TM
PowerForce
U S E R ’ S G U I D E
3525/3530/3537/46E5/71Y7 SERIES
Safety Instructions
Product View
Assembly
3
4
5
6-9
7-10
10-11
11
Operations
Maintenance and Care
Troubleshooting
Replacement Parts
Consumer Services
Warranty
12
12
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic
precautions should be observed, including the
following:
■ ꢀKeep hair, loose clothing, fingers, and all parts of
body away from openings and moving parts.
■ ꢀTurn off all controls before plugging or unplugging
vacuum cleaner.
READ All InSTRUCTIOnS
bEfORE USInG YOUR
UPRIGhT VACUUM.
■ ꢀUse extra care when cleaning stairs.
■ ꢀDo not pick up flammable materials (lighter fluid,
gasoline, kerosene, etc.) or use in the presence of
explosive liquids or vapors.
Always connect to a polarized outlet (left slot is wider
than right). Unplug from outlet when not in use and
before conducting maintenance.
■ ꢀDo not pick up toxic material (chlorine bleach,
ammonia, drain cleaner, etc.).
■ ꢀDo not use vacuum cleaner in an enclosed space
filled with vapors given off by oil base paint, paint
thinner, some moth proofing substances, flammable
dust, or other explosive or toxic vapors.
WARnInG:To reduce the
risk of fire, electric shock,
or injury:
■ ꢀDo not pick up hard or sharp objects such as glass,
nails, screws, coins, etc.
■ Do not modify the polarized plug to fit a
non-polarized outlet or extension cord.
■ ꢀDo not pick up anything that is burning or smoking,
such as cigarettes, matches, or hot ashes.
■ Do not leave vacuum cleaner unattended when it is
plugged in.
■ ꢀDo not use without filters in place.
■ ꢀUse only on dry, indoor surfaces.
■ ꢀKeep appliance on a level surface.
■ Unplug from outlet when not in use and
before servicing.
■ Do not use outdoors or on wet surfaces.
■ ꢀDo not carry the vacuum cleaner while it
is running.
■ Do not allow children to operate vacuum
cleaner or use as a toy.
■ Close attention is necessary when used by or
near children.
SAVE ThESE
■ Do not use for any purpose other than described in
this User’s Guide.
InSTRUCTIOnS fOR
fUTURE USE.
■ Use only manufacturer’s recommended
attachments.
■ Do not use with damaged cord or plug.
■ If appliance is not working as it should,
has been dropped, damaged, left outdoors,
or dropped into water, have it repaired at an
authorized service center.
ThIS APPlIAnCE hAS
A POlARIZED PlUG.
■ Do not pull or carry by cord, use cord as a
handle, close a door on cord, or pull cord around
sharp edges or corners. Do not run appliance over
cord. Keep cord away from heated surfaces.
To reduce the risk of electric shock, this appliance has a
polarized plug (one blade is wider than the other). This plug
will fit in a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician to install a proper outlet.
Do not change the plug in any way.
■ ꢀDo not unplug by pulling on cord. To unplug, grasp
the plug, not the cord.
■ ꢀDo not handle vacuum cleaner or plug with
wet hands.
This model is for household use only.
■ ꢀDo not put any object into openings. Do not use
with any opening blocked; keep openings free of
dust, lint, hair, and anything that may reduce
air flow.
3
w w w . b i s s e l l . c a
1 8 0 0 2 6 3 - 2 5 3 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Product view
Handle
Cord Clip
Hose Clip
Hose
Bag Door
Carrying
Handle
Power Switch
Quick Release™
Cord Wrap
Crevice Tool
Quick ReachTM
Handle
Extension
Wand
Twist ‘n Snap™
Hose
Combination
Upholstery/Dusting
Brush Tool
Washable
Post-Motor
Filter
Tool Storage
Clips
Power Cord
Hose Wand
Handle
Release
Pedal
Suction Intake
Opening
Height Adjustment
Knob
Powerfoot
Furniture Protection
Guard
CAUTIOn:
Do not plug in your vacuum
cleaner until you are familiar
with all instructions and
operating procedures.
Made from 100% post consumer recycled content
w w w . b i s s e l l . c a
1 8 0 0 2 6 3 - 2 5 3 5
4
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use this guide
This User’s Guide has been designed to help you
get the utmost satisfaction from your bISSEll
Powerforce. You’ll find assembly and operating
instructions, safety precautions, as well as
maintenance and troubleshooting instructions.
Please read this Guide thoroughly before
assembling your vacuum cleaner.
Pay particular attention to the product diagram,
assembly instructions, and part names. locate
and organize all parts before assembly. following
this User’s Guide will greatly enhance your ability
to get the most performance from your bISSEll
Powerforce for many years.
WARnInG:
Plastic film can be
dangerous. To avoid
danger of suffocation,
keep away from babies
and children.
3.
1.
Assembly
The only tool you’ll need to assemble your
vacuum cleaner is a Phillips screwdriver.
Attach handle to vacuum
1. Stand the vacuum upright and slide the base
of the handle firmly into the grooves at the top
of the vacuum body.
2. Check to be sure the handle is fitted to the
vacuum body. If there is a gap in front, continue
to push firmly until the handle is flush.
1.
Hose
Collar
3. Insert one screw from the assembly packet
into the existing hole in the back of the
handle. Tighten securely with a screwdriver.
Attach vacuum hose and tools
1. Position the hose collar on the back of the
vacuum as shown.
3.
2. Attach the hose collar with two screws from
the assembly packet. Tighten securely with
a screwdriver.
4.
3. Line up the tabs on the base of the Twist ‘n Snap
Hose with the corresponding tab notches on the
hose collar as shown.Turn the Twist ‘n Snap Hose
to the left to lock the hose into place.
4. Grasping the Quick ReachTM Handle, slide the
end of the hose wand onto the suction intake
opening. Snap the hose into the hose clip.
5.
6.
nOTE: The powerfoot will not operate
effectively unless the hose wand is firmly
attached to the suction intake opening.
5. Place the crevice tool inside the extension wand
and slide them into the storage clip as shown.
6. Snap the combination upholstery/dusting brush
tool into the storage clip as shown.
5
w w w . b i s s e l l . c a
1 8 0 0 2 6 3 - 2 5 3 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Handle position
Press the handle release pedal with your foot to
place your bISSEll Powerforce into one of three
cleaning positions.
Tip:
Before cleaning under low furniture,
check area first for objects that might
harm the unit or block the vacuum hose.
1. Upright- For storage and above floor
cleaning with special tools.
1.
2.
2. normal Cleaning- Press handle release
pedal once. Use for most household floor
cleaning tasks.
3.
3. low Cleaning- With the vacuum in normal
cleaning position press handle release pedal
again. Use for reaching under low furniture
such as tables, chairs and beds.
Powerfoot height adjustment
The powerfoot/rotating floor brush on your bISSEll
Powerforce can be adjusted to clean several
floor surfaces.
nOTE: for optimal cleaning performance,
adjust to the lowest practical setting. If
your cleaner is difficult to push, adjust to
the next higher setting.
1. Place handle in upright position.
CAUTIOn:
The rotating floor brush continues to
rotate while tools are in use. To reduce
the risk of injury from moving parts,
always move the vacuum cleaner
with the carrying handle at the back
of the cleaner. Always place vacuum
cleaner on floor with handle in upright
position when using tools. never place
your fingers under the vacuum cleaner
when it is running. never place
2. Turn height adjustment knob to desired setting.
lowest Setting - For bare floors.
Medium Settings - For short and medium
pile carpets.
highest Setting - For plush pile or Berber
carpet.
3. Place the handle into the normal cleaning
position and the powerfoot will adjust to the
setting chosen.
powerfoot on furniture or uneven
surfaces. Do not place vacuum cleaner
close enough to objects to pull them
into rotating brush.
nOTE: You may also adjust the setting while
in the normal cleaning position.
Special tools
Your bISSEll Powerforce is not only a powerful
carpet and rug vacuum cleaner, it’s also a
versatile above floor vacuum cleaner when you
select one of the special tools.
Tip:
Hair, string and small
objects can block
the vacuum hose or
tools. Check them
occasionally for
1. Raise handle to upright position.
2. Grasp the quick reach handle and lift up to
separate from suction intake opening.
obstructions. See
Troubleshooting
Guide for instructions.
3. Attach tools by firmly pushing onto hose
wand or extension wand.
w w w . b i s s e l l . c a
1 8 0 0 2 6 3 - 2 5 3 5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Special tools
Combination upholstery/dusting brush tool:
Two types of cleaning tools are included in one
attachment: rotate for desired tool.
■ꢀ Use brush side to dust furniture, blinds,
books, lamps, shelves.
■ꢀ Use upholstery side for curtains,
draperies, cushions, fabrics.
Crevice Tool:
Use in tight narrow spaces.
Tip:
Extension Wand: Use with desired attachments for
a longer reach.
Your BISSELL PowerForce features
nOTE: When using the hose for above floor
cleaning, make sure the powerfoot does not
tilt forward.
™
a Quick Release Cord Wrap. To
remove the power cord quickly and
easily, rotate the upper cord wrap
toward floor, and slip power cord from
upper and lower cord wrap.
Power cord
When you are done using your bISSEll
Powerforce, return it to the upright position and
store the power cord.
1. Turn vacuum cleaner OFF.
WARnInG:
To reduce the risk of electric
shock, turn power switch Off
and disconnect polarized plug
from electrical outlet before
performing maintenance or
troubleshooting checks.
2. Unplug power cord by grasping the polarized
plug (NOT the cord) and disconnect from outlet.
3. Loop power cord around cord wraps on side
of vacuum cleaner.
4. Clip molded plug to power cord to secure.
Maintenance and care
To maintain maximum performance from your
bISSEll Powerforce, perform these simple
maintenance checks.
Tip:
Vacuuming new carpet or fine powders
may clog the dust bag causing the
bag change indicator to turn red even
though the dust bag does not appear
to be full. Change the dust bag to
restore maximum performance.
Bag change indicator (select models)
Select bISSEll Powerforce models are equipped
with a bag change indicator.This indicator monitors
the airflow through the dust bag and turns red to
indicate a reduction or blockage.The following
conditions may cause it to become completely red.
1. Dust bag is full; change the bag.
2. Dust bag is clogged with fine materials;
change the bag.
3. Clog in the vacuum; clear the clog.
Bag Change
Indicator
7
w w w . b i s s e l l . c a
1 8 0 0 2 6 3 - 2 5 3 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and care
Replace dust bag
4.
never reuse a dust bag.
Use only bISSEll Style 7 Dust bags in your bISSEll Powerforce.
Style 7 Envirofresh Micro filtration Dust bags (# 30861)
Style 7 Dust bags (# 32120).
1. Unplug cleaner from electrical outlet.
2. Pull the bag door outward to open. Set bag door aside.
5.
3. Grasp dust bag collar, and pull collar from connector
tube. Discard used dust bag.
4. Grasp new dust bag collar and push firmly onto
connector tube. Tuck in dust bag.
5. Replace bag door by placing tab on bottom of door into opening as
shown.Press top of door to snap securely shut.
nOTE: Vacuum will not suction while the bag
door is removed.
Pre-Motor
Cleaning pre-motor & post-motor filters
Filter
Use only bISSEll Replacement filters in your
bISSEll Powerforce.
1. Unplug cleaner from electrical outlet.
Post-Motor
Filter
2. The pre-motor filter, located in the bottom of the bag
compartment, protects the motor from dirt particles. If
filter becomes dirty, lift out filter and clean.
WARnInG:
Do not operate cleaner
3. The post-motor filter assists in the filtration process to
return clean air to the room.To remove this filter, open
the door on the side of the cleaner. Grasp filter and pull
it straight out.
with damp or wet filters or
without all filters in place.
4. The filters may be hand washed in cold water with
WARnInG:
To reduce the risk of
injury from moving parts,
turn off vacuum cleaner
and disconnect Power
Plug from
mild detergent, then air dried.
5. Reposition filters when completely dry.
Check rotating floor brush and drive belt
You should check your vacuum cleaner’s rotating floor
brush and drive belt regularly for wear or damage. You
electrical outlet.
should also clean the brush and brush ends of string, hair, and carpet
fibers. These can wrap around the brush and hamper its ability to
effectively clean your carpet. Also remove any debris that has
accumulated under the brush cover.
1. Unplug cleaner from electrical outlet.
2. Place handle in low position and turn vacuum cleaner over so
bottom side is up.
3. Remove the four screws as shown with a Phillips head
Brush
Cover
screwdriver. Lift the brush cover off.
4. Grasp rotating floor brush at both ends and lift.
w w w . b i s s e l l . c a
1 8 0 0 2 6 3 - 2 5 3 5
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and care
Check rotating floor brush and drive belt (continued)
Air Passageway
5. Clean strings, hair and other debris from
Motor Pulley
rotating floor brush, paying particular
attention to brush ends.
6. Clean strings, hair and other debris from motor
pulley and drive belt areas.
7. Check drive belt carefully for wear, cuts or
stressed areas. Replace if worn.
8. Check air passageway for obstructions.
Remove debris from this area.
Replace drive belt
Use only bISSEll Style 7 Replacement belts
(#32074) in your bISSEll Powerforce.
1. Unplug cleaner from electrical outlet.
2. With rotating floor brush removed from vacuum
cleaner (Steps 1-4 of Check rotating floor brush
and drive belt), grasp old drive belt and remove
from motor pulley. Discard old drive belt.
3. Place new drive belt over motor pulley and
stretch other end over rotating floor brush in
the space between the bristles.
Press here
4. Place ends of rotating floor brush down into
slots on sides as shown.
5. Turn rotating floor brush by hand several
times in direction of motor pulley. If properly
installed, drive belt will center itself.
Brush
Cover
6. Reposition brush cover and four screws.
Tighten screws securely. Make sure end of
brush cover is snapped into place.
Replace light bulb (select models)
Select models are equipped with a headlight.
Use only bISSEll Replacement bulbs in your
bISSEll Powerforce.
1. Unplug cleaner from electrical outlet.
2. Insert a flat screwdriver or coin into the
slot on the right of the lens and gently push
inner latch to the left as shown to remove
the lens.
3. Remove the bulb from the socket by grasping
bulb and pulling straight out. Install the new bulb
by pushing it gently into the socket until the bulb
snaps into place
4. Reposition lens, by inserting tab on left
side and then pushing the right side back
into place.
9
w w w . b i s s e l l . c a
1 8 0 0 2 6 3 - 2 5 3 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and care
Clearing clog
Suction Inlet
The hose on the back of the vacuum cleaner
that carries the dirt from the powerfoot to the
dust bag can sometimes become clogged. If
you notice a change in the sound of the vacuum
motor, check for clogs.
1. Unplug cleaner from electrical outlet.
2. Pull the bag door outward to open and set
aside. Remove the dust bag to check the
suction Inlet for a clog.
3. Grasp the quick reach handle and lift up to
separate from the suction intake opening.
Check for a clog in the base, the wand or the
hose.
Air Passageway
4. Release the hose from the vacuum by
turning to the right. Straighten the hose and
unclog with a long, narrow object.
5. If the clog persists, turn the vacuum cleaner
OFF and unplug it. Remove the brush cover.
Check the air passageway for obstructions.
Remove debris from this area. Reposition
brush cover and four screws. Tighten screws
securely. Make sure end of brush cover is
snapped into place.
WARnInG:
To reduce the risk of
electric shock, turn power
Off and disconnect
polarized plug from
electrical outlet before
performing maintenance
or troubleshooting.
Troubleshooting
Vacuum cleaner won’t turn
Possible causes
Remedies
1. Power cord not firmly plugged in
1. Check electrical plug
2. Blown fuse/tripped breaker
2. Check/replace fuse or reset breaker.
Vacuum cleaner won't pick up dirt
Possible causes
Remedies
1. Incorrect height adjustment
2. Hose not attached to suction opening
1. Adjust powerfoot to correct height setting
2. Grasp hose grip and firmly push onto the base
3. Make sure Twist 'n Snap hose is snapped
3. Twist 'n Snap hose not securely attached
into position
4. Dust bag is full
4. Replace with new dust bag
5. Replace brush
5. Rotating floor brush bristles worn
6. Remove brush and clean debris from
6. Rotating floor brush jammed
7. Clog in vacuum
brush ends
7. Follow instructions for clearing clogs
w w w . b i s s e l l . c a
1 8 0 0 2 6 3 - 2 5 3 5
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Tools won't pick up dirt
Possible causes
Remedies
1. Crack or hole in hose
1. Replace hose
2. Vacuum hose, wand or tools clogged
2. Follow instructions for cleaning clogs
Vacuum cleaner difficult to push
Possible causes
Remedies
1. Turn floor surface selector to next
1. Incorrect height adjustment
highest setting
2. Rotating floor brush not rotating
2. Check drive belt and brush
Other maintenance or service not included in the manual should be performed by an
authorized service representative.
Thank you for selecting a bISSEll product.
If you should happen to need assistance during assembly or operation, call 1 800 263-2535.
Please do not return this product to the store.
for any questions or concerns, bISSEll is happy to be of service.
Contact us directly at 1 800 263-2535.
Replacement Parts - BISSELL PowerForce
Replacement parts are available through bISSEll Consumer Services, an authorized bISSEll
Service Centre or by visiting our website. below is a list of common replacement parts. While
not all of these parts may have come with your specific model, they are available for purchase
if desired.
1/2
3
4
Item Part no.
Part name
Style 7 EnviroFresh Micro
Filtration Dust Bag (3-Pack)
1
30861
2
3
4
5
6
32120
32074
203-1297
203-1056
203-1059
Style 7 Dust Bags (3-Pack)
Style 7 Drive Belt (2-Pack)
Light Bulb (select models only)
Crevice Tool
Combination
Upholstery / Dusting Brush
5
6
7
7
8
9
10
11
12
203-1068
203-1127
203-1129
203-5624
203-5576
203-1009
Extension Wand
Twist n' Snap Vacuum
Hose Collar
Brush Roll
Pre-Motor Filter
Style 7 Post-Motor Filter
8
10
9
Hose
11
12
11
w w w . b i s s e l l . c a
1 8 0 0 2 6 3 - 2 5 3 5
Download from Www.Somanuals.com. All Manuals Search And Download.
BISSELL Consumer Services
For information about repairs or replacement parts, or questions about your warranty, call or write:
bISSEll Consumer Services
1-800-263-2535
Monday - Friday 8 a.m. — 10 p.m. ET
BISSELL Canada Corporation
Saturday
9 a.m. — 8 p.m. ET
Box 1003
Or visit the BISSELL website
Niagara Falls, ON L2E 6W2
ATTN: Consumer Services
When contacting BISSELL, have model number of unit available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
nOTE: Please keep your original sales receipt. It is your warranty.
Warranty
If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL
Consumer Services by E-mail, telephone, or regular mail as described below.
limited One Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL Canada
Corporation will repair or replace (with new or remanufactured components or products), at BISSELL’s option, free of
charge from the date of purchase by the original purchaser, for one year any defective or malfunctioning part.
See information below on "If your BISSELL product should require service".
This warranty applies to product used for personal,and not commercial or rental service.This warranty does not apply to fans or routine
maintenance components such as filters,belts,or brushes.Damage or malfunction caused by negligence,abuse,neglect,unauthorized
repair, or any other use not in accordance with the User's Guide is not covered.
If your bISSEll product should require service:
Call BISSELL Consumer Services at the number listed below or visit the BISSELL website – www.bissell.ca to locate a
BISSELL Authorized Service Centre in your area. If there are no authorized BISSELL Service Centres in your area, a BISSELL
Representative at [email protected] or at the phone number below will issue you a Return Authorization Number
and a pre-paid mailing label to return the unit to BISSELL for warranty repair.
The machine should be returned with a photocopy of your proof of purchase. (Your dated sales receipt is your warranty – do
not send original.) If you need information about repairs or replacement parts, or if you have questions about your warranty,
contact BISSELL Consumer Services.
Website or E-mail:
Use the “Customer Services” tab.
Or Call:
BISSELL Consumer Services
1-800-263-2535
Or write:
BISSELL Canada Corporation
Box 1003
Monday - Friday 8 a.m. - 10 p.m. ET
Saturday 9 a.m. - 8 p.m. ET
Niagara Falls, ON L2E 6W2
ATTN: Consumer Services
BISSELL CANADA CORPORATION IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH
THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE
PRODUCT.
*EXCEPTIOnS AnD EXClUSIOnS fROM ThE TERMS Of ThE lIMITED WARRAnTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR
WRITTEN.ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,ARE
LIMITED TO THE ONE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
©2008 BISSELL Homecare, Inc
BISSELL Canada Corporation
Niagara Falls, ON L2E 6W2
All rights reserved. Printed in China
Part Number 110-4090
Rev 11/08
nOTE: Please keep your original sales receipt, it is your warranty.
Visit our website at:
w w w . b i s s e l l . c a
1 8 0 0 2 6 3 - 2 5 3 5
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|