Model PRO-9675FT4
Owner's Manual
4 Button Remote Start Security System With
Plug-In Shock Sensor & Starter Disable
FEATURES :
w 2 Four Button Programmable RF Transmitters
w Four Channel Code Learning Receiver (capable of accepting 4 transmitters
w Anti Code Grabbing Technology
)
w Selectable Manual Override Mode
w Remote Panic in all modes
w Protected Valet/Override
w Remote Start Safety Control Switch
w Selectable Automatic Timed Start Mode
w User Programmable Manual Override Code
w 7 Function LED - Arm / Disarm / Zone 1 / Zone 2 / Zone 3 / Valet / Arming
w Intrusion Alert with Memory
w Audible Arm / Disarm / Defective Zone / Tamper Confirmation
w Instant Siren Activation All Entry Points
w Starter Disable When Armed
w True Last Door Arming
w Defective Zone By-Pass
w Active or Passive Arming Selectable
w Programmable Auto Lock On / Off
w Programmable Auto Unlock / Off/Drivers Door/All Doors
w Programmable Door Lock Pulse Duration 1 Second / 3.5 Seconds/1 Sec L/ Dbl. U/L
w Programmable Active or Passive Door Locks
w User Programmable Permanent Chirp Delete
w On Command RF Chirp Delete from Transmitter Or Selectable Through Software
w 6 Tone Multi Tone Siren
w Car Horn Activation for additional alarm response
w Additional Negative Trigger Input
w RF Inhibit with ignition on
w Parking Light Flasher
w Remote Keyless Entry With Optional Access Guard (must have power door locks)
w Illuminated Entry
w Plug In Dual Stage Shock Sensor
OPTIONS :
w Remote Trunk Release (must have electronic trunk release)
w Multiple Vehicle Capable
w Remote Power Window Roll Up
w Remote Garage Door Interface
CAUTION ! Be certain that the vehicle is outdoors before using this or any remote
vehicle starting device. A running engine produces dangerous carbon
monoxide fumes which can be harmful or fatal if prolonged exposure
occurs. DO NOT remote start the vehicle if it is garaged.
Download from Www.Somanuals.com. All Manuals Search And Download.
opened during the 30 second arming cycle, arming will be suspended. When all entry points
are closed, the arming cycle will begin again.
At the end of the 30 seconds, the parking lights will flash once, the siren will chirp once, and
the dash mounted LED will begin to flash slowly confirming the system is armed. If the siren
did not sound when arming, then the chirps have been turned off. Refer to the section on
"Eliminating the Arm/Disarm Chirps" shown later in this manual. Passive door locking is a
selectable feature. If you have the optional door lock/unlock circuit installed, the doors may or
may not lock passively depending upon the setup during installation.
PROTECTION WHILE THE SYSTEM IS ARMED:
Opening any protected entry point, hood, trunk, or doors will cause the alarm to trigger
immediately. The siren will sound and the parking lights will flash for 30 seconds, then stop
and continue to monitor all protected entry points. If the thief left the door opened, the unit will
sound for six 30 second cycles then shut down, isolate the triggered zone and continue to
protect all other zones.
Whenever the system is armed, the dash mounted LED will slowly flash. This serves as a
visual deterrent to a potential thief. This LED is a very low current light emitting diode, and will
not cause the battery to drain even if left unattended for long periods of time.
Whenever the system is triggered, the vehicle's parking lights will flash for the full siren
sounding period. Optional - whenever the system is triggered, the interior courtesy light will
flash for the full siren sounding period.
Whenever the system is armed, the vehicle starter circuit is disabled, and the vehicle will not
start with the ignition key.
Whenever the system is armed, any strong impact to the vehicle will cause the shock
detector to trigger the alarm. Any lesser impact will cause the pre-detect stage of the shock
sensor to emit a few short series of warning tones from the siren.
DISARMING THE SYSTEM:
As you approach the vehicle, press and release the Unlock button on the keychain transmitter.
The parking lights will flash two times, the siren will chirp twice, and the dash mounted LED
will turn off.
If you have the optional door Lock/Unlock circuit installed, the doors will unlock. If you have
the optional entry illumination circuit installed, the interior light will turn on for 30 seconds or
until the ignition key is switched on.
Note: If the passive arming mode was selected at time of installation, the dash mounted LED
will start flashing rapidly indicating that the system is rearming. Opening any door will
suspend the automatic arming.
If the parking lights flashed three times, and the siren chirps four times, this indicates that the
alarm system was triggered during your absence. Before turning on the ignition key, examine
the dash mounted LED's flash pattern. The number of flashes identifies the triggered zone.
For additional information, refer to INTRUSION WARNING SIGNALS found later in this manual.
If the siren did not sound upon disarm, then the chirps have been turned off. Refer to the
sectiontitledELIMINATINGTHEARM/DISARMCHIRPS.
Note: If the optional 2 step door unlock circuit is installed, when the unlock transmitter button
is activated, the drivers door only will unlock, pressing the unlock button a second time
will cause all doors to unlock.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
SILENTDISARMING:
1. As you approach the vehicle, press and hold the Unlock button of your key chain
transmitter for two seconds.
The parking lights will flash twice, and the dash mounted LED will turn off confirming that the
system is disarmed. The siren will not chirp. If you have the optional door lock/unlock circuit
installed, the doors will unlock. If you have the optional entry illumination circuit installed, the
interior light will turn on for 30 seconds or until the ignition key is switched on.
Note: If the passive arming mode was selected at time of installation, the dash mounted LED
will start flashing rapidly indicating that the system is rearming. Opening any door will
suspend the automatic arming.
If the parking lights flashed three times, and the siren chirps four times, this indicates that the
alarm system had been triggered in your absence. Before turning on the ignition key, examine
the dash mounted LED's flash pattern. The number of flashes identifies the triggered zone.
For additional information, refer to INTRUSION WARNING SIGNALS found later in this manual.
Note: If the optional 2 step door unlock circuit is installed, when the unlock transmitter button
is activated, the drivers door only will unlock, pressing the unlock button a second time
will cause all doors to unlock.
WHILETHESYSTEMISSOUNDING
If during a triggered state, you wish to shut off the siren without disarming your security
system, simply press and release any transmitter button other than the disarm button. This
action will turn off the siren yet leave the vehicle fully armed and protected. This feature is
particularity useful if you are aware of children playing near your vehicle that may accidently
trigger your security system. In this case you can cancel the siren sounding
INTRUSIONWARNINGSIGNAL:
This system will inform you if an intrusion attempt has occurred while you were away from
the vehicle. Upon disarm, the siren will chirp 4 times and the parking lights will flash 3 times.
Enter the vehicle and before turning on the ignition switch, observe the LED flash pattern.
If the LED flashes one time...pause, one time...pause etc., then an intrusion attempt was
made by impact or a strong vibration that the shock sensor detected. Check the vehicle for
possible damage to the glass or body panels.
If the LED flashes two times...pause, two times...pause etc., then an intrusion attempt was
made to open the hood, trunk, or by an accessory triggering device. Check the vehicle for
indications of forced entry to these openings.
If the LED flashes three times...pause, three times...pause etc., then an intrusion attempt was
made to the vehicle doors. Check all doors for indications of forced entry.
Note: The LED intrusion warning indications are stored in the system's memory and will be
erased when the ignition switch is turned on.
VALET SWITCH:
The valet switch allows you to temporarily bypass all alarm functions, eliminating the need to
hand your transmitter to parking attendants or garage mechanics. When the system is in valet
mode, all alarm functions are bypassed, however the remote panic feature and remote door
locks will remain operational. To use the valet mode, the system must first be disarmed either
by using your keychain transmitter, or by activating your personalized manual override code.
1. Enter the vehicle, and turn the ignition key to the on position.
2. Press and hold the valet pushbutton switch until the dash mounted L.E.D. turns
on solid. The system will remain in the valet mode.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
3. To return to normal operation, press and release the pushbutton switch any time
the ignition is on.
NOTE: Always remember to return the vehicle to the valet off position. This will ensure that the
vehicle remains protected at all times.
MANUALLYOVERRIDINGYOURSYSTEM:
USING THE VALET SWITCH MANUAL OVERRIDE
Your Security System can be disarmed without the use of the keychain transmitter. This is
necessary, since you will need the ability to operate your vehicle if the transmitter is lost or its
battery fails. If your system has been selected for Valet Switch manual override as indicated
on the last page of this manual, to by-pass the alarm system;
1. Open the vehicle door. The alarm will sound.
2. Turn the ignition key to the on position.
3. Within 5 seconds, press and release the valet pushbutton switch.
The alarm system will stop sounding and enter the (by-passed) mode. You can now start and
operate the vehicle normally.
Typically this override mode is used only if the transmitter has become inoperative.
Programming Your Custom Override Code:
Unlike override switches easily found, and defeated, this security system allows the consumer
to program a personal override code, offering a higher level of security. To take advantage of
this option, programmable feature # 10 must be selected for the Custom Code Option. Consult
your installation center for programming details. The system comes from the factory with a
pre-programmed override code of 11. To change this default override code, do the following:
1. Disarm the system by use of the transmitter, or by use of the emergency override
sequence. Turn the ignition switch to the on position.
2. Within 10 seconds, press and release the valet/override switch, 3 times.
3. Within 10 seconds turn the ignition switch off, on, off, on, off, on.
(The siren or horn will beep and the lights will flash one time.)
4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing and releasing the
pushbutton switch from 1up to 9 times.
5. Within 10 seconds of the last entered 10ths digit, turn the ignition switch off then on.
6. Within 10 seconds, begin to enter your chosen units digit by pressing and releasing the
pushbutton switch from 1 up to 9 times.
7. Finish by turning the ignition switch to the off position.
If the new code was accepted, the unit will report back the newly entered code, by flashing the
LED, first indicating the 10ths digit, pause and then the units digit. The unit will report the new
code three times with a one second pause between each code, then the system will begin
arming. If the LED flash pattern
reports the previously stored code, the new code was not entered correctly. Please repeat
steps 1 through 7 above considering the following.
NOTE: Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0 (Zero),
or no digit entered in any place, units or tenths.
NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for more then 5
seconds during any of the above steps, the unit will revert back to the last successfully
stored code.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Custom Code Programming Example:
To Change the code from the factory pre-assigned code of 11 to “52” you would do the
following:
1. Disarm the system by use of the transmitter, or by use of the emergency override
sequence.
2. Turn the ignition switch to the on position.
3. Within 10 seconds, press and release the valet/override switch, 3 times.
4. Within 10 seconds turn the ignition switch off, on, off, on, off, on.
(The siren or horn will beep and the lights will flash one time.)
5. Within 10 seconds, begin to press and release the push button switch to set the tenths
digit. (As per the example, press and release 5 times to set the tenths digit to 5)
6. Within 10 seconds of the last press of the push-button, turn the ignition switch off then on.
7. Within 10 seconds, begin to press and release the push button switch to set the units digit.
(As per the example, press and release 2 times to set the units digit to 2).
8. Turn the ignition switch to the off position. Immediately observe the LED flash pattern.
You will note the LED flashing five times, pause, and then flash two times, pause. This pattern
will be repeated three times indicating the new code (52) has been accepted and stored in
memory.
NOTE: If after step 7, the LED flashes a code other than what was just entered, this indicates
that the code has not been changed. You will have to repeat steps 1 through 7 above
being certain to note the following:
Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0 (Zero), or no
digit entered in any place, units or tenths.
NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for more then 5
seconds during any of the above steps, the unit will revert back to the last successfully
stored code.
MANUALLYOVERRIDINGYOURSYSTEM:
USINGTHECUSTOMCODEOVERRIDE
Assuming the override code programmed has not been changed, and the default override
code of 11 is in the system's memory.
1) Enter the vehicle and turn the ignition switch to the on position.
Note: The siren will sound.
2) Within 5 seconds, press and release the pushbutton switch 1 time.
3) Within 5 seconds, turn the ignition switch off then on.
4) Within 5 seconds, press and release the pushbutton switch 1 time.
5) Turn the ignition switch off then on and start the vehicle.
Note: If you have changed the programmed override code then substitute your new code
tenths for step 2 above, and units for step 5 above.
ELIMINATING THE NORMAL ARM/DISARM CHIRPS
You can selectively eliminate the normal arm & disarm chirps by holding the transmitter button
slightly longer when arming or disarming. This will prevent the siren chirps for one arm or
disarm cycle. If you find this inconvenient and wish to eliminate these chirps permanently,
1. Turn the ignition switch 'on" then 'off'.
2. Within 10 seconds of turning off the ignition, press and release the valet switch 3 times.
3. If the chirps were on before you started, the siren will emit 2 short chirps indicating that the
chirps are now off. If the chirps were off before you started, the siren will emit one short
chirp indicating that the chirps are now on.
NOTE: Whenever the chirps are by - passed, the 4 chirp intrusion indicator and 3 chirp
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
defective zone indicator will always operate. Since these are important warnings to
you that something has happened, they cannot be eliminated.
REMOTEPANICOPERATION
The Lock or Unlock button on your keychain transmitter also functions as a panic switch for
use in emergency situations. To use remote panic,
1. Press and hold the Lock or Unlock button on the keychain transmitter for 3 or more
seconds. The alarm will immediately sound.
2. To stop the alarm, press and hold the Lock or Unlock button on the transmitter again for 3
seconds. If the button is not pressed, the alarm will automatically stop after 30 seconds.
Also if any transmitter button other than the Lock or Unlock button is pressed and released,
the Panic mode will be turned off immediately. The normal function of this transmitter button
will be suspended during the Panic sounding period.
NOTE: While in the Panic mode, pressing and releasing the Lock, or the Unlock buttons will, if
the option is installed, lock and unlock the doors respectively. While in the panic mode,
anytime the unlock button is pressed, the panic feature will continue for the allotted 30
seconds, however, the security system will be disarmed allowing the vehicle to start.
SAFETY (Red Handled ) CONTROL SWITCH
The control switch allows you to temporarily disable the remote starting function of your
system. For safety, this switch must be turned off for vehicle servicing. To disable the unit,
move the red handled control switch to the off position.
The control switch also allows you to select between 2 hour start up and 4 hour start up when
using the automatic start up timer mode. The factory preset start up time for this mode is every
4 hours. To select between 2 or 4 hour start up timer:
1. Begin with the control switch in the on position
2. Turn the ignition switch on then off
3. Within 10 seconds, move the control switch off, on, off, on (2 switch cycles) to select a 2
hour start timer. After 10 seconds expire, the parking lights will flash and the siren will chirp
2 times confirming that the two hour start cycle is set. Or, within 10 seconds move the
control switch off, on, off, on, off, on, off, on (4 switch cycles) to select a 4 hour start timer.
The parking lights will flash and the siren will chirp 4 times confirming that the 4 hour start
timer is set.
REMOTESTARTINGTHEVEHICLE
The Remote Control Unit WILL NOT start the vehicle if any one of the following conditions
exists:
1. The Vehicle Hood Is Opened.
2. The Gear Selector Is In Any Gear Other Then Park.
3. The Brake Is Depressed.
4. The Safety Control Switch Is In The Off Position.
CAUTION! Be certain that the vehicle is outdoors before using this or any remote vehicle
starting device. A running engine produces dangerous carbon monoxide fumes
which can be harmful or fatal if prolonged exposure occurs. DO NOT remote start
the vehicle if it is garaged.
TO REMOTE START THE VEHICLE:
Press and release the transmitter button with the "Trunk/Key" symbol on it, two times within 2
seconds. The vehicle will start and remain running for the pre-programmed 5, 10, 15, or 20
minutes. As a visual indication, the parking lights will flash or turn on depending on the
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
programming set up by your installation center.
When you arrive at your vehicle, disarm the alarm system by pressing and releasing the
unlock/disarm button of your keychain transmitter. Enter the vehicle and turn the ignition key
to the on position.
CAUTION! Do not turn the key to the start position. This will cause the starter motor to
engage with the already running engine which could result in damage. Step on
the brake pedal to disengage the remote start unit. The vehicle will continue to
run but now on it's own power.
NOTE: The engine will stop running before the expiration of the pre-programmed run timer if
you complete any of the following:
1. Press and release trunk/key button of your keychain transmitter two times within 2 seconds.
2. Depress the brake pedal.
3. Open the hood.
4. Move the red handled control switch to the off position.
5. Race the engine to above 4000 RPM.
OPERATING ON AUTOMATIC START UP TIMER MODE
The system has the ability to automatically start the vehicle every 2 or 4 hours over a 48 hour
period. This feature is especially useful in cold climates where the only means to keep the
engine and engine fluids warm is to periodically start the engine.
CAUTION! Be certain that the vehicle is outdoors before using this or any remote vehicle
starting device. A running engine produces dangerous carbon monoxide fumes
which can be harmful or fatal if prolonged exposure occurs. DO NOT remote
start the vehicle if it is garaged.
TO BEGIN THE AUTOMATIC START UP TIMER
1. Turn the ignition key on then off.
2. Within 10 seconds, activate the RF start command two times. (Push the trunk/key button
of your keychain transmitter 4 times).
The parking lights will flash and the siren will chirp 4 times indicating the timed start mode is
activated.
The vehicle, on a 2 or 4 hour interval basis, will automatically start, run for the pre-pro-
grammed time (5,10, 15 or 20 minutes), and then shut off. This will continue for 48 hours.
NOTE: The automatic start up timer can also be initiated from the keychain transmitter.
To do this:
1. Start the vehicle using the keychain transmitter by pressing and releasing the trunk/key
button 2 times.
2. Shut off the vehicle using the keychain transmitter by pressing and releasing the trunk/key
button 2 times.
3. Within 10 seconds of step 2, activate the RF start command two times. (Push the trunk/key
button of your keychain transmitter 4 times).
The parking lights will flash and the siren will chirp 4 times indicating the timed start mode is
activated.
CANCELING THE AUTOMATIC START UP TIMER
To cancel the automatic start up timer do one of the following;
1. Start the vehicle manually with the use of the ignition key and depress the brake pedal.
2. Remote start the vehicle using your keychain RF transmitter.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTIONAL DEVICE OUTPUT ( CHANNEL 3 )
Controlled By: o Option Button, o trunk/key button, o Both Option & Lock Button,
or o Both Option and Unlock Button.
This security system is equipped with an output which will activate when the appropriate
transmitter button is depressed for 4 seconds. Optional devices that may be connected to this
channel are;
oRemote Window Closure
oRemote Garage Door Interface
o2nd Vehicle Equipped With Similar Audiovox Products
If your vehicle is not equipped with an electronic trunk release switch, or other option listed,
this feature may have been connected to another accessory. Please ask your dealer for
further information.
NOTE: The feature that has been added to channel 3 will always be operated using the same
transmitter button that controls the remote start unit. There is no way to move the
channel 3 function to a different channel.
ADDITIONAL REMOTE FUNCTION ( CHANNEL 4 )
Controlled By: o Option Button, o trunk/key button, o Both Option & Lock Button,
or o Both Option and Unlock Button.
This security system has an additional feature that can be connected to a number of different
optional accessories. Some of the more common uses for this channel are;
oRemote Window Closure
oRemote Garage Door Interface
o2nd Vehicle Equipped With Similar Audiovox Products
To operate the accessory associated with channel 4, press and release the channel 4
button(s) of your keychain transmitter. Note: The channel 4 output will remain active for as
long as the transmitter button(s) are held. Certain accessories may take advantage of the
extended output capability of this channel. Check with your installation center for operation of
the accessory that may be connected to channel 4.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
PRO-9675FT4
SYSTEM FUNCTIONS AT A GLANCE
ALARM DASH LED INDICATORS
RAPID FLASHING
SLOW FLASHING
OFF
=
=
=
=
=
=
=
PASSIVE ARMING
ARMED
DISARMED
ON SOLID
VALET MODE
3 FLASH... PAUSE
2 FLASH...PAUSE
1 FLASH...PAUSE
INTRUSION ZONE 3
INTRUSION ZONE 2
INTRUSION ZONE 1
ALARM SIREN CHIRP INDICATION
1 CHIRP*
2 CHIRPS*
3 CHIRPS
4 CHIRPS
5 CONTINUOUS
=
=
=
=
=
ARM
DISARMED
ARMING WITH ENTRY POINT OPENED
DISARM AFTER INTRUSION
TRIGGERED/PANIC
ALARM PARKING LAMP INDICATIONS
1 FLASH
2 FLASH
3 FLASH
CONTINUOUS FLASH
=
=
=
=
ARM
DISARM
DISARM AFTER INTRUSION
TRIGGERED/PANIC
REMOTE START SIREN INDICATIONS
1 LONG/1SHORT
=
RF START COMMAND ISSUED
(IF SELECTED ON)
REMOTE START PARKING LAMP INDICATIONS
1 FLASH
ON
=
=
RF START COMMAND ISSUED
RUNNING UNDER REMOTE START
CONTROL (IF SELECTED)
CONTINUOUS FLASH
=
RUNNING UNDER REMOTE START
CONTROL (IF SELECTED)
© 2000 Audiovox Electronics Corporation, Hauppauge, NY 11788
128-5869
Download from Www.Somanuals.com. All Manuals Search And Download.
|