Baracoda Barcode Reader L User Manual

Data Capture  
for Workforce  
in Motion  
RoadRunners Evolution –L (1D) & -LA (Laser)  
Programming Guide  
©Baracoda TM – July 2009  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
2.8.6. SET LENGTHS FOR CODE 39.......................................................30  
2.8.7. ITALIAN PHARMACODE SETTINGS....................................................31  
2.9. CODE 93 SETTINGS .....................................................31  
2.9.1. ENABLE/DISABLE CODE 93.......................................................31  
2.9.2. SET LENGTHS FOR CODE 93 ......................................................31  
2.10. CODE 128 SETTINGS ...................................................32  
2.10.1. ENABLE/DISABLE CODE 128/EAN 128 .............................................32  
2.10.2. SET LENGTHS FOR CODE 128/EAN 128.............................................32  
2.10.3. EAN 128: GROUP SEPARATOR....................................................33  
2.10.4. ENABLE/DISABLE AIM ID TRANSMISSION............................................34  
2.11. INTERLEAVED  
2
OF 5 SETTINGS ...........................................34  
OF 5 .............................................34  
2.11.2. INTERLEAVED 2OF 5 CHECK DIGIT.................................................34  
2.11.3. SET LENGTHS FOR INTERLEAVED OF 5.............................................35  
2.11.1. ENABLE/DISABLE INTERLEAVED  
2
2
2.12. MSI CODE SETTINGS ...................................................35  
2.12.1. ENABLE/DISABLE MSI.........................................................35  
2.12.2. MSI CHECK DIGIT............................................................35  
2.12.3. SET LENGTHS FOR MSI.........................................................36  
2.13. STANDARD  
2
OF 5 SETTINGS..............................................36  
OF 5................................................36  
OF 5 CHECK DIGIT ..................................................36  
OF 5 ...............................................37  
2.13.1. ENABLE/DISABLE STANDARD  
2.13.2. STANDARD  
2.13.3. SET LENGTHS FOR STANDARD  
2
2
2
2.14. UPC/ EAN SETTINGS...................................................37  
2.14.1. ENABLE/DISABLE UPC/EAN.....................................................37  
2.14.2. TRANSMIT EAN13 CHECK DIGIT ..................................................38  
2.14.3. TRANSMIT UPC-E CHECK DIGIT ..................................................38  
2.14.4. TRANSMIT EAN 8 CHECK DIGIT...................................................38  
2.14.5. TRANSMIT UPC-A CHECK DIGIT ..................................................38  
2.14.6. TRANSMIT UPC NUMBER SYSTEM FOR UPC-E ..........................................39  
2.14.7. UPC-A, UPC-E, EAN CONVERSIONS ..............................................39  
2.14.8. ISSN/ISBN SETTINGS ........................................................40  
2.14.9. ADD-ON DIGITS SETTINGS.......................................................40  
2.15. GS1 DATABAR (RSS) 14 SETTINGS ........................................41  
2.15.1. ENABLE/DISABLE GS1 DATABAR 14................................................41  
2.15.2. GS1 DATABAR 14 CHECK DIGIT TRANSMISSION........................................41  
2.15.3. GS1 DATABAR 14 LINKAGE FLAG TRANSMISSION .......................................41  
2.15.4. GS1 DATABAR 14 APPLICATION ID TRANSMISSION .....................................41  
2.16. GS1 DATABAR (RSS) LIMITED SETTINGS ....................................42  
2.16.1. ENABLE/DISABLE GS1 DATABAR LIMITED............................................42  
2.16.2. GS1 DATABAR LIMITED CHECK DIGIT TRANSMISSION ....................................42  
2.16.3. GS1 DATABAR LIMITED LINKAGE FLAG TRANSMISSION....................................42  
2.16.4. GS1 DATABAR LIMITED APPLICATION ID TRANSMISSION..................................42  
3. APPENDIX 1: ASCII TABLE (A-Z, A-Z, 0-9, PUNCTUATION, CONTROL  
CHARACTERS)..............................................................43  
4. APPENDIX 2 – AIM SYMBOLOGY IDENTIFIERS STRUCTURE.....................48  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 3 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
Revision History  
Changes to the original manual are listed below.  
Document  
Date  
Description  
1.0  
11 July 08  
Initial release  
1.1  
1.2  
1.3  
26 Aug. 08  
11 Sept. 08  
02 July 09  
Update “Batch” section & add “The different connection method” section  
Add “Smart Autoscan” option.  
Modify “Operating Mode” section & Add “buffered data” section.  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 4 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
Introduction  
The RoadRunners Evolution scanner can be programmed by scanning barcode labels which contain commands  
for the decoder.  
Programming labels must be Code128, with specific starting and ending characters. These labels will always be  
read, even if Code128 symbology is disabled.  
The scanner will acknowledge a good and valid programming barcode label reading with two beeps and a green  
enlightening of the led. It will give two other beeps (lower tone) and a red enlightening of the led for either an  
invalid or bad reading.  
Please do not read the programming barcodes while being connected to the BaracodaManager software.  
Programmable options are divided into 2 groups. The first group includes the options that show the general  
behaviour of the scanner. The second group sets the decoding parameters for each barcode symbology.  
This document concerns the Roadrunners 1D Evolution scanners, that is the BRR-L Evolution and the BRR-LA  
Evolution.  
All our documentations can be downloaded from the Partners download section of Baracoda website  
(registration is required):  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 5 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
1. General Configuration  
1.1. General default settings  
The reading of the "Reset to factory settings” label turns all the parameters of the scanner back to default  
settings and switches it off  
Reset to factory settings  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 6 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
1.2. Baracoda advanced features  
1.2.1. Switch on delay  
In order to switch on the scanner in its standard mode, you should just press the trigger. You can set up the  
scanner to be switched on only after keeping the trigger pressed for two (2) seconds by reading the  
appropriate barcode.  
Switch on delay : 2 seconds  
Switch on delay : 0 second (*)  
1.2.2. Shutdown timers  
There are two different ‘shutdown timers’:  
- When connected timer: delay between the last scanned barcode and the switch off when the  
scanner is connected to a host  
- Not connected timer: delay between the last scanned barcode and the switch off when the scanner is  
not connected to any host  
It is possible to set those timers to ‘infinite’. In this case, the scanner will stay all the time ON.  
Set shutdown timers to infinity  
By default, timers value are:  
-
-
When connected timer = 20 minutes  
Not connected timer = 10 minutes  
Set shutdown timers to defaults  
1.2.3. Turn scanner OFF  
To turn off the scanner, read the following barcode:  
Turn off scanner  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 7 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
1.2.4. No data loss mode and Baracoda Header  
Baracoda header:  
It is a proprietary data encapsulation. It is necessary to activate it to use the Baracoda keyboard emulation  
(Kemul) and Terminal.  
The Baracoda header is enabled in default settings  
No data loss mode:  
Baracoda has developed a proprietary communication protocol in order to enhance the security of the  
Bluetooth transmission.  
Every barcode sent to the host must be acknowledged by the host (until then, the scanner will transmit it again  
and again).  
This acknowledgment is disabled in default settings. It is strongly recommended to set this protocol  
acknowledgment on when using the scanner with the BaracodaManager.  
Enable Baracoda header + “No Data loss mode” ON  
Enable Baracoda header + “No Data loss mode” OFF (*)  
Disable Baracoda header + “No data loss mode” OFF  
1.3. Reading Mode  
In Trigger mode, pressing the trigger will activate the beam.  
Trigger (*)  
The Aiming trigger mode has been developed for users who need to scan barcodes very close one to another  
and they have to be sure to always read the correct one. Once in this mode, in order to read a barcode user will  
have to press the trigger twice. Pressing it the first time will switch on the beam but will not switch on the  
decoder (thus allowing user to aim at the correct barcode) while pressing the trigger the second time will  
activate the decoder thus allowing the scanner to actually decode the barcode.  
Aiming Trigger Mode  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 8 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
In Autoscan mode, the scan beam is continuously on. This mode enables to scan continuously.  
Autoscan  
In Smart Autoscan mode, for a battery power consumption optimisation issue, the scanner will be  
continuously flashing.  
Smart Autoscan  
The “No duplicate scan” option has been developed for users who do not want to scan the same barcode  
twice.  
« no duplicate scans » disabled (*)  
« no duplicate scans » enabled + error signal  
If the same barcode is scanned, an error signal is played (two beeps (lower tone) and a red  
enlightening of the led)  
« no duplicate scans » enabled + no decoding  
If the same barcode is trying to be scanned, it won’t be. The laser beam will still be enlightening.  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 9 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
1.4. Operating Mode  
Real Time mode  
In real time mode, the barcode is decoded and transmitted to the remote host without any delay. If the  
scanner is not connected, the data is lost.  
Real Time mode with No Data Loss option  
If the No Data Loss option is activated and if the scanner is not connected or out of Bluetooth range, the  
scanner will store the data. It can memorise up to 10 000 barcodes (UPC format) and later automatically upload  
them to the remote host when a Bluetooth connection is established to the host.  
Every barcode sent to the host must be acknowledged by the host. If the host fails to send an  
acknowledgement, the scanner will continue to transmit the barcode until the host does send an  
acknowledgement.  
This acknowledgment is disabled in the default settings. It is strongly recommended to set the No Data Loss  
mode to ON. This configuration can be set with the BaracodaManager software or with the Programming  
Guide.  
Additionally, this protocol acknowledgment allows an end user to set an audio acknowledgment indicating that  
the barcode has been successfully transmitted to the host.  
Batch mode  
Barcodes are always stored in the scanner. Once the batch mode is selected, the BCL led (right) emits an  
orange flash. In batch mode, the barcode can read up to 10 000 barcodes (UPC format) and store them into its  
non-volatile memory for later transmission to the host. When the internal memory is full, both Leds will be full  
orange (no blinking).  
To upload barcodes from the scanner, connect it to the host computer via Bluetooth. The BaracodaManager  
software is used to configure the location where the barcodes are sent once the barcodes are extracted from  
the scanner.  
Once connected, the scanner will wait for the appropriate command in order to start uploading the barcodes:  
this command can come from:  
The BaracodaManager: The user has to click on the button “Upload”.  
A configuration scan barcode: the user has to read the appropriate configuration barcode.  
Be aware that with BaracodaManager, two (2) different ways to upload barcodes are possible:  
To an application window: In this case always double check before starting the upload  
procedure that the cursor in your text window is active. Otherwise you will loose all the data  
saved into your scanner.  
To a .txt file (default option). The BaracodaManager gives you the possibility to modify the  
name of the file in which you may want to save the data.  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 10 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
1.4.1. Real Time mode  
Erases all captured data stored in memory and forces the scanner in Real time mode. No other setting is  
changed.  
Important reminder: if an ACK beep or buffer is needed, the scanner must be set in the “no data loss mode”  
first.  
Enable Real Time with « No Data Loss »  
mode  
Enable Real Time without « No Data  
Loss » mode  
1.4.2. No Data Loss mode - Enable “ACK” beep  
Forces the scanner in Real Time mode (with data acknowledgement); Erases all captured data stored in  
memory. The scanner should have been previously set in the “No data loss mode” ON (So scan the “Enable Real  
Time with No Data Loss mode” barcode before).  
Enable ACK beep  
1.4.3. No Data Loss mode - Disable “ACK” beep  
Forces the scanner in Real Time mode (without data acknowledgement); Erases all captured data stored in  
memory. The scanner should have been previously set in the “No data loss mode” ON (So scan the “Enable Real  
Time with No Data Loss mode” barcode before).  
Disable ACK beep  
1.4.4. Real Time - Buffered data option  
It’s possible to set the scanner in “Real Time with No Data Loss mode” but with no bufferisation (buffer  
configured to 0) when it’s not connected. In this particular situation the trigger will not activate the beam: so  
impossible to read barcodes in this mode, and Both LEDs blinks orange.  
Max Buffered Barcodes  
=
0
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 11 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
Max Buffered Barcodes  
=
MAX  
1.4.5. Batch mode  
BATCH MODE  
Forces the RoadRunners Evolution in Batch mode. Erases all codes in memory  
When in batch mode, the scanner will wait for the appropriate command in order to start uploading the  
barcodes: this command can come  
from the BaracodaManager  
from reading the “Upload batch data” barcode here after  
If this barcode is read when the reader is in batch mode and connected, the reader will automatically upload to  
the host all the data in its memory. If not in batch mode or not connected, the scanner will ignore this barcode.  
Upload batch data (with No Data Loss on)  
When scanning this barcode, the scanner will send a message to the host, meaning that it wants to upload its  
data. Following this, the host will launch the upload process and grab the batch data.  
If the host application has received all the expected data, it will acknowledge the upload to the scanner which  
will erase the data from its memory. If not, the host application will send a negative acknowledgment message  
to the scanner which will keep the data in memory, ready to retry an upload.  
If the data transfer has been successful (the scanner has received the acknowledgment and erased its memory)  
and, for any reason, the user gets to realize that data has been lost at a higher level (keyboard emulation for  
example), it still has the possibility to recover the last batch data into the scanner’s memory, by scanning the  
below barcode.  
Restore last batch data  
Restore last batch + launch upload  
Please note that the data recovering won’t be possible if other barcodes have been scanned or if the scanner  
has been shut down after the upload.  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 12 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
1.5. The different connection methods  
There are two (2) different way to create a connection from a Host and a scanner:  
-
Slave mode (by default)  
The Host (PC, BaracodaManager, …) is creating the connection onto the scanner.  
-
Master mode  
The scanner is creating itself a connection to the recorded Host Bluetooth address. This connection  
attempt is set after a scan of barcode. The configuration of Host address (on which the scanner will set  
up a connection) can be done:  
o
o
Via BaracodaManager software.  
Via scan of barcodes.  
All usage mode (Real Time, No Data Loss, Batch) are obviously available on those two different ways of  
connection.  
Enable master mode  
Disable master mode  
\ V T \ V T Z \ N U L \ S O H \ S O H \ F F \ F F  
Enable master mode and disconnect  
\ V T \ V T Z \ N U L \ S O H \ N U L \ F F \ F F  
Disable master mode and disconnect  
\VT\VTZ\NUL\STX\SOH\SOH\FF\FF  
\VT\VTZ\NUL\STX\NUL\SOH\FF\FF  
The configuration of the Host Bluetooth address (BDA) is made by scanning the 0-9, a-f, A-F labels (Appendix 1)  
as on a calculator; following the timestamp format shown above.  
For example: to set the following BDA: 00:c3:EF:44:a2:B9, the user will scan:  
- “Set Remote BDA” label,  
- “0” label,  
- “0” label,  
- “c” label,  
- “3” label,  
- “E” label,  
- “F” label,  
- “4” label,  
- “4” label,  
- “a” label,  
- “2” label,  
- “B” label,  
- “9” label,  
- “End of Config” label.  
Set Remote BDA  
End of Config  
\
L
F
\
L
F
E
N
D
\
F
F
\
F
F
\ V T \ V T ^ \ N U L \ S O H \ E N Q \ L F \ L F  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 13 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
1.6. Buzzer and Led Settings  
You can use these options to enable or disable the buzzer and / or the Led.  
LED ON (*)  
LED OFF  
Good read beep on (*)  
Good read beep off  
ACK beep on (*)  
ACK beep off  
Beep level volume = HIGH (*)  
Beep level Volume = LOW  
BUZZER ON (*)  
BUZZER OFF  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 14 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
1.7. Bluetooth settings  
1.7.1. Bluetooth name  
You can change the scanner Bluetooth name; name that you see during a search of Bluetooth peripheral.  
Programming procedure for “Set Bluetooth Name”  
Set BT Name  
End of config  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 15 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
1.7.2. Sniff period settings  
Change the Sniff period. If the higher is the latency and the smaller is the power consumption.  
Default value is 150ms.  
Sniff period = 150ms (*)  
Sniff period = 100ms  
Sniff period = 200ms  
Sniff period = 300ms  
Sniff period = 500ms  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 16 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
1.7.3. Security (code PIN) settings  
Some Bluetooth device will not accept connections with devices that do not have a security code.  
Disable BT security code  
Enable BT security code (*)  
1.7.4. RF Power emission settings  
For regulation purposes, some countries may limit the RF power emission to 10dBm (Class2 device).  
Set device to Class1 power emission (20dBm)(*)  
Limit device to Class2 power emission (10dBm)  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 17 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
1.8. Data format  
The barcode string can be added a timestamp, prefixes and/or suffixes. The symbology prefix/suffix can be  
added by BaracodaManager only.  
These can come as described below:  
Timestamp  
12 chars  
Data prefix  
Data (which type can be barcode or RFID)  
-
Data suffix  
Max. 32 chars  
Max. 32 chars  
Barcode Data:  
If data type is barcode, it comes with this data frame format  
Barcode prefix  
Max. 32 chars  
Barcode  
-
Barcode suffix  
Max. 32 chars  
Barcode:  
Depending on the barcode type (symbology), additional data can be added  
Symbology prefix  
Max. 4 chars  
AIM identifier  
0, 2 or 3 chars  
Data (barcode)  
-
Symbology suffix  
Max. 4 chars  
1.8.1. Timestamp option  
Timestamp can be configured (ON/OFF, set new date and new time) by the following configuration barcodes.  
Timestamp on  
Timestamp off (*)  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 18 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
START  
Read « Set Timestamp » label  
Read intermediary label  
Corresponding to the next digit to set for the  
Timestamp (from Appendix 1)  
NO  
Finished ? (1)  
YES  
Read « END of config » label  
END  
Programming procedure for “set Timestamp” option  
Set Timestamp  
END of configuration  
Noted that the timestamp must fit the specific following format:  
{YY} {MM} {DD} {HH} {MM} {SS}  
The setting is made by scanning the 0-9 labels (Appendix 1) as on a calculator; following the timestamp format  
shown above.  
For example: to set the current time at 16th May 2007, 3.25 pm, the user will scan:  
- “Set Timestamp” label,  
- “0” label,  
- “7” label,  
- “0” label,  
- “5” label,  
- “1” label,  
- “6” label,  
- “1” label,  
- “5” label,  
- “2” label,  
- “5” label,  
- “0” label,  
- “0” label,  
- “end of config” label.  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 19 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
1.8.2. Data Prefix/Suffix  
You can add a data prefix and/or suffix (strings of more than 32 characters will not be accepted) to  
every barcode sent to the host device.  
There is no data prefix or suffix in default settings.  
Enable data prefix  
Disable data prefix (*)  
Enable data suffix  
Disable data suffix (*)  
If enabled, a data prefix/suffix can be set as following:  
Start  
Read « « set prefix (suffix) » barcode  
Read intermediary label corresponding to the  
next character to set for the prefix (suffix)  
(see appendix 1)  
NO  
Finished ?  
YES  
Read « end of config » barcode  
End  
Procedure to define Data/Barcode Prefix/Suffix  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 20 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
Set Data prefix  
Set Data suffix  
End of configuration  
1.8.3. Barcode Prefix/Suffix  
You can add a barcode prefix and/or suffix (strings of more than 32 characters will not be accepted) to every  
barcode sent to the host device.  
There is no barcode prefix or suffix in default settings.  
Enable barcode prefix  
Disable barcode prefix (*)  
Enable barcode suffix  
Disable barcode suffix (*)  
If enabled, a Barcode prefix/suffix can be set in the same manner as the Data prefix/suffix can be set:  
Set Barcode prefix  
Set Barcode suffix  
End of configuration  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 21 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
1.8.4. AIM Symbology Identifier  
AIM Identifier will be transmitted at the beginning of the barcode. More information about the AIM Identifier is  
available in Appendix2.  
AIM Symbology identifier - not transmitted (*)  
AIM Symbology identifier - transmitted  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 22 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
2. Decoder Parameters  
2.1. Decoder default settings  
Sets the defaults decoder settings for all the symbologies  
Set Decoder Default Settings  
2.2. Enable/Disable All Symbologies  
Even if all symbologies are disabled, the scanner will always be able to read the programming barcodes of this  
document.  
Disable all symbologies  
Enable all symbologies (*)  
2.3. Set decoder barcode length  
You can set a fixed length for the barcode decoding. The scanner will only decode barcodes of this length,  
regardless the barcode symbology decoded.  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 23 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
Set barcode length  
END of config  
2.4. Voting  
Standard voting set is two (2). This means that a barcode is considered read by the decoder if the same data is  
decoded twice. Changing this parameter will enable a stronger security on the decoding of the barcode.  
Voting = 2 (*)  
Voting = 3  
Voting = 4  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 24 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
2.5. Min/Max length per symbology  
The following is a procedure to follow for every barcode symbology. The decoder offers the possibility to limit  
the reading of a barcode to a minimum and a maximum length, if it is fo one given symbology type.  
Start – set min length  
Start – Set Max length  
End of config  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 25 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
2.5.1. Symbology table  
Header  
Selected Symbology  
SELECT ALL  
Code 93  
Code 128 / EAN 128  
Code 39  
Codabar  
Interleaved 2 of 5  
Standard 2 of 5 (industrial 2 of 5)  
Code 11  
MSI  
Only the variable length symbologies appear.  
2.6. Codabar settings  
2.6.1. Enable/Disable Codabar  
To enable or disable Codabar, scan the appropriate barcode below.  
Disable  
Enable (*)  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 26 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
2.6.2. Codabar Start/Stop characters  
Not transmitted (*)  
Transmitted  
2.6.3. Codabar Check Digit Verification (AIM recommendation)  
Not used (*)  
Checked and transmitted  
Checked but not transmitted  
2.6.4. Set Lengths for Codabar  
Any length  
Barcode length Min=6 (*)  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 27 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
2.7. Code 11 Settings  
2.7.1. Enable/Disable Code 11  
To enable or disable Code 11, scan the appropriate barcode below.  
Code 11 - not active (*)  
Code 11 - active  
2.7.2. Code 11 check digit(s) verification  
1 digit (*)  
2 digits  
2.7.3. Transmit Code 11 check digit(s)  
This feature selects whether or not to transmit the Code 11 check digit(s).  
Check and transmitted (Enable) (*)  
Check but not transmitted (Disable)  
2.7.4. Set Length for Code 11  
This features check the length of the barcode.  
Code 11 - barcode length - any  
length  
Code 11 – barcode length – Min = 6 (*)  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 28 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
2.8. Code 39 settings  
2.8.1. Enable/Disable Code 39  
To enable or disable Code 39, scan the appropriate barcode below.  
Enable (*)  
Disable  
2.8.2. Enable/Disable Code 39 Full ASCII  
Code 39 - format - standard 43 characters  
(*)  
Code 39 - format - full ASCII  
2.8.3. Code 39 Start/stop characters  
Code 39 - start/stop - not transmitted (*)  
Code 39 - start/stop - transmitted  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 29 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
2.8.4. Accepted Code 39 characters  
Code 39 - start/stop - accepted characters - * only (standard Code 39) (*)  
Code 39 - start/stop - accepted characters - $ only (Trioptic Code 39)  
Code 39 - start/stop - accepted characters - $ and * (standard and Trioptic Code 39)  
2.8.5. Code 39 Check Digit Verification  
Code 39 - check digit - not used (*)  
Code 39 - check digit - modulo 43 - checked and  
transmitted  
Code 39 - check digit - modulo 43 - checked but not  
transmitted  
2.8.6. Set lengths for Code 39  
Code 39 - barcode length - any length (*)  
Code 39 - barcode length - minimum length = 6  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 30 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
2.8.7. Italian PharmaCode settings  
Italian PharmaCode is based on Code39 encoding scheme, thus its settings are Code39 settings.  
Code 39 – Italian Pharmacode – not active (*)  
Code 39 – Italian Pharmacode – active  
Code 39 – Italian Pharmacode – Enable ‘A’ character transmission  
Code 39 – Italian Pharmacode – Disable ‘A’ character transmission (*)  
2.9. Code 93 Settings  
2.9.1. Enable/Disable Code 93  
To enable or disable Code 93, scan the appropriate barcode below.  
Code 93 - not active  
Code 93 – active (*)  
2.9.2. Set Lengths for Code 93  
Code 93 - barcode length - any  
length  
Code 93 - barcode length - minimum length = 6  
(*)  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 31 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
2.10. Code 128 Settings  
2.10.1. Enable/Disable Code 128/EAN 128  
To enable or disable Code 128/EAN 128, scan the appropriate barcode below.  
Disable  
Enable (*)  
2.10.2. Set lengths for Code 128/EAN 128  
Code 128/EAN 128 - barcode length - any length (*)  
Code 128/EAN 128 - barcode length - minimum length = 6  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 32 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
2.10.3. EAN 128: Group Separator  
‘FNC1’ included in an EAN128 code is transmitted by default as ‘GS’ (Group Separator – 0x1D).  
Enable GS transmission (*)  
Disable GS Transmission  
There is also the possibility to replace this character by any other of the user’s choice:  
Define GS replacement character  
End of configuration  
The most common request to replace ‘GS’ by the | (pipe) can be done through the scan of:  
Define | as GS  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 33 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
2.10.4. Enable/Disable AIM ID Transmission  
Even if the “AIM ID transmit” is disabled, it is possible to enable the AIM ID transmission for EAN128.  
Enable AIM ID transmission for EAN128  
Disable AIM ID transmission for EAN128 (*)  
2.11. Interleaved 2 of 5 Settings  
2.11.1. Enable/Disable Interleaved 2 of 5  
To enable or disable Interleaved 2 of 5, scan the appropriate barcode below  
Interleaved 2 of 5 - not active  
Interleaved 2 of 5 – active (*)  
2.11.2. Interleaved 2of 5 Check Digit  
Interleaved 2 of 5 - check digit - not used (*)  
Interleaved 2 of 5 - check digit - mod 10 - checked and  
transmitted  
Interleaved 2 of 5 - check digit - mod 10 - checked but not  
transmitted  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 34 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
2.11.3. Set lengths for Interleaved 2 of 5  
Interleaved 2 of 5 - barcode length - minimum length = 6 (*)  
Interleaved 2 of 5 – barcode length- any length  
2.12. MSI Code Settings  
2.12.1. Enable/Disable MSI  
To enable or disable MSI code, scan the appropriate barcode below.  
MSI Code - not active (*)  
MSI Code – active  
2.12.2. MSI Check Digit  
MSI Code - check digit - mod 10 - checked and transmitted (*)  
MSI Code - check digit - mod 10 - checked but not transmitted  
MSI Code - check digit - double mod 10 - checked and transmitted  
MSI Code - check digit - double mod 10 - checked but not transmitted  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 35 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
2.12.3. Set lengths for MSI  
MSI Code - barcode length - any  
length  
MSI Code - barcode length - minimum length = 6  
(*)  
2.13. Standard 2 of 5 Settings  
2.13.1. Enable/Disable Standard 2 of 5  
To enable or disable Standard 2 of 5 code, scan the appropriate barcode below.  
Standard 2 of 5 - not active  
Standard 2 of 5 – active *  
2.13.2. Standard 2 of 5 Check Digit  
Standard 2 of 5 - check digit mod 10 - not used (*)  
Standard 2 of 5 - check digit mod 10 - checked and transmitted  
Standard 2 of 5 - check digit mod 10 - checked but not transmitted  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 36 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
2.13.3. Set lengths for Standard 2 of 5  
Standard 2 of 5 - barcode length - any  
length  
Standard 2 of 5 - barcode length - minimum length = 6  
(*)  
2.14. UPC/ EAN Settings  
2.14.1. Enable/Disable UPC/EAN  
UPC / EAN - active (*)  
UPC / EAN - not active  
UPC / EAN - UPC-A and EAN 13 deactivated  
UPC / EAN - UPC-E deactivated  
UPC / EAN - EAN-8 deactivated  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 37 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
2.14.2. Transmit EAN13 Check Digit  
UPC / EAN - check digit - UPC-A and EAN13 - transmitted (*)  
UPC / EAN - check digit - UPC-A/EAN 13 - not transmitted  
2.14.3. Transmit UPC-E Check Digit  
UPC / EAN - check digit - UPC-E - transmitted (*)  
UPC / EAN - check digit - UPC-E - not transmitted  
2.14.4. Transmit EAN 8 Check Digit  
UPC / EAN - check digit - EAN-8 - transmitted (*)  
UPC / EAN - check digit - EAN-8 - not transmitted  
2.14.5. Transmit UPC-A Check Digit  
UPC / EAN - UPC number system - UPC-A - transmitted (*)  
UPC / EAN - UPC number system - UPC-A - not transmitted  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 38 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
2.14.6. Transmit UPC number system for UPC-E  
UPC / EAN - UPC number system - UPC-E - transmitted (*)  
UPC / EAN - UPC number system - UPC-E - not transmitted  
2.14.7. UPC-A, UPC-E, EAN conversions  
UPC / EAN - re-encoding UPC-A, UPC-E, EAN-8 - UPC-A transmitted as EAN-13  
UPC / EAN - re-encoding UPC-A, UPC-E, EAN-8 - UPC-A transmitted as UPC-A (*)  
UPC / EAN - re-encoding UPC-A, UPC-E, EAN-8 - UPC-E transmitted as UPC-E (*)  
UPC / EAN - re-encoding UPC-A, UPC-E, EAN-8 - UPC-E transmitted as UPC-A  
UPC / EAN - re-encoding UPC-A, UPC-E, EAN-8 - EAN-8 transmitted as EAN 8 (*)  
UPC / EAN - re-encoding UPC-A, UPC-E, EAN-8 - EAN-8 transmitted as EAN-13  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 39 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
2.14.8. ISSN/ISBN settings  
UPC / EAN – ISSN/ISBN – Active (*)  
UPC / EAN – ISSN/ISBN – Not active  
UPC / EAN – ISSN/ISBN – ISSN hyphen not transmitted (*)  
UPC / EAN – ISSN/ISBN – ISSN hyphen transmitted  
UPC / EAN – ISSN/ISBN – ISSN price code not transmitted (*)  
UPC / EAN – ISSN/ISBN – ISSN price code transmitted  
2.14.9. Add-on digits settings  
UPC / EAN – Add-on digits – 2-digit add-ons not active (*)  
UPC / EAN – Add-on digits – 2-digit add-ons active  
UPC / EAN – Add-on digits – 5-digit add-ons not active (*)  
UPC / EAN – Add-on digits – 5-digit add-ons not active  
UPC / EAN – Add-on digits – not required but transmitted if read (*)  
UPC / EAN – Add-on digits – required and transmitted  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 40 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
2.15. GS1 DataBar (RSS) 14 Settings  
2.15.1. Enable/Disable GS1 DataBar 14  
GS1 DataBar 14 - active (*)  
GS1 DataBar 14 – not active  
2.15.2. GS1 DataBar 14 Check Digit Transmission  
GS1 DataBar 14 - check digit - transmitted (*)  
GS1 DataBar 14 - check digit - not transmitted  
2.15.3. GS1 DataBar 14 Linkage flag Transmission  
GS1 DataBar 14 – Linkage Flag - not transmitted (*)  
GS1 DataBar 14 - Linkage Flag - transmitted  
2.15.4. GS1 DataBar 14 Application ID Transmission  
GS1 DataBar 14 – Application ID - transmitted (*)  
GS1 DataBar 14 - Application ID - not transmitted  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 41 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
2.16. GS1 DataBar (RSS) Limited Settings  
2.16.1. Enable/Disable GS1 DataBar Limited  
GS1 DataBar Limited - active (*)  
GS1 DataBar Limited – not active  
2.16.2. GS1 DataBar Limited Check Digit Transmission  
GS1 DataBar Limited - check digit - transmitted (*)  
GS1 DataBar Limited - check digit - not transmitted  
2.16.3. GS1 DataBar Limited Linkage flag Transmission  
GS1 DataBar Limited – Linkage Flag - not transmitted (*)  
GS1 DataBar Limited - Linkage Flag - transmitted  
2.16.4. GS1 DataBar Limited Application ID Transmission  
GS1 DataBar Limited – Application ID - transmitted (*)  
GS1 DataBar Limited - Application ID - not transmitted  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 42 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
3. APPENDIX 1: ASCII Table (A-Z, a-z, 0-  
9, punctuation, Control characters)  
Capital letters (A-Z):  
Name  
Programming label  
Name  
Programming label  
A
N
B
C
D
E
F
O
P
Q
R
S
G
H
I
T
U
V
W
X
J
K
L
Y
M
Z
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 43 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
Small letters (a-z):  
Name  
Programming label  
Name  
Programming label  
a
b
c
d
e
f
n
o
p
q
r
s
g
h
i
t
u
v
w
x
Y
z
j
k
l
m
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 44 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
Ponctuation:  
Name  
Programming label  
Name  
Programming label  
Space  
<
=
>
?
!
"
#
$
%
&
'
$
@
[
\
L
F
\
L
F
$
\
L
F
\
L
F
]
^
_
{
|
(
)
*
+
,
}
~
:
-
.
;
/
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 45 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
Decimal numbers (0-9):  
Name  
Programming label  
0
1
2
3
4
5
6
7
8
9
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 46 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
Control Characters:  
Name Programming label  
CR  
EOT  
ETX  
LF  
NUL  
SOH  
STX  
TAB  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 47 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Data Capture  
for Workforce  
in Motion  
4. APPENDIX 2 – AIM symbology identifiers  
structure  
The SI prefix is a two (2) or three (3) character string:  
] c m where  
] : SI indicator  
c : Symbology Identification  
m : Modifier characters (optional)  
Symbology Character  
A
B
C
D
E
Code 39  
Telepen  
Code 128  
Code One  
EAN/UPC  
F
Codabar  
G
H
I
Code 93  
Code 11  
ITF 25  
K
L
Code 16K  
PDF417  
M
N
O
P
R
S
MSI code  
Anker Code  
Codablock  
Plessey Code  
Straight 2 of 5 (two bar start/stop codes)  
Straight 2 of 5 (three bar start/stop codes)  
Code 49  
T
X
Z
Other Bar code  
Non Barcode data  
Modifier Characters  
The modifier character is determined by summing the option values of each symbology. If the sum is greater  
than 9, use A, B, C, D, E, F in the place of 10, 11, 12, 13, 14 and 15.  
Code 39 Option Values  
0
1
2
4
No check character or Full ASCII  
Reader has performed mod 43 check  
Reader has performed mod 43 check and stripped the check character  
Reader has performed Full ASCII conversion  
Telepen Option Values  
0
1
2
4
Full ASCII mode  
Double density numeric mode  
Double density numeric followed by full ASCII  
Full ASCII followed by double density numeric  
Code 128 Option Values  
0
1
2
4
Standard  
Function code 1 in first character position  
Function code 2 in second character position  
Concatenation according to ISBT specification has been performed, and concatenated data follows.  
RoadRunners Evolution –L (1D) & -LA (Laser) – Programming Guide v1.3  
- 48 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  

3M VCR MTA 2 User Manual
Abocom Network Card UFT128S User Manual
ACR Electronics Marine Lighting 1933 User Manual
Addonics Technologies Computer Drive AEPDDESU User Manual
American Dryer Corp Clothes Dryer AD 145 User Manual
American Standard Hot Tub 047438 0070A User Manual
American Standard Plumbing Product 2455 User Manual
ATON Speaker A60C User Manual
Axis Communications Security Camera M1145L User Manual
Axor Plumbing Product 14876001 User Manual