Play
wireless router
User Manual
F7D4302au 8820au00380
Download from Www.Somanuals.com. All Manuals Search And Download.
GeTTInG sTaRTeD
What’s in the box
Initial setup
Play Wireless Router
Where to Place Your Router
Ethernet cable (attached to router)
Power supply (attached to router)
Network information card (attached to router)
Belkin Setup CD with User Manual
For the best results, place the Router next to your modem in
an open location away from large metal objects and magnets
such as those found in speakers. Raising the Router above
floor level can improve the strength of your wireless signal.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
GeTTInG sTaRTeD
How to set It Up
2
Download from Www.Somanuals.com. All Manuals Search And Download.
GeTTInG sTaRTeD
1 Connect your Router’s Ethernet cable to your modem’s Ethernet
port (on the back of your modem). This port might be labeled
differently on your particular modem. If you are adding a
Router for the first time, this port may be connected to your
computer by an Ethernet cable. It is OK to disconnect your
computer and plug the Router into the modem instead.
2 Plug the Router’s power supply into a wall outlet.
3 Put the CD into your computer. If the CD doesn’t
open automatically, please browse to your CD drive
and double-click on the Belkin Setup CD icon.
Setup
4 Click the Setup icon on the CD menu.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GeTTInG sTaRTeD
5 After a brief installation, the setup software will ask you
for the network name and password from the network
information card that is attached to your Router. Store the
card under the base of your Router for future reference.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
GeTTInG sTaRTeD
6 A progress screen will appear while additional software is
installed. This may take a few minutes to complete. Once
finished, a “Success” message will appear indicating that you
are connected to the Internet via your new Belkin Router.
During setup you may be asked for additional information
You may need to enter a username and password provided
by your ISP. This username and password is likely to be
found on materials that came from your ISP when you
signed up for service. If necessary, you may need to contact
your ISP to retrieve your username and password.
If you have a static IP address, you may need to enter
additional information also provided by your ISP.
If your computer doesn’t have a wireless adapter, or the
setup software is unable to control it, you may be asked to
connect your computer to the Router with a network cable.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
GeTTInG sTaRTeD
advanced Tools & settings
After the initial setup is complete, you have the option to
change settings like your network name, security type, and
password. To make these changes and others, click on the
Advanced Tools icon at the CD Setup menu and select one
of the following settings that you would like to change:
network name & security – Personalize your network name
(SSID), password, and strength of wireless security.
Internet service Provider & login settings – Have
you moved or changed Internet Service Providers?
If you’d like to change these settings without running
through the setup process again, this is the place.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
GeTTInG sTaRTeD
The belkin Router Manager
The Belkin Router Manager appears in your system tray
(Windows) or menu bar (Mac). Its icon indicates the current
status of your Router and also allows you to access your
Router’s settings to make changes. It also provides quick
access to software that came bundled with your Router.
Belkin.2234
Router Settings
User Manual
To access the Router settings, click on the icon
and select from the menu that appears.
The status of your Router is shown by the Belkin Router Manager
icon, which closely mimics the light on the front of the Router.
USB Print & Storage Manager
Memory Safe: Get Started!
Green: You are connected to your Belkin Router
and it is connected to the Internet.
amber: You are connected to your Belkin Router,
but it is not connected to the Internet.
Daily DJ: Get Started!
Music Labeler
Check for Updates
Options
Exit
7
Download from Www.Somanuals.com. All Manuals Search And Download.
GeTTInG sTaRTeD
Manual setup Using Your browser
in anything else such as “www”). Then press the Enter key. If
you’re still having trouble running the manual setup option, type
“192.168.2.1” in your browser (you do not need to type in anything
8
Download from Www.Somanuals.com. All Manuals Search And Download.
GeTTInG sTaRTeD
Using the CD
adding Computers to Your network
1 Put the Setup CD into your computer. If the CD
doesn’t open automatically, browse to your CD
drive and open the Belkin Setup CD icon.
Wireless devices such as computers, network printers, and gaming
systems can connect to your Router with a few simple steps.
2 Click the Setup icon on the CD menu.
3 After a brief installation, the setup software will ask you for the
network name and password from the network information card
that came with your Router. This card is most likely now located
underneath the foot of your Router in the provided card slot.
4 A progress screen will appear while additional software is
installed. This may take a few minutes to complete. Once
finished, a “Success” message will appear indicating that you
are connected to the Internet via your new Belkin Router.
note: The setup software runs only on
Windows and Mac OS X systems.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
GeTTInG sTaRTeD
Manually
Using the WPs button
If you choose not to use the included Setup CD for
adding additional computers or wireless devices, you
can manually add these items to your network.
1 Start WPS Push Button Connection (WPS PBC) on your
computer or other Wi-Fi device that you would like to connect
wirelessly to your Router. Often there will be a button for this
purpose in software that came with the device, or a physical
“WPS,” “PBC,” or “Security” button on the device itself.
1 Locate the wireless-network-connections option
on your computer or wireless device.
2 Within two minutes, press the WPS button on your Router.
2 Select your Belkin Router from the list of available networks. You
can identify your Belkin Router by locating the network name
(SSID) from the card located underneath the foot of your Router.
The WPS light (small light above WPS button) will blink green while
it listens for your Wi-Fi device. Once a connection is established, the
light will turn green and then go out. If a connection is not established,
the light will blink amber. You may repeat the process to try again.
3 Enter your network password (located on
your network information card).
You can repeat this process for each WPS-enabled
device you’d like to add to your network.
Your wireless device will take a few moments to connect to your
network. If the connection is not made the first time, try this
process again. If you still have difficulty connecting to your network
after trying this process a few times, see the “Troubleshooting”
section in this manual for help with connecting to your network.
note: In some cases you may be prompted to select the
security type. It is printed on the card for your convenience.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
GeTTInG sTaRTeD
adding Usb Devices
11
Download from Www.Somanuals.com. All Manuals Search And Download.
GeTTInG sTaRTeD
adding a Drive
adding a Printer
You can share a USB hard drive or flash drive to your network via
your Router’s USB port. Once connected, you can share files and
music with other computers and devices within your network.
You can add a printer to your network via your Router’s
USB port. Once connected, you can print from various
computers and wireless devices within your network.
Plug your USB hard drive into the USB port on the back
of your Router. When the light above the USB port is lit,
your drive is available to computers on your network.
Plug your printer’s USB cable into the USB port located on
the back of your Router. When the light above the USB port is
lit, your printer is available to computers on your network.
You can manually check the status of your shared drive by visiting
the USB Print and Storage Manager, found under the Belkin Router
Manager icon displayed in your system tray (Windows) or menu
bar (Mac). If you have difficulty sharing a drive on your network,
please see the “Troubleshooting” section of this manual.
You can manually check the status of your printer by visiting the
USB Print and Storage Manager, found under the Belkin Router
Manager icon displayed in your system tray (Windows) or menu
bar (Mac). If you have difficulty sharing a printer on your network,
please see the “Troubleshooting” section of this manual.
note: Each computer that will use the printer must have
both the Belkin software and the printer’s driver installed.
If the print driver is not installed, you will be asked to install
it by the Belkin USB Print and Storage Manager.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
GeTTInG sTaRTeD
adding Other Usb Devices
Other USB devices may also be shared via your Router.
Plug your device into the USB port located on the back of
your Router. When the light above the USB port is lit, your
device is available to computers on your network.
Computers running the Belkin USB Print and Storage Manager will
be able to make use of the shared device by visiting the USB Print
and Storage Manager, found under the Belkin Router Manager
icon displayed in your system tray (Windows) or menu bar (Mac).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
GeTTInG sTaRTeD
Memory safe
bundled software
Memory Safe allows you to set up a routine backup of your
files to a hard drive or flash drive attached to your Router.
Memory Safe is found in the Belkin Router Manager icon
displayed in your system tray (Windows) or menu bar (Mac).
Usb Print and storage Manager
The USB Print and Storage Manager helps to manage and
monitor the use of your USB printers, scanners, hard drives,
and other devices that are connected to your Router’s USB
port and shared across your network. USB Print and Storage
Manager is found in the Belkin Router Manager icon displayed
in your system tray (Windows) or menu bar (Mac).
Music labeler
Belkin Music Labeler corrects metadata (track names, artist
names, track numbers, etc.) in your iTunes and Windows Media
libraries, making it easy to find the music you are looking for.
Music Labeler is found under the Belkin Router Manager icon
displayed in your system tray (Windows) or menu bar (Mac).
When you have one or more USB devices attached to your
Router, the main actions for those devices are available
directly from the Belkin Router Monitor menu.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
GeTTInG sTaRTeD
Daily DJ
Belkin Daily DJ delivers personalized playlists from your
music collection, automatically, every day. It’s like having your
own personal DJ playing the songs that you want to hear. It
works great with iTunes and Windows Media Player. Daily
DJ is found under the Belkin Router Manager icon displayed
in your system tray (Windows) or menu bar (Mac).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
GeTTInG sTaRTeD
Video Max
additional Capabilities
Video Max automatically prioritizes your network traffic to
ensure high-quality streaming video, VoIP calls, and games.
Guest access
Music Mover
You can allow guests to use your Internet connection without
joining your personal network. The network name and
password for the guest network is located on the network
information card found under the foot of your Router.
Music Mover sends music from a USB drive attached to your
Router to any UPnP (Universal Plug-and-Play) or DLNA-compatible
device on your network. These devices include certain gaming
systems, televisions, Blu-ray players, and cell phones.
A person using your guest network will be able to join
without a password, but will be shown a login page when
they attempt to surf the Web. They will need to enter
the guest password into this page to continue.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
GeTTInG TO KnOW YOUR ROUTeR
front Panel
b) Wi-fi Protected setup (WPs) light and button
The WPS button on the front of your Router can be used to
help establish a secure connection between your Router and
other WPS-enabled Wi-Fi devices such as computers. To use
the WPS feature on your Router, see “Getting Started > Adding
Computers to Your Network > Using the WPS Button”.
(a)
(b)
The small light near the WPS button shows what is happening
while you are using WPS to establish a connection.
Off: Idle
blinking Green: The Router is listening for a
WPS-enabled computer or other device.
a) Router status light
solid Green: The Router has made a secure
Your Router’s status is shown by the light on the front.
Off: The Router is not plugged into a power source.
blinking Green: The Router is starting up.
solid Green: The Router is connected to the Internet.
connection with the computer or other device.
amber: A connection was not created.
blinking amber: The Router can’t detect the modem. Either the
modem is off, is not plugged into the Router, or is unresponsive.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
GeTTInG TO KnOW YOUR ROUTeR
back Panel
a) Modem (Wan) Connector
C) Usb Port
D) Reset button
Connect your modem to this
port using an Ethernet cable.
USB printers, disks, and other
USB devices plugged into this
port will be shared on your
network. Each USB port has a
light that indicates its status.
This button is used to restart
your Router in rare cases when it
functions incorrectly. Resetting
the Router will preserve your
settings. This button may also
be used to restore the factory
default settings. Please see
the Troubleshooting section
for more information.
(a)
b) Wired (lan) Connectors
Off: No USB device is
Connect computers and other
wired network devices to these
ports using Ethernet cables.
connected or the attached
USB device is not in use.
(b)
blinking: Please wait to
unplug the device until
the light turns off.
e) Power Connector
On: The USB device is
connected and being
shared on your network.
Connect the included power
supply to this jack.
(c)
(d)
(e)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
TeCHnICal DeTaIls
Universal Plug-and-Play (UPnP) Compatibility
Technical features
The UPnP (Universal Plug-and-Play) feature in your Router
offers seamless operation of voice and video messaging,
games, and other applications that are UPnP-compliant.
Integrated 802 11n Wireless access Point
Utilizing Dual-Band Network technology, your Router
creates two separate networks (one at 2.4GHz band and
the other at 5GHz band), allowing increased bandwidth to
all your connected wireless devices and computers.
Web-based advanced User Interface
You can easily make changes to your Router’s advanced
settings through your web browser. These changes can
be made from any computer on your network.
naT IP address sharing
belkin Router Monitor
To save you the cost of adding IP addresses per
computer in your house, your Belkin Router uses Network
Address Translation (NAT) technology, allowing you to
share a single IP address across your network.
The Belkin Router Monitor application helps you to monitor
your Router’s status and change network settings.
Integrated 4-Port 10/100 switch
sPI firewall
Your Router has a built-in, 4-port network switch to
allow your wired computers to share: printers, data,
MP3 files, digital photos, and much more.
Your Router is equipped with a firewall that will protect your
network from a wide array of common attacks and viruses.
Usb Port
The USB port lets you plug in printers, hard drives, and
other USB devices to share across your network.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
TeCHnICal DeTaIls
setup software
system Requirements
A computer running Windows® XP SP2 or higher,
Windows Vista®, or Windows 7; or Mac OS® X v10.x
Router
Minimum 1GHz processor and 256MB RAM
600MB of free hard-drive space for installation
Broadband Internet connection such as a cable or
DSL modem with RJ45 (Ethernet) connection
At least one computer with an installed network interface adapter
TCP/IP networking protocol installed on each computer
RJ45 Ethernet networking cable
Memory safe and Usb Print and storage Manager
Windows XP SP2 or higher or Windows
Vista; or Mac OS X v10.4 or later
Internet browser
Minimum 1GHz processor and 256MB RAM
50MB of free hard-drive space for installation
20
Download from Www.Somanuals.com. All Manuals Search And Download.
TeCHnICal DeTaIls
Daily DJ and Music labeler
PC
Windows XP SP2 or higher, Windows Vista, or Windows 7
2GHz processor
1GB of RAM
DirectX® 9.0-compliant video and sound
Internet Explorer® or Firefox®
Mac®
Mac OS X v10.4.8 or later
Intel® Core™ Duo 1.83GHz or higher processor
1GB of RAM
Safari® or Firefox
200MB of free hard-drive space for installation
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUblesHOOTInG, sUPPORT, anD WaRRanTY
belkin setup cannot find my Router
Troubleshooting
If Belkin Setup is not able to communicate with your Router during
the installation process, please check the following items.
The setup CD does not automatically start
1 Make sure that the wireless hardware on your
If Belkin Setup does not run when you insert the CD-ROM, your
computer may not be configured to open CDs automatically.
computer is turned on, if available.
2 Try connecting your computer to one of the four “wired”
If Belkin Setup does not appear within 15 seconds, browse
to your CD-ROM drive and open the “Belkin Setup” icon.
setup manually. Please see “Manual Setup Using Your
Browser” earlier in this manual for more information.
ports on the Router with an Ethernet cable.
3 Ensure that the Router is on. The front-panel light should be on.
4 Unplug the Router’s power supply for 10
seconds, then plug it back in.
5 There may be firewall software on your computer preventing
an outgoing connection. You may choose to temporarily
disable this software before attempting setup.
If Belkin Setup still cannot find the Router, you might choose
to do a manual setup. Refer to “Manually Configuring
Network Settings” in this manual for details.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUblesHOOTInG, sUPPORT, anD WaRRanTY
belkin setup cannot connect my Router to the Internet
belkin setup completed installation, but I cannot browse the
Web The light on the front of my Router is blinking amber
If Belkin Setup is not able to connect the Router to
the Internet, please check the following items:
1 Make sure the Router is connected to your modem with an
Ethernet cable via the Router’s one WAN (modem) port.
1 Use the troubleshooting suggestions within Belkin Setup.
2 Unplug the modem from its power source and make sure
2 If your ISP requires a user name and password, make sure that
you have typed in your user name and password correctly. Some
user names require that the ISP’s domain may be at the end of the
name. Example: “[email protected]”. The “@myisp.com” part of
the user name may need to be typed as well as your user name.
that it goes dark. Then reapply power to the modem.
3 Unplug your Router’s power supply, wait 10 seconds,
and plug it back in. This will cause the Router to try
to reestablish communication with the modem.
3 If you continue to have no Internet connection, refer
to “Manually Configuring Network Settings” in this
manual for an alternative setup method.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUblesHOOTInG, sUPPORT, anD WaRRanTY
belkin setup completed installation, but I cannot browse the
Web The light on the front of my Router is solid amber
I can’t connect to the Internet wirelessly
If the light on the front of the Router is solid green, then your
Router is connected to the Internet. You may not be connected
to the Router’s wireless network. Please refer to “Adding
Computers to Your Network” in this manual for instructions.
1 Use the troubleshooting suggestions within Belkin Setup.
2 If your ISP requires a user name and password, make sure that
you have typed in your user name and password correctly. Some
user names require that the ISP’s domain may be at the end of the
name. Example: “[email protected]”. The “@myisp.com” part of
the user name may need to be typed as well as your user name.
3 If you have a static connection, your ISP will have
assigned you an IP address, subnet mask, and gateway
address. Please re-run Belkin Setup and enter this
information when a static connection is mentioned.
4 You may need to configure your Router to meet
the specific requirements of your ISP. To search
our knowledge base for ISP-specific issues, go to:
http://www.belkin.com/support and type in “ISP”.
5 If you continue to have no Internet connection, refer
to “Manually Configuring Network Settings” in this
manual for an alternative setup method.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUblesHOOTInG, sUPPORT, anD WaRRanTY
I can’t connect to the Internet wirelessly and my
My wireless network performance is slow, inconsistent,
suffers from weak signal, or I’m having difficulty maintaining a
VPn connection
network name is not listed in available networks
1 Verify that your Router is on and the
front-panel light shows solid green.
Wireless technology is radio-based, which means connectivity
and the throughput performance between devices
2 If you are far from the Router, you might try moving
decreases when the distance between devices increases.
Other factors that will cause signal degradation (metal is
generally the worst culprit) are obstructions such as walls
and metal appliances. Note also that connection speed may
decrease as you move farther away from the Router.
closer to see if you might have been out of range.
3 Using a computer attached to the Router via a network cable,
This setting is found on the “Channel and SSID” page.
In order to determine if wireless issues are related to
range, we suggest temporarily moving the computer
within 10 feet from the Router if possible.
Changing the wireless channel—Depending on local
wireless traffic and interference, switching the wireless
channel of your network can improve performance and
reliability. See the section titled “Changing the Wireless
Channel” for instructions on how to choose other channels.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUblesHOOTInG, sUPPORT, anD WaRRanTY
limiting the wireless transmit rate—Limiting the wireless transmit
rate can help improve range and connection stability. Most wireless
cards have the ability to limit the transmission rate. To change this
property in Windows, go to the Windows Control Panel, open “Network
Connections”, and double-click on your wireless card’s connection. In
the properties dialog, select the “Configure” button on the “General”
tab, then choose the “Advanced” tab and select the rate property.
I’ve installed this new Router and some of my network clients
(computers, game consoles, etc ) are now unable to connect
Your new Router came pre-configured with a network name and
password, found printed on an attached card. All clients must use this
network name and password to connect wirelessly to your Router.
You will need to find the network settings on your client, select the
network name printed on the card from the list of available networks,
and enter the password when prompted to join the wireless network.
Wireless client cards are usually set to automatically adjust
the wireless transmit rate for you, but doing so can cause
periodic disconnects when the wireless signal is too weak; as
a rule, slower transmission rates are more stable. Experiment
with different connection rates until you find the best one
for your environment. Note that all available transmission
rates should be acceptable for browsing the Internet. For
more assistance, see your wireless card’s user manual.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUblesHOOTInG, sUPPORT, anD WaRRanTY
Does the Router support Wireless
5 Click “Apply Changes” to finish. Your wireless
connection is now encrypted. Each computer using your
wireless network will need to use the new key.
Protected access (WPa) security?
The Router ships with WPA/WPA2 security turned on.
Windows XP and some older network hardware may
require a software update to support WPA/WPA2.
note: If you are configuring the Router over a wireless
connection, you will have to re-connect to the
Router after changing any security settings.
I am having difficulty setting up WPa security on my Router
note: Some older networking hardware supports
only WEP encryption. If your older computers cannot
connect to your network, try 128-bit or 64-bit WEP, or
seek software updates from their manufacturers.
Click on the “Login” button in the top right-hand corner of the
screen. You will be asked to enter your password. If you have never
set a password, leave the “Password” field blank and click “Submit”.
2 Click “Wireless” in the left-hand menu. Then
click “Security” just below that.
3 Select the “WPA/WPA2” option.
4 Enter a password. This can be from 8–63 characters of your choice,
including spaces and punctuation, OR a 64-digit hexadecimal
number (using only the numbers 0–9 and letters A–F).
27
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUblesHOOTInG, sUPPORT, anD WaRRanTY
I am having difficulty setting up Wired equivalent
Privacy (WeP) security on my Router
5 Click “Apply Changes” to finish. Your wireless
activity is now encrypted. Each computer using your
wireless network will need to use the new key.
Click on the “Login” button in the top right-hand corner of the
screen. You will be asked to enter your password. If you have never
set a password, leave the “Password” field blank and click “Submit”.
note: If you are configuring the Router over a wireless
connection, you will have to re-connect to the
Router after changing any security settings.
2 Click “Wireless” in the left-hand menu. Then
note: Some older networking hardware supports
only 64-bit WEP encryption. If your older computers
cannot connect to your network, try 64-bit WEP.
click “Security” just below that.
3 Select the “128-bit WEP” option.
4 You may type in a WEP key manually, or generate one from
a passphrase. Type a phrase in the “Passphrase” field and
click the “Generate” button. A WEP key is composed of 26
hexadecimal digits (0–9, A–F . For example, C3 03 0F AF
4B B2 C3 D4 4B C3 D4 EE 74 is a valid 128-bit WEP key.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUblesHOOTInG, sUPPORT, anD WaRRanTY
a disk I plugged into the Usb port is not showing
up on my computer or in Memory safe
a printer I plugged into the Usb port is
not showing up on my computer
1 Is the light on over the USB port that the disk is plugged into?
If not, try unplugging and re-plugging the disk. Please check
that the USB connector is firmly plugged into the Router.
1 Is the light on over the USB port that the printer is plugged into?
If not, try unplugging and re-plugging the printer. Please check
that the USB connector is firmly plugged into the Router.
2 If your disk has an optional power supply, please use
2 To print to a printer attached to the Router, your
computer must have that printer’s driver installed.
Please check that the driver is installed.
it while the disk is attached to your Router.
3 The Router supports FAT16, FAT32-, or NTFS-formatted
disks. Disks in other formats will not appear in the
Finder (Mac OS X) or Windows Internet Explorer.
3 The printer may not be set to auto-connect. Via the Belkin Router
Manager, open the USB Print and Storage Center. Check that the
printer appears in the list of available devices. View the properties
of the printer, and check that “auto-connect” is selected.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUblesHOOTInG, sUPPORT, anD WaRRanTY
a different sort of Usb device that I plugged into the
Usb port is not showing up on my computer
Most USB devices other than disks and printers must be
accessed via the USB Print and Storage Center.
1 Is the light on over the USB port that the device is plugged into?
If not, try unplugging and re-plugging the device. Please check
that the USB connector is firmly plugged into the Router.
2 Via the Belkin Router Manager, open the USB
Print and Storage Center. Check that the device
appears in the list of available devices.
3 Select the device and click the “Use” button. The device will be
virtually connected to your computer until you choose to “Stop
Using” the device, or another person requests use of the device.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUblesHOOTInG, sUPPORT, anD WaRRanTY
Technical support
Us
Thailand
0018004413318
UK
Philippines
180014410282
australia
Hong Kong
30021318
new Zealand
China
800 819 0159
europe
australia
1800 235 546
singapore
1800 622 1130
new Zealand
0800 235 546
Malaysia
1 800 812 076
asia email
India
1800-419-5546
Korea email
31
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUblesHOOTInG, sUPPORT, anD WaRRanTY
What is not covered by this warranty?
belkin International, Inc , limited
All above warranties are null and void if the Belkin product is
not provided to Belkin for inspection upon Belkin’s request
at the sole expense of the purchaser, or if Belkin determines
that the Belkin product has been improperly installed, altered
in any way, or tampered with. The Belkin Product Warranty
does not protect against acts of God such as flood, lightning,
earthquake, war, vandalism, theft, normal-use wear and tear,
erosion, depletion, obsolescence, abuse, damage due to low
voltage disturbances (i.e. brownouts or sags), non-authorized
program, or system equipment modification or alteration.
3-Year Product Warranty
What this warranty covers
Belkin International, Inc. (“Belkin”) warrants to the original
purchaser of this Belkin product that the product shall be free
of defects in design, assembly, material, or workmanship.
What the period of coverage is
Belkin warrants the Belkin product for three years.
What will we do to correct problems?
Product Warranty.
Belkin will repair or replace, at its option, any defective product
free of charge (except for shipping charges for the product).
Belkin reserves the right to discontinue any of its products without
notice, and disclaims any limited warranty to repair or replace any
such discontinued products. In the event that Belkin is unable to
repair or replace the product (for example, because it has been
discontinued), Belkin will offer either a refund or a credit toward
the purchase of another product from Belkin.com in an amount
equal to the purchase price of the product as evidenced on the
original purchase receipt as discounted by its natural use.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUblesHOOTInG, sUPPORT, anD WaRRanTY
How to get service
Belkin reserves the right to review the damaged Belkin product.
All costs of shipping the Belkin product to Belkin for inspection
shall be borne solely by the purchaser. If Belkin determines,
in its sole discretion, that it is impractical to ship the damaged
equipment to Belkin, Belkin may designate, in its sole discretion,
an equipment repair facility to inspect and estimate the cost to
repair such equipment. The cost, if any, of shipping the equipment
to and from such repair facility and of such estimate shall be
borne solely by the purchaser. Damaged equipment must remain
available for inspection until the claim is finalized. Whenever
claims are settled, Belkin reserves the right to be subrogated
under any existing insurance policies the purchaser may have.
To get service for your Belkin product you
must take the following steps:
1 Contact Belkin International, Inc., at 12045 Waterfront
Drive, Los Angeles, CA 90094, Attn: Customer Service,
or call (800)-223-5546, within 15 days of the Occurrence.
Be prepared to provide the following information:
a. The part number of the Belkin product.
b. Where you purchased the product.
c. When you purchased the product.
d. Copy of original receipt.
2 Your Belkin Customer Service Representative will then
instruct you on how to forward your receipt and Belkin
product and how to proceed with your claim.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUblesHOOTInG, sUPPORT, anD WaRRanTY
How state law relates to the warranty
THIS WARRANTY CONTAINS THE SOLE WARRANTY OF
BELKIN. THERE ARE NO OTHER WARRANTIES, EXPRESSED
OR, EXCEPT AS REQUIRED BY LAW, IMPLIED, INCLUDING
THE IMPLIED WARRANTY OR CONDITION OF QUALITY,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, AND SUCH IMPLIED WARRANTIES, IF ANY, ARE
LIMITED IN DURATION TO THE TERM OF THIS WARRANTY.
Some states do not allow limitations on how long an implied
warranty lasts, so the above limitations may not apply to you.
IN NO EVENT SHALL BELKIN BE LIABLE FOR INCIDENTAL,
SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL OR
MULTIPLE DAMAGES SUCH AS, BUT NOT LIMITED TO,
LOST BUSINESS OR PROFITS ARISING OUT OF THE
SALE OR USE OF ANY BELKIN PRODUCT, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
This warranty gives you specific legal rights, and you may also have
other rights, which may vary from state to state. Some states do
not allow the exclusion or limitation of incidental, consequential,
or other damages, so the above limitations may not apply to you.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
ReGUlaTORY InfORMaTIOn
fCC statement
federal Communications Commission notice
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
DeClaRaTIOn Of COnfORMITY WITH fCC RUles
fOR eleCTROMaGneTIC COMPaTIbIlITY
We, Belkin International, Inc., of 12045 Waterfront Drive, Los Angeles,
CA 90094, declare under our sole responsibility that the device, ,
f7D4302 v1, complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment generates, uses, and can radiate radio frequency
energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try and
correct the interference by one or more of the following measures:
Caution: exposure to Radio frequency Radiation
The device shall be used in such a manner that the potential
for human contact normal operation is minimized
•
•
•
Reorient or relocate the receiving antenna.
Increase the distance between the equipment and the receiver.
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum
distance of 20cm between the radiator and your body.
Connect the equipment to an outlet on a circuit different
from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
This device and its antenna(s) must not be co-located or
operating in conjunction with any other antenna or transmitter.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
ReGUlaTORY InfORMaTIOn
Canada-Industry Canada (IC)
Information
The wireless radio of this device complies with RSS
139 & RSS 210 Industry Canada. This Class B digital
apparatus complies with Canadian ICES-003.
Products with the CE marking comply with the EMC Directive
(2004/108/EC) and the Low Voltage Directive (2006/95/
EC) issued by the Commission of the European Community.
Compliance with these directives implies conformity to
the following European Product Family Standards.
Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device
must accept any interference, including interference
that may cause undesired operation of the device.
•
•
•
•
•
EN 55022 (CISPR 22) – Electromagnetic Interference
EN 55024-1 – Electromagnetic Immunity
EN 61000-3-2 (IEC610000-3-2) – Power Line Harmonics
EN 61000-3-3 (IEC610000) – Power Line Flicker
EN 60950-1 (IEC60950-1) – Product Safety
Cet appareil numérique de la classe B conforme
á la norme NMB-003 du Canada.
europe
Products that contain the radio transmitter are sometimes
labeled with the Notified Body number (CE0560) or CE
alert marking if the standard used in the conformity is
not harmonized across the European Community.
European Union Radio products with the CE or CE alert
marking comply with the R&TTE Directive (1999/5/EC)
issued by the Commission of the European Community.
Compliance with this directive implies conformity
to the following European Norms (in brackets are
the equivalent international standards).
•
•
•
EN 60950-1:2006 (IEC60950-1) – Product Safety
EN 300 328 Technical requirement for radio equipment
ETS 301 489 General EMC requirements for radio equipment.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2010 Belkin International, Inc. All rights reserved. All trade names are registered trademarks of
respective manufacturers listed. Mac, Mac OS, and Safari are trademarks of Apple Inc., registered in the
U.S. and other countries. Windows, Windows Vista, Internet Explorer, and DirectX are either registered
trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
Download from Www.Somanuals.com. All Manuals Search And Download.
|