USB Parallel Printer
Adapter
Packing Checklist
(1) One Belkin USB Parallel Printer Adapter with
connectors for USB type A port and a Centronics
36 male port
Floppy Disk Installation Software
User Guide
Please read this manual thoroughly and follow the
procedures to prevent any damage to the USB Parallel
Printer Adapter and/or to the connected devices.
F5U002
Introduction
The Belkin Components USB Parallel Printer Adapter will allow any Windows® 98 PC equipped with a USB port to print
to any parallel printer. USB allows the connection of up to 127 devices to a single PC. Simply plug the USB connector into
the computer USB port and the Centronics connector into the appropriate printer. This installation procedure automatically
detects the adapter and sets up your system to use your printer device every time your computer is started.
The Belkin USB Parallel Printer Adapter is also supported by a one year warranty and free technical support should you
have any questions about installing or using the USB Parallel Printer Adapter.
Product Features
Requirements
Hardware
IBM 486 compatible processor or higher
USB port
Operating Systems Requirements
This software runs in Windows® 95, and Windows® 98 and Windows® 98SE. Windows® 95 must be OSR2.1 version
1214 which contains the USB supplement.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
5. To complete the uninstall, you will be asked to
reboot your computer. Click Yes to reboot your
computer now. Once you reboot you will not have to
reboot where indicated in Step 2 of the installation
instructions.
4. If the USB Parallel Printer Adapter is not plugged in, you
will see the message under the "Print to the following port"
box in Figure 3. Plug the Belkin USB Parallel Printer
Adapter into the printer as show in Step 4 of New
Installation.
6. Proceed with the installation instructions beginning
with Step 3 to reinstall the Parallel Printer Adapter.
Figure 3
TROUBLESHOOTTING
1. To install the Parallel Printer Adapter you must
have all the USB components installed.
a) First ensure that the USB interface for your
computer's CMOS has been enabled. Check your
computer's user manual on how to configure
your CMOS.
b) Second, open My Computer, open the Control
Panel folder and then open the System icon. Click
the Device Manager tab. The last device you see
should say Universal Serial Bus controller. If
not, you will need to install it from your
Windows® 98 CD.
2. If you already have the USB Parallel Printer
Adapter installed and you are updating to
Windows® 98, then return to the section entitled
Overwrite Previous Installation,
3. If the Device ID cannot be retrieved from the printer
as shown in Figure 2, reinstall your printer with the
printer manufacturer's software on the parallel
port(LPT1) like a normal printer installation.
5. If the error message appears in Figure 4, simply
update your Windows" operating system to
Windows® 98.
Figure 4
Figure 2
6. If you are still unable to print, the drivers for your printer
may not support bi-directional printing through a USB to
parallel adapter. For instructions on
disabling bi-directional printing, please visit our web site at
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Software Components
CE Declaration of Conformity
The software necessary for standard PnP installation and
operation of the USB Parallel Printer Adapter consist of the
following:
We, Belkin Components, declare under our sole
responsibility that the F5UO02, to which this declaration
relates, is in conformity with EUROPEAN STANDARD
EN 55022/Al Class B, and EN 50082-1 (IEC 801-2, IEC
801-3, IEC 801-4).
1. Class Installer
BPPU2PAR.SYS
FU5002.INI
ETKPRCI.DLL
BPPPMON.DLL
F5U002A.INF
F5U002.INF
2. VVDM device driver
3. Port monitor installer
4. Port monitor
THE WARRANTY AND REMEDIES SET FORTH
ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL
OTHERS, WHETHER ORAL OR WRITTEN, EXPRESS
OR IMPLIED. BELKIN SPECIFICALLY DISCLAIMS
ANY AND ALL IMPLIED WARRANTIES, INCLUDING,
WITHOUT LIMITATION, WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE.
5. Install file
6. Uninstall Program
BPPUNIN1.EXE
FCC/CE Statement
This equipment has been tested and found to comply with
the limits for a Class A & B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
No Belkin dealer, agent, or employee is authorized to make
any modification, extension, or addition to this warranty.
BELKIN IS NOT RESPONSIBLE FOR SPECIAL,
INCJDENTAL, OR CONSEQUENTIAL DAMAGES
RESULTING FROM ANY BREACH OF WARRANTY,
OR UNDER ANY OTHER LEGAL THEORY,
INCLUDING BUT NOT LIMITED TO LOST PROFIT,
DOWNTIME, GOODWILL, DAMAGE TO OR
REPROGRAMMING, OR REPRODUCING ANY
PROGRAM OR DATA STORED IN OR USED WITH
BELKIN PRODUCTS.
interference by one or more of the following measures:
Some states do not allow the exclusion or limitation of
incidental or consequential damages or exclusions of implied
warranties, so the above limitations of exclusions may not
apply to you. This warranty gives you specific legal rights,
and you may also have other rights that vary from state to
state.
•Reorient or relocate the adapter.
•Increase separation between the hub, computer,
monitor and printer.
*Connect the equipment into an outlet or a circuit
different from the one that it is currently connected.
•Consult dealer or technical support for help.
Belkin Components Product Warranty
Belkin Components warrants this product against defects
in materials and workmanship for the life of the product.
If a defect is discovered, Belkin will, at its option, repair
or replace the product at no charge, provided it is returned
during the warranty period, with transportation charges
prepaid, to the authorized Belkin dealer from whom you
purchased the product. Proof of purchase
501 West Walnut Street - Compton - CA - 90220-5221
800.223.5546* 310.898.1100 - FAX 310.898.1111 *
may be required.
Belkin Components, Ltd.
This warranty does not apply if accident, abuse, misuse,
or misapplication has damaged the product; if the product
has been modified without the permission of Belkin; or if
any Belkin serial number has been removed or defaced.
Clarke Road - Mount Farm - Bletchley, Milton Keynes * MKI 1LG
Phone +44 (0) 1908367178 * FAX +44 (0) 1908366564
©1999 Belkin Components. All Rights Reserved. All Trade Names Are
Registered Trademarks Of Respective Manufacturers Listed.
P72670
4
Download from Www.Somanuals.com. All Manuals Search And Download.
|