Washing Machine
User’s Manual
D2 8101 ES
D2 8101 E
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Auxiliary functions..............................19
Time display ......................................19
Starting the Program .........................20
Progress of program..........................20
Changing the selections after the
program has started..........................21
Switching the machine to standby mode
21
1 Your Washing Machine
4
Overview .............................................4
Specifications......................................5
2 Warnings
6
General Safety.....................................6
First Use..............................................6
Intended use .......................................6
Safety instructions ...............................7
If there are children in your house... .....7
Child-proof lock.................................21
Ending the program through canceling ..
22
Program in rinse hold mode...............22
End of program .................................22
3 Installation
8
Removing packaging reinforcement.....8
Opening the transportation locks.........8
Appropriate installation location ...........8
Adjusting the feet.................................8
Connecting to the water supply. ..........9
Connecting to the drain .......................9
Electrical connection .........................10
Destroying the packaging material.....10
Disposing of the old machine.............10
6 Quick instructions for daily
use
23
25
7 Cleaning and care
Detergent drawer...............................25
The door and the drum......................25
Outer cabinet and control panel.........25
Inlet water filters.................................25
Draining any remaining water and
4 Initial preparations for
cleaning the pump filter .....................26
washing
11
8 Solution suggestions for
problems
Sorting the laundry ............................11
Preparing clothes for washing............11
Correct load capacity ........................11
Loading door.....................................12
Detergents and softeners ..................12
28
5 Selecting a Program and
Operating Your Machine
14
Control panel.....................................14
Display symbols.................................15
Turning the machine on .....................15
Program selection..............................15
Additional programs .........................16
Special programs ..............................16
Temperature selection........................16
Spin Speed selection.........................17
Program and consumption table........18
Download from Www.Somanuals3.co-mE. ANll Manuals Search And Download.
1 Your Washing Machine
Overview
3
4
1
2
5
6
1 - Detergent Drawer
2 - Door
4 - Control Panel
5 - Filter Cap
3 - Top Lid
6 - Height-adjustable feet
Download from Www.Somanuals4.co-mE. ANll Manuals Search And Download.
Specifications
Models
D2 8101 E
D2 8101 ES
Maximum dry laundry capacity (kg)
Height (cm)
8
8
84
60
59
74
84
60
59
74
Width (cm)
Depth (cm)
Net Weight (±4 kg)
Electricity (V/Hz.)
Total Current (A)
Total Power (W)
Spinning cycle (rpm max.)
220-240 V / 50Hz
10
10
2000-2350
1000
1000
Specifications of this appliance may change without notice to improve the quality of
the product. Figures in this manual are schematic and may not match your product
exactly.
Values stated on the machine labels or in the documentation accompanying it are
obtained in laboratory in accordance with the relevant standards. Depending on
operational and environmental conditions of the appliance, values may vary.
Download from Www.Somanuals5.co-mE. ANll Manuals Search And Download.
2 Warnings
Please read the following information.
Otherwise, there may be the risk of
personal injury or material damage.
Moreover, any warranty and reliability
commitment will become void.
for 3 seconds to cancel the program
set in your machine before calling
the authorized service.
First Use
•
To prepare your machine for
General Safety
washing, carry out your first washing
process without loading your
•
Never place your machine on a
carpet covered floor. Otherwise,
lack of airflow from below of your
machine may cause electrical
parts to overheat. This may cause
problems with your washing
machine and with detergent under
“Cottons 90°C” program.
•
Ensure that the cold and hot water
connections has been made
correctly when installing your
machine.
machine. Otherwise, your laundry
may come out hot at the end of the
washing process and may wear out.
If the current fuse or circuit breaker
is less than 16 Amperes, please
have a qualified electrician install a
16 Ampere fuse or circuit breaker.
While using with or without a
•
•
If the power cable or mains plug is
damaged you must call Authorized
Service for repair.
Check water hoses for wear. Do
not use old/used water inlet hoses.
These may cause stains on your
laundry.
•
•
•
Fit the drain hose into the discharge
housing securely to prevent any
water leakage and to allow machine
to take in and discharge water as
required. It is very important that the
water intake and drain hoses are not
folded, squeezed, or broken when
the appliance is pushed into place
after it is installed or cleaned.
Your washing machine is designed
to continue operating in the event
of a power interruption. You cannot
cancel any program by pressing the
“On/Off button.” Your machine will
not resume its program when the
power restores. Press the “Start/
Pause/Cancel” button for 3 seconds
to cancel the program (See,
transformer, do not neglect to have
the grounding installation laid by a
qualified electrician. Our company
shall not be liable for any damages
that may arise when the machine is
used on a line without grounding.
To make your machine ready for
use, please be sure that the tap
water supply and water drainage
systems are appropriate before
calling the authorized service. If they
are not, call a qualified plumber to
have any necessary arrangements
carried out.
•
•
Intended use
•
This product has been designed for
home use.
Cancelling a Program)
•
The appliance may only be used for
washing and rinsing of textiles that
are marked accordingly.
•
•
There may be some water in your
machine when you receive it. This is
from the quality control process and
is normal. It is not harmful to your
machine.
Some problems you may encounter
may be caused by the software.
Press “Start/Pause/Cancel” button
•
•
Only detergents, softeners and
supplements suitable for washing
machines may be used.
Observe the care instructions
labelled on textile products and
any other instructions given by
Download from Www.Somanuals6.co-mE. ANll Manuals Search And Download.
companies that produce detergents
for your machine.
be solved by information in the
operating manual:
Turn off the machine, unplug it, turn
off the water tap and contact an
authorized service agent.
•
This appliance is not intended for
use by persons (including children)
with reduced physical, sensory
or mental capabilities, or lack of
experience and knowledge, unless
they have been given supervision
or instruction concerning use of the
appliance by a person responsible
for their safety.
If there are children in your
house...
•
Electrical appliances may be
dangerous for the children. Keep
children away from the machine
when it is operating. Do not let them
tamper with the machine.
Safety instructions
•
•
•
This appliance must be connected
to an earthed outlet protected by a
fuse of suitable capacity.
•
•
Close the door when you leave the
area where the machine is located.
Store all detergents in a safe place
out of reach of the children.
The supply and draining hoses must
always be securely fastened and
remain in an undamaged state.
Fit the draining hose to a washbasin
or bathtub securely before starting
up your machine. There may be a
risk of being scalded due to high
washing temperatures!
•
•
Never open the door or remove the
filter while there is still water in the
drum. Otherwise, there may be the
risk of flooding and possible injury
due to the hot water.
Never force open the locked door!
The door will be ready to open just a
few minutes after the washing cycle
comes to an end.
Unplug the machine when it is not in
use.
Never wash down the appliance
with a water hose! There is the risk
of electric shock! Always disconnect
from the mains by unplugging before
cleaning.
Never touch the plug with wet
hands. Never unplug by pulling
on the cable, always pull out from
the plug only. Do not operate the
machine if the power cord or plug is
damaged.
•
•
•
•
•
Never attempt to repair the machine
yourself. Otherwise, you may be
putting yours and other’s lives in
danger.
For malfunctions that cannot
Download from Www.Somanuals7.co-mE. ANll Manuals Search And Download.
3 Installation
bolts in a safe place to reuse when
the washing machine needs to be
moved again in the future.
Removing packaging
reinforcement
Tilt the machine to remove the
packaging reinforcement. Remove the
packaging reinforcement by pulling the
ribbon.
C Never move the appliance without
the transportation safety bolts
properly fixed in place!
Appropriate installation
location
Install the appliance in environments
which have no risk of freezing, in a
stable and level position.
C The floor must be capable of
carrying the load on it!
C If the washing machine and a drier
are placed on top of each other,
their approximate weight together
may reach 180 kg when they are
full.
Important:
Opening the transportation
•
•
•
Do not place the appliance on top of
the power cable.
locks
Keep at least 1cm distance from the
edges of other furniture.
Place the machine on a firm surface;
do not position it on a long pile rug
or such like surfaces.
C Transportation safety bolts must
be removed before operating the
washing machine! Otherwise, the
machine will be damaged!
1. Loosen all the bolts with a spanner
until they rotate freely (“C”)
Adjusting the feet
C Do not use any tools to loosen the
lock nuts. Otherwise, they can be
damaged.
1. Manually (by hand) loosen the lock
nuts on the feet.
2. Remove transportation safety bolts
by turning them gently.
2. Adjust them until the machine
stands level and firm.
3. Important: Tighten all lock nuts up
again.
3. Fit the covers (supplied in the bag
with the Operation Manual) into the
holes on the rear panel. (“P”)
C Keep the transportation safety
Download from Www.Somanuals8.co-mE. ANll Manuals Search And Download.
Connecting to the water
supply.
Important:
•
The water supply pressure required
to run the machine must be 1-10
bar (0,1 – 1,0 MPa). Attach a
pressure-reducing valve if the water
pressure is higher.
•
Models with a single water inlet
should not be connected to the
hot water tap. Laundry may be
damaged or the appliance may
switch to protection mode and not
work.
•
Connect the special hoses supplied
with the machine to the water intake
valves on the machine. The hose
bearing the “red” sign (90°C max)
is the hot water inlet and the hose
bearing the “blue” sign (25°C max) is
for the cold water inlet.
When returning the appliance to its
place after maintenance or cleaning,
care should be taken not to fold,
squeeze or block the hoses.
Connecting to the drain
The water discharge hose can be
attached to the edge of a washbasin or
bathtub. The drain hose should be firmly
fitted into the drain as to not loosen in
its housing.
Important:
•
If you are going to use your double
water-inlet machine as a single
(cold) water-inlet unit, you must
install the stopper*, supplied with
your machine to the hot water valve.
If you want to use both water inlets
of the product, you can connect the
hot water hose after removing the
stopper and gasket group from the
hot water valve.
•
The end of the drain hose can
be directly connected to the
wastewater drain or to the
washbasin. The fitting must be
secured in all types of connections.
Your house may be flooded if the
hose falls out of its housing during
water discharging.
•
The hose should be attached to a
height of at least 40 cm, and 100
cm at most.
* Applies for the products supplied
with a blind stopper group.
•
Open the taps completely after
making the hose connection to
check if there is any water leakage
at the connection points. Turn off
the tap and remove the nut in case
of any leakage. Retighten the nut
carefully after checking the seal.
To prevent any water leakage and
any other damage to be caused by
it, keep the taps closed when the
machine is not in use.
Download from Www.Somanuals9.co-mE. ANll Manuals Search And Download.
•
•
In case the hose is elevated
B The appliance must not be operated
unless it is repaired! There is the risk
of electric shock!
after laying it on the floor level or
close to the ground (less than
40 cm above the ground), water
discharge becomes more difficult
and the laundry may come out wet.
Therefore, the heights described in
the figure should be followed.
To prevent dirty water refilling the
machine, and to allow for easy
discharge, the end of the hose
must not be submerged in the drain
water. The end of the hose must be
able to take in air. The hose should
be pushed into the drainage for
more than 15 cm. If it is too long
you may have it shortened.
Destroying the packaging
material
Packaging material can be dangerous to
children. Keep the packaging materials
out of reach of children or dispose
them by classifying according to
waste directives. Do not dispose them
together with normal domestic waste.
Packaging materials of your machine are
manufactured from recyclable materials.
Disposing of the old machine
Dispose of your old appliance in an
environmental friendly manner.
•
•
The end of the hose should not be
bent, it should not be stepped on
and it must not be folded between
the drain and the machine.
•
You may refer to your local agent or
solid waste collection center in your
municipality to learn how to dispose
of your machine.
The length of the hose is too short,
you may add an extension hose
to the original section. The length
of the hose must not be longer
than 3.2 m after coming out of the
machine. To avoid water leakage
failures, the connection between the
extension hose and the drain hose
of the product must be fitted well
with an appropriate clamp as not to
come off and leak.
Before disposing of your old washing
machine, cut off the mains plug and
make the door lock unusable.
Electrical connection
Connect the machine to an earthed
outlet protected by a fuse of suitable
capacity.
Important:
•
•
•
Connection should comply with
national regulations.
Power cord plug must be within
easy reach after installation.
The voltage and the allowed fuse
protection are specified in the
section “Technical Specifications”.
The specified voltage must be equal
to your mains voltage.
•
•
Connection via extension cords or
multi-plugs should not be made.
B A damaged power cable must be
replaced by a qualified electrician.
10 - EN
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Initial preparations for washing
•
Empty pockets and remove all
Sorting the laundry
foreign objects such as coins, pens
and paper clips. If possible, turn
pockets out and brush.
•
Sort the laundry according to type
of fabric, color, and degree of soiling
and permissible water temperature.
Always follow the advice on the
garment labels.
•
Place small items like infants’
socks and nylon stockings, etc.
in a laundry bag, pillow case or
something similar. This will also save
your laundry from getting lost.
Place curtains in the machine with
care. Remove curtain rails and
pullers.
•
Non machine
washable
Washing water
Wash with
Do not wash
temperature sensitive, short
programmes.
•
•
Fasten zippers, sew loose buttons
and mend rips and tears.
Wash “machine washable” or “hand
washable” labelled products only
with an appropriate programme.
Do not wash colours and whites
together. New, dark coloured
cottons may release a lot of dye.
Wash them separately.
Bleach can be Do not use
Dry-cleanable
Do not
dry-clean
used
bleach
•
•
•
Tough stains must be treated
properly before washing. If you are
not sure, check with a dry cleaner.
Use only dyes/colour changers and
lime removers suitable for machine
wash. Always follow the instructions
on the packaging.
Suitable for
drier
Do not dry
with drier
Dry
Dry on a
hanger
horizontally
Hang without Can be ironed
spinning
Can be
Do not iron
with hot iron ironed with
warm iron
•
•
Wash trousers and delicate clothes
turned inside out.
Keep laundry items made of Angora
wool in the freezer for a few hours
before washing. This will reduce
pilling.
Preparing clothes for washing
Laundry items with metal attachments
such as, bras, belt buckles and metal
buttons will damage the machine.
Remove metal attachments or place the
items in a clothing bag, pillow case, or
something similar.
Correct load capacity
•
The maximum load capacity
depends on the type of laundry, the
degree of soiling and the washing
programme you wish to use.
C The machine adjusts the amount of
water according to the amount of
laundry placed inside.
C Please follow the information in
the "Programme Selection Table".
Washing results will degrade when
the machine is overloaded.
11 - EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Following weights are given as
examples.
Detergent, softener and other clean-
ing agents
Add detergent and softener before
starting the washing programme.
Never open the detergent dispenser
drawer while the washing programme is
running!
When using a programme without
pre-wash, no detergent should be
put into the pre-wash compartment
(Compartment no. I).
A programme without pre-wash should
be selected if a detergent bag or a
dispensing ball is going to be used.
You can place the detergent bag or
the dispensing ball directly among the
laundry in your machine.
Laundry type
Bathrobe
Napkin
Weight (gr.)
1200
100
700
500
200
250
200
200
100
600
200
500
100
Duvet cover
Bed Sheet
Pillowcase
Tablecloth
Towel
Evening gown
Underclothing
Men’s overalls
Men’s shirt
Men’s pyjamas
Blouse
Choosing the detergent type
The type of detergent to be used
depends on the type and colour of
fabric.
Loading door
The door is locked during programme
operation. The door can be opened after
some time following the programme
end.
•
•
•
Use different detergents for coloured
and white clothes.
Wash woolens with a special
detergent specifically for woolens.
Use only detergents manufactured
specifically for automatic washing
machines.
•
•
Open the door.
Place laundry items loosely in the
machine.
•
Push the door until it clicks into
place tightly. Ensure that no items
are caught in the door.
Detergent quantity
The amount of washing detergent to
be used depends on the amount of
laundry, the degree of soiling and water
hardness.
Detergents and softeners
Detergent drawer
The detergent drawer is composed of
three compartments:
•
Do not use amounts exceeding
the quantities recommended on
the package to avoid problems
of excessive foam, poor rinsing,
financial savings and finally,
environmental protection.
The detergent dispenser may be in two
different types according to the model of
your machine.
- (I) for prewash
- (II) for main wash
- (III) siphon
•
•
Use small amounts of detergent at a
suitable measure for small amounts
of laundry or for only slightly soiled
laundry.
Use exact measures for highly
concentrated detergents.
– ( ) for softener
12 - EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Eliminating lime formation
Detergent
•
When required, use only appropriate
lime removers developed specifically
for washing machines and always
follow the instructions on the
package.
quantity
for prewashing
for main washing
1/2 measure
1 measure
an additional 1/2
measure
with hard water
Softener
Put the softener into the softener
compartment of the detergent
dispenser.
•
Use the proportions recommended
on the packet.
•
Never exceed the (> max <) level
marking; otherwise, the softener will
be wasted without being used.
If the softener has lost its fluidity,
dilute dense softener with water
before placing it in the detergent
drawer.
•
Liquid detergent
When using liquid or gel washing
detergents, please note the following:
•
•
The liquid detergent may leave
stains on your laundry if time delay
feature is selected.
Do not use liquid detergent if you
want to wash using the time delay
feature.
•
•
Do not use liquid detergent for the
main wash in a cycle with pre-wash.
Use the detergent manufacturer’s
measuring cup and follow the
instructions on the package.
Starch
•
Add liquid starch, powder starch
or the fabric dye into the softener
compartment as instructed on the
package.
•
•
Never use fabric softener and starch
together in the same washing cycle.
Wipe the inside of the drum after
using starch.
13 - EN
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Selecting a Program and Operating Your Machine
Control panel
Figure 2
7
13
9
12
14
8
11
10
7 - Spin Speed Adjustment Button
8 - Time Delaying Button (+/-)
9 - Temperature Adjustment Button
10- Start/Pause/Cancel Button
11- Auxiliary Function Buttons
12 - Program Selection Knob
13 - Display
14 - On/Off Button
14 - EN
Download from Www.Somanuals.com. All Manuals Search And Download.
appear. Press "Start/Pause/Cancel"
button (Figure 2-10) to start the
program.
Display symbols
Figure 3
Main programs
Depending on the type of textile, the
following main programs are available:
Each of these main programs comprise
of a complete washing process,
including washing, rinsing and, if
required, spin cycles.
13.a - Spin Speed Indicator
13.b - Temperature Indicator
13.c - Spin Symbol
A When selecting the program you are
going to use, always consider type
of fabric, color, degree of soiling and
permissible water temperature.
A Always select the lowest required
temperature. Higher temperature
means higher power consumption.
C For further program details, see
"Program Selection Table"
13.d - Temperature Symbol
13.e - Remaining Time and
Delaying Time Indicator
13.f - Program Indicator
Symbols (pre-wash/main wash/
rinse/softener/spin)
13.g - Economy Symbol
13.h - Time Delaying Symbol
13.i - Door Locked Symbol
13.j - Start Symbol
• Pamuklu (Cottons)
13.k - Standby Symbol
13.l - Auxiliary Function
Symbols
You can wash your durable clothes
with this program. Your laundry will
be washed with vigorous washing
movements during a longer washing
cycle. It is recommended for your
cotton items (such as bed sheets,
duvet and pillowcase sets, bathrobes,
underclothing, etc.).
Turning the machine on
Plug in your machine. Turn the tap on
completely. Check if the hoses are
connected tightly. Place the laundry
in the machine. Add detergent and
softener. Press the “On/Off” button
(Figure 2-14).
• Sentetik (Synthetics)
You can wash your less durable clothes
on this program. Gentler washing
movements and a shorter washing cycle
is used compared to the “Cottons”
program. It is recommended for your
synthetic clothes (such as shirts,
blouses, synthetic/cotton blended
garments, etc.). For curtains and
lace, the “Synthetic 40” program with
pre-wash and anti-creasing functions
selected is recommended. Detergent
should not be put in the pre-wash
compartment. Less detergent should be
Program selection
Select the appropriate program from
the program table according to type,
amount and degree of soiling of the
laundry and washing temperatures.
Turn the Program Selection Knob (Figure
2-12) to the program mode that you
wish to wash your laundry.
The recommended temperature and
spin speed for the selected program
15 - EN
Download from Www.Somanuals.com. All Manuals Search And Download.
put in the main wash compartment as
loose knit fabrics (lace) foam too much
due to its meshed structure.
• Mix 40
You can use this program to wash
cottons and synthetics together. There
is no need to sort them.
• Intensive
• Yünlü (Woollens)
You can wash your machine-washable
woolen garments on this program. Wash You can wash your durable and heavily
by selecting the proper temperature
according to the labels of your clothes.
It is recommended to use appropriate
detergents for woolens.
soiled clothes on this program. In this
program, your clothes will be washed
for a longer time and an extra rinse cycle
will be made compared to the “Cottons”
program. You can use it for your heavily
soiled clothes that you wish to be rinsed
gently.
Additional programs
For special cases, there are also extra
programs available:
• Shirts
You can use this program to wash the
shirts made of cotton, synthetic and
synthetic blended fabrics.
C Additional programs may differ
according to the model of your
machine.
• Perde (Curtain)
• Bebek
You can use this program to wash
your lace and curtains. It provides less
creasing on lace and curtains thanks to
the special spin profile of the program.
Less detergent should be put in the
main wash compartment as loose knit
fabrics (lace) foam too much due to its
meshed structure.
Never put detergent in the prewash
compartment. Prewash is applied to
remove the particles (such as dust or
soot) on the lace/curtains, which can be
removed easily.
Increased hygiene is provided by a
longer heating period and an additional
rinse cycle. It is recommended for baby
clothes and clothes worn by allergic
people.
• Elde Yıkama (Hand wash)
You can wash your woolen/delicate
clothes that bear “not machine-
washable” labels for which hand wash
is recommended on this program. It
washes the laundry with very tender
washing movements without damaging
your clothes.
C It is recommended to use special
detergents for curtains in this
program.
• Express
This program is used to wash lightly
soiled and unstained cotton garments in
a short time.
• Express 14
Special programs
You can use this program to quickly
wash a small number of lightly soiled
and unstained cotton garments. E.g.:
bathrobes, duvet covers, sport wear,
daily clothes and etc. used only once.
• Darkcare
For specific applications, select any of
the following programs:
• Durulama (Rinse)
This program is used when you want to
rinse or starch separately.
• Sıkma+Pompa (Spin + Drain)
This program spins with maximum
possible rpm in the default setting after
the water drains from the machine.
C Use a lower spin speed for delicate
laundries.
Use this programme to wash your
dark coloured laundry, or the coloured
laundry that you do not want them get
faded. This programme washes your
laundry with low mechanical movements
and at low temperature. We recommend
you to use liquid detergent or woolen
shampoo for dark coloured laundry.
Temperature selection
Whenever a new program is selected,
the temperature anticipated for that
16 - EN
Download from Www.Somanuals.com. All Manuals Search And Download.
program appears on the temperature
indicator (13b).
Economy Symbol
To change the temperature, press
the temperature button (Figure
2-9). Temperature decreases in 10°
increments.
Shows energy saving programs and
temperature selections.
As "Intensive" and "Hygiene" programs
are long programs with higher
temperature selections to ensure
hygiene, “Economy” Symbol (Figure
3-13g) will not light up.
Cold selection is shown with “-” symbol.
e
When the “Temperature” button is
pressed after Cold is selected, the
maximum temperature of the program
you have selected will be displayed.
To decrease the temperature, press the
“Temperature” button again.
Spin Speed selection
Whenever a new program is selected,
the maximum spin speed of the selected
program is displayed on the spin speed
indicator (Figure 3-13a).
To decrease the spin speed, press
the “Spin” button (Figure 2-7). Spin
speed decreases gradually. Then, rinse
hold and no spin options are shown
respectively.
Rinse hold is shown with “ ” and no
spin is shown with “ ” symbols.
Normally soiled, white
cottons and linens. (Ex.:
90˚C
coffee table covers,
tablecloths, towels, bed
sheets)
Normally soiled, fade proof
colored linens, cottons
or synthetic clothes
(Ex.: shirts, nightgowns,
pajamas) and lightly soiled
white linen clothes (Ex.:
underwear)
e
60˚C
Blended clothes including
synthetics and woolens as
well as delicates.
40˚C
30˚C Cold
If you are not going to unload your
clothes immediately after the cycle, you
may use rinse hold function in order to
prevent your clothes become wrinkled
when there is no water in the machine.
With this function, your laundry is kept
in the final rinsing water. If you want to
spin your laundry after the rinse hold
function:
-
Adjust the spin speed.
-
Press “Start/Pause/Cancel” button.
Program resumes. Your machine
drains the water and spins your
laundry.
You can use no spin function in order to
drain the water without spinning at the
end of the program.
17 - EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Program and consumption table
EN
Auxiliary functions
Programme (°C)
Pamuklu
Pamuklu
Pamuklu
Yorgan
Bebek
90
60**
40
40
90
60
40
40
40
40
8
8
8
-
61
59
72
60
73
55
55
55
56
67
40
70
70
80
35
2.70 1600 •
1.36 1600 •
0.75 1600 •
0.60 1000
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
90-Cold
90-Cold
90-Cold
60-40
8
4
4
4
2
2
1.5
8
8
8
2
2.70 1600
*
•
•
•
•
•
•
90-30
Sentetik
Sentetik
Mix 40
Yünlü
1.00 1000 •
0.52 1000 •
0.62 1000 •
0.30 1000
•
•
•
•
•
•
•
*
•
•
•
•
•
•
•
60-Cold
60-Cold
40-Cold
40-Cold
40-Cold
30-Cold
90-Cold
90-Cold
90-Cold
30-Cold
Perde
0.50 800
0.25 1000
2.00 1400
1.15 1400
0.20 1400
0.10 1400
*
*
Elde Yıkama 30
Express
Express
Express
90
60
30
•
•
•
•
•
•
•
•
Express 14 30
• : Selectable
* : Automatically selected, not cancellable.
** : Energy Label program (EN 60456)
*** If maximum spin speed of your machine is lower, selection may be made until
maximum spin speed.
- : See program description for maximum load.
C The auxiliary functions in the table vary according to the model of your machine.
C Water and power consumption and program duration differ from the table
subject to changes in water pressure, water hardness and temperature, ambient
temperature, type and amount of laundry, selection of auxiliary functions, and
changes in supply voltage.
C Program duration will be displayed on the screen of your machine according to
your selection.
18 - EN
Download from Www.Somanuals.com. All Manuals Search And Download.
• Hızlı Yıkama (Quick Wash)
With this function (11b), the wash time is
shortened. "F2” symbol lights up on the
display.
Auxiliary functions
Auxiliary Function Selection Buttons
•
Use this function for smaller
amounts or slightly soiled laundries.
• Rinse Plus
When this function (11c) is selected,
washing and rinsing is performed with
plenty of water. "F3” symbol lights up on
the display.
• İlave Su (Plus water)
���
��� ��� ���
When this function is selected, washing
and rinsing is made with plenty of water
in “Cottons”, “Synthetics”, “Delicates”
and “Woolens” programs.
•
Depending on the program, you can
select the desired auxiliary function
by pressing the buttons 11a, 11b,
11c,11d.
Select the required auxiliary
functions before starting the
program.
Some combinations cannot be
selected together. Ex.: Pre-wash
(Figure 2-11a) and Quick Wash
(Figure 2-11b).
Symbol of the selected auxiliary
function (Figure 3-13l) will light up.
C Use this function for delicate
laundries that crease easily.
C Whenever you select this auxiliary
function, load your machine with half
of the maximum laundry specified in
the program table.
•
•
• Kırışık Azaltma (Anti-Creasing)
With this function (11d), drum
movement will be lessened to prevent
creasing and spinning speed is limited.
In addition, washing is carried out at a
higher water level. "F4” symbol lights up
on the display.
•
Auxiliary function selection
If an auxiliary function that should not
be selected together with a previously
selected function is chosen, the first
selected function will be cancelled and
the last auxiliary function selection will
remain active.
Ex.: If you want to select pre-wash first
and then quick wash, pre-wash will be
cancelled and quick wash will remain
active.
Auxiliary function that is not compatible
with the program cannot be selected.
(see, “Program Selection Table”)
• Ön Yıkama (Prewash)
When you select this function (11a), the
display will indicate "F1" symbol.
•
Use this function for delicate
laundries that crease easily.
C Whenever you select this auxiliary
function, load your machine with half
of the maximum laundry specified in
the program table.
Time display
The display shows the time remaining
for the program to complete while a
program is running. Time is displayed in
hours and minutes as “01:30”.
•
A pre-wash is only worthwhile for
heavily soiled laundry. Without
pre-wash you save energy, water,
detergent and time.
Pre-wash without detergent is
recommended for lace and curtains.
•
19 - EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Time delay
will fade. The Start symbol (Figure
3-13j) will light up.
With the “Time delay” function you can
delay the program start up to 24 hours.
Setting can be made in intervals of 30
minutes.
4. The “:” in the middle of the displayed
time delay will start to flash.
1. Open the loading door, place the
laundry inside and fill detergent
drawer.
2. Set the washing program,
temperature, spin speed and,
if required, select the auxiliary
functions.
3. Press “Time delaying” buttons
“+” and “-” (Figure 2-8) to set
your desired time delay. The Time
delaying symbol (Figure 3-13h) will
flash.
Canceling the time delay
If you want to cancel the time delay
countdown and start the program
immediately:
1. Press “Start/Pause/Cancel” button
(Figure 2-10). The “:” in the middle
of the displayed time delay will stop
flashing.
2. Start symbol (Figure 3-13j) will fade.
The standby symbol (Figure 3-13k)
and the time delaying symbol (Figure
3-13h) will flash.
4. Press “Start/Pause/Cancel” button
(Figure 2-10). Then the time delay
starts to count down. The Time
delaying symbol (Figure 3-13h) will
light up. The Start symbol (Figure
3-13j) will light up.
3. Press time delaying button “-”
(Figure 2-8) to decrease the desired
time delay. Program duration after
30 minutes shall be displayed.
4. Press Start/Pause/Cancel Button
(Figure 2-10) to start the program.
The “:” in the middle of the displayed
time delay will start to flash.
Starting the Program
•
More laundry may be loaded or
taken out during the time delay
period. At the end of the time delay
countdown process, time delaying
symbol (Figure 3-13h) fades and
the washing starts as the program
duration is displayed.
1. Press Start/Pause/Cancel button
(Figure 2-10) to start the program.
2. The start symbol (Figure 3-13j)
which indicates that the program
has started will light up.
3. The door locks and the door locked
symbol (Figure 3-13i) will light up.
4. The Symbol of the relevant step
(prewash, main wash, rinse, softener
and spin) that the program has
started from will light up (Figure
3-13f).
Changing the delay time
If you want to change the time during
the countdown:
1. Press “Start/Pause/Cancel” button
(Figure 2-10). “ : “ in the middle of
the screen will stop flashing. The
Standby symbol (Figure 3-13k) will
light up. The Time delaying symbol
(Figure 3-13h) will flash. The Start
Symbol (Figure 3-13j) will fade.
2. Press “Time delaying” buttons “+” or
“-” (Figure 2-8) to set your desired
time delay.
3. Press “Start/Pause/Cancel” button
(Figure 2-10). The Time delaying
symbol (Figure 3-13h) will light up.
The Standby symbol (Figure 3-13k)
Progress of program
The progress of a running program is
shown through a number of symbols on
the screen.
•
At the beginning of each program
step, the relevant symbol in the
series of symbols will light up and
thus, at the end of the program,
all symbols will remain lit up. The
symbol that lights up at the far right
of the series of symbols indicates
the step that is being carried out.
20 - EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-wash
When "prewash" auxiliary function is
selected, prewash symbol will light up to
indicate the beginning of prewash step.
Main wash
Main wash symbol will light up to
indicate that the main wash cycle has
started.
Selecting or canceling an auxiliary
function in pause mode
Auxiliary functions can be cancelled or
selected in accordance with the step the
program is at.
Rinse
Rinse symbol lights up at the beginning
of the rinse step.
Softener
Softener symbol lights up at the
beginning of softener step.
Spin
Spin symbol will light up at the
beginning of the final spin, during “Spin”
and “Pump” special programs.
Adding/removing laundry in pause
mode
The door can be opened if the water
level is suitable. The door locked symbol
(Figure 3-13i) will light up until the door
is suitable for opening. This symbol will
fade out as soon as the door is allowed
to open. Laundry may be added / taken
out by opening the door.
•
If the machine is not spinning, the
program may be in rinse hold mode
or the automatic spin correction
system has been activated due
to an excessive unbalanced
distribution of laundry in the
machine.
Door lock
The Door Locked Symbol (Figure 3-13i)
lights up when the loading door is
locked. This symbol will flash until the
door is allowed to open. Do not force
the door at this stage. This symbol will
fade out as soon as the door is allowed
to open. You may open the door after
the symbol fades out.
Changing the selections after
the program has started
The selected spin speed and program
temperature fade out. An empty frame
appears.
When the “Program selection” button is
brought to the appropriate position, rpm Child-proof lock
and temperature data reappear.
Protect the appliance from being
tampered by children by means of the
child-proof lock. In this case, no change
can be made in the running program.
C Your machine can be turned on
and off with On/Off button while
the child-proof lock is activated. In
this case, your machine will resume
its program with child-proof lock
activated.
The machine is switched to child-lock
by pressing the 2nd and 4th auxiliary
functions for 3 sec. “C:on” (Child-proof
lock is activated) label appears on the
display.
Switching the machine to
standby mode
The machine is switched to standby
mode by pressing “Start/Pause/Cancel”
button (Figure 2-10) momentarily. The
Standby symbol (Figure 3-13k) which
indicates the machine is in standby
mode lights up and the start symbol
(Figure 3-13j) that shows the program
has started and is still continuing fades
out.
21 - EN
Download from Www.Somanuals.com. All Manuals Search And Download.
If you wish to spin when the machine is
in this mode:
Adjust the spin speed. Press “Start/
Pause/Cancel” button (Figure 2-10).
The program continues, pumps out the
water and spins. The Standby Symbol
(Figure 3-13k) fades out and Start
Symbol (Figure 3-13j) lights up.
If you want to discharge the water only
without spinning:
Press “Start/Pause/Cancel” button
(Figure 2-10). The Standby symbol
(Figure 3-13k) will fade. The Start
symbol (Figure 3-13j) will light up. The
program continues and only drains the
water.
The same symbol will also be displayed
whenever any button is pressed while
the machine is child-locked.
To deactivate the child-proof lock,
press the 2nd and 4th auxiliary function
buttons for 3 sec.
“C:OFF” (Child-proof lock is deactivated)
label appears on the screen.
End of program
When the program is finished, the
symbols of the relevant steps will remain
lit up and the auxiliary function, spin and
temperature data selected at the start-
up of the program will remain selected.
“End” will appear on the display.
Ending the program through
canceling
“Start/Pause/Cancel” button (Figure
2-10) is pressed for 3 seconds to cancel
the program. Start symbol (Figure
3-13j) will flash during cancellation.
After cancellation, the symbol of the
corresponding step at which the
cancellation was made will remain lit and
“End” will appear on the screen.
Program in rinse hold mode
•
This process is shown with the
flashing Spin Symbol (Figure 3-13c)
and the lit up Standby Symbol
(Figure 3-13k).
22 - EN
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Quick instructions for daily use
Preparation
adding more laundry during a future
step only if the water level is low
enough to open the loading door or
if the temperature in the machine is
low).
1. Turn the tap on completely. Check
that the hose is connected tightly.
2. Place the laundry in the machine.
3. Add detergent and softener.
In order to add laundry after the
start-up of the programme:
Starting
1. Press “Start/Pause/Cancel” button.
2. Open the loading door and put in
more laundry.
3. Close the loading door.
4. Press “Start/Pause/Cancel” button.
1. Press the “On/Off” button.
2. Select the programme and the
temperature.
3. If desired (according to your
machine’s model):
–
–
–
select any auxiliary function,
adjust the spin speed,
set the time delay,
Programme is in rinse hold mode
C This process is shown with the
flashing spin symbol and the
standby symbol which is lit up.
If you wish to spin when the machine is
in this mode:
4. Close the loading door.
5. Press “Start/Pause/Cancel” button.
The display shows the time remaining
for the programme to complete if time
delay is not set.
The display shows the time remaining
for the programme to start if the time
delay is set.
6. Check if the Door Locked Symbol
lights up on the screen.
The Door Locked Symbol (Figure 3-2i)
will light up if time delay is not set.
The Door Locked Symbol (Figure 3-2i)
will fade if time delay is set.
1. Adjust the spin speed.
2. Press “Start/Pause/Cancel” button.
The programme continues, pumps
out the water and spins.
3. The standby symbol fades out and
the start symbol lights up.
If you want to discharge the water
without spinning:
1. Press “Start/Pause/Cancel” button.
2. The standby symbol fades out and
the start symbol lights up.
3. The programme continues and only
pumps out the water.
Cancelling a programme
1. Press and hold the “Start/Pause/
Cancel” button for about 3 seconds;
the Start symbol will start flashing.
2. The machine can discharge all
the water or can take in water for
3 times at most to cool down the
clothes and complete discharging
process.
Re-spinning the laundry
The control system for an unbalanced
load can pause the spinning in cases
when the distribution of the laundry in
the drum is not balanced.
If you want to re-spin the clothes:
1. Distribute the laundry in your
machine for a balanced load.
2. Select the spin programme.
3. Adjust the spin speed.
Adding more laundry
•
This is only possible under the
following conditions:
during time delay,
–
C You may add or remove laundry
during the time delay (until the
After the programme is finished
Programme indicator symbols on
the screen will remain lit after the
programme is finished. “End” will appear
programme starts). At the beginning
of a washing cycle (machine allows
23 - EN
Download from Www.Somanuals.com. All Manuals Search And Download.
on the screen.
1. Open the loading door and take out
the laundry when the door locked
symbol on the display fades out.
2. Press the “On/Off” button.
3. Turn the water tap off.
4. Remove any folds in the rubber seal
on the loading door and check for
debris.
5. Leave the loading door and
detergent drawer open to dry.
24 - EN
Download from Www.Somanuals.com. All Manuals Search And Download.
7 Cleaning and care
machine can cause rust stains. In
such cases:
Clean the drum with a stainless steel
cleaning agent. Never use steel wool
or wire wool.
Detergent drawer
Remove any powder residue buildup in
the drawer. To do this;
1. Press the dotted point on the
siphon in the softener compartment
and pull towards you until the
compartment is removed from the
machine.
Outer cabinet and control
panel
When necessary:
•
Wipe the exterior panels of your
machine with soapy water or mild
detergent. Dry it with a soft cloth.
Use only a soft and damp cloth to
clean the control panel.
•
C Never use a sponge or scrubbing
material. These will damage the
painted and plastic parts.
C If more than a normal amount of
water and softener mixture starts to
gather in the softener compartment,
the siphon must be cleaned.
2. Wash the dispenser drawer
and the siphon with plenty of
lukewarm water in a washbasin.
Wear protective gloves or use an
appropriate brush to avoid touching
the residues in the drawer when
cleaning.
Inlet water filters
There is a filter at the end of each
water intake valve at the back side of
the machine and also at the end of
each water intake hose where they
are connected to the tap. These filters
prevent the foreign substances and dirt
in the water to enter into the machine.
Filters should be cleaned as they get
dirty.
3. Replace the drawer into its housing
after cleaning. Check if the siphon
is in its original location.
The door and the drum
After each wash:
•
Check if there are any foreign
substances in the drum.
Open the hole in the bellow with the
aid of a toothpick if it is clogged.
•
•
•
Close the taps.
Remove the nuts of the water intake
hoses to clean the surfaces of the
filters on the water intake valves with
an appropriate brush.
•
If the filters are very dirty, you can
pull them out by means of pliers and
C Foreign metal substances in your
25 - EN
Download from Www.Somanuals.com. All Manuals Search And Download.
clean them.
•
•
Take out the filters on the flat
ends of the water intake hoses
together with the gaskets and clean
thoroughly under streaming water.
Replace the gaskets and filters
carefully and tighten the hose nuts
by hand.
If it is composed of one piece, hold it
from both sides and open it by pulling
out.
C You can remove the filter cover
by slightly pushing the kick plate
downwards with a screwdriver,
through the gap above the filter
cover.
Draining any remaining water
and cleaning the pump filter
Filter system in your machine prevents
solid items such as buttons, coins and
fabric fibers clogging the pump propeller
during discharging of the washing
water. Thus, a good water discharger is
achieved and the pump life is extended.
•
If your machine fails to drain the
water, the pump filter may be
clogged. You may have to clean
it every 2 years or whenever it is
blocked plugged. Water must be
drained off to clean the pump filter.
In addition, water may have to be
drained off completely in the
following cases:
3- An emergency drain hose is supplied
with some of our models. Others are not
supplied with this item.
•
before transporting the machine
(e.g. when moving house)
•
when there is the danger of frost
If your product is supplied with an
emergency drain hose, do the following
as shown in the figure below:
In order to clean the dirty filter and
discharge the water;
1- Disconnect or unplug the machine
from the power supply.
A There may be water at 90°C in the
machine. Therefore, the filter must
be cleaned only after the inside
water is cooled down to avoid
hazard of scalding.
2- Open the filter cap. The filter cap
may be composed of one or two pieces
according to the model of your machine.
If it is composed of two pieces, press
the tab on the filter cap downwards and
pull the piece out towards yourself.
•
•
Pull out the pump outlet hose from
its housing.
Place a large container at the end of
the hose. Drain the water off into the
container by pulling out the plug at
the end of the hose. If the amount
of water to be drained off is greater
than the volume of the container,
replace the plug, pour the water out,
26 - EN
Download from Www.Somanuals.com. All Manuals Search And Download.
then resume the draining process.
After draining process is completed,
replace the plug into the end of the
hose and fit the hose back into its
place.
•
If your product is not supplied with an
emergency drain hose, do the following
as shown in the figure below:
•
•
Place a large container in front of the
filter to receive water flowing from
the filter.
Loosen pump filter (anticlockwise)
until water starts to flow out of it.
Direct the flowing water into the
container you have placed in front
of the filter. You can use a piece of
cloth to absorb any spilled water.
When there is no water left, turn
the pump filter until it is completely
loose and remove it.
Clean any residues inside the filter
as well as fibers, if any, around the
propeller region.
If your product has a water jet
feature, be sure to fit the filter into
its housing in the pump. Never force
the filter while replacing it into its
housing. Fit the filter fully into its
housing; otherwise, water may leak
from the filter cap.
•
•
•
4- Close the filter cap.
Close the two-piece filter cap of your
product by pushing the tab on it.
Close the one-piece filter cap of your
product by fitting the tabs on the bottom
into their positions and pushing the
upper part of it.
27 - EN
Download from Www.Somanuals.com. All Manuals Search And Download.
8 Solution suggestions for problems
Cause
Explanation / Suggestion
Programme cannot be started or selected.
Machine may have switched to
self protection mode due to an
infrastructure problem (such as line
voltage, water pressure, etc.).
Bring your machine to factory settings by turning
the programme selection knob. (see, Ending the
programme through Cancelling)
Water in the machine.
There may be some water in your
machine when you receive it. This is
from the quality control process and is
normal.
It is not harmful to your machine.
There is water coming from the bottom of the machine.
- Make sure that the seals of the water inlet hoses
are securely fitted.
There might be problems with hoses or
the pump filter.
- Tightly attach the drain hose to the tap.
- Make sure that the pump filter is completely
closed.
Machine does not fill with water
- Tap may be turned off.
- Open the inlet water taps fully.
- Flatten the water intake hose.
- Clean the water intake filter.
- Close the loading door.
- Water inlet hose might be bent.
- Water inlet filter might be clogged.
- The loading door may be ajar.
Machine does not discharge water.
- Water outlet hose might be clogged
or twisted.
- Pump filter may be clogged.
- Clean or flatten the hose.
- Clean the pump filter.
Machine vibrates or shakes.
- Machine feet might not be adjusted.
- Transportation safety bolts might have
not been removed.
- Adjust the machine feet.
- There may be a small amount of
laundry in the machine.
- Remove the transportation safety bolts.
- Add more laundry to the machine.
- Reduce the amount of laundry in the machine or
balance the load by hand.
- The machine may be overloaded
or the clothes may be distributed
unevenly.
- Ensure that nothing touches the machine.
- There machine might be touching a
solid surface.
Machine stops shortly after the programme starts.
Machine can stop temporarily due to
low voltage.
It will resume operating when the voltage is back to
the normal level.
The water being taken in is directly discharged.
Connect the water draining hose as described in
the operation manual.
Improper position of the drain hose.
No water can be seen in the machine during washing.
This is not a problem. The water level
is not visible from the outside of the
machine.
28 - EN
Download from Www.Somanuals.com. All Manuals Search And Download.
The door is jammed.
- Water level might be above the lower
level of the door.
- Machine might be heating up the
water or it may be at the spinning
cycle.
- Due to an electrical mechanism,
the door can only be opened a few
minutes after the programme has
stopped.
- Run either the “Pump” or “Spin” programme.
- Wait until the process is over.
- Wait until the process is over.
Machine fills with water when a process is cancelled.
For safety reasons, water should be cycled in and
out a couple times.
Inside of machine may be hot.
It continuously spins. Remaining time does not count down. (On models with display)
- The automatic spin correction system might have
been activated due to the unbalanced distribution
of the laundry in the drum.
- The laundry in the drum may be clustered
There may be an imbalance of laundry
(bundled laundry in a bag). Laundry should be
in the machine.
rearranged and re-spun.
- No spinning is performed when the laundry is
not evenly distributed in the drum to prevent any
damage to the machine and to its environment.
Washing time takes longer than the time specified in the manual
- The machine will wait until there is sufficient
amount of water, which will lengthen the washing
time to avoid poor washing results due to
insufficient water.
- Washing time is extended to avoid poor washing
results when the supply voltage is low.
- Water pressure may be low.
- Supply voltage may be low.
- Input temperature of water may be
low.
- Cycle time is extended to heat up the water when
the input water is cold. Also, washing time can be
lengthened to avoid poor washing results.
- The automatic spin correction system might have
been activated due to the unbalanced distribution
of the laundry in the drum.
- There may be an imbalance of
laundry in the machine.
- Number of rinses and/or amount of
rinse water might have increased.
- The laundry in the drum may be clustered
(bundled laundry in a bag).
- Laundry should be rearranged and re-spun.
- No spinning is performed when the laundry is
not evenly distributed in the drum to prevent any
damage to the machine and to its environment.
- Water amount is increased to obtain a better
rinse and a rinse cycle is added when necessary.
29 - EN
Download from Www.Somanuals.com. All Manuals Search And Download.
It continuously washes. Remaining time does not count down.
- The machine will wait until there is sufficient
In the case of a paused countdown
while taking in water:
amount of water to avoid poor washing results due
to lack of water. Then the timer will start to count
down.
- Timer will not countdown until the
machine is filled with the correct
amount of water. (On models with
display)
- Time will not count down until the selected
temperature for the programme is attained.
- The automatic spin correction system might have
been activated due to the unbalanced distribution
of the laundry in the drum.
- The laundry in the drum may be clustered
(bundled laundry in a bag). Laundry should be
rearranged and re-spun.
- No spinning is performed when the laundry is
not evenly distributed in the drum to prevent any
damage to the machine and to its environment.
- Time might have gotten stuck during
heating step. (On models with display)
In the case of a paused countdown at
the spinning step:
There may be an imbalance of laundry
in the machine. (On models with
display)
It did not spin.
- The automatic spin correction system might have
been activated due to the unbalanced distribution
of the laundry in the drum.
- There may be an imbalance of
laundry in the machine. Therefore,
the programme might have been
completed without spinning.
- The machine will not spin if the water
has not completely drained.
- The laundry in the drum may be clustered
(bundled laundry in a bag). Laundry should be
rearranged and re-spun.
- No spinning is performed when the laundry is
not evenly distributed in the drum to prevent any
damage to the machine and to its environment.
- Check the filter.
- Check the drain hose.
Washing performance is poor: Laundry turns grey
- Using insufficient amount of
detergent for a long time,
- Washing at low temperatures for a
long time,
- Use the recommended amount of detergent
appropriate for water hardness and the laundry.
- Select the proper temperature for the laundry to
be washed.
- Using insufficient amount of
- If the water hardness is high, using an insufficient
detergent for hard waters (soil can stick amount of detergent can cause laundry to turn
to the laundry),
grey over time.
- Using excessive amount of detergent - It is difficult to eliminate such greyness once it
(detergent can stick to the laundry).
occurs.
Washing performance is poor: Stain could not be removed, not cleaned. Laundry could not
be whitened.
- Insufficient amount of detergent used.
- Use recommended amount of detergent
- Excessive laundry loaded into
appropriate for the laundry.
machine
- Do not load the machine in excess.
- Wrong programme and temperature
- Select the proper programme and temperature
might have been selected.
for the laundry to be washed.
- Improper detergent may have been
- Put the detergent in the correct compartment.
used.
- Do not mix detergent with bleaching agents.
- Wrong type of detergent used.
30 - EN
Download from Www.Somanuals.com. All Manuals Search And Download.
- Washing performance is poor: Oily stains appear on laundry.
- Washing performance is poor: Bad odour
- Such odours and bacteria layers are formed on
the drum as a result of continuous washing at
lower temperatures and/or in short programmes.
- Oily accumulations on the drum may - Leave the detergent dispenser drawer as well
have stuck to the laundry.
as the loading door of the machine ajar after each
- Oily accumulations on the drum may washing. Thus, a humid environment favorable for
have stuck to the laundry.
bacteria cannot be created inside the machine.
- Machine must be operated empty either at
60°C or 90°C programme with detergent every 6
months.
Colour of the clothes faded.
- Do not load the machine in excess
- Store detergent in a closed and dry location.
- Do not keep them under high temperatures.
- Select the proper programme and temperature
according to the type and soiling degree of the
laundry.
- Excessive laundry loaded into
machine.
- Detergent may have gotten damp.
- A higher temperature might have
been selected.
It does not rinse well.
- Store detergent in a closed and dry location. Do
not keep them under high temperatures.
- If detergent is put in the prewash compartment
although prewash cycle is not selected, machine
can take this detergent during rinsing or softener
- The amount, brand and storage
conditions of the detergent used might step.
not be appropriate.
- Check the filter.
- Detergent might have been put in the - Check the drain hose.
wrong compartment.
- There may be an imbalance of laundry in the
- Machine filter may be clogged.
- Drain hose may be folded.
- Intermediate spins may be skipped.
machine.
- The laundry in the drum may be clustered
(bundled laundry in a bag). Laundry should be
rearranged and re-spun.
- No spinning is performed when the laundry is
not evenly distributed in the drum to prevent any
damage to the machine and to its environment.
Clothes stiffened.
- If the water hardness is higher, using insufficient
amount of detergent can cause the laundry to
become stiff in time. Use appropriate amount of
- Insufficient amount of detergent used. detergent according to the water hardness.
- The detergent may have been
placed into the wrong compartment;
the detergent may be mixed with the
softener.
- If detergent is put in the prewash compartment
although prewash cycle is not selected, machine
can take this detergent during rinsing or softener
step.
- Do not mix the softener with detergent when
putting in the compartment.
- Wash and clean the drawer with hot water.
31 - EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Clothes do not smell like the softener.
- If the water hardness is higher, using insufficient
amount of detergent can cause the laundry to
become stiff in time. Use appropriate amount of
detergent according to the water hardness.
- If detergent is put in the prewash compartment
although prewash cycle is not selected, machine
can take this detergent during rinsing or softener
step.
- Insufficient amount of detergent used.
- The detergent was placed into the
wrong compartment; the detergent
was mixed with the softener.
Do not mix the softener with detergent when
putting in the compartment.
Wash and clean the drawer with hot water.
Detergent residue in the dispensing drawer.
- Dry the detergent drawer before putting in
- Detergent may have been put in wet
dispenser drawer.
detergent.
- Store detergent in a closed and dry location.
- Do not keep them under high temperatures.
- The detergent dispenser outlet (holes) may have
a problem.
- There might be problems with the detergent
dispenser valves.
- Do not mix the softener with detergent when
putting in the compartment.
- Detergent may have gotten damp.
- Water pressure might be low
- The detergent in the main wash
compartment might have gotten wet
while taking in the prewash water..
- Detergent might be mixed with the
bleaching agent.
There is detergent left on the laundry.
- Excessive laundry loaded into
machine.
- Do not load the machine in excess.
- Wrong programme and temperature - Select the proper programme and temperature
might have been selected.
- Wrong detergent may have been
used.
for the laundry to be washed.
- Use wool detergents for woolens.
There is too much foam
.
- Use only automatic washing machine detergents
in your washing machine.
- You may not be using proper
detergent for automatic washing
machines.
- Use only sufficient amount of detergent.
- Use only sufficient amount of detergent.
- Store detergent in a closed and dry location.
- Do not store in excessively hot places.
- Use smaller amounts of detergent for lace items.
- If you put detergent in the prewash
- Excessive amount of detergent may
have been used.
- Too much detergent may have been
used for a small amount of lightly soiled
laundry.
compartment although you have not selected
a prewash cycle, the machine can take this
detergent during rinsing or softener step.
- Too much softener was put in.
- Detergent may have been stored
improperly.
- Type of material being washed (lace
items will cause excessive foam due to
their meshed structure).
The detergent dispenser is problematic. Water
is siphoned (pulling the softener into the washer
early) during the fill or rinse cycles.
- Detergent might have been put in the
wrong compartment.
Valves are problematic.
- Softener being released early.
There is foaming over the detergent drawer
Mix 1 tablespoonful softener and ½ liter water
and pour into the main wash compartment of the
detergent drawer.
Too much detergent was used
32 - EN
Download from Www.Somanuals.com. All Manuals Search And Download.
The plug might not be
plugged in the mains
outlet.
Check the plug.
Fuse may have blown.
Electricity may be cut
off.
Check the fuse.
Machine does work.
Nothing is displayed on
the screen.
Check the supply power.
The “On/Off” button
might have not been
pressed.
Press this button.
The machine did not
start after the program
was selected and the
“Start/Pause/Cancel”
button was pressed.
The front door may be
ajar.
The Rinse Symbol
amongst the Program
Indicator Symbols is
flashing. (Subject to the
model of your machine,
water cut-off symbol
may light up too)
You can restart your machine by
pressing the “Start/Pause/Cancel”
button for a short time after ensuring
that the water is not cut off.
Water may have been
cut off.
33 - EN
Download from Www.Somanuals.com. All Manuals Search And Download.
|