Audiovox Automobile Alarm APS25CH User Manual

Model APS-25CH  
Installation Manual  
Note : When both Passive Arming and Voltage Sensing are selected, you must hardwire the driver’s door pin switch  
in order to begin the passive arming sequence.  
RF Programmable Features :  
Feature Selection  
1 Chirp  
2 Chirps  
3.5 Sec.  
3 Chirps  
4 Chirps  
Default  
1 Sec.  
1st Door L/UL  
1 Sec.  
1 Sec L, Dbl. U/L  
2nd Accy Lock  
Auto Lock On  
Auto UL On  
Passive  
Auto Lock Off  
Auto UL Off  
Active  
Auto Lock Off  
Auto UL Off  
Active  
3rd Accy. UL  
4th Passive Locks  
5th Passive/Active Arm  
6th Voltage Sense  
Passive Arm  
Voltage Sense  
Active Arm  
Hardwire  
Active Arm  
Hardwire  
To program these selectable features;  
Action  
System Response  
1 Chirp - LED 1 flash  
Turn ignition on No response  
Press and release the valet switch 3 times  
Within 3 seconds, turn ignition Off  
Then On  
Press transmitter Lock button to change  
Press transmitter Lock button to change  
or  
Short chirp, then long chirp  
1 chirp = 1 second door locks  
2 chirps = 3.5 second door locks  
First  
3 chirps = 1 sec. lock, dbl 1 sec. unlock  
Second  
Third  
Press and release the valet switch  
Press transmitter Lock button to change  
or  
Press and release the valet switch  
Press transmitter Lock button to change  
or  
2 chirps = auto locks off  
1 chirp = auto locks on  
2 chirps = auto unlock off  
1 chirp = auto unlock on.  
Fourth  
Fifth  
Press and release the valet switch  
Press transmitter Lock button to change  
or  
Press and release the valet switch  
Press transmitter Lock button to change  
or  
2 chirps = active locks  
1 chirp = passive locks  
2 chirps = active arming  
1 chirp = passive arming  
Sixth  
Press and release the valet switch  
Press transmitter Lock button to change  
or  
2 chirps = hardwire  
1 chirp = voltage sense  
Turn ignition key off  
Exit program mode  
Note: Once you enter the feature programming mode, do not allow more than 30 seconds to pass between steps, or the  
programming will be terminated.  
128-6453  
1 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VALETSWITCH:  
Select a desired mounting location for the switch, that is easily accessible to the driver of the vehicle.  
The switch does not have to be concealed, however, concealing the switch is always recommended, as this  
providesanevenhigherlevelofsecuritytothevehicle.Theswitchmaybemountedinorbelowthedashbydrilling  
a 1/4" diameter hole in the location. Be sure to check behind the dash for adequate clearance for the body of  
theswitch, andtoconfirmthatthedrillwillnotdamageanyexistingcomponentsasitpassesthroughthedash.  
Routetheconnectorandwirestowardthemoduleandplugtheconnectorintotheappropriateconnectoronthe  
module.  
WIRING THE SYSTEM:  
WHITE WIRE: + 12 VDC PULSED PARKING LIGHT OUTPUT ( 15 A MAX )  
This wire is provided to flash the vehicle’s parking lights. Connect the white wire to the positive side of one of  
the vehicle’s parking lights.  
REDFUSEDWIRE-(VOLTAGESENSING):+12VDCCONSTANTBATTERYSOURCE  
This wire controls the sensitivity of the voltage sensing circuit, which detects the turning on of an interior light  
whenadoorisopened.Itwillalsodetecttheswitchingonofparkingorheadlamps,andinmanycaseswilltrigger  
thealarmwhenathermostaticallycontrolledelectronicradiatorcoolingfanswitcheson. Itisrecommendedthat  
when installing this system into vehicles with electronic “after fans”, the procedure for RED FUSED WIRE -  
(HARDWIRE)shouldbefollowed.  
In voltage sensing applications, the closer to the battery that the red wire is connected, the less sensitive the  
voltage sense circuitry will be. Moving this connection point to the fuse panel will increase the sensitivity and  
connectingtothecourtesylampfuseinthevehiclewillprovidemaximumsensitivityofthevoltagesensecircuit.  
REDFUSEDWIRE-(HARDWIRE):+12VDCCONSTANTBATTERYSOURCE  
Whenhardwiringthecontrolmoduletopinswitchesatallentrypoints,thevoltagesensecircuitmustbedisabled.  
Setprogrammingfeature#6tothe"OFF"position. Connecttheredwiretoa+12VDCconstantbatterysource.  
DARKBLUEWIRE:300mAPULSEDOUTPUT/CHANNEL2  
The dark blue wire pulses to ground via an independent RF channel from the keychain transmitter. This is a  
transistorized, low current output, and should only be used to drive an external relay coil.  
WARNING: Connectingthedarkbluewiretothehighcurrentswitchedoutputoftrunkreleasecircuits  
or some remote starter trigger inputs, will damage the control module.  
Connect the dark blue wire to terminal 86 of the AS-9256 relay (or equivalent 30 A automotive relay) and wire  
the remaining relay contacts to perform the selected function of channel 2.  
WHITEw/BLACKTRACEWIRE:POSITIVEOUTPUTTOSIREN  
Route this wire through a rubber grommet in the firewall to the siren location. Connect the white/black wire to  
the positive wire of the siren. Secure the black ground wire of the siren to chassis ground.  
BLACKWIRE:CHASSISGROUND  
Connect this wire to a solid, metal part of the vehicle’s chassis. Do not confuse this wire with the thin black  
antenna wire that exits the control module independently.  
YELLOWWIRE:+12VDCIGNITIONSOURCE  
Connect this wire to a source that supplies 12 VDC when the ignition key is in the ON and CRANK positions  
and off when the key is in the OFF position.  
Page 3  
128-6453  
3 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DARKGREENWIRE:(-)INSTANTTRIGGER  
This is an instant on ground trigger wire. It must be connected to the previously installed hood and trunk pin  
switches.  
BROWNWIRE:-DOORTRIGGER  
If the vehicle’s door courtesy light switches have a - ground output when the door is opened ( GM and most  
Imports ) you must connect this wire to the negative output from one of the door switches. In most cases, the  
brown wire will only need to be connected to one door switch, no matter how many doors the vehicle has.  
WARNING: Do not use the brown wire if the vehicle has + 12 Volt output type door switches.  
(see PURPLE WIRE)  
Note for vehicles with interior delay lighting see programming under title "Completing The Installation".  
PURPLEWIRE:+DOORTRIGGER  
If the vehicle’s door courtesy light switches have a + 12 volt output when the door is opened ( most Fords and  
someImports), youmustconnectthiswiretothepositiveoutputfromoneofthedoorswitches. Inmostcases,  
the purple wire will only need to be connected to one door switch, no matter how many doors the vehicle has.  
WARNING: Do not use the purple wire if the vehicle has ground output type door switches.  
(see BROWNWIRE)  
Note for vehicles with interior delay lighting see programming under title "Completing The Installation".  
ORANGEWIRE: GROUNDOUTPUTWHENARMED  
Thiswireisprovidedtocontrolthestartercutrelay.Connecttheorangewiretoterminal86oftherelayandwire  
the remaining relay contacts as shown in the wiring diagram.  
IMPORTANT: Audiovox does not recommend using this relay to interrupt the ignition wire. Only  
connect this relay to the low current starter solenoid feed wire, as indicated on the wiring  
diagram.  
GREY&BLACK2PIN(blue)CONNECTOR:VALETSWITCH  
Ifyouhavenotdonesoalready,routethetwoconductor,blueconnectorfromthepreviouslyinstalledvaletswitch  
to the alarm control module and plug it into the mating blue connector on the end of the module.  
RED&BLUEWIRES:DASHMOUNTEDLED  
Route the two conductor, white connector (red and blue wires) from the previously installed LED to the alarm  
control module and plug it into the mating white connector on the end of the module.  
RED & GREEN 2 PIN (white) CONNECTOR: DOOR LOCK OUTPUTS  
These wires will provide a pulsed ground output to the factory door lock control relay. The maximum current  
draw through these outputs must not exceed 300 mA.  
3 Wire Ground Switched Door Locks  
In this application, the red wire provides a ground pulse during arming (pulsed ground lock) output. Con-  
nect the red wire to the wire that provides a low current ground signal from the factory door lock switch to the  
factory door lock control relay.  
The green wire provides a ground pulse during disarming (pulsed ground unlock) output. Connect the  
green wire to the wire that provides a low current ground signal from the factory door unlock switch to the  
factory door lock control relay.  
Page 4  
128-6453  
4 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 Wire Positive Switched Door Locks  
In this application, the red wire provides a positive pulse during disarming (pulsed + 12 volt unlock) output.  
Connect the red wire to the wire that provides a low current positive signal from the factory door unlock switch  
to the factory door lock control relay.  
The green wire provides a positive pulse during arming (pulsed + 12 volt lock) output. Connect the green  
wire to the wire that provides a low current positive signal from the factory door lock switch to the factory door  
lock control relay.  
Resistive Circuits, As Well As 4 Wire Polarity Reversal and 5 Wire Alternating 12 Volt Door Lock  
Control Circuits  
These applications require the use of additional components which may include relays, fixed resistors, or for  
convenience, the AS 9159 Door Lock Interface. Refer to the AUDIOVOX Door Lock Wiring Supplement and or  
the Audiovox fax back service for information on your particular vehicle for properly connecting to these types  
of circuits.  
COMPLETING THE INSTALLATION  
NOTE: This unit has the ability to learn the dome light delay time, up to 60 seconds. If the vehicle has delay  
interior lights, and you wish to avoid three chirp, defect zone, indication normally associated with this type of  
interior light, we suggest you learn the interior light delay.  
To learn the light delay, start with all doors closed:  
(1) Use the transmitter to Lock / Unlock / Lock / Unlock / Lock / Unlock / Lock, the system.  
The LED turns on solid to confirm the system entered the learn mode.  
(2) Immediately open and close the door of the vehicle to initiate the dome delay.  
The unit will monitor the door trigger input Positive, (Purple), and Negative, (Brown) when active.  
When the dome light turns off, the unit will add 2 seconds then exit the learn mode.  
(3) The LED will begin flashing the Armed indication indicating the unit has exited the learn mode and is  
armed  
Antenna Wire : Be sure to extend the thin black antenna wire to it’s full length and cable tie into place where  
it cannot be damaged. Avoid wrapping this wire around major, high current wire looms.  
Adjusting the Shock Sensor : The sensitivity of the pre - detect circuit, where used, is automatically set 30%  
less sensitive than the full trigger circuit.  
Using a small screwdriver, gently turn the adjustment screw fully counterclockwise. ( DO NOT over turn this  
screw. Maximum rotation for this adjustment is 270° ). Close the hood and trunk lids, and arm the alarm. Wait  
6 seconds for the accessories trigger zone to stabilize, then firmly strike the rear bumper with the side of a  
closed fist considering the amount of force required to break a window.  
CAUTION : Never perform this test on the vehicle’s glass, as you may break the window.  
Turn the adjustment screw clockwise ( increasing sensitivity ) about ¼ turn and re-test. Repeat this  
procedure until the alarm sounds. Ultimately, one firm strike to the rear bumper will cause the alarm to emit  
pre - detect warning tones.  
WARNING ! Setting the sensitivity too high can cause false alarms due to noise vibrations from passing  
trucks and heavy equipment. To decrease sensitivity, turn the adjustment screw counter clockwise.  
Wire Dressing : Always wrap the alarm wires in convoluted tubing, or with a spiral wrap of electrical tape.  
Secure these looms along the routing using cable ties. This will ensure that the alarm wires are not damaged  
by falling onto hot or sharp moving surfaces in the vehicle.  
Operation :  
Take a few moments to check off the appropriate option boxes in the owner’s manual and to  
fully explain the operation of the system to your customer.  
Place the Valet Switch Tag and or the Remote Start Control Switch Tag on their respective  
switches and point these out to the customer.  
Page 5  
128-6453  
5 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
THISPAGELEFTBLANKINTENTIONALLY  
128-6453  
6 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
128-6453  
7 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
© 2003 Audiovox Electronic Corporation, 150 Marcus Blvd., Hauppauge, N.Y. 11788  
128-6453  
128-6453  
8 of 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  

3Com Network Card ISDN Modem User Manual
Acoustic Energy Speaker Linear One User Manual
Adcom Stereo Amplifier GFP 750 User Manual
Air King Vacuum Cleaner CVS 22E User Manual
AMC CD Player CD8b User Manual
American Standard Hot Tub 7242XXXW User Manual
American Standard Outdoor Shower 2555050 User Manual
Apple MP3 Player MC751LL A User Manual
ATON Universal Remote DLA2RM User Manual
Azden Microphone 221R User Manual