Bertazzoni Range M7S0GTU4X2 OR 5A User Manual

Installation, Service and User Instructions

FREESTANDING GAS RANGES

BERTAZZONI

DIMENSIONS: 30’’ (762 mm)(W) x 253/16’’ (640 mm)(D) x36’’ (915 mm)(H)

Models X304GGVX [M7S0GTU4X(2 or 5)A]

IMPORTANT - PLEASE READ AND FOLLOW

-Before beginning installation, please read these instructions completely and carefully.

-Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty. -Please observe all local

and national codes and ordinances.

-Please ensure that this product is properly grounded.

-The installer should leave these instructions with the consumer who should retain for local inspector's use and for

future reference.

-The electrical plug should always be accessible.

Installation must conform with local codes or in the absence of codes, the National Fuel Gas Code ANSIZ223.1-latest edition. Electrical

^{installation must be in accordance with the National Electrical Code, ANIS/NFPA70}- latest edition and/or local codes. IN CANADA:

Installation must be in accordance with the current CAN/CGA-B149.1 National Gas Installation Code or CAN/CGA-B 149.2, Propane

Installation Code and/or local codes. Electrical installation must be in accordance with the current CSA C22.1 Canadian Electrical

Codes Part 1 and/or local codes.

Installation of any gas-fired equipment should be made by a licensed plumber. A manual gas shut-off valve must be installed in the gas

supply line ahead of the oven in the gas flow for safety and ease of service.

In Massachusetts: All gas products must be installed by a "Massachusetts" licensed plumber or gasfitter. A "T" handle type manual

gas valve must be installed in the gas supply line to this appliance.

Warning!

- This range can tip. Injury to persons could result.

- Install anti-tip device shipped with range.

-See Installation Instructions

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR’S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

OBSERVE ALL GOVERNING CODES AND ORDINANCES.

WARNING: If the information in this manual is not followed exactly, a

fire or explosion may result causing property damage, personal injury

or death.

Do not store or use gasoline or other flammable vapors and liquids in

the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

- Do not light any appliance.

- Do not touch any electrical switch.

- Do not use any phone in your building.

- Immediately call your gas supplier from a neighbor’s phone. Follow

the gas supplier’s instructions.

- If you cannot reach your gas suppliers, call the fire department.

Installation and service must be performed by a qualified installer,

service agency or the gas supplier.

310240

Download from Www.Somanuals.com. All Manuals Search And Download.

Requirements

Room ventilation – Location and venting.

ATTENTION: An exhaust fan may be used with the appliance; in each case it shall be installed in

conformity with the appropriate national and local standards.

ATTENTION: Exhaust hood operation may affect other vented appliances; in each case it shall be

installed in conformity with the appropriate national and local standards.

INSTALLATION MANUAL

ANTI-TIP STABILlTY DEVICE INSTALLATION INSTRUCTIONS

1. The anti-tip bracket have to be installed to the rear wall as shown. The height for the bracket location from

the floor has to be determined after the range legs have been adjusted to the proper installation height - as

shown in the installation instructions – and after the range has been leveled.

2. Measure from the floor to the bottom of the anti-tip bracket location on the back of the range.

3. Position the two anti-tip brackets on the wall at the measured dimension plus 1/8" (0.32 cm). The brackets

have to be placed at 2”5/16 (6,0 cm) from the side of the range. The distance between the two bracket is

31”1/4 (79,3 cm) clearance. Secure with suitable inserts.

4. Slide the range against the wall until the brackets are fully inserted into the holes on the backside of the

range..

Height adjustable legs:

1. Legs are packed in the top box.

2. Legs should be installed with the appliance being near the location of final installation, they are not secure

for long transport. After unpacking the range, raise it about a foot to insert the legs in their bases assembled

on the lower part of the cooker and lower the range gently to keep any undue strain from legs and mounting

hardware. It is recommended to use a pallet or lift jack instead of tilting the unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

BACKGUARD INSTALLATION INSTRUCTION

1) Remove n°2 screws fixing worktop as shown in fig.1

2) Place front part of the backguard and attach it from bottom side with the two removed screws (point 2) as shown in

fig .2

3) Fix the front part of the backguard with the screws supplied with the backguard kit (fig.3)

4) Assemble back part with front part of the backguard and fix them with a screws supplied with the backguard kit

(fig.4)

WORKTOP FRONTGUARD INSTALLATION INSTRUCTIONS

In order to increase the clearance between front edge of the worktop and the burners for your safety it is

recomended to install the worktop frontguard supplied with the appliance. For installation instructions follow

the instructions indicated in the following figures

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION SIDE-BY-SIDE TO KITCHEN CABINET

1. This range may be installed directly adjacent to existing 36" (91.5 cm) high cabinets. IMPORTANT: The

top border of the worktop should be at the same level of the adjacent cabinet countertop. This can be

accomplished by raising the unit using the adjustment spindles on the legs.

2. The range CANNOT be installed directly adjacent to sidewalls, tall cabinets, tall appliances, or other vertical surfaces

above 36" (91.4 cm) high. There must be a minimum of 6" (15.2 cm) side clearance.

3. Within the side clearance to combustible vertical surfaces above 36" (91.5 cm) , the maximum wall cabinet depth must

be 13" (33.0 cm) and wall cabinets within this side clearance must be 18" (45.7 cm) above countertop level and

countertop hightness shall be from 35”1/2(90,2 cm) to 37” ¼ (94,6 cm).

30” (76,2 cm)

36” (91,5 cm)

C 13” (33,0 cm)

D 18” (45,7 cm)

35”1/2(90,2 cm) / 37” ¼ (94,6 cm)

6” (15,2 cm)

Download from Www.Somanuals.com. All Manuals Search And Download.

COOKER HOOD INSTALLATION

The bottom of the hood should be 25 1/2" (65 cm) min. to 31 1/2" (80 cm) above the countertop. This would

typically result in the bottom of the hood being 61 1/2" (156.2 cm) to 67 1/2" (171.5 cm) above the floor. Check

for other minimum clearance requirements mandated by specific local or regional installation codes. Refer to

the rangehood installation instructions for additional information. These dimensions provide for safe and

efficient operation of the hood.

ELECTRICAL CONNECTION

This unit is manufactured for a polarized, grounded 120 VAC/60 Hz, 15A 3 pin-earthed receptacle. Electric

power consumption is about 150 W. The minimum of 102 VAC is required for proper operation of gas ignition

systems. This circuit must be grounded and properly polarized. The unit is equipped witth a SJT power cord.

In case of replacement, the cable shall be replaced with one of the same type, size and length.

WARNING

Cooling fan failure.

In case of a cooling fan failure the frontal red indicator "Fan Failure" will light up. If this happens, please turn

off the appliance immediately, call the nearest after sale assistance service center and do not use the

appliance until the cooling fan system of the appliance has been properly repaired by a qualified technician.

WARNING

Electrical Grounding Instructions

This appliance is equipped with a three-prong plug for your protection against shock hazard and should be

plugged directly into a properly grounded socket. Do not cut or remove the grounding prong from this plug.

WARNING

ELECTRICAL SHOCK HAZARD

•

Disconnect electrical power at the circuit breaker box or fuse box before installing the gas cooker

Electrically ground gas cooker

•

Use copper conductors only. Failure to follow these instructions could resul in serious injury or death

Download from Www.Somanuals.com. All Manuals Search And Download.

Wiring diagram

For freestanding gas range model X304GGVX M7S0GTU4X(2 or 5)A

CAUTION: label all wires prior to disconnection when servicing controls. Wiring errors can cause

improper and dangerous operation.

Verify proper operation after servicing.

GAS CONNECTION

All gas connections must be made according to national and local codes. The gas supply (service) line must be the same

size or greater than the inlet line of the appliance. This range uses a 1/2" NPT inlet (see fig. in this chapter for details of

gas connections installations).On all pipe joints use sealant resistant to LP gas.

1. Manual Shut-off Valve:

This installer-supplied valve must be installed in the gas service line ahead of the appliance in the gas flow and in a

position where it can be reached quickly in the event of an emergency. The manual shut-off valve shall be installed

properly in order to be accessible when the appliance is installed. In Massachusetts: A 'T' handle type manual gas

valve must be installed in the gas supply line to this appliance.

2. Pressure Regulator(see fig. in this chapter)

a) All cooking equipment must have a pressure regulator on the incoming service line for safe and efficient

operation, since service pressure may fluctuate with local demand. The pressure regulator is supplied

separately with the appliance; regulator has two female threads ½” NPT; it shall be installed properly in order

to be accessible when appliance is installed in final position.

b) Any conversion required must be performed by your dealer or a qualified licensed plumber or gas service

company. Please provide the service person with this manual before work is started on the range. (Gas

conversions are the responsibility of the dealer or end user.)

c) This range can be used with Natural or LP/Propane gas. It is shipped from the factory adjusted for use with

natural gas.

d) Manifold pressure should be checked with a manometer, natural gas requires 4.0" W.c.P. and LP/Propane

requires 11.0" W.C.P. Incoming line pressure upstream from the regulator must be 1" W.c.P. higher than the

manifold pressure in order to check the regulator. The regulator used on this range can withstand a

maximum input pressure of 1/2 PSI (14.0" W.c.P.) If the line pressure is in excess of that amount, a step-

down regulator will be required.

e) The appliance, its individuai shut-off valve, and pressure regulator must be disconnected from the gas

supply piping system during any pressure testing of that system at pressures in excess of 1/2 psig (3.45

kPa).

f) The appliance must be isolated from the gas supply piping system by closing its individuai manual shut-off

valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2

psig (3.45 kPa).

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Flexible Connections:

a) If the unit is to be installed with flexible couplings and/or quick disconnect fittings, the installer must use a

heavy-duty, AGA design-certified commerciai flexible connector of at least 1/2" (1.3 cm) ID NPT (with

suitable strain reliefs) in compliance with ANSI Z21.41 and Z21.69 standards.

b) In Massachusetts: The unit must be installed with a 36" (3-foot) long flexible gas connector.

c) In Canada: CAN 1-6.10-88 metal connectors for gas appliances and CAN 1-6.9 M79 quick disconnect

device for use with gas fuel.

CAUTlON: Leak testing of the appliance shall be conducted according to the manufacturer's instructions. Before placing

the oven into operation, always check for leaks with a soapy water solution or other acceptable method. DO NOT USE

AN OPEN FLAME TO CHECK FOR LEAKS!

2”( 5 cm)

3”(7,6 cm)

8”(20,3 cm)

A properly-grounded horizontally- mounted electrical receptacle should be installed no higher than 3" (7.6 cm) above the

floor, no less than 2”( 5 cm) and no more than 8”(20,3 cm) from the right side (facing product). Check all local code

requirements.

An agency-approved, properly-sized manual shut-off valve should be installed no higher than 3" (7.6 cm) above the floor

and no less than 2”( 5 cm) and no more than 8”(20,3 cm) from the left side (facing product). To connect gas between

shut-off valve and regulator, use agency-approved, properly sized flexible or rigid pipe. Check all local code

requirements.

PERFORMANCE CHECKLlST

All burners are tested before leaving the factory. There are no adjustments for the burners if connected according to the

information on the rating plate. Check each burner for proper operations. Flames should be blue in all settings. If service

is required, contact your dealer for the name of their authorized service agency. Gas conversions and initial installation

are not the responsibility of the manufacturer.

The installer should carry out the following performance checks. Refer to instructions below.

1. Check surface burner ignition.

2. Check air shutter adjustment (only for oven and broiler burner)- sharp blue flame, no yellow tipping, sooting or flame

lifting

3. Check low flame adjustment

4. Check broiler and oven ignition - all burner ports.

5. Check for gas leaks (odors) at all gas connections.

6. Check oven bake and convection bake function.

FINAL PREPARATION

1. Some stainless steel parts may have a plastic protective wrap which must be removed. The interior of the oven

should be washed thoroughly with hot soapy water to remove film residues and any installation dust or debris

before using it for food preparation, then rinsed and wiped dry. Solutions stronger than soap and water are rarely

needed.

2. All stainless steel body parts should be wiped with hot, soapy water and with a liquid cleaner recommended for

use with stainless steel If buildup occurs, do not use steel wool, abrasive cloths, cleaners, or powders! If it is

necessary to scrape stainless steel to remove encrusted materials, soak with hot, wet cloths to loosen the

material, then use a wood or nylon scraper. Do not use a metal knife, spatula, or any other metal tool to scrape

stainless steel! Scratches are almost impossible to remove.

NOTE: These installation instructions should remain with the unit for future reference. The electrical diagram is located in

the backside or the appliance.

Download from Www.Somanuals.com. All Manuals Search And Download.

REPLACEMENT PARTS

Only authorized replacement parts may be used in performing service on the appliance. Replacement parts are available

from factory authorized parts distributors.

Conversion to different types of gas

Before carrying out any maintenance work, disconnect the appliance from the gas and electric

supply. For Natural Gas fit regulator assembly described in Fig.

Adaptation of the pressure regulator for use with different type of gas

The pressure regulator supplied with the appliance is a convertible type pressure regulator for use with Natural Gas at a

nominal outlet pressure of 4” w.c. or LP gas at a nominal outlet pressure of 11” w.c. and it is pre-arranged from the

factory to operate with one of these gas/pressure as indicated in the labels affixed on the appliance, package and

Instruction booklet.

To convert the regulator for use with other types of gas follow these instructions:

1) Unscrew by hand the upper metal stopper of the regulator.

2) Unscrew by hand the white plastic piece screwed under the above mentioned metal stopper, afterward screw it again

in opposite way under the metal stopper (for gas reference see the written “LP” and “NAT” with relative indicating arrows

on the white piece).

3) Screw again by hand the metal stopper in the original position on the regulator.

Following these exact instructions the gas regulator is converted for use with the other gas/pressure.

It is essential that the gasket and the pressure test point stopper are properly installed to avoid gas leakage

- CHANGING THE NOZZLES FOR USE WITH OTHER TYPES OF GAS:

To change the nozzles of the burners use the following procedure:

Lift up the burners and unscrew the nozzles ( Fig.) using an adjustable spanner of 7 mm and change the nozzles with

those designed for the new gas supply according to the information given in TABLE shown below.

Follow the instructions below to change the oven burner nozzle:

1) Remove the oven door (Fig. 9A-9B)

2) Remove the lower frontal cavity gasket and the enamelled cavity base plate (Fig. 10)

3) Loosen and the screw V and pull out the burner from the support being careful not to damage the ignition plug and

the thermocouple (Fig. 11)

4) Unscrew the nozzle R (Fig. 11) using a 7 mm. spanner and replace it with the nozzle for the new type of gas

according to what is indicate in the table below

5) Re-install all the parts in revers sequence from 3 to 1

Download from Www.Somanuals.com. All Manuals Search And Download.

Fig. 9A

Fig. 9B

Fig. 10

Fig. 11

Follow the instructions below to change the broiler burner nozzle:

1) Loosen the screw and pull out the burner from the support being careful not to damage the ignition plug and the

thermocouple (Fig. 12).

2) Unscrew the nozzle C (Fig. 12) using a 7 mm spanner and replace it with the nozzle needed for the new type of gas

according to what is indicated in TABLE shown below.

Fig. 12

Download from Www.Somanuals.com. All Manuals Search And Download.

Models X304GGVX [M7S0GTU4X (2 or 5)A]

Adapting to different types of gas

CAUTION: save the orifices removed from the appliance for future use

Burner

Auxiliary

Semi-Rapid

Rapid

Position

Rear L

Injector

diam. [mm.]

0,90

Gas

Type

Pressure

[i.w.c.]

4”

Max Rate

[BTU/h] [W]

Min Rate

[BTU/h]

By-pass

diam. [mm]

Regulated

0,29

Regulated

0,36

Regulated

0,47

Regulated

0,29

Regulated

0,65

Regulated

0,54

No by-pass

[W]

264

3400

6100

996

1787

900

0,54

1,18

0,70

1,55

0,92

0,80

0,49

LP (Propane)

11”

4”

11”

4”

11”

4”

11”

4”

11”

4”

264

Front R

LP (Propane)

1500

2500

900

439

732

Rear R

10400 3047

LP (Propane)

Front L Inner

Front L Outer

LP (Propane)

2800

820

264

Dual Burner

900

264

N°2 x 1,15

N°2 x 0,70

1,85

12000 3516

14500 4248

12000 3516 Only Max Only Max

4500

3500

1318

1025

LP (Propane)

Oven

downside

Oven

LP (Propane)

1,10

1,70

0,98

11”

4”

11”

Broiler

upside

LP (Propane)

REGULATION OF BURNERS

Primary air adjustment:

Broiler burner adjustment: to adjust the broiler burner loosen screw P and adjust the position X of the Venturi cone

according to the measurements indicated in table 4.

TABLE N°4: Burner primary air regulation (indicative)

Burner

Type of gas

Broiler

Inches (mm)

fully open

NG (Natural Gas)

LP (Propane Gas)

Work surface burner adjustment: follow the instructions below to adjust the work surface burner minimum:

1) Light the burner and set the knob to the MINIMUM position (small flame).

2) Remove the knob of the valve that is press fit on the rod of that valve.

3) The cooker is equipped with safety valves, use a small slotted screwdriver the choke valve located on the valve body

and turn the choke screw to the right or left until the burner flame is adjusted to minimum

4) Make sure that the flame does not go out when switching quickly from the MAXIMUM to the MINIMUM position.

Oven burner adjustment: follow the instructions below to adjust the minimum:

1) Light the burner setting the knob to the MAXIMUM position.

2) Close the oven door and operate the oven for at least 10 minutes.

3) Set the knob to the MINIMUM position and then remove it.

4) With a slotted screwdriver turn the choking screw (by-pass screw at the left side of the thermostat bar) and, while

observing the flame at the same time through the cooker porthole, evaluate the consistency of the flame so it remains on

when switching quickly from the MINIMUM to the MAXIMUM position.

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING: The above-mentioned adjustment should be made only for natural gas, while for operation with

liquid gas the screw must be locked at the end in a clockwise direction. The broiler burner always

operates at maximum and therefore no minimum adjustment is required.

SERVICE & MAINTENANCE INSTRUCTIONS

Service and maintenance only to be carried out by an authorised person

To replace parts such as burners, valves and electric components, the appliance must be open removing the worktop.

Note: if the valves must be replaced, first disassemble the ignitions switches wires.

It is recommended to replace the valve gaskets each time the valve is replaced, thus ensuring a perfect seal between the

body and the gas train.

WARNING: After first installation of the appliance or after any service intervention concerning main gas parts of

the appliance, make the leak test using water with soap on the gas connections in order to verify the correct

installation. Do not use fire for gas leak testing.

To replace the oven bulb, just unscrew the protection cap that projects out inside the oven. (Fig.19) WARNING:

Disconnect power before servicing unit.

In order to remove the oven door make sure to block the ihinges with a screw driver.

Call an autorised service person for this operation that can be dangerous

USER MANUAL

WARNINGS:

Keeping appliance area clear and free from combustible materials, gasoline and other flammable

vapors and liquid.

Do not store dangerous or flammable material in the cabinet areas above appliance; store them in a

safe place in order to avoid potential hazards.

Do not use aerosol sprays in the vicinity of this appliance while it is in operation

Do not use oven doors as support or for sit-down.

Do not use oven cavity as storage compartment.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTROL PANEL DESCRIPTION

On the control panel, small symbols show the function of each knob or key. Here as follows are the several controls that

a cooker can have:

the symbol

shows the disposition of burners on the worktop, the full dot identifies the burner in object (in this

case the front burner on the right).

the symbol

shows the running of oven or broiler

shows the swicth for the oven fan and oven light

shows the swicth for the oven light

the symbol

USING BURNERS

A diagram is etched on the control panel above each knob which indicates which burner corresponds to that

knob.

(flame)

Manual ignition:

Manual ignition is always possible even when the power is cut off or in the event of prolonged power failure.

Turn the knob that corresponds to the burner selected counterclockwise to the MAXIMUM position at the etched star

(large flame) and place a lit match up to the burner.

Automatic electric ignition:

Turn the knob that corresponds to the burner selected anticlockwise direction to the MAXIMUM position at the etched

star (large flame) and then press the knob down to activate the spark ignition. Once ignited, keep pressing the knob for

about 10 seconds to allow the flame to heat the thermocouple. If the burner does not remain alight after releasing the

knob repeat the above procedure,

Note: It is recommended not to try to ignite the burner if the relative flame cap is not in the correct position

Note: Dual burner is composed by two burner (inside and outside); each one operates under the relative gas valve

indipendently from the other one.

Download from Www.Somanuals.com. All Manuals Search And Download.

Tips for using burners correctly:

WARNING: During use of each gas burner(s) adjust the burner flame size properly so it does not extend beyond

the edge of the cooking utensil. This is an instruction based on safety considerations

- Use suitable pots for each burner (see Fig. and Table )

- When the liquid is boiling, turn down the knob to the MINIMUM position.

- Always use pots with a cover.

Correct flame aspect: verify that aspect flame of the worktop burners be completely blue and with an aspect as

indicated in figure(flame)

Table

Burner

Small

Recommended pan diameters inches (mm)

3½”-51/2”(90 – 140)

Medium

Large

51/2”- 101/4”(140 – 260)

71/8”- 101/4” (180 – 260)

Dual burner

82/3”-101/4” (220 – 260)

WARNING: check the position of the burner caps before operation.

Correct usage of pans:

- Dry the bottom of the pan before placing it on the hotplate.

- Use pots with a flat, thick bottom, except for wok cooking.

- When using the burners, ensure that the handles of the pans are correctly positioned. Keep children away from the

appliance.

- When cooking foods with oil and fat, which are very flammable, the user should not leave the appliance unattended.

WOK PAN: To use the wok pan, please utilize a suitable wok adaptor grid; wok pan external diameter shall not be less

than 10” (25cm) and not more than 16”(40cm).

WARNING: If the power is cut off, the burners can be lit with matches.

The burners equipped with a safety thermocouple can only be lit when the knob is in the MAXIMUM position (large flame

etching).

USING THE GAS OVEN

All the gas oven cookers are equipped with a thermostat and safety device to adjust the cooking temperature. The oven

temperature is set by turning the knob counterclockwise to match the indicator with the temperature selected. The gas

oven is combined with a gas broiler. See the specific pages for use information.

WARNING: If the burner flames are extinguished accidentally, turn off the control knob and do not try to relight

the oven until after at least 1 minute.

TABLE N°7

THERMOSTAT SETTING TEMPERATURE °F TEMPERATURE °C

MIN.

MED-LOW

MED.

MED-HI

MAX.

270

320

350

425

500

132

160

175

220

260

Download from Www.Somanuals.com. All Manuals Search And Download.

The oven burner can be ignited in different ways:

- Manual lighting (it is always possible even when the power is cut off):

To light the oven, open the oven door and turn the knob at maximum position . At the same time put a lit match next to

the ignition tube that is visible on the oven level . Then press the thermostat knob (this makes the gas start to flow) and

keep it pressed, after the burner has been completely lit, for 10 seconds. Release the knob and make sure that the

burner remains on, otherwise repeat the operation.

- Electric ignition

In this case, first open the oven door, then turn the knob to the maximum temperature setting. Then press the thermostat

knob to start the gas flow and the ignition spark. Wait about 10 seconds after the burner has been completely lit and then

release the knob. Make sure that the burner remains on, otherwise repeat the operation.

The ignition device should not be used for more than 15 seconds. If after that period the burner still has not

been lit, do not use the device and open the door of the room or wait at least 60 seconds before trying to light

the oven again.

WARNING: when trying to light the oven, the door must always be open.

The gas oven operation is indicated by a blue light

Verify that aspect flame of the oven burner be completely blue and with an aspect as indicated in figure

NOTICE: when using the oven for the first time it should be operated for 15-30 minutes at a temperature of

about 500°F/260°C without cooking anything inside in order to eliminate any moisture and odours from the

internal insulation.

During normal oven use, after lighting the burner and setting the desired temperature, wait about 15 minutes before

putting in any food to preheat the oven.

The oven is equipped with 4 guides at different heights level which can be used to insert shelves or the tray. To keep the

oven as clean as possible it is recommended to cook meat on the tray or on the shelf that has been inserted inside the

tray. The table below lists the general cooking times and the position of the tray for different types of foods. Personal

experience will help to determine any variations in the values reported in the table. In any case, it is recommended to

follow the instructions of the specific recipe being used.

This type of oven is equipped with a fan. The fan convection creates forced-air circulation in the horizontal direction.

Thanks to this type of operation, the ventilated oven can be used for different types of cooking at the same time, without

changing the taste of each food. Hot-air circulation guarantees a uniform distribution of heat. Pre-heating the oven is not

necessary, but for very delicate pastries, it is recommended to heat the oven before inserting the trays.

The convection system partially changes the various notions about traditional cooking. Meat no longer needs to be

turned while it is cooking and the rotisserie is no longer needed to cook a roast on the spit. Just put the meat directly on

the shelf.

GAS OVEN COOKING TABLE

TEMP °F/ °C

HEIGHT

MINUTES

MEAT

PORK ROAST

BEEF ROAST (YOUNG STEER)

BEEF ROAST

VEAL ROAST

LAMB ROAST

430/220

480/250

465/240

430/220

445/230

450/235

430/220

450/235

450/225

450/235

60-70

50-60

60-70

45-55

55-65

40-50

50-60

60-70

45-60

40-45

ROAST BEEF

ROAST HARE

ROAST RABBIT

ROAST TURKEY

ROAST GOOSE

ROAST DUCK

ROAST CHICKEN

FISH

390-440/200-225

390/200

15-25

35-40

PASTRY

FRUIT PIE

Download from Www.Somanuals.com. All Manuals Search And Download.

TEA CAKE

BRIOCHES

375/190

345/175

450/235

375/190

430/220

355/180

375/190

430/220

480/250

430/220

50-55

25-30

30-40

15-20

20-30

SPONGE CAKE

RING CAKE

SWEET PUFF PASTRIES

RAISIN LOAF

STRUDEL

SAVOIA COOKIES

APPLE FRITTERS

SAZOIARDI SANDWICH

TOAST SANDWICH

BREAD

PIZZA

To activate the convection fan use the selector placed on control panel.

Turn the knob anti clockwise for activation of the convection fan +light

Turn the knob clockwise to turn on the oven light.

CONVECTION GAS OVEN COOKING TABLE

TEMP °F/ °C

HEIGHT

MINUTES

MEAT

PORK ROAST

BEEF ROAST (YOUNG STEER)

BEEF ROAST

VEAL ROAST

LAMB ROAST

320-340/160-170

340-355/170-180

340-375/170-190

320-355/160-180

285-320/140-160

355-375/180-190

340-355/170-180

320-340/160-170

320-355/160-180

340-355/170-180

355/180

70-100

65-90

40-60

65-90

100-130

40-45

ROAST BEEF

ROAST HARE

30-40

ROAST RABBIT

ROAST TURKEY

ROAST GOOSE

ROAST DUCK

ROAST CHICKEN

80-100

160-240

120-160

100-160

70-90

FISH

320-355/160-180

3 / 4

PASTRY

FRUIT PIE

TEA CAKE

BRIOCHES

SPONGE CAKE

RING CAKE

SWEET PUFF PASTRIES

RAISIN LOAF

STRUDEL

SAVOIA COOKIES

APPLE FRITTERS

SAZOIARDI SANDWICH

TOAST SANDWICH

BREAD

355-390/180-200

390-430/200-220

340-355/170-180

390-445/200-230

320-355/160-180

355-390/180-200

445-480/230-250

320/160

300-355/150-180

355-390/180-200

340-355/170-180

445-480/230-250

390-430/200-220

40-50

40-45

40-60

25-35

35-45

20-30

30-40

25-35

50-60

18-25

30-40

PIZZA

USING THE GAS BROILER

The gas broiler is controlled with the same gas oven knob, but turning it clockwise instead of counterclockwise (see the

gas oven use instructions), matching the symbol with the indicator. The broiler burner always operates at maximum and

therefore there is no minimum position. In addition, it is equipped with a safety device to prevent the flame from going

out. The gas broiler can also be ignited in different ways:

Download from Www.Somanuals.com. All Manuals Search And Download.

- Manual lighting: Just completely open the oven door, turn the knob so that the relative symbol matches the indicator,

while pressing the knob, and, at the same time, put a lit match next to the burner. Make sure that the burner is

completely lit and after about 10 seconds release the knob. Make sure that the burner remains on, otherwise repeat the

operation.

- Electric ignition: In this case, completely open the oven door, turn the knob so that the relative symbol matches the

indicator and, while keeping the knob pressed, press the knob with the spark symbol. Wait about 10 seconds after the

burner has been completely lit and then release the knob. Make sure that the burner remains on, otherwise repeat the

operation.

ATTENTION: To use broiler please utilize the proper broiler grid installed inside the grid enamelled tray supplied

with the appliance; broiler tray shall be supported by oven grid.

WARNING: As with the oven, the broiler must be lit with the door completely open.

The gas broiler can be used to broil foods on the oven shelf .

The gas broiler operation is indicated by a blue light

IMPORTANT: when broiling food keep the door closed..

Verify that aspect flame of the broiler burner be completely blue and with an aspect as indicated in figure

Note: The use of a gas cooking appliance produces heat and humidity in the room where it is installed. Therefore, proper

ventilation in the room is needed and natural ventilation openings must remain unobstructed and activating the

mechanical exhaust fan/range hood. Intensive and continuous use of the appliance may require additional ventilation, for

example by opening a window, or increasing the power of the mechanical exhaust fan/range hood, if installed.

Note: the cooker is equipped with cooling fan starting each time gas oven/broiler are in operation. The cooling

air frow come outside from the space existing between control and panel oven door avoiding the overheating

of their external surfaces during oven/broiler use.

CLEANING THE APPLIANCE:

Never use abrasive cleaners

Before cleaning the appliance it should be disconnected from the power supply.

Cleaning the work surface: periodically clean the burner heads, the cast iron pan supports and the burner caps using

warm water.

Any spillage must always be removed as soon as possible using a rag.

If it become difficult to open or close a valve, do not force it, but immediately request the assistance of the

technical service personnel.

Cleaning the enamelled parts: Enamelled parts should be cleaned frequently with soapy water. Never use abrasive

powder. Do not leave acidi or alkaline substances on the enamelled parts (such as vinegar, lemon juice, salt, tomato

sauce, etc.) and do not wash the enamelled parts while they are still hot.

Cleaning the stainless steel parts: Clean the parts with soapy water and dry them with a soft cloth. The shine is

maintained by periodically using specific stainless steel cream cleaner. Never use abrasive powders. Use specific

stainless steel cream cleaner to eliminate the glue remains afther the elimination of the blue plastic protection film on the

worktop after installation.

Cleaning the burner caps: Lift the burner caps from the burner heads and wash them in soapy water and dry

thoroughly. Before replacement on the burner head ensure that the holes are not clogged.

Cleaning the inner glass door: Clean the glass with warm soapy water using a sponge. A spatula can be used to

remove burner fat if used gently.

ATTENTION: while cleaning the door make sure to avoid any spillage in the venting holes on the top part of the door. To

clean inside the door it is necessary to disassemble the door through a service engineer.

ATTENTION: for further details about cleaning of the appliance, please contact your applliance retailer.

Download from Www.Somanuals.com. All Manuals Search And Download.

AFTER SALE SERVICE:

Please note here below details for after save service.

Refer to warranty certificate for warranty condiftions

Dealer /Importer:

Name, address, phone

SERVICE CENTERS

Name

Phone

MANUFACTURER:

BERTAZZONI SPA

VIA PALAZZINA, 8 – 42016 – GUASTALLA (REGGIO E.) ITALY

Tel. 0522/226411 – telefax 0522/226440 – http://www.bertazzoni-italia.com

Download from Www.Somanuals.com. All Manuals Search And Download.

SPARE PART LIST

NUMBER

COMPONENT

202387

202432

306003

404213

504160

504161

504162

504187

504186

202450

202439

202436

101387

101048

202440

202262

410571

410572

308034

202444

309010

309141

306024

415071

415054

415084

415077

415064

404187

404212

404497

202407

405077

404188

404117

410604

125055

125049

125041

125053

504775

505013

508025

508021

508036

508034

508026

603020

603019

602039

608046

601991

608047

503121

504128

504129

504130

504189

408058

604070

510507

510508

510509

510511

502148

502150

502179

DESCRIPTION

BURNERS FLASK

PART FOR DUAL WOK AND SEMI RAPID BURNERS

THERMOSTAT CLIP

WORKTOP FRONTGUARD

COVER FOR SMALL FLAME SPREADER

COVER FOR MEDIUM BURNER

COVER FOR RAPID BURNER

COVER IN FOR DUAL BURNER FLAME SPREADER

COVER OUT FOR DUAL BURNER FLAME SPREADER

UP SUPPORT FOR AXIAL COOLIN FAN

DOWN SUPPORT FOR AXIAL COOLIN FAN

INSIDE FLAP DOOR

105

106

109

117

120

138

160

205

206

207

274

311

329

385

424

425

427

429

430

441

442

443

444

446

447

473

478

544

546

561

562

564

566

567

611

612

620

623

648

649

667

670

671

672

675

702

715

760

761

762

764

881

883

884

PROTECTION FOR FAN ASSISTED OVEN

BLACK OVEN DRIP TRAY

DISHWARMER BOTTOM

BRIDLE FOR FIXING GAS VALVES

PROFILE FOR GLASS DOOR

BUMPER

CROSS MEMBER

RING FOR GRID SUPPORT

INSIDE DOOR SPACER

SPRING FOR SPARK PLUG

SPARK PLUG FOR DUAL BURNER

SPARK PLUG 350MM

SPARK PLUG FOR OVEN

SPARK PLUG FOR GRILL

ACCUMULATOR 4U

RIGHT GRID FOR OVEN

SHELF OVEN

GRID FOR TRAY

FLASK HINGE

OVEN DOOR HINGE

LEFT GRID FOR OVEN

SIMMER PLATE

FLAP DOOR

FLAP DOOR BURGUNDY RED

FLAP DOOR BLACK

FLAP DOOR RED

FLAP DOOR PURE WHITE

OVEN BURNER + SPARK PLUG + THERMOC.

SUPPORT FOR GRILL BURNER NOZZLE

TERMOCOUPLE MM300

TERMOCOUPLE MM600

THERMOCOUPLE OVEN BURNER

TERMOCOUPLE ULTRA-RAPID BURNER

THERMOCOUPLE GRILL BURNER

OVEN CONVECTION FAN

COOLING FAN

COMMUTATOR

OVEN BULB WITH HOLDER

TERMINAL SEPARATOR

SMALL WARNING LIGHT

THERMOSTAT

SMALL FLAME SPREADER

MEDIUM FLAME SPREADER

RAPID FLAME SPREADER

ULTRA RAPID FLAME SPREADER

ADAPTER FOR WOK BURNER PAN SUPPORT

DASYCHAIN SWITCH

SMALL BURNER

SEMI RAPID BURNER

RAPID BURNER

DUAL BURNER

GAS VALVE BY PASS 036 SEMI-RAPID

GAS VALVE BY PASS 065 DUAL OUTER

GAS VALVE BY PASS 029 SMALL/DUAL INNER

Download from Www.Somanuals.com. All Manuals Search And Download.

886

917

502180

200327

125003

125027

125033

125045

202389

202214

201168

308035

403343

408068

408063

202360

401904

401905

401906

401961

401962

910711

403435

406396

411093

602042

411094

406395

410605

125056

125050

125052

125054

210577

309119

501761

505056

201173

202435

608045

608025

200348

501755

501759

501760

202390

414048

414031

501762

201166

201167

202443

410606

501758

501756

501757

101383

101384

101408

101385

101389

101388

202437

202497

405078

200328

125002

125026

125032

125044

200329

125001

125025

125031

125043

504776

GAS VALVE BY PASS 047 RAPID

STAINLESS STEEL SIDE

SIDE BURGUNDY RED

917

SIDE BLACK

917

SIDE RED

917

SIDE PURE WHITE

929

RIGHT VERTICAL VENT

FEET SUPPORT

930

940

FIXING FOR WORK TABLE

BUMPER FOR PAN SUPPORT

HANDLE TERMINAL

943

947

964

CAST IRON PAN SUPPORT

CAST IRON PAN SUPPORT 2 BURNERS

WORK TABLE FIXING

965

972

1041

1043

1044

1046

1047

1143

1406

1407

1411

1415

1419

1421

1508

1602

1603

1608

1609

1614

1615

1617

1622

1624

1627

1628

1631

1639

1644

1645

1646

1685

1686

1687

1705

1801

1803

1804

2016

2017

2031

2032

2057

2097

2098

2099

4106

4301

4302

5140

GAS VALVE KNOB

GAS THERMOSTAT KNOB

ELECTRIC KNOB

DUAL IN KNOB

DUAL OUT KNOB

UPSTAND KIT

OVEN DOOR HANDLE

OVEN DOOR GLASS

GASKET FOR OVEN FRONT 3 SIDE

THERMOSWITCH

GASKET FOR OVEN FRONT 1 SIDE

INNER OVEN GLASS

STAINLESS STEEL OVEN DOOR

OVEN DOOR BURGUNDY RED

OVEN DOOR BLACK

OVEN DOOR RED

OVEN DOOR PURE WHITE

CONTROL PANEL

BRIDLE FOR FIXING GAS VALVES/THERMOSTAT

ALL.TUBE FOR OVEN BURNER

SUPPORT FOR OVEN BURNER NOZZLE

BACK PANEL

CONTROL SUPPORT

SMALL BLUE BUD

SMALL RED BUD

WORK TABLE

GAS COLLECTOR

TUBE FOR RIGHT FRONT BURNER

TUBE FOR RIGHT BACK BURNER

LEFT VERTICAL VENT

S.STEEL LEG

BASE FOR LEGS

GRILL THERMOSTAT TUBE

REAR VENT STACK

FRONT VENT STACK

BACK ENCLOSURE METAL PANEL

OVEN GLASS SUPPORT

TUBE FOR LEFT BACK BURNER

TUBE FOR EXTERNAL DUAL BURNER

TUBE FOR INTERNAL DUAL BURNER

OVEN SIDE PANEL BLACK RIGHT

OVEN SIDE PANEL BLACK LEFT

UPPER PART FOR BODY

BACK OVEN BODY

FRONT PANEL MUFFLE

OVEN BOTTOM PANEL BLACK

OVEN BURNER BASE

OVEN BASE

HINGE FOR FLAP DOOR

RIGHT SIDE PROFILE

RIGHT SIDE PROFILE BURGUNDY RED

RIGHT SIDE PROFILE BLACK

RIGHT SIDE PROFILE RED

RIGHT SIDE PROFILE PURE WHITE

LEFT SIDE PROFILE

LEFT SIDE PROFILE BURGUNDY RED

LEFT SIDE PROFILE BLACK

LEFT SIDE PROFILE RED

LEFT SIDE PROFILE PURE WHITE

GRILL BURNER

Download from Www.Somanuals.com. All Manuals Search And Download.

Black Decker Coffee Grinder CBM7 User Manual
Blue Rhino Charcoal Grill CBT711W C User Manual
Bolens Lawn Mower 13000 User Manual
Brookstone Work Light 740157 User Manual
Brother Toaster PT H500LI User Manual
Cabletron Systems Switch 6H128 08 User Manual
CFM Ventilation Hood CDB 07 User Manual
Chaney Instrument Weather Radio L5C0964TX User Manual
Char Broil Gas Grill 466250511 User Manual
Chauvet Indoor Furnishings DMX 60 User Manual