P73240_F5F315-T_US_man.qxd 9/24/03 3:21 PM Page 1
F4F315-T
Us e r Ma nua l
F4F315-T
P73240
Download from Www.Somanuals.com. All Manuals Search And Download.
P73240_F5F315-T_US_man.qxd 9/24/03 3:21 PM Page 1
To Test Straight Twisted Pair
(Shielded or Unshielded) Cables
1. Plug one end of the cable into the modular jack on the
master unit and the other end into the modular jack of
the remote terminator.
2. As soon as the Power is turned on, the LEDs on the
remote terminator will start to scan each pair one by one.
If the cable wiring is intact, the LEDs corresponding to
each pair will illuminate green. If the LEDs illuminate
green first and red afterwards or do not illuminate, the
cable wiring is bad.
3. Straight-through vs. Crossover: If the LED lights up from
top to bottom (1&2, 3&6, 4&5, 7&8), the cable is wired in
a straight-through configuration. If the pairs are crossed,
the LED will not light up from top to bottom; it will light
up in a different order depending on how the pairs
are crossed.
4. For RJ45 cables that have only 2 pairs (4 conductors)
wired please refer to the LED guide printed on the
remote terminator. In those applications only 2 of the
LEDs will need to illuminate green to indicate a
good cable.
5. For shielded cable, you may test the shielding by pushing
the GND (Ground) button on. The pair LEDs and GND
LED should all illuminate green except for pair 3 & 6. If
any LEDs illuminate green first and red afterwards or do
not illuminate, the shielding is bad.
Caution:
1. Do not connect the cable tester to a live circuit.
2. Make sure the 9-Volt alkaline battery is installed
properly in the battery compartment.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
P73240_F5F315-T_US_man.qxd 9/24/03 3:21 PM Page 2
To Test Coax Cable (BNC)
1. Plug one end of cable to the BNC socket of master unit
and the other end to the BNC terminator included with
the F4F315-T.
2. Push the Power button to the ON position on the master
unit. If the BNC LED illuminates, the cable is bad.
3. If the cable passes step 2, then push the BNC test button
on the side of the master unit. The BNC LED will
illuminate green if the cable is good. If it illuminates red,
the cable is bad.
Pair Configurations For Cables
with Modular Connectors
2
Download from Www.Somanuals.com. All Manuals Search And Download.
P73240_F5F315-T_US_man.qxd 9/24/03 3:21 PM Page 3
Product Detail
BNC Terminator
Master Unit
Remote Terminator
3
Download from Www.Somanuals.com. All Manuals Search And Download.
P73240_F5F315-T_US_man.qxd 9/24/03 3:21 PM Page 4
be lkin.com
Belkin Components
501 West Walnut Street
Compton • CA • 90220 • USA
Tel: 310.898.1100
Fax: 310.898.1111
Belkin Components, Ltd.
Unit 13 • Gatelodge Close • Round Spinney
Northampton • Northants • NN3 8RX • UK
Tel: +44 (0) 1604678300
Fax: +44 (0) 1604678330
Belkin Components B.V.
Diamantlaan 8 • 2132 WV
Hoofddorp • The Netherlands
Tel: +31 (0) 235698765
Fax: +31 (0) 235612694
©1999 Belkin Components. All Rights Reserved. All Trade Names are
Registered Trademarks of Respective Manufacturers Listed.
Download from Www.Somanuals.com. All Manuals Search And Download.
P73240_F5F315-T_US_man.qxd 9/24/03 3:21 PM Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
P73240_F5F315-T_US_man.qxd 9/24/03 3:21 PM Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
|