User Manual
ULTRAGAIN PRO-8 DIGITAL ADA8000
Audiophile 8-Channel A/D & D/A Converter with Premium Mic
Preamplifiers and ADAT Interface
Download from Www.Somanuals.com. All Manuals Search And Download.
3
ULTRAGAIN PRO-8 DIGITAL ADA8000 User Manual
9. Do not defeat the safety purpose of the polarized
TO BIND MUSIC GROUP BY ANY EXPRESS OR IMPLIED
UNDERTAKING OR REPRESENTATION. THIS MANUAL
IS COPYRIGHTED. NO PART OF THIS MANUAL MAY
BE REPRODUCED OR TRANSMITTED IN ANY FORM
Important Safety
Instructions
or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding-type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the OR BY ANY MEANS, ELECTRONIC OR MECHANICAL,
provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
INCLUDING PHOTOCOPYING AND RECORDING OF ANY
KIND, FOR ANY PURPOSE, WITHOUT THE EXPRESS
WRITTEN PERMISSION OF MUSIC GROUP IP LTD.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
Terminals marked with this symbol carry
electrical current of sufficient magnitude
to constitute risk of electric shock.
ALL RIGHTS RESERVED.
© 2013 MUSIC Group IP Ltd.
Trident Chambers, Wickhams Cay, P.O. Box 146,
Road Town, Tortola, British Virgin Islands
11. Use only attachments/accessories specified by
the manufacturer.
Use only high-quality professional speaker cables with
¼" TS or twist-locking plugs pre-installed. All other
installation or modification should be performed only
by qualified personnel.
12. Use only with the
cart, stand, tripod, bracket,
or table specified by the
LIMITED WARRANTY
For the applicable warranty terms and conditions
and additional information regarding MUSIC Group’s
Limited Warranty, please see complete details online at
manufacturer, or sold with
the apparatus. When a cart
is used, use caution when
moving the cart/apparatus
combination to avoid
This symbol, wherever it appears,
alerts you to the presence of uninsulated
dangerous voltage inside the
enclosure - voltage that may be sufficient to constitute a
risk of shock.
injury from tip-over.
This symbol, wherever it appears,
alerts you to important operating and
maintenance instructions in the
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has
been dropped.
accompanying literature. Please read the manual.
Caution
To reduce the risk of electric shock, do not
remove the top cover (or the rear section).
No user serviceable parts inside. Refer servicing to
qualified personnel.
Caution
To reduce the risk of fire or electric shock,
do not expose this appliance to rain and
15. The apparatus shall be connected to a MAINS socket
outlet with a protective earthing connection.
16. Where the MAINS plug or an appliance coupler is
used as the disconnect device, the disconnect device shall
remain readily operable.
moisture. The apparatus shall not be exposed to dripping
or splashing liquids and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
Caution
These service instructions are for use
by qualified service personnel only.
To reduce the risk of electric shock do not perform any
servicing other than that contained in the operation
instructions. Repairs have to be performed by qualified
service personnel.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
LEGAL DISCLAIMER
TECHNICAL SPECIFICATIONS AND APPEARANCES
ARE SUBJECT TO CHANGE WITHOUT NOTICE AND
ACCURACY IS NOT GUARANTEED. BEHRINGER,
KLARK TEKNIK, MIDAS, BUGERA, AND TURBOSOUND
ARE PART OF THE MUSIC GROUP (MUSIC-GROUP.COM).
ALL TRADEMARKS ARE THE PROPERTY OF THEIR
RESPECTIVE OWNERS. MUSIC GROUP ACCEPTS NO
LIABILITY FOR ANY LOSS WHICH MAY BE SUFFERED
BY ANY PERSON WHO RELIES EITHER WHOLLY OR
IN PART UPON ANY DESCRIPTION, PHOTOGRAPH
OR STATEMENT CONTAINED HEREIN. COLORS AND
SPECIFICATIONS MAY VARY FROM ACTUAL PRODUCT.
MUSIC GROUP PRODUCTS ARE SOLD THROUGH
AUTHORIZED FULLFILLERS AND RESELLERS ONLY.
FULLFILLERS AND RESELLERS ARE NOT AGENTS OF
MUSIC GROUP AND HAVE ABSOLUTELY NO AUTHORITY
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
ULTRAGAIN PRO-8 DIGITAL ADA8000 User Manual
1. Introduction
◊
Faulty fuses must be replaced with fuses of appropriate rating without
exception! The correct value of the fuses needed can be found in the
chapter “Specifications”.
Your ADA8000 is a state-of-the art 8-channel A/D and D/A converter. This ultra-
compact 19" unit gives you the opportunity to connect analog audio signals
directly to, say a multitrack recorder via the integrated ADAT interface. For this
purpose, the ADA8000 deserves one rack space only. In return, you can even
connect the digital signal of a multitracker via ADAT to the eight analog line
outputs of your ADA8000. Signal conversion can be processed at 44.1 or
48 kHz with 24-bit resolution. The ADAT inputs and outputs can be operated
independently as long as there is an identical wordclock signal. The integrated
A/D and D/A converters ensure optimal signal conversion without any distortion
or signal deterioration.
Power is delivered via the cable enclosed with the unit. All requiered safety
precautions have been adhered to.
◊
Please make sure that the unit is grounded at all times. For your own
protection, you should never tamper with the grounding of the cable or
the unit itself.
1.1.3 Warranty
Please take a few minutes and send us the completely filled out warranty
card within 14 days of the date of purchase. You may also register online at
behringer.com. The serial number needed for the registration is located at the top
of the unit. Failure to register your product may void future warranty claims.
IMP “Invisible” Mic Preamp
The microphone channels are fitted with BEHRINGER’s brand new high-end
IMP INVISIBLE MIC PREAMPs that boast the following features:
130 dB dynamic range for an incredible amount of headroom,
2. Control Elements
•
a bandwidth ranging from below 10 Hz to over 200 kHz for crystal-clear
reproduction of even the finest nuances
(1)
(2) (3)
(6)
(7)
•
the extremely low-noise and distortionless circuitry guarantees absolutely
natural and transparent signal reproduction
•
they are perfectly matched to every conceivable microphone with up to
60 dB gain and +48 volt phantom power supply and
•
they enable full utilisation of the greatly extended dynamic range of your
24-bit/192 kHz HD recorder, thereby maintaining optimal audio quality
◊
The following user’s manual is intended to familiarize you with the
unit’s control elements, so that you can master all the functions.
After having thoroughly read the user’s manual, store it at a safe place
for future reference.
(5)
(4)
(8)
(9)
Fig. 2.1: ADA8000 channel section
1.1 Before you get started
The ADA8000 features eight identical channels. Each section comprises
a microphone input (on a balanced XLR connector) and a line-level input
(on a balanced ¼" TRS jack). We recommend connecting only one input signal
per channel. When two input signals are connected, the weaker signal is
suppressed and will be audible as interference noise.
1.1.1 Shipment
The ADA8000 was carefully packed at the assembly plant to assure secure
transport. Should the condition of the cardboard box suggest that damage may
have taken place, please inspect the unit immediately and look for physical
indications of damage.
(1) The SIG LED lights up when a signal is present at one of the inputs.
◊
Damaged units should NEVER be sent directly to us. Please inform the
dealer from whom you acquired the unit immediately as well as the
transportation company from which you took delivery of the unit.
Otherwise, all claims for replacement/repair may be rendered invalid.
(2) If the input level is too high, the CLIP LED lights up. The CLIP LED should
light up only with signal peaks but never all the time.
(3) Use the GAIN control to set the input gain. The gain ranges from +10 to
+60 dB. The GAIN control governs both the LINE IN and the MIC IN input.
1.1.2 Initial operation
(4) This is the balanced ¼" TRS LINE IN connector. A connected analog
LINE IN or MIC IN signal is not routed to the analog LINE OUT connector (16).
Instead, it will reach the ADAT OUT interface.
Please make sure the unit is provided with sufficient ventilation, and never place
the ADA8000 on top of an amplifier or in the vicinity of a heater to avoid the risk
of overheating.
(5) This is the balanced MIC IN XLR connector. For example, you can connect
your microphone here.
◊
Before plugging the unit into a power socket, please make sure you
have selected the correct voltage:
(6) As long as the ADA8000 functions as master, sending a clock signal,
the SYNC MASTER LED lights up. The appropriate setting can be made on
the rear (see (15)).
The fuse compartment near the power plug socket contains three triangular
markings. Two of these triangles are opposite one another. The voltage indicated
adjacent to these markings is the voltage to which your unit has been set up,
and can be altered by rotating the fuse compartment by 180°.
(7) When the ADA8000 is synchronized externally (either ADAT or wordclock IN),
the SYNC LOCKED-LED lights up.
ATTENTION: This does not apply to export models that were for example (8) Press the +48 V switch to provide condenser microphones which are
manufactured only for use with 120 V!
connected to the MIC IN inputs with the required phantom power.
Dynamic microphones do not require this external power supply. When the
switch is depressed, phantom power is active on all inputs.
◊
If you alter the unit’s voltage, you must change the fuses accordingly.
The correct value of the fuses needed can be found in the
chapter “Specifications”.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
◊
ULTRAGAIN PRO-8 DIGITAL ADA8000 User Manual
Please mute your amplifier(s) before activating the phantom
power. Otherwise, switch-on thumps may be audible on your
loudspeakers/headphones.
(15) The setting of this switch depends on the application of your ADA8000. If an
external ADAT recorder is supposed to send the wordclock signal (in this case,
the ADA8000 functions as SLAVE), the switch has to be set to the ADAT IN
position. Please also note the instructions given in the user’s manual of your
ADAT device. When your ADA8000 functions as Master (here, the ADA8000
sends the wordclock signal) please use the switch to select the sampling rate
of your choice (either 44,1 or 48 kHz).
(9) The POWER switch powers the ADA8000 on. You should always make sure
that the POWER switch is in the “Off” position when initially connecting the
unit to the mains.
◊
Please take note: Merely switching the unit off does not mean that
it is fully disconnected from the mains. When not using the unit for
prolonged periods of time, please unplug the unit’s power cord from
the power outlet.
(16) Your ADA8000 features eight LINE OUTs on balanced XLR connectors.
An input signal present at the ADAT IN will automatically be transferred
into eight independent signals and routed to the eight analog
LINE OUT connectors.
(10)
(16)
(11)
Fig. 2.4: LINE OUT connectors
Fig. 2.2: Mains supply and fuse compartment
(10) FUSE COMPARTMENT / VOLTAGE SELECTION. Before connecting the unit
to a power outlet, please make sure that the selected voltage matches your
local voltage. When replacing fuses, please make sure that you always use
fuses of the same type. Some units allow for switching between 230 V
und 120 V. Please note: when connecting a unit intended for the European
3. Applications
Your ADA8000 is an ideal expansion for BEHRINGER’s digital mixing console
DDX3216, which features an optional ADAT interface. Thanks to the ADA8000,
this digital mixer can be expanded by eight additional analog inputs and
market to a 120 V power outlet, you must also replace the factory fuse with a outputs. Sound cards featuring ADAT INs and OUTs receive eight first-class analog
higher-value fuse.
inputs and outputs with the ADA8000. What’s more, the eight “Invisible” Mic
Preamps perfectly enable direct recording to digital multitrackers (e.g. ADAT).
Last but not least, you can also use the ADA8000’s audio channels to create a live
surround mix.
(11) Power is supplied via an IEC connector. The matching cable is provided with
the unit.
4. Audio Connections
You will need many different cables for the various applications. The following
illustrations show how these cables should be laid out.
Please use exclusively high-grade cables. The audio connectors of your ADA8000
are electronically balanced and ensure automatic hum and noise reduction.
Needless to say, even devices with unbalanced outputs can be connected to
the balanced in/outputs of your ADA8000. For this purpose, please use either
mono plugs or connect the ring of stereo plugs with the sleeve (when using XLR
connectors, pin 1 and pin 3 have to be bridged).
(12)
(13)
(14)
(15)
Fig. 2.3: ADAT IN/OUT and wordclock SYNC
◊
Please ensure that only qualified personnel install and operate the
ADA8000. During installation and operation the user must have
sufficient electrical contact to earth. Electrostatic charges might affect
the operation of the unit.
(12) All analog input signals are converted into the standard ADAT format and can
be taken at the 8-CHANNEL DIGITAL OUT. This output can be used to feed
an ADAT recorder or any other device featuring an ADAT input. Please note
that a signal present at the Digital In will not be routed to the Digital Out.
(13) At the 8-CHANNEL DIGITAL IN, you can connect an ADAT device. The signal
will automatically be routed to the 8 analog LINE OUT connectors.
(14) Use the WC IN connector to connect devices for the external synchronization
of your ADA8000. This BNC connector is only active, when the respective
setting on the rear is made (see (15)). When, for example, various devices
are interconnected in a digital recording system with, say, a digital mixing
console, all digital units connected have to be synchronized via a shared
wordclock signal.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
ULTRAGAIN PRO-8 DIGITAL ADA8000 User Manual
Fig. 4.4: Connecting the ADA8000 optically via Toslink
Wordclock output
device A
Wordclock input
ADA8000
signal ꢀow
Fig. 4.1: XLR connectors
terminating
resistor
Fig. 4.5: Unbalanced connection (termination) of the ADA8000’s wordclock input
Fig. 4.2: ¼" TS connector
Fig. 4.3: ¼" TRS connector
Download from Www.Somanuals.com. All Manuals Search And Download.
7
ULTRAGAIN PRO-8 DIGITAL ADA8000 User Manual
5. Specifications
Microphone Inputs
Synchronization
Type
Electronically balanced,
discrete input circuitry
Source
Internal 44.1 kHz, internal 48 kHz,
ADAT input, wordclock input
Gain range
+10 to +60 dB
Wordclock Input
Max. input level
Impedance
+6 dBu @ +10 dB gain for 0 dBFS
approx. 2 kΩ balanced
+48 V, switchable
Type
BNC, 1 x sample rate
2 to 6 V peak-to-peak
44.1 to 48 kHz
Input level
Frequency range
Phantom power
Line Inputs
System Specifications
Type
¼" TRS connector, electronically
balanced, discrete input circuitry
Frequency range
THD
10 Hz to 21 kHz @ 48 kHz sample rate
Impedance
approx. 20 kΩ balanced /
10 kΩ unbalanced
<0,01%
<-86 dB
Crosstalk
Gain range
-10 to +40 dB
Power Supply
Max. input level
+26 dBu @ -10 dB gain for 0 dBFS
Mains Voltage
USA / Canada
Line Outputs
120 V~, 60 Hz
230 V~, 50 Hz
100 V~, 50 - 60 Hz
120/230 V~, 50 - 60 Hz
25 W
Type
XLR, electronically balanced
Europe / U.K. / Australia
Japan
Impedance
approx. 500 Ω balanced /
250 Ω unbalanced
General export model
Power consumption
Fuse
Max. output level
+16 dBu @ 0 DBFS
Digital Input
100 - 120 V ~: T 630 mA H
200 - 240 V ~: T 315 mA H
Type
TOSLINK, optical connector
Mains connection
Standard IEC receptacle
Format
ADAT, 8 channels, 24-bit @ 44,1/48 kHz
Dimensions
Digital Output
(H x W x D)
8.46 x 1.75 x 19" / 215 x 44.5 x 482.6 mm
approx. 2.59 kg
Type
TOSLINK, optical connector
WEIGHT
Format
ADAT, 8 channels, 24-bit @ 44,1/48 kHz
SHIPPING WEIGHT
approx. 3.09 kg
A/D Converter
BEHRINGER constantly strives to maintain the highest quality standards. Modifications may be made,
if necessary, without prior notice. The specifications and appearance of the equipment may therefore differ from
those listed or illustrated.
Type
24-bit, 64-times oversampling,
delta-sigma
Dynamic range
Analog input to digital output,
approx. 103 dB
D/A Converter
Type
24-bit, 128-times oversampling,
delta-sigma
Dynamic range
Digital input to analog output,
approx. 100 dB
Download from Www.Somanuals.com. All Manuals Search And Download.
8
ULTRAGAIN PRO-8 DIGITAL ADA8000 User Manual
FEDERAL COMMUNICATIONS
COMMISSION COMPLIANCE
INFORMATION
ULTRAGAIN PRO-8 DIGITAL ADA8000
Responsible Party Name:
Address:
MUSIC Group Services US Inc.
18912 North Creek Parkway,
Suite 200 Bothell, WA 98011,
USA
Phone/Fax No.:
Phone: +1 425 672 0816
Fax: +1 425 673 7647
ULTRAGAIN PRO-8 DIGITAL ADA8000
complies with the FCC rules as mentioned in the following paragraph:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Important information:
Changes or modifications to the equipment not expressly approved by MUSIC Group
can void the user’s authority to use the equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
We Hear You
Download from Www.Somanuals.com. All Manuals Search And Download.
|