SAVE”).
NOTE: If you select Revue/Save, you will have an option to name
the test (Edit Test Name) before saving.
724-746-5500
|
blackbox.com
Page 31
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
Figure 6-20. Review, create a name for the test
and/or save the test results.
6.3.4 Reviewing CAT5/6 UTP Test Results
Figure 6-21. Review the readings from the most recent test or
store the readings in printer memory.
Page 32
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
Figure 6-22. Cable Category is the first screen
of many that are stored.
The “cable category” is universally accepted as the speed
capability of the cable. CAT3 was the original twisted-pair cable
that connected 10-Mbps networks together. Then came CAT5
(used in networks up to 100 Mbps). Followed by CAT5e (gener-
ally considered adequate for up to 1000-Mbps networks). As
you become familiar with cable category, you will notice that
few cables get rated higher than their factory labeling. This is
because cables are manufactured and tested to minimum
specifications. If the cable exceeds minimum specifications, it
passes the manufacturer's inspection.
When ready to proceed, press qREVIEW.
Figure 6-23. Verification Level 1 Speed Projection.
724-746-5500
|
blackbox.com
Page 33
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
LAN Performance Verification Level 1 displays the projected
speed capability of the cable. The graph is a result of thousands
of measurements used to project the speed of the cable. This is
one of the most useful and money-saving displays. For instance,
it is possible that some shorter, installed CAT5 cable (rated for
100 Mbps) are capable of communicating at a 1000 Mbps. This
graph will indicate such. Many users conclude their cable testing
with Level 1 and skip the Level 2.
Figure 6-24. Length/Timing summary screen.
Length: The length of the shortest cable pair (in feet). 330 feet
(100 m) is the longest cable allowed by the 802.3 standard.
The LAN Performance Verifier can test cables up to 1250 feet
(381 m) in length.
Propagation delay: The time it takes for a data signal to travel
the length of the cable (in nanoseconds). An abnormally long
propagation delay indicates the cable is “too slow” for the
application. Either the cable itself is too slow or there is an error
in the wiring. The standard allows a maximum 555 nsecs
propagation delay (CAT6 cables).
Skew: The difference in the propagation delay between the
slowest pair and the fastest pair in the cable (in nanoseconds). A
small skew ensures that data, on each pair, will arrive at the
receiver at about the same time. A large skew reading causes
errors. 50 nsecs is the maximum allowable skew.
To continue reviewing, press the down arrow key q.
Page 34
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
Figure 6-25. LPV Level 1 Pass/Fail Summary Screen.
DELAY OK: The propagation delay of the cable is within specifi-
cation.
SKEW OK: The skew of the cable is within specification.
NEXT OK, FEXT OK: Indicates that “near end crosstalk” (at the
near connector) and at “crosstalk far end” (a distance removed
from the near connector) is within acceptable limits. Crosstalk is
interference created by signal coupling between adjacent wires
of the cable.
SPLIT OK: The wire contains no split pairs. See Appendix D for a
definition of "split pairs" and notes on making a correct cable.
MAP OK: The pair wiring of the cable is correct. See Appendix
D.
PATCH/SOLID: The type of wire specified.
TOL(TOLERANCE): A calculated value using cable length, delay,
NEXT, FEXT, cable category (CAT 3, 5, 5e, 6) and speed (10
Mbps, 100 Mbps, 1000 Mbps). Zero percent equals failure to
meet specifications at a given speed. One percent is barely
passing; 100 percent is maximum tolerance.
Tolerance is largely cable length driven. The longer the cable is,
the less the tolerance. However, lower category cables eat up
tolerance faster than higher category cables.
724-746-5500
|
blackbox.com
Page 35
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
If tolerance is below 15%, you may wish to consider using a
repeater, hub, or switch to shorten the cable run. This is
especially true if you are in a “noisy” environment (large electro-
mechanical machines, etc.).
Figure 6-26. A correct wire map for a straight through cable.
WIRE MAP: The wire map displays the pairing of the wires in the
cable. The example wire map indicates that the first pair
(comprised of Pins 1 and 2) is 203 feet long and terminates in
Pins 1 and 2 on the far end of the cable.
Figure 6-27. Propagation and skew (per pair) screen.
Page 36
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
Figure 6-28. Propagation and skew per pair.
Timing data per pair: The next two screens give you the timing
of the propagation delay and skew for each pair in the cable.
Large variations between pairs indicate trouble.
NOTE: A given pair’s skew is the difference in propagation delay
between that pair and the slowest pair in the cable.
The following screen only appears if Verification Level 2 was
performed:
Figure 6-29. Signal levels of real live data from a Gigabit switch.
724-746-5500
|
blackbox.com
Page 37
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
Figure 6-30. Signal levels of real live data
from a 100-Mbps switch.
The signal level screen is one the most powerful tools used
during Level 2 verification. It is a live signal attenuation display.
If the level is below the DATA MIN line, you may experience
faulty transmissions. If the signal is well above the DATA MIN
line, you have plenty of "headroom". Press the down arrow key
qto continue.
The two examples above show the differences between Gigabit
devices and 10-and 100-Mbps devices. With a Gigabit device it
is possible to view real live data on all four pairs whereas a
10- and 100-Mbps device can only transmit on one pair. A
Gigabit device is a full duplex device that uses all four pairs,
therefore making it a perfect device to get a full view of all four
pairs of the cable.
The following screen only appears if Verification Level 2 was
performed:
Figure 6-31. LAN Performance Verification Level 2
summary screen.
Page 38
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
LAN Performance Verification Level 2 displays the LAN
Performance Verified Level 2 speed capability of the cable. The
display is the result of the data gathered during Level 1 testing
(simulated data) and Level 2 testing (real data) into a graph that
“LAN Performance Verifies” the speed capability of the cable.
Additional notes: The Level 2 testing adds real live data with the
connection of a real live data source (a hub, switch, or PC) to the
far end of the cable. This adds an important test element: signal
attenuation of live data. Adding this to the test data gathered
during Level 1 testing creates Level 2 testing. The end result of
LAN Performance Verification Level 2 is the speed graph shown
above. It verifies the measured data speed capability of the cable
in Figure 6-31. Use Level 2 verification whenever you want to
test a cable with real live data. With the Level 2 testing, you are
LAN Performance Verifying both your cable and your network
port at the same time (you can test your cable with the exact
port that it will use in the network).
Figure 6-32. If you see this screen again, you are
reviewing the same data again.
Select EXIT at any time to stop the Review. If you select EXIT,
you will be given the option to SAVE the test results with
or without a NAME or to discard the results. Select REVIEW
to continue reviewing.
724-746-5500
|
blackbox.com
Page 39
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
Figure 6-33. Test results option screen “EXIT.“
See Section 6.4 for Saving and Naming instructions.
NOTE: Once a reading is SAVED, it is too late to create a NAME.
6.3.5 CAT5/6 Basic Test
Test UTP for opens, short, split pairs, length and distance to
fault.
Figure 6-34. Basic UTP testing.
Page 40
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
Figure 6-35. UTP Cable Test Main menu.
BASIC TEST UTP: Move the cursor to BASIC TEST and press
SELECT to test a UTP cable for length, opens, shorts, split pairs
(plus distance to these faults) and wire map. BASIC TEST UTP is a
quick test and does not perform LAN Performance Verification.
Basic test results can be stored in Printer Memory.
NOTE: BASIC TEST UTP is often used when a cable fails to pass
the LPV test. Or it is used to test 2-pair UTP wiring (LPV
can only be performed on 4-pair wire).
Figure 6-36. Press the down arrow button
after the UTP cable is connected.
Follow the instructions on the screen (plug the cable you wish to
test into the LEFT jack). Only an uncoiled cable will give you the
most accurate length measurement. At this point in the testing,
the far end of the cable should not be connected to any device.
724-746-5500
|
blackbox.com
Page 41
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
NOTE: If the far end of the cable is connected to any device it
will notify you to check the far end of the cable. When
ready to proceed, press (qTEST).
Error Messages: If there is a problem that stops the test
from proceeding, one of the following error messages will be
displayed:
CABLE IS ACTIVE: There is an active network port on the far end
of the cable. You will need to unplug it to proceed.
CHECK CABLE END: A voltage is present on one or more of the
cable pairs or the REMOTE PROBE is connected to the cable end
when it is not needed. You will need to unplug it to proceed.
NO CABLE: There is no cable connected or an inactive port is
plugged into the far end of the cable. Plug in the cable or
disconnect the inactive port.
Figure 6-37. Testing progress is displayed.
Cable testing has commenced. You can follow its progress
on the display. During this phase of testing, information about
length, opens, shorts, and split pairs is being gathered and
computed. If any cabling errors are encountered, you will be
alerted including the distance to any problems.
Page 42
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
Figure 6-38. UTP pairs and length are displayed.
Select MAP + TRACE for wiremap and tones.
Remote Probe LEDs. The Remote Probe needs to be connected
only for a brief period. Flashing LED(s) indicate the test is pro-
gressing. A steady LED indicates the test is completed. This saves
you an extra trip to retrieve the probe. If LED(s) continue to flash
the cable, the cable has a wiring problem. Disconnect the probe
and go to the Main Unit to see the results.
Figure 6-39. LEDs on the remote probe.
724-746-5500
|
blackbox.com
Page 43
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
Figure 6-40. A correct wire map
for a straight through UTP cable.
UTP WIRE MAP: The wire map displays the pairing of the wires.
The map above indicates that the first pair ("12>"), Pins 1 and 2,
is 203 feet long and terminates in Pins 1 and 2 ("<12") on the far
end of the cable. If there were any problems, they would be dis-
played.
Press SAVE to either SAVE or NAME and SAVE the test. Press
EXIT to discard the results.
6.3.6 Coax Testing
Figure 6-41. Test coax cable for opens, shorts,
length, and distance to fault.
Page 44
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
Figure 6-42. Select COAX CABLE from Main Menu.
COAX CABLE TESTING: Move the cursor to coax cable and press
SELECT to test a coax cable for length, opens, shorts (plus dis-
tance to these faults). Wire map and toning is also available from
this menu.
Coax cable test is a quick test and does not perform LAN
Performance Verification. Test results can be stored in Printer
Memory.
RJ-45/COAX ADAPTER: The Main Unit has a permanent COAX
connector labeled “Coax.” The RJ-45/Coax adapter is used to
connect the coax cable to the Remote Probe. Pins 1 and 2 of the
Remote Probe’s socket are used to test the coax cable.
Figure 6-43. RJ-45/coax adapter.
724-746-5500
|
blackbox.com
Page 45
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
Figure 6-44. Connect the coax cable to the F connector on the
Main Unit and select coax. The test begins.
At the beginning of the test, the far end of the cable should not
be connected to anything.
Figure 6-45. The coax pair (Pins 1 and 2) and length are
displayed. Select MAP + TRACE for wire map and tones.
Figure 6-46. A wire map for a coax cable.
Page 46
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
If the COAX CABLE TEST concludes with a wire map display and
no reported errors, the cable is error free.
Press SAVE to either SAVE or NAME and SAVE the test. See
Section 6.4 for instructions. Press EXIT to discard the results.
6.4 Naming/Saving Test Results
Figure 6-47. Naming and saving test results start at this screen.
All LPV tests, whether LPV UTP, Basic UTP or coax, eventually
arrive at this screen. It is here where you decide to SAVE the test
in PRINTER MEMORY (with or without a custom NAME).
REVIEW TEST: Review test results before they are SAVED. After
reviewing the test results, you can return to this screen.
SAVE READINGS: Store the results from the latest test in
PRINTER MEMORY for later printing. The next sequential
Reading Number (1–250) is automatically assigned along with
any NAME that you created (see EDIT TEST NAME below).
Creating a name is not required.
NOTE: The test results of all LPV cable tests can be NAMED and
STORED with the exception of LPV tests that did not
“PASS.”
LPV TEST PORT: For LPV UTP tests only.
EDIT TEST NAME: Create a name (not required) that is stored
with the sequential reading number. If you are going to create a
name, it must be created before the test is SAVED. See the
following page for instructions on creating a NAME.
724-746-5500
|
blackbox.com
Page 47
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
EXIT: Discards the test results and returns to the Main Menu.
Figure 6-48. Select EDIT TEST NAME to create a custom name
for the test results. Do this before saving the test in memory.
To NAME a reading, you must first complete any of the LPV’s
cable tests. At the end of the test, press the DOWN arrow
(labeled “REVIEW/SAVE” or “SAVE”) and the above screen
appears. Select EDIT TEST NAME.
NOTE: Creating a name (EDIT TEST NAME) for a test result
is optional. The LPV automatically assigns a sequential
number from 1 to 250 when SAVE READING is selected.
If a name has been created using EDIT TEST name, this
name will also be stored with the sequential number
when SAVE READING is selected.
Figure 6-49. Select START FRESH to create a name from scratch.
Select EDIT OLD to create a new name by modifying the prior
name. It saves time.
Page 48
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
For the purposes of learning the naming routine, select START
FRESH and follow the exercises in the next section (Naming Your
Tests). Once you become proficient with START FRESH, give the
EDIT OLD routine a try. It speeds creating names by allowing you
to copy an “old” reading name as the starting point for creating
the next cable reading name. See the next section, “Naming
Your Tests” for more details.
Naming Your Tests
Test name line (A
maximum 16-character
name appears here.)
Rotating “letter loop”
Figure 6-50. Naming test results screen.
Rotate loop with arrow keys until the desired letter, number,
space, backspace or MENU command appears on the left edge
of the LCD. Press SEL to copy character to the TEST NAME line.
After SEL is pressed, the letter loop conveniently positions to a
space character awaiting the next entry.
Figure 6-51. Buttons on the tester.
724-746-5500
|
blackbox.com
Page 49
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
The UP and DOWN arrows rotate the “LETTERLOOP” to the
right and left. The SEL key copies the letter to the TEST NAME
LINE. Create a label: Rotate the letter loop until the letter or
command desired appears at the leftmost of the display and
press the SEL button.
Exercise the “Rotating Letter Loop”
It‘s the best way to learn how to create a name.
Exercise #1. Moving the LETTER LOOP.
1. Press the DOWN arrow for 5 seconds: The LETTER LOOP
continually rotates to the left.
2. Press the UP arrow for 5 seconds: The LETTER LOOP
continually rotates to the right.
3. Press the SEL key: The leftmost character of the LETTER LOOP
is always copied up to the TEST NAME line. If it is a space, a
space is copied. If it is a u, the cursor moves to the right.
4. To exit back to the menu, use the arrow keys to position
“MENU” as the left-most character on the LCD and press SEL.
Exercise #2. Create the test name “TEST,” then erase:
Step 1: Position the LETTER LOOP so “T” is the left-most letter
on the screen (use the UP and DOWN arrow keys to position the
letter “T” at the left side of the LCD display).
Step 2. Press the SEL key, copying the “T” up to the TEST NAME
line. Now do the same for “E,” “S,” and “T.”
Step 3. If you make a mistake, try the letter loop’s “cursor
characters” (t u). They allow you to control the cursor’s
position. To erase a character, write over the character with a
“space” (blank) character. There are three of these in the letter
loop. For instance, a space character is located between the “.”
character and the letter A.
Page 50
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
Special characters in the LETTER LOOP:
tBackspace over letters without erasing them.
uForward space over letters without erasing them.
Space (blank). Use to erase letters or add spaces.
MENU: Use to exit the EDIT TEST NAME routine and return to
the MENU. If you select MENU, you have lost nothing. You can
still SAVE the reading in memory or re-enter the EDIT TEST
NAME routine.
“EDIT OLD” NAME Once familiar with the EDIT TEST NAME
routine, try using EDIT OLD NAME. The EDIT OLD NAME routine
requires a prior cable name to edit. Perform a cable test and
when naming, select EDIT OLD NAME. It speeds creating names
by allowing you to copy an “old” reading name as the starting
point for creating the next cable reading name. Use the back-
space, forward space, space character, and other characters to
modify the name. SAVE it when complete.
NOTE: The LPV allows duplicate names but when they are
printed in Excel, they will appear as “Jack A,” etc.
6.5 Reviewing/Erasing Printer Memory
Figure 6-52. Review or erase stored readings
(memory stores up to 250 readings).
724-746-5500
|
blackbox.com
Page 51
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
Figure 6-53. To review or erase stored readings, select PRINTER
MEMORY from the Main Menu.
PRINTER MEMORY: “Printer memory” is the storage location for
all saved test readings. It can store the results of up to 250 LPV
tests (Level 1 and/or combined Level 1 and Level 2), Basic UTP
tests, and coax tests for later printing. After each test is
conducted, you have the option to review, save, and/or name
the test results (readings) in printer memory for later printing.
This following screen is used if you wish to review the readings
after they have been stored. It is also used to erase all of the
stored readings.
You can connect the LAN Performance Verifier to a PC for data
transfer and printing.
Figure 6-54. Review or erase selection screen.
Page 52
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
REVIEW: Use the UP and DOWN arrow to find the reading you
wish to review in Printer Memory. Press SEL to review. “BLANK
TEST NAME” indicates a name has not been created for the test.
Figure 6-55. Review screen.
ERASE: Selecting the erase function erases all of Printer Memory.
There is no way to selectively erase readings. This screen verifies
that you wish to erase all of Printer Memory.
Figure 6-56. Erase screen.
FLASH MEMORY: The test readings are stored in nonvolatile
(flash) memory. The stored readings will remain until the
“ERASE” function is performed. Powering off the tester or
unplugging its battery will not affect the memory contents.
UNDERSTANDING THE READINGS: The display of the stored
readings follows the same sequence as if you reviewed the test
immediately after the test was conducted.
724-746-5500
|
blackbox.com
Page 53
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
6.6 Printing from a PC
Transfer the test readings from the Main Unit to the PC using the
supplied cable, driver and software (requires Microsoft Excel).
Figure 6-57. Printing from a PC.
STEP 1: INSTALL THE LPV DRIVER ON PC: Run “install_LPV_driv-
er.exe” (found on the LPV software CD). This driver is needed for
the PC to talk to the LPV (ignore other drivers). The LPV does
not need to be connected to the PC for the driver to properly
install.
STEP 2: TRANSFERRING TEST READINGS (LPV TO PC):
1. Connect the LPV to a USB port on your PC and turn the LPV
ON.
2. Run the “LPV.xls” spreadsheet (found on the LPV software
CD). LPV.xls is itself an Excel spreadsheet that uses built-in
Excel macros to transfer the test results to your PC. Run LPV.
xls directly from the CD or copy it to your hard drive. Follow
the directions on the Excel screen to transfer the readings
from the LPV’s printer memory.
3. If you wish, print some or all of the tests (each test prints on a
separate sheet). Or e-mail the file to your customer as proof
of test.
Page 54
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
4. Save the file using Excel's File>"Save as". See the Readme.doc
file on the LPV software CD for more details.
STEP-BY STEP INSTRUCTIONS FOR USING EXCEL:
1. After you have installed the driver and connected the LPV to
the PC, launch Excel. Select FILE, OPEN and select LPV.xls
(either from your LPV software CD or hard drive).
2. Excel asks you if you wish to “Enable macros.” Select “Enable
macros.” Say “No” if asked if you want to open as a “Read
Only” file.
Figure 6-58. Microsoft Excel screen.
3. Excel alerts you that it has not found the tester. Click ”OK”
to continue and use the Import Report routine to locate the
tester.
Figure 6-59. OK screen.
4. The Import Report screen with three buttons appears.
“Detect Testers” is automatic.
724-746-5500
|
blackbox.com
Page 55
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
Figure 6-60. Import Report screen.
5. Import Report: The LPV spreadsheet’s first step is to
automatically assign a COM (serial) port to your USB
connection and detect the LPV tester. The COM port number
selected is displayed in the window (1 through 9 is accept-
able). The "Import Reading" button will only be enabled if a
LPV tester is detected. If Detect Testers does not work, it will
respond with the error message “No Network Testers found.”
Verify the tester's power is ON and try again. If the problem
still persists, see “Error messages” below.
6. Press the Import Readings button next. It downloads data
from the serial port specified in the drop down box. Press OK.
Figure 6-61. Download succesful screen.
7. Error messages: If Excel says “Please select a serial port with a
network tester connected” or “No network testers found,”
communication is not established with the LPV’s USB port.
First check the connections: Is the USB cable firmly connect-
ed? Is Excel macro security set to low? Is the LPV powered
ON?
Page 56
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
8. After the readings are downloaded, press the “Edit Report”
button to launch the spreadsheet. If you wish to change any
NAMES that you created, do it in this opening screen. You can
wait until they are in the spreadsheet, but it is quicker here.
Figure 6-62. Edit Report screen.
9. The sequential number (1–250) automatically assigned by the
LPV to each stored test will appear as “Reading: Cable#1,
Reading: Cable#2,” etc. in the spreadsheet along with any
custom name that you created. The “Reading #” can only be
modified in the spreadsheet.
NOTE: The LPV allows duplicate custom names, but when they
are printed in Excel, they will appear as “Jack A,” “Jack A
(2),” “Jack A (3),” etc. unless you change the name here.
10. When satisfied, press Finish. The spreadsheet named “LPV.
XLS” will appear. One cable test reading occupies one work-
sheet. It works like an Excel spreadsheet (save it under a dif-
ferent name, change the names in the cells, etc.). When you
are ready to print, select FILE, PRINT and in the PRINT WHAT
dialog box select ALL. All the cable test readings will print
(one per page).
724-746-5500
|
blackbox.com
Page 57
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
Figure 6-63. LPV.XLS spreadsheet.
Typical LPV printout
NOTE: If Level 2 testing was not performed, the Data Signal
Levels and the LP Verification #2 charts will have no data.
Page 58
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
Figure 6-64. Sample LPV printout.
724-746-5500
|
blackbox.com
Page 59
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
6.7 Network Testing
Display the advertised and negotiated speeds of LAN devices
and view the signal levels of real live data.
Figure 6-65. Network ports.
Figure 6-66. “Use right jack” alert screen.
Page 60
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
NETWORK PORTS (USE RIGHT JACK): Select Network Ports to
display the capabilities of a LAN device. LAN devices broadcast
their capability in terms of speed, duplex, and other features
(termed “advertised capabilities”) to other LAN devices. When
two LAN devices are connected together, they “negotiate” to
attain the highest common denominator for communicating on
the link. For instance, a Gigabit switch with an advertised
capability of 1000 Mbps, full-duplex will negotiate down to
100 Mbps, half-duplex when connected to a 100-Mbps, half-
duplex LAN device. The LPV displays individual LAN devices
advertised capabilities and also can connect INLINE between two
LAN devices to display the negotiated results.
NOTE: The RIGHT jack is protected from PoE voltage. Use it
when connecting to devices.
6.7.1 Scan One Port
Network Testing/SCAN ONE PORT
Figure 6-67. Scan one port screen.
Figure 6-68. Scan one port application.
724-746-5500
|
blackbox.com
Page 61
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
SCAN ONE PORT: Move the cursor to SCAN ONE PORT and
press SELECT if you wish to display the advertised capability of a
LAN device. You can connect to any LAN device using a patch
cable or any cable of your choosing. The signal data levels of all
active pairs will also be displayed. When scanning one port, the
connection can be made to a live hub, switch, or PC without
affecting the communication of the other connected devices.
See the following paragraphs in this section for examples of
advertised capability and the Signal Data Level display.
Figure 6-69. Testing Link Pulses from a Gigabit device.
Figure 6-70. Testing Link Pulses from a 100-Mbps device.
The first step in the scanning process reads the link pulses of the
LAN device and displays the advertised capability. LAN devices
broadcast their capability in terms of speed, duplex, and other
features (termed “advertised” capabilities) to other LAN devices.
Page 62
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
First example (previous page): The LPV has found a Gigabit
device (1000 Mbps) on Pairs 1, 2 and 3, 6 that is capable of
transmitting at 10 Mbps, 100 Mbps, and 1000 Mbps at full-
duplex. 1000 Mbps devices use all four pairs.
In Figure 6-70, the LPV has found a 100-Mbps device on Pairs 3,
6 that is capable of transmitting at 10 Mbps and 100 Mbps at
half-duplex. Typically, devices that transmit on Pairs 1, 2 are PCs
and devices that transmit on 3, 6 are hubs and switches.
Press the down arrow key qto continue.
Figure 6-71. Signal levels of real live data from a Gigabit switch.
Figure 6-72. Signal levels of real live data
from a 100-Mbps switch.
724-746-5500
|
blackbox.com
Page 63
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
The signal level screen is a powerful tool. It is a live signal
attenuation display. If the level is below the Data Min line, you
may experience faulty transmissions. If the signal is well above
the Data Min line, you have plenty of “headroom.”
Press the down arrow qkey to continue.
The two examples here show the differences between Gigabit
devices and 10- and 100-Mbps devices. With a Gigabit device it
is possible to view real live data on all four pairs whereas a
10-Mbps and 100-Mbps device can only transmit on one pair.
A Gigabit device is a full-duplex device that uses two pairs to
transmit and two pairs to receive data, and it can be tricked into
displaying the data on the two receiving pairs. That makes it a
perfect device to get a full view of all four pairs of the cable.
Figure 6-73. Monitor inline screen.
Figure 6-74. Monitor inline application.
Page 64
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
6.7.2 Monitor Inline
Move the cursor to MONITOR INLINE and press SELECT if you
wish to view the negotiated results between two LAN devices.
NOTE: Data communication can take place while the Main Unit is
inline between two devices but after the negotiation is
complete.
The MONITOR INLINE TEST is methodical and mostly automatic.
Here is a summary of the steps that allow the LPV to arrive at the
negotiated speed (detailed steps are on the next page):
1. Plug in one PORT to the LEFT SOCKET of the LPV.
2. Pause for a few seconds and then plug the second PORT into
the RIGHT SOCKET.
3. The LPV displays the negotiated speed.
NOTE: If you suspect one of the devices has PoE, plug it into the
RIGHT jack.
Screen-by-screen instructions to perform INLINE testing.
Follow the steps and wait for the LPV directions. The tester will
tell you when it is time for the next step.
UNPLUG ALL PORTS. When the LPV senses that no ports are
connected to the tester, it will begin.
Figure 6-75. Unplug all ports screen.
PLUG IN 2 PORTS. Plug in both devices using the “LEFT” and
“RIGHT” sockets of the LPV.
724-746-5500
|
blackbox.com
Page 65
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
Figure 6-76. Plug in two ports screen.
CAPABILITY SCREEN. This screen (or similar) appears as the LPV
monitors the devices. When complete, the LPV will automatically
continue to the next screen.
Figure 6-77. Capability screen.
Figure 6-78. The negotiated speed of the link
is automatically displayed.
Page 66
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
The monitor inline test is complete. Data can be transmitted
between the two LAN devices without removing the tester.
NOTE: Most network ports negotiate to the highest possible
data rate. Some ports will negotiate to a maximum of the
last data rate used.
For example, if a PC and a switch communicate at 100 Mbps
and a new Gigabit switch is installed, the PC port may drag the
switch down to 100 Mbps, even if the PC is capable of Gigabit
data rates. This may be solved by resetting the PC. Or use the
scan one port option to read and unstick the port. If in doubt,
use the tester to scan and unstick both ports, one at a time.
6.7.3 Send Beacon
Figure 6-79. Locate cable drops by lighting a link LED.
724-746-5500
|
blackbox.com
Page 67
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Chapter 6: Operation
Figure 6-80. Scroll down and select Send Beacon.
Figure 6-81. Port beacon example.
PORT BEACON: Use the Port Beacon to locate cable connections
in crowded areas. To activate the port beacon, move the cursor
to Port Beacon and press Select. The Port Beacon is a link pulse
that the Main Unit sends to the receiving device every 3 seconds.
The Port Beacon causes the link LED to flash on the LAN device,
enabling you to spot the connection.
Page 68
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Appendix A: Straight-Through Coupler
Appendix A. Straight-Through Coupler
When installing or troubleshooting a LAN, you might need a
straight-through cable coupler. The LPV's Main Unit jacks makes
it easy. The tester must be OFF to use this feature.
Figure A-1. Straight-through coupler.
NOTE: If you suspect one of the devices is capable of sourcing
PoE voltage, connect the device to the RIGHT jack. The
RIGHT jack is protected from PoE voltage.
724-746-5500
|
blackbox.com
Page 69
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Appendix B: Ping and TCP/IP Debugging Tools
Appendix B. Ping and TCP/IP Debugging Tools
What is TCP/IP: TCP/IP is set of standards first developed by
ARPA (USA DOD’s Advance Research Projects Agency) that
define how information is routed over the Internet. And because
of its Internet popularity, TCP/IP is the most popular protocol
operating over twisted-pair cabling and therefore is the most
popular protocol used by Ethernet (the standard for local area
networking).
Why learn about TCP/IP: Once the LPV has established that
your cables and network devices are working at the hardware
level, your next step is to check out the software level of your
network. Understanding the basics of TCP/IP and gaining a
familiarity with your operating system's built-in network
debugging tools helps you diagnose and troubleshoot network
problems at the software level.
TCP/IP basics: TCP/IP has 4 layers:
1. The lowest layer is the Physical layer that deals with cabling.
2. The next layer is the Internet layer. This is the IP layer (internet
protocol) and it describes the assigning of an IP address to
each data packet that is transmitted (all data on the internet
must have a destination address associated with it and this is
referred to as an IP address. The address can refer to a
workstation on your local network or a server on the Internet
thousands of miles away.
3. The next layer is the Transport layer. Because data packets can
travel through networks and the Internet using many different
routes, they will not necessarily arrive in the same order as
they were sent. There needs to be a mechanism that reassem-
bles the packets in the proper sequence. This is the job of the
“TCP” (transmission control protocol), and it resides in this
layer.
4. Layer 4, the highest layer, is the Application layer. This is
where Ethernet and many other software tools reside.
Page 70
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Appendix B: Ping and TCP/IP Debugging Tools
Because TCP/IP is so common, Windows® and many UNIX®
systems have built-in tools to help you debug TCP/IP network
problems.
These debugging programs are executed at the command line
prompt of the operating system (see the end of this section for
more information about the command line).
ping
The most popular TCP/IP debugging program is called “ping”
(after the name given to the operation of submarine sonar
devices). Like the sonar, ping sends out a packet to an address
that you specify and waits for a reply. Although very simple to
use, ping is extremely powerful because it works at the IP level
and often will respond even when the higher level TCP layer
cannot. As mentioned above, pinging capability is included
with most systems and there are also many shareware
implementations.
USE: Determine if a workstation is connected to the network.
Routers, servers, and workstations are identified by an IP address
and possibly a “name.” The IP address is a numeric string whose
format is referred to as “dotted decimal” (example:
192.168.0.0.). The “name” can be any name given to a
computer when it is installed or an internet URL. The ability to
use a name is provided by a server’s DNS (Domain Name
Service). The DNS has a lookup table that cross references IP
addresses to names. If a DNS service is not available, you will
need to use the IP address.
EXAMPLE OF USE:
#1: You have problems connecting to the Black Box Web site
from a workstation, and you know the DNS name of the
connected, you will receive back blackbox.com's IP address
(for example, 207.115.64.64) and the roundtrip time of your
ping packet.
724-746-5500
|
blackbox.com
Page 71
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Appendix B: Ping and TCP/IP Debugging Tools
#2: You are having a problem with one of your workstations
communicating to a server. You know the server's IP address
is 192.168.1.100. I enter “ping 192.168.1.100”on the
workstation’s command line. If the server is connected, you
will receive a response to your ping.
NOTE: It’s easy to find a computer’s IP address. Go to the target
computer (the one you wish to ping) and on its command
line enter “ipconfig.” The IP address (and other addresses)
will be displayed. More information on the ipconfig
command can be found later in this section.
The Ping program has endless uses. Ping an address (as above):
If you get a response using the IP address but do not get a
response using the DNS address, there must be a problem with
the DNS system. If you suspect this, try another debugging pro-
gram “nslookup.” On the command line, enter nslookup fol-
lowed by the DNS name (enter nslookup www. blackbox.com)
and see if the IP address is displayed. If it is, your DNS appears to
be working correctly. Ping yourself: You can use the ping com-
mand to ping yourself, either using your own IP address or what
is known as the loopback address. The loopback address is a
special reserved address that works on all systems:127.0.0.1
(enter ping 127.0.0.1). If you would like to try pinging your own
workstation address but do not know it use the “ipconfig”
command (in the next section). Pinging yourself is the first test
that should be conducted because if it fails, it most likely means
that TCP/IP is not properly loaded on the workstation. If it passes
and you were using your own IP address (not the loopback
address), it confirms that you are the only one on the network
with that address. Ping your gateway: If you get a response, it
means that the packets are making it to the router (a gateway is
a device on a network that serves as an entrance to another net-
work). On business LANs, the gateway is generally the router. In
homes, the gateway is the Internet service provider (ISP) that
connects the user to the Internet.
Page 72
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Appendix B: Ping and TCP/IP Debugging Tools
Ping notes: If you want to ping another workstation or server
and you do not know its DNS name or IP address use ipconfig
(below). To learn all the ping command’s option, enter ping /?.
ipconfig
USE: Determine the IP address and other related information
about a workstation. Enter ipconfig /? at the prompt to display
the options possible with this command. The two most common
entries: ipconfig and ipconfig/all.
EXAMPLES OF USE: You want to ping a remote server but you
do not know its IP address. Go to the server and at the
command line prompt enter “ipconfig.” The server's IP address
will be displayed. Return to the earlier workstation and perform
the ping test to this address.
tracert
USE: Determines how many router hops a packet took to reach
its destination. This can help determine why a network is slow
(or not functioning). Enter tracert /? at the prompt to display
the options possible with this command.
EXAMPLES OF USE: I want to determine how many routers are
between my system and my ISO. Enter tracet followed by the
name or IP address of the destination system.
Netstat
USE: Displays the current status of all listening TCP/IP ports.
A TCP/IP port is where applications connect to the server or
workstation.
EXAMPLES OF USE: You would like to see how many applica-
tions are tied to your system that use TCP/IP.
724-746-5500
|
blackbox.com
Page 73
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Appendix B: Ping and TCP/IP Debugging Tools
Executing troubleshooting programs from the command
line:
All the programs discussed must be executed from the com-
mand line of your operating system. To reach the command line
on Windows 95 and 98 systems, click on START>PROGRAMS
and Select the MS-DOS® prompt. Then enter your command.
On Windows XP systems, click on START>PROGRAMS> and
select ACCESSORIES then COMMAND LINE. Then enter your
command.
On other systems, select “Run” from the main menu and enter
“cmd.” Then enter your command.
TO EXIT THE COMMAND LINE: Enter EXIT.
Additional information:
The Web has many interesting articles on network
troubleshooting and also numerous sites that feature a glossary
of terms. Use your favorite search engine and search for Pinging,
Pinging Devices, Network Management, Network Monitoring
Tools, Network Testing, etc.
Page 74
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Appendix C: Examples of UTP Cable Faults
Appendix C. Examples of UTP Cable Faults
A good cable: A cable that passes its first set of cable tests will
have summary screen similar to this:
Figure C-1. Length/Timing summary screen of a good cable.
Bad cable (Split pair): If errors are found, they will be displayed.
Here are some examples of screens with bad cables.
Figure C-2. Bad cable: Split pairs at 154 feet.
724-746-5500
|
blackbox.com
Page 75
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Appendix C: Examples of UTP Cable Faults
The screen shows a 330-foot cable with split pairs at 154 feet. If
the cable goes through a wiring closet, it is possible the split
pairs are in the closet (154 feet away). This screen shows one of
the advantages the LPV has over testers costing thousands of
dollars more. The LPV shows the distance to the split pair to help
locate it and facilitate repair. High-cost certifiers display dBs of
crosstalk but do not help you locate the repairable split pair
fault. Turn on the trace tones and use the probe to locate the
cable in the wiring closet. Test each cable associated with the
link (patch cables, etc).
Bad cable (Near end shorts): The error is displayed as follows:
Figure C-3. Bad cable: near-end short.
The SHORT on 12> is most likely at the connector (near end). If
the short is on the far end of the cable it would look like this:
Figure C-4. Bad cable: far-end short
Page 76
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Appendix C: Examples of UTP Cable Faults
Opens in cable pairs generate errors in both in skew tests and in
wire map tests. The following example shows a 200-foot cable
with a break in the middle on Pair 78. The following is the fi rst
screen to show a problem.
Figure C-5. Bad cable: Open.
NOTE: There are two problems shown. The skew (difference
in delay between pairs) is much greater than 50 ns.
Another problem is that the cable length is only shown as
98 feet. Press details and continue the tests. All will
become clear when cable map is displayed. Here is a
sample cable map.
Figure C-6. Bad cable: Wire map of open pair.
The sample map clearly shows the problem. There is an open at
98 feet on Pair 78. The skew was so large because the timing
pulses travel about 200 feet on Pairs 12, 36, and 45, but only
travel 98 feet on Pair 78. As always, retest cable after repairs are
made.
724-746-5500
|
blackbox.com
Page 77
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Appendix C: Examples of UTP Cable Faults
During the wire map test, you probably noticed that the indica-
tor lights on the remote probe (connected to the far end of the
cable) continue to flash. This is another indication of a problem.
If a cable has a short in the middle, the wire map looks like this:
Figure C-7. Bad cable: wire map of shorted pair.
The LPV is both a LP verifier and troubleshooting tool. It
identifies the faults and gives you the distance to the opens,
shorts, and split pairs.
Page 78
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Appendix D: Making a Correct UTP Cable
Appendix D. Making a Correct UTP Cable
Twisted-Pair Cables: Unshielded twisted-pair cable is used for
BASE-T applications because it is inexpensive, easy to use, and
has excellent noise-canceling capabilities. A minimum of two
pairs of twisted-pair wire are required for each computer that
connects to the local area network:
• One pair of twisted-pair wire to transmit data.
• One pair of twisted-pair wire to receive data.
There are exceptions. 100BASE-T devices (called “T4”) require
four pairs of wires. Also, Gigabit devices (1000 Mbps) require
four pairs. In both cases, two pairs are used for transmit and two
for receive.
As mentioned above, twisted-pair cable has separate pairs of
wires twisted together to minimize crosstalk. If a wiring error is
made and one pair of wire is “split” with another (“split pairs”),
the excess crosstalk will most likely keep the link from operating
properly.
To make a proper cable, first choose a twisted-pair cable that
is adequate for your application. For instance, CAT5e cable for
100-Mbps and 1000-Mbps applications. Use solid-core wire
when pulling inside a wall. Use stranded cable (“patch cable”)
for jumpers.
• Remove the outer jacket of the twisted-pair cable, exposing
about a 6 feet of wire on each end of the cable.
• Each pair of wire must be twisted together (after crimping, the
wire should be twisted right up to the connector).
• Do not make the number one wiring mistake: “Split pairs” (a
wire from one pair is swapped with a wire from another pair).
• To minimize mistakes, use a standard color code throughout
your project. See the following page for the correct connector
pin numbers associated with each BASE-T pair.
724-746-5500
|
blackbox.com
Page 79
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Appendix D: Making a Correct UTP Cable
• Use good-quality connectors and tools.
RJ-45 Connectors (sockets and plugs): The BASE-T Standard uses
RJ-45 sockets and plugs. The RJ-45 socket has eight pins. The
pins are numbered 1 to 8. Looking at the socket with insertion
key facing down, Pin Number 1 is to the left.
Figure D-1.
Colors: The first color is the base color on the cable. Second
color is the stripe color of the cable. A straight-through cable has
identical ends.
NOTE: The above color code is the most popular in use.
Page 80
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
NOTES
724-746-5500
|
blackbox.com
Page 81
ownload from Www.Somanuals.com. All Manuals Search And Downloa
NOTES
Page 82
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
NOTES
724-746-5500
|
blackbox.com
Page 83
ownload from Www.Somanuals.com. All Manuals Search And Downloa
Black Box Tech Support: FREE! Live. 24/7.
Tech support the
way it should be.
Great tech support is just 30 seconds away
at 724-746-5500 or blackbox.com.
About Black Box
Black Box provides an extensive range of networking and infrastructure
products. You’ll find everything from cabinets and racks and power and
surge protection products to media converters and Ethernet switches all
supported by free, live 24/7 Tech support available in 30 seconds or less.
© Copyright 2011. Black Box Corporation. All rights reserved.
TS580A-R4, version 1
724-746-5500
|
blackbox.com
ownload from Www.Somanuals.com. All Manuals Search And Downloa
|