Smart Switch
Model 232SS2
Document No. 232SS21600
This product Designed and Manufactured
of domestic and imported parts by
International Headquarters
B&B Electronics Mfg. Co. Inc.
707 Dayton Road -- P.O. Box 1040 -- Ottawa, IL 61350 USA
Phone (815) 433-5100 -- General Fax (815) 433-5105
1992 B&B Electronics -- Revised April 2000
Cover Page
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Chapter 1: INTRODUCTION...............................................1
Checklist.................................................................................2
Chapter 2: SETUP ...............................................................3
Port Configuration ..................................................................4
Serial Data Configuration.......................................................5
Smart Switch Operation .........................................................6
Programming the Second Character .....................................7
Binary File Transfer................................................................7
Smart Switch/Port Combiner Mode........................................8
Specifications.......................................................................11
Chapter 3: SOFTWARE....................................................12
Introduction ..........................................................................12
Windows SSwitch.................................................................12
DOS SSTSR ........................................................................13
Parameters...........................................................................15
Default Values......................................................................16
Help Screen .........................................................................16
Un-Install..............................................................................16
Selecting Ports.....................................................................16
Hot Key Method....................................................................17
Command Line Method........................................................17
APPENDIX A: ASCII Character Codes...........................A-1
APPENDIX B: Cable Charts............................................B-1
232SS21600 Manual
Table of Contents
i
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: INTRODUCTION
The RS-232 Four Port Smart Switch/Port Combiner, Model
232SS2, allows one RS-232 host device to connect to as many as
four RS-232 devices. The switch can be controlled in two different
ways. The first way is referred to as smart switch mode. In this
mode, the switch is controlled by sending a programmable preamble
code to the "Master" port of the 232SS2. The other way the switch
can be controlled is referred to as port combiner mode. In port
combiner mode, a slave port can gain access to the master port by
asserting a handshake line. If none of the slave ports have their
handshake line asserted, the switch can be controlled using the
preamble code.
The master port can be configured as a DTE or DCE port by an
internal switch setting. If the master port is configured as a DTE port,
the four slave ports will become DCE ports. The 232SS2 supports
the following signals: TD, RD, RTS, CTS, DSR, DCD, and DTR.
The 232SS2 has an enhanced mode which offers special timer
features. The timer features can be used to prevent slave devices
from receiving preamble commands, inadvertently switching from
binary/graphic file transfers, and inactive slave devices from holding
control of the master port.
The 232SS2 will work with baud rates from 1200 to 115,200
bps; 7 or 8 data bits; even, odd or no parity; and 1 or 2 stop bits
(7,N,1 is not allowed).
NOTE: The data format and rates mentioned are used to switch
the 232SS2. The communication between the devices can use any
format or data rate.
There are four LED's on the 232SS2 to indicate which port is
connected to the master port. The master port has a DB-25S female
connector and the slave ports have DB-25S female connectors. The
232SS2 requires 12Vdc at 100ma. which is provided through a
2.5mm power jack.
232SS21600Manual
1
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104
Download from Www.Somanuals.com. All Manuals Search And Download.
Checklist
Examine the shipping carton and contents for physical damage.
If damage is found, file a claim with the shipper immediately.
The following equipment should be in the shipping carton:
1. RS-232 Smart Switch
2. Instruction Manual
3. (2) 3.5" floppy disks
If any of the items above are not in the shipping carton contact
the shipper immediately.
2
232SS21600 Manual
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: SETUP
The 232SS2 is set up using an eight-position dipswitch. This
dipswitch is used to set the communication format, port
configuration, smart switch/port combiner mode and to
enable/disable the enhanced features. To change the settings on
the switch, remove the power from the unit, and remove the screws
(2) from the bottom of the 232SS2. The dipswitch is located on the
top of the PC board (side with LEDs) and is labeled “SW1.” The
other dipswitch, labeled “SW2” is used to set the second character
of the preamble. After the switches have been set to match your
requirements, you can put the unit back together. Table 1 shows the
settings for dipswitch “SW1”.
Table 1. Communication & Port Setup
Dipswitch SW1
1
2
3
4
5
6
7
8
Setting
0
0
0
X
X
X
X
X
1200 Baud
1
0
1
0
1
0
1
X
X
X
X
X
X
X
X
X
X
0
1
1
0
0
1
1
X
X
X
X
X
X
X
X
X
X
0
0
0
1
1
1
1
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
0
X
X
X
X
X
X
X
X
X
0
X
X
X
X
X
X
X
X
X
X
X
0
X
X
X
X
X
X
X
X
X
X
X
X
X
0
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
0
2400 Baud
4800 Baud
9600 Baud *
19.2K Baud
38.4K Baud
57.6K Baud
115.2K Baud
Enhanced Disabled *
Enhanced Enable
8 Data Bits *
1
X
X
X
X
X
X
X
X
1
7 Data Bits
X
X
X
X
X
X
Parity Disabled *
Parity Enabled
Smart Switch Mode*
Port Combiner Mode
DCE master port *
DTE master port
1
X
X
X
X
1
X
X
1
0 = OFF
1 = ON
X = DON'T CARE
* = FACTORY DEFAULT
232SS21600Manual
3
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104
Download from Www.Somanuals.com. All Manuals Search And Download.
Port Configuration
In order to determine the proper port configuration of the
232SS2, it is necessary to have a basic understanding of the terms
DCE and DTE. RS-232 was designed, using DB-25 connectors, for
connecting a DTE (Data Terminal Equipment) device to a DCE
(Data Communication Equipment) device. Each device will have
inputs on pins that correspond to outputs on the same pins of the
other device. For example, a DTE device will transmit data out on
pin 2 (on a DB-25) and a DCE device will receive data in on pin 2
(on a DB-25). IBM PCs and serial printers are DTE devices,
modems are DCE devices.
If an IBM PC (DTE device) is going to be connected to the
232SS2 master port, the master port should be configured as a DCE
port. If a modem (DCE device) is going to be connected to the
master port, it should be configured as a DTE port.
The master port can be configured as a DCE port (data received
on pin 2) or a DTE port (data received on pin 3) by setting dipswitch
“SW1”, position 8. To configure the master port as a DCE port, move
dipswitch “SW1”, position 8, to the "OFF" position. When the master
port is configured as a DCE port, ports A, B, C, & D will become
DTE ports (Refer to Table 2). To configure the master port as a DTE
port move dipswitch “SW1”, position 8, to the "ON" position. When
the master port is configured as a DTE port, ports A, B, C, & D will
become DCE ports (Refer to Table 3). Always power down the
smart switch when changing switch settings.
4
232SS21600 Manual
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 2. DCE MASTER PORT CHART
Master Port A,B,C & D Ports
(DCE)
Signal
(DTE)
Pin# Direction
Description
Pin# Direction
2
3
4
5
6
7
8
20
Input
Output
Input
Output
Input
Transmit Data (TD)
Receive Data (RD)
Request to Send (RTS)
Clear to Send (CTS)
DCE Ready (DSR)
Signal Ground (SG)
2
3
4
5
6
7
8
20
Output
Input
Output
Input
Output
GROUND
Input
GROUND
Output Recv. Line Detect (DCD)
Input DTE Ready (DTR)
Output
Table 3. DTE MASTER PORT CHART
Master Port
A,B,C & D Ports
(DCE)
(DTE)
Signal
Pin# Direction
Description
Pin# Direction
2
3
4
5
6
7
8
20
Output
Input
Output
Input
Output
GROUND
Input
Transmit Data (TD)
Receive Data (RD)
Request to Send (RTS)
Clear to Send (CTS)
DCE Ready (DSR)
Signal Ground (SG)
Recv. Line Detect (DCD)
DTE Ready (DTR)
2
3
4
5
6
7
8
20
Input
Output
Input
Output
Input
GROUND
Output
Input
Output
The 232SS2 supports the following RS-232 signals: TD, RD, SG,
RTS, CTS, DSR, DCD, and DTR.
The Smart Switch selects port A as the default port at power up.
Serial Data Configuration
In order for the host device that is connected to the master port
to select any of the four ports, the Smart Switch must be set to
match the host's communication format. Dipswitch “SW1” is used to
select the communication format of the Smart Switch. Switch
positions 1 through 3 select the baud rate. Switch position 5 selects
7 or 8 data bits. Switch position 6 determines if parity is enabled or
disabled.
NOTE: A data format of 7 data bits, no parity and one stop is
not allowed.
232SS21600Manual
5
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104
Download from Www.Somanuals.com. All Manuals Search And Download.
Switch position 8 selects the port configuration, see section titled
"Port Configuration". Refer to Table 1.
switch when changing switch settings.
power down the smart
Always
Smart Switch Operation
Smart Switch mode is selected when dipswitch “SW1” position 7
is “Off.” In Smart Switch mode, the 232SS2 is constantly looking for
the three character preamble code by monitoring the data that is
being received on the master port from the host device. The 232SS2
requires a three character preamble code to turn on and off a port.
The first character must be the ASCII escape character (decimal
27). The second character is user programmable by setting
dipswitch “SW2”. “SW2” comes from the factory programmed to the
ASCII character STX (decimal 2). The third character should be the
ASCII upper case letters "A", "B", "C" or "D" (decimal 65, 66, 67, or
68 respectively) to select those ports. To turn off the selected port
the third character should be the ASCII EOT character (decimal 4).
For instance, to turn on port B you would send:
ESC STX B
If you were writing a program in BASIC to control the Smart
Switch you would form a string like this:
SWB$ = CHR$(27) + CHR$(2) + "B"
You could then send SWB$ to select port B. Similar strings
could be used for turning on the other ports. To turn off the ports the
string might look like this:
TOFF$ = CHR$(27) + CHR$(2) + CHR$(4)
When you are done with a port you can either select a new one
directly or turn off the selected port and then turn on the next one.
We recommend that you turn off the selected port before selecting
the next one. The turn off command consists of three characters that
are non-printing (ESC STX EOT). If port A is selected and you send
the command to select port B, all three characters (ESC STX B) will
pass through the A port since it is still selected and the letter B will
show up on your port A device. For information on preventing
command codes from being received by slave devices, refer to the
Enhance Mode section.
NOTE: There is no delay through the Smart Switch and the
data is not buffered.
6
232SS21600 Manual
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming the Second Character
The second character comes programmed as the ASCII STX
character (decimal 2). You can change this to any 8-bit character
you wish by reprogramming dipswitch “SW2”. “SW2” is an eight-
position switch with each position equal to a certain weight. Refer to
“Setup” for instructions on removing the cover to access “SW2”.
Table 4 shows the weight chart for “SW2”.
Table 4. Programmable Character Setting
Dipswitch SW2* WEIGHT
1
2
3
4
5
6
7
8
1
2
4
8
16
32
64
128
*Factory Default -- ASCII “STX” character
(decimal 2), SW2 position 2 is only one ON.
If you wish to use the letter "U" as the second character, which
has a decimal value of 85, you would turn on switches 1, 3, 5, and 7
(1 + 4 + 16 + 64 = 85). Caution should be used when selecting the
second character, so that by itself, or with the ESC character in front
of it, it is not a valid command to any of the devices on the port. For
instance, on some printers ESC @ is the reset command. If you
tried to use the @ symbol (decimal 64) for the second character you
could reset your printer every time the preamble code was sent.
Note also that if your communication configuration is set for 7 data
bits you cannot use the eighth bit of SW2. For a list of the ASCII
character codes and their decimal values refer to Appendix A.
Binary File Transfer
A simple method of using the Smart Switch to transfer binary
files without the concern of it accidentally disconnecting, is to set the
file transfer at a baud rate different from the baud rate of the Smart
Switch. When transferring files at a different baud rate, the Smart
Switch will stay connected from the last preamble code.
232SS21600Manual
7
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104
Download from Www.Somanuals.com. All Manuals Search And Download.
Smart Switch/Port Combiner Mode
This mode allow Ports A-D to select the master port using a
handshake line. It also allows selection from the master port via the
preamble code described in the Smart Switch Only Mode section.
Position 7 of “SW1” must be ON to be in port combiner mode. When
a handshake line goes high on any of the four ports, it will establish
a connection from that port to the master port. This works on first-
come-first-serve basis. If multiple ports have their handshake lines
high, the port that has been waiting the longest will be next to be
connected to the master port. For example, (Initial conditions -- no
slave ports with handshake lines asserted.) in chronological order,
Port C asserts its handshake line, Port A asserts its handshake line,
Port D asserts its handshake line and then Port C disasserts its
handshake line. When Port C asserts its handshake line, a
connection will be made between the master port and Port C. When
Port C disasserts its handshake line, Port C will be disconnected
and Port A will be connected to the master port. When Port A
disasserts its handshake, Port A will be disconnected and Port D will
be connected to the master port.
The handshake line that is used to connect to the master port
depends on the configuration of the master port (which in turn
determines the configuration of the slave ports). If the master port is
configured as a DTE port, then the slave ports are configured as
DCE, and RTS must be raised by the device (which is DTE) to
connect to the master port. If the master port is configured as a DCE
port, then the slave ports are configured as DTE and CTS must be
raised by the device (which is DCE) to connect to the master port.
For example, port A is configured as a DCE port (slave device is
DTE), in order to establish a connection to the master port, the
device must set RTS high (assert). The 232SS2 would recognize
this as a prompt for connection to the master port. The connection
would be dropped as soon as RTS from the device is lowered. The
devices on ports B-D may raise RTS at any time to request a
connection. However, if port A is connected to the master port, any
data sent from the devices on ports B-D to the 232SS2 will be lost.
The 232SS2 does not have any buffering.
NOTE: When a port is selected via the Master Port, the
handshake lines will be ignored until the Master Port sends
the turn off code. When the Master Port is selected by a
handshake line, all preamble codes will be ignored.
8
232SS21600 Manual
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104
Download from Www.Somanuals.com. All Manuals Search And Download.
A typical application would be to have RTS and CTS tied together
on the master port. When RTS (assuming DTE slave device) on port
A (configured as DCE) is asserted, CTS on port A will be asserted
when a connection is established. If a port is not connected to the
master port, then CTS on that port will remain low. Therefore, a port
can monitor the handshake line to determine if a connection has
been established.
Enhanced Mode -- Timer Features
The 232SS2 has an enhanced mode, which offers special timer
features. The timer features can be used to prevent slave devices
from receiving preamble commands, inadvertent switching from
binary/graphic file transfers, and inactive slave devices from holding
control of the master port. The timer has two different modes: an
inactivity mode and an inadvertent switch mode. When in inactivity
mode, the 232SS2 will monitor the data lines. If there is no activity
for the specified time, the selected slave port will be disconnected
from the master port. When in inadvertent switch mode, the
232SS2 will ignore switching commands for the specified period of
time. After this time has expired, the selected slave port will be
disconnected from the master port.
The timer functions are enabled via a dipswitch setting and
through software commands. Dipswitch SW1 position 4 must be
ON for the 232SS2 to be in enhanced mode. The software
commands follow the same format as preamble codes used for
switching. There are two commands used to set the timer functions:
Set Timer Mode and Set Timer Value. These commands require an
additional byte for data. The Set Timer Value command requires the
third byte to be an ASCII “T” character. The data byte (fourth byte)
must be a value between ASCII “0” and ASCII “9”. A value of “0” is
used to disable the timer. Refer to Table 3 for timer values. For
example, sending the following string to the 232SS2 will set the
timer value to 5 seconds (assuming programmable character is the
factory default of 2).
SetTV$ = CHR$(27) + CHR$(2) +”T” + “6”
The “T” tells the 232SS2 it is the set timer value command and the
“6” indicates which timer value to use.
232SS21600Manual
9
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3 - Timer Values
Data Byte
Value
0
1
2
3
4
5
6
7
8
9
timer disabled
10ms
25ms
100ms
500ms
1 s
5 s
30 s
1 min.
5 min.
The Set Timer Mode command requires the third byte to be an
ASCII “M”. If the data byte (fourth byte) is an ASCII “0”, zero
(default), the timer will be setup as an inactivity timer. For example:
Sending the following string to the 232SS2 will set up the timer as an
inactivity timer (assuming programmable character is the factory
default of 2).
SetTM$ = CHR$(27) + CHR$(2) +”M” + “0”
The “M” tells the 232SS2 it is the set timer mode command and the
“0” indicates to set up the timer as a inactivity timer. When the timer
is configured as an inactivity timer, the 232SS2 will monitor the data
lines (TD & RD) for data. If there is no activity for the specified timer
value, the slave port that is connected to the master port will be
disconnected. In smart switch mode, the inactivity timer can be used
to prevent the preamble codes from being received by the slave
devices. In port combiner mode, the inactivity timer can be used to
prevent devices from tying up the master port. For example (port
combiner mode), all the slave ports have their handshake lines
asserted. The device on Port C has its handshake line asserted and
is currently connected to the master port, but has not been
transmitting or receiving data. When the inactivity timer expires, Port
C will be disconnected and the next slave port will then be
connected to the master port (following the first-come-first-serve
rule). Port C will then be placed at the “end of the line”.
If the data byte of the Set Timer Mode command is an ASCII “1”,
the timer will be setup to ignore switching commands. Sending the
following string to the 232SS2 will set up the timer to ignore
switching commands. (Assuming programmable character is the
factory default of 2).
SetTM$ = CHR$(27) + CHR$(2) +”M” + “1”
10
232SS21600 Manual
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104
Download from Www.Somanuals.com. All Manuals Search And Download.
The “M” tells the 232SS2 it is the set timer mode command and the
“1” indicates to set up the timer to ignore switching commands.
When the timer is configured in this mode, the 232SS2 will not
accept any switching commands (“A”, ”B”, ”C”, ”D”, or “EOT”) for the
specified timer value. After the timer has expired, the slave port that
is connected to the master port will be disconnected. This feature is
useful to prevent inadvertent switching during binary/graphic type file
transfers. For example (smart switch mode): The timer is
configured to ignore switching commands for 5 seconds. The select
Port D command is sent to the 232SS2. Once Port D is connected a
file of unknown data type (so file may or may not contain a switching
command sequence) is to be transferred through the 232SS2. For a
period of 5 seconds after Port D is connected, no switching
commands will be accepted. As long as the file transfer takes less
than 5 seconds, there is no chance the 232SS2 will inadvertently
switch ports.
Table 4 - 232SS2 Commands
Command Characters
Function
1st
2nd
3rd
4th
Comments
Select Port A
ESC
X*
“A”
NU**
Switching
Command
Switching
Command
Switching
Command
Switching
Command
Switching
Command
Enhanced
Mode
Select Port B
Select Port C
Select Port D
Deselect Port
Set Timer Value
Set Timer Mode
ESC
ESC
ESC
ESC
ESC
ESC
X*
X*
X*
X*
X*
X*
“B”
“C”
NU**
NU**
“D”
NU**
EOT
“T”
NU**
“0”-”9”
“0”,”1”
“M”
Enhanced
Mode
*X represents the programmable character set by dipswitch SW2
**NU = Not Used
Specifications
Model:
Size:
232SS2
6.2 x 8.0 x 2.5hin
Power: 12Vdc to 16Vdc @ 100mA
232SS21600Manual
11
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: SOFTWARE
Introduction
The 232M`SS2 comes with two application programs that can
be used to switch between ports. Each comes on a separate floppy
disk. Either can be used independently as the final application or for
testing the functionality of the hardware.
The SSwitch program is a Windows program that allows you to
switch ports with buttons on a Windows interface, or from the DOS
command line. It will run on Windows 95, 98, or Windows NT 4.0
with service pack 3 installed. When the software is installed, an
example file, SSWVb6.txt, is also placed in the same directory. This
is a text file with Visual Basic sample code. It gives examples on
how to open the port, assemble switching commands, and send
them out the port. It can be accessed by selecting
START/PROGRAMS/B&B Electronics/SSWITCH/Sample Code.
The Smart Switch, Terminate and Stay Resident (SSTSR)
Program (IBM PC or Compatible), is a DOS only application which
allows the user to change Smart Switch ports either through the
command line or by hitting a sequence of keys at the same time,
referred to as hot keys. SSTSR program requires 1K of memory.
Windows SSwitch
Installation
To install the SSwitch Program (Windows 95/98 & NT)
• From START/ SETTINGS/ CONTROL PANEL
• Select Add/Remove Programs
• Insert the Smart Switch for Windows disk and select Install
• Follow the Installation prompts to complete the installation
Running SSwitch
The SSwitch program can be launched from the desktop
shortcut or from the Start/Programs/B&B Electronics/SSwitch
directory if the default directory was selected during installation.
The Smart Switch software configuration can be changed in
the SSwitch program by selecting Ports/Configuration from the
menu. You change port selection by clicking on the option box or by
using the up/down arrow keys. The port selection can also be
changed at the command line by typing SSwitch and the letter
representing that port. For example, to change to port B you would
enter SSwitch B at the command line. The letter N (none) is used to
close all the ports.
12
232SS21600 Manual
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104
Download from Www.Somanuals.com. All Manuals Search And Download.
To Uninstall SSwitch.exe
•
•
•
•
From START/ SETTINGS/ CONTROL PANEL
Select Add/ Remove Programs
Select SSwitch from the list of programs
Click on the Add/Remove button
DOS SSTSR
Installation
To Install the SSTSR Program (DOS)
If A drive is your floppy drive:
•
•
•
Place the Smart Switch for DOS disk in drive A
At the DOS prompt
Type a:\INSTALL.exe and press the ENTER key.
The following files will be located on your hard drive:
1)SSTSR.EXE - The executable file for the Smart Switch.
2)SETUP.EXE - Configuration program for the SSTSR.
There are two methods to begin the SSTSR program. The first
and preferred way is to use the SETUP.EXE program and the
second is through the SSTSR.COM file.
1) SETUP.EXE Method (preferred)
If the software was installed on your hard drive follow these
steps:
• Type C: and press the ENTER key.
• Type CD\SS and press the ENTER key.
To begin the SSTSR program follow these steps:
• Type SETUP and press the ENTER key. You will be prompted
for parameters (for a description refer to the Parameters
section) that are necessary for the SSTSR to communicate
with the Smart Switch. The value in [ ] are the default values. If
this value is desired, just press the ENTER key.
232SS21600 Manual
13
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104
Download from Www.Somanuals.com. All Manuals Search And Download.
Enter Port Address [02F8]:
Enter Baud Rate ( 1 = 150 2 = 300 3 = 600
4 = 1200 5 = 24006 = 4800
7 = 9600 8 = 19200) [7]:
Enter Parity (0 = No 1 = Odd 2 = Even) [0]:
Enter Number of Data Bits ( 7 = Seven Data Bits
8 = Eight Data Bits) [8]:
Enter Smart Switch Second Char (Decimal Value) [2]:
Enter Hot Key Sequence (1 = <LftShift><Alt><A|B|C|D|N>
2 = <Rht Shift><Alt><A|B|C|D|N>
3 = <Lft Shift><Alt><1|2|3|4|N>
4 = <Rht Shift><Alt><1|2|3|4|N>
5 = <CTRL><ALT><A|B|C|D|N>
6 =<CTRL><ALT><1|2|3|4|N>)[1]:
At this point a file called GO.BAT will be created.
•
Type GO and press the ENTER key.
Once the GO.BAT file is created, every time you wish to begin
the SSTSR all that you need to do is type GO and press the ENTER
key. If you need to change any of the settings of the SSTSR simply
run the SETUP.EXE program again to create a new GO.BAT file.
2) SSTSR.EXE Method
The SSTSR.EXE method requires the same parameters (for a
description refer to the Parameters section) as the SETUP.EXE
method, except that they are all specified through the command line.
Each of these parameters begins with a command symbol followed
by an option as defined in the following table.
Command Description
A or a
Options
Hexadecimal Address (0 - FFFFh)
Port Address
Baud Rate
1 = 150 2 = 300
3 = 600
B or b
4 = 1200 5 = 2400 6 = 4800
7 = 9600 8 = 19200
Number of Data
Bits
7 = 7 Data Bits 8 = 8 Data Bits
D or d
Parity
User Defined Char.
Hot Key
0 = No
Decimal (0 - 255)
1 = Odd
2 = Even
P or p
U or u
H or h
1 = <Left Shift><ALT><A|B|C|D|N>
2 = <Right Shift><ALT><A|B|C|D|N>
3 = <Left Shift><ALT><1|2|3|4|N>
4 = <Right Shift><ALT><1|2|3|4|N>
5 = <CTRL><ALT><A|B|C|D|N>
6 = <CTRL><ALT><1|2|3|4|N>
14
232SS21600 Manual
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104
Download from Www.Somanuals.com. All Manuals Search And Download.
If the software was installed in the default directory:
• At the DOS prompt Type C: and press the ENTER key.
• Type CD\232MSS2 and press the ENTER key.
To begin the SSTSR program (the following will be used as an
example):
Port Address = 03F8 Parity = Odd
Baud = 9600
User Defined Char. = 8
Data Bits = 8 Hot Key Sequence = 4
• Type SSTSR A03F8 B7 D8 P1 U8 H6 and press the ENTER
key.
Using this method, every time you want to install the SSTSR
with different parameter settings than the default (refer to the Default
Values section), the missing parameter must be specified.
Parameters
The Port Address is the address where the serial
communications port is located.
Some of the typical port addresses are as follows:
Port
Address
03F8h
02F8h
03E8h
02E8h
COM 1
COM 2
COM 3
COM 4
The Baud Rate is the speed at which communication takes
place between the SSTSR and the Smart Switch. It must be
specified so that it is equal to SW1 on the Smart Switch.
The Number of Data Bits is the length of each character that
gets sent from the SSTSR to the Smart Switch. This value must be
specified so that it is equal to SW2 on the Smart Switch.
The Parity is a method of error detection that takes place during
the transmission of data between the SSTSR and the Smart Switch.
This value must be specified so that it is equal to SW2 on the Smart
Switch.
The User Defined Character must be set so that it is equal to
SW3 on the Smart Switch.
232SS21600 Manual
15
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104
Download from Www.Somanuals.com. All Manuals Search And Download.
The Hot Key is a sequence of three keys that must be pressed
simultaneously to switch from one Smart Switch Port to another. For
example, the hot key sequence, <Left Shift> <ALT> <A|B|C|D|N>
states that the left shift, Alt, and either A, B, C, D, or N must be
pressed at the same time to select the corresponding Smart Switch
Port. N turns off all Smart Switch ports.
Default Values
If you type SSTSR on the command line with no parameters, or
omit any parameters, the default value of the missing parameter will
be used. The default values are:
Description
Port Address
Baud Rate
Default Value
02F8h (COM 2)
7 = 9600
0 = No Parity
Parity
8 = 8 Data Bits
Data Bits
2 = STX (CTRL B)
1 = <Left Shift><ALT><A|B|C|D|N>
Second Character
Hot Key Sequence
Help Screen
If you are installing the SSTSR using the SSTSR.COM method,
you can type SSTSR ? and press the ENTER key to obtain a list of
the commands and their options.
Un-Install
The SSTSR may be un-installed easily by typing SSTSR - and
pressing the ENTER key. In some cases the SSTSR will not un-
install. This may be caused by another terminate and stay resident
(TSR) being installed after it. To un-install the SSTSR when this
occurs, the other TSR must first be un-installed, then the SSTSR
can be un-installed normally.
Selecting Ports
There are two different ways in which a Smart Switch port is
selected, either through the command line or by pressing the
predefined hot key sequence after the SSTSR was installed. When
a request to change ports is made, using either method, first the
current port is turned off, then the port selected is turned on. The
two methods are described as follows:
16
232SS21600 Manual
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104
Download from Www.Somanuals.com. All Manuals Search And Download.
Hot Key Method
This method enables the user to select any Smart Switch port by
pressing a predefined sequence of keys at the same time after the
SSTSR is installed (refer to Program Installation).
Example:
If Hot Key sequence <Lft Shift><Alt><A|B|C|D|N> was selected,
to change ports you would press at the same time:
Left Shift - Alt - A ..... to select port A
Left Shift - Alt - B ..... to select port B
Left Shift - Alt - C ..... to select port C
Left Shift - Alt - D ..... to select port D
Left Shift - Alt - N ..... to turn off all ports
Command Line Method
This method enables the user to select any Smart Switch port
through the command line. To specify a Smart Switch port through
the command line, you would type SSTSR followed by the X
command symbol and the letter of the port.
Example:
To change to Smart Switch port '"C" you would type SSTSR XC
at the Dos prompt and press the ENTER key.
Before a Smart Switch port is changed, a check is made to
determine if the port is busy transmitting. If the port is busy the
STSR will generate a tone to notify you that the port is busy and that
a port change cannot be made.
CAUTION: If the software package you are using for
transmission is running at a fast baud rate (57600), the
SSTSR may not detect the Smart Switch port as busy and the
transmission could be interrupted.
The SSTSR does not detect when the Smart Switch port is
receiving data. Therefore, if data is being received, the Smart Switch
port may still be changed.
232SS21600 Manual
17
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX A: ASCII Character Codes
DECIMAL to HEX to ASCII CONVERSION TABLE
DEC HEX ASCII KEY DEC HEX ASCII DEC HEX ASCII DEC HEX ASCII
0
0
1
NUL ctrl @ 32
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
SP
!
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
@
A
B
C
D
E
F
G
H
I
96
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
7D
7E
7F
`
a
b
c
d
e
f
1
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
ctrl A
ctrl B
ctrl C
ctrl D
ctrl E
ctrl F
ctrl G
ctrl H
ctrl I
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
97
2
2
“
98
3
3
#
$
%
&
'
99
4
4
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
5
5
6
6
7
7
g
h
i
8
8
(
9
9
HT
)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
A
LF
ctrl J
ctrl K
ctrl L
ctrl M
ctrl N
ctrl O
ctrl P
ctrl Q
ctrl R
ctrl S
ctrl T
ctrl U
ctrl V
*
J
j
B
VT
+
,
K
L
k
l
C
FF
D
CR
-
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
[
m
n
o
p
q
r
E
SO
.
F
SI
/
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
DLE
DC1
DC2
DC3
DC4
NAK
SYN
0
1
2
3
4
5
6
7
8
9
:
s
t
u
v
w
x
y
z
{
ETB ctrl W
CAN
EM
ctrl X
ctrl Y
ctrl Z
ctrl [
SUB
ESC
FS
;
ctrl \
<
=
>
?
\
|
GS
ctrl ]
]
}
RS
ctrl ^
ctrl _
^
~
DEL
US
_
232SS21600 Manual
Appendix A
A-1
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX B: Cable Charts
All charts will indicate if the Master Port of the 232SS2 should be
configured as a DCE port or a DTE port. Refer to the Port
Configuration section of the manual for information on Master Port
configurations.
Chart 1. IBM PC DB25 Connector to Master Port
Straight Through Connection
IBM PC
232SS2
Serial Port
Signal
Master Port (DCE)
DB25 Connector
Direction
----------->
<-----------
----------->
<-----------
<-----------
GROUND
<-----------
----------->
DB25 Connector
2
3
4
5
6
7
8
20
2
3
4
5
6
7
8
20
Chart 2. IBM PC DB9 Connector to Master Port
Straight Through Connection
IBM PC
232SS2
Serial Port
Signal
Master Port (DCE)
DB9 Connector
Direction
<-----------
<-----------
----------->
----------->
GROUND
<-----------
----------->
<-----------
DB25 Connector
1
2
3
4
5
6
7
8
8
3
2
20
7
6
4
5
232SS21600 Manual
Appendix C
C-1
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104
Download from Www.Somanuals.com. All Manuals Search And Download.
Chart 3. Modem DB25 Connector to Master Port
Straight Through Connection
Async Modem
232SS2
Serial Port
Signal
Master Port (DTE)
DB25 Connector
Direction
<-----------
----------->
<-----------
----------->
GROUND
----------->
<-----------
DB25 Connector
2
3
4
5
7
2
3
4
5
7
8
20
8
20
Chart 4. IBM PC DB25 Connector to Ports A - D (DTE)
Master port DCE, Slave port DTE.
Null Modem Connection
IBM PC
232SS2
Serial Port
Signal
Ports A - D (DTE)
DB25 Connector
Direction
----------->
<-----------
----------->
<----------
<----------
GROUND
----------->
DB25 Connector
2
3
4
3
2
5
4
20
7
5
6 & 8
7
20
6 & 8
C-2
Appendix C
232SS21600 Manual
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104
Download from Www.Somanuals.com. All Manuals Search And Download.
Chart 5. IBM PC DB25 Connector to Ports A - D (DCE)
Master port DTE, Slave ports DCE.
Straight Through Connection
IBM PC
232SS2
Serial Port
Signal
Ports A - D (DCE)
DB25 Connector
Direction
----------->
<-----------
----------->
<-----------
<-----------
GROUND
<-----------
----------->
DB25 Connector
2
3
4
5
6
7
8
20
2
3
4
5
6
7
8
20
.
Chart 6. IBM PC DB9 Connector to Ports A - D (DTE)
Master port DCE, Slave port DTE.
Null Modem Connection
IBM PC
232SS2
Serial Port
Signal
Ports A – D (DTE)
DB9 Connector
Direction
<-----------
<-----------
----------->
----------->
GROUND
----------->
<-----------
DB25 Connector
1 & 6
20
2
3
2
3
4
5
7
8
6 & 8
7
5
4
232SS21600 Manual
Appendix C
C-3
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104
Download from Www.Somanuals.com. All Manuals Search And Download.
Chart 7. IBM PC DB9 Connector to Ports A - D (DCE)
Master port DTE, Slave port DCE.
Straight Through Connection
IBM PC
232SS2
Serial Port
Signal
Ports A – D (DCE)
DB9 Connector
Direction
<-----------
<-----------
----------->
----------->
GROUND
<-----------
----------->
<-----------
DB25 Connector
1
2
3
4
5
6
7
8
8
3
2
20
7
6
4
5
C-4
Appendix C
232SS21600 Manual
B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104
Download from Www.Somanuals.com. All Manuals Search And Download.
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFACE STATEMENT
Class A Equipment
This equipment has been tested and found to comply with the
limits for Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case the user
will be required to correct the interference at personal expense.
FCC Class A Equipment Statement
Download from Www.Somanuals.com. All Manuals Search And Download.
|