RM5100A
RM5110A
Zone 4 Seismic Cabinets, 45U
These 40" deep and 32" deep cabinets meet
Zone 4 seismic requirements.
Hold up to 2500 pounds of equipment.
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax
724-746-0746 • Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence,
Customer
Support
Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Table of Contents
1. Specifications ......................................................................................... 4
2. Overview .............................................................................................. 6
2.1 Introduction ..................................................................................... 6
2.2 Features............................................................................................ 6
2.3 What‘s Included............................................................................... 7
2.4 What You Need to Supply ............................................................... 7
2.5 Hardware Description....................................................................... 8
3. Installing the Mounting Plates in the Cabinet............................................ 9
4. Troubleshooting........................................................................................11
4.1 Contacting Black Box ......................................................................11
4.2 Shipping and Packaging..................................................................11
Page 3
724-746-5500 | blackbox.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Specifications
1. Specifications
Cable Entry Ports — (2) on top of cabinet with caps and grommets
Exterior Height — 84.05" (213.5 cm)
Exterior Width — 27.55" (70 cm)
Exterior Depth — RM5100A: 39.37" (100 cm);
RM5110A: 31.5" (80 cm)
Finish — RAL 9005 textured low-gloss black polyester powder paint coating
inside and out; smoke gray acrylic window in reinforced front door
Frame — Heavy gauge welded steel frame with (6) rack angle mounting struts
Interior Width — 19" (48.3 cm)
Number of Fan Cutouts — (2) with finger guards
Rack Angle Holes — RM5100A: M6 square;
RM5110A: 10-32 tapped
Rack Units — 45U
Standards — NEBS™ Telcordia GR-63-CORE Zone 4: Tested with 1000 lb.
(453.6 kg) of equipment installed and 100 lb. (45.4 kg) of simulated cable
weight on the top; Meets California Building Code (CBC) requirements
Weight Capacity — Dynamic: 1100 lb. (499 kg);
Static: 2500 lb. (1134 kg)
Page 4
724-746-5500 | blackbox.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Specifications
Figure 1-1. Top dimensions.
Figure 1-2. Front and side dimensions.
Page 5
724-746-5500 | blackbox.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Overview
2. Overview
2.1 Introduction
The Zone 4 Seismic Cabinet protects servers, networking equipment, and
telephony equipment through Zone 4 seismic activity. It’s made of heavy-gauge
welded steel and supports up to 2500 pounds (1134 kg) of equipment. The
cabinet is also ideal for use in high vibration areas or areas with high load
capacities. It conforms to EIA standards for 19" equipment mounting. Use it in
different applications with 19-inch rackmount equipment and fans.
The top of the cabinet features two cable entry ports with caps and grommets,
and two fan-ready cutouts with finger guards. With its “chimney” effect, the
cabinet cools mounted equipment by drawing cool air through louvers and
venting the heated air through the top.
Two models are available:
• RM5100A: 39.37" deep Zone 4 Seismic Cabinet with M6 square mounting rails
• RM5110A: 31.5" deep Zone 4 Seismic Cabinet with 10-32 tapped mounting rails
Mounting hardware is not included.
2.2 Features
• Both front and rear doors are hinged left and equipped with keylock flush
handle and three-point latching.
• Same key provides access to all doors and side panels.
• Doors and side panels can be removed for easier equipment installation and
upgrades.
• Vented, heavy gauge steel base is designed to bolt to floor with seismic-rated
fasteners.
• Has louvers on lower 1⁄3 of rear door for ventiliation.
• The cabinet ships fully assembled.
Page 6
724-746-5500 | blackbox.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Overview
2.3 What’s Included
RM5100A:
• 84.05"H x 27.55"W x 39.37"D Zone 4 Seismic Cabinet
• (2) sets of painted rack angles with M6 holes per EIA spacing (5⁄8" x 5⁄8" x 1⁄2")
• (4) mounting plates
• This user‘s manual
RM5110A:
• 84.05"H x 27.55"W x 31.5"D Zone 4 Seismic Cabinet
• (2) sets of painted rack angles with 10-32 tapped holes per EIA spacing (5⁄8" x
5
⁄
8" x 1⁄2")
• (4) mounting plates
• This user‘s manual
2.4 What You Need to Supply
• 1⁄2" high-strength mounting hardware
Page 7
724-746-5500 | blackbox.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Overview
2.5 Hardware Description
Figure 2-1 shows the components of the cabinets.
Figure 2-1. Cabinet components.
Page 8
724-746-5500 | blackbox.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Installing the Mounting Plates in the Cabinet
3. Installing the Mounting Plates in the Cabinet
The cabinet ships fully assembled, but you will need to use the (4) mounting
plates (included) with 1⁄2" high-strength mounting hardware (not included) to
install equipment in the cabinet.
Figure 3-1. Mounting plates (1, included) and hardware (2, not included).
Page 9
724-746-5500 | blackbox.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Installing the Mounting Plates in the Cabinet
Figure 3-2 shows how to install the mounting plates in the cabinet.
Figure 3-2. Installing the mounting plates in the cabinet.
Page 10
724-746-5500 | blackbox.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Troubleshooting
4. Troubleshooting
4.1 Contacting Black Box
If you determine that your cabinet is malfunctioning, do not attempt to alter or
repair the unit. It contains no user-serviceable parts. Contact Black Box Technical
Support at 724-746-5500 or [email protected].
Before you do, make a record of the history of the problem. We will be able to
provide more efficient and accurate assistance if you have a complete description,
including:
• the nature and duration of the problem.
• when the problem occurs.
• the components involved in the problem.
• any particular application that, when used, appears to create the problem or
make it worse.
4.2 Shipping and Packaging
If you need to transport or ship your cabinet:
• Package it carefully. We recommend that you use the original container.
• If you are returning the unit, make sure you include everything you received
with it. Before you ship for return or repair, contact Black Box to get a Return
Authorization (RA) number.
Page 11
724-746-5500 | blackbox.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Black Box Tech Support: FREE! Live. 24/7.
Tech support the
way it should be.
Great tech support is just 30 seconds away at
724-746-5500 or blackbox.com.
About Black Box
Black Box provides an extensive range of networking and infrastructure products.
You’ll find everything from cabinets and racks and power and surge protection
products to media converters and Ethernet switches all supported by free, live 24/7
Tech support available in 30 seconds or less.
© Copyright 2012. Black Box Corporation.
RM5100A, version 1
724-746-5500 | blackbox.com
Download from Www.Somanuals.com. All Manuals Search And Download.
|