ProHeat 2X™
™
Healthy Home
U S E R ’ S G U I D E
66Q4 anD 73a5 SERIES
3
Safety Instructions
4-5 Product View
6
Assembly
7-9 Special Features
9-17 Operation
17-19 Maintenance and Care
19-21 Troubleshooting
21 Consumer Services
22-23 Replacement Parts
24 Warranty
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
■
■
■
■
■
When using an electrical appliance, basic precautions
should be observed, including the following:
Keep appliance on a level surface.
Turn off all controls before unplugging.
Unplug before attaching the TurboBrush™.
Be extra careful when cleaning stairs.
Close attention is necessary when used by or
near children.
Read all instructions before using your ProHeat 2X™
WaRnInG:
To reduce the risk
of fire, electric shock, or injury:
■
■
■
■
■
Do not immerse.
SaVE THESE
InSTRUCTIOnS.
Use only on surfaces moistened by cleaning process.
Always connect to a properly grounded outlet.
See Grounding Instructions.
THIS moDEL IS foR HoUSEHoLD USE onLy.
Commercial use of this unit voids the
manufacturer’s warranty.
Unplug from outlet when not in use and before
conducting maintenance or troubleshooting.
Do not leave machine when it is plugged in.
Do not service machine when it is plugged in.
Do not use with damaged cord or plug.
If appliance is not working as it should, has been
dropped, damaged, left outdoors, or dropped into
water, have it repaired at an authorized Service Center.
Use indoors only.
Do not pull or carry by cord,use cord as a handle,close
door on cord,pull cord around sharp corners or edges,run
appliance over cord,or expose cord to heated surfaces.
Unplug by grasping the plug, not the cord.
Do not handle plug or appliance with wet hands.
Do not put any object into appliance openings, use with
blocked opening, or restrict air flow.
■
■
■
■
GROUnDInG InSTRUCTIOnS
This appliance must be connected to a grounded
wiring system. If it should malfunction or break
down, grounding provides a safe path of least
resistance for electrical current, reducing the risk of
electrical shock. The cord for this appliance has an
equipment-grounding conductor and a grounding
plug. It must only be plugged into an outlet that is
properly installed and grounded in accordance with
all local codes and ordinances.
■
■
■
■
■
Grounded
Outlets
■
Do not expose hair, loose clothing, fingers or body
parts to openings or moving parts.
■
■
Do not pick up hot or burning objects.
Do not pick up flammable or combustible materials
(lighter fluid, gasoline, kerosene, etc.) or use in the
presence of explosive liquids or vapor.
Grounding Pin
■
Do not use appliance in an enclosed space filled with
vapors given off by oil base paint, paint thinner, some
moth proofing substances, flammable dust, or other
explosive or toxic vapors.
Do not pick up toxic material (chlorine bleach,
ammonia, drain cleaner, gasoline, etc.).
Do not modify the 3-prong grounded plug.
Do not allow to be used as a toy.
Do not use for any purpose other than described in
this User’s Guide.
Do not operate the appliance unless the belt door is
securely assembled in the location provided.
Do not unplug by pulling on the cord.
Use only manufacturer’s recommended attachments.
Always install float before any wet pick up operation.
Use only cleaning products formulated by BISSELL for
use in this appliance to prevent internal component
damage. See the cleaning fluid section of this guide.
Keep openings free of dust, lint, hair, etc.
Do not point attachment nozzle at people or animals
WaRnInG:
Improper
connection of the equipment-grounding
conductor can result in a risk of electrical
shock. Check with a qualified electrician
or service person if you aren’t sure if the
outlet is properly grounded. DO nOT MODIFY
THE PLUG. If it will not fit the outlet, have a
proper outlet installed by a qualified electri-
cian. This appliance is designed for use on a
nominal 120-volt circuit, and has a ground-
ing attachment plug that looks like the plug
in the drawing above. Make certain that the
appliance is connected to an outlet having
the same configuration as the plug. no plug
adapter should be used with this appliance.
■
■
■
■
■
■
■
■
■
■
■
3
w w w . b i s s e l l . c a
1 - 8 0 0 - 2 6 3 - 2 5 3 5
Download from Www.Somanuals.com. All Manuals Search And Download.
™
CleanShot
Trigger
Spray Trigger
Heater Switch
Product view
R
I
Power Switch
Extra Long
Power Cord
Flex Hose
Upper Handle
Easy Carry Handle
Heat
Indicator Light
Tank Carry
Handle
™
ReadyTools
Dial
Detent Pedal
Lower Base
2-in-1 Water Tank
™
CleanShot
™
Dry Aire
™
Edge Sweep Brushes
Easy To Remove
Nozzle
w w w . b i s s e l l . c a
1 - 8 0 0 - 2 6 3 - 2 5 3 5
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Product view
Spray Trigger
Upper Hose Rack
Hose Secure
Latch
Upper Handle
™
TurboBrush
Storage
Crevice Tool Holder
Lower Hose Rack
Lower Base
WaRnInG:
To reduce the risk of fire and
electric shock due to internal
component damage, use only
BISSELL cleaning fluids intended
for use with the deep cleaner.
non-BISSELL cleaning solutions
may harm the machine and void
the warranty.
Detent Pedal
Formula Tank
Cleaning fluid
Keep plenty of genuine BISSELL 2X Multi-allergen Formula on hand so you can clean and protect
whenever it fits your schedule. always use genuine BISSELL deep cleaning formulas. non-BISSELL
cleaning solutions may harm the machine and will void the warranty.
BISSELL
2X Hard
Floor
Solutions
Formula
BISSELL
BISSELL
Tough Stain
PreCleaner
BISSELL
2X Multi-Allergen
Removal
Formula with
Scotchgard™
Protection
BISSELL
BISSELL
2X Fiber
Cleansing
Formula with
Scotchgard
Protection
2X Pet Stain and
Odor Removal
Formula with
Scotchgard™
Protection
2X Professional
Deep Cleaning
Formula with
Scotchgard™
Protection
5
w w w . b i s s e l l . c a
1 - 8 0 0 - 2 6 3 - 2 5 3 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
WaRnInG:
Do not plug in your
cleaner until you have
completely assembled it per
the following instructions
and are familiar with all
instructions and operating
procedures.
Your ProHeat 2X comes in three, easy to
assemble components:
Upper Handle
Lower Handle
Tool Caddy
The only thing you will need to assemble your
cleaner is a Phillips head
screwdriver.
1. Slide upper handle onto lower handle.
2. Screw 3 screws into the marked holes.
1.
3.
2.
4.
3. Place upper hose rack onto back of upper
handle, and secure with tapered screw.
4. Place lower hose rack onto back of upper
handle by pushing in and sliding down until
it snaps into place.
5. Snap tools into the tool caddy as shown in
figure 5.
6. Wrap power cord and flex hose as shown in
figure 5.
7. Keep flex hose snugly in place by using
the hose secure latch.
ProHeat 2X assembly is now complete.
5.
Tough
Stain Brush
Crevice Tool
Holder
TurboBrush
Spraying
Crevice Tool
7.
Hose Secure
Latch
w w w . b i s s e l l . c a
1 - 8 0 0 - 2 6 3 - 2 5 3 5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Special features
Your BISSELL ProHeat 2X deep cleaner is a home
cleaning system that uses the power of heat,
brushes and cleaning formula to get the deep
down dirt for a maximum clean. not only does it
come with a lot of unique features, it has been
designed with you, the customer, in mind.
Built-in-Heater feature
BISSELL ProHeat 2X models all feature a patented
built-in heater which will heat the hot tap water
you put in up to 25 F degrees (14oC) hotter to
safely optimize cleaning effectiveness. The heater
will never allow the temperature to exceed 190 F
degrees (88oC). The heater switch on the front of
the machine controls the heater so you have the
option to turn off the heat if you are cleaning
delicate wool or oriental rugs.
Dual DirtLifter™ PowerBrushes
The two DirtLifter PowerBrush rolls are
designed to enhance cleaning performance.
The bristle pattern safely lifts out the deep
down dirt while gently grooming carpet fibers.
The floating suspension self-adjusts to all
carpet heights. Once the product is in the
upright position, the brushes automatically
stop spinning.
Custom Clean™
The Custom Clean feature automatically mixes
hot tap water with the BISSELL formula. Simply
choose one of the 4 settings (heavy traffic,
normal clean, light clean, or water rinse) and the
ProHeat 2X will adjust the right amount of
cleaning solution to mix with the heated water to
fit your cleaning need.
Having a separate solution tank from the water
tank also allows no waste of formula. Because the
water and solution are stored separately, they are
not mixed until you are ready to clean. When your
cleaning job is finished, the formula can be stored
ready to use in your machine for the next time!
(located on upper handle)
7
w w w . b i s s e l l . c a
1 - 8 0 0 - 2 6 3 - 2 5 3 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Special features
CleanShot™
The CleanShot feature gives you the ability to
tackle tough stains with the push of a button.
Cleaning solution is sprayed in a concentrated
stream, penetrating the stain and allowing for
better cleaning focus. Simply spray and
suction and the stain is gone! CleanShot is
especially effective for spots and stains that
would otherwise take a lot of deep cleaning
cycles to remove. It allows the cleaning
formula and machine to do the work for you.
Flow Gauge
™
Dry Aire
The Dry aire system spreads hot air across the
carpet to aid in drying. The feature runs while
your machine is powered. Heated air is distributed
from the bottom and back of the machine and
blown across the carpet while you clean!
®
CleanShot
™
Flow Gauge
Dry Aire
The flow gauge is located on the rear cover of
your unit and is a convenient performance
feedback indicator.
The flow gauge will spin when the trigger is
depressed and:
• There is liquid in both the clean water tank
and the formula tank
OR
• Custom Clean is set to rinse and there is
water in the clean tank
The flow gauge will stop spinning when:
• The trigger is let go
• The unit runs out of clean water
• The unit runs out of cleaning formula
2-in-1 water tank
Our 2-in-1 water tank full capacity system is
designed with a heavy duty bladder inside for clean
water. as you clean, the clean water in the bladder
will empty and mix with the cleaning formula. Dirty
water pulled out of your carpets will collect around
the outside of the bladder so that clean and dirty
water are always kept separate. This allows the
user to maximize tank space, yet only carry one
tank to and from the sink for emptying and filling.
w w w . b i s s e l l . c a
1 - 8 0 0 - 2 6 3 - 2 5 3 5
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Special features
Easy to remove and clean nozzle
now, cleaning up your machine after the
cleaning process is easier than ever! Simply
remove the 2-in-1 Tank and remove the screw
to pop out the nozzle for rinsing in the sink. Dirt,
loose carpet fibers and remaining pet hair or
fuzz get washed away in a snap.
™
ReadyTools dial
This provides either floor cleaning or above floor
cleaning with the turn of a knob. If choosing
above floor cleaning for upholstery, stairs, or for
those creases close to the baseboards, turn knob
to "TOOLS" and choose the attachment
appropriate for the job. attach tool to the flex hose
and you are ready to go. Be sure to turn knob
back to "FLOOR CLEanInG" when done.
™
Scotchgard Protector
Carpet protection applied at the mill typically
wears down over time from heavy foot traffic
and everyday cleaning, including deep cleaning.
To help restore this important protection, only
BISSELL offers deep cleaning formulas with
Scotchgard protector. This offers extra protection
against dirt and tough stains to keep your carpets
looking good longer.
To maintain your Scotchgard 5-year limited stain
warranty, you no longer are required to hire a
professional. By using your BISSELL ProHeat
machine with BISSELL formulas containing
Scotchgard protector every 12 months, your carpet
warranty from 3M remains in effect. no other home
deep cleaning system can do this for you. Refer to
the Scotchgard protector warranty for details.
Operation
Before you clean
1. Plan activities to give your carpet time to dry.
B
U
H
S
C
I
N
2. Move furniture to another area if cleaning
9
10
XIT
8
1
1
an entire room (optional).
3’
12
7
1
T
AR
ST
HERE
6
5
2
3
3. Vacuum area with a dry vacuum cleaner
4
thoroughly before deep cleaning.
4. Plan your cleaning route to leave an exit path. It
is best to begin cleaning in the corner farthest
from your exit.
9
w w w . b i s s e l l . c a
1 - 8 0 0 - 2 6 3 - 2 5 3 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Before you clean (continued)
aTTEnTIOn:
5. Pretreating (optional)
Some Berber carpets have a
tendency to fuzz with wear.
Repeated strokes in the same
area with an ordinary vacuum
or deep cleaner may aggravate
this condition. Please see Stain
Removal instructions on page 15.
Pretreating is recommended to improve cleaning
effectiveness for heavily soiled carpet in high
traffic areas such as entryways and hallways.
Option a: BISSELL Tough Stain PreTreat
a. Spray the BISSELL Tough Stain Pre-treat
formula onto heavy traffic areas, soiled
areas, or stains.
B. Allow to penetrate for at least 3 minutes.
C. Clean as normal, using the BISSELL
ProHeat 2X machine on the high traffic
setting, following the instructions below.
Option B: CleanShot™
a. Set Custom Clean for the desired setting.
1.
1a.
B. Press the CleanShot button and aim the
focused stream onto the stain. Allow the
formula to soak in for 30 seconds.
C. Run the machine over the stain to extract.
Repeat as needed until the stain is gone.
D. Rinse if desired.
1b.
1c.
Carpet cleaning
1. Fill the 2-in-1 Water Tank. Remove the tank
from the base of the machine by lifting up the
tank carry handle. Carry like a bucket to the sink.
1a. Unlatch the top of the tank from the bottom
by lifting up on the tank latch which is located
on the back of the tank.
1d.
1b. Remove the top of the tank by lifting up on
the handle.
Lip
note how the lip on the top tank separates
from the groove in the bottom tank. This
placement is important when putting the
tank back together
Groove
(underside of
bottom tank)
1c. Fill the heavy duty bladder with clean hot
tap water.*Do not boil or microwave water
as it can destroy the bladder.
1e.
1d. Leaving the filled bottom of the tank on a
flat surface, only maneuver the top of the
tank. To attach the top part of the tank to the
bottom, carefully hook the lip on the top tank
into the groove on the bottom tank.
1e. Fasten tanks together by securing the latch
in the back.
note: Remember to secure the tank latch in
the back and test to make sure it is secure
before picking up the tank.
w w w . b i s s e l l . c a
1 - 8 0 0 - 2 6 3 - 2 5 3 5
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Carpet cleaning (continued)
1. Remove formula tank from back of machine.
2. Fill the formula tank by first unscrew-
ing the cap and insert. Always use genuine
BISSELL formulas to maximize cleaning and
for the safety of your machine. Fill water up to
water line, and then fill up to formula line with
BISSELL 2X concentrated formula. Replace the
cap and insert. Place formula tank into the slot
in the back of the machine for a snug fit.
1.
2a.
3. Set Custom Clean Dial. Simply choose one
of the 4 settings (heavy traffic, normal clean,
light clean, or water rinse) and the ProHeat
2X will adjust the right amount of cleaning
solution to mix with the heated water to fit
your cleaning need.
3.
4.
FLOOR
CLEANING
4. Set ReadyTools Dial to the floor cleaning setting.
5. Plug into a proper outlet and turn the power
and heater switches to the ON ( I ) position.Allow
1 minute for the built-in heater to warm-up before
cleaning.The ProHeat 2X will be fully warmed and
will provide optimal performance after a minute of
continuous heated cleaning.
5.
6. Cleaning Strokes. While pressing the trigger,
make one slow forward wet pass and another
one back. Let the built-in heater, formula, and
DirtLifter PowerBrushes do the work for you.
Caution: Do not overwet. Take care not to run
over loose objects or edges of area rugs. Stalling
brush may result in premature belt failure.
Power Switch
Heater Switch
note: Your machine is equipped with a
circuit breaker that will automatically shut
off the brush if a large or loose object is
caught in the brush roll. If that happens, be
sure to unplug your machine, remove the
foreign object, and then plug the machine
back in to reset the circuit breaker.
Release the trigger and make one slow
forward and backward pass over the same
area to remove any residual dirty water and
aid in drying. Repeat cleaning passes until
solution being pulled up appears clean.
Continue passes without pressing the trigger
until you can’t see any more water
WaRnInG:
To reduce the risk of fire and
electric shock due to internal
component damage,use only
BISSELL cleaning fluids intended
for use with the deep cleaner.
Keep plenty of genuine BISSELL 2X
Multi-allergen Removal Formula on
hand so you can clean whenever it fits
your schedule. always use genuine
BISSELL deep cleaning formulas. non-
BISSELL cleaning solutions may harm
the machine and void the warranty.
being pulled up.
11
w w w . b i s s e l l . c a
1 - 8 0 0 - 2 6 3 - 2 5 3 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Carpet cleaning (Continued)
6. after cleaning, you may want to turn the Custom
Clean dial to rinse to give your carpeting a final
water only rinse. This will ensure thorough
removal of embedded dirt loosened by the deep
cleaning formula. BISSELL deep cleaning for-
mulas contain an anti-resoiling agent that helps
your carpets repel dirt and keeps them look-
ing good longer.
7. Remove the tank from the base of the machine
by lifting up on the tank carry handle. Carry like a
bucket to a utility sink or outside where you will
dispose of the dirty water.
7.
7a.
7a. Unlatch the top of the tank from the bottom by
lifting up on the tank latch which is located on the
back of the tank.
7b. Remove the top of the tank by lifting up on the
handle.
7b.
7c.
note how the lip on the top tank separates
from the groove in the bottom tank. This
placement is important when putting the
tank back together.
7c. Lift the bottom portion of the tank; pour out dirty
water toward the sink through the triangular
shaped opening in the corner of the tank.
note: You may notice hair & debris deposits on the
carpet or in the tank that were loosened by the
cleaning action (especially with newer carpets that
have never been deep cleaned before).This debris
should be picked up and thrown away.
8.
7d.
7d. Fill the heavy duty bladder with clean hot tap
water, following instructions 1c through 1e on
page 10.
note: Remember to secure the tank latch in
the back and test to make sure it is secure
before picking up the tank. always check
the level of cleaning formula in the formula
tank at the same time, and refill as needed.
8. Water rinse (Optional). Rinsing is an optional
step that can be done during the cleaning pro-
cess by switching from one of the clean
settings on the Custom Clean dial to a water rinse
setting, or it can be done after the carpeted area
has been cleaned. Simply choose the water rinse
setting on the custom clean dial, and follow the
same path as you did for cleaning, taking care
to do a forward (wet) stroke by depressing the
trigger, a backward (wet) stroke, and a forward
and backward (dry) stroke, releasing the trigger.
Continue this until the water you see coming up
the nozzle is clear.
w w w . b i s s e l l . c a
1 - 8 0 0 - 2 6 3 - 2 5 3 5
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Carpet cleaning (Continued)
9. CleanShot. CleanShot is an optional feature
that can be used to fight tough stains. It can
be used as either a tough stain pre-treat (see
page 10) or can be used during the deep
cleaning process itself. To use CleanShot either
as a pre-treat or during deep cleaning, follow
the instructions below.
a. Set Custom Clean for the desired setting.
B. Press the CleanShot button and aim the
focused stream onto the stain. Allow the
formula to soak in for 30 seconds.
C. Run the machine over the stain to extract.
Repeat as needed until the stain is gone.
D. Rinse if desired.
Cleaning with attachments
Your ProHeat 2X machine comes equipped with
a hose and at least one attachment for cleaning
stairs, upholstery, and more.
1. Important! If using to clean upholstery,
check upholstery tags.
a. Check manufacturer’s tag before cleaning.
“W” or “WS” on the tag means you can
use your ProHeat 2X. If the tag is coded
with an “X” or an “S” (with a diagonal stripe
through it), or says “Dry Clean Only”, do not
proceed with any deep cleaning machine.
Do not use on velvet or silk. If manufactur-
er’s tag is missing or not coded, check with
your furniture dealer.
B. Check for colorfastness in an inconspicuous
place.
C. If possible, check upholstery stuffing.
Colored stuffing may bleed through fabric
when wet.
D. Planactivitiestoallowupholsterytimetodry.
E. Vacuum thoroughly to pick up loose debris
and pet hair. Use a vacuum with a brush
attachment and a crevice tool to clean in
fabric folds.
Manufacturer’s tag
13
w w w . b i s s e l l . c a
1 - 8 0 0 - 2 6 3 - 2 5 3 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Cleaning with attachments (continued)
WaRnInG:
To reduce the risk of
injury, be extra careful
when cleaning stairs.
Make sure machine is
secure and level.
2. Follow the instructions on pages 10 & 11 for filling the
2-in-1 water tank and the formula tank.
3. Set ReadyTools dial to the hose attachments setting.
This will allow spray and suction from the hose.
4. Set custom clean dial for heavy traffic, normal
clean, light clean, or water rinse as desired.
5. Attach the cleaning tool to the end of the hose.
6. Pluginandturnonthepowerswitchandheater(ifdesired).
5.
7. Clean by pressing the trigger to spray solution onto
the area to be cleaned. Slowly move the tool back
and forth over the soiled surface. Release the trigger
to suction soiled water. Continue to clean in the area,
working in small sections, until no more dirt can be
removed. Rinse (optional) and suction as needed.
Caution: Do no overwet.
9.
8. Remove and rinse tools in clean, running water.
10.
Dry and replace in the tool caddy.
9. It is recommended that you suction clean water
from a bowl to rinse out the hose.
10. Before replacing lift end of hose and stretch out to
ensure all water is cleared from hose.
11. Coil flex hose around the tool caddy.
12. Empty 2-in-1 water tank and rinse out,
following the instructions on page 12.
13. Return ReadyTools dial to floor setting.
w w w . b i s s e l l . c a
1 - 8 0 0 - 2 6 3 - 2 5 3 5
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Stain removal
Do not Delay! attending to an accident soon after
it occurs ensures the most optimal clean. Leaving
it for an extended period of time may cause it to
set and become permanent.
1. Blot up liquids with an absorbent cloth or paper
towels. White materials are recommended because
certain dyes may bleed and make the stain worse.
2. Gently scrape up any semi-solids with a spoon or
spatula.Do not use a knife or other utensil with sharp
edges because it could damage the carpet or upholstery.
3. If the area has dried, remove the remaining
semi-solids and residue with a sweeper or vacuum.
4. Be sure to test any spot removal formulas in an
inconspicuous area first. This is important as some
dyes and materials could be damaged or discolored
by cleaning solvents. If such a change should occur,
try a different solution or call a professional.
5. If cleaning on Berber carpeting, gently run your
machine over a hidden area. If no fuzzing occurs,
continue cleaning in soiled area.
6
CleanShot. CleanShot is an optional feature that
can be used to fight tough stains. It can be used as
either a tough stain pre-treat (see page 10) or can
be used during the deep cleaning process itself. To
use CleanShot either as a pre-treat or during deep
cleaning, follow the instructions below.
a. Set Custom Clean for the desired setting.
B. Press the CleanShot button and aim the
focused stream onto the stain. Allow the for-
mula to soak in for 30 seconds.
C. Run the machine over the stain to extract.
Repeat as needed until the stain is gone.
D. Rinse if desired.
7. Clean using either the FLOOR CLEanInG, or
TOOLS setting on the ReadyTools dial.
15
w w w . b i s s e l l . c a
1 - 8 0 0 - 2 6 3 - 2 5 3 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Hard floor cleaning
Your ProHeat 2X model may have come with a
hard floor attachment and Hard Floor Solutions
Formula. If not, these products are available for
purchase by contacting the BISSELL Consumer
Services department by phone or at the website.
The hard floor tool provides effective cleaning for
linoleum, vinyl, and tile floors.
WaRnInG:
To reduce the risk of fire and electric
shock- when cleaning a hard floor,
the BISSELL hard floor tool 203-
5642 must be used and it must only
be used with BISSELL Hard Floor
Solutions or BISSELL 2X Hard Floor
Solutions cleaning fluid intended for
use with this appliance.
Caution: Do not use on unsealed hardwood floors.
1. Vacuum or sweep thoroughly to pick up any
loose debris and pet hair.
2. Move any furniture, if needed.
3. Fill with water to "WATER" line. Fill
with BISSELL 2X Hard Floor Solutions to
"FORMULA" line.
4. Fill the 2-in-1 water tank with hot tap water
and set aside.
5. Attach the hard floor tool onto the bottom of
the machine by hooking it into the nozzle and
swinging it down until it clicks into place.
5.
6. Check ReadyTools dial. It should be set on
floor cleaning.
7. Set the Custom Clean dial to normal clean.
8. Plug into an outlet and turn the power
switch and heater On ( I ).
9. Slowly move the machine forward and back over
hard floor surface one time while depressing
trigger. Caution: Do not overwet.
10. Repeat the motion without pressing the
trigger using the hard floor tool to squeegee
and suction up the dirty water.
11. Allow adequate time for floors to dry.
12. Removehardfloortool,rinseanddrybeforestoring.
13. If any formula remains in the formula tank,
pour it back into the Hard Floor Solutions
bottle for use the next time.
14. Rinse out the formula tank.
w w w . b i s s e l l . c a
1 - 8 0 0 - 2 6 3 - 2 5 3 5
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and care
Machine storage
Once your cleaning is complete, make sure
the 2-in-1 water tank is emptied, rinsed out,
and dried before the next use. The formula
tank can remain filled and ready to go.
note: Store cleaner in a protected, dry area.
Since this product uses water, it must not be
stored where there is a danger of freezing.
Freezing will damage internal components
and void the warranty.
Machine care
For best results, a few simple steps can assure
your machine is well maintained after your
cleaning is complete.
1. Turn power and heater switches OFF (O).
Unplug the machine and wrap the power cord.
WaRnInG:
To reduce the risk of fire,
electric shock or injury
unplug from outlet before
servicing.
2. After emptying the 2-in-1 water tank, rinse
it out at a faucet with running hot tap water,
taking care to clean underneath the heavy
duty bladder, and all around it.
3. The top half of the tank can be rinsed clean
through the nozzle area. Also, pop out the red
filter underneath the top half of the tank and
rinse that out. Replace before putting the top
and bottom halves of the tank together.
4. Before you place the cleaned 2-in-1 water tank
back onto the machine, simply unscrew the floor
nozzle using a Phillips head
crewdriver.This
can be rinsed out at the faucet.Then replace
back onto the machine by starting from the
bottom of the nozzle and hooking the tabs into
the holes on the bottom sides of the machine.
Secure into place with the screw.
3.
Filter
Tip:
Let all parts dry completely
before storing
17
w w w . b i s s e l l . c a
1 - 8 0 0 - 2 6 3 - 2 5 3 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and care
Machine care (continued)
5. The inside of the end caps by the brush rolls
can be wiped out with a clean paper towel,
or, if a more thorough cleaning is desired, the
end caps can be taken off using a Phillips
head
screwdriver and rinsed clean.
WaRnInG:
To reduce the risk of fire,
electric shock or injury,
unplug from the outlet
before servicing.
Replace after cleaning.
6. Any loose hair or debris can be pulled from the
brush rolls and thrown away. For the most
thorough clean before storage, follow directions
on pages 18 & 19 for removal and replacement
of the brush rolls and belts.
7. To clean attachments that may have been
used, remove from hose and rinse in clean,
running water. Dry and replace attach-
ment in the tool caddy. Clean the hose by
suctioning clean water from the tap. Before
replacing, lift end of hose and stretch out to
ensure all water is cleared from hose. Refer
to page 14, illustrations 9 & 10.
1.
3.
2.
8. After carpet is dry, vacuum again to remove
hair and fuzz.
Small belt removal and replacement
Occasional replacement of one or both belts
may become necessary. If that is needed, please
follow the instructions below.
4.
6.
8.
5.
7.
1. Turn off the machine, and unplug it from
the outlet.
2. Remove both the 2-in-1 water tank and the
formula tank. Set aside.
3. Unscrew the front nozzle and remove it.
Set aside.
4. Turn the machine on its side.
IMPORTanT: cord side down.
5. Remove the clear end cap by unscrewing
the 2 black screws. Take care not to drop
the screws into the unit.
2
1
6. Remove 1 silver screw from the pivot arm.
7. Remove pivot arm by gently lifting up.
8. Remove small brush belt.
9.
9. Replace small brush belt, and reverse
steps above.
w w w . b i s s e l l . c a
1 - 8 0 0 - 2 6 3 - 2 5 3 5
18
Download from Www.Somanuals.com. All Manuals Search And Download.
WaRnInG:
To reduce the risk of fire,
electric shock or injury,
unplug from the outlet
before servicing.
Maintenance and care
Brush removal and large belt replacement
Brushes can be removed for cleaning or
replacement as needed.
2.
3.
1. Follow small belt removal Instructions on
page 18.
2. Remove brush rolls by pulling them off of
the metal rods.
3. Place cleaned or new brush rolls back onto the
rods. Make sure one washer is on each end of
the rollers prior to sliding onto the rod. Be sure
to let the rod slide through the bushing to
insure proper fit.
4.
5.
4. Re-attach the long belt on the bottom to the
cogs of the small roller brushes.
5. Place small belt over back roller and
metal cog.
6.
8.
7.
6. Place pivot arm in place and screw in place
using the silver screw.
7. Re-attach clear end cap by tightening with
the (2) black screws.
8. Return front nozzle to front of unit, by
latching from underneath and then securing
with a screw.
If you have any questions or are having
trouble installing or replacing your belt(s) or
brushes, please call BISSELL Consumer
Services at 1-800-263-2535.
Troubleshooting
Built-in heater ready light does not illuminate
Possible Cause
Remedies
1. The heater switch is not turned On ( I ).
2. The power switch is not turned On ( I ).
1. Turn the heater switch On ( I ).
2. Both switches must be On ( I ) to
activate the heater ready light.
Reduce Spray or no Spray
Possible Cause
Remedies
1. Water tank may be empty.
2. Formula tank may be empty.
1. Fill heavy duty bladder with hot tap water.
2. Fill formula tank with BISSELL Multi-
Allergen Formula for cleaning.
19
w w w . b i s s e l l . c a
1 - 8 0 0 - 2 6 3 - 2 5 3 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Reduce Spray or no Spray (continued)
Possible Cause
Remedies
3. Tank may not be seated completely.
3. Turn power OFF ( O ). Remove and
reseat tank.
4. Pump may have lost prime.
4. Turn power OFF ( O ) and then back
On ( I ). Wait one minute, then
depress Trigger.
DirtLifter PowerBrushes do not turn
Possible Cause
Remedies
1. The belt is off or broken.
1. Turn power OFF ( O ) and unplug unit
from outlet. Follow instructions on
page 18.
2. The unit is in the upright position.
2. Brushes only rotate when unit is
reclined using the detent pedal.
3.
3. Turn the machine OFF ( O ) and
unplug from outlet. Check to see if
foreign object is caught in brush roll.
Remove object. Plug machine back in
to reset circuit breaker.
Circuit breaker may have tripped.
Cleaner not picking up solution
Possible Causes
Remedies
1. ReadyTools dial may be at wrong setting.
1. Set ReadyTools dial to either FLOOR
CLEANING or TOOLS setting.
2. Tank may not be seated properly.
2. Pick up both the 2-in-1 water
tank and formula tank and reseat
them so they fit snugly on the unit.
3. Tank may not be assembled properly.
3. Check to make sure the "lip" of
the nozzle is securely hooked
into the groove on bottom of
Tank (see page 10).
4. Solution or 2-in-1 water tank is empty.
4. Check fluid levels in heavy duty
bladder and formula tank.
5. 2-in-1 water tank has picked up
maximum dirty water and red float
door has closed.
5. Empty 2-in-1 water tank. Refill
heavy duty bladder with clean
hot tap water and replace.
6. Red float "door" in the tank may have closed
as a result of bumping an object or moving
machine back and forth too quickly.
6. Turn the machine OFF ( O ),
allowing red float door to release into
the open position.Turn unit back
On ( I ) to continue cleaning. Be
sure your forward and backward
strokes are done at a slower pace.
w w w . b i s s e l l . c a
1 - 8 0 0 - 2 6 3 - 2 5 3 5
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Other maintenance or service not included in the manual should be performed by an
authorized service representative.
Thank you for selecting a BISSELL product.
Please do not return this product to the store.
For any questions or concerns, BISSELL is happy to be of service.
Contact us directly at 1-800-263-2535.
BISSELL Consumer Services
for information about repairs or replacement parts, or questions about your warranty, call:
BISSELL Consumer Services
1-800-263-2535
monday - friday
Saturday
or write:
8 a.m. — 10 p.m. ET
9 a.m. — 8 p.m. ET
BISSELL Canada Corporation
Box 1003
Niagara Falls, ON L2E 6W2
ATTN: Consumer Services
When contacting BISSELL, have model number of unit available.
Please record your model number: ___________________
Please record your Purchase Date: ___________________
nOTE: Please keep your original sales receipt. It provides proof of date of purchase in the event
of a warranty claim. See Warranty on page 24 for details.
21
w w w . b i s s e l l . c a
1 - 8 0 0 - 2 6 3 - 2 5 3 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacement parts - BISSELL ProHeat 2X (Continued)
Item Part no.
Part name
1
2
203-6611
203-6660
203-6618
203-6675
203-6676
203-6677
203-6678
203-6679
203-6845
203-6680
Grey Tank Assembly (complete)
Grey Tank Lid
Grey Tank Bottom
3
4
5
6
7
8
9
10
Cap and Insert for Water Tank
formula Tank (includes Cap & Insert for formula Tank)
Cap and Insert for formula Tank
front nozzle (includes gasket)
Autoload Gasket (fits both Water and formula Tank)
float Door
Tank filter (Lint Screen)
11
203-6681
Water Tank Latch
12
13
14
15
16
17
18
19
203-6682
203-6685
203-6686
203-6688
203-6804
203-6689
203-6690
203-6994
Cord Wrap (Black) (Blue or Purple cord wrap available upon request)
Clear End Cap w/Edge Brushes (2 pack, includes screws)
Brush Roll – 6 row (includes 1 brush, axle, 2 swivel arms)
Small Brush Belt (non-cord side)
Large Brush Belt (cord side)
Hose Secure Latch
Hose Rack Assembly (Top/Bottom Hose Rack, Screws)
CleanShot Cover
*not all parts are included with every model.
5
6
1
7
2
3
9
4
8
11
10
12
19
16
13
14
15
17
18
w w w . b i s s e l l . c a
1 - 8 0 0 - 2 6 3 - 2 5 3 5
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Replacement Parts*
Below please find a list of common replacement parts. While not all of these parts may have
come with your specific machine, all are available to you for purchase, if desired.
Item Part no.
Part name
1
2
203-6651
203-6652
203-6653
203-6654
203-6655
203-5642
62E5 C/D
99K5 C
3” Tough Stain Tool
Powered TurboBrush Hand Tool
4” Upholstery Tool
6” Stair Tool
Spraying Crevice Tool
Bare floor Tool, with trial size bottle of Hard floor Solutions™ formula
2X fiber Cleansing formula with Scotchgard™ Protection
2X Pet Stain and odor Removal formula with Scotchgard™ Protection
2X multi-Allergen Removal formula with Scotchgard™ Protection
2X Professional Deep Cleaning formula with Scotchgard™
3
4
5
6
7
8
9
10
89Q5 C/D
14n3 C
11
12
81T7
2X Hard floor Solutions formula
400 D
Tough Stain Precleaner
1
6
2
7
3
4
5
9
12
8
10
11
23
w w w . b i s s e l l . c a
1 - 8 0 0 - 2 6 3 - 2 5 3 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty - BISSELL ProHeat 2X Healthy Home
If you need additional instruction regarding this warranty or have questions regarding what it may cover, please
contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below.
Limited OnE Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product, BISSELL Canada
Corporation will repair or replace (with new or remanufactured components or products), at BISSELL’s option, free
of charge from the date of purchase by the original purchaser, for one year any defective or malfunctioning part.
See information below on “If your BISSELL product should require service”.
This warranty applies to product used for personal, and not commercial or rental service. This warranty does not
apply to routine maintenance components such as belts or brushes. Damage or malfunction caused by negligence,
abuse, or use not in accordance with the User’s Guide is not covered.
If your BISSELL product should require service
Call BISSELL Consumer Services at the number listed below or visit the BISSELL website – www.bissell.ca to
locate a BISSELL Authorized Service Centre in your area. If there are no authorized BISSELL Service Centres in
you a Return Authorization number and a pre-paid mailing label to return the unit to BISSELL for warranty repair.
The machine should be returned with a photocopy of your proof of purchase. (your dated sales receipt is your
warranty – do not send original.) If you need information about repairs or replacement parts, or if you have questions
about your warranty, contact BISSELL Consumer Services.
Website:
E-mail:
Or Call:
BISSELL Consumer Services
1-800-263-2535
monday – friday 8 a.m. – 10 p.m. ET
Saturday
9 a.m. – 8 p.m. ET
Or write:
BISSELL Canada Corporation
Box 1003,
niagara falls, on L2E 6W2
ATTn: Consumer Services
BISSELL CanaDa CORPORaTIOn IS nOT LIaBLE FOR InCIDEnTaL OR COnSEQUEnTIaL DaMaGES OF anY
naTURE aSSOCIaTED WITH THE USE OF THIS PRODUCT. BISSELL’S LIaBILITY WILL nOT EXCEED THE
PURCHaSE PRICE OF THE PRODUCT.
*EXCEPTIOnS anD EXCLUSIOnS FROM THE TERMS OF THE LIMITED WaRRanTY
THIS WARRAnTy IS EXCLUSIVE AnD In LIEU of Any oTHER WARRAnTIES EITHER
oRAL oR WRITTEn. Any ImPLIED WARRAnTIES WHICH mAy ARISE By oPERATIon
of LAW, InCLUDInG THE ImPLIED WARRAnTIES of mERCHAnTABILITy AnD
fITnESS foR A PARTICULAR PURPoSE, ARE LImITED To THE onE yEAR DURATIon
fRom THE DATE of PURCHASE AS DESCRIBED ABoVE.
nOTE: Please keep your original sales receipt,
it is your warranty.
©2010 BISSELL Homecare, Inc
BISSELL Canada Corporation
niagara falls, on L2E 6S5
All rights reserved. Printed in China
Part number 120-4168
Rev 01/10
Visit our website at:
Scotchgard is a trademark of 3m
w w w . b i s s e l l . c a
1 - 8 0 0 - 2 6 3 - 2 5 3 5
24
Download from Www.Somanuals.com. All Manuals Search And Download.
|