Preface
Thank you for purchasing the AXIS 540/640 Network Print Server. Our goal in developing this
product is to enable you to connect your printers anywhere in your network, allowing all network
users access to shared printer resources.
About Axis
Axis Communications, founded in 1984, is one of the world’s fastest growing companies in the
market of network connectivity. The headquarters are located in Lund, Sweden, with subsidiaries
in Beijing, Boston, Hong Kong, Paris, Sao Paulo, Shanghai, Singapore and Tokyo.
Axis Communications has a distributor network operating in more than 60 countries world-wide,
marketing four major product lines:
Network CD-ROM Servers. Multi-protocol CD-ROM servers provide a flexible and
cost-efficient solution for sharing CD-ROMs across the network. The AXIS StorPoint CD, the
stand-alone version, and the AXIS StorPoint CD/T, the plug-in CD-ROM tower module, are
both available in Ethernet and Token Ring versions.
Network Print Servers. These intelligent Ethernet and Token Ring print servers support a
wide range of LAN protocols. The AXIS 150, 152, 540, 542, 560, 570 are Ethernet print servers,
while the AXIS 640, 642, 660, 670 are Token Ring print servers.
Network Camera Servers. The AXIS NetEye 200 Network Camera attaches directly to an
Ethernet network and supports TCP/IP and Internet-related protocols, acting as a Web server.
IBM Mainframe and S/3x – AS/400 Printer Interfaces. These products include a wide
range of plug-in interfaces and stand-alone products such as the AXIS Cobra+, AXIS 330/370 Co-
bra, AXIS HP MIO, the AXIS AFP IPDS-to-PostScript converter and the AXIS AFP MIO/IOP
IPDS-to-PCL converters.
About this manual
This manual will guide you through simple step-by-step installation and set up procedures.
Introduction - The AXIS 540/640 Print Server, how it works, where to use it, its main features.
Basic Installation - How to connect your AXIS 540/640 to your printer and network.
Setting Up... - Five sections; one for each of the network environments for your AXIS 540/640.
AXIS 540/640 User’s Manual
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Table of Contents
Section 1
Section 2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Where to use it . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Basic Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Checking and Identifying the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Connecting Printers to the AXIS 540/640 . . . . . . . . . . . . . . . . . . . . . . . . . 17
Connecting the AXIS 540/542 to the Ethernet Network . . . . . . . . . . . . 18
Connecting the AXIS 640/642 to the Token Ring Network . . . . . . . . . 19
Basic Set Up of the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Basic Set Up with AXIS NetPilot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Basic Set Up for TCP/IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Section 3
Section 4
Setting Up - NetWare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Set Up using the AXIS NetPilot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Other NetWare Configuration Methods . . . . . . . . . . . . . . . . . . . . . . . . . 42
Setting Up - Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Installation Using AXIS Print Utility for Windows . . . . . . . . . . . . . . . . . . . 45
Windows 3.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Windows for Workgroups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Windows 95 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Windows NT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Windows NT - LPD Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Other Windows Configuration Methods . . . . . . . . . . . . . . . . . . . . . . . . . 56
Section 5
Section 6
Setting Up - OS/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Installation Using AXIS Print Utility for OS/2 . . . . . . . . . . . . . . . . . . . . . . 57
Integrating your AXIS 540/640 into the OS/2 Environment . . . . . . . . . . 59
Other OS/2 Configuration Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Setting Up - Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Installation Using the Chooser Window . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Choosing a Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Other Macintosh Configuration Methods . . . . . . . . . . . . . . . . . . . . . . . . . 68
AXIS 540/640 User’s Manual
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Section 7
Section 8
Setting Up - UNIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Installation in the UNIX Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Print Methods on TCP/IP Networks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Using Telnet with the AXIS 540/640 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Using SNMP for Remote Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Other UNIX Configuration Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Web Based Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Accessing the Web Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Enhanced HTTP Management Services . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Appendix A The Test Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Appendix B The Parameter List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Editing the Configuration Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
The Config File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Appendix C Updating the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Obtaining the Updated Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Upgrading the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Appendix D Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Appendix E How To Contact Axis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
4
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Introduction
Section 1 Introduction
The AXIS 540/640 series is a range of plug-in network print servers
for use in Ethernet and Token Ring environments. The AXIS
540/640 server plugs directly into the printer’s parallel port and
provides all network users with access to shared printer resources.
Using state of the art technology the server provides excellent print
flexibility and simultaneously supports multiple network protocols.
This includes advanced support for TCP/IP, support for NetWare
including NDS, and support for over 20 UNIX systems, Windows for
Workgroups, Windows 95, Windows NT, and OS/2. The AXIS
540/640 range also includes AXIS 540+ and 542+ models which
support Apple EtherTalk in addition to the above protocols.
Network The AXIS 540/542 and AXIS 640/642 print servers have identical
Connections functionality, but are designed for use in different network
environments, or with different types of network cabling.
The AXIS 540/540+ and AXIS 542/542+ are suitable for Ethernet
network environments. The AXIS 540/540+ have network connectors
for twisted pair (10 base T) cabling, while the AXIS 542/542+ have
network connectors for thin wire (10 base2) cabling.
The AXIS 540 Network Print Server
AXIS 540/640 User’s Manual
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Introduction
The AXIS 640/642 models are suitable for Token Ring network
environments. The AXIS 640 has a network connector for Unshielded
Twisted Pair (UTP) cabling, while the AXIS 642 has a network
connector for Shielded Twisted Pair (STP) cabling.
How it Works
Because of the variety of computer and operating systems employed in
a modern computing environment, it is common for print data to be
transmitted across a single network using a variety of transport
protocols. The AXIS 540/640 Print Server automatically detects the
protocol being used for each print job, and adapts the print data into a
format which is suitable for the printer.
As the AXIS 540/640 is a pocket-sized print server which plugs
directly in to the printer’s parallel port, there is no need for additional
cabling.
Installation of the AXIS 540/640 and its integration into the network
is performed using one of the Axis software packages; AXIS Print
Utility for Windows, AXIS Print Utility for OS/2, axinstall for UNIX
environments, and AXIS NetPilot.
If you are using the TCP/IP network transport protocol and have
access to an Internet browser, you may also access AXIS540/640 series
of Network Print Servers from any standard Web browser, regardless
of your type of platform. Furthermore, the enhanced HTTP support
available in the AXIS 540+/542+ and Token Ring models includes a
quick and easy management tool that allows you to configure and view
unit status, within all supported networking environments.
6
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Introduction
The AXIS NetPilot software, which is supplied on the AXIS Utilities
diskette, makes the job of installation and configuration quick and
convenient. AXIS NetPilot runs on Windows platforms, and provides
a quick installation facility so that the AXIS 540/640 can be rapidly
put to use. Together with the supplied AXIS Utilities, it provides user
friendly facilities to tune the configuration, allowing you to maintain
optimum printing performance as you make changes to the network.
For more detailed information that is not included in this manual, you
are invited to visit our WWW Home Page where you can down-load
further technical information. You may also down-load on-line
manuals, tools such as theAcrobat Reader and the latest versionsof the
software utilities. Naturally enough links to this information are
provided from within the AXIS 540/640 home pages. Your Axis dealer
will also be pleased to provide you with additional information or
assistance that you might require. For details on the appropriate
WWW addresses in your region, please refer to Appendix E - How To
Contact Axis.
AXIS 540/640 User’s Manual
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Introduction
Where to use it
The AXIS 540/640 can communicate with all the major computer
systems and network protocols. The supported protocols can be
handled simultaneously making the AXIS 540/640 the ideal print
server solution for a mixed systems environment.
Web Browser Because the AXIS 540/640 comprises its own built-in Web server it
may be configured and managed directly from its own Web pages,
using HTTP over a TCP/IP network. Access to the AXIS 540/640 via
HTTP, affords the user with a platform-independent management
tool that is suitable for all of the supported network environments.
NetWare AXIS NetPilot is the preferred utility for installing and integrating the
Environment AXIS 540/640 into a NetWare environment. The AXIS 540/640 can
be operated in both Print Server Mode and Remote Printer Mode.
It is compatible with both NetWare 4.10 and above (NDS and
bindery emulation), as well as NetWare 3.11, 3.12.
8
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Introduction
In Print Server Mode the AXIS 540/640 emulates a NetWare print
server, while in Remote Printer Mode it emulates a workstation
running RPRINTER or NPRINTER. Logical printers are supported
in both bindery and NDS modes for both PSERVER and
NPRINTER.
Windows Unless you wish to change the default name of your AXIS 540/640
Environments the setup operation within the windows environment may be
performed solely with the AXIS Print Utility for Windows, which is
supplied on the AXIS Utilities diskette.
Having installed the AXIS 540/640 onto your network, the AXIS
Print Utility for Windows may then be used to install and maintain
the print server ports as Windows printer ports. Windows 3.1,
Windows for Workgroups, Windows 95, and Windows NT are all
supported.
OS/2 Environments Unless you wish to change the default name of your AXIS 540/640
the setup operation in an OS2 environment may be performed solely
with the supplied AXIS Print Utility for OS2.
Use the AXIS Print Utility for OS/2 to install and integrate the AXIS
540/640 into the OS/2 spool system. The printers attached to the
AXIS 540/640 will appear as connected directly to the file server, and
may be used by any client on your network.
UNIX Environment You can use the AXIS 540/640 as an integral part of your system, so
that the printers appear directly connected to the host print spool. Use
axinstall for the integration. You can also operate the AXIS 540/640 in
an interactive mode to print your host documents.
Several protocols and print methods are provided, the choice of which
is governed by your requirements and the system you are using. Five
print methods are supported in UNIX: LPD, FTP, PROS A,
PROS B, and Reverse Telnet.
The AXIS 540/640 supports any host that uses the TCP/IP protocol
suite.
AXIS 540/640 User’s Manual
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Introduction
Macintosh The printer connected to the AXIS 540+/542+ will appear as a
Environment (AXIS LaserWriter printer connected to an AppleTalk network. Once
540+/542+ only) selected from the Chooser window in the Apple menu, the printers
can be accessed in the same manner as any other LaserWriter.
Main Features
Reliability The AXIS 540/640 hardware provides high performance and
reliability combined with low power consumption. The electronic
circuits are based on the proven AXIS ETRAX chip that comprises an
integrated 32 bit RISC processor and associated network controllers.
Flexibility It supports NetWare, Windows 95, Windows NT, Windows for
Workgroups, OS/2, Macintosh, and UNIX simultaneously, and five
different print methods in the TCP/IP environment.
Speed The AXIS ETRAX chip has been specifically designed for LAN
products and benefits users with a significantly faster throughput than
a direct PC-to-printer connection. The AXIS 540/640 has a sustained
data throughput of up to 390 kbytes per second. It also supports high
speed Centronics communication such as Hewlett-Packard Fast
Mode, High Speed and IBM Fast Byte is supported.
Easy to Install Without being a computer expert you caninstall the AXIS 540/640 in
minutes, allowing you to quickly realise the benefits afforded by
workgroup printing. The AXIS NetPilot installation software includes
a user friendly installation wizard. Together with the axinstall script
for UNIX workstations this allows installation into all of the AXIS
540/640 networking environments.
For TCP/IP networks your favourite Web browser may also act as a
convenient configuration tool. Links provided within the AXIS
540/640 Web pages allow modification of the configuration
parameters and quick access to useful information.
10
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Introduction
Security You may set up passwords for all users, restricting both log in and
printer access.
Monitoring The AXIS NetPilot software provided allows you to continuously
monitor printer status. The AXIS 540/640 also supports SNMP for
remote monitoring.
Futureproof The AXIS 540/640 has the ability to have its Flash memory updated.
This allows you to quickly update and enhance the operational
features of your AXIS 540/640 when new print server software
becomes available. All software updates are free of charge. You may
perform the update operation over the network which makes the job
of updating your AXIS 540/640 quick and easy.
Pocket-sized One high-speed parallel port that plugs directly into the printer´s
parallel port. No cables needed. Bi-directional support for Apple
EtherTalk.
AXIS 540/640 User’s Manual
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Introduction
12
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Basic Installation
Section 2 Basic Installation
Checking and Identifying the Hardware
Unpack and check all the items using the following check list. Contact
your dealer if anything is missing or damaged. All packing materials
are recyclable.
The AXIS 540/640 Hardware Pack contains:
AXIS 540, part no: 0058-1, or AXIS 542, part no: 0058-2, or
AXIS 540+, part no: 0058-3, or AXIS 542+, part no: 0058-4, or
AXIS 640, part no: 0059-1, or AXIS 642, part no: 0059-2
AXIS 540/640 User’s Manual, part no: 14677
AXIS 540/640 User’s Printing Guide, part no: 14678
AXIS 540/640 Quick Installation Guide, part no: 14679
Product Brochure, part no: 14412
AXIS UserGroup Registration Card, part no: 15119
3.5” AXIS Utilities disk comprising the AXIS NetPilot
Configuration Software and AXIS Print Utility for Windows,
part no: 14428
3.5” OS/2 Utilities disk with AXIS Print Utility for OS/2, part
no: 14232
Power Supply:
AXIS
540/540+
(PS-A)
AXIS
542/542+/640/642
(PS-B)
Part no.
Europe
UK
13599
12866
12867
12919
13249
13267
13268
13269
13270
13936
Australia
USA
Japan
AXIS 540/640 User’s Manual
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Basic Installation
Optional accessories
Self-adhesive velcro ribbons, part no: 13282 and 13283
BNC T-adaptor (AXIS 542 only), part no: 12839
Printer cable extension, part no: 13522
14
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Basic Installation
AXIS 540/542 Connectors
LPT1 Printer
Connector
Ethernet
10base2
Connector
Ethernet
10baseT
Connector
or
Test Button
Network Indicator
Power Indicator
External Power
Supply Connector
Plan view of the AXIS 540/542
Test Button The test button is used for:
•
•
•
Printing a test page to check the connection to the printer.
Printing the parameter list showing all the AXIS 540/542 settings.
Resetting the AXIS 540/542 parameters to the factory default
settings.
Refer to Appendix A - The Test Button for more information about
printing and resetting the parameters.
Network Indicator This flashes to indicate network activity.
Power Indicator Is normally on while power is applied. If it is not lit, or it flashes, there
is a problem with the AXIS 540/542 or its power supply.
AXIS 540/640 User’s Manual
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Basic Installation
AXIS 640/642 Connectors
LPT1 Printer
Connector
Ring Speed
Switch
(recessed)
Token Ring
STP
Connector
Token Ring
UTP
Connector
or
Test Button
Network Indicator
Power Indicator
External Power
Supply Connector
Plan view of the AXIS 640/642
Test Button The test button is used for:
•
•
•
Printing a test page to check the connection to the printer.
Printing the parameter list showing all the AXIS 640/642 settings.
Resetting the AXIS 640/642 parameters to the factory default
settings.
Refer to Appendix A - The Test Button for more information about
printing and resetting the parameters.
Ring Speed Switch This switch is set to match your network speed.
Network Indicator This flashes to indicate network activity.
Power Indicator Is normally on while power is applied. If it is not lit, or it flashes, there
is a problem with the AXIS 640/642 or its power supply.
16
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Basic Installation
Connecting Printers to the AXIS 540/640
Caution
Make sure that the external power supply is marked with the correct
mains voltage.
Connect a Printer: 1. Switch off the printer.
2. Connect the AXIS 540/640 to the printer, either directly to the
parallel printer port, or using the optional velcro ribbons and
printer cable extension.
3. Connect the external power supply to the AXIS 540/640. The
indicators will flash during power up and self test. When the
Network indicator stops flashing and remains off, the AXIS
540/640 is ready for use.
Test the Connection: 1. Switch on the printer.
2. Press and release the test button on the AXIS 540/640 to print a
test page.
The test page shows the most important parameters as well as the
firmware version number. But all you need to be concerned with at
this stage is whether the test page has printed satisfactorily or not.
Note: ❏ The AXIS 540/640 supports high speed Centronics
Communication. For use with older printers not supporting high
speed, this function may be disabled by changing the parameter
L1_CENTR as defined in Appendix A - The Test Button.
AXIS 540/640 User’s Manual
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Basic Installation
Connecting the AXIS 540/542 to the Ethernet Network
1. Switch off the printer and disconnect the AXIS 540/542 external
power supply.
2. Note the AXIS 540/542 serial number found on the underside
label of the print server. You need this number during the
network configuration.
3. Connect your AXIS 540/542 to the network using a twisted pair
(10baseT) or thin wire (10base2) cable.
the AXIS 540/542.
5. Successful connection of the AXIS 540/542 to your network will
be confirmed by the intermittent flashing of the Network
Indicator.
6. You are now ready to install your server onto your network using
one of the methods detailed in the Installation Guide, on page 20.
By commencing with the preferred installation method, you can
further verify that your AXIS 540/542 is properly connected to
your network.
Note: ❏ Each AXIS 540/542 Print Server is pre-configured with a unique
Node Address that is identical to the serial number. This can be
changed using the AXIS NetPilot, or any standard Web browser,
if required.
18
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Basic Installation
Connecting the AXIS 640/642 to the Token Ring Network
Caution
DO NOT connect or disconnect the network cabling while the
AXIS 640/642 is powered on.
1. Switch off the printer and disconnect the AXIS 640/642 external
power supply.
2. Note the AXIS 640/642 serial number found on the underside
label of the print server. You need this number during the
network configuration.
3. Slide the Ring Speed switch towards 4 or 16 depending on the
ring speed of your network.
4. Connect your AXIS 640/642 to the network using an STP
(Media Type 1) or UTP (Media Type 3) cable.
the AXIS 640/642.
6. Successful connection of the AXIS 640/642 to your network will
be confirmed by the intermittent flashing of the Network
Indicator.
7. You are now ready to install your server onto your network using
one of the methods detailed in the Installation Guide, on page 20.
By commencing with your preferred installation method, you can
further verify that your AXIS 640/642 is properly connected to
your network.
Notes: ❏ Each AXIS 640/642 Print Server is pre-configured with a unique
Node Address that is identical to the serial number. This can be
changed using the AXIS NetPilot, or any standard Web browser,
if so required.
❏ It is recommended that you use screened or foiled Media Type 3
cabling for 16 Mbit networks and not standard UTP cabling.
AXIS 540/640 User’s Manual
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Basic Installation
Basic Set Up of the Network
Installation Guide After connecting the AXIS 540/640 to your network you are now
ready to perform the basic setup procedures. The method of
installation that you choose should be dictated by your printing
requirement and the type of network into which you are integrating.
Proceed with an appropriate installation method from the list below:
NetWare
•
If you have access to a Windows platform which uses NetWare
you should firstly follow the procedures defined in:
- Basic Set Up with AXIS NetPilot, on page 22.
- Section 3 Setting Up - NetWare
UNIX
•
•
Perform the basic TCP/IP set up procedures if your network uses
UNIX workstations, as defined in:
- Basic Set Up for TCP/IP, on page 25.
- Section 7 Setting Up - UNIX
Windows
If this is unnecessary, proceed directly to:
- Section 4 Setting Up - Windows
If your Windows platform uses neither NetWare nor NetBEUI,
you must initially perform the basic TCP/IP set up procedures, as
defined in:
- Basic Set Up for TCP/IP, on page 25.
- Windows NT LPD Printing, Section 4
OS/2
•
•
If your network uses OS/2 workstations, use the NetPilot only if
you want to change the default print server name. If this is
unnecessary, proceed directly to:
- Section 5 Setting Up - OS/2
Macintosh
If the only workstations on your network are Apple computers,
you should refer directly to:
- Section 6 Setting Up - Macintosh
20
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Basic Installation
Web Based If you are using the TCP/IP protocol suite and also have access to an
Management Internet browser, you may manage the AXIS 540+, 542+ 640 and 642
models using HTTP, regardless of your system platform. Should you
wish to use this easy-to-use configuration method, you should initially
refer to:
•
Basic Set Up for TCP/IP, on page 25. Refer then to:
•
Section 8 Web Based Management
Installation Summary The appropriate Installation, Management and Configuration tools
for the AXIS 540/640 can be summarized in the following table:
Operating System
Protocols
Configuration/
Management
Installation
AXIS NetPilot
AXINSTALL
IPX/SPX
AXIS NetPilot
FTP, SNMP,
Web browser
TCP/IP (UNIX)
Use LPD
Monitor/Spooler*
FTP, SNMP,
Web browser
TCP/IP (Windows)
NetBIOS/NetBEUI
(Windows)
AXIS NetPilot
AXIS NetPilot
(**)
AXIS Print Utility for Windows
NetBIOS/NetBEUI
(OS/2)
AXIS Print Utility for OS/2
Standard using the Chooser
Apple EtherTalk
Recommended Installation, Configuration and Management tools
*
You may use the resident LPD monitor in Windows NT to print
via TCP/IP. A shareware LPR spooler is available for Windows
95, or Windows forWorkgroups. You can download this software
from http://www.axis.com/techsup/.
** Use Mac-FTP or HTTP. Alternatively use the AXIS NetPilot
from a PC platform within the same network.
AXIS 540/640 User’s Manual
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Basic Installation
Notes: ❏ IPX/SPX: used in Novell NetWare
❏ TCP/IP: used in UNIX systems,Windows NT, Windows 95,
Windows 3.11, Windows for Workgroups...
❏ NetBIOS/NetBEUI: used in Windows NT, Windows for
Workgroups, Windows 95, LAN Server, LAN Manager
Basic Set Up with AXIS NetPilot
Follow the instructions on the AXIS Utilities disk label to install the
AXIS NetPilot software on to your computer. AXIS NetPilot runs on
any of the Windows platforms: Windows 3.x, Windows 95, Windows
NT, Windows for Workgroups, or in a WinOS/2 window under
OS/2.
When AXIS NetPilot is started, the program searches the network for
new Axis units that have not yet been installed. If any new units are
found the user is given the option of installing them.
The AXIS Installation Wizard Main window
22
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Basic Installation
The user is guided through the installation process by a Wizard which
asks for the relevant information concerning your network
environment. You will find more information about AXIS NetPilot in
Section 3 Setting Up - NetWare.
Environments When configuring the AXIS 540/640 for use on your network you
may select any combination of the supported environments. In a
multi-platform environment you may wish to enable printing from all
of the supported environments: Netware, TCP/IP, Windows OS/2 or
AppleTalk.
NetWare NDS You may place NetWare Print Queues on a specific bindery server, or
alternatively into a NDS Tree.
Print Queues The default Print Queue names comprise of the print server name
followed by the Port name:
Environment
NetWare
Default name
AXIS1A0003_LPT1_Q
AX1A0003.LP1
Windows & OS/2
AppleTalk
AXIS1A0003_LPT1
Example of default Print Queue Names for each of the operating environments
The Installation Wizard allows you to amend the default names if you
wish.
The Internet Address During the Installation Wizard you may choose the method the AXIS
540/640 employs for obtaining an Internet Address. ARP, RARP,
BOOTP and DHCP are all supported. Refer to page 27, for more
information on these methods.
Wizard
A special form of user assistance that automates a task (in
this case the installation) through a dialog with the user.
Wizards help the user to accomplish tasks that are complex
and require experience, and even for the experienced user
can help to speed up an operation.
AXIS 540/640 User’s Manual
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Basic Installation
Test Page The final user prompt in the Installation Wizard allows you to print a
test page through NetWare. This page displays the name of all the
NetWare servers the AXIS 540/640 is connected to and shows the
status of each connection. This will assist diagnosis in the event of a
configuration error.
Notes: ❏ The parameters entered during installation are not permanent;
they can be altered at any time according to your network
printing requirements.
❏ No serious or permanent damage will be caused if you make a
mistake during installation. If at anytime you find that printing is
not satisfactory, the parameters can easily be changed to tune the
system to your requirements.
❏ For information on advanced functions, please refer to the AXIS
Network Print Server Technical Reference. You may down-load
this or other technical information over the Internet by accessing
the Axis WWW Home Page at http://www.axis.com/. Refer also
to Appendix E - How To Contact Axis.
Refer to one or more of the following sections to learn how you might
fine tune the AXIS 540/640 configuration and manage your network
printing. Proceed as is appropriate to your type of network.
Section 3 Setting Up - NetWare
Section 4 Setting Up - Windows
Section 5 Setting Up - OS/2
Section 6 Setting Up - Macintosh
Section 7 Setting Up - UNIX
Section 8 Web Based Management
24
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Basic Installation
Basic Set Up for TCP/IP
To establish communication with the TCP/IP network, an Internet
address and a host name must be mapped to the Ethernet/Node
address of your AXIS 540/640 Print Server. To do this, you must
firstly acquire an unused Internet address and decide upon an
appropriate and unique name for your AXIS 540/640. This
information then must then be included into your system host table.
The procedures for doing this are described below.
Before you start
System privileges You will need root privileges on your UNIX system, or administrator
privileges on a Windows NT server.
Ethernet address You will need to know the Ethernet address of your AXIS 540/542 to
perform the installation. The Ethernet address is based upon the serial
number of your AXIS 540/542. This means that an AXIS 540/542
with a serial number of 00408C100086, will have a corresponding
Ethernet address of 00 40 8C 10 00 86. The serial number of your
unit is located on the underside label of the unit.
Node address In Token Ring networks the node address is either the serial number
found on the underside label of the AXIS 640/642 or a Locally
Administrated Address.
AXIS 540/640 User’s Manual
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Basic Installation
The Internet Address Enter the Internet address and Host name into your host table using
and Host Name in the following step-by-step instructions:
Your Host Table
1. Acquire an unused Internet address from your Network
Administrator and choose a unique name for your AXIS 540/640.
2. Add the Internet address and host name to your system host table.
On most systems, this is done by appending the following line to
the /etc/hosts file:
<Internet address>
<host name>
Example:
192.168.3.191
npsname
3. Update your Alias Name data bases. If your system utilizes alias
name data bases such as Yellow Pages (YP) or Network
Information Services (NIS), you should update these. On most
systems this is done by entering the following commands:
cd /var/yp
make
Caution
DO NOT use the default or example Internet address when installing
your AXIS 540/640. Always consult your Network Administrator
before assigning an Internet address.
26
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Basic Installation
Set the Internet You may set the Internet address of the AXIS 540/640 in four
Address and Host different ways, using either arp, rarp, bootp, or dhcp. The main
Name characteristics of each of these methods are described below:
•
ARP - available in UNIX, Windows 95, and Windows NT. This
is generally considered to be the easiest method although it does
require the Internet address for each new device to be down-
loaded individually. It is not appropriate to use this method over
routers.
•
•
RARP - available in UNIX, it down-loads the Internet address to
each device automatically. It requires a rarp daemon on your
system, and operates within a single network segment only.
BOOTP - available in UNIX and quite similar to rarp, although it
can however operate on the entire network. Requires a BOOTP
daemon on your system. A request made to an active BOOTP or
RARP daemon initiates a search of the Ethernet Address Table
(RARP daemon), or Boot Table (BOOTP daemon) for an entry
matching the print server's Ethernet address. If a matching entry
is found, the daemon then down loads the Internet Address to the
print server.
•
DHCP - available in Windows NT and UNIX systems, it allows
for the automatic but temporary assignment of Internet addresses
from a central pool. In the absence of either an active RARP or
BOOTP daemon running on the host DHCP will, when enabled,
cause the selected host to automatically allocate and down load a
free Internet Address, Default Router Address and Net Mask to
the requesting print server. It also provides validation data that
defines how long the Internet addresses will remain valid.
The procedures for using each of the above methods are described in
detail below.
AXIS 540/640 User’s Manual
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Basic Installation
Notes: ❏ DHCP is only available in “+” and Token Ring models.
❏ Please note that although it is recommended practice to refer to
the host name when accessing your AXIS 540/640, it is perfectly
acceptable to replace this name with the Internet address in all
instances. Indeed, this becomes a necessity when:
•
•
the host name has not been included in your system host table
attempting to use the arp command in a Windows 95 or NT
environment.
The latter point is demonstrated in the first of the examples below.
Using ARP in Windows In both Windows 95 and Windows NT the Internet address can be set
95, Windows NT
using the arp method. Perform thefollowing commands to down-load
the Internet address and verify correct Internet communication.
AXIS 540/542 Ethernet Print Server:
Start a DOS window. Type the following command:
arp -s <Internet address> <Ethernet address>
ping <Internet address>
arp -d <Internet address>
Example:
arp -s 192.168.3.191 00-40-8c-10-00-86
ping 192.168.3.191
arp -d <192.168.3.191>
The host will return Reply from 192.168.3.191... or some
similar message. This indicates that the address has been set and the
communication is established.
28
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Basic Installation
AXIS 640/642 Token Ring Print Server:
Start a DOS window. Type the following command:
arp -s 802.5 <Internet address> <node address>
ping <Internet address>
arp -d <Internet address>
Example:
arp -s 802.5 192.168.3.191 00-02-31-48-00-61
ping 192.168.3.191
arp -d <192.168.3.191>
The host will return Reply from 192.168.3.191... or some
similar message. This indicates that the address has been set and the
communication is established.
Notes: ❏ Due to a bug in the Windows 95 implementation of arp you must
first, if you have an empty arp table (seen with arp -a), ping an
existing unit on your network before setting the IP number of
your AXIS 540/640.
❏ Please note that when you execute the ping command for the first
time, you will experience a significantly longer response time than
is usual.
❏ The arp -dcommand is advised so that the Internet to Ethernet
address information is stored as a dynamic parameter within the
host’s cache memory. Failure to execute this command will mean
that the mapping is static and consequently installed permanently
on the host.
AXIS 540/640 User’s Manual
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Basic Installation
Using ARP in UNIX You may also use the arp method for downloading the Internet
address within a UNIX environment:
AXIS 540/542 Ethernet Print Server:
Type the following command:
arp -s <host name> <Ethernet address> temp
ping <host names>
Example:
arp -s npsname 00:40:8c:10:00:86 temp
ping npsname
The host will return npsname is alive, or some similar message.
This indicates that the address has been set and the communication is
established.
AXIS 640/642 Token Ring Print Server:
Type the following command:
arp -s 802.5 <host name> <node address> temp
ping <host names>
Where the node address is either the serial number found on the
underside label of the AXIS 640/642 or a Locally Administrated
Address.
Example:
arp -s 802.5 npsname 00:02:31:48:00:61 temp
ping npsname
The host will return npsname is alive, or some similar message.
This indicates that the address has been set and the communication is
established.
30
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Basic Installation
Notes: ❏ The arp command can vary between different UNIX systems. The
802.5 argument is only required for IBM AIX systems, and some
BSD type systems expect the host name and node address in
reverse order. Furthermore IBM AIX systems will require the
additional argument ether. For example:
arp -s ether <host name> 00:40:8c:10:00:86 temp
❏ Please note that when you execute the ping command for the first
time, you may experience a significantly longer response time
than is usual.
Using RARP in UNIX Follow the step-by-step procedure below to use the rarp method:
AXIS 540/542 Ethernet Print Server
1. Append the following line to your Ethernet Address table. This is
typically performed using the command /etc/ethers:
<Ethernet address> <host name>
Example:
00:40:8c:10:00:86 npsname
2. Update your host table and alias name databases, as described
previously.
3. If it is not already running, start the rarp daemon. This is typically
performed using the command rarpd -a.
4. Restart the AXIS 540/542 to down-load the Internet address.
AXIS 540/640 User’s Manual
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Basic Installation
AXIS 640/642 Token Ring Print Server
If you are a IBM AIX user, you will probably not have access to a rarp
daemon. If this is the case, you may use either the arp or bootp
methods instead.
1. Append the following line to your Node Address table. This is
typically performed using the command /etc/ethers:
<node address> <host name>
Where the node address is either the serial number found on the
underside label of the AXIS 640/642 or a Locally Administrated
Address.
Example:
00:02:31:48:00:61 npsname
2. Update your host table and alias name databases, as described
previously.
3. If it is not already running, start the rarp daemon. This is typically
performed using the command rarpd -a.
4. Restart the AXIS 640/642 to down-load the Internet address.
32
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Basic Installation
Using BOOTP Follow these step-by-step procedure below to use the bootp method:
in UNIX
1. Append the following entry to your boot table. This is typically
performed editing the file: /etc/bootptab:
<host name>:ht=<hardware type>:vm=<vendor magic>:\
:ha=<hardware address>:ip=<Internet address>:\
:sm=<subnet mask>:gw=<gateway field>
Example for AXIS 540/542 /Ethernet:
npsname:ht=ether:vm=rfc1048:\
:ha=00408c100086:ip=192.168.3.191:\
:sm=255.255.255.0:gw=192.168.1.1
Example for AXIS 640/642 /Token Ring:
npsname:ht=tr:vm=rfc1048:\
:ha=000231480061:ip=192.168.3.191:\
:sm=255.255.255.0:gw=192.168.1.1
2. Update your host table and alias name databases as described
previously.
3. If it is not already running, start the bootp daemon. This is
typically performed using the command bootpd.
4. Restart the AXIS 540/640 to down-load the Internet address,
default router address, and net mask.
Notes: ❏ The htand vmfields must be entered exactly as in the example.
❏ The hafield is the Ethernet address and the ip field is the
Internet address of your AXIS 540/640.
❏ The gwand smfields correspond to the default router address and
net mask (DEF_ROUT and NET_MASK).
AXIS 540/640 User’s Manual
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Basic Installation
Using DHCP Follow these step-by-step procedure below to use the DHCP method:
in Windows
1. Edit or create a scope in the DHCP manager of the DHCP
daemon. The entries included into this scope should include the
following:
•
•
•
•
range of IP addresses
subnet mask
lease duration
default router IP address
2. Activate the scope
3. Enable the DHCP_ENB parameter in the Configuration file of
the AXIS 540/640 using AXIS NetPilot or any other preferred
method.
Note: ❏ DHCP is only available in “+” and Token Ring models.
34
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
NetWare
Section 3: Setting Up - NetWare
Section 3 Setting Up - NetWare
If you have not already done so, you should use the Installation
Wizard in AXIS NetPilot to install your network print server; refer to
Section 2 - Basic Installation.
After performing the basic installation, the AXIS 540/640 is ready for
printing within the NetWare environment. This section provides
information for making further adjustments to the configuration.
If you intend to operate your AXIS 540/640 in a multiprotocol
environment, you should also proceed to the other relevant sections in
this manual, namely:
Section 4 Setting Up - Windows
Section 5 Setting Up - OS/2
Section 6 Setting Up - Macintosh
Section 7 Setting Up - UNIX
Section 8 Web Based Management
Set Up using the AXIS NetPilot
You may use the AXIS NetPilot to:
•
•
•
set up the print queues, printers, and print servers.
set up the configuration parameters of the AXIS 540/640.
monitor the printers on the network.
Notes: ❏ AXIS NetPilot contains an extensive on-line help facility to assist
you with any of the operations listed above.
❏ The AXIS NetPilot software is designed to set up a range of
different network environments. Therefore you will encounter
windows that are relevant to other systems as well as NetWare.
Caution
Any network configuration should involve the Network
Administrator.
AXIS 540/640 User’s Manual
35
Download from Www.Somanuals.com. All Manuals Search And Download.
NetWare
Section 3: Setting Up - NetWare
Using AXIS NetPilot By opening folders from within the left hand pane of the AXIS
to Manage your
Print Servers
NetPilot main window you can:
•
•
•
from ‘Network Print Servers’ select any installed network print
server that you wish to configure, or
from ‘New Axis Units’ select any Axis network print server that
you wish to install using the Installation Wizard, or
from ‘Monitoring Printers’ select any group of printers that you
wish to monitor.
AXIS NetPilot’s main window
36
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
NetWare
Section 3: Setting Up - NetWare
Managing Printers Having installed your AXIS 540/640 print server in accordance with
and Print Queues the basic installation procedures described in Section 2 - Basic
Installation, your AXIS 540/640 should now feature in the Contents
of ‘Network Print Servers’ pane of the AXIS NetPilot Main window.
Examine Queues The NetWare Network Environment window detailed below, allows
and Servers you to examine all Print Queues and NetWare Print Servers
connected to the AXIS 540/640.
To gain access to this window, simply select the required Network
Print Server from AXIS NetPilot Main window, and then choose
Network from the Setup menu. Alternatively, you may click on the
Network Icon on the Toolbar. If you are not already, a dialog box will
then ask you to log on to your NetWare file server
The AXIS NetPilot NetWare Network Environment window
The AXIS 540/640 periodically updates the configuration by
searching the NDS tree or, in the case of NetWare versions 3.x, the file
servers.
AXIS 540/640 User’s Manual
37
Download from Www.Somanuals.com. All Manuals Search And Download.
NetWare
Section 3: Setting Up - NetWare
Print Queue To connect a print queue to a print server port, select the print server
Connection port you wish to connect from the NetWare Network Environment
window. Click Connect...
The Connect NetWare Print Queues window detailed below, will
then be displayed.
The AXIS NetPilot Connect NetWare Print Queues window
Select the location of the print queue from the Resources box.
Click either on an existing NetWare print queue for connection to the
server port, or alternatively create a new print queue by clicking on
Create Queue...
To define the method of printing to be used, select either Print Server
Mode or Remote Printer Mode. If you use Remote Printer Mode you
must enter the NetWare Print Server name, or make an appropriate
selection that will work with the AXIS 540/640 print server, using the
Browse... button.
Finally click the OK button to return to the Network Environments
window.
38
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
NetWare
Section 3: Setting Up - NetWare
Configuring via the Select the required Network Print Server and then Properties from the
Property Pages Setup menu in the NetPilot Main window, or alternatively click the
Properties Icon on the Toolbar. A comprehensive set of Property Pages
are then presented with an appropriate array of selection tabs.
A Property Page showing general parameters to be set
AXIS 540/640 Modes The AXIS 540/640 can run in either Print Server Mode or Remote
Printer Mode. The following overview explains the advantages and
limitations of each mode.
Property Pages: This is AXIS NetPilot’s way of allowing you to inspect
and change any of the AXIS 540/640 parameters.
There are different Property Pages for each of your
network environments. Simply click the NetWare tab
to gain access to the NetWare configuration.
AXIS 540/640 User’s Manual
39
Download from Www.Somanuals.com. All Manuals Search And Download.
NetWare
Section 3: Setting Up - NetWare
Print Server Mode In this mode the AXIS 540/640 logs in to a file server(s) and
repeatedly polls the print queues for print jobs. In this fashion, the
AXIS 540/640 emulates a NetWare print server, that is a workstation
running PSERVER. It provides high printing speed with low network
load and is the recommended mode for medium to large sized
networks. Each print server in PSERVER mode will occupy one
NetWare license.
Advantages
•
•
Easy to set up.
High performance (typically 150-400 kbytes/s).
Limitations
•
Requires a NetWare user licence for each AXIS 540/640 to file
server link.
Remote Printer Mode In this mode the AXIS 540/640 connects itself to a PSERVER
NetWare program running on the file server, or alternatively to a
dedicated workstation running PSERVER.EXE. It then automatically
receives print jobs from the file server. In this fashion, the AXIS
540/640 emulates a workstation running the NetWare remote printer
software RPRINTER, or NPRINTER. This mode is only
recommended for small networks where the number of NetWare user
licences is a major issue.
Advantages
Limitations
•
•
NetWare user licences are not required.
Easy to set up.
•
•
Lower performance, e.g. typically 20 - 70 kbytes/s for NLM.
Higher network load.
40
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
NetWare
Section 3: Setting Up - NetWare
Monitoring the For the purpose of printer monitoring the AXIS NetPilot allows users
Printers to create groups of printers. The printers comprising each group may
then be displayed in the AXIS NetPilot window. To examine the
status of any printer within a group, simply click on the appropriate
group folder icon. The status of each printer within a group is
displayed and also denoted by a relatively colored icon.
Any number of printer groups can be created and unwanted groups
can be deleted. Similarly, individual printers can be included or
deleted from any group. A printer may also be included in more than
one group, if required.
AXIS NetPilot’s Monitoring Window
AXIS 540/640 User’s Manual
41
Download from Www.Somanuals.com. All Manuals Search And Download.
NetWare
Section 3: Setting Up - NetWare
Other NetWare Configuration Methods
Novell Utilities After installing the AXIS 540/640 into the NetWare environment
using the AXIS NetPilot, adjustments to the configuration can be
made at any time, using the AXIS NetPilot. Alternatively, you may
wish to manage the AXIS 540/640 using either Novell’s NetWare
Administrator, or PCONSOLE.
Some useful features provided by the NetWare Administrator are
described in more detail below:
Printer Status The NetWare dialog Printer Status menu detailed below, shows the
status of an active print job serviced by an AXIS 540/640 network
print server. Detailed information concerning the active job is
displayed including, Print Queue, print job description, size of print
file, percentage of job completed, etc. The administrator also has the
ability to abort or pause the print job from this menu.
NetWare Administrator Printer Status Menu
42
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
NetWare
Section 3: Setting Up - NetWare
Notification Using the NetWare Administrator you may also enable/disable status
notification messages for printers connected to the AXIS 540/640, i.e.
Busy, Offline, Out of paper, Paper jam...etc. Print job owners and
chosen administrators may be added or removed from the list of
persons to be notified.
Print Layout A print layout of installed AXIS 540/640 Network Print Servers and
their relative print queues may be viewed for any NetWare
Organisational Unit. Summary information is also displayed simply
by right-clicking on the printer object you wish to examine.
NetWare Print Layout with corresponding summary information
AXIS 540/640 User’s Manual
43
Download from Www.Somanuals.com. All Manuals Search And Download.
NetWare
Section 3: Setting Up - NetWare
Web Browser If your network supports TCP/IP, you may configure the AXIS
540+/542+/640 and 642 models for operation within the NetWare
environment, using any standard Web browser. From the AXIS
NetWare Configuration Page you have the ability to change any
NetWare parameter. You can also monitor the status of your print
jobs, download software updates and access useful information. Refer
to Section 8 - Web Based Management for further information.
The AXIS 540+/542+ NetWare Configuration Page
FTP FTP provides another method for configuring the AXIS 540/640. For
further information refer to Editing using FTP, on page 98.
44
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Setting Up - Windows
Section 4 Setting Up - Windows
Having connected the AXIS 540/640 to your network, this section
now describes how to set up your AXIS 540/640 for printing in the
Windows environment.
The following Windows platforms are supported:
•
•
•
•
Windows 3.1 (requires add-on network support, see page 47)
Windows for Workgroups
Windows 95
Windows NT
If you intend to use the AXIS 540/640 in a multiprotocol
environment, you should also proceed to other relevant sections in this
manual, namely:
Section 3 Setting Up - NetWare
Section 5 Setting Up - OS/2
Section 6 Setting Up - Macintosh
Section 7 Setting Up - UNIX
Section 8 Web Based Management
Installation Using AXIS Print Utility for Windows
Unless you wish to change the default name of your AXIS 540/640,
the setup operation may be performed solely with the AXIS Print
Utility for Windows, which is supplied on the AXIS Utilities disk.
You should install this utility now if you have not already done so - see
the instructions on the AXIS Utilities disk label.
If you wish, you may change the default name of your AXIS 540/640
or amend any of the default parameters, using the AXIS NetPilot, or
any standard Web browser. Refer to Section 8 - Web Based
Management.
AXIS 540/640 User’s Manual
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Setting Up - Windows
Note: ❏ The AXIS Print Utility for Windows is not needed on the client
platforms for client-server printing.
About AXIS Print Utility for Windows is a dual purpose application for
AXIS Print Utility network printing in the Windows environment. It has two
for Windows fundamental purposes:
1. Install and maintain AXIS 540/640 printer ports as Windows
printer ports.
2. Capture and monitor print jobs directed to the AXIS 540/640
ports. Print jobs are directed through a spool directory either at
your local hard disk (peer-to-peer mode), or at the file server
(client-server mode). The printer port status of your AXIS
540/640 may be monitored and pop-up notification messages can
be generated, keeping you informed of completed print jobs or
any problematic condition.
For more information about AXIS Print Utility for Windows, see the
on-line help.
Notes: ❏ Microsoft Network (NetBIOS/NetBEUI) must be running when
using AXIS Print Utility for Windows.
❏ AXIS Print Utility for Windows must be running when printing
in peer-to-peer mode.
46
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Setting Up - Windows
Peer-to-Peer vs. All users requiring access to a network printer in peer-to-peer mode
Client-Server Printing will need to install the AXIS Print Utility for Windows software onto
their workstation. Users may then add the required network printer to
their systems and use the printer as if it was connected directly to their
workstation. Peer-to-peer printing affords the following benefits:
•
You can monitor the printer status at all times and be notified
when a print job is complete.
•
You do not have to rely on a server.
Client-server operation requires only one user to install theAXIS Print
Utility for Windows software onto their workstation. This user then
adds the printer to his or her workstation (the server) and shares the
printer with other users on the network. The other users (the clients)
may connect to the printer through the server via the Windows Print
Manager in Windows 3.1 and NT platforms, and the System Printers
folder in Windows 95 platforms.
The client-server mode provides a way of maintaining queue ordering
and job priority, but at a price. This is because:
•
•
You cannot receive printer status or print job notification.
The workstation set up as the server must be available at all times.
It must also have the capacity to handle the print jobs that pass
through it.
Notes: ❏ When using the client-server mode, other users may still install
the AXIS Print Utility for Windows software, for printing directly
to the network printer in Peer-to-Peer mode.
❏ When using the client-server mode, it is recommended that the
server is setup only on a Windows for Workgroups workstation.
Windows 3.1
In order to print to a network printer, Windows 3.1 requires the
installation of network support, such as the LAN Server or LAN
Manager Workstation software. When installed, proceed as described
under Windows for Workgroups below.
AXIS 540/640 User’s Manual
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Setting Up - Windows
Windows for Workgroups
Setup for Follow these steps to install your AXIS 540/640 for peer-to-peer
Peer-to-Peer Printing printing at a Windows for Workgroups workstation:
1. Double-click the AXIS Print Utility icon.
2. In the Port menu, click Add.
3. In the NPS Port list, select the AXIS 540/640 port to be installed.
The port will appear as <name>.LP1, where <name> is AX
followed by last six digits of your print server number
e.g. AX100086.LP1. However, this alphanumeric name will be
superseded by any new name given to your AXIS 540/640 when
using AXIS NetPilot.
4. Accept or change the suggested Windows port name and type any
required comment in the Description field. Make a note of the
Windows port name as you will need this later, then click OK to
install the Windows port.
5. In the Port menu, click Connect... to bring up the Windows
Printers dialog.
6. Select a printer driver from the list of Installed Printers (or click
Add>> to install a new driver), then click Connect...
7. Select the Windows port name from step 4 above (this name can
be found at the bottom of the Ports list).
8. Click OK to close the Connect dialog, and Close to close Printers.
The setup is completed and you can now print through your
AXIS 540/640.
Note: ❏ AXIS Print Utility for Windows must be running when you print
through your AXIS 540/640. We strongly recommend that you
copy the AXIS Print Utility icon into your StartUp folder.
.
48
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Setting Up - Windows
Client-Server Printing: Follow these steps to install your AXIS 540/640 for client-server
Server Setup printing at a Windows for Workgroups server:
1. Choose a workstation that you want to use as server for network
printing. The server must be available at all times and must have
2. Make sure that the printer sharing option is enabled. (Open
Network Setup, click Sharing..., check the ‘I want to be able to
allow others to print to my printer(s)’ box).
3. Install AXIS Print Utility for Windows on the server.
4. Set up your AXIS 540/640 as described under Setup for
Peer-to-Peer Printing, on page 53.
5. Open Print Manager and select your printer.
6. In the Printer menu, select Share Printer As...
7. Type a printer name in the Share As field (this is the printer name
seen by the clients, see Client Setup below).
Check the Re-share at Startup box, then click OK.
The server setup is now completed. Set up the clients as described
below.
Note: ❏ The AXIS Print Utility for Windows must be running when you
print through your AXIS 540/640. We strongly recommend that
you copy the AXIS Print Utility icon into your StartUp folder.
AXIS 540/640 User’s Manual
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Setting Up - Windows
Client-Server Printing: Follow these steps to use your AXIS 540/640 for client-server printing
Client Setup at a Windows for Workgroups client:
1. In the Control Panel, select Printers.
2. Select a printer driver from the list of Installed Printers (or click
Add>> to install a new driver), then click Connect...
3. Select Network...
4. In the Device Name list, select a local port (LPT1- LPT3) to
redirect to your network printer.
5. In the Show Shared Printers on list, select the server from Server
Setup above.
6. In the Shared Printers list, select the printer you want to use.
7. Click OK, OK and Close, then exit Control Panel.
The client setup is completed and you can now print through your
AXIS 540/640.
50
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Setting Up - Windows
Windows 95
Setup for Follow these steps to install your AXIS 540/640 for peer-to-peer
Peer-to-Peer Printing printing at a Windows 95 workstation:
1. Double-click the AXIS Print Utility icon.
2. In the Port menu, click Add.
3. In the NPS Port list, select the AXIS 540/640 port to be installed.
The port appears as <name>.LP1, where <name> is AX followed
by last six digits of your print server number e.g. AX100086.LP1.
However, this alphanumeric name will be superseded by any new
name given to your AXIS 540/640 when using AXIS NetPilot.
4. Accept or change the suggested Windows Port name, and type
any required comment in the Description field. Make a note of
the Windows port name as you will need this later, then click OK
to install the Windows port.
5. In the Port menu, click Connect to bring up the Printers folder.
6. Double-click the Add Printer icon. The Add Printer Wizard will
then guide you through the installation. Click Next to proceed.
7. Choose Local Printer, then click Next.
8. Choose Manufacturer and Printer, then click Next.
9. Select the Windows port name from step 4, then click Next.
10. Accept or change the suggested Printer Name, then click Next.
11. Click Finish to complete the installation.
The setup is completed and you can now print through your AXIS
540/640.
Note: ❏ AXIS Print Utility for Windows must be running when you print
through your AXIS 540/640. We strongly recommend that you
establish a shortcut to the AXIS Print Utility within your StartUp
file.
AXIS 540/640 User’s Manual
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Setting Up - Windows
on page 49.
Follow these steps to use your AXIS 540/640 for client-server printing
at a Windows 95 client:
1. Open the Network Neighborhood folder and select the server
being used by the printer. Refer to Client-Server Printing: Server
Setup on page 49.
2. Select the printer, and follow the Add Printer Wizard to setup the
printer on your client.
The client setup is completed and you can now print through your
AXIS 540/640.
52
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Setting Up - Windows
Windows NT
Setup for Follow these steps to install your AXIS 540/640 for peer-to-peer
Peer-to-Peer Printing printing at a Windows NT workstation:
1. Double-click the AXIS Print Utility icon.
2. In the Port menu, click Add.
3. In the NPS Port list, select the AXIS 540/640 port to be installed.
The port appears as <name>.LP1, where <name> is AX followed
by last six digits of your print server number e.g. AX100086.LP1.
However, this alphanumeric name will be superseded by any new
name given to your AXIS 540/640 when using AXIS NetPilot.
4. Accept or change the suggested Windows Port name, and type
any comments in the Description field. Make a note of the
Windows Port name as you will need this later, then click OK to
install the Windows Port.
5. In the Port menu, click Connect to bring up Print Manager.
6. In the Printer menu, click Create Printer.
7. Type a name in the Printer Name field, select a suitable printer
driver from the Driver list, and select Other... in the Print to list.
8. In the Print Destinations dialog, select Local Port, then click OK.
9. In the Port Name field, type: C:\~\<port>
where C:\~ is your spool directory, and <port> is the Windows
Port name from step 4. Click OK.
10. Close the Print Manager.
The setup is completed and you can now print through your AXIS
540/640.
Note: ❏ AXIS Print Utility for Windows must be running when you print
through your AXIS 540/640. We strongly recommend that you
copy the AXIS Print Utility icon into your StartUp folder.
AXIS 540/640 User’s Manual
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Setting Up - Windows
Client-Server Printing: To print in client-server mode from within a Windows NT
Client Setup environment, it is necessary to setup the server on a Windows for
Workgroups workstation. Refer to Client-Server Printing: Server Setup,
on page 49.
Follow these steps to use your AXIS 540/640 for client-server printing
at a Windows NT client:
1. Open Print Manager.
2. In the Printer menu, select Connect to Printer...
3. In the Shared Printers list, select the printer you want to use. Click
OK.
The client setup is completed and you can now print through your
AXIS 540/640.
Windows NT - LPD Printing
This section describes how to set up a Windows NT Server (ver. 3.5 or
later) for LPD printing over the TCP/IP protocol.
If you have not already done so, you should perform the TCP/IP basic
setup procedures prior to installing a printer for LPD printing. These
procedures are defined in Basic Set Up for TCP/IP, on page 25.
54
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Setting Up - Windows
Install the TCP/IP In the Control Panel, click the Network icon. If the TCP/IP Printing
Protocol Stack entry appears, then TCP/IP is already installed. Close the Network
folder and skip to Installing a Printer below.
Follow these steps to install the TCP/IP protocol stack:
1. In the Control Panel, select Network.
2. Click Add Software..., select “TCP/IP Protocol and related
components” and click Continue.
3. Check the “TCP/IP Network Printing Support” and click
Continue.
4. Select path and then click Continue.
5. Click OK in the Network Settings dialog box.
Installing a Printer Proceed as follows to install a printer for LPD printing.
1. In the Control Panel, click the Print Manager.
2. In the Printer menu, select Create Printer.
3. In the Printer Name field, type a name for your printer.
4. Choose a printer driver suitable for your printer.
5. In the Print to field, select Other...
6. In the Print Destinations dialog, choose LPR Port, then click OK.
The Add LPR Compatible Printer dialog now appears.
7. In the Name or Address field, type the IP address or the alias
name of your AXIS 540/640.
Note: If you use an alias name, this must be defined in the hosts
file on your server prior to the installation. This file is normally
located in /winnt35/system32/drivers/etc/hosts.
8. In the Name of Printer on the Machine field, type the logical
printer number you want to use, e.g. pr1. Click OK.
9. Click OK to complete the installation.
AXIS 540/640 User’s Manual
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Setting Up - Windows
Other Windows Configuration Methods
AXIS NetPilot After installing your printers using the AXIS Print Utility for
Windows adjustments to the AXIS 540/640 configuration can be
made at any time using the AXIS NetPilot.
Web Browser If your network supports TCP/IP, you may alternatively configure the
AXIS 540+/542+/640 and 642 models for operation within the
Windows environment, using any standard Web browser. Any
Windows parameter in the Configuration file may be amended from
within the NetBIOS/NetBEUI Configuration Page. Refer to Section 8
- Web Based Management for further information.
The AXIS 540+/542+ NetBIOS/NetBEUI Configuration Page
FTP FTP provides another method for configuring the AXIS 540/640. For
further information refer to Editing using FTP, on page 98.
56
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Setting Up - OS/2
Section 5 Setting Up - OS/2
Having connected the AXIS 540/640 to your network, this section
now describes how to set up your AXIS 540/640 for printing in the
OS/2 environment.
If you intend to operate your AXIS 540/640 in a multiprotocol
environment, you should also proceed to the other relevant sections in
this manual, namely:
Section 3 Setting Up - NetWare
Section 4 Setting Up - Windows
Section 6 Setting Up - Macintosh
Section 7 Setting Up - UNIX
Installation Using AXIS Print Utility for OS/2
The installation and setup operations are performed with the AXIS
Print Utility for OS/2. You should install this utility now if you have
not already done so - see the instructions on the OS/2 Utilities disk
label.
Should you require to change the default name of your AXIS 540/640
or amend any of default parameters use the AXIS NetPilot from any
Windows platform that is connected to your network, or WinOS/2
window under OS/2.
The AXIS Print Utility for OS/2 is not needed on the client platforms
when using a client-server configuration.
AXIS 540/640 User’s Manual
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Setting Up - OS/2
About AXIS Print AXIS Print Utility for OS/2 is a dual purpose application for network
Utility for OS/2 printing in the OS/2 environment. Its fundamental purpose is to:
1. Install and maintain the AXIS 540/640 printer port as an OS/2
printer port.
2. Capture and monitor print jobs directed to the AXIS 540/640
port. Print jobs may be directed through a spool directory either
at your local hard disk, or at the file server. The printer port status
of your AXIS 540/640 may be monitored and pop-up notification
messages can be generated, keeping you informed of completed
print jobs or any problematic condition.
Note: ❏ The NetBEUI protocol must be active. If not, use MPTS/LAPS
(LAN Server) or SETUP (LAN Manager) to activate it.
Install the AXIS 1. When AXIS Print Utility for OS/2 is running, click Install to
540/640
install your AXIS 540/640. It will then appear in the list as
<name>.LP1, where <name> is AX followed by last six digits of
your print server number. e.g. AX100086.LP1. However, this
alphanumeric name will be superseded by any new name given to
your AXIS 540/640 when using AXIS NetPilot.
2. Select the port that you wish to install, then click Install.
Repeat this procedure for each server using the AXIS 540/640.
Note: ❏ The AXIS Print Utility for OS/2 must be running in order to
print using your AXIS 540/640.
58
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Setting Up - OS/2
Integrating your AXIS 540/640 into the OS/2 Environment
Create a Print Queue 1. Double-click the Print Manager icon, click Setup, then select
(OS/2 version 1.x)
Printers...
2. Click Add to make a new printer definition, then type a name of
your choice in the Name field.
3. Select \PIPE\<name>.LP1 from the Device list, then select a
printer driver suitable for your printer.
4. Click Add, then click OK to confirm the printer definition.
5. Click Setup, then select Queues...
6. Click Add to create a print queue, and type a name in the Name
field.
7. Click Add, then click OK to confirm the queue definition.
Create a Print Queue 1. Double-click the Templates folder, then drag the Printer icon out
(OS/2 version 2.x
and OS/2 Warp)
to the Workplace Shell (or into a folder) while holding the right
mouse button down.
2. Type a name of your choice in the Name field.
3. Select \PIPE\<name>.LP1 from the Port list, and select a printer
driver suitable for your printer from the Standard Printer list.
4. Click OK to confirm the printer definition.
AXIS 540/640 User’s Manual
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Setting Up - OS/2
Share the Print A print queue must be made a shared resource before it can be
Queue accessed from other computers (clients or other servers).
Open an OS/2 window and issue the following command:
NET SHARE <queue_name> /PRINT
Where <queue_name> is the name of the queue created above.
To share a printer resource when using OS/2 Warp with IBM Peer
service, follow the steps below:
1. Click the right mouse button on the printer object.
2. Select Share and then Start sharing. In the dialogue box, enter a
Description.
3. Select the check-box Start sharing at LAN workstation startup.
4. Click OK.
To share a printer resource when using LAN server 4.0, follow the
steps below:
1. Open LAN Server Administration.
2. Open your domain and then Resource Definition.
3. Drag and drop a printer from the template.
4. Enter the Alias name, select a Server name and the previously
created Spooler Queue Name.
5. Click OK
The setup is completed and you can now print through your AXIS
540/640.
60
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Setting Up - OS/2
Other OS/2 Configuration Methods
AXIS NetPilot After installing your printers using the AXIS Print Utility for OS/2,
adjustments to the AXIS 540/640 configuration can be made at any
time using the AXIS NetPilot.
Note: ❏ The AXIS NetPilot runs in a WinOS/2 window.
Web Browser If your network supports TCP/IP, you may alternatively configure the
AXIS 540+/542+/640 and 642 models for operation within the OS/2
environment, using any appropriate Web browser, e.g. Netscape
Navigator for OS/2 Warp. Any OS/2 parameter in the Configuration
file may be amended from within the NetBIOS/NetBEUI
Configuration Page. Refer to Section 8 - Web Based Management for
further information
The AXIS 540+/542+ NetBIOS/NetBEUI Configuration Page
FTP FTP provides another method for configuring the AXIS 540/640. For
further information refer to Editing using FTP, on page 98.
AXIS 540/640 User’s Manual
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Setting Up - OS/2
62
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Setting Up - Macintosh
Section 6 Setting Up - Macintosh
Note: ❏ Please note that this section applies only to the print servers
supporting the Apple EtherTalk environment, i.e. AXIS 540+ and
AXIS 542+.
Having connected the AXIS 540+/542+ to your network, this section
now describes how to set up your AXIS 540+/542+ for printing in the
AppleTalk environment.
If you intend to operate your AXIS 540+/542+ in a multiprotocol
environment, you should also proceed to the other relevant sections in
this manual, namely:
Section 3
Section 4
Section 5
Section 7
Section 8
Setting Up - NetWare
Setting Up - Windows
Setting Up - OS/2
Setting Up - UNIX
Web Based Management
Installation Using the Chooser Window
Basic Configuration The basic configuration in the Apple EtherTalk environment is
performed simply by opening the Chooser window and selecting a
printer.
Chooser:
Selecting chooser from the Apple menu initiates a search
for available printers on the network. The available
printers, both physical and logical, are then subsequently
displayed with the names given them during
configuration. Default names are shown, unless they have
been modified.
AXIS 540/640 User’s Manual
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Setting Up - Macintosh
You may change the default name of your AXIS 540+/542+ or amend
any of default parameters if you wish. However, to access the config file
from a Macintosh you will need FTP support such as MacTCP, Fetch
or Anarchie. This is described in more detail at the back of this
section.
Choosing a Printer
Selecting a Printer The method of choosing a printer will vary depending on which
version of LaserWriter printer driver you are using.
•
The LaserWriter 7.0 driver assumes that you use a standard
PostScript driver, and cannot take advantage of any printer
specific features.
•
The LaserWriter 8.0 driver uses PPD files that contain printer
descriptions. This gives you full control over any features your
printer might have.
64
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Setting Up - Macintosh
LaserWriter 7.0 Open the Chooser window by starting the Chooser from the Apple
Printer Driver menu. Follow these steps to choose a printer:
1. Click the LaserWriter icon.
2. If your network has more than one zone, click on the zone you
want. If your network has no zones, this box does not appear.
3. Click the name of the printer you want.
The default AXIS 540+/542+ printer names are shown as:
AXIS<nnnnnn>_<port>, where <nnnnnn> is the last six digits of
the AXIS 540+/542+ serial number, and <port> is LPT1. For
example: AXIS100086_LPT1
4. Click the close box.
This completes the configuration and closes the Chooser.
Repeat this procedure for each Macintosh on the network using the
AXIS 540+/542+.
LaserWriter 8.0 Open the Chooser window by starting the Chooser from the Apple
Printer Driver menu. Follow these steps to choose a printer:
1. Click the LaserWriter 8.0 icon.
2. If your network has more than one zone click on the zone you
want. If your network has no zones, this box does not appear.
3. Click the name of the printer you want.
The default AXIS 540+/542+ printer names are shown as:
AXIS<nnnnnn>_<port>, where <nnnnnn> is the last six digits of
the AXIS 540+/542+ serial number, and <port> is LPT1. For
example: AXIS100086_LPT1
4. Click the ‘Setup...’ button, and then the ‘Auto Setup’ button. If
the printer supports bi-directional printing and the appropriate
PPD file is available, the installation will now be performed
automatically and you should proceed directly to step 6.
However, if this is not the case, the PPD file must then be selected
manually, as described in step 5.
AXIS 540/640 User’s Manual
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Setting Up - Macintosh
5. Choose the PPD file matching your printer, and click ‘OK’. If
your printer does not appear in the PPD file list, contact your
printer vendor. You may also use the Generic PPD if you do not
need any printer specific features.
6. Click ‘OK’, and then click the close box. This completes the
configuration and closes the Chooser.
Repeat this procedure for each Macintosh on the network using the
AXIS 540+/542+.
Bi-directional support The AXIS 540+/542+ allows the print-driver in the Macintosh to
directly communicate with the printer and consequently provides the
Mac-user with full access to the printer functionality, e.g. automatic
down-loading of fonts not resident in the printer. It is also able to
generate response messages to Macintosh printer queries, for older
printers without bi-directional support.
This functionality maintains backward compatibility with old printers
and Macintosh computers.
Verifying the Set Up You simply need to print a document from the Macintosh to verify
communication to the chosen printer. The basic installation can be
considered complete if the print test is satisfactory. The
AXIS 540+/542+ is now ready to use as a print server.
Note: ❏ For information on advanced EtherTalk functions such as non-
PostScript printer support, please refer to the Axis NPS Print
Server Technical Reference. You can obtain this from your dealer
or via the WWW. Refer also to Appendix E - How To Contact Axis.
ASCII, TBCP and BCP Binary Communication Protocol and Tagged Binary Communication
Protocol are communication protocols used by the serial and parallel
ports of a printer. They allow 8-bit binary data in files concurrent with
the use of some control characters, for communication and print job
control. TBCP is required for printing with a binary data stream on
some printers. e.g HP printers.
66
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Setting Up - Macintosh
You may select either ASCII or either of these binary data protocols
for your printing within the Macintosh environment, by following the
step by step instructions below:
1. Open the Chooser.
2. Select a network printer driver, any LaserWriter will do.
3. Select the printer port that has a name ending in "_CFG".
4. Close the Chooser.
5. Open a text editor, e.g. SimpleText.
6. Write a text file containing the following:
BINARY : YES
BINARY_TYPE : TBCP
The first parameter, BINARY, can take the values YES or NO.
The second parameter, BINARY_TYPE, can take the values BCP
or TBCP. See the technical reference for more information on
these parameters.
7. Print the above text file. The settings will be stored permanently
in the print server.
8. Open the Chooser and select the printer port you wish to use for
printing documents.
9. Close the Chooser.
10. Complete.
Other Macintosh Configuration Methods
Should you wish to change the AXIS 540+/542+ default name or
amend any of its default parameters from a Macintosh host, there are a
number of configuration methods that you may wish to consider.
AXIS 540/640 User’s Manual
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Setting Up - Macintosh
Web Browser If your network supports TCP/IP, you may alternatively configure the
AXIS 540+/542+ using an appropriate Web browser. Any AppleTalk
parameter in the AXIS 540+/542+ Configuration file may be amended
from within the AppleTalk Configuration Page. Refer to Section 8 -
Web Based Management for further information.
The AXIS 540+/542+ AppleTalk Configuration Page
AXIS NetPilot If you have a Windows platform connected to your network you may
wish to install and manage the AXIS 540+/542+ using the AXIS
NetPilot. Refer to Basic Set Up with AXIS NetPilot on page 22.
Using FTP FTP provides another method for configuring the AXIS 540/640.
To access the config file from a Macintosh you will need FTP support
such as MacTCP, Fetch or Anarchie. For further information refer to
Editing using FTP, on page 98.
68
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Setting Up - UNIX
Section 7 Setting Up - UNIX
Installation in the UNIX Environment
Having performed the basic TCP/IP setup procedures as defined in
Section 2 - Basic Installation, you are now able to print in interactive
mode using FTP or Reverse Telnet protocols.
However, should you require to integrate the AXIS 540/640 into your
host spooler you will now need to use the Axis automatic installation
script axinstall. This utility software is resident on the AXIS 540/640
and can be can be up-loaded to your host using FTP, so no disks or
tapes are required. Having completed this operation the printer
connected to the AXIS 540/640 will appear as though it is directly
connected to the host printer spooler.
If you intend to operate your AXIS 540/640 in a multiprotocol
environment, you should also proceed to the other relevant sections in
this manual, namely:
Section 3 Setting Up - NetWare
Section 4 Setting Up - Windows
Section 5 Setting Up - OS/2
Section 6 Setting Up - Macintosh
Section 8 Web Based Management
Note: ❏ The script axinstall is not available in theAXIS 540 and AXIS 542
models. However, this script may be uploaded from any other of
the AXIS print servers and used for configuring these models.
This script can also be downloaded from the AXIS Utilities
diskette or alternatively, obtained via the Axis WWW Home
Page, see Appendix C - Updating the Software.
AXIS 540/640 User’s Manual
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Setting Up - UNIX
Integration into the To integrate the AXIS 540/640 into the host printer spooler you will
Host Printer Spooler need to use the auto installation script axinstall, resident in the AXIS
540/640. You may install this software onto your host using FTP. To
do this, login to the AXIS 540/640 with this command:
ftp <host name>
where host name is the name assigned in your system host table,
(e.g. salesdept).
You will be prompted for user id and password. Use the user id root,
which has the default password pass (root is the user id with the highest
priority). Up-load the script using the command get axinstallas
shown in the example below.
Log out using the command quit,bye or exitdepending on your
FTP version.
> ftp salesdept
connected to salesdept.
220 AXIS 540/640 FTP Printer Server
ready.
Name (salesdept:thomas): root
331 User name ok, need password
Password: pass
(not visible)
230 User logged in
ftp> get axinstall
220 PORT command successful.
150 Opening data connection for axinstall
(192,36,253,4,13,223) (0 bytes), (mode ascii).
226 Transfer complete.
local: axinstall remote: axinstall
27545 bytes received in 4.1 seconds (6.5 kbytes/s)
ftp> bye
221 Goodbye.
>
Typical FTP session for collecting the axinstall script
70
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Setting Up - UNIX
The axinstall script has now been up-loaded to your host. Execute the
script with this command:
sh axinstall
You will be guided through the installation by a step-by-step
procedure. During the installation you will be asked to select a print
method; we suggest you choose LPD or, for more functionality, use
the PROS filter or named pipe methods. Please refer to the following
pages if you need guidance on the choice of print methods.
axinstall will suggest one of the systems listed below when started. If
you do not find the suggestion appropriate, then manually select any
of the systems listed.
1....SunOS 4 (SUN BSD, Solaris 1.x)
2....SunOS 5 (SUN SYS V, Solaris 2.x)
3....AIX (IBM RS/6000, BULL DPX 20)
4....HP-UX (HP 9000)
5....BOS (BULL DPX 2)
6....DEC OSF/1 (Digital Equipment, Alpha)
7....ULTRIX (Digital Equipment, DEC)
8....IRIX (Silicon Graphics, SGI)
9....SCO UNIX (Santa Cruz Operation)
10...FreeBSD (Berkeley UNIX)
11...Generic BSD (Berkeley UNIX)
12...Generic SYS V R3 (UNIX System V Release 3)
13...Generic SYS V R4 (UNIX System V Release 4)
Systems supported by axinstall
AXIS 540/640 User’s Manual
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Setting Up - UNIX
Print Methods on TCP/IP Networks
The AXIS 540/640 supports several different print methods in the
TCP/IP environment. axinstall will suggest a print method suitable for
your particular UNIX system, but you might want to use another
method depending on your printing requirements (banner pages,
status logging, etc.)
The diagram below shows the alternative data paths taken by some of
the UNIX print methods. This illustrates some of the advantages and
limitations of the different methods. Use the following information to
determine which method to adopt.
Print
Spooler
Directly
connected
printer
Devices
File to
Print
Filter/
Interface
Model
Parallel Port
Named Pipe
DIRECT
LPD FTP
RTELNET PROS B
FTP
PROS print
daemon
RTELNET
PROS A
Printer
AXIS 540/640
Illustration of different UNIX print methods
LPD The Line Printer Daemon is a protocol for transferring print jobs
between hosts. This is the recommended method for UNIX systems,
but some System V versions do not support LPD.
Advantages:
Easy to set up – install the AXIS 540/640 as a remote queue in
System V, or add a remote printer to /etc/printcapusing the
rmand rpfields (BSD).
Limitations:
Spooler features, and printcapor lproptions (BSD) such as
multiple copies, are not available.
72
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Setting Up - UNIX
FTP The File Transfer Protocol is used for transferring files between hosts.
Advantages:
Uses industry standard network software on the host.
Limitations:
No printer status logging. In the case of BSD it may conflict with
other input or output filters and does not allow both input and
output filters. In System V no filters or interface programs can be
used.
PROS A protocol developed at Axis.
Comes in two versions; named pipe (PROS A) and filter (PROS B).
PROS A
PROS A - Advantages:
The AXIS 540/640 appears as a device to the system. This makes
all filter and model options available. It provides accounting and
status logging. Supports bi-directional printing. The printer
information read back can be viewed in a log file.
PROS A - Limitations:
A ‘C’ compiler is required to build the PROS A drivers.
PROS B
PROS B - Advantages:
It provides accounting and status logging. Supports bi-directional
printing. The printer information read back can be viewed in a
log file.
PROS B - Limitations:
A ‘C’ compiler is required to build the PROS B drivers and in the
case of BSD, it may conflict with other input or output filters. It
does not allow both input and output filters. Interface programs
can not be used in System V.
AXIS 540/640 User’s Manual
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Setting Up - UNIX
Reverse Telnet Often used for printing via a terminal server printer port. Only
recommended if you already have a Reverse Telnet driver installed.
Advantages:
Easy to set up with previously installed Reverse Telnet drivers.
Limitations:
No status logging. Drivers are not supplied with the AXIS
540/640. Existing drivers may be slow.
Other UNIX Systems Most UNIX systems resemble either BSD or System V and so with
some ingenuity, a solution can be devised for other variants.
If the system has BSD socket type networking support, then prosbsd
(in the bsddirectory of the AXIS 540/640) can be used as a starting
point. It receives print data from stdin, and writes a log file to
stderr. Nothing is written to stdout.
Alternatively, FTP may be used. It is a good idea to use bsd/ftp_bsd
or sysv/ftp_sysvas a starting point.
OS/2 Systems If you are using OS/2 version 2.x and you wish to print through
TCP/IP, we recommend that you use the IBM TCP/IP for OS/2
product. It supports the LPD and interactive FTP print methods.
IBM MVS Systems A sample JCL script, jclex, is available in the mvsdirectory of the
AXIS 540/640. It gives an example of howto print a file from an MVS
mainframe to an AXIS 540/640 using FTP.
IBM AS/400 Systems Axis has produced a white paper covering AS/400 printing to Axis
network print servers. It is available on Internet via the Axis WWW
Home Page at http://www.axis.com/.
Windows NT If you are using Windows NT version 3.5 or later, you can use LPD
Systems printing over the TCP/IP protocol. For instructions on installing the
TCP/IP protocol stack on your Windows NT platform, refer to
Windows NT - LPD Printing on page 54.
74
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Setting Up - UNIX
Using Logical Printers The AXIS 540/640 has a powerful facility for altering the print data.
to Customise your This means that your desired print format can be realised on any type
Printing of printer. The following actions may be invoked from the AXIS
540/640:
•
The character set can be changed to suit the printer
•
•
•
•
Strings can be added before and after the print data
Strings within the print data can be substituted
ASCII to PostScript conversion
Hex Dump mode to assist with printing problems
If any of these actions are required a Logical Printer is used to change
the print data before being sent to the printer port. There are eight
logical printers that can be set up to filter the print data.
Edit the parameters in the AXIS 540/640 config file to configure a
logical printer. Refer to Appendix A - The Test Button. The default
logical printers settings are such that PR1 - PR4 cause no change to
the flow of print data, while PR5 - PR8 add CR to LF control
characters:
Logical Printer
PR1
Changes to data
no change
PR2
no change
PR3
no change
PR4
no change
PR5
add CR to LF
add CR to LF
add CR to LF
add CR to LF
PR6
PR7
PR8
Logical Printer: A logical printer acts as a filter between the network
and the physical printer. It appears to the user as a
normal printer with additional characteristics. For
example, a UNIX workstation may only send a line
feed (LF) to a shared printer that requires both a
carriage return (CR) and LF. The logical printer can
solve this problem by adding a CR.
AXIS 540/640 User’s Manual
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Setting Up - UNIX
Character Set A common problem in a multiple host environment is that different
Conversion hosts use different ASCII character sets. As a result of this, language
specific characters (such as å ü ô ñ) are sometimes printed incorrectly.
The AXIS 540/640 solution to this problem is to assign a character set
conversion filter to a logical printer, and then link that logical printer
to the host causing the problem.
There are several different filters to choose from within the
PR1_CSET Character Set Conversion. Refer to Appendix A - The Test
Button. The output from the conversion filter is always IBM PC Set 2
(Code Page 437), and this is the character set the printer must be set
up for.
Example:
The Problem: Your network contains three hosts using the
character sets IBM PC Set 2, ISO 8859-2, and DEC.
The Solution: In order to direct their print jobs to the same
printer you should assign each host to a separate logical printer,
and install character set conversion filters. Edit the following
entries in your config file:
PR1_CSET. : NONE
PR2_CSET. : ISO>IBM
PR3_CSET. : DEC>IBM
The Result:
Logical printer PR1 prints data transparently without conversion.
Logical printer PR2 converts ISO 8859-2 data to IBM PC Set 2.
Logical printer PR3 converts DEC data to IBM PC Set 2.
This arrangement will produce correct printouts for all language
specific characters.
76
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Setting Up - UNIX
Adding Strings Before These string functions provide a way to send printer control
and After Print Jobs commands before and after each print job. They may be specified
individually for each logical printer.
All strings are entered as hexadecimal byte values.
Example 1:
Assume that the logical printer PR5 is configured as a PostScript
printer. To append the PostScript End of File character
(Ctrl-D, hex 04) after each print job, edit the following entry in
your config file:
PR5_AFT. : 04
Example 2:
You have an HP LaserJet printer with dual input bins, and want
to print on pre-printed forms when using the logical printer PR4.
The standard forms are taken form bin 1, and the pre-printed
forms are taken from bin 2. The strings before and after print jobs
should then contain commands to select bin 2 (EC&l4H) and
bin 1 (EC&l1H) respectively. Edit the following entries in your
config file:
PR4_BEF. : 1B 26 6C 34 48
PR4_AFT. : 1B 26 6C 31 48
AXIS 540/640 User’s Manual
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Setting Up - UNIX
String Substitutions The string substitution function performs search and replace
operations on the print data. The primary application is to replace
printer control commands. Up to 20 string substitutions may be
specified individually for each logical printer.
All strings must be entered as hexadecimal byte values, and each match
and substitute string must be preceded by a count byte.
See Appendix A, PR1_STR String Substitutions.
Example 1:
To replace the UNIX New Line (hex 0A) with an ASCII NewLine
(hex 0D 0A) for logical printer PR1, edit the following entry in
your config file:
PR1_STR. : 01 0A 02 0D 0A
01is the match string count byte (length of the match string),
0Ais the match string,
02is the substitute count byte, and
0D 0Ais the substitute string.
This is the default setting for logical printers PR5 through PR8.
Example 2:
To replace the UNIX New Line (hex 0A) with an ASCII NewLine
(hex 0D 0A), and the printer command E G1(hex 1B 47 31) with
C
ECY(hex 1B 59) for logical printer PR2, edit the following entry
in your config file:
PR2_STR. : 01 0A 02 0D 0A 03 1B 47 31 02 1B 59
Note: ❏ Extensive use of string substitutions will naturally decrease the
throughput rate of the AXIS 540/640.
78
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Setting Up - UNIX
ASCII to Postscript The AXIS 540/640 logical printers can translate ASCII print data into
Conversion PostScript format. This makes it possible to print with a PostScript
printer from a host that does not support PostScript. The conversion
is selected by activating a filter that converts ASCII data into
Postscript. This filter may be activated individually for each logical
printer.
Example:
The following entries in your config file will allow print data
applied to PR1 to pass without changes, print data applied to PR2
will be converted from ASCII to PostScript, and PR3 data will be
searched - any ASCII data will be converted to PostScript, while
PostScript data will be allowed to pass without change.
PR1_FILT. : NONE
PR2_FILT. : POSTSCR
PR3_FILT. : AUTO_PS
The AUTO_PSconfiguration is used when you are not sure if the print
data is ASCII or PostScript.
When a logical printer is set for PostScript conversion it needs to
know the page size, page orientation, page formats and which font is
to be used. The default page size is A4 and the default page orientation
is Portrait, while the page format parameters are:
Page Format Parameter Default Value
Lines per page
Characters per line
Characters per inch
Lines per inch
Left margin
66
0
0=disable line wrap
10.0
60
30
50
60 = 60 lines per inch
30 = 3.0 mm
Top margin
50 = 5.0 mm
AXIS 540/640 User’s Manual
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Setting Up - UNIX
The PostScript font can be any font that is installed in the printer; if
no font is specified, Courier will be used.
Example:
The following entries are needed in your config file to set up
logical printer number 2 for ASCII to PostScript conversion with
the stated printing characteristics.
PR2_FILT.:POSTSCR
PR2_SIZE.:LETTER
(PostScript conversion on)
(page size = letter)
PR2_ORNT.:LANDS
PR2_FORM.:480120603050
(orientation = landscape)
(48 LPP, 0 CPL, 12 CPI, 6 LPI,
3 mm left margin, and
5 mm top margins)
PR2_FONT.:Helvetica
(font = Helvetica)
80
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Setting Up - UNIX
Read-back of The AXIS 540/640 supports bi-directional printing. The information
information from the printer is read back on the parallel port when the parameter
PRx_IN has the default setting of AUTO. However, it is required that
the printer also supports bi-directional printing. Through the
parameter PRx_IN the communication can be disabled.
Example:
The following entry is needed in your config file to disable the bi-
directional communication:
PR1_IN.
: NONE
(Read-back of information)
Debugging using the When hex dump mode is activated, the print data is printed as
Hex Dump Mode hexadecimal byte values rather than characters; printer control
commands are also printed as hex values. This allows you to inspect
what control and print characters are being sent to the printer, which
is a useful debugging facility for the more difficult printing problems.
Example:
The following is an example of the entries needed in your config
file to activate the hex dump mode for PR3:
PR3_DUMP.:YES
(switch on hex dump mode for PR 3)
Note: ❏ The page length for hex dump printouts is determined by the
lines per page value of the PostScript page format parameter.
AXIS 540/640 User’s Manual
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Setting Up - UNIX
Using Telnet with the AXIS 540/640
The Telnet support makes it possible to log in to the AXIS 540/640
and execute various commands as shown in the example below. Use
the following command to log in: telnet <host name>
> telnet salesdept
Trying 192.36.253.96...
Connected to salesdept.
Escape character is ‘^]’.
AXIS 540/640 TELNET Printer Server
AXIS 540/640 network login: root
Password: pass
(not visible)
AXIS 540/640 TELNET Printer Server
Root> help
Commands may be abbreviated:
logout
logout from TELNET
version
help
print current software version
print this list
status
show current printing status
show current account file
protocol restart of AXIS 540/640
reboot of AXIS 540/640
account
softreset
hardreset
defaults
Root> logout
Goodbye!
set default parameters in AXIS 540/640
Connection closed by foreign host.
>
Typical Telnet session to display available commands
Telnet support: Telnet is a TCP/IP command that allows you to
manage a remote system, in this case the AXIS
540/640. TheAXIS 540/640 has a number of built in
commands that can be executed via Telnet. Recent
firmware updates may have changed the commands
that are available, so use the help command (as shown
above) to list the Telnet facilities in your print server.
82
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Setting Up - UNIX
Viewing AXIS The accounting file contains data concerning the ten last print jobs. It
540/640 Accounting specifies an internal job number, the user that initiated the job, the
File using Telnet protocol and logical printer that was used, current status (Completed,
Offline, or Printing), number of bytes printed, elapsed time and off
line time. The file can be accessed using FTP or Telnet.
> telnet salesdept
Trying 192.36.253.96...
Connected to salesdept.
Escape character is ‘^]’.
AXIS 540/640 TELNET Printer Server
AXIS 540/640 network login: root
Password: pass (not visible)
AXIS 540/640 TELNET Printer Server
Root> account
Current account file:
JOB USER
PROT
LPR S BYTES ETIME OTIME
1 Thomas
2 Joe
3 RICHARD
4 MacUser
FTP
LPT
pr2 C 1885
pr1 C 23074 4
2
0
0
0
0
0
0
PSERVER pr2 C 43044 5
APPLE pr1 C 6717
2
5 LSLM_user NetBIOS pr2 C 36995 3
6 patrick
Root>
PROS
pr5 P 83208 9
Typical Telnet session to view the Accounting File
Note: ❏ Since the print server supports HTTP, the accounting of the
AXIS 540/640 may also be viewed using a Web browser. Click
Account on the AXIS 540/640 Home Page to examine the status
of any recent print jobs.
AXIS 540/640 User’s Manual
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Setting Up - UNIX
Viewing the The status command shows which printer port the logical printers are
AXIS 540/640s assigned to, and their current status.
Status using Telnet
> telnet salesdept
Trying 192.36.253.96...
Connected to salesdept.
Escape character is ‘^]’.
AXIS 540/640 TELNET Printer Server
AXIS 540/640 network login: root
Password: pass (not visible)
AXIS 540/640 TELNET Printer Server
Root> status
Current printer status:
PrinterPort Status Bytes printed Comments
pr1
pr2
pr3
pr4
pr5
pr6
pr7
pr8
LPT1 Printing 20916
LPT1 Occupied
LPT1 Occupied
LPT1 Occupied
LPT1 Occupied
LPT1 Occupied
LPT1 Occupied
LPT1 Occupied
Ready
Ready
Ready
Ready
Ready
Ready
Ready
Ready
Root>
Typical Telnet session to view logical printer status
Note: ❏ Since the print server supports HTTP, the accounting of the
AXIS 540/640 may also be viewed using a Web browser. Click
Status on the AXIS 540/640 Home Page to view logical printer
status.
84
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Setting Up - UNIX
Using SNMP for Remote Monitoring
You may use SNMP (Simple Network Management Protocol) for
remote monitoring of the AXIS 540/640. All major functions
applicable to print servers are supported.
General Information SNMP actually refers to a set of standards for network management,
including a protocol, a database structure specification, and a set of
data objects. The AXIS 540/640 SNMP implementation runs in the
TCP/IP environment.
The actual management is handled by an NMS (Network
Management System) software running on a host on your network.
The NMS software communicates with network devices by the means
of messages, which are references to one or more objects.
A message can be a question or an instruction to a device, or an alarm
triggered by a specific event in a device. Objects are contained in data
bases called MIBs (Management Information Base), where MIB-II is a
standard database.
The AXIS 540/640 supports all relevant parts of MIB-II. It also
includes a private enterprise MIB. The AXIS MIB is described later in
this section.
AXIS 540/640 User’s Manual
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Setting Up - UNIX
System Requirements The following requirements must be fulfilled in order to make full use
for SNMP of the AXIS 540/640 SNMP support:
•
An NMS software that allows you to install private enterprise
MIBs.
•
A host that supports FTP on which to run the NMS software.
Follow these steps to add the AXIS MIB to your NMS software:
1. Log in to the AXIS 540/640 using FTP.
2. Up-load the MIB file /snmp/axis.mib to the NMS host.
3. Install the AXIS MIB according to instructions in your NMS
software documentation.
Note: ❏ The AXIS MIB is not available in the AXIS 540 and AXIS 542
models. However, this can be uploaded from any other of the
AXIS print servers and used for configuring these models. This
file may also be downloaded from the AXIS Utilities diskette or
alternatively, obtained via the Axis WWW Home Page, see
Appendix C - Updating the Software.
The AXIS MIB The AXIS MIB contains a large number of objects which may be
categorised as follows:
•
•
•
Menu objects - used for viewing and changing the AXIS 540/640
configuration from the NMS program.Refer to Appendix A - The
Test Button.
Printer status and unit administration objects - used for
monitoring AXIS 540/640 print jobs and storing parameter
changes permanently.
Trap objects - used for alarms at various error conditions.
For technical details, you can view the MIB file (axis.mib) with any
text editor.
86
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Setting Up - UNIX
Other UNIX Configuration Methods
Web Browser You may alternatively configure the AXIS 540+/542+/640 and 642
models for operation within the TCP/IP environment, using an
appropriate Web browser. Any TCP/IP parameter in the AXIS
540/640 Configuration file may be amended from within the TCP/IP
Configuration Page. Refer to Section 8 - Web Based Management for
further information.
The AXIS 540+/542+ TCP/IP Configuration Page
FTP FTP provides another method for configuring the AXIS 540/640. For
further information refer to Editing using FTP on page 98.
AXIS 540/640 User’s Manual
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Setting Up - UNIX
88
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Internet
Windows
Section 8: Web Based Management
Section 8 Web Based Management
Having established TCP/IP communication as described in Section 2 -
Basic Installation, you are now able to access AXIS 540/640 series of
Network Print Servers from any standard Web browser.
Furthermore, the enhanced HTTP support available in the AXIS
540+/542+ and Token Ring models includes a quick and easy
management tool for performing all print server configuration tasks,
within all supported networking environments. Whether printing
from within a NetWare, UNIX, Windows, OS/2, Macintosh or a
mixed networking environment, you will find the ease with which you
can amend configuration parameters using HTTP, a considerable
benefit.
The information provided within this section will provide an
informative and valuable supplement to previous sections of this
manual that are relevant to your network. It describes how you may
access the Home Page of the AXIS 540/640 and also explains how the
unit may be configured for use within your local networking
environment.
After successfully navigating your way around the AXIS 540/640 Web
Pages you may proceed to one or more of the following sections, as
appropriate to your type of network.
Section 3 Setting Up - NetWare
Section 4 Setting Up - Windows
Section 5 Setting Up - OS/2
Section 6 Setting Up - Macintosh
Section 7 Setting Up - UNIX
AXIS 540/640 User’s Manual
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Internet
Windows
Section 8: Web Based Management
Accessing the Web Pages
Preparation To access the AXIS 540/640 Home Page the Internet Address must be
set, as described in Basic Set Up for TCP/IP, on page 25.
Accessing the Follow the steps below to access the Home Page of the AXIS 540/640.
Configuration Pages The browser used in the following example is Netscape Navigator 2.0.
1. Start the Netscape Navigator.
2. From the File menu, select Open Location...
3. Enter the Internet Address of the AXIS 540/640 as a URL in your
browser, as detailed below:
4. If you have assigned a host name, you may refer directly to the
host name instead:
5. The Home Page of your AXIS 540/640 will now be displayed in
your browser.
Note: ❏ The Home Page for the AXIS 540/542 models will differ from
that of the AXIS 540+/542+ and Token Ring models. This is due
to the enhanced HTTP support features that are provided in the
latter.
90
AXIS 560/660 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Internet
Windows
Section 8: Web Based Management
The AXIS 540/542 Home Page
From within the AXIS 540/542 Home Web Page you may view the
latest print jobs, printer port status and examine the current parameter
list, or default settings. Links to the AXIS Home and Product Pages
are also provided.
The AXIS 540+/542+ Home Page
The enhanced HTTP support features included in the AXIS
540+/542+ and Token Ring models are further described below.
AXIS 540/640 User’s Manual
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Internet
Windows
Section 8: Web Based Management
Enhanced HTTP Management Services
Links to the following services are available from the Home Page of
the AXIS 540+, 542+, 640 and 642 models:
•
•
•
•
•
Configuration
Management
Status
Account
Help
You can also visit Axis on the net, take a company tour and access any
of the Axis Network Print Server on-line services; including, manuals,
software updates, and technical support. You may also join the Axis
UserGroup for extended warranty and other valuable benefits.
Services Summary A summary of the enhanced services available from the AXIS
540+/542+/640/642 Home Page follows:
From within the Configuration pages you may:
•
modify configuration parameters of the AXIS
540+/542+/640/642.
A complete list of these parameters is contained in Appendix B -
The Parameter List.
•
enable and disable any of the available networking protocols and
modify their operation from appropriate configuration pages.
•
•
change the node address
amend the root password
Note: ❏ When clicking on either Management or Configuration for the
first time, you will be asked to provide a username and password.
By default these are set to rootand pass, respectively.
Caution
Any network configuration should involve the Network
Administrator.
92
AXIS 560/660 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Internet
Windows
Section 8: Web Based Management
The Management Page allows you to reset the print server and set the
parameters to the factory default values. You may also view basic
information about your the AXIS 540+/542+/640/642, i.e. the
current software version, ethernet address, serial number, base URL
address, enabled networking protocols.
User-friendly links to other services are also provided, including
Change root password.
You may view the status of the connected printer ports from the Status
Page, examine the number of bytes printed, etc.
Maintains and displays a historical record of print jobs that also
defines the user, logical printer, protocol, file size, elapsed time and
offline time.
The AXIS NetPilot Help utility is primarily designed to assist users
with the use of the AXIS NetPilot. However, the information
contained in this help utility is equally relevant to network
configuration and management activities that can be performed via
the internal Web Pages of the AXIS 540+/542+/640/642. An HTTP
version of the AXIS NetPilot Help facility is therefore made available
to assist you to with any of the operations detailed above.
AXIS 540/640 User’s Manual
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Internet
Windows
Section 8: Web Based Management
94
AXIS 560/660 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: The Test Button
Appendix A The Test Button
The Test Button is located on the front right hand side of the AXIS
540/640. By depressing this button you are able to:
•
•
Print a test page, to check the connection to the printer.
Print a parameter list, to define the current settings within your
AXIS 540/640.
•
Reset the AXIS 540/640 parameters to the original factory default
settings.
The functionality of the Test Button is determined by the power
status of the AXIS 540/640 and the number of times the button is
depressed.
A description of these functions complete with instructions for their
implementation, are detailed in the following sections of this
appendix.
The Test Page After connecting your printer to the port of your AXIS 540/640, it is
recommended that you print out a test page to verify that the cable
interface is functioning correctly. The simplest way to do this, is to
simply depress the Test Button once. The printed Test Page contains
basic information about the AXIS 540/640.
The Parameter List By simply double clicking on the Test button, the current parameter
settings installed in your AXIS 540/640 print server can be output to
the connected printer.
This list provides comprehensive details of all of the parameters and
their current status. The parameters may be changed according to your
requirements using the AXIS NetPilot software.
Note: ❏ Some of the parameters require that the AXIS 540/640 is restarted
before becoming effective.
AXIS 540/640 User’s Manual
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: The Test Button
Factory Default Should you wish to reset the AXIS 540/640 to the factory default
Settings settings, the best way to do this is to use the Test button. This
procedure involves switching the AXIS 540/640 off and on.
1. Remove the power cord to switch off the AXIS 540/640.
2. Press and hold down the Test button. Whilst continuing to press
the Test button, simultaneously switch on the AXIS 540/640 by
replacing the power cord. Keep theTest button pressed for at least
20 seconds after restoring power until the Network indicator
flashes at one second intervals.
3. Release the Test button and wait at least five seconds (five
indicator flashes).
4. Press and hold the Test button again for at least five seconds until
the Network indicator remains constantly lit.
The AXIS 540/640 is now reset to factory default settings. Restart the
AXIS 540/640 by switching it off and on.
Note: The Node address parameter NODE_ADDR will remain unchanged,
but all other parameters are reset. Should you wish to change the
Node address, you may do so via the General Property page, using
AXIS NetPilot.
96
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: The Parameter List
Appendix B The Parameter List
This appendix provides an overview of the AXIS 540/640 parameters
and describes how they may be edited. A sample parameter list is also
included. However, please note that because of recent print server
software updates, some differences may exist between the parameters
installed on your print server and those that are described within this
document.
Please refer to the AXIS Network Print Server Technical Reference for
a complete description of the parameters. Alternatively, you may wish
to access the Axis WWW Home Page at http://www.axis.com/, where
you can down-load the latest technical information. For details of the
appropriate WWW address in your region, please refer to Appendix E -
How To Contact Axis.
Editing the Configuration Parameters
Editing using All parameter settings are stored in the AXIS 540/640 config file,
AXIS NetPilot which may be edited via the Property Pages of the AXIS NetPilot
software. Each Property Page comprises an array of selection tabs that
are appropriate to your operating environments. Each parameter may
be defined by using the relevant box. For further information on the
Property Pages, please refer to Section 3 - Setting Up - NetWare.
Editing using a If your network supports TCP/IP you may view and edit the AXIS
Web browser 540/640 parameter list using any standard Web browser.
AXIS 540/640 User’s Manual
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: The Parameter List
Editing using The File Transfer Protocol provides another alternative for changing
FTP the parameter settings.
UNIX, Windows and Follow the step-by-step procedure below to edit the config file from
OS/2 Workstations UNIX, Windows and OS/2 workstations, using FTP:
1. Log in to the AXIS 540/640 by typing the command:
ftp <host name>
2. Enter rootas user id and passas password.
3. Up-load the config file by typing: get config
4. Edit the file using your preferred text editor.
5. Down-load the config file by typing:
put config CONFIG
Notes: ❏ It is important that the edited filename is specified in block
capitals. Otherwise, the edits are regarded as temporary and will
be lost once the AXIS 560/660 has been powered down.
❏ The method for performing file transfers using FTP can vary,
dependent upon which FTP application you are using.
Editing from a To edit the config file from a Macintosh you will need FTP support
Macintosh such as MacTCP, Fetch or Anarchie. The procedure for doing this is
the same as described for UNIX above.
Printing parameters The current parameter list may output to a printer connected to the
on the printer AXIS 540/640 by double-clicking the Test button.
98
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: The Parameter List
The Config File
The remainder of this appendix contains the complete AXIS 540/640
parameter list. The left-hand column shows the parameters and their
default values as they appear in the config file, and the right column
contains brief descriptions of the parameters.
Most parameters will take effect in the print server for the next
incoming print job after being changed. However, those parameters
marked (Requires Restart), will require the print server to be restarted
before the new parameter setting can take effect. Restart is also
required when the Ring Speed Switch is changed on the AXIS 640.
Please note that the password relates to parameters, e.g. ROOT_PWD
and PROS_PWD will only be shown when logged in as root, i.e. not
when printing the parameters using the Test button.
--- CONFIG MENU
NODE_ADDR.
BASE URL.
ROOT_PWD.
USERS.
: 00 40 8C 10 00 86
Node Address
Default Base URL Address (AXIS 540+/640+ only)
Root Password
User Authority and Printer Access
Token Ring Source Routing Mode (Only AXIS 640/642)
: WWW.AXIS.COM
: pass
:
S_ROUTE.
: auto
--- TCP/IP MENU
TCP_ENB.
: YES
TCP/IP Protocol Enabled
INT_ADDR.
DEF_ROUT.
NET_MASK.
PROS_PRT.
PROS_PWD.
LPD_BANN.
DHCP_ENB.
BOOTP_ENB.
RARP_ENB.
RTN_OPT.
: 192 36 253 80
: 0 0 0 0
: 0 0 0 0
: 35
Internet Address
Default Router Address (0.0.0.0 for no router)
Net Mask (e.g. 255.255.255.0 for class C, 0.0.0.0 for auto-sense)
PROS TCP Port Number
PROS Protocol Password
LPD Banner Page Disabled
DHCP Protocol Enabled
BOOTP Protocol Enabled
RARP Protocol Enabled
Reverse Telnet Options Enabled
PR1 Reverse Telnet TCP Port Number (0 for Disabled)
PR2 Reverse Telnet TCP Port Number (0 for Disabled)
PR3 Reverse Telnet TCP Port Number (0 for Disabled)
PR4 Reverse Telnet TCP Port Number (0 for Disabled)
PR5 Reverse Telnet TCP Port Number (0 for Disabled)
PR6 Reverse Telnet TCP Port Number (0 for Disabled)
PR7 Reverse Telnet TCP Port Number (0 for Disabled)
PR8 Reverse Telnet TCP Port Number (0 for Disabled)
: netprinter
: NO
: NO
: YES
: YES
: YES
: 0
RTEL_PR1.
RTEL_PR2.
RTEL_PR3.
RTEL_PR4.
RTEL_PR5.
RTEL_PR6.
RTEL_PR7.
RTEL_PR8.
: 0
: 0
: 0
: 0
: 0
: 0
: 0
AXIS 540/640 User’s Manual
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: The Parameter List
--- SNMP MENU
READ_COM.
WRT_COM.
: public
Read-Only Community Name
Read-Write Community Name
SNMP Trap Internet Address
SNMP Trap Community Name
System Contact
: pass
TRAPADDR.
TRAP_COM.
SYS_CONT.
SYS_NAME.
SYS_LOC.
: 0 0 0 0
: public
:
:
System Name
System Location
:
SNMP_AUT.
TRAP_PRT.
: DISABLE (DISABLE, ENABLE)
: DISABLE (DISABLE, ENABLE)
Authentication Failure Traps
Printer Traps
--- NETWARE MENU
NETW_ENB.
: YES
NetWare Protocol Enabled
Print Server Name (100086 are the last six digits of the serial number)
Print Server queue polling interval
Interval between automatic configuration checks
IEEE 802.3 Frame Type Enabled
Ethernet II Frame Type Enabled
IEEE 802.2 Frame Type Enabled
SNAP Frame Type Enabled
NetWare Burst Mode Enabled (Requires Restart)
File server & Name of print server (including context)
Bindery file server name
Bindery file server name
Bindery file server name
Bindery file server name
Bindery file server name
Bindery file server name
Bindery file server name
Bindery file server name
Bindery file server name
Bindery file server name
Bindery file server name
Bindery file server name
Bindery file server name
Bindery file server name
Bindery file server name
Bindery file server name
Print Server name. Slot
Print Server name. Slot
Print Server name. Slot
Print Server name. Slot
Print Server name. Slot
Print Server name. Slot
Print Server name. Slot
Print Server name. Slot
PS_NAME.
: AXIS100086
JOB_CHECK_DELAY.
CONF_CHECK_DELAY.
FR_802_3.
: 5
: 300
: YES
FR_ETH_2.
: YES
FR_802_2.
: YES
FR_SNAP.
: YES
NCP_BURST_MODE.
PSERVER_NDS.
: YES
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
PSERVER_BINDERY1.
PSERVER_BINDERY2.
PSERVER_BINDERY3.
PSERVER_BINDERY4.
PSERVER_BINDERY5.
PSERVER_BINDERY6.
PSERVER_BINDERY7.
PSERVER_BINDERY8.
PSERVER_BINDERY9.
PSERVER_BINDERY10.
PSERVER_BINDERY11.
PSERVER_BINDERY12.
PSERVER_BINDERY13.
PSERVER_BINDERY14.
PSERVER_BINDERY15.
PSERVER_BINDERY16.
NPRINTER1.
NPRINTER2.
NPRINTER3.
NPRINTER4.
NPRINTER5.
NPRINTER6.
NPRINTER7.
NPRINTER8.
100
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: The Parameter List
--- NetBIOS/NetBEUI MENU
LSLM_ENB.
NB_FR_TYPE.
LPRINT_1.
LLOGIC_1.
: YES
LAN Server/LAN Manager Protocol Enabled
Frame Type (Requires Restart)
Printer 1 Name (100086 are the last six characters of the serial number)
Printer 1 Logical Printer
: FR_AUTO (FR_AUTO, FR_802_2, FR_DIX)
: AX100086.LP1
: PR1 (PR1, PR2, PR3, PR4, PR5, PR6, PR7,
PR8, LPT1)
:
LPRINT_2.
LLOGIC_2.
Printer 2 Name
Printer 2 Logical Printer
: PR2 (PR1, PR2, PR3, PR4, PR5, PR6, PR7,
PR8, LPT1)
:
LPRINT_3.
LLOGIC_3.
Printer 3 Name
Printer 3 Logical Printer
: PR3 (PR1, PR2, PR3, PR4, PR5, PR6, PR7,
PR8, LPT1)
:
LPRINT_4.
LLOGIC_4.
Printer 4 Name
Printer 4 Logical Printer
: PR4 (PR1, PR2, PR3, PR4, PR5, PR6, PR7,
PR8, LPT1)
:
LPRINT_5.
LLOGIC_5.
Printer 5 Name (Not available in AXIS 540 and AXIS 542)
Printer 5 Logical Printer (Not available in AXIS 540 and AXIS 542)
: PR5 (PR1, PR2, PR3, PR4, PR5, PR6, PR7,
PR8, LPT1)
:
LPRINT_6.
LLOGIC_6.
Printer 6 Name (Not available in AXIS 540 and AXIS 542)
Printer 6 Logical Printer (Not available in AXIS 540 and AXIS 542)
: PR6 (PR1, PR2, PR3, PR4, PR5, PR6, PR7,
PR8, LPT1)
:
LPRINT_7.
LLOGIC_7.
Printer 7 Name (Not available in AXIS 540 and AXIS 542)
Printer 7 Logical Printer (Not available in AXIS 540 and AXIS 542)
: PR7 (PR1, PR2, PR3, PR4, PR5, PR6, PR7,
PR8, LPT1)
:
LPRINT_8.
LLOGIC_8.
Printer 8 Name (Not available in AXIS 540 and AXIS 542)
Printer 8 Logical Printer (Not available in AXIS 540 and AXIS 542)
: PR8 (PR1, PR2, PR3, PR4, PR5, PR6, PR7,
PR8, LPT1)
--- APPLETALK MENU (AXIS 540+ and AXIS 542+ only)
ATLK_ENB.
ATK_ZONE.
ZONER_EN.
ATK_FONT.
BINARY.
: YES
AppleTalk Protocol Enabled
AppleTalk Zone
HP Zoner Enabled
PostScript Font Set
Binary Transfer Enabled
:
: YES
: DEFAULT
: YES
(DEFAULT, 35N, ALL)
(TBCP, BCP)
BINARY_TYPE. : TBCP
Type of Binary Communication Protocol used if Binary Transfer (see
above) is enabled
APRINT_1.
ATYPE_1.
ALOGIC_1.
: AXIS100086_LPT1
: LaserWriter
Printer 1 Name (100086 are thelast six digits of the serial number)
Printer 1 Type
Printer 1 Logical Printer
: PR1 (PR1, PR2, PR3, PR4,
PR5, PR6, PR7, PR8, LPT1)
: AXIS100086_2
APRINT_2.
ATYPE_2.
ALOGIC_2.
Printer 2 Name
Printer 2 Type
Printer 2 Logical Printer
:
: PR2 (PR1, PR2, PR3, PR4,
PR5, PR6, PR7, PR8, LPT1)
AXIS 540/640 User’s Manual
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: The Parameter List
--- PRINTER1 MENU
PR1_WAIT.
PR1_IN.
: YES
: AUTO
:
(No function. Reserved for future use.)
PR1 Read-Back of information
PR1 String Before Print Job
PR1 String Substitutions
(NONE, AUTO)
PR1_BEF.
PR1_STR.
PR1_CSET.
:
: NONE
(NONE, ISO>IBM, 7UK>IBM, 7SW>IBM,
7GE>IBM, 7FR>IBM, 7ND>IBM, DEC>IBM)
(NONE, POSTSCR, AUTO_PS)
PR1 Character Set Conversion
PR1_FILT.
PR1_AFT.
: NONE
:
PR1 Printer Language Translation
PR1 String After Print Job
PR1_DUMP.
PR1_SIZE.
PR1_ORNT.
PR1_FORM.
PR1_FONT.
: NO
: A4
: PORTR
PR1 Hex Dump Mode
PR1 PostScript Page Size
PR1 PostScript Page Orientation
PR1 PostScript Page Format (MPL, MPP, CPI, LPI, LM, TM)
PR1 PostScript Font (Courier when not specified)
(A4, LETTER, LEGAL, EXECUT)
(PORTR, LANDS, R_PORTR, R_LANDS)
: 66 0 100 60 30 50
:
--- PRINTER2 MENU
PR2_WAIT.
PR2_IN.
: YES
: AUTO
:
(No function. Reserved for future use.)
PR2 Read-Back of information
PR2 String Before Print Job
PR2 String Substitutions
(NONE, AUTO)
PR2_BEF.
PR2_STR.
PR2_CSET.
:
: NONE
(NONE, ISO>IBM, 7UK>IBM, 7SW>IBM,
7GE>IBM, 7FR>IBM, 7ND>IBM, DEC>IBM)
(NONE, POSTSCR, AUTO_PS)
PR2 Character Set Conversion
PR2_FILT.
PR2_AFT.
: NONE
:
PR2 Printer Language Translation
PR2 String After Print Job
PR2_DUMP.
PR2_SIZE.
PR2_ORNT.
PR2_FORM.
PR2_FONT.
: NO
: A4
: PORTR
PR2 Hex Dump Mode
PR2 PostScript Page Size
PR2 PostScript Page Orientation
PR2 PostScript Page Format (MPL, MPP, CPI, LPI, LM, TM)
PR2 PostScript Font (Courier when not specified)
(A4, LETTER, LEGAL, EXECUT)
(PORTR, LANDS, R_PORTR, R_LANDS)
: 66 0 100 60 30 50
:
--- PRINTER3 MENU
PR3_WAIT.
PR3_IN.
: YES
: AUTO
:
(No function. Reserved for future use.)
PR3 Read-Back of information
PR3 String Before Print Job
PR3 String Substitutions
(NONE, AUTO)
PR3_BEF.
PR3_STR.
PR3_CSET.
:
: NONE
(NONE, ISO>IBM, 7UK>IBM, 7SW>IBM,
7GE>IBM, 7FR>IBM, 7ND>IBM, DEC>IBM)
(NONE, POSTSCR, AUTO_PS)
PR3 Character Set Conversion
PR3_FILT.
PR3_AFT.
: NONE
:
PR3 Printer Language Translation
PR3 String After Print Job
PR3_DUMP.
PR3_SIZE.
PR3_ORNT.
PR3_FORM.
PR3_FONT.
: NO
: A4
: PORTR
PR3 Hex Dump Mode
PR3 PostScript Page Size
PR3 PostScript Page Orientation
PR3 PostScript Page Format (MPL, MPP, CPI, LPI, LM, TM)
PR3 PostScript Font (Courier when not specified)
(A4, LETTER, LEGAL, EXECUT)
(PORTR, LANDS, R_PORTR, R_LANDS)
: 66 0 100 60 30 50
:
102
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: The Parameter List
--- PRINTER4 MENU
PR4_WAIT.
PR4_IN.
: YES
: AUTO
:
(No function. Reserved for future use.)
PR4 Read-Back of information
PR4 String Before Print Job
PR4 String Substitutions
(NONE, AUTO)
PR4_BEF.
PR4_STR.
PR4_CSET.
:
: NONE
(NONE, ISO>IBM, 7UK>IBM, 7SW>IBM,
7GE>IBM, 7FR>IBM, 7ND>IBM, DEC>IBM)
(NONE, POSTSCR, AUTO_PS)
PR4 Character Set Conversion
PR4_FILT.
PR4_AFT.
: NONE
:
PR4 Printer Language Translation
PR4 String After Print Job
PR4_DUMP.
PR4_SIZE.
PR4_ORNT.
PR4_FORM.
PR4_FONT.
: NO
: A4
: PORTR
PR4 Hex Dump Mode
PR4 PostScript Page Size
PR4 PostScript Page Orientation
PR4 PostScript Page Format (MPL, MPP, CPI, LPI, LM, TM)
PR4 PostScript Font (Courier when not specified)
(A4, LETTER, LEGAL, EXECUT)
(PORTR, LANDS, R_PORTR, R_LANDS)
: 66 0 100 60 30 50
:
--- PRINTER5 MENU
PR5_WAIT.
PR5_IN.
: YES
: AUTO
:
(No function. Reserved for future use.)
PR5 Read-Back of information
PR5 String Before Print Job
PR5 String Substitutions
(NONE, AUTO)
PR5_BEF.
PR5_STR.
PR5_CSET.
: 010A020D0A
: NONE
(NONE, ISO>IBM, 7UK>IBM, 7SW>IBM,
PR5 Character Set Conversion
7GE>IBM, 7FR>IBM, 7ND>IBM, DEC>IBM)
PR5_FILT.
PR5_AFT.
: NONE
:
(NONE, POSTSCR, AUTO_PS)
PR5 Printer Language Translation
PR5 String After Print Job
PR5_DUMP.
PR5_SIZE.
PR5_ORNT.
PR5_FORM.
PR5_FONT.
: NO
: A4
: PORTR
PR5 Hex Dump Mode
PR5 PostScript Page Size
PR5 PostScript Page Orientation
PR5 PostScript Page Format (MPL, MPP, CPI, LPI, LM, TM)
PR5 PostScript Font (Courier when not specified)
(A4, LETTER, LEGAL, EXECUT)
(PORTR, LANDS, R_PORTR, R_LANDS)
: 66 0 100 60 30 50
:
--- PRINTER6 MENU
PR6_WAIT.
PR6_IN.
: YES
: AUTO
:
(No function. Reserved for future use.)
PR6 Read-Back of information
PR6 String Before Print Job
PR6 String Substitutions
(NONE, AUTO)
PR6_BEF.
PR6_STR.
PR6_CSET.
: 010A020D0A
: NONE
(NONE, ISO>IBM, 7UK>IBM, 7SW>IBM,
PR6 Character Set Conversion
7GE>IBM, 7FR>IBM, 7ND>IBM, DEC>IBM)
PR6_FILT.
PR6_AFT.
: NONE
:
(NONE, POSTSCR, AUTO_PS)
PR6 Printer Language Translation
PR6 String After Print Job
PR6_DUMP.
PR6_SIZE.
PR6_ORNT.
PR6_FORM.
PR6_FONT.
: NO
: A4
: PORTR
PR6 Hex Dump Mode
PR6 PostScript Page Size
PR6 PostScript Page Orientation
PR6 PostScript Page Format (MPL, MPP, CPI, LPI, LM, TM)
PR6 PostScript Font (Courier when not specified)
(A4, LETTER, LEGAL, EXECUT)
(PORTR, LANDS, R_PORTR, R_LANDS)
: 66 0 100 60 30 50
:
AXIS 540/640 User’s Manual
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: The Parameter List
--- PRINTER7 MENU
PR7_WAIT.
PR7_IN.
: YES
: AUTO
:
(No function. Reserved for future use.)
PR7 Read-Back of information
PR7 String Before Print Job
PR7 String Substitutions
(NONE, AUTO)
PR7_BEF.
PR7_STR.
PR7_CSET.
: 010A020D0A
: NONE
(NONE, ISO>IBM, 7UK>IBM, 7SW>IBM,
PR7 Character Set Conversion
7GE>IBM, 7FR>IBM, 7ND>IBM, DEC>IBM)
PR7_FILT.
PR7_AFT.
: NONE
:
(NONE, POSTSCR, AUTO_PS)
PR7 Printer Language Translation
PR7 String After Print Job
PR7_DUMP.
PR7_SIZE.
PR7_ORNT.
PR7_FORM.
PR7_FONT.
: NO
: A4
: PORTR
PR7 Hex Dump Mode
PR7 PostScript Page Size
PR7 PostScript Page Orientation
PR7 PostScript Page Format (MPL, MPP, CPI, LPI, LM, TM)
PR7 PostScript Font (Courier when not specified)
(A4, LETTER, LEGAL, EXECUT)
(PORTR, LANDS, R_PORTR, R_LANDS)
: 66 0 100 60 30 50
:
--- PRINTER8 MENU
PR8_WAIT.
PR8_IN.
: YES
: AUTO
:
(No function. Reserved for future use.)
PR8 Read-Back of information
PR8 String Before Print Job
PR8 String Substitutions
(NONE, AUTO)
PR8_BEF.
PR8_STR.
PR8_CSET.
: 010A020D0A
: NONE (NONE, ISO>IBM, 7UK>IBM, 7SW>IBM,
PR8 Character Set Conversion
7GE>IBM, 7FR>IBM, 7ND>IBM, DEC>IBM)
PR8_FILT.
PR8_AFT.
: POSTSCR (NONE, POSTSCR, AUTO_PS)
PR8 Printer Language Translation
PR8 String After Print Job
:
PR8_DUMP.
PR8_SIZE.
PR8_ORNT.
PR8_FORM.
PR8_FONT.
: NO
PR8 Hex Dump Mode
PR8 PostScript Page Size
PR8 PostScript Page Orientation
PR8 PostScript Page Format (MPL, MPP, CPI, LPI, LM, TM)
PR8 PostScript Font (Courier when not specified)
: A4
(A4, LETTER, LEGAL, EXECUT)
: PORTR
(PORTR, LANDS, R_PORTR, R_LANDS)
: 66 0 100 60 30 50
:
--- OUTPUT MENU
L1_CENTR.
L1_BSYTM.
: HISPEED (IBM_PC, STNDRD, FAST, HISPEED)
: 60
LPT1 Centronics Interface Timing
LPT1 Busy Status Time-Out.All status reporting disabled if set to 0.
--- PANEL MENU
DEF_OUT.
: PR1
(PR1, PR2, PR3, PR4,
PR5, PR6, PR7, PR8, LPT1)
Internal Printout Destination
104
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C : Updating the Software
Appendix C Updating the Software
The following software can be updated:
•
•
•
•
•
•
AXIS NetPilot configuration software
AXIS Print Utility for Windows
AXIS Print Utility for OS/2
The AXIS 540/640 print server software held in Flash Memory
The axinstall script
The AXIS MIB file
All software updates are free of charge.
Obtaining the Updated Software
Over the Internet You may wish to check the Axis WWW Home Page at
http://www.axis.com/, where you can down-load the latest versions of
the software utilities.
Anonymous FTP Files and information are also available through anonymous ftp: log in
to ftp.axis.com and go to the /pub/axis directory.
Flash Memory The AXIS 540/640 server software is stored in Flash
Memory. This memory is provided by a silicon chip
that like any other ROM device, retains data content
even after power is removed.However, Flash Memory
is unique because it allows its data to be erased and
re-written. This means that you can install software
updates for your AXIS 540/640 as soon as they become
available, without having to replace any parts. The new
software is simply loaded into the AXIS 540/640 over
the network.
AXIS 540/640 User’s Manual
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C Updating the Software
Web Browser Because the AXIS 540/640 supports the HTTP protocol over
the Software Upgrade Page.
To display the Software Upgrade Page simply click the ‘Software
upgrade’ link within the Management Page. By following the
instruction provided you may then automatically initiate a file transfer
between the Axis Public Archive Server and your workstation. Once
the transfer is complete, you should then download this image file to
the AXIS 540/640 using FTP, as described in Upgrading over the
Network using FTP, on page 107.
Your dealer Contact your dealer to check if there have been any new releases of the
software. You should have your present version number ready to
compare against the latest software release.
Upgrading the Software
There are three methods with which to update to the AXIS 540/640
Flash memory:
•
•
•
through the parallel port LPT1, or
using the AXIS NetPilot, or
over the network using FTP on a TCP/IP network
The preferred methods are described below.
Note: ❏ Updating instructions are also supplied with the software update.
Updating Using the This is the most convenient method for updating AXIS NetworkPrint
NetPilot Server Software. An Installation Wizard is available to guide you
through thenecessary procedures, simply click on the Upgrade icon of
the AXIS NetPilot Toolbar to display the Upgrade Wizard menu.
106
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C : Updating the Software
Upgrading over the To upgrade over the network using FTP you will need the following:
Network using FTP
•
The file with the new print server software. The name of this file
is in the form product.version, e.g. 540_524.exefor software
release 5.24. You may use any of the aforementioned methods to
obtain the new file.
•
The AXIS 540/640 must also be installed on the network with
TCP/IP as described in Basic Set Up for TCP/IP, on page 25.
Follow the procedures below to upgrade the AXIS 540/640:
1. Log in to the AXIS 540/640 with the command
ftp <host name> where <host name> is the name assigned in
your system host table.
2. You will be prompted for user id and password. Use the user id
root, which has the default password pass (rootthe user id
with the highest priority).
3. Issue the command binary to change to binary transfer mode.
4. Issue the command put <software name> flash where
<software name>is the name of the new print server software,
e.g. 540.524.
5. Wait for the Flash load to finish. This normally takes 1 to 4
minutes. The unit will then automatically restart with the new
print server software.
Caution
❏ Be careful not to interrupt the file transfer. If the transfer is
interrupted the AXIS 540/640 may have to be re-initialized by
your dealer.
6. Log out using the command quit, bye or exitdepending on
your FTP version.
Notes: ❏ Should you encounter any problem that prevents a successful
upgrade over your network, it may become necessary to perform
the flash loading operation via the parallel port, LPT1. In this
instance, you are advised to contact your dealer, or Axis via the
WWW. Please refer to Appendix E - How To Contact Axis.
AXIS 540/640 User’s Manual
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C Updating the Software
108
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: Technical Specifications
Appendix D Technical Specifications
Supported Systems
Novell NetWare:
Versions 3.11, 3.12, 4.10 and above, supporting both NDS and Bindery
Emulation. Up to 16 file servers and 96 print queues can be served. User
messages are also supported.
Print Methods: RPRINTER/NPRINTER, PSERVER.
Microsoft LAN Manager:
IBM LAN Server:
LAN Manager 2.0c and above, running under OS/2 ver 1.3 and above.
LAN Server 1.3 and above, running under OS/2 ver 1.3 and above including
OS/2 Warp, OS/2 Warp Connect.
Microsoft Windows:
Windows NT ver. 3.5 and above, Windows for Workgroups, Windows 95.
UNIX:
All Operating Systems supporting the TCP/IP suite of protocols, including:
BSD 4.2, 4.3, 4.4, SunOS4 (Solaris 1.x), DEC Ultrix etc.
BSD Systems:
System V Systems: R3, R4, AT&T, Interactive, SCO, SunOS5 (Solaris 2.x), HP-UX, IBM AIX,
Silicon Graphics IRIX, DEC Alpha OSF/1, BULL (BOS, AIX).
Other Systems: IBM (MVS, VM, VSE, OS/400), DEC VMS, guidelines for other systems.
Print Methods: LPD, FTP, PROS (named pipe & filtered), Reverse Telnet.
Apple EtherTalk:
WWW:
(AXIS 540+/542+ only) Print Method: AppleTalk Phase 2.
Netscape Navigator 3.0 and MS internet explorer 3.0 or compatible
browsers.
Supported Protocols
NetWare:
IPX, SAP, RIP, SPX, SNMP and NCP (extended with NDS).
NetBIOS/NetBEUI or TCP/IP.
Windows and OS/2:
TCP/IP:
LPD, FTP, Telnet, Reverse Telnet, PROS, BOOTP, ARP, RARP, DHCP*
ICMP, IP, TCP, UDP, HTTP, SNMP.
Apple EtherTalk:
(AXIS 540+/542+ only) AARP, ATP, DDP, NBP, PAP, RTMP, ZIP.
Network Management SNMP-MIB II compliant, private enterprise MIB included.LAN Network
Manager for OS/2, Print server status in NWAdmin/PCONSOLE*.
Hardware
AXIS 540+/542+/640/642 32 bit RISC Controller, 1 Mbyte Flash memory. 256 kbytes RAM.
AXIS 540/542 32 bit RISC Controller, 512 kbyte Flash memory. 128 kbytes RAM.
*
“+” and Token Ring models only.
AXIS 540/640 User’s Manual
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: Technical Specifications
Logical Connection
AXIS 540/542 Running simultaneously any combination of the supported protocols. Use of
IEEE802.2, IEEE802.3, SNAP and Ethernet II frame types simultaneously.
AXIS 640/642 Running simultaneously any combination of the supported protocols. Use of
IEEE802.2 and IEEE802.5 (with Early Token release support for 16 Mbps),
frame types simultaneously.
Attachments
AXIS 540/540+ 10baseT (Twisted Pair) Ethernet.
AXIS 542/542+ 10base2 (Thin) Ethernet.
AXIS 640 Media type 3/RJ45/UTP. Support for 4 and 16 Mbps Token Ring networks.
AXIS 642 Media type 1/DB9/STP. Support for 4 and 16 Mbps Token Ring networks.
Security
UNIX:
Root password. User access list and printer access.
Encrypted passwords.
NetWare:
Logical Printers The logical printer ports can be programmed to perform auto ASCII to
PostScript conversion, string before and after job, string substitution,
alternative output and character set conversion.
Parallel Printer One IEEE 1284 compliant high-speed parallel port, 36-pin Centronics
connector. Sustained throughput up to 400 kbytes/s using NetWare or LAN
Server/LAN Manager. Bi-directional support for Apple, Reverse Telnet,
PROS.
Front Panel 2 LED indicators: Power and Network.
Test button for information printouts.
Slide switch for Token Ring speed (AXIS 640/642 only).
Power Consumption Power provided by external supply
AXIS 540/540+ Maximum 170 mA at 12 VDC. (Type PS-A, 9 V, 300 mA). Power can
optionally be provided by the printer (Centronics pin 18: 5 VDC, 300 mA).
AXIS 542/542+ Maximum 170 mA at 15 VDC. (Type PS-B, 12 V, 500 mA).
AXIS 640/642: Maximum 170 mA at 15 VDC. (Type PS-B, 12 V, 500 mA). An optional
jumper enables power provided by the printer (Centronics pin 18: 5 VDC,
350 mA).
Dimensions Height x Width x Depth
AXIS 540/540+ 1.1 x 2.2 x 4.7 inches (2.7 x 5.6 x 11.8 cm)
110
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: Technical Specifications
AXIS 542/542+ 1.1 x 2.9 x 4.7 inches (2.7 x 7.2 x 11.8 cm)
AXIS 640/642 1.1 x 2.2 x 4.7 inches (2.7 x 5.6 x 11.8 cm)
Weight 0.26 lb. (0.12 Kg)
Environmental Temperature: 40 - 105° F (5 - 40° C).
Humidity: 10 - 95% non-condensing.
Approvals
EMC:
EN 55022/1987, EN50082-1/1992. FCC Class A.
EN 60950.
Safety:
All specifications are subject to change without prior notice
AXIS 540/640 User’s Manual
111
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: Technical Specifications
112
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix E: How To Contact Axis
TIONS
COMMUNICA
Appendix E How To Contact Axis
Technical Support Should you require any technical assistance, please contact your Axis
dealer. If your questions can not be answered immediately, your Axis
dealer will forward your queries through the appropriate channels to
ensure that you get an expedient response.
Internet and If you are connected to Internet, please take the time to look at the
World Wide Web Axis WWW Home Page at http://www.axisinc.com/ or
http://www.axis.com/. Here you can find information about the
company and our products. You can also down-load on-line manuals,
tools such as the Acrobat Reader for different platforms, and the latest
versions of the software utilities. Your Axis dealer will be pleased to
provide you with any additional assistance or information that you
might require.
You may also access these pages directly AxisWWW Home Page from
the internal Web pages of the AXIS 540/640.
The Axis WWW Home Page.
AXIS 540/640 User’s Manual
113
Download from Www.Somanuals.com. All Manuals Search And Download.
TIONS
Appendix E: How To Contact Axis
COMMUNICA
FTP You may also obtain files and information through anonymous ftp:
log in to ftp.axisinc.com or ftp.axis.com and go to the /pub/axis
directory. Alternatively, enter ftp://ftp.axisinc.com/pub/axis or
ftp://ftp.axis.com/pub/axis in your WWW browser.
The Axis Bulletin Another way to access the Axisarchive is the Axis BBS. You will need a
Board System high-speed modem, a VT100 or VT220 terminal emulator and a
Kermit or ZModem compatible software. Dial +46 46 12 06 32 or
+46 46 211 94 53 and log in as guest (no password required).
The Axis Offices To contact an Axis office, choose the one nearest to your region:
Europe, Middle East, Axis Communications AB
Latin America,
Africa, Australia
Scheelevägen 16
S-223 70 Lund, Sweden
Phone: +46 46 270 18 00
Fax: +46 46 13 61 30
Email: [email protected]
URL: http://www.axis.com/
North America Axis Communications Inc.
4 Constitution Way, Suite G
Woburn, MA 01801-1030, USA
Phone: 1-800-444-AXIS, (617) 938-1188
Fax: (617) 938-6161
Email: [email protected]
URL: http://www.axisinc.com/
France Axis Communications SA
191 avenue Aristide Briand
94230 Cachan, France
Phone: +33 1 49 69 15 50
Fax: +33 1 49 69 15 59
114
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix E: How To Contact Axis
TIONS
COMMUNICA
Japan Axis Communications K.K.
8th Center Plaza 5F
1-10-16 Nihombashi Horidome-cho,
Chuo-ku, Tokyo 103, Japan
Phone: +81 3 3663 8801
Fax: +81 3 3663 8802
Email: [email protected]
Singapore, Axis Communications Pte Ltd.
Southeast Asia, 51 Thomson Road
The Pacific 187B Goldhill Centre
Singapore 307630
Phone: +65 250 8077
Fax: +65 352 1655
Email: [email protected]
Hong Kong, Axis Communications Ltd.
Northeast Asia, India
Room 602, Asian House, 1 Hennessy Road,
Wanchai, Hong Kong
Phone: +852 2836 0813
Fax: +852 2573 5935
Email: [email protected]
China Axis Communications Ltd. Beijing Office
Room 2203, 22/F, Everbright Building
6 Fu Xing Men Wai Street
Beijing 100045, China
Phone: +86 - 10 6856 1350
Fax: +86 - 10 6856 1359
Axis Communications Ltd. Shanghai Office
Room J, 6/F, World Trade Building
NO 1590 Yan An West Road
Shanghai 200052, China
Phone: +86 - 21 6280 8527
Fax: +86 - 21 6280 6892
AXIS 540/640 User’s Manual
115
Download from Www.Somanuals.com. All Manuals Search And Download.
TIONS
Appendix E: How To Contact Axis
COMMUNICA
116
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Index
A
E
Accounting File, 83
AIX, 31
Environmental, 111
Ethernet Address, 25
Alias Name, 26
F
Anonymous FTP, 114
Apple EtherTalk, 10, 63, 109
Approvals, 111
Factory Default Settings, 95, 99
Flash Memory, 105
FTP (File Transfer Protocol), 73
ARP, 27, 30
ASCII to Postscript Conversion, 79
Axis BBS, 114
AXIS MIB, 86
AXIS NetPilot, 36
Axis Offices, 114, 115
Axis WWW Home Page, 113
H
Hardware, 13, 109
Hex Dump Mode, 81
Host Name, 25, 26, 27
Host Printer Spooler (UNIX), 70
Host Table, 26
HTTP, 89
B
Basic Set Up, 25
HTTP, 20, 21
I
IBM, 31
NetPilot, 22
TCP/IP, 25
IBM AIX, 32
IBM AS/400 Systems Printing, 74
IBM LAN Server, 109
IBM MVS Systems Printing, 74
Installation Summary, 21
Installation using AXIS NetPilot, 35, 89
Internet, 113
Internet Address, 23, 25, 26, 27
Internet Axis Home Page, 113
IPX, 22
Bi-directional Printing, 73, 81
BOOTP, 27, 33
BSD Systems, 109
C
Character Set Conversion, 76
Config File, 99
Configuring
IBM OS/2, 57
Macintosh, 63
NetWare, 35, 89
UNIX, 69
L
LaserWriter 7.0 Printer Driver, 65
LaserWriter 8.0 Printer Driver, 65
Logical Connection, 110
Windows, 45
Connecting a Printer, 17
Logical Printers, 75
LPD (Line Printer Daemon), 72
LPD Printing from Windows NT, 54
D
Debugging Print Problems, 81
DEF_ROUT, 33
DHCP, 27, 34
Dimensions, 110
AXIS 540/640 User’s Manual
117
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Print Server Mode (NetWare), 40
Print Utility for OS/2, 58
Print Utility for Windows, 46
Property Pages, 39
PROS, 73
Protocols, 109
M
Macintosh, 10, 109
Microsoft LAN Manager, 109
Microsoft Windows, 109
Monitoring the Printers, 41
N
NDS, 37
NET_MASK, 33
NetBEUI/NetBIOS, 22
NetPilot, 36
Network Indicator LED, 15, 16
Network Information Services, 26
Network Management, 109
NIS, 26
Node Address, 25
Novell NetWare, 8, 109
R
RARP, 27, 31, 32
Remote Printer Mode (NetWare), 40
Reverse Telnet, 74
Ring Speed Switch, 16, 19
S
Security, 110
Set up of the Network, 20
Setting up
Macintosh, 63
NetWare, 35, 89
OS/2, 57
UNIX, 69
Windows, 45
O
OS/2 Systems, 9, 57
OS/2 Warp, 59, 109
OS/2 Warp Connect, 109
SNMP, 85
SPX, 22
Status, 84
P
Parameter Editing
From a Macintosh, 98
From a Windows Platform
(AXIS NetPilot), 97, 98
From TCP/IP, 98
String Functions, 77
String Substitutions, 78
Supported Systems, 109
System V Systems, 109
From the Web, 97
Parameter editing
T
TCP/IP, 22, 25, 109
Factory Defaults, 95, 96
Parameter List, 97
Peer-to-Peer Printing (Windows), 48
Ping Command, 31
Power Consumption, 110
Power Indicator LED, 15, 16
Print Methods, 109
Print Methods on TCP/IP Networks, 72
Print Problems, 81
TCP/IP Networks Print Methods, 72
Technical Specifications, 109
Technical Support, 113
Telnet, 82
Test Button, 15, 16, 96
Testing the Printer Connection, 17
Token Ring, 19
Print Queue (OS/2), 59
118
AXIS 540/640 User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
U
UNIX, 9, 69, 109
UNIX Print Methods, 72
Updating your Software, 105
W
Weight, 111
Windows, 9, 45, 109
Windows NT - LPD Printing, 54
Wizard, 23
World Wide Web, 113
Y
Yellow Pages, 26
AXIS 540/640 User’s Manual
119
Download from Www.Somanuals.com. All Manuals Search And Download.
|