Model AMP-610
500 Watt Stereo Amplifier
Owner's
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
HIGH PERFORMANCE STEREO AMPLIFIER
This power amplifier has been designed to provide high quality performance with a
minimumofmaintenance. However,it'sperformancewillonlybeasgoodasthecare
andqualityofcomponentswithwhichitisinstalled. Wethereforeadvisethatyouread
these instructions very carefully to familiarize yourself with the product and it's
features.
HELP!
1-800-645-4994
Monday
-
Friday
8:30am
9:00am
-
7:00pm Eastern
5:00pm Eastern
Should you require assistance with the installation or wiring of this unit, please call
our toll-free "HELP" line at 1-800-645-4994 during the days/hours shown.
Saturday
-
SPECIFICATIONS
MaximumOutputPower
4-ChannelOperation:
2-ChannelOperation:
Signal / Noise Ratio:
InputImpedance:
90dB(A-Weighted)
125 watts x 4
500 watts x 2
low-level 10K ohms
high-level100ohms
Output Power @ 1% T.H.D.
4-ChannelOperation:
2-ChannelOperation:
Input Sensitivity:
low-level 200 mv. - 5 v.
high-level 2 - 10 v.
600 watts RMS x 4
120 watts RMS x 2
Supply Voltage:
12 volts, negative ground
20 amps.
OutputImpedance:
2 - 8 ohms (stereo)
4 - 8 ohms (mono)
FuseRating:
Dimensions (W x H x D):
9"
x
2-1/4" x 10-5/8"
FrequencyResponse:
ChannelSeparation:
10 - 50,000 Hz. ± 1 dB
55 dB
230 mm x 57 mm x 270 mm
* Due to continuing improvement, Audiovox reserves the right to change features and design without notice.
-1-
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
1. Although this unit is designed with built-in self-protection circuits, there may be a possibility of damage if it is not wired
correctly. Please follow the wiring instructions carefully for the type of system being used.
2. The last lead to be connected is the wire to the positive (+) terminal of the battery. Connect this wire only after having
completed and checked all other connections to the amplifier.
3. By nature of its design, a power amplifier generates heat and requires good air circulation around it to dissipate that
heat. Do not install the amplifier in an enclosed area which does not permit adequate air circulation. Should the
temperature of the unit rise too high, the internal thermal sensors will shut off operation until it has cooled down
sufficiently.
4. If fuse replacement is necessary, use only fuses of the same ampere rating as originally supplied with the unit. The
use of fuses with incorrect ratings may cause serious damage to the amplifier. If fuses blow consistently, carefully
check all electrical connections to the unit.
5. Supply of adequate battery voltage is critical to the proper operation of the power amplifier. The leads to the battery
and chassis ground must be of a thick enough gauge to provide this voltage to the amplifier. We recommend
#16 gauge wire or thicker (smaller gauge #) for the battery and ground leads.
6. Make certain that the speaker(s) to be used with this amplifier are capable of handling the output power (wattage)
of the unit. Use of speaker(s) not rated for the output of this amplifier may cause damage to or failure of the
speaker(s) for which Audiovox will not be liable.
-2-
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATIONDIAGRAM
INSTALLATION INSTRUCTIONS
1. Select a mounting area where the amplifier will
have sufficient air circulation for proper cooling.
Inadequateaircirculationwillcausethetemperature
of the amplifier to rise and will trigger the
thermal protection mode.
2. Place the amplifier on the mounting surface
and mark the locations of the four mounting
holes as shown in the illustration.
3. Remove the amplifier and drill a 1/8" hole at
each of the four locations.
CAUTION: Before drilling the holes, look at the
underside of the mounting surface. Always
check carefully to avoid drilling into wiring,
braces, fuel or brake lines. CHECK BEFORE
YOU DRILL !
4. Secure the amplifier to the mounting surface
using the self-tapping screws provided.
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS AND INDICATORS
2
3
4
2
1
6
8
7
9
5
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Power Indicator/Protection Mode LED
The Power Indicator LED will light to indicate that the unit is connected to the battery and that the Remote Turn-On terminal is
receiving +12 volts, thus turning on the amplifier.
This LED illuminates red to indicate that the self-protection circuits have been activated and have shut off operation of the amplifier.
The protection circuits may be triggered by the temperature of the unit rising above a safe level or by an overload condition. If
activated by a rise in temperature, the unit will resume operation after cooling off to a normal operating range. If activated by
an overload condition, the source of the overload must be found and corrected to resume operation of the amplifier. Most
overload conditions are caused by mis-wiring or operation into incorrect speaker loads. Re-check all wiring and
connections if this situation occurs and correct as necessary.
2
Level (Gain) Control
The amplifier is capable of operating from sources supplying a wide range of input levels. The Level control should initially be set to
themid-rotationposition. Ifitisfoundthatthereisnotenoughoutputevenwhenthevolumecontrolonthecarstereoisatitsmaximum
setting, adjust the Level control to increase the output from the system. If, however, there is still output from the amplifier when the
car stereo volume control is at its minimum setting, or the output level increases too fast with a small rotation of the volume control,
adjust the Level control to decrease the output from the system. Once the correct setting is found, this control should not require any
further adjustment.
3
Low Level Input Connections
If low-level outputs are provided from the car stereo, it is recommended that the low-level inputs be used for lowest distortion
andbestperformance. UsegoodqualityshieldedaudiocableswithRCAplugsatbothendstoconnectthestereototheamplifier
and keep the cable lengths to a minimum to avoid noise.
CAUTION:
Use either the low-level or the high-level inputs on the amplifier.
DO NOT use both input levels at the same time.
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
4
High Level Input Connection
Ifthecarstereodoesnotprovidelow-leveloutputs,theamplifiermaybeconnectedviathespeaker(high-level)outputsfromthestereo.
Wire the speaker leads from the car stereo to the 5-pin adaptor harness as shown in the diagram (shielded cable is not required for
thisapplication)andplugtheconnectorintothematingHigh-LevelInputsocketontheamplifier. Carefullyspliceandinsulateallwire
connections.
5
Fuse
The circuitry of the amplifier is protected from damage by an automotive-type fast-blow fuse. If fuse replacement is necessary,
use only fuses of the same ampere rating as originally supplied with the unit. The use of fuses with incorrect ratings may cause
serious damage to the amplifier. If fuses blow consistently, carefully check all electrical connections to the unit.
6
Power Connection
The battery terminal (BATT) must be connected directly to the positive terminal of the vehicle battery to provide an adequate voltage
source and minimize noise. Connecting the battery terminal lead to any other point (such as the fuse block) will reduce the power
output and may cause noise and distortion. Use only #16 gauge or thicker (smaller gauge #) wire for this lead and connect it to the
terminal of the battery after all other wiring is completed.
7
Ground Connection
The ground terminal (GND) connection is also critical to the correct operation of the amplifier. Use a wire of the same gauge as the power
connection (#16 or thicker) and connect it between the ground terminal (GND) of the amplifier and a metal part of the vehicle close to the
mounting location. This wire should be as short as possible and any paint or rust at the grounding point should be scraped away to provide
a clean metal surface to which the end of the ground wire can be screwed or bolted.
8
Remote Turn-On Connection
The amplifier is turned on by applying +12 volts to the remote turn-on terminal (REM). The wire lead to this terminal should be connected to
the "Auto-Antenna" lead from the car stereo which will provide the +12 volts only when the car stereo is turned on. If the car stereo does not
-6-
Download from Www.Somanuals.com. All Manuals Search And Download.
provide an Auto-Antenna lead, the remote turn-on lead may be wired to an "Accessory" or "Radio" terminal in the car's fuse block. This will
turntheamplifieronandoffwiththeignitionkey,regardlessofwhetherthecarstereoisonoroff. Theremoteturn-onleaddoesnotcarrylarge
currents, so #20 gauge wire may be used for this application.
9
Speaker Connections
Dependingonthetypeandnumberofspeakersusedwiththeamplifier,wirethemtothespeakerterminalsaspertheappropriate
wiring diagram. For most applications, #18 gauge wire should be used for the speaker leads but in no case thinner than #20
gauge. Forleadsinexcessof10feet,#16gaugeisrecommended. Whenwiringthespeakers,paycarefulattentiontothepolarity
oftheterminalsonthespeakersandmakecertaintheycorrespondtothepolarityofthecorrespondingterminalsontheamplifier.
DO NOT ground any speaker leads to the chassis of the vehicle.
WIRING INSTRUCTIONS
The wiring of your amplifier will depend on the system and speakers you are using but will either be a stereo, mono, or mixed-
mono application. The following pages illustrate the input and output wiring for both types. Please refer to the appropriate
diagrams for the system configuration you are using.
The power and speaker wire connections for this amplifier are made via screw tightened terminal blocks. Loosen the screw
for the connection to be made and fully insert the wire (strip 1/2" of insulation from the end) into the respective screw on the side
panel (crimp-on "U" terminals are provided to simplify wiring and we recommend their use.) Tighten the screw down to secure
the wire. After initial set-up, the amplifier should not require any further adjustment unless there is a change in the car stereo
or speaker system with which it is used.
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
USETHISINPUTWIRINGWITH
OUTPUTWIRINGONPAGE 9
4-CHANNEL AND MIXED-MONO INPUT WIRING DIAGRAM
LOW-LEVEL
HIGH-LEVEL
(SPEAKER)OUTPUTS
CARSTEREO
RCA OUTPUTS
RIGHT FRONT
RIGHT REAR
LEFT REAR
RIGHT FRONT
+
LEFT FRONT
+
+
LEFT FRONT
+
RIGHT REAR
LEFT REAR
CHASSIS
ON RADIO
GROUND
5-PIN
CONNECTOR
IMPORTANT
USEEITHERHIGH-LEVELOR
LOW-LEVELINPUTS,NOTBOTH.
RCATYPE
SHIELDEDCABLES
(NOTINCLUDED)
CH4
CH3
CH1
CH2
-8-
Download from Www.Somanuals.com. All Manuals Search And Download.
USETHISOUTPUTWIRINGWITH
INPUTWIRINGONPAGE8
4-CHANNEL AND MIXED-MONO OUTPUT WIRING DIAGRAM
EXISTING SCREWORBOLT
CLEAN PAINT, RUST, DIRT OR
GREASE FROM AREA FOR GOOD
CONNECTION
SPEAKERIMPEDANCE
4-CHANNEL MODE : 2-8 OHMS
MIXED-MONO MODE : 4-8 OHMS
LEFTFRONT
SPEAKER
LEFTREAR
SPEAKER
RIGHTREAR
SPEAKER
RIGHT FRONT
SPEAKER
GROUNDEDMETAL
SECTIONOFVEHICLE
CONNECTTHIS
WIRELAST
USE#10GAUGE
WIRE(SEETEXT)
12VOLT VEHICLE
BATTERY
CHASSIS
GROUND
CAR STEREO
AUTO-ANTENNALEAD
CH3 / CH4
CH1 / CH2
MIXED-MONOSPEAKEROR
SUB-WOOFERWITHCROSSOVER
4-8 OHMS
MIXED-MONOSPEAKEROR
SUB-WOOFERWITHCROSSOVER
4-8 OHMS
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
USETHISINPUTWIRINGWITH
OUTPUTWIRINGONPAGE11
LOW-LEVEL
RCAOUTPUTS
3-CHANNEL INPUT WIRING DIAGRAM
CARSTEREO
MONO OR SUB-WOOFER
HIGH-LEVEL
(SPEAKER)OUTPUTS
LEFT
RIGHT REAR
LEFT REAR
+
RIGHT
CHASSIS
ON RADIO
GROUND
+
IMPORTANT
USEEITHERHIGH-LEVELOR
LOW-LEVELINPUTS,NOTBOTH.
RIGHT FRONT
LEFT FRONT
+
+
RCATYPE
SHIELDEDCABLES
(NOTINCLUDED)
5-PIN
CONNECTOR
TO CH2
TO CH1
TO CH4
-10-
Download from Www.Somanuals.com. All Manuals Search And Download.
USETHISOUTPUTWIRINGWITH
INPUTWIRINGONPAGE10
GROUNDEDMETAL
SECTIONOFVEHICLE
3-CHANNELOUTPUTWIRINGDIAGRAM
SPEAKER IMPEDANCE : 2 - 8 OHMS
(4 - 8 OHMS IN MIXED-MONO MODE)
LEFT
SPEAKER
RIGHT
SPEAKER
EXISTINGSCREWORBOLT
CLEAN PAINT, RUST, DIRT OR GREASE
FROM AREAFORGOODCONNECTION
MONOSPEAKER
OR
SUB-WOOFER
4-8 OHMS
USE#10GAUGE
WIRE(SEETEXT)
CONNECTTHIS
WIRELAST
12VOLT
VEHICLE
BATTERY
CHASSIS
GROUND
CAR STEREO
AUTO-ANTENNALEAD
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
USETHISINPUTWIRINGWITH
OUTPUTWIRINGONPAGE 13
2-CHANNEL MONO (BRIDGED) INPUT WIRING DIAGRAM
LOW-LEVEL
CARSTEREO
RCAOUTPUTS
HIGH-LEVEL
(SPEAKER) OUTPUTS
RIGHT
LEFT
RIGHT REAR
LEFT REAR
+
IMPORTANT
USEEITHERHIGH-LEVELOR
+
CHASSIS
ON RADIO
GROUND
LOW-LEVELINPUTS,NOTBOTH.
RIGHT FRONT
LEFT FRONT
+
5-PIN
+
CONNECTOR
W H I T E
RCATYPE
SHIELDEDCABLES
(NOTINCLUDED)
GREEN
BLACK
BROWN
G R A Y
TO CH1
TO CH4
-12-
Download from Www.Somanuals.com. All Manuals Search And Download.
USETHISOUTPUTWIRINGWITH
INPUTWIRINGONPAGE12
2-CHANNEL MONO (BRIDGED) OUTPUT WIRING DIAGRAM
EXISTING SCREW OR BOLT
CLEANPAINT,RUST,DIRTORGREASEFROM AREAFORGOOD
CONNECTION
RIGHTSPEAKER
LEFTSPEAKER
OR
OR
SUB-WOOFER
SUB-WOOFER
4 - 8 OHMS
4 - 8 OHMS
GROUNDEDMETAL
SECTIONOFVEHICLE
USE#10GAUGE
WIRE(SEETEXT)
CONNECTTHIS
WIRELAST
12 VOLT
VEHICLE
BATTERY
CHASSIS
GROUND
CAR STEREO
AUTO-ANTENNALEAD
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
90 DAY/12 MONTH LIMITED WARRANTY
Applies to car stereo power amplifiers, equalizers and accessories.
AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof,
under normal use and conditions, be proven defective in material or workmanship within 90 days from the date of original purchase, such
defect(s) will be repaired or replaced with new or reconditioned product (at the Company's option) without charge for parts and repair labor.
After the initial 90 day period and for a period of 12 months from the date of original purchase, the Company will supply at no charge a
replacement for any defective part(s) but will charge for the labor to repair the product.
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated
bill of sale), specification of defect(s), transportation prepaid, to an approved warranty station or the Company at the address shown below.
This Warranty does not extend to the elimination of externally generated static or noise, to correction of antenna problems, to costs incurred
for installation, removal or reinstallation of the product, or damage to tapes, compact discs, speakers, accessories, or vehicle electrical
systems.
This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through
alteration, improper installation, mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial number/bar code
label(s). THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT
PROVIDEDABOVEAND,INNOEVENT,SHALLTHECOMPANY'SLIABILITYEXCEEDTHEPURCHASEPRICEPAIDBYPURCHASERFOR
THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY
OF MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY
WARRANTYHEREUNDERINCLUDINGANYIMPLIEDWARRANTYOFMERCHANTABILITYMUSTBEBROUGHTWITHINAPERIODOF30
MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. No person or
representative is authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage
so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
U.S.A. : AUDIOVOX CORPORATION, 150 MARCUS BLVD., HAUPPAUGE, NEW YORK 11788 l 1-800-645-4994
CANADA: CALL 1-800-645-4994 FOR LOCATION OF WARRANTY STATION SERVING YOUR AREA
128-5422A
128-6098
-14-
Download from Www.Somanuals.com. All Manuals Search And Download.
|