Axis Communications Security Camera Q604 User Manual

AXIS Q604 Series  
AXIS Q6042 PTZ Dome Network Camera  
AXIS Q6044 PTZ Dome Network Camera  
AXIS Q6045 PTZ Dome Network Camera  
Installation Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Australia/New Zealand  
223 69 Lund  
Sweden  
Tel: +46 46 272 18 00  
Fax: +46 46 13 61 30  
This digital equipment fulfills the requirements for RF  
emission according to the Class A limit of AS/NZS CISPR 22.  
The product shall be connected using a shielded network  
cable (STP) that is properly grounded. Notice! This is a  
Class A product. In a domestic environment this product  
may cause RF interference, in which case the user may be  
required to take adequate measures.  
Support  
Should you require any technical assistance, please contact  
your Axis reseller. If your questions cannot be answered  
Japan  
この装置は、クラスA 情  
報技術装置です。この装  
置を家庭環境で使用すると電波妨害 を引き起こす  
ことがあります。この場合には使用者が適切な対  
immediately, your reseller will forward your queries through  
the appropriate channels to ensure a rapid response. If you  
are connected to the Internet, you can:  
を講ずるよう求され ることがあります。 本  
download user documentation and software updates  
製品  
は、シールドネットワークケーブル(STP)を  
地し  
find answers to resolved problems in the FAQ database.  
使用して接  
続してください。また適切に接  
Search by product, category, or phrase  
てください。  
Korea  
report problems to Axis support staff by logging in to  
your private support area  
이 기기는 업무용(A급) 전자파적합기기로서 판매  
자 또는 사용자는 이 점을 주의하시기 바라며, 가  
정외의 지역에서 사용하는 것을 목적으로 합니다.  
적절히 접지된 STP (shielded twisted pair) 케이블  
을 사용하여 제품을 연결 하십시오.  
chat with Axis support staff (selected countries only)  
visit Axis Support at www.axis.com/techsup/  
Learn More!  
Visit Axis learning center www.axis.com/academy/ for  
useful trainings, webinars, tutorials and guides.  
Safety  
This product complies with IEC/EN/UL 60950-1, Safety of  
Information Technology Equipment. If its connecting cables  
are routed outdoors, the product shall be grounded either  
through a shielded network cable (STP) or other appropriate  
method.  
The power supply used with this product shall fulfill  
the requirements for Safety Extra Low Voltage  
(SELV) and Limited Power Source (LPS) according to  
IEC/EN/UL 60950-1.  
Disposal and Recycling  
When this product has reached the end of its useful life,  
dispose of it according to local laws and regulations. For  
information about your nearest designated collection point,  
contact your local authority responsible for waste disposal.  
In accordance with local legislation, penalties may be  
applicable for incorrect disposal of this waste.  
Europe  
This symbol means that the product shall not be  
disposed of together with household or commercial waste.  
Directive 2012/19/EU on waste electrical and electronic  
equipment (WEEE) is applicable in the European Union  
member states. To prevent potential harm to human health  
and the environment, the product must be disposed of in  
an approved and environmentally safe recycling process.  
For information about your nearest designated collection  
point, contact your local authority responsible for waste  
disposal. Businesses should contact the product supplier for  
information about how to dispose of this product correctly.  
This product complies with the requirements of  
Directive 2011/65/EU on the restriction of the use of  
certain hazardous substances in electrical and electronic  
equipment (RoHS).  
China  
This product complies with the requirements of the  
legislative act Administration on the Control of Pollution  
Caused by Electronic Information Products (ACPEIP).  
Contact Information  
Axis Communications AB  
Emdalavägen 14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Download from Www.Somanuals.com. All Manuals Search And Download.  
AXIS Q604 Series  
Safety Information  
Read through this Installation Guide carefully before installing the product. Keep the Installation  
Guide for future reference.  
Hazard Levels  
DANGER  
WARNING  
CAUTION  
NOTICE  
Indicates a hazardous situation which, if not avoided, will result in  
death or serious injury.  
Indicates a hazardous situation which, if not avoided, could result  
in death or serious injury.  
Indicates a hazardous situation which, if not avoided, could result  
in minor or moderate injury.  
Indicates a situation which, if not avoided, could result in damage  
to property.  
Other Message Levels  
Important  
Indicates significant information which is essential for the product  
to function correctly.  
Note  
Indicates useful information which helps in getting the most out  
of the product.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
AXIS Q604 Series  
Safety Instructions  
WARNING  
• The Axis product shall be installed by a trained professional.  
NOTICE  
• The Axis product shall be used in compliance with local laws and regulations.  
• To use the Axis product outdoors, or in similar environments, it shall be installed in an  
approved outdoor housing.  
• Store the Axis product in a dry and ventilated environment.  
• Avoid exposing the Axis product to shocks or heavy pressure.  
• Do not install the product on unstable brackets, surfaces or walls.  
• Use only applicable tools when installing the Axis product. Excessive force could cause  
damage to the product.  
• Do not use chemicals, caustic agents, or aerosol cleaners. Use a clean cloth dampened  
with pure water for cleaning.  
• Use only accessories that comply with technical specification of the product. These can be  
provided by Axis or a third party.  
• Use only spare parts provided by or recommended by Axis.  
• Do not attempt to repair the product by yourself. Contact Axis support or your Axis  
reseller for service matters.  
Transportation  
NOTICE  
• When transporting the Axis product, use the original packaging or equivalent to prevent  
damage to the product.  
Battery  
The Axis product uses a 3.0 V BR/CR2032 lithium battery as the power supply for its internal  
real-time clock (RTC). Under normal conditions this battery will last for a minimum of five years.  
Low battery power affects the operation of the RTC, causing it to reset at every power-up. When  
the battery needs replacing, a log message will appear in the product’s server report. For more  
information about the server report, see the product´s setup pages or contact Axis support.  
The battery should not be replaced unless required, but if the battery does need replacing, contact  
Axis support at www.axis.com/techsup for assistance.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
AXIS Q604 Series  
WARNING  
• Risk of explosion if the battery is incorrectly replaced.  
• Replace only with an identical battery or a battery which is recommended by Axis.  
• Dispose of used batteries according to local regulations or the battery manufacturer's  
instructions.  
Dome Cover  
NOTICE  
• Be careful not to scratch, damage or leave fingerprints on the dome cover because this  
could decrease image quality. If possible, keep the protective plastic on the dome cover  
until the installation is complete.  
• Do not clean a dome cover that looks clean to the eye and never polish the surface.  
Excessive cleaning could damage the surface.  
• For general cleaning of the dome cover it is recommended to use a non-abrasive,  
solvent-free neutral soap or detergent mixed with pure water and a soft, clean cloth. Rinse  
well with pure lukewarm water. Dry with a soft, clean cloth to prevent water spotting.  
• Never use harsh detergents, gasoline, benzene or acetone etc. and avoid cleaning the  
dome cover in direct sunlight or at elevated temperatures.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
AXIS Q604 Series  
Installation Guide  
This Installation Guide provides instructions for installing AXIS Q6042/Q6044/Q6045 Mk II PTZ  
Dome Network Camera on your network. For other aspects of using the product, see the User  
Manual available at www.axis.com  
Installation Steps  
1. Make sure the package contents, tools and other materials necessary for the installation  
are in order. See page 9 .  
2. Study the hardware overview. See page 10.  
3. Study the specifications. See page 17.  
4. Install the hardware. See page 18.  
5. Access the product. See page 26.  
Package Contents  
AXIS Q6042/Q6044/Q6045 PTZ Dome Network Camera  
Clear transparent dome cover (premounted)  
Smoked transparent dome cover  
Mounting kit for hard ceilings and drop ceilings  
AXIS T8123 High PoE Midspan 1-port (LPS)  
Installation and Management Software CD  
Printed materials  
-
-
-
-
Installation Guide (this document)  
Drill template (2x)  
Extra serial number label (2x)  
AVHS Authentication key  
Optional Accessories  
AXIS T91A Mounting Accessories  
Multi-connector cable for connection of I/O, audio and power  
For information about available accessories, see www.axis.com  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
 
AXIS Q604 Series  
Hardware Overview  
1
2
3
4
5
6
7
8
9
10  
Unit holder (3x)  
Camera base lid  
Camera base lid screw T20 (3x)  
Hook for safety wire  
Part number (P/N) & Serial number (S/N)  
Cable track (2x)  
Foam gasket  
Network connector (PoE+)  
Multi-connector  
Top cover  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
 
AXIS Q604 Series  
Camera Unit  
1
2
3
4
SD card slot (SDHC)  
Status LED indicator  
Control button  
Power button  
Dome Cover  
1
2
3
4
5
Dome bracket screw T20 (4x)  
Dome bracket  
Dome cover  
Dome ring screw T20 (4x)  
Dome ring  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
AXIS Q604 Series  
Hard Ceiling Mount  
1
2
Mounting plate  
Safety wire  
Drop Ceiling Mount  
1
2
3
4
5
6
7
Mounting plate  
Mounting plate screw T20 (3x)  
Bracket arm  
Bracket arm screw T20 (3x) and washer (3x)  
Bracket ring  
Trim ring  
Safety wire  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
AXIS Q604 Series  
LED Indicators  
LED  
Color  
Indication  
Status  
Unlit  
Connection and normal operation  
Amber  
Amber/red  
Steady during startup. Flashes during firmware upgrade.  
Flashes amber/red if network connection is unavailable  
or lost.  
Red  
Flashes red for firmware upgrade failure.  
Green  
Shows steady green for 10 seconds for normal operation  
after restart.  
Midspan LED Indicators  
LED  
Color  
Indication  
Port  
Unlit  
No camera connected.  
Green  
Steady when camera connected, normal operation.  
Green, flashing  
Slow flash when overcurrent or short circuit condition  
on the port.  
Green, flashing  
Green  
Fast flash when input voltage is out of range or other  
internal error.  
AC  
Steady when AC power input connected.  
Connectors and Buttons  
For specifications and operating conditions, see page 17.  
Network Connector  
RJ45 Ethernet connector with Power over Ethernet Plus (PoE+).  
NOTICE  
Use the supplied midspan.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13  
 
AXIS Q604 Series  
NOTICE  
The product shall be connected using a shielded network cable (STP). All cables connecting  
the product to the network shall be intended for their specific use. Make sure that the  
network devices are installed in accordance with the manufacturer’s instructions. For  
information about regulatory requirements, see Electromagnetic Compatibility (EMC) on  
page 2 .  
I/O and Audio Connector  
Terminal connector for connecting external equipment:  
Audio equipment  
Input/Output (I/O) devices  
When connecting external equipment, a multi-connector cable (available from Axis) is required  
in order to maintain the product’s IP rating. For more information, see Multi-Connector Cable  
(sold separately) on page 15.  
SD Card Slot  
An SD card (not included) can be used for local recording with removable storage. For more  
information, see Specifications on page 17.  
NOTICE  
To prevent corruption of recordings, the SD card should be unmounted before removal. To  
unmount, go to Setup > System Options > Storage > SD Card and click Unmount.  
Note  
For SD card recommendations see www.axis.com  
Control Button  
The control button is used for:  
Resetting the product to factory default settings. See page 26.  
Connecting to an AXIS Video Hosting System service or AXIS Internet Dynamic DNS  
Service. For more information about these services, see the User Manual.  
Power Button  
Press and hold the power button to temporarily power the product when the dome cover is  
removed. The power button is also used with the control button to reset the camera to factory  
default settings. See page 26.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
AXIS Q604 Series  
Multi-Connector Cable (sold separately)  
When connecting external equipment to the Axis product, a multi-connector cable (available from  
Axis) is required in order to maintain the product’s IP rating. The multi-connector cable can be  
purchased from your Axis reseller.  
Connect the multi-connector cable to the product’s multi-connector. To locate the multi-connector,  
see Hardware Overview on page 10. The cable provides the following connectors:  
Power connector - 3-pin terminal block used for power input. See image below. Use a Safety Extra  
Low Voltage (SELV) compliant limited power source (LPS) with either a rated output power limited  
to 100 W or a rated output current limited to 5 A.  
Audio in (pink) - 3.5 mm input for a mono microphone, or a line-in mono signal (left channel is  
used from a stereo signal).  
Audio out (green) - 3.5 mm output for audio (line level) that can be connected to a public address  
(PA) system or an active speaker with a built-in amplifier. A stereo connector must be used for the  
audio out.  
I/O terminal connector - Use with external devices in combination with, for example, tampering  
alarms, motion detection, event triggering, time lapse recording and alarm notifications. In addition  
to the 0 V DC reference point and power (DC output), the I/O connector provides the interface to:  
Digital output — For connecting external devices such as relays and LEDs.  
Connected devices can be activated by the VAPIX® Application Programming  
Interface, output buttons on the Live View page or by an Action Rule. The output  
will show as active (shown under System Options > Port & Devices > Port  
Status) if the alarm device is activated.  
Digital input — An alarm input for connecting devices that can toggle between  
an open and closed circuit, for example: PIRs, door/window contacts, glass  
break detectors, etc. When a signal is received the state changes and the input  
becomes active (shown under System Options > Port & Devices > Port Status).  
Function  
0 V DC (-)  
DC output  
Pin  
Notes  
Specifications  
1
2
Can be used to power auxiliary equipment. 3.3 V DC  
Note: This pin can only be used as power Max load =  
out.  
250 mA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15  
 
AXIS Q604 Series  
3–6  
Configurable  
(Input or  
Output)  
Digital input – Connect to pin 1 to  
activate, or leave floating (unconnected)  
to deactivate.  
0 to max 40 V DC  
Digital output – Connected to pin 1 when 0 to max 40 V DC,  
activated, floating (unconnected) when  
deactivated. If used with an inductive  
load, e.g. a relay, a diode must be  
connected in parallel with the load, for  
protection against voltage transients.  
open drain,  
100 mA  
Connection diagram  
A
B
I/O configured as input  
I/O configured as output  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16  
AXIS Q604 Series  
DC power input  
AC power input  
I/O connector  
Specifications  
Operating Conditions  
The Axis product is intended for indoor use.  
Product  
Classification  
Temperature  
Humidity  
AXIS Q6042  
AXIS Q6044  
AXIS Q6045  
IEC 60721-4-3  
Class 3K3, 3M3  
IEC 60529 IP52  
0 °C to 50 °C  
(32 °F to 122 °F)  
10–85% RH (non-condensing)  
Power Consumption  
NOTICE  
Use a Safety Extra Low Voltage (SELV) compliant limited power source (LPS) with either  
a rated output power limited to 100 W or a rated output current limited to 5 A. Axis  
recommends using the supplied midspan.  
Product  
PoE+  
DC  
AC  
AXIS Q6042  
AXIS Q6044  
AXIS Q6045  
21.1 W 24–34 V DC, max. 17.4 W  
20.7 W 24–34 V DC, max. 17.9 W  
21.8 W 24–34 V DC, max. 17.8 W  
20–24 V AC, max. 24.7 VA  
20–24 V AC, max. 25.9 VA  
20–24 V AC, max. 26.0 VA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
17  
 
AXIS Q604 Series  
Connectors  
SD Card Slot  
Supports SD cards with up to 64 GB of storage. For best recording performance, use an SDHC  
or SDXC card with speed class 10.  
Install the Hardware  
NOTICE  
• The AXIS product shall be connected using a shielded network cable (STP). All cables  
connecting the product to the midspan shall be shielded (STP) and intended for their  
specific use. Make sure that the midspan is properly grounded. For information about  
regulatory requirements, see Regulatory Information on page 2 .  
• Mount the product with the dome cover facing downward.  
• Be careful not to scratch, damage or leave fingerprints on the dome cover because this  
could decrease image quality. If possible, keep the protective plastic on the dome cover  
until the installation is complete.  
The Axis product can be installed with the cables routed through or along the wall or ceiling.  
Read all the instructions before installing the product. Some installation steps would benefit from  
being completed together because they require removal of the dome cover.  
A hardware installation can include the following:  
The product is supplied with a clear dome cover (premounted). A smoked dome cover is  
available as an accessory. To replace the dome cover, see page 18.  
A standard or high capacity SD card (not included) can be used to store recordings locally  
in the product. To install an SD card, see page 19.  
To install the product using the hard ceiling mount, see page 19.  
To install the product using the drop ceiling mount, see page 20.  
To install the product using a compatible bracket from AXIS T91A Mounting Accessories  
(sold separately), see page 23.  
To install the supplied midspan, see page 25.  
Replace the Dome Cover  
Replacing the dome cover is only necessary if you want to use the smoked dome cover or if the  
dome cover is scratched or damaged. Spare dome covers can be purchased from your Axis reseller  
1. Loosen the dome ring screws and remove the dome cover.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
18  
   
AXIS Q604 Series  
2. Remove the dome bracket screws and remove the dome bracket and the dome cover  
from the dome ring.  
3. Attach the dome bracket and the dome cover to the dome ring and tighten the screws  
(torque 1.2 Nm).  
4. To install an SD card (not included), see Install an SD Card on page 19.  
5. Attach the dome cover to the top cover and tighten the screws (torque 1.5 Nm).  
Install an SD Card  
It is optional to install a standard or high capacity SD card (not included), which can be used for  
local recording with removable storage.  
1. Loosen the dome ring screws and remove the dome cover.  
2. Insert an SD card (not included) into the SD card slot.  
3. Attach the dome cover to the top cover and tighten the screws (torque 1.5 Nm).  
NOTICE  
To prevent corruption of recordings, the SD card should be unmounted before it is ejected.  
To unmount, go to Setup > System Options > Storage > SD Card and click Unmount.  
Hard Ceiling Mount  
1. Prepare the ceiling for installation of the mounting plate. The supplied drill template  
can be used to position the holes. Make sure to use drill bits, screws and plugs that  
are appropriate for the material.  
2. Install the mounting plate. The arrow on the mounting plate will align with the logotype  
on the camera.  
1
2
Mounting plate  
Safety wire  
3. Loosen the camera base lid screws and remove the camera base lid.  
4. Secure the camera using the supplied safety wire.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
19  
   
AXIS Q604 Series  
5. Route and connect the network cable and the multi-connector cable (sold separately), if  
applicable, to the camera.  
NOTICE  
• Be careful not to damage the cables when connecting them.  
• Make sure that the foam gasket holes are aligned with the cable tracks and, if applicable,  
remove the cut-out piece for the multi-connector cable from the foam gasket.  
1
2
3
Cable holders  
Multi-connector cable (sold separately)  
Network cable (not included)  
6. Turn the cable holders to keep the cables in place.  
7. Put the camera base lid back in its original position and tighten the screws (torque  
1.5 Nm).  
8. Slide the unit holders on the network camera into the slots in the mounting plate and  
rotate the camera unit.  
9. Install the supplied midspan. See page 25.  
Drop Ceiling Mount  
WARNING  
The combined weight of the camera and ceiling mount is approximately 3200 g (7.1 lb.).  
Make sure that the ceiling material is strong enough to support this weight.  
NOTICE  
The ceiling tile should be 5–60 mm (0.2–2.4 in.) thick.  
1. Remove the ceiling tile in which the drop ceiling mount is to be fitted.  
2. Cut a hole in the ceiling tile for the drop ceiling mount. Use the supplied template to  
mark the position and cut around the template.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
20  
 
AXIS Q604 Series  
1
2
Ceiling tile  
Hole diameter 225 mm (8.9 in.)  
3. Assemble the ceiling bracket and attach it to the ceiling tile. Make sure the arrows on  
the mounting plate and the ceiling bracket are pointing in the same direction for the  
logotypes on the camera and the trim ring to align.  
4. Tighten the bracket arm screws.  
5. Loosen the camera base lid screws and remove the camera base lid.  
6. Route and connect the network cable and the multi-connector cable (sold separately), if  
applicable, to the camera.  
NOTICE  
• Be careful not to damage the cables when connecting them.  
• Make sure that the foam gasket holes are aligned with the cable tracks and, if applicable,  
remove the cut-out piece for the multi-connector cable from the foam gasket.  
1
2
3
Cable holders  
Multi-connector cable (sold separately)  
Network cable (not included)  
7. Turn the cable holders to keep the cables in place.  
8. Put the camera base lid back in its original position and tighten the screws (torque  
1.5 Nm).  
9. Secure the camera using the supplied safety wire.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
21  
AXIS Q604 Series  
1
2
3
4
5
Mounting plate  
Ceiling bracket  
Ceiling tile  
Safety wire  
Hook for safety wire  
10. Slide the unit holders on the network camera into the slots in the mounting plate and  
rotate the camera unit.  
11. Install the supplied midspan. See page 25.  
12. Install the ceiling tile with the camera mounted on it.  
13. Put the trim ring on the ceiling bracket and tighten the screws.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
22  
AXIS Q604 Series  
1
2
Trim ring  
Trim ring screw T20 (4x)  
Bracket Mount (sold separately)  
1. Install the selected bracket according to the instructions supplied with the bracket. If  
drilling is required, make sure to use drill bits, screws and plugs that are appropriate for  
the material.  
2. Loosen the camera base lid screws and remove the camera base lid.  
3. Route the network cable and the multi-connector cable, if applicable, through the holes  
in the mounting bracket.  
4. Secure the camera using the supplied safety wire.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
23  
 
AXIS Q604 Series  
1
2
3
4
Screw T30 (3x)  
Slot for unit holder (3x)  
Safety wire  
Wall bracket (mounting example)  
5. Connect the network cable and the multi-connector cable (sold separately), if applicable,  
to the camera.  
NOTICE  
• Be careful not to damage the cables when connecting them.  
• Make sure that the foam gasket holes are aligned with the cable tracks and, if applicable,  
remove the cut-out piece for the multi-connector cable from the foam gasket.  
1
2
3
Cable holders  
Multi-connector cable (sold separately)  
Network cable (not included)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
24  
AXIS Q604 Series  
6. Turn the cable holders to keep the cables in place.  
7. Put the camera base lid back in its original position and tighten the screws (torque  
1.5 Nm).  
8. Slide the unit holders on the network camera into the slots in the mounting bracket and  
rotate the camera unit.  
9. Secure the network camera to the mounting bracket by tightening the screws.  
10. Install the supplied midspan. See page 25.  
Install the Midspan  
The supplied midspan enables Axis network video products with high power consumption to receive  
data and power over the same network cable.  
1. Connect the midspan (data in) to the network switch using a network cable.  
2. Connect the midspan (data and power out) to the camera using the network cable that  
has been connected to the camera.  
3. Connect the midspan to a grounded (earthed) mains power outlet (100–240 V AC) using  
the supplied power cable.  
1
2
3
4
Data and power out (connect to Axis product)  
Data in (connect to network)  
AC input LED indicator  
Port LED indicator  
4. Make sure that the LEDs on the midspan indicate the correct conditions. See Midspan  
LED Indicators on page 13.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
25  
 
AXIS Q604 Series  
Access the Product  
Use the tools provided on the Installation and Management Software CD to assign an IP address,  
set the password and access the video stream. This information is also available from the support  
Reset to Factory Default Settings  
Important  
Reset to factory default should be used with caution. A reset to factory default will reset  
all settings, including the IP address, to the factory default values.  
Note  
The installation and management software tools are available on the CD supplied with the  
product and from the support pages on www.axis.com/techsup  
To reset the product to the factory default settings:  
1. Press and hold the control button and the power button for about 15–30 seconds until  
the status LED indicator flashes amber. See Hardware Overview on page 10.  
2. Release the control button but continue to hold down the power button until the status  
LED indicator turns green.  
3. Release the power button and assemble the product.  
4. The process is now complete. The product has been reset to the factory default settings.  
If no DHCP server is available on the network, the default IP address is 192.168.0.90  
5. Using the installation and management software tools, assign an IP address, set the  
password and access the video stream.  
It is also possible to reset parameters to factory default via the web interface. Go to Setup  
> System Options > Maintenance.  
Further Information  
The User Manual is available at www.axis.com  
Visit www.axis.com/techsup to check if there is updated firmware available for your network  
product. To see the currently installed firmware version, go to Setup > About.  
Visit Axis learning center www.axis.com/academy for useful trainings, webinars, tutorials and  
guides.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
26  
   
AXIS Q604 Series  
Warranty Information  
For information about Axis’ product warranty and thereto related information, see  
Download from Www.Somanuals.com. All Manuals Search And Download.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Errata  
Valid for AXIS Q60 Series  
About this document  
This document is a correction of AXIS Q60 Series Installation Guide AXIS Q6042/Q6044/Q6045.  
page 2  
Regulatory Information  
USA  
This equipment has been tested using an unshielded network cable (UTP) and  
found to comply with the limits for a Class A digital device, pursuant to part  
15 of the FCC rules. This equipment has also been tested using a shielded  
network cable (STP) and found to comply with the limits for a Class A digital  
device, pursuant to part 15 of the FCC rules. These limits are designed to  
provide reasonable protection against harmful interference when the  
equipment is operated in a commercial environment. This equipment  
generates, uses, and can radiate radio frequency energy and, if not installed  
and used in accordance with the instruction manual, may cause harmful  
interference to radio communications. Operation of this equipment in a  
residential area is likely to cause harmful interference in which case the user  
will be required to correct the interference at his own expense.  
page 14  
Network Connector  
Due to local regulations or the environmental and electrical conditions in which  
the product is to be used, a shielded network cable (STP) may be appropriate or  
required. All cables connecting the product to the network and that are routed  
outdoors or in demanding electrical environments shall be intended for their  
specific use. Make sure that the network devices are installed in accordance  
with the manufacturer’s instructions. For information about regulatory  
requirements, see Regulatory Information.  
page 18  
Install the Hardware  
Due to local regulations or the environmental and electrical conditions in which  
the product is to be used, a shielded network cable (STP) may be appropriate or  
required. All cables connecting the product to the network and that are routed  
outdoors or in demanding electrical environments shall be intended for their  
specific use. Make sure that the network devices are installed in accordance  
with the manufacturer’s instructions. For information about  
regulatory requirements, see Regulatory Information.  
Errata, Installation Guide  
AXIS Q60 Series  
Date: October 2014  
Part No: 60286  
© Axis Communications AB,  
2014  
Part No (original document):  
59146  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Guide  
AXIS Q604 Series  
© Axis Communications AB, 2014  
Ver. M2.8  
Date: August 2014  
Part No. 59146  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Acer Cell Phone E100 User Manual
Adesso Scanner EZSCAN 2000 User Manual
AEG Microwave Oven MC2660E User Manual
AEG Power Supply 3M 2 User Manual
Allied Telesis Switch AT 8000S 24 User Manual
Alpine Car Stereo System ERA G311 User Manual
American Dryer Corp Clothes Dryer AD 235D User Manual
Avet Reels Fishing Equipment LX 46 User Manual
Avocent Network Card CCM4850 User Manual
Beko Hair Dryer DPU 7360 GX User Manual