Baby Trend Baby Furniture 8207BCC User Manual

Read all instructions BEFORE assembly and USE of product.  
KEEP INSTRUCTIONS FOR FUTURE USE.  
Model #: 8207BCC  
DELUXE TREND NURSERY CENTER  
Instruction Manual  
Convenience through Innovation and thoughtful design  
05.07  
Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TO ASSEMBLE PLAYARD  
FOR THE SAFETY OF YOUR CHILD, PLEASE READ THE INSTRUCTIONS COMPLETELY  
BEFORE ASSEMBLING THE PLAYARD, BASSINET AND CHANGING AREA  
CONTENTS (Fig. 1-1):  
1 Playard  
1 Mattress  
1 Organizer  
2 Leg extensions (1 Left,1 Right)  
2 Leg extensions (1 Left, 1 Right) with Wheels,  
and hardware  
Figure 1-1.  
1 Travel or Storage bag  
BEFORE YOU BEGIN: The Baby Trend Playard is designed so that,  
when properly setup, the fabric of the playard places pressure on the 4  
top rails making them nearly impossible to unlock. This safety feature  
is activated when you push down on the playard floor to lock the bottom  
rails. When setting up the playard, if you allow the bottom rails to lock  
before locking the top rails, the fabric pressure will not allow you to lock  
the top rails. Please see (Fig. 7.) for the proper position of the bottom of the  
playard when locking the top rails. Always keep fingers away from corners  
when setting playard up.  
Figure 1.  
1. Unzip bag and remove Playard frame (Fig. 1). Undo the 3 Velcro straps  
and set mattress aside (Fig. 2).  
Figure 2.  
2. Turn the playard upside down. (Fig. 3). Push each leg extension into the  
bottom of the leg until both sides of extension snap into place. (Fig. 4).  
Check that the extension is firmly connected. Attach the wheels to the  
playard with the axle and nut as shown in figure (Fig. 5). The brake cluster  
on the wheel must face to the inside. The axle is inserted from the outside  
to the inside. (Fig. 6). Check that the wheels are firmly connected.  
3. Stand Playard on legs keeping feet of playard close together as shown in  
(Fig. 7). Pull up on top rails until all rails “click” and “lock”.  
Leg extensions  
* READ IMPORTANT: In order to continue, the handle in the center  
of the floor of the Playard MUST remain raised in order for the  
rail to lock (approx. 45.7 cm or 18 inches). The feet of the playard  
should almost touch each other. All 4 bottom rails must be pointed  
upward in order to LOCK top rails.  
4. Push down on center of Playard floor until it is flat and locks into  
position (Fig. 8). The center lock mechanism will lock automatically.  
The center lock will rotate clockwise about 90 degrees as it locks.  
Wheels  
NOTE: Test rails to make sure they are locked. Push down on each  
rail making sure they are rigid and in a set position.  
Figure 3  
3
Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING: All top rails MUST be  
straight and locked in position or child may  
become entrapped and suffocate.  
See figure 9 and 10.  
5. Place mattress in Playard with padded side up (Fig. 11).  
Figure 4  
Right  
Left  
NOTE: DO NOT insert mattress if using bassinet feature. Go to  
bassinet instructions.  
6. Feed the 3 hook and loop straps (found underneath the mattress),  
through the slots on the bottom of the sides of the Playard. Fasten  
the hook and loop straps to the underside of Playard to prevent the  
mattress from moving (Fig. 12) (Fig. 13).  
Insert  
axle from  
outside  
Insert  
axle from  
outside  
WARNING: To prevent child from  
becoming entrapped under the mattress pad  
and suffocating, hook and loop straps MUST  
Left  
Figure 5  
Right  
be secured to underside of Playard.  
7. The organizer can attach to any side of the playard. Insert the plastic  
hooks into the organizer as shown in (Fig 14 ). For best results, attach  
the organizer on the long side of the playard.  
Outside  
Inside  
8. Attach the organizer, by pushing the plastic clips down over the top  
rail. (Fig. 14 A). The maximum weight capacity of the organizer  
is 3 pounds.  
Figure 6  
9. To operate the brakes on the wheels, press downward on the brake  
lever as shown in figure 15. To release, lift upward on the lever.  
Figure 7  
Assembly is now complete and playard is ready to use.  
Figure 8  
Figure 10  
Figure 9  
Figure 11  
Figure 13  
Figure 14  
Figure 14A  
Figure 15  
Figure 12  
4
Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FOLDING PLAYARD  
1. Undo the 3 hook and loop straps holding mattress from underneath  
Playard floor. (If mattress is not used in the bassinet). Remove mattress  
and set aside.  
2. Grasp the center floor lock handle pushing down. Rotate the handle  
counter-clockwise about 90 degrees and lift upward until handle is as  
high as the top rails. Gather the four feet of the playard together so that  
they nearly touch each other. See figures 1 and 2.  
Rotate before  
lifting  
Figure 1  
NOTE: TOP RAILS OF THE PLAYARD ARE STILL IN THE  
“LOCKED” POSITION.  
3. Locate release button on the center of the bottom of each top rail. Lift  
slightly while squeezing button until the rail clicks. Push down on rail  
(while still holding release button in) until side forms a “U”. Repeat for  
remaining sides (Fig. 3).  
NOTE: If top rail(s) do not form the “U” completely do not force. Check  
the floor of your Playard to make sure all bottom rails are unlocked and  
pull up on middle handle of floor again. Repeat step 3.  
Figure 2  
4. Pull up on handle in center of Playard (Fig. 4). Gather legs of  
Playard together.  
5. Wrap mattress around Playard frame with padded side facing in.  
6. Secure the 3 hook and loop straps by feeding through loops on end of  
mattress and folding back onto itself (Fig. 5).  
7. Place Playard in carry bag so handle comes through opening  
between zippers.  
Figure 3  
WARNING: NEVER LEAVE INFANT IN  
PRODUCTWITH SIDES DOWN. Infant may  
roll into space between pad and loose mesh  
side causing suffocation.  
Figure 5  
Figure 4  
5
Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PLAY YARD BASSINET / CHANGING AREA  
WARNING:FAILURE TO FOLLOW THESE WARNINGS AND THE  
ASSEMBLY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR  
DEATH FROM ENTRAPMENT, STRANGULATION, SUFFOCATION, ETC.  
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their back to sleep, unless  
otherwise advised by your physician.  
• Always provide the supervision necessary for the continued safety of your child. When used for playing,  
never leave child unattended.  
• Adult supervision is always necessary when using your bassinet.  
Your playard, including side rails and bottom pad, must be fully erected prior to use.  
Top rails must be locked.  
• Bottom rails must be in flat, locked position.  
SUFFOCATION HAZARD: To help prevent suffocation from entrapment, use only the mattress provided  
®
by Baby Trend . Never use additional mattress or padding. Never use plastic shipping bags or other plastic  
film as mattress covers not sold and intended for that purpose. Avoid SUFFOCATION HAZARD caused by  
a loose sheet. A fitted sheet is recommended. The fitted sheet must fit the mattress tightly.  
STRANGULATION HAZARD: DO NOT place items with a string around child’s neck, such as hood  
strings or pacifier cords. DO NOT suspend string over bassinet or attach strings to toys.  
DO NOT add padding or other objects inside your bassinet which will permit a child to climb out.  
To prevent your child from falling out of the bassinet discontinue using your bassinet when  
your child is too active, able to climb out, weighs over 15 lbs.. (6.8 kgs.), or is over 4 months old.  
• Use changer with infant who’s weight is less than 18 lbs (8.2 kg ) and is less than 25 inches (63.5 cm) tall.  
• Discontinue use of changer if infant can push up on hands and knees or sit unassisted.  
DO NOT use a water mattress with this bassinet.  
• Use your bassinet with only one child at a time.  
• Keep bassinet away from stoves, heaters, campfires and other hazards.  
• Never place a child under the bassinet.  
• Never leave changer on top of playard with a child in the playard. Always flip changer to the outside  
when not in use.  
DO NOT store the bassinet in the playard.  
• The bassinet must be fully assembled and installed, including top rails and bottom pad, before using.  
• Before each use or assembly, inspect the playard and bassinet / changing area for damaged hardware,  
loose joints, missing parts or sharp edges. DO NOT use playard or bassinet if any parts are missing or  
broken. Call our Customer Service department at 1-800-328-7363 for replacement parts.  
To protect your child from falls and other injuries: always use safety belt when child is on the changing  
table, always stay within arm’s reach of your child when using the changing table, never leave child  
unattended.  
Baby Trend, Inc.  
1567 S. Campus Ave.  
Ontario, CA 91761, U.S.A.  
Customer Service Hot Line:  
1-800-328-7363  
8:00 A.M. to 4:30 P.M. Pacific Standard Time  
6
Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TO ASSEMBLE YOUR BASSINET  
NOTE: Playard MUST be in a locked set-up position before  
installing and using the bassinet feature.  
CONTENTS (Fig. 1):  
1 Nylon bassinet insert  
4 Metal support tubes 2 (male) (2 female)  
ASSEMBLY  
1. Insert the 2 female tubes into the two male tubes. (Fig. 2)  
2. Insert the 2 assembled tubes through the loops provided on the  
bassinet insert. (Fig. 3).  
3. Place assembled bassinet onto the Playard. Push down each of the  
bassinet supports onto the playard frame as shown in (Fig. 4).  
Figure 1  
NOTE: The printed warning label should be facing toward the  
inside of the bassinet so that it is readable.  
4. Place the Playard mattress into the bassinet with the padded side  
facing up (Fig. 5).  
Figure 2  
5. Connect the canopy to the Playard frame as shown in (Fig. 6)  
PLEASE NOTE THE CANOPY IS INTENDED FOR INDOOR  
USE ONLY.  
Figure 3.  
Figure 6.  
Figure 5.  
Figure 4.  
7
Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TO ASSEMBLE CHANGING AREA  
CONTENTS (Fig. 1):  
2 Long curved bars  
2 Short bars with connector knobs  
1 Changing area fabric  
WARNING:  
Figure 1  
Avoid serious injury or death:  
Always use restraint belt to prevent falls  
• Use changer with infant who’s weight is less  
than 18 lbs (8.2 kg ) and is less than 25 inches  
(63.5 cm) tall.  
• Discontinue use of changer if infant can push  
up on hands and knees or sit unassisted.  
Figure 2  
DO NOT carry changer with infant in it.  
• Always stay within arms reach of your child  
when using the changing area.  
WARNING: Strangulation Hazard  
Child can lift the changing table and get  
neck trapped between the changing table  
frame and the play yard frame. Never leave  
the changing table in place when the child is  
in the bassinet or the play yard. Always flip  
changer to the outside when not in use.  
Holes face  
down  
Figure 3  
WARNING FALL HAZARD:  
To prevent death or serious injury, always  
keep child within arm’s reach.  
Figure 4.  
ASSEMBLY  
1. Connect the two Long Curved Bars together as shown in figure 2.  
2. Insert the assembled Curved Bars into the Changing Area Fabric  
such that the holes in the ends of the Curved Bars face downward  
as shown in Figure 3.  
3. Slide the Curved Bars around inside the sleeve of the Changing  
Area Fabric.  
4. Connect the Short Bars with Connector Knobs to the Curved  
Bars as shown in figure 4. When assembling the Short Bars with  
Connector Knobs make sure that the knobs will be facing inward  
when assembled and the snap buttons are facing downward.  
Completed assembly  
Figure 5.  
8
Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE: Short bar with connector knobs should be facing  
inward.  
5. Place connector knob prongs into holes located on corner pieces  
of Playard (Fig. 5).  
6. Turn connector knobs counter clockwise to lock (Fig. 6).  
7. Flip changing area to inside of Playard (Fig.7).  
8. Snap flap from changing area to side of Playard (Fig. 8).  
9 Check that changing area is secure before using.  
Figure 5.  
Figure 6.  
Figure 7.  
Figure 8.  
REMOVALAND FOLDING CHANGING AREA  
REMOVAL  
1. Flip changing area to the outside of the Playard. Unsnap fabric flap  
of changing area from Playard.  
2. Twist connector knobs clockwise to unlock (Fig. 1).  
3. Remove changing area from Playard (Fig. 2).  
4. Disconnect the short bars from the curved bar by pressing on the  
snap buttons and pulling apart. Remove curved bar from changing  
area sleeve.  
Figure 1.  
The changing area is now ready for storage.  
Figure 2.  
9
Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REMOVAL OF BASSINET  
REMOVAL OF BASSINET  
1. Remove mattress from bassinet (Fig.1).  
2. Remove canopy (Fig. 2).  
3. Un snap all clips and lift bassinet out of playard (Fig. 3)  
The bassinet is now ready for storage.  
NOTE: Store bassinet and changing area with folded Playard  
in carry bag.  
Figure 1  
Figure 3  
Figure 2  
TO REMOVE CANOPY  
REMOVAL OF CANOPY  
To remove the bassinet canopy, pull upward on the ends of the canopy  
from the side of the playard. The canopy can be stored in the travel  
bag.  
USING THE MUSIC CENTER  
WARNING: Keep batteries out of child’s  
reach. Old and new batteries should not be  
mixed. Alkaline, standard carbon-zinc, and  
rechargeable nickel-cadium batteries should  
notbemixed. Removebatteriesbeforestoring  
music center for a long period of time.  
10  
Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MUSIC CENTER  
attach here  
The music center is designed to be attached to the playard. Flip  
changing table to the outside of the playard and attach music center  
to the corner as shown in figure 1.  
MUSIC OPERATION  
The music center requires 4 AA batteries. Please see figure 2 for  
battery installation. Unscrew the battery door screws and pull  
outward on the battery door. Install batteries as shown. Re-install  
battery door and secure with screws.  
Figure 1  
ON  
To active the unit, press the on/off button. Press button a second time  
OFF  
to enable voice activation. Press button a third time to switch unit off.  
To listen to SLEEP music, press the SLEEP button. You may use the  
vol  
vol  
_
+
_
previous / next button to change the song. The Vol  
or Vol  
buttons  
sleep  
control the units volume.  
To listen to PLAY music, press the PLAY button. You may use the  
previous / next button to change the song. The Vol  
control the units volume  
To listen to NATURE sounds, press the NATURE button you may use  
the previous / next button to change the sound. The Vol  
buttons control the units volume.  
+
_
vol  
vol  
or Vol buttons  
+
_
play  
vol  
vol  
+
or Vol  
nature  
VIBRATION  
To use the vibration button press down once  
to active the speed,  
Figure 2  
press again for a Medium speed and once more for the faster speed.  
Press to reduce the speed.  
NIGHT LIGHT  
To use the night light, press the  
brightness and is controlled by the  
button. The light has 3 settings of  
button.  
Recording Indicator  
rec  
play  
VOICE RECORDER  
rec  
play  
To use the Voice record function press the  
button and speak into the  
play  
microphone to record your 10 second voice message. Press  
the message.  
to hear  
rec  
vol  
ON  
VOICE ACTIVATION  
sleep play nature  
OFF  
To use the Voice Activation function press the OONFF button twice if the  
unit is power off. If the unit is already power on, press the  
once. The voice activation light will be illuminated when in voice  
activation mode. If your infant cries his/her voice will activate the  
sleep music to come on and play. When voice activation is enabled,  
sleep mode is active for 2 hrs.  
nxt  
prev  
ON  
OFF  
vol  
ON  
Voice Activation  
Indicator  
button  
OFF  
mp3  
input  
MP3 FUNCTION  
MP3 Indicator  
mp3  
Use the input jack to attach your MP3 player into the unit . Press the  
button to select the MP3 input. Your MP3 music will then be played  
thru the unit and will over-ride the unit’s music. To listen to the unit’s  
input  
music, depress the  
player.  
button. Volume will be controlled by the MP3  
IF YOU EXPERIENCE ANY DIFFICULTY IN USING THIS PRODUCT, PLEASE CONTACT OUR CUSTOMER  
SERVICE DEPARTMENT AT 1-800-328-7363 BETWEEN THE HOURS OF 8:00 A.M. AND 4:30 P.M. PACIFIC  
STANDARD TIME FOR ASSISTANCE.  
11  
Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

3Com PDAs Smartphones V User Manual
AeroGarden Greenhouse Kit 100629 User Manual
Audiovox Automobile Electronics AS GMDLT03 User Manual
Avenview TV Cables FO HDM XX MM User Manual
AVerMedia Technologies DVR EB1304 NET User Manual
Avital Automobile Alarm 3300L User Manual
Avital Automobile Alarm G5103 User Manual
Axis Communications Security Camera AXIS 232D+ 50 Hz User Manual
Axis Communications Security Camera P3363 VE User Manual
Behringer Music Mixer 302USB User Manual