W1060
Digital Projector
User Manual
Welcome
Download from Www.Somanuals.com. All Manuals Search And Download.
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information
technology equipment. However, to ensure safe use of this product, it is important that you
follow the instructions mentioned in this manual and marked on the product.
Safety Instructions
1.
Please read this manual before you
operate your projector. Save it for
future reference.
4.
In some countries, the line voltage is
NOT stable. This projector is designed
to operate safely within a mains
voltage between 100 to 240 volts AC,
but could fail if power cuts or surges
of 10 volts occur. In areas where the
mains voltage may fluctuate or cut
out, it is recommended that you
connect your projector through a
power stabilizer, surge protector or
uninterruptible power supply (UPS).
2.
Do not look straight at the projector
lens during operation. The intense
light beam may damage your eyes.
5.
Do not block the projection lens with
any objects when the projector is
under operation as this could cause
the objects to become heated and
deformed or even cause a fire. To
temporarily turn off the lamp, press
BLANK on the projector or remote
control.
3.
Refer servicing to qualified service
personnel.
Important safety instructions
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions (Continued)
6.
The lamp becomes extremely hot
during operation. Allow the
projector to cool for approximately
45 minutes prior to removing the
lamp assembly for replacement.
9.
Do not place this product on an
unstable cart, stand, or table. The
product may fall, sustaining serious
damage.
10. Do not attempt to disassemble this
projector. There are dangerous high
voltages inside which may cause
death if you should come into
contact with live parts. The only
user serviceable part is the lamp
which has its own removable cover.
Under no circumstances should you
ever undo or remove any other
covers. Refer servicing only to
suitably qualified professional
service personnel.
7.
Do not operate lamps beyond the
rated lamp life. Excessive operation
of lamps beyond the rated life could
cause them to break on rare
occasions.
8.
Never replace the lamp assembly or
any electronic components unless
the projector is unplugged.
11. When the projector is under
operation, you may sense some
heated air and odor from its
ventilation grill. It is a normal
phenomenon and not a product
defect.
4
Important safety instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions (Continued)
12. Do not place this projector in any of
the following environments.
13. Do not block the ventilation holes.
- Do not place this projector on a blanket,
bedding or any other soft surface.
- Do not cover this projector with a cloth or
any other item.
- Do not place inflammables near the
projector.
- Space that is poorly ventilated or
confined. Allow at least 50 cm clearance
from walls and free flow of air around the
projector.
- Locations where temperatures may
become excessively high, such as the
inside of a car with all windows rolled up.
- Locations where excessive humidity, dust,
or cigarette smoke may contaminate
optical components, shortening the
projector's life span and darkening the
image.
If the ventilation holes are seriously
obstructed, overheating inside the
projector may result in a fire.
14. Always place the projector on a level,
horizontal surface during operation.
- Do not use if tilted at an angle of more
than 10 degrees left to right, nor at angle
of more than 15 degrees front to back.
Using the projector when it is not fully
horizontal may cause a malfunction of, or
damage to, the lamp.
- Locations near fire alarms
- Locations with an ambient temperature
above 35°C / 95°F
- Locations where the altitudes are higher
than 3000 m (10000 feet).
15. Do not stand the projector on end
vertically. Doing so may cause the
projector to fall over, causing injury or
resulting in damage to the projector.
3000 m
(10000 feet)
0 m
(0 feet)
Important safety instructions
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions (Continued)
16. Do not step on the projector or place
any objects upon it. Besides probable
physical damage to the projector, doing
so may result in accidents and possible
injury.
Ceiling mounting the projector
We want you to have a pleasant
experience using your BenQ projector,
so we need to bring this safety matter
to your attention to prevent possible
damage to person and property.
If you intend to mount your projector
on the ceiling, we strongly recommend
that you use a proper fitting BenQ
projector ceiling mount kit and that
you ensure it is securely and safely
installed.
If you use a non-BenQ brand projector
ceiling mount kit, there is a safety risk
that the projector may fall from the
ceiling due to an improper attachment
through the use of the wrong gauge or
length screws.
You can purchase a BenQ projector
ceiling mount kit from the place you
purchased your BenQ projector. BenQ
recommends that you also purchase a
separate Kensington lock compatible
security cable and attach it securely to
both the Kensington lock slot on the
projector and the base of the ceiling
mount bracket. This will perform the
secondary role of restraining the
projector should its attachment to the
mounting bracket become loose.
17. Do not place liquids near or on the
projector. Liquids spilled into the
projector may cause it to fail. If the
projector does become wet, disconnect
it from the power supply's wall socket
and call BenQ to have the projector
serviced.
18. This product is capable of displaying
inverted images for ceiling mount
installation.
Use only BenQ's Ceiling Mount Kit for
mounting the projector and ensure it
is securely installed.
6
Important safety instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user-friendly
design to deliver high reliability and ease of use.
The projector offers the following features.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Quick auto search speeding up the signal detecting process
Selectable password protected function
3D color management allowing color adjustments to your liking
Selectable quick cooling function makes the projector cool in a shorter time
One-key auto-adjustment to display the best picture quality
Digital keystone correction to correct distorted images
Adjustable color balance control for data/video display
High brightness projection lamp
Ability to display 1.07 billion colors
Multi-language On-Screen Display (OSD) menus
Switchable normal and economic modes to reduce the power consumption
Component HDTV compatibility (YPbPr)
High quality manual zoom lens
Built-in speakers provide mixed mono audio when an audio input is connected
Powerful AV function to provide high quality video image
HDCP compatibility
Dual HDMI inputs
Auto keystone function to correct image keystoning automatically
•
•
The apparent brightness of the projected image will vary depending on the ambient
lighting conditions, selected input signal contrast/brightness settings, and is directly
proportional to projection distance.
The lamp brightness will decline over time and may vary within the lamp manufacturers
specifications. This is normal and expected behavior.
Introduction
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Shipping contents
Carefully unpack and verify that you have all of the items shown below. If any of these items
are missing, please contact your place of purchase.
Standard accessories
The supplied accessories will be suitable for your region, and may differ from those
illustrated.
Projector
Remote control with battery
(UK)
(US)
(KOREA)
(CHINA)
(JAPAN)
(AU)
(EU)
Power cord
VGA cable
W1060
Video Projector
Quick Start Guide
Dansk
Suomi
Norsk
2011
P/N:5B.J5701.001
2011
P/N: 4J.J5701.001
Quick start guide
User manual CD
Warranty card*
Optional accessories
1.
2.
Spare lamp kit
Ceiling mount kit
3.
4.
Soft carry case
RS-232 cable
*The warranty card is only supplied in specific regions. Please consult your dealer for detailed
information.
8
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector exterior view
1.
2.
3.
4.
5.
Vent (heated air exhaust)
Lamp cover
Quick-release button
Projection lens
External control panel
details.)
Front/upper side
6.
7.
8.
9.
Top IR remote sensor
Focus ring and Zoom ring
Vent (cool air intake)
Front IR remote sensor
10. COMPONENT input jacks
11. S-VIDEO input jack
12. USB input jack
Rear/lower side
13. VIDEO input jack
14. PC input jack
15. HDMI 1 input jack
16. HDMI 2 input jack
17. Rear adjuster foot
COMPUTER
PC
COMPONENT
S-IDEO
VIDEO
HDMI-1
HDMI-2
RS-232
AUDIO
USB
18. Kensington anti-theft lock slot
19. AUDIO input jack (right)
20. AUDIO input jack (left)
21. AUDIO input jack
22. AUDIO output jack
23. Quick-release foot
24. RS-232 control port
25. AC power cord inlet
L
AUDIO
R
OUT
IN
Introduction
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and functions
Projector
7.
8.
TEMPerature indicator light
Lights up red if the projector's
temperature becomes too high. See
"Indicators" on page 58 for details.
Keystone/Arrow keys
(
/
Up,
/
Down)
Manually corrects distorted images
resulting from an angled projection. See
details.
9.
LAMP indicator light
Indicates the status of the lamp. Lights up
or flashes when the lamp has developed a
details.
1.
2.
3.
FOCUS/ZOOM Ring
10. AUTO
Automatically determines the best picture
Used to adjust the projected image
appearance. See "Fine-tuning the image size
and clarity" on page 31 for details.
POWER indicator light
timings for the displayed image. See
details.
Lights up or flashes when the projector is
under operation. See "Indicators" on page
58 for details.
11.
Right/Increase volume level
Increases volume. See "Adjusting the
sound level" on page 42 for details.
When the On-Screen Display (OSD)
menu is activated, the #4, #8 and #11 keys
are used as directional arrows to select the
desired menu items and to make
adjustments. See "Using the menus" on
page 26 for details.
MENU/EXIT
Turns on the On-Screen Display (OSD)
menu. Goes back to previous OSD menu,
exits and saves menu settings.
details.
4.
5.
Left/Decrease volume level
Decreases volume. See "Adjusting the
sound level" on page 42 for details.
12. MODE/ENTER
Selects an available picture setup mode.
for details.
POWER
Toggles the projector between standby
mode and on.
Enacts the selected On-Screen Display
(OSD) menu item. See "Using the menus"
on page 26 for details.
43 for details.
13. SOURCE
Displays the source selection bar. See
details.
6.
BLANK
the image" on page 40 for details.
10
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
7.
Up cursor/Keystone (
/
)
: Navigates and changes settings in the
OSD. See "Using the menus" on page
26 for details.
: Manually corrects distorted images
resulting from an angled projection.
for details.
8.
Left cursor/Decrease volume level (
/
)
: Navigates and changes settings in the
OSD. See "Using the menus" on page
26 for details.
: Decreases volume. See "Adjusting
details.
MODE/ ENTER
9.
MODE: Choose a suitable preset mode
for usage environment.
ENTER: Enter key for OSD menu.
10. MENU/ EXIT
MENU: Turns on the On-Screen Display
(OSD) menu.
EXIT: Goes back to previous OSD menu,
exits and saves menu settings.
1.
IR transmitter
11. MUTE
Transmits signal to projector.
LED indicator
2.
3.
Mutes the built-in speaker.
12. USER 1/ User 2/ User 3
Select the User memory settings.
13. BRIGHT
Lights only when the key is pressed
POWER ON
Toggles the projector between standby
mode and on. See "Starting up the
projector" on page 25 for details.
VIDEO
Displays the VIDEO source selection. See
"Switching input signal" on page 29 for details.
COMP
Displays the COMPONENT source
selection. See "Switching input signal" on
page 29 for details.
Displays the BRIGHTNESS setting bar.
details.
4.
5.
14. COLOR
Displays the COLOR setting bar. See
37 for details.
15. INFO
Starts the INFORMATION function.
6.
HDMI 1
Displays the HDMI 1 source selection. See
details.
Introduction
11
Download from Www.Somanuals.com. All Manuals Search And Download.
16. LIGHT
Turns on or off the remote control backlight
23. ASPECT
Select the display aspect ratios. See
for about 10 seconds. Pressing any other key
while the backlight is on keeps the backlight
on for a further 10 seconds.
details.
24. FREEZE
Freeze/unfreezes the on-screen picture.
details.
17.
POWER OFF
the projector" on page 43 for details.
25. AUTO
18. S-VIDEO
Automatically determines the best picture
timings for the displayed image.
26. SHARP
Displays the S-VIDEO source selection.
details.
19. PC
Displays the SHARPNESS setting bar. See
"Adjusting Sharpness" on page 36 for details.
27. CONTRAST
Displays the PC source selection. See
"Switching input signal" on page 29 for details.
20. HDMI 2
Displays the CONTRAST setting bar. See
"Adjusting Contrast" on page 36 for details.
28. BLANK
Displays the HDMI 2 source selection. See
details.
Hides the screen picture. See "Hiding the
image" on page 40 for details.
21. Right cursor/Increase volume level (
/
)
29. TINT
Displays the TINT setting bar. See
"Adjusting Tint" on page 36 for details.
30. TEST
Displays the test pattern.
: Navigates and changes settings in the
OSD. See "Using the menus" on page
26 for details.
: Increase Volume.
22. Down cursor/Keystone (
/
)
: Navigates and changes settings in the
OSD. See "Using the menus" on page
26 for details.
: Manually corrects distorted images
resulting from an angled projection.
for details.
12
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control effective range
Infra-Red (IR) remote control sensor is located on the
front and the top of the projector. The remote control
must be held at an angle within 30 degrees
perpendicular to the projector's IR remote control
sensor to function correctly. The distance between the
remote control and the sensor should not exceed 7
meters (~ 23 feet).
Make sure that there are no obstacles between the
remote control and the IR sensor on the projector that
might obstruct the infra-red beam.
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Replacing the remote control battery
1.
2.
3.
Remove the battery compartment cover by
sliding the cover in the direction of the
arrow.
Insert the supplied batteries taking note of
the polarity (+/-) as shown here.
Replace the cover.
•
•
•
•
•
•
Avoid excessive heat and humidity.
There may be battery damage if the battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the battery manufacturer.
Dispose of the used battery according to the battery manufacturer’s instructions.
Never throw a battery into a fire. There may be danger of an explosion.
If the battery is dead or if you will not be using the remote control for a long time, remove
the battery to prevent damage to the remote control from possible battery leakage.
14
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Positioning your projector
Choosing a location
Your room layout or personal preference will dictate which installation location you select.
Take into consideration the size and position of your screen, the location of a suitable power
outlet, as well as the location and distance between the projector and the rest of your
equipment.
Your projector is designed to be installed in one of four possible installation locations:
1.
Front Table
Select this location with the projector placed on a table in
front of the screen. This is the most common way to
position the projector for quick setup and portability.
2.
Front Ceiling
Select this location with the projector suspended upside-
down from the ceiling in front of the screen.
Purchase the BenQ Projector Ceiling Mounting Kit from
your dealer to mount your projector on the ceiling.
Set Front Ceiling in the SYSTEM SETUP: Basic >
Projector Position menu after you turn the projector on.
3.
Rear Table
Select this location with the projector placed on a table
behind the screen.
Note that a special rear projection screen is required.
Set Rear Table in the SYSTEM SETUP: Basic > Projector
Position menu after you turn the projector on.
4.
Rear Ceiling
Select this location with the projector suspended upside-
down from the ceiling behind the screen.
Note that a special rear projection screen and the BenQ
Projector Ceiling Mounting Kit are required for this
installation location.
Set Rear Ceiling in the SYSTEM SETUP: Basic >
Projector Position menu after you turn the projector on.
*To set the projector position:
SYSTEM SETUP: Basic
1. Press MENU/EXIT on the projector or remote control
and then press until the SYSTEM SETUP:
Basic menu is highlighted.
English
Front Table
Language
Projector Position
Menu Settings
Operation Settings
/
Remote Receiver
Background Color
Splash Screen
Front+Top
Blue
BenQ
2. Press
/
to highlight Projector Position and press
/
until the correct position is selected.
Menu/Back Exit
PC
Positioning your projector
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Obtaining a preferred projected image size
The distance from the projector lens to the screen, the zoom setting (if available), and the
video format each factors in the projected image size.
16:9 is the native aspect ratio. W1060 can project a complete 16:9 (widescreen) image.
4:3 aspect image in a 16:9
aspect display area
16:9 aspect image scaled to a 4:3 aspect
display area
The projector should always be placed horizontally level (like flat on a table), and positioned
directly perpendicular (90° right-angle square) to the horizontal center of the screen. This
prevents image distortion caused by angled projections (or projecting onto angled surfaces).
The modern digital projector does not project directly forward (like older style reel-to-reel
film projectors did). Instead, digital projectors are designed to project at a slightly upward
angle above the horizontal plane of the projector. This is so that they can be readily placed
on a table and will project forward and upwards onto a screen positioned so that the bottom
edge of the screen is above the level of the table (and everyone in the room can see the
screen).
If the projector is mounted on a ceiling, it must be mounted upside-down so that it projects
at a slightly downward angle.
of the projected image to be vertically offset from the horizontal plane of the projector.
When ceiling mounted, this refers to the top edge of the projected image.
If the projector is positioned further away from the screen, the projected image size
increases, and the vertical offset also increases proportionately.
When determining the position of the screen and projector, you will need to account for
both the projected image size and the vertical offset dimension, which are directly
proportional to the projection distance.
BenQ has provided a table of screen sizes to assist you in determining the ideal location for
projector you are using. There are two dimensions to consider, the perpendicular horizontal
distance from the center of the screen (projection distance), and the vertical offset height of
the projector from the horizontal edge of the screen (offset).
16
Positioning your projector
Download from Www.Somanuals.com. All Manuals Search And Download.
How to determine the position of the projector for a given
screen size
1.
2.
Select your screen size.
Refer to the table and find the closest match to your screen size in the left columns
This is the projection distance.
3.
4.
offset in mm" value. This will determine the final vertical offset placement of the
projector in relation to the edge of the screen.
The recommended position for the projector is aligned perpendicular to the
horizontal center of the screen, at the distance from the screen determined in step 2
For example, if you are using a 120-inch screen, the average projection distance is 4636 mm
and with a vertical offset of 224 mm.
If you place the projector in a different position (to that recommended), you will have to tilt
it down or up to center the image on the screen. In these situations, some image distortion
will occur. Use the Keystone function to correct the distortion. See "Correcting keystone" on
page 31 for details.
How to determine the recommended screen size for a
given distance
This method can be used for situations where you have purchased this projector and would
like to know what screen size will fit in your room.
The maximum screen size is limited by the physical space available in your room.
1.
2.
Measure the distance between the projector and where you want to position the
screen. This is the projection distance.
Refer to the table and find the closest match to your measurement in the average
available on the table, check that your measured distance is between the min and max
distances listed on either side of the average distance value.
3.
4.
Using this value, look across that row to the left to find the corresponding screen
diagonal listed in that row. That is the projected image size of the projector at that
projection distance.
offset in mm" value. This will determine the final placement of the screen in relation to
the horizontal plane of the projector.
For example, if your measured projection distance was 4.0 m (4000mm), the closest match
required.
Positioning your projector
17
Download from Www.Somanuals.com. All Manuals Search And Download.
W1060 projection dimensions
calculating the appropriate position.
Maximum zoom
Minimum zoom
Screen
Center of lens
Vertical offset
Projection distance
Recommended projection
distance from screen in mm
16:9 screen
Vertical
offset in
mm
diagonal
Width
mm
Height
mm
Min
Max
length
(with max.
zoom)
length
(with min
zoom)
Average
Inches
mm
27.6
40
604
526
296
498
-
-
999
1682
2103
2524
3365
4206
5047
6309
8412
9254
10516
-
44
1016
1270
1524
2032
2540
3048
3810
5080
5588
6350
7216
886
1408
1760
2112
2816
3520
4224
5280
7040
7744
8800
10000
1545
1932
2318
3090
3863
4636
5795
7726
8499
9658
-
75
50
1107
1328
1771
2214
2657
3321
4428
4870
5535
6289
623
93
60
747
112
149
187
224
280
374
411
467
531
80
996
100
120
150
200
220
250
284.1
1245
1494
1868
2491
2740
3113
3538
There is 5% tolerance among these numbers due to optical component variations. BenQ
recommends that if you intend to permanently install the projector, you should physically test
the projection size and distance using the actual projector before you permanently install it,
so as to make allowance for this projector's optical characteristics. This will help you
determine the exact mounting position so that it best suits your installation location.
18
Positioning your projector
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
When connecting a signal source to the projector, be sure to:
1.
2.
3.
Turn all equipment off before making any connections.
Use the correct signal cables for each source.
Ensure the cables are firmly inserted.
In the connections shown below, some cables may not be included with the projector (see
"Shipping contents" on page 8). They are commercially available from electronics stores.
Connecting a computer or monitor
Connecting a computer
The projector provides a VGA input socket that allows you to connect it to both IBM®
compatibles and Macintosh® computers. A Mac adapter (an optional accessory) is
needed if you are connecting legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
•
With a VGA cable:
•
With a HDMI cable:
Your computer must be
equipped with a HDMI output
socket.
1.
Take a VGA cable and connect one
end to the D-Sub output jack of the
computer. Connect the other end of
the VGA cable to the
PC signal input jack on the
projector.
1.
Take a HDMI cable and connect one
end to the HDMI jack of the
computer. Connect the other end of
the cable to the HMDI signal input
jack on the projector.
2.
If you wish to make use of the projector (mixed mono) speakers in your presentations,
take a suitable audio cable and connect one end of the cable to the audio output jack of
the computer, and the other end to the AUDIO jack of the projector. Once connected,
the audio can be controlled by the projector On-Screen Display (OSD) menus. See
"Audio Settings" on page 50 for details.
The final connection path should be like that shown in the following diagram:
Many notebooks do not
turn on their external
video ports when
connected to a
Notebook or desktop computer
projector. Usually a key
combo like FN + F3 or
CRT/LCD key turns the
external display on/off.
Locate a function key
labeled CRT/LCD or a
function key with a
monitor symbol on the
notebook. Press FN
and the labeled
1. HDMI cable
2. VGA cable
3. Audio cable
3
2
1
function key
simultaneously. Refer
to your notebook's
documentation to find
your notebook's key
combination.
COMPUTER
PC
COMPONENT
S-VIDEO
VIDEO
HDMI-1
HDMI-2
RS-232
USB
L
AUDIO
R
AUDIO
OUT
IN
Connections
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one of the
following output jacks:
•
•
•
•
HDMI
Component Video
S-Video
Video (composite)
You need only connect the projector to a Video source device using just one of the above
connecting methods, however each provides a different level of video quality. The method
you choose will most likely depend upon the availability of matching terminals on both the
projector and the Video source device as described below:
Best video quality
The best available video connection method is HDMI. If your source device is equipped
with a HDMI jack, you can enjoy uncompressed digital video quality.
HDMI source device and other details.
If no HDMI source is available, the next best video signal is Component Video (not to be
confused with composite Video). Digital TV tuners and DVD players output Component
Video natively, so if available on your devices, they should be your connection method of
choice in preference to S-Video or (composite) Video.
projector to a Component Video device.
Better video quality
The S-Video method provides a better quality analog video than standard composite Video.
If you have both composite Video and S-Video output terminals on your Video source
device, you should elect to use the S-Video option.
Least video quality
Composite Video is an analog video and will result in a perfectly acceptable, but less than
optimal result from your projector, being the least video quality of the available methods
described here.
S-Video or Video device.
Connecting Audio
The projector has a built-in mono speaker which is designed to provide basic audio
functionality accompanying data presentations for business purposes only. They are not
designed for, nor intended for stereo audio reproduction use as might be expected in home
theater or home cinema applications. Any stereo audio input (if provided), is mixed into a
common mono audio output through the projector speakers.
20
Connections
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting HDMI source devices
The projector provides a HDMI input jack that allows you to connect it to a HDMI source
device like a DVD player, a DTV tuner or a display.
HDMI (High-Definition Multimedia Interface) supports uncompressed video data
transmission between compatible devices like DTV tuners, DVD players and displays over a
single cable. It provides pure digital viewing and listening experience.
Examine your Video source device to determine if it has a set of unused HDMI output jacks
available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an HDMI source device:
1.
Take a HDMI cable and connect one end to the HDMI output jack of the HDMI
source device. Connect the other end of the cable to the HDMI signal input jack on the
projector. Once connected, the audio can be controlled by the projector On-Screen
The final connection path should be like that shown in the following diagram:
AV device
COMPUTER
COMPONENT
S-VIDEO
VIDEO
PC
HDMI-1
HDMI-2
RS-232
AUDIO
USB
L
AUDI
OUT
IN
HDMI
HDMI
HDMI cable
In the unlikely event that you connect the projector to a DVD player and the projected picture
displays wrong colors, please change the color space to a suitable selection (RGB/YUV). See
"Changing Color Space" on page 29 for details.
Connections
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Component Video source devices
Examine your Video source device to determine if it has a set of unused Component Video
output jacks available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:
1.
Take a Component Video cable and connect the end with 3 RCA type connectors to
the Component Video output jacks of the Video source device. Match the color of the
plugs to the color of the jacks; green to green, blue to blue, and red to red.
Connect the other end of the Component Video cable to the COMPONENT jack on
the projector. Match the colors of the plugs to the colors of the jacks-green to green,
blue to blue, and red to red.
2.
To connect the projector to an Audio source device:
1.
Take a suitable audio cable and connect one end to the audio L/R input of the AV
device. Connect the other end of the cable to the audio L/R input on the projector.
Once connected, the audio can be controlled by the projector On-Screen Display
The final connection path should be like that shown in the following diagram:
AV device
Component
video cable
Audio Cable
COMPUTER
PC
COMPONENT
S-VIDEO
VIDEO
DMI-1
HDMI-2
RS-232
USB
L
AUDIO
R
AUDIO
OUT
IN
•
•
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
If you have already made an HDMI Video connection between the projector and this
Component Video source device using HDMI Video connections, you need not connect to
this device using a Component Video connection as this makes an unnecessary second
connection of poorer picture quality. See "Connecting Video source devices" on page 20
for details.
22
Connections
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting S-Video source devices
Examine your Video source device to determine if it has an unused S-Video output socket
available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an S-Video source device:
1.
Take an S-Video cable and connect one end to the S-Video output socket of the Video
source device.
2.
Connect the other end of the S-Video cable to the S-VIDEO socket on the projector.
To connect the projector to an Audio source device:
1.
Take a suitable audio cable and connect one end to the AUDIO OUT jack of the AV
device. Connect the other end of the cable to the AUDIO IN jack on the projector.
Once connected, the audio can be controlled by the projector On-Screen Display
The final connection path should be like that shown in the following diagram:
S-Video Cable
AV device
COMPUTER
COMPONENT
S-VIDEO
VIDEO
PC
HDMI-1
HDMI-2
RS-232
AUDIO
USB
L
AUDIO
R
OUT
IN
Audio Cable
•
•
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
If you have already made a Component Video connection between the projector and this
S-Video source device using Component Video connections, you need not connect to this
device using an S-Video connection as this makes an unnecessary second connection of
Connections
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Composite Video source devices
Examine your Video source device to determine if it has a set of unused composite Video
output sockets available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a composite Video source device:
1.
Take a Video cable and connect one end to the composite Video output socket of the
Video source device.
2.
Connect the other end of the Video cable to the VIDEO socket on the projector.
To connect the projector to an Audio source device:
1.
Take a suitable audio cable and connect one end to the AUDIO OUT jack of the AV
device. Connect the other end of the cable to the AUDIO IN jack on the projector.
Once connected, the audio can be controlled by the projector On-Screen Display
The final connection path should be like that shown in the following diagram:
Video Cable
AV device
COMPUTER
COMPONENT
S-VIDEO
VIDEO
PC
HDMI-1
HDMI-2
RS-232
AUDIO
USB
L
AUDIO
R
OUT
IN
Audio Cable
•
•
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
You need only connect to this device using a composite Video connection if HDMI and
Component Video and S-Video inputs are unavailable for use. See "Connecting Video
source devices" on page 20 for details.
24
Connections
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Starting up the projector
1.
Plug the power cord into the projector and
into a wall socket. Turn on the wall socket
switch (where fitted). Check that the
POWER indicator light on the projector
lights orange after power has been applied.
Please use the original accessories (e.g. power
cable) only with the device to avoid possible
dangers such as electric shock and fire.
2.
Press POWER on the projector
or
remote control to start the projector
and a start up tone sounds. The POWER
indicator light flashes green and stays
green when the projector is on.
The start up procedure takes about 30
seconds. In the later stage of start up, a
startup logo is projected.
(If necessary) Rotate the focus ring to adjust the image clearness.
details.
If the projector is still hot from previous activity, it will run the cooling fan for approximately 90
seconds before energizing the lamp.
3.
To use the OSD menus, please set them to your familiar
language first. See "Personalizing the projector menu
display" on page 43 for details.
Please select language
4.
If you are prompted for a password, press the arrow keys
to enter a five digit password. See "Utilizing the password
function" on page 27 for details.
5.
6.
Switch all of the connected equipment on.
The projector will start to search for input signals. The
current input signal being scanned displays in the upper
left corner of the screen. If the projector doesn't detect a
Press Enter to confirm, Exit to leave
valid signal, the message 'No Signal' will continue displaying until an input signal is
found.
You can also press SOURCE on the projector or remote control to select your desired
If the frequency/resolution of the input signal exceeds the projector's operating range, you will
see the message 'Out of Range' displayed on a blank screen. Please change to an input signal
which is compatible with the projector's resolution or set the input signal to a lower setting.
To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before turning
if off.
Operation
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus
The projector is equipped with On-Screen Display (OSD) menus for making various
adjustments and settings.
Below is the overview of the OSD menu.
Main menu icon
PICTURE : Basic
Main menu
User 1
Picture Mode
Living Room
Reference Mode
Brightness
Contrast
50
0
Highlight
Sub-menu
Status
Color
0
0
Tint
Press MENU/
EXIT to the
previous
page or to
exit.
Sharpness
Flesh Tone
Save Settings
Reset Picture Settings
0
0
ENTER
Current input signal
To use the OSD menus, please set them to your familiar language first.
PC
Exit
Menu/Back
1.
Press MODE/ENTER on the projector or
remote control to turn the OSD menu on.
3.
Press
to highlight Language and
press MODE/ENTER to select a
preferred language.
PTCTURE : Basic
Picture Mode
Reference Mode
Brightness
Contrast
Color
Tint
Sharpness
Flesh Tone
Save Settings
User 1
Living Room
SYSTEM SETUP: Basic
Language
Projector Position
English
Front Table
50
0
Menu Settings
Operation Settings
Remote Receiver
Background Color
Splash Screen
0
0
Front+Top
Blue
BenQ
0
0
Reset Picture Settings
Menu/Back
PC
Exit
Menu/Back
Exit
PC
4.
to highlight the SYSTEM SETUP:
Basic menu.
Press MENU/EXIT twice* on the
projector or remote control to leave
and save the settings.
2.
Use
/
*The first press leads you back to
the main menu and the second
press closes the OSD menu.
SYSTEM SETUP: Basic
Language
English
Projector Position
Menu Settings
Front Table
Operating Settings
Remote Receiver
Background Color
Splash Screen
Front+Top
Blue
BenQ
Exit
Menu/Back
PC
Securing the projector
Using a security cable lock
The projector has to be installed in a safe place to prevent theft. Otherwise, purchase a lock,
such as a Kensington lock, to secure the projector. You can locate a Kensington lock slot on
A Kensington security cable lock is usually a combination of key(s) and a lock. Refer to the
lock’s documentation for finding out how to use it.
26
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an
option for setting up password security. The password can be set through the On-Screen
Display (OSD) menu. For details of the OSD menu operation, please refer to "Using the
You will be inconvenienced if you activate the power-on lock functionality and subsequently
forget the password. Print out this manual (if necessary) and write the password you used in
this manual, and keep the manual in a safe place for later recall.
Setting a password
Once a password has been set, the projector cannot be used unless the correct password is
entered every time the projector is started.
1.
Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security Settings
menu. Press MODE/ENTER. The Security Settings page displays.
2.
3.
Highlight Power on Lock and select On by pressing
As pictured to the right, the four arrow keys (
) respectively represent 4 digits (1, 2,
/
.
,
INPUT NEW PASSWORD
,
,
3, 4). According to the password you desire to set,
press the arrow keys to enter five digits for the
password.
4.
5.
Confirm the new password by re-entering the
new password.
Once the password is set, the OSD menu returns
to the Security Settings page.
MENU
Back
To activate the Power on Lock function, press
/
to highlight Power on Lock and
press
/
to select On.
The digits being input will display as asterisks on-screen. Write your selected password down
here in this manual in advance or right after the password is entered so that it is available to
you should you ever forget it.
Password: __ __ __ __ __
Keep this manual in a safe place.
6.
To leave the OSD menu, press MENU/EXIT.
If you forget the password
If the password function is activated, you will be asked
to enter the five-digit password every time you turn on
the projector. If you enter the wrong password, the
password error message as pictured to the right displays
lasting for three seconds, and the message 'INPUT
PASSWORD' follows. You can retry by entering another
five-digit password, or if you did not record the
Password Error
Please Try again.
password in this manual, and you absolutely do not remember it, you can use the password
If you enter an incorrect password 5 times in succession, the projector will automatically
shut down in a short time.
Operation
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Entering the password recall procedure
1.
Press and hold AUTO on the projector or remote
control for 3 seconds. The projector will display a
coded number on the screen.
RECALL PASSWORD
Please write down the recall code,
and contact BenQ
Customer Center.
2.
3.
Write down the number and turn off your
projector.
Seek help from the local BenQ service center to
decode the number. You may be required to
provide proof of purchase documentation to
verify that you are an authorized user of the
projector.
Recall code:
12345678
Back
MENU
Changing the password
1.
Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security Settings >
Change password menu.
2.
3.
Press MODE/ENTER. The message 'INPUT CURRENT PASSWORD' displays.
Enter the old password.
•
•
If the password is correct, another message 'INPUT NEW PASSWORD' displays.
If the password is incorrect, the password error message displays lasting for three
seconds, and the message 'INPUT CURRENT PASSWORD' displays for your retry.
You can press MENU/EXIT to cancel the change or try another password.
4.
Enter a new password.
The digits being input will display as asterisks on-screen. Write your selected password down
here in this manual in advance or right after the password is entered so that it is available to
you should you ever forget it.
Password: __ __ __ __ __
Keep this manual in a safe place.
5.
6.
Confirm the new password by re-entering the new password.
You have successfully assigned a new password to
the projector. Remember to enter the new
Password Changed
password next time the projector is started.
7.
To leave the OSD menu, press MENU/EXIT.
Disabling the password function
To disable password protection, go back to the SYSTEM SETUP: Advanced
Change Security Settings > Power on Lock menu after opening the OSD menu system. Select Off by
pressing . The message INPUT PASSWORD displays. Enter the current password.
>
Security Settings
>
/
'
'
i. If the password is correct, the OSD menu returns to the Security Settings page
with Off shown in the row of Power on Lock. You will not have to enter the
password next time you turn on the projector.
ii. If the password is incorrect, the password error message displays lasting for three
seconds, and the message 'INPUT PASSWORD' displays for your retry. You can
press MENU/EXIT to cancel the change or try another password.
Though the password function is disabled, you need to keep the old password in hand should
you ever need to re-activate the password function by entering the old password.
28
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can only
display one full screen at a time.
You can also manually cycle through the
available input signals.
1.
Press SOURCE on the projector or remote
control. A source selection bar displays.
2.
Press
/
until your desired signal is
selected and press MODE/ENTER.
Once detected, the selected source
information will display on the screen for
seconds. If there is multiple equipment
to search for another signal.
PC
HDMI 1
HDMI 2
•
•
The brightness level of the projected image
will change accordingly when you switch
between different input signals. Data (graphic)
"PC" presentations using mostly static
images are generally brighter than "Video"
using mostly moving images (movies).
COMPONENT
VIDEO
S-VIDEO
The native display resolution of this projector
is in a 16:9 aspect ratio. For best display
picture results, you should select and use an
input signal which outputs at this resolution. Any other resolutions will be scaled by the
projector depending upon the 'aspect ratio' setting, which may cause some image
Changing Color Space
In the unlikely event that you connect the projector to a DVD player via the projector’s
HDMI input and the projected picture displays wrong colors, please change the color space.
To do this:
1.
2.
Press MENU/EXIT and then press
/
until the DISPLAY menu is highlighted.
Press to highlight Color Space Conversion and press
/
to select the setting.
This function is only available when the HDMI input jack is in use.
Operation
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the projected image
Adjusting the projection angle
Remove the Back Foot Holder on the rear adjuster foot before adjusting the projection angle.
The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These
adjusters change the image height and projection angle. To adjust the projector:
1.
Press the quick-release button and lift the front
of the projector. Once the image is positioned
where you want it, release the quick-release
button to lock the foot in position.
2.
Rotate the rear adjuster foot to fine tune the
horizontal angle.
To retract the foot, hold up the projector while
pressing the quick-release button, then slowly
lower the projector. Screw the rear adjuster foot in
a reverse direction.
If the projector is not placed on a flat surface or the screen and the projector are not
perpendicular to each other, the projected image becomes trapezoidal. To correct this
•
Do not look into the lens while the lamp is on. The strong light from the lamp may cause
damage to your eyes.
•
Be careful when you press the adjuster button as it is close to the exhaust vent where hot
air comes from.
Auto-adjusting the image
In some cases, you may need to optimize the
picture quality. To do this, press AUTO on the
projector or remote control. Within 3 seconds,
the built-in Intelligent Auto Adjustment function
will re-adjust the values of Frequency and Clock
to provide the best picture quality.
The current source information will be displayed
in the upper left corner of the screen for 3
seconds.
•
•
The screen will be blank while AUTO is functioning.
This function is only available when PC signal (analog RGB) is selected.
30
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Fine-tuning the image size and clarity
1. Adjust the projected image to the size that 2. Then sharpen the image by rotating the
you need using the ZOOM ring.
FOCUS ring.
FOCUS
ZOOM
FOCUS
ZOOM
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either the
top or bottom. It occurs when the projector is not perpendicular to the screen.
To correct this, besides adjusting the height of the projector, and use Auto Keystone or
Keystone to manually correct it following one of these steps.
•
Using Auto Keystone
It can correct Keystone to optimal status by automatically.
•
Using the remote control
1.
2.
Press MENU/EXIT and then press
/
until the DISPLAY menu is highlighted.
Press to highlight Auto Keystone and press
Keystone function.
/
to select Off to disable Auto
3.
Press
control to display the Keystone correction
page. Press to correct keystoning at
the top of the image. Press to correct
/
on the projector or remote
keystoning at the bottom of the image.
Using the OSD menu
•
1.
Press MENU/EXIT and then press
/
until the DISPLAY menu is highlighted.
Press to highlight Auto Keystone and
2.
press
/
to select Off to disable Auto
Keystone function.
Press
/
.
Press
/
.
3.
4.
Press MENU/EXIT and then press
/
until the DISPLAY menu is highlighted.
Press to correct keystoning at the top of the
image or press to correct keystoning at the
bottom of the image.
Keystone
6
MENU Back
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Magnifying and searching for details
If you need to find the details on the projected picture, magnify the picture. Use the
direction arrow keys for navigating the picture.
1.
2.
3.
4.
Press MENU/EXIT and then press
/
until the DISPLAY menu is highlighted.
Press to highlight Digital Zoom and press MODE/ENTER. The Zoom bar displays.
Press on the projector repeatedly to magnify the picture to a desired size.
To navigate the picture, press MODE/ENTER to switch to the paning mode and press
the directional arrows (
,
,
,
) to navigate the picture.
5.
To reduce size of the picture, press MODE/ENTER to switch back to the zoom in/out
functionality, and press AUTO to restore the picture to its original size. You can also
press repeatedly until it is restored to the original size.
The picture can only be navigated after the picture is magnified. You can further magnify the
picture while searching for details.
Selecting Color Space Conversion
Highlight Color Space Conversion in the DISPLAY menu and select by pressing
the projector or remote control.
/
on
Select an appropriate color matrix type from among Auto/RGB/YUV.
This function is only available with HDMI input source.
Selecting the aspect ratio
The 'aspect ratio' is the ratio of the image width to the image height. For W1060, the default
aspect ration is 16:9. Most analog TV and computers are in 4:3 ratio, and digital TV and
DVDs are usually in 16:9 ratio.
With the advent of digital signal processing, digital display devices like this projector can
dynamically stretch and scale the image output to a different aspect than that of the image
input signal.
To change the projected image ratio (no matter what aspect the source is):
1.
2.
3.
Press MENU/EXIT and then press
Press to highlight Aspect Ratio.
/
until the DISPLAY menu is highlighted.
Press
/
to select an aspect ratio to suit the format of the video signal and your
display requirements.
32
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
About the aspect ratio
In the pictures below, the black portions are inactive areas and the white portions are active
areas. OSD menus can be displayed on those unused black areas.
1.
Auto:
Scales an image proportionally to fit the
projector’s native resolution in its
horizontal width and vertical height.
This is suitable for the incoming image
which is in 4:3 or 16:9 and you want to
make most use of the screen without
altering the image’s aspect ratio.
4:3 picture
16:9 picture
2. 16:9:
Scales an image so that it is displayed
in the center of the screen with a 16:9
aspect ratio. This is most suitable for
images which are already in a 16:9
aspect, like high definition TV, as it
displays them without aspect
alteration.
16:9 picture
3. 4:3:
Scales an image so that it is displayed
in the center of the screen with a 4:3
aspect ratio. This is most suitable for
4:3 images like computer monitors,
standard definition TV and 4:3 images
aspect DVD movies, as it displays
them without aspect alteration.
4:3 picture
4. Letter Box:
Scales an image so that the original
aspect ratio of the production is
preserved. For input signals that do
not conform to the projector's native
resolution, the full unaltered image is
displayed with a black border where
no image exists.
16:9 picture
Letter Box
format picture
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
33
5. Real:
The image is projected as its original
resolution, and resized to fit within the
display area. For input signals with lower
resolutions, the projected image will
display smaller than if resized to full
screen. You could adjust the zoom
setting or move the projector away from
the screen to increase the image size if
necessary. You may also need to refocus
the projector after making these
adjustments.
4:3 picture
OSD menus can be displayed in the
unused black areas.
34
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Optimizing the image
Selecting a picture mode
The projector is preset with several predefined picture
modes so that you can choose one to suit your operating
environment and input signal picture type.
To select an operation mode that suits your need, you
can follow one of the following steps.
•
Press MODE/ENTER on the projector repeatedly
until your desired mode is selected.
•
Go to the PICTURE: Basic > Picture Mode menu
and press
/
to select a desired mode.
The picture modes available for different types of signals are listed below.
1.
Bright mode: Maximizes the brightness of the projected image. This mode is suitable
for environments where extra-high brightness is required, such as using the projector
in well lit rooms.
2.
3.
4.
Living Room mode: Is designed for using the projector in a living room.
Gaming mode: Is designed for playing video games in a bright room.
Cinema mode: Is appropriate for playing colorful movies, video clips from digital
cameras or DVs through the PC input for best viewing in a blackened (little light)
environment.
5.
User 1/User 2/User 3 mode: Recalls the settings customized based on the current
details.
Setting the User 1/User 2/User 3 mode
There are three user-definable modes if the current available picture modes are not suitable
for your need. You can use one of the picture modes (except the User 1/User 2/User 3) as a
starting point and customize the settings.
1.
2.
3.
4.
Press MENU/EXIT to open the On-Screen Display (OSD) menu.
Go to the PICTURE: Basic > Picture Mode menu.
Press
Press
/
to select User 1 to User 2/User 3.
to highlight Reference Mode.
This function is only available when User 1/User 2/User 3 mode is selected up in the Picture
Mode sub-menu item.
5.
6.
Press
Press
/
to select a picture mode that is closest to your need.
to select a sub-menu item to be changed and adjust the value with
/
.
7.
8.
When all settings have been done, highlight Save Settings and press MODE/ENTER to
store the settings.
The confirmation message 'Setting Saved' displays.
Operation
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Fine-tuning the image quality in user modes
According to the detected signal type, there are some user-definable functions available
when User 1, User 2 or User 3 mode is selected. You can make adjustments to these
functions based on your needs.
Adjusting Brightness
Highlight Brightness in the PICTURE: Basic menu and adjust the values by pressing
on the projector or remote control.
/
The higher the value, the brighter the image. And lower
the setting, darker the image. Adjust this control so the
black areas of the image appear just as black and that
+50
+7
+30
detail in the dark areas is visible.
Adjusting Contrast
Highlight Contrast in the PICTURE: Basic menu and adjust the values by pressing
on the projector or remote control.
/
The higher the value, the greater the contrast. Use this
to set the peak white level after you have previously
adjusted the Brightness setting to suit your selected
0
-3
+30
input and viewing environment.
Adjusting Color
Highlight Color in the PICTURE: Basic menu and adjust the values by pressing
the projector or remote control.
/
on
Lower setting produces less saturated colors. If the setting is too high, colors on the image
will be overpowering, which makes the image unrealistic.
Adjusting Tint
Highlight Tint in the PICTURE: Basic menu and adjust the values by pressing
projector or remote control.
/
on the
The higher the value, the more reddish the picture becomes. The lower the value, the more
greenish the picture becomes.
Adjusting Sharpness
Highlight Sharpness in the PICTURE: Basic menu and adjust the values by pressing
/
on the projector or remote control.
The higher the value, the sharper the picture becomes. The lower the value, the softer the
picture becomes.
Adjusting Flesh Tone
Highlight Flesh Tone in the PICTURE: Basic menu and adjust the values by pressing
/
on the projector or remote control.
This function adjusts accurate color primaries resulting in natural looking flesh tones with
excellent color saturation.
36
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting Clarity Control
Highlight Clarity Control in the PICTURE: Advanced menu and adjust the values by
pressing MODE/ENTER on the projector or remote control.
To adjust the settings:
1.
Noise Reduction: Reduces electrical image noise caused by different media players.
The higher the setting, the less the noise.
Highlight Noise Reduction and press
/
to adjust the value from 0 to 15.
2.
Detail Enhancement: Sharpens the image. The higher the setting, the more details the
image reveals.
Highlight Detail Enhancement and press
enhance the image.
/
to adjust the value from 0 to 15 to
3.
4.
Luma Transmission (Luminance Transmission Improvement): Enhances picture brightness.
The higher the setting, the more distinct the effect.
Highlight Luma Transmission and press
/
to adjust the value from 0 to 10 to correct the
YCbCr color space and downsample the luminance components (Y) of the image.
Chroma Transmission (Chroma Transmission Improvement): Reduces color smear.
The higher the setting, the more distinct the effect.
Highlight Chroma Transmission and press
/
to adjust the value from 0 to 10 to
correct the YCbCr color space and downsample the chroma components (Cb and Cr)
of the image.
Selecting a Color Temperature
Highlight Color Temperature in the PICTURE: Advanced menu and adjust the values by
pressing
/
on the projector or remote control.
Choose a preferred color temperature from among Lamp Native/Warmer/Warm/Normal/
Cool/Cooler.
*About color temperatures:
There are many different shades that are considered to be "white" for various purposes. One
of the common methods of representing white color is known as the “color temperature”. A
white color with a low color temperature appears to be reddish white. A white color with a
high color temperature appears to have more blue in it.
Choose a preferred color temperature from among Lamp Native/Warmer /Warm /Normal /
Cool /Cooler (Warmer: 5000/ Warm: 6500/ Normal: 7300/ Cool: 8500/ Cooler: 9300).
•
•
The foregoing color temperature values are only for reference.
This function is only available when User 1/User 2/User 3 mode is selected up in the
Picture Mode sub-menu item.
Selecting a Color Temperature Fine Tuning
Highlight C.T. Control in the PICTURE: Advanced > Color Temperature Fine Tuning > C.T.
Control menu and adjust the values by pressing
/
on the projector or remote control.
Choose a preferred color temperature control range: R-Color: 5~195/ G-Color: 5~195/ B-
Color: 5~195.
Operation
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a White Balance
Highlight White Balance in the PICTURE: Advanced > Color Temperature Fine Tuning >
White Balance menu and adjust the values by pressing
control.
/
on the projector or remote
Choose a preferred white balance range: R-Gain: -50~50/ G-Gain : -50~50/ B-Gain: -50~50/
R-Bias: -50~50/ G-Bias: -50~50/ B-Bias: -50~50.
Selecting a Gamma Selection
Highlight Gamma Selection in the PICTURE: Advanced menu and select the modes by
pressing
/
on the projector or remote control.
Choose a preferred gamma mode from among 1.6/1.8/2.0/2.2/2.4/2.6/2.8.
Gamma Correction enables adjustment to the light intensity (brightness) of an image in
order to match the source more closely.
Adjusting Brilliant Color
Highlight Brilliant Color in the PICTURE: Advanced menu and select by pressing
/
on the projector or remote control.
This feature utilizes a new color-processing algorithm and system level enhancements to
enable higher brightness while providing truer, more vibrant colors in picture. It enables a
greater than 50% brightness increase in mid-tone images, which are common in video and
natural scenes, so the projector reproduces images in realistic and true colors. If you prefer
images with that quality, select On. If you don’t need it, select Off.
On is the default and recommended selection for this projector. When Off is selected, the
Color Temperature function is not available.
Selecting a White Peaking
Highlight White Peaking in the PICTURE: Advanced menu and adjust the values by
pressing
/
on the projector or remote control.
This adjustable item utilizes a new color-processing algorithm and system level
enhancements to enable higher brightness while providing true, more vibrant colors in
picture. The range is from 1 to 4. If you prefer a stronger enhanced image, adjust toward the
maximum setting. For a smoother, more natural image, adjust toward the minimum setting.
3D Color Management
In most installation situations, color management will not be necessary, such as in
classroom, meeting room, or lounge room situations where lights remain on, or where
building external windows allow daylight into the room.
Only in permanent installations with controlled lighting levels such as boardrooms, lecture
theaters, or home theaters, should color management be considered. Color management provides
fine color control adjustment to allow for more accurate color reproduction, should you require it.
Proper color management can only be achieved under controlled and reproducible viewing
conditions. You will need to use a colorimeter (color light meter), and provide a set of
suitable source images to measure color reproduction. These tools are not provided with the
projector, however, your projector supplier should be able to provide you with suitable
guidance, or even an experienced professional installer.
The Color Management provides six sets (RGBCMY) of colors to be adjusted. When you select
each color, you can independently adjust its range and saturation according to your preference.
If you have purchased a test disc which contains various color test patterns and can be used to
test the color presentation on monitors, TVs, projectors, etc. You can project any image from
the disc on the screen and enter the 3D Color Management menu to make adjustments.
38
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
To adjust the settings:
1.
2.
3.
Go to the PICTURE: Advanced menu and highlight 3D Color Management.
Press MODE/ENTER and the 3D Color Management page displays.
Highlight Primary color and press
Blue, Cyan, Magenta and Yellow.
/
to select a color from among Red, Green,
4.
Press
to highlight Hue and press
/
to select its range. Increase in the range
will include colors consisted of more proportions of its two adjacent colors.
Please refer to the illustration to the right for
how the colors relate to each other.
For example, if you select Red and set its
range at 0, only pure red in the projected
Yellow
GREEN
RED
picture will be selected. Increasing its range
will include red close to yellow and red close
to magenta.
Cyan
Magenta
5.
6.
Press
to highlight Saturation and adjust
its values to your preference by pressing
/
BLUE
. Every adjustment made will reflect to the
image immediately.
For example, if you select Red and set its
value at 0, only the saturation of pure red will be affected.
Press to highlight Gain and adjust its values to your preference by pressing
/
.
The contrast level of the primary color you select will be affected. Every adjustment
made will reflect to the image immediately.
7.
8.
9.
Repeat steps 3 to 6 for other color adjustments.
Make sure you have made all of the desired adjustments.
Press MENU/EXIT to exit and save the settings.
Saturation is the amount of that color in a video picture. Lower settings produce less
saturated colors; a setting of “0” removes that color from the image entirely. If the saturation
is too high, that color will be overpowering and unrealistic.
Selecting a Video Format
Highlight Video Format in the PICTURE: Advanced menu and select by pressing
the projector or remote control.
/
on
Select an appropriate video standard from among Auto/NTSC/NTSC3.58/NTSC4.43/PAL/
PAL-M/PAL-N/PAL60/SECAM.
In the normal condition, select Auto and the projector will automatically detect the video
standard. When the projector has difficulty detecting the video standard, select the
appropriate video standard from the menu.
This function is only available with Video and S-Video input source and must be configured
for Video and S-Video Connectors separately.
Operation
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a Film Mode
Highlight Film Mode in the PICTURE: Advanced menu and select by pressing
projector or remote control.
/
on the
On is the default and recommended selection for this projector. When Off is selected, the
Film Mode function is not available.
This function is only available when Video or S-Video with NTSC system is selected.
Selecting a 3D Comb Filter
Highlight 3D Comb Filter in the PICTURE: Advanced menu and select by pressing
/
on the projector or remote control.
3D Comb Filer separates the Y and C signals while simultaneously processing three
consecutive horizontal scan lines. While comparing three consecutive horizontal scan lines
within a single video frame, it also analyzes each frame in advance, ensuring the best
possible picture.
On is the default and recommended selection for this projector. When Off is selected, the 3D
Comb Filter function is not available.
This function is only available when Video is selected.
Hiding the image
In order to draw the audience's full attention
to the presenter, you can use BLANK on the
projector or remote control to hide the
screen image. Press any key on the projector
or remote control to restore the image. The
word 'BLANK' appears at the lower right
corner of the screen while the image is
hidden.
You can set the blank time in the SYSTEM
SETUP: Basic > Operation Settings >
Blank Timer menu to let the projector return the image automatically after a period of time
when there is no action taken on the blank screen.
No matter Blank Timer is activated or disabled, you can press any key except ENTER on the
remote control, or ENTER on the projector to restore the picture.
Do not block the projection lens from projecting as this could cause the blocking object to
become heated and deformed or even cause a fire.
Setting the Sleep Timer
You can set the Sleep Timer interval so the projector powers off after the specified time
period of inactivity (regardless of signal).
Set the sleep timer in the SYSTEM SETUP: Basic > Operation Settings > Sleep Timer
from among Disable/30 min/1 hr/2 hr/3 hr/4 hr/8 hr/ 12hr.
40
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Receiver
The Infrared Remote Receiver (Front and Top)
allows the projector to accept signals from the
remote control. For best results, be sure to aim
the control toward the sensor without any
obstructions between the two, and at a distance
no greater than 7 meters.
You can set the remote receiver in the SYSTEM
SETUP: Basic > Remote Receiver menu.
Freezing the image
Press FREEZE on the remote control to freeze the image. The word
'FREEZE' will display in the upper left corner of the screen. To release
the function, press any key on the projector or remote control.
Even if an image is frozen on the screen, the pictures are running on
the video or other device. If the connected devices have active audio
output, you will still hear the audio even though the image is frozen on
screen.
Operating in a high altitude environment
We recommend you use the High Altitude Mode when your environment is between
1500 m –3000 m above sea level, and temperature is between 5°C–23°C.
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and temperature
is between 5°C and 28°C. The projector will be over cooled, if you turn the mode on under
such a condition.
To activate the High Altitude Mode:
Notice
1.
2.
3.
Press MENU/EXIT and then press
until the SYSTEM SETUP: Advanced menu is
highlighted.
/
We recommend you use the High Altitude
mode by selecting it whenever your
environment is higher than 1500m.
Press
to highlight High Altitude Mode
to select On. A
Do you want to turn High Altitude
Mode ON?
and press
/
confirmation message displays.
Highlight Yes and press MODE/ENTER.
Yes
No
Operation under "High Altitude Mode" may cause
a higher decibel operating noise level because of increased fan speed necessary to improve
overall system cooling and performance.
If you use this projector under other extreme conditions excluding the above, it may display
auto shut-down symptoms, which is designed to protect your projector from over-heating.
In cases like this, you should switch to High Altitude mode to solve these symptoms.
However, this is not to state that this projector can operate under any and all harsh or
extreme conditions.
Operation
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the sound
The sound adjustments made as below will have an effect on the projector speakers. Be sure
you have made a correct connection to the projector audio input. See "Connections" on page
19 for how the audio input is connected.
INPUT SOUCER
PC
AUDIO IN
mini jack
AUDIO OUT
mini jack
mini jack
mini jack
mini jack
mini jack
HDMI 1/2
VIDEO
HDMI
RCA
S-VIDEO
RCA
COMPONENT
RCA
Muting the sound
To temporarily turn off the sound,
Using the remote control
Press MUTE to temporarily turn off the sound. While the sound is
off, the screen will display in the upper right corner of the screen.
•
To restore the sound, press MUTE again.
•
Using the OSD menu
1.
Press MENU/EXIT and then press
/
until the SYSTEM
SETUP: Advanced menu is highlighted.
Press to highlight Audio Settings and press ENTER.
The Audio Settings page displays.
Highlight Mute and press
To restore the sound, repeat steps 1-3 and press
2.
3.
4.
/
to select On.
/
to select Off.
Adjusting the sound level
To adjust the sound level,
•
Using the remote control
Press or to select a desired sound level.
•
Using the OSD menu
Press MENU/EXIT and then press
is highlighted.
1.
/
until the SYSTEM SETUP: Advanced menu
2.
Press
to highlight Audio Settings and press ENTER. The Audio Settings page displays.
to highlight Volume and press to select a desired sound level.
3.
Press
/
Turning off the Power on/off Ring Tone
1.
Repeat steps 1-2 above.
2.
Press to highlight Power on/off ring tone and press
/
to select Off.
The only way to change Power on/off ring tone is setting On or Off here. Setting the sound
mute or changing the sound level will not affect the Power on/off ring tone.
42
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Personalizing the projector menu display
The On-Screen Display (OSD) menus can be set according to your preferences. The
following settings do not affect the projection settings, operation, or performance.
•
Menu display time in the SYSTEM SETUP: Basic > Menu Settings menu sets the length
of time the OSD will remain active after your last key press. The time length ranges from
5 to 30 seconds in 5-second increments. Use
Menu position in the SYSTEM SETUP: Basic > Menu Settings menu sets the OSD
position in five locations. Use to select a preferred position.
Language in the SYSTEM SETUP: Basic menu sets your familiar language for the OSD
menus. Use to select your language.
Splash Screen in the SYSTEM SETUP: Basic menu sets a preferred logo screen to be
displayed during projector start-up. Use to select a screen.
/
to select a suitable time frame.
•
•
•
/
/
/
Shutting down the projector
1.
To turn the projector off, press POWER
OFF on the remote control to turn the
projector off directly. Or you can press
POWER on the projector and a
warning message appears. Press
POWER again.
2.
3.
Once the cooling process finishes, the
POWER indicator light is a steady
orange and fans stop.
Disconnect the power cord from the wall
socket if the projector will not be used in
an extended period of time.
•
•
To protect the lamp, the projector will not
respond to any commands during the
cooling process.
If the projector is not properly shut down,
to protect the lamp, when you attempt to re-
start the projector, the fans will run for a few minutes to cool down. Press POWER again to
start the projector after the fans stop and the POWER indicator light turns orange.
•
Lamp life results will vary depending on environmental conditions, and usage.
Operation
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type
selected.
Main menu Sub-menu
Picture Mode
Options
Bright/Living Room/Gaming/Cinema//User 1/User 2/
User 3
Reference Mode
Brightness
Bright/Living Room/Gaming/Cinema
Contrast
1.
Color
PICTURE:
Tint
Basic
Sharpness
Flesh Tone
Save Settings
Reset Picture
Settings
Noise Reduction/Detail
Clarity Control
Enhancement/Luma Transmission/
Chroma Transmission
Gamma Selection
Brilliant Color
1.6/1.8/2.0/2.2/2.4/2.6/2.8
On/Off
White Peaking
Primary Color
Hue
R/G/B/Y/C/M
3D Color
Management
2.
Saturation
Gain
PICTURE:
Advanced
Lamp Native/Warmer/Warm/
Normal/Cool/Cooler
Color Temperature
C.T. Control
R-Color/G-Color/B-Color
Color Temperature
Fine Tuning
R-Gain/G-Gain/B-Gain/R-Bias/
G-Bias/B-Bias
White Balance
Auto/NTSC/NTSC3.58/NTSC4.43/
PAL/PAL-M/PAL-N/PAL60/SECAM
Video Format
Film Mode
On/Off
On/Off
3D Comb Filter
44
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Aspect Ratio
Keystone
Auto/16:9/4:3/Letter Box/Real
On/Off
Auto Keystone
Keystone
Overscan
Adjustment
3.
Digital Zoom
DISPLAY
Auto/H. Size/Phase/Horizontal
position/Vertical position/SOG
Level
PC & Component
YPbPr Tuning
Color Space
Conversion
Auto/RGB/YUV
Language
Front Table/Rear Table/
Rear Ceiling/Front Ceiling
Projector Position
5 sec/10 sec/15 sec/20 sec/25 sec/
30 sec
Menu Display Time
Menu position
Top-Left/Top-Right/Center/
Bottom-Left/Bottom-Right
Menu Settings
4.
Reminder
Message
SYSTEM
SETUP:
Basic
On/Off
Direct Power On On/Off
Disable/5 min/10 min/15 min/20
min/25 min/30 min
Auto Power Off
Quick Cooling
Blank Timer
On/Off
Operation Settings
Disable/5 min/10 min/15 min/20
min/25 min/30 min
Disable/30 min/1 hr/2 hr/3 hr/4 hr/8
hr/12 hr
Sleep Timer
Remote Receiver
Background Color
Splash Screen
Front+Top/ Front/ Top
Purple/Black/Blue
BenQ/Blue/Black
Operation
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Settings
Mute
Off/On
Volume
Range : 0 ~ 10
Power on/off
ring tone
Off/On
Lamp Mode
Normal/Economic
Lamp Settings
HDMI Settings
Reset lamp timer
Equivalent Lamp Hour
HDMI Format
Auto/PC Signal/Video Signal
HDMI Amplifier
Gain
Range:1 ~ 3
5.
SYSTEM
SETUP:
Advanced
High Altitude Mode Off/On
Change password
Security Settings
Change Security
Settings
Power on Lock
2400/4800/9600/14400/19200/
38400/57600/115200
Baud Rate
Test Pattern
Off/On
Closed Caption
Enable
Off/On
Closed Caption
Caption Version
CC1/CC2/CC3/CC4
Off/On
LED Indicator
Reset All Settings
• Source
• Picture Mode
• Resolution
• Color System
• Equivalent Lamp Hour
• Firmware Version
6.
Current System Status
INFORMA-
TION
Note that the menu items are available when the projector detects at least one valid signal. If
there is no equipment connected to the projector or no signal detected, limited menu items
are accessible.
46
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of each menu
FUNCTION
DESCRIPTION
Pre-defined picture modes are provided so you can optimize your
projector image set-up to suit your program type. See "Selecting a
picture mode" on page 35 for details.
Picture Mode
Selects a picture mode that most suits your need for the image quality
and further fine-tune the image based on the selections listed on the
same page below.
Reference
Mode
Adjusts the brightness of the image. See "Adjusting Brightness" on
page 36 for details.
Brightness
Contrast
Adjusts the degree of difference between dark and light in the image.
Adjusts the color saturation level -- the amount of each color in a
Color
This function is only available when Video or S-Video with NTSC
system is selected.
Adjusts the red and green color tones of the image. See "Adjusting
Tint" on page 36 for details.
Tint
This function is only available when Video or S-Video with NTSC
system is selected.
Adjusts the image to make it look sharper or softer. See "Adjusting
Sharpness" on page 36 for details.
Sharpness
This function is only available when Video or S-Video with NTSC
system is selected.
Flesh Tone
Saves the settings made for User 1 or User 2 or User 3 mode.
Save Settings
Reset Picture
Settings
Resets the picture settings for User 1 or User 2 or User 3 mode.
Operation
47
Download from Www.Somanuals.com. All Manuals Search And Download.
FUNCTION
DESCRIPTION
Clarity Control
Gamma
Selection
Selects gamma mode that most suits your need for the image quality.
Adjusts the Brilliant Color value to extend the exposure range and
sharpens detail for grain free images.
Brilliant Color
White
Peaking
Adjusts white peaking while maintaining correct color presentation.
3D Color
Management
Color
Temperature
•
•
C.T. Control
details.
White Balance
Color
Temperature
Fine Tuning
Selects the default video format to use for Video or S-Video input.
Video Format
Film Mode
This function is only available when Video or S-Video with NTSC
system is selected.
This function is only available when Video or S-Video with NTSC
system is selected.
3D Comb
Filter
This function is only available when Video is selected.
There are five options to set the image's aspect ratio depending on your
Aspect Ratio
Keystone
Corrects any keystoning of the image automatically or manually.
Overscan
Adjustment
Removes the noise in a video image. Overscans the image to remove
video encoding noise on the edge of video source.
Magnifies or reduces the projected image.
Digital Zoom
PC &
Component
YPbPr Tuning
Corrects the display data frequency, phase, the position of the image
and selects the preferred SOG level automatically or manually.
Color Space
Conversion
Only action for HDMI Input source.
48
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
FUNCTION
Language
DESCRIPTION
Sets the language for the On-Screen Display (OSD) menus.
The projector can be installed on a ceiling or behind a screen, or with
one or more mirrors.
Projector
Position
Menu display time
Sets the length of time the OSD will remain active after your last key
press. The range is from 5 to 30 seconds in 5-second increments.
Menu
Settings
Menu position
Sets the On-Screen Display (OSD) menu position.
Reminder Message
Selecting On allows the projector to remind you to clean the filter.
Direct Power On
Powers projector on automatically when the power cable is connected.
Auto Power Off
Allows the projector to turn off automatically if no input signal is
detected after a set period of time.
Quick Cooling
Enables or disables the Quick Cooling function.
Selecting On enables the function and the projector cooling time will
be shortened from a normal 90 second duration to approximately 2
seconds.
Operation
Settings
Blank Timer
Sets the image blank time when the Blank feature is activated, once
elapsed the image will return to the screen.
Sleep Timer
Sets the auto-shutdown timer. The timer can be set to a value between
30 minutes and 12 hours.
Remote
Receiver
Sets the preferred remote receiver (Front and Top) allowing the
projector to accept signals from the remote control.
Background
Color
Selects background appearance when there is no signal.
Allows you to select which logo screen will display during projector
start-up. Four options are available: BenQ logo, Blue screen, or Black
screen.
Splash
Screen
Operation
49
Download from Www.Somanuals.com. All Manuals Search And Download.
FUNCTION
DESCRIPTION
Mute
Audio
Volume
Power On/Off Ring Tone
Settings
Lamp Mode
Reset Lamp Timer
Lamp
Settings
Equivalent Lamp Hour
the total lamp hour is calculated.
HDMI Format
Selects appropriate HDMI format automatically or manually.
HDMI Amplifier Gain
HDMI
Settings
Adjusts the appropriate HDMI amplifier gain automatically or manually.
High Altitude
Mode
A mode for operation in high altitude areas.
Change password
You will be asked to enter the current password before changing to a
Security
Settings
Change Security Settings
Power on Lock
When Power On Lock is activated, you will be asked to enter the
current password before powering on the projector.
Selects a baud rate that is identical with your computer’s so that you
can connect the projector using a suitable RS-232 cable and update or
download the projector’s firmware. This function is intended for
qualified service personnel.
Baud Rate
Selecting On enables the function and the projector displays the grid
test pattern. It helps you adjust the image size and focus and check that
the projected image is free from distortion.
Test Pattern
Selects the screen to display closed captioning text if available.
Closed Caption
LED Indicator
Selecting On enables the function and the POWER LED on the
control panel lights when the project is in use.
Returns all settings to the factory preset values.
Reset All
Settings
The following settings will still remain: PC & Component YPbPr
Tuning, Language, Projector Position, High Altitude Mode,
Security Setting and Baud Rate.
50
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
FUNCTION
DESCRIPTION
Source
Shows the current signal source.
Picture Mode
Shows the selected mode in the PICTURE menu.
Resolution
Current
System
Status
Shows the native resolution of the input signal.
Color System
Shows input system format, NTSC, PAL, SECAM, or RGB.
Equivalent Lamp Hour
Displays the number of hours the lamp has been used.
Firmware Version
Displays the firmware version of the projector.
The INFORMATION menu shows you the current operating status of the projector.
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
51
Maintenance
Care of the projector
Your projector needs little maintenance. The only thing you need to do on a regular basis is
to keep the lens clean.
Never remove any parts of the projector except the lamp. Contact your dealer if other parts
need replacing.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface.
•
•
Use a canister of compressed air to remove dust.
If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens cleaner
and gently wipe the lens surface.
Never use any type of abrasive pad, alkaline/acid cleaner, scouring powder, or volatile solvent,
such as alcohol, benzene, thinner or insecticide. Using such materials or maintaining
prolonged contact with rubber or vinyl materials may result in damage to the projector surface
and cabinet material.
Cleaning the projector case
Before you clean the case, turn the projector off using the proper shutdown procedure as
•
•
To remove dirt or dust, wipe the case with a soft, lint-free cloth.
To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH
detergent. Then wipe the case.
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the
case.
Storing the projector
If you need to store the projector for an extended time, please follow the instructions below:
•
Make sure the temperature and humidity of the storage area are within the
consult your dealer about the range.
•
•
•
Retract the adjuster feet.
Remove the battery from the remote control.
Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent.
When you carry the projector yourself, please use the original box or a suitable soft carry
case.
52
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamp information
Getting to know the lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is automatically
calculated by the built-in timer. The method of calculating the equivalent lamp hour is as
follows:
To obtain the lamp hour information:
1.
Press Menu/Exit and then press
highlighted.
/
until the SYSTEM SETUP: Advanced menu is
2.
Press to highlight Lamp Settings and press MODE/ENTER. The Lamp Settings page
displays.
3.
4.
You will see the Equivalent lamp hour information displaying on the menu.
To leave the menu, press Menu/Exit.
You can also get the lamp hour information on the INFORMATION menu.
Extending lamp life
The projection lamp is a consumable item . To keep the lamp life as long as possible, you can
do the following settings via the OSD menu.
Setting Lamp mode as Economic
Using Economic mode reduces system noise and power consumption by 20%. If the
Economic mode is selected, the light output will be reduced and result in darker projected
pictures.
Setting the projector in Economic mode also extends the lamp operation life. To set
Economic mode, go into the SYSTEM SETUP: Advanced > Lamp Settings > Lamp mode
menu and press
/
.
Setting Auto Power Off
This function allows the projector to turn off automatically if no input source is detected
after a set period of time to prevent unnecessary waste of lamp life.
To set Auto Power Off, go into the SYSTEM SETUP: Basic > Operating Settings > Auto
Power Off menu and press
/
. The time period can be set from 5 to 30 minutes in 5-
minute increments. If the preset time lengths are not suitable for your presentation, select
Disable. The projector will not automatically shut down in a certain time period.
Maintenance
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Timing of replacing the lamp
When the Lamp indicator lights up red or a message appears suggesting it is time to replace
the lamp, please install a new lamp or consult your dealer. An old lamp may cause a
malfunction in the projector and in some instances the lamp may explode.
The Lamp indicator light and Temperature warning light will light up if the lamp becomes too
The warning messages below are for reference only. Please follow the actual on-screen
instructions to prepare and replace the lamp.
Status
Message
Install a new lamp for optimal performance. If the
projector is normally run with Economic selected
53), you may continue to operate the projector
until the next lamp warning appears.
Notice
Order Replacement Lamp
Lamp > XXXX Hours
Order a new lamp at lamp.benq.com
OK
A new lamp should be fitted to avoid the
inconvenience when the projector runs out of
lamp time.
Notice
Replace Lamp soon
Lamp > XXXX Hours
Order a new lamp at lamp.benq.com
OK
It is strongly recommended that you replace the
lamp at this stage. The lamp is a consumable item.
The lamp brightness diminishes with use. This is
normal lamp behavior. You can replace the lamp
whenever you notice that the brightness level has
significantly diminished.
Notice
Replace Lamp Now
Lamp > XXXX Hours
Lamp usage time exceeded
Order a new lamp at lamp.benq.com
OK
The lamp MUST be replaced before the projector
will operate normally.
Notice
Out of Lamp Usage Time
Replace lamp (Refer to user manual)
Then reset lamp timer
Order a new lamp at lamp.benq.com
OK
“XXXX” shown in the above messages are numbers that vary depending on different models.
54
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the lamp
•
If lamp replacement is performed while the projector is suspended upside-down from the
ceiling, make sure that no one is underneath the lamp socket to avoid any possible injury
or damage to the human eyes caused by fractured lamp.
•
•
•
•
•
•
•
To reduce the risk of electrical shock, always turn the projector off and disconnect the
power cord before changing the lamp.
To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes
before replacing the lamp.
To reduce the risk of injuries to fingers and damage to internal components, use caution
when removing lamp glass that has shattered into sharp pieces.
To reduce the risk of injuries to fingers and/or compromising image quality by touching
the lens, do not touch the empty lamp compartment when the lamp is removed.
This lamp contains mercury. Consult your local hazardous waste regulations to dispose of
this lamp in a proper manner.
To assure optimal performance from the projector, it is recommended that you purchase a
BenQ projector lamp for lamp replacement.
If lamp replacement is performed while the projector is suspended upside-down from the
ceiling, make sure that no one is underneath the lamp socket to avoid any possible injury
or damage to the human eyes caused by fractured lamp.
1.
Turn the power off and disconnect the projector from the wall socket. If the lamp is
hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled.
Loosen the captive screw from the front.
2.
3.
Remove the lamp compartment cover
as shown.
4.
•
Loosen the three captive screws that
secure the lamp.
Do not turn the power on with the lamp
cover removed.
•
Do not insert your fingers between the
lamp and the projector. The sharp edges
inside the projector may cause injuries.
Maintenance
55
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
Lift the handle so that it stands up. Use
the handle to slowly pull the lamp out
of the projector.
•
•
•
Pulling it too quickly may cause the lamp
to break and scatter broken glass in the
projector.
Do not place the lamp in locations where
water might splash on it, children can
reach it, or near flammable materials.
Do not insert your hands into the projector
after the lamp is removed. If you touch the
optical components inside, it could cause
color unevenness and distortion of the
projected images.
6.
Insert the new lamp into the lamp
compartment and make sure it fits in
the projector.
Ensure the connectors are aligned.
If you experience resistance, lift the lamp and
start again.
7.
Tighten the screws that secure the lamp.
•
Loose screw may cause a bad connection,
which could result in malfunction.
•
Do not over tighten the screw.
8.
Ensure the handle is fully laid flat and
locked in place.
9.
Replace the lamp compartment cover
on the projector and tighten the captive
screw.
10. Restart the projector.
Do not turn the power on with the lamp cover removed.
56
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
Resetting the lamp timer
11. After the startup logo, open the On-Screen
Display (OSD) menu. Go to the SYSTEM
SETUP: Advanced > Lamp Settings menu.
Press MODE/ENTER. The Lamp Settings
page displays. Press to highlight Reset
lamp timer and press MODE/ENTER. A
warning message displays asking if you
Notice
Reset Lamp Timer?
Reset
No
want to reset the lamp timer. Highlight Reset and press MODE/ENTER. The lamp
time will be reset to '0'.
Do not reset if the lamp is not new or replaced as this could cause damage.
Maintenance
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Indicators
Light
Status & Description
Power Temp
Power events
Lamp
Orange
Off
Off
Off
Off
Off
Off
Off
Off
Stand-by mode
Powering up
Green
Flashing
Green
Normal operation
Orange
Flashing
The projector needs to cool for 90 seconds after the power is
turned off.
Lamp events
Orange
Off
Red
Red
The lamp ignition retries if the lamp fails during startup.
Flashing
1.
2.
The projector needs 90 seconds to cool down. Or
Please contact your dealer for assistance.
Off
Off
Thermal events
Off
Off
Red
Red
Red
Red
Red
Red
Red
Red
Red
Off
Red
Off
Green
Orange
Red
Off
The projector has shutdown automatically. If you try to re-
start the projector, it will shutdown again. Please contact your
dealer for assistance.
Red
Red
Red
Green
Green
Green
Orange
Red
Green
System events
Off
Off
Off
Green
Green
Red
The projector has shutdown automatically. If you try to re-
start the projector, it will shutdown again. Please contact your
dealer for assistance.
Green
Green Orange
58
Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
The projector does not turn on.
Cause
Remedy
Plug the power cord into the AC inlet on the
projector, and plug the power cord into the
power outlet. If the power outlet has a switch,
make sure that it is switched on.
There is no power from the power
cable.
Attempting to turn the projector on
again during the cooling process.
Wait until the cooling down process has
completed.
No picture
Cause
Remedy
The video source is not turned on or
connected correctly.
Turn the video source on and check that the
signal cable is connected correctly.
The projector is not correctly
connected to the input signal device.
Check the connection.
Select the correct input signal with the
SOURCE key on the projector or remote
control.
The input signal has not been
correctly selected.
Blurred image
Cause
Remedy
The projection lens is not correctly
focused.
Adjust the focus of the lens using the focus
ring.
The projector and the screen are not
aligned properly.
Adjust the projection angle and direction as
well as the height of the unit if necessary.
Remote control does not work
Cause
Remedy
The battery is out of power.
Replace the battery with new one.
There is an obstacle between the
remote control and the projector.
Remove the obstacle.
You are too far away from the
projector.
Stand within 7 meters (23 feet) of the
projector.
The password is incorrect
Cause
Remedy
Please see "Entering the password recall
procedure" on page 28 for details.
You do not remember the password.
Troubleshooting
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Projector specifications
All specifications are subject to change without notice.
General
Product name
Model name
Digital Projector
W1060
Optical
Resolution
Display system
Lens F/Number
Lamp
1920 x 1080, 1080p
1-CHIP DMD
F = 2.5 to 2.76, f = 23.5 to 28.2mm
190 W lamp
Electrical
Power supply
AC100–240V, 50/60 Hz (Automatic)
250W (Max)/
<1W (Standby)
Power consumption
Mechanical
Dimensions
Weight
330 mm (W) x 150 mm (H) x 247 mm (D) (Adjust foot max.)
8 lbs (3.63 Kg)
Input terminal
Computer input
RGB input
D-Sub 15-pin (female) x 1
Video signal input
QvmbÓ> x 2
HDMI
S-VIDEO
VIDEO
Mini DIN 4-pin port x 1
RCA jack x 1
SD/HDTV signal input
Audio input
Component RCA jack x 3
Mini jack x 1, RCA jack x 2
Output terminal
Audio output
Speaker
Mini jack x 1
10W mono speaker
Control terminal
USB
Type B
RS-232 serial control
9 pin x 1
Environmental Requirements
Operating temperature
5°C–35°C at sea level
Operating relative humidity 10%–85% (without condensation)
•
•
0–1499 m at 5°C–28°C
1500–3000 m at 5°C–23°C (with High Altitude Mode on)
Operating altitude
60
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
Timing chart
Supported timing for PC input
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel
Frequency
(MHz)
Mode
31.469
59.940
25.175
VGA_60
37.861
37.500
43.269
37.927
35.2
72.809
75.000
85.008
85.039
56.3
31.500
31.500
36.000
35.5
VGA_72
640 x 480
VGA_75
VGA_85
720 x 400
800 x 600
720 x 400 x 85
SVGA_56
SVGA_60
SVGA_72
SVGA_75
SVGA_85
XGA_60
36
37.879
48.077
46.875
53.674
48.363
56.476
60.023
68.667
49.7
60.317
72.188
75.000
85.061
60.004
70.069
75.029
84.997
59.8
40.000
50.000
49.500
56.250
65.000
75.000
78.750
94.500
83.5
XGA_70
1024 x 768
XGA_75
XGA_85
WXGA_60
WXGA_75
WXGA_85
SXGA3_60
SXGA3_75
SXGA3_85
WXGA+_60
SXGA+_60
UXGA
1280 x 800
62.8
74.9
106.5
71.554
63.981
79.976
91.146
55.935
65.317
75.000
84.880
60.020
75.025
85.024
59.887
59.978
60.000
122.500
108.000
135.000
157.500
106.500
121.750
162.000
1280 x 1024
1440 x 900
1400 x 1050
1600 x 1200
62
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel
Frequency
(MHz)
Mode
640 x 480@67Hz
832 x 624@75Hz
1024 x 768@75Hz
1152 x 870@75Hz
35.000
66.667
30.240
MAC13
49.722
60.240
68.68
74.546
75.020
75.06
57.280
80.000
100.000
MAC16
MAC19
MAC21
1024 x
576-GTF
1024 x 576@60Hz
1024 x 600@60Hz
35.82
37.32
60
60
46.996
48.964
1024 x
600-GTF
Supported timing for Component-YPbPr input
Signal Format
480i(525i)@60Hz
Horizontal Frequency (kHz)
Vertical Frequency (Hz)
59.94
15.73
31.47
15.63
31.25
45.00
37.50
33.75
28.13
67.5
480p(525p)@60Hz
576i(625i)@50Hz
576p(625p)@50Hz
720p(750p)@60Hz
720p(750p)@50Hz
1080i(1125i)@60Hz
1080i(1125i)@50Hz
1080P@60Hz
59.94
50.00
50.00
60.00
50.00
60.00
50.00
60.00
50.00
24
1080P@50Hz
56.26
27
1080P@24Hz
1080P@25Hz
28.12
33.75
25
1080P@30Hz
30
•
Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image
vibration.
Specifications
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Supported timing for Video and S-Video inputs
Video mode
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Color sub-carrier
Frequency
(MHz)
NTSC
15.73
60
50
50
60
50
60
60
3.58
4.43
PAL
15.63
15.63
15.73
15.63
15.73
15.73
SECAM
PAL-M
PAL-N
PAL-60
NTSC4.43
4.25 or 4.41
3.58
3.58
4.43
4.43
Supported timing for HDMI (HDCP) input
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel
Frequency
(MHz)
Mode
720 x 400
640 x 480
37.927
85.039
35.5
720 x 400_85
VGA_60
VGA_72
VGA_75
VGA_85
SVGA_56
SVGA_60
SVGA_72
SVGA_75
SVGA_85
XGA_60
XGA_70
XGA_75
XGA_85
31.469
37.861
37.500
43.269
35.2
59.940
72.809
75.000
85.008
56.3
25.175
31.500
31.500
36.000
36
37.879
48.077
46.875
53.674
48.363
56.476
60.023
68.667
60.317
72.188
75.000
85.061
60.004
70.069
75.029
84.997
40.000
50.000
49.500
56.250
65.000
75.000
78.750
94.500
800 x 600
1024 x 768
64
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel
Frequency
(MHz)
Mode
49.7
59.8
83.5
WXGA_60
WXGA_75
WXGA_85
SXGA_60
SXGA_75
SXGA_85
WXGA+_60
SXGA+_60
UXGA
1280 x 800
62.8
74.9
84.880
60.020
75.025
85.024
59.887
59.978
60.000
66.667
74.546
75.020
75.06
60
106.5
71.554
63.981
79.976
91.146
55.935
65.317
75.000
35.000
49.722
60.241
68.68
31.47
31.25
37.50
45.00
28.13
33.75
67.5
122.500
108.000
135.000
157.500
106.500
121.750
162.000
30.240
57.280
80.000
100.000
27
1280 x 1024
1440 x 900
1400 x 1050
1600 x 1200
640 x 480@67Hz
832 x 624@75Hz
1024 x 768@75Hz
1152 x 870@75Hz
MAC13
MAC16
MAC19
MAC21
480p
50
27.000
74.25
576p
50
720p_50
720p_60
1080i_50
1080i_60
1080p
60
74.25
VIDEO
50
74.25
60
74.25
60
148.5
56.26
27
50
148.5
1080p
1080P@24Hz
1080P@25Hz
1080P@30Hz
24
74.25
1080P@24Hz
1080P@25Hz
1080P@30Hz
28.12
33.75
25
74.25
30
74.25
Displaying a 1080i_50 or 1080i_60 signal may result in slight image vibration.
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
65
Warranty and Copyright information
Limited warranty
BenQ warrants this product against any defects in material and workmanship, under normal
usage and storage.
Proof of purchase date will be required with any warranty claim. In the event this product is
found to be defective within the warranty period, BenQ's only obligation and your exclusive
remedy shall be replacement of any defective parts (labor included). To obtain warranty
service, immediately notify the dealer from which you purchased the product of any defects.
Important: The above warranty shall be void if the customer fails to operate the product in
accordance with BenQ's written instructions, especially the ambient humidity must be in-
between 10% and 85%, temperature in-between 5°C and 28°C, altitude lower than 4920
feet, and avoiding to operate the projector in a dusty environment. This warranty gives you
specific legal rights, and you may have other rights which vary from country to country.
Copyright
Copyright 2011 by BenQ Corporation. All rights reserved. No part of this publication may
be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any
language or computer language, in any form or by any means, electronic, mechanical,
magnetic, optical, chemical, manual or otherwise, without the prior written permission of
BenQ Corporation.
Disclaimer
BenQ Corporation makes no representations or warranties, either expressed or implied,
with respect to the contents hereof and specifically disclaims any warranties, merchantability
or fitness for any particular purpose. Further, BenQ Corporation reserves the right to revise
this publication and to make changes from time to time in the contents hereof without
obligation to notify any person of such revision or changes.
*DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments. Others
are copyrights of their respective companies or organizations.
66
Warranty and Copyright information
Download from Www.Somanuals.com. All Manuals Search And Download.
|