About the Apple Ethernet CS II Card
The Apple Ethernet CS II Card expands the
communication capabilities of models of Macintosh
computers that have a communication slot II (CS II).
The card is designed for networks that conform to the
IEEE 802.3 standard for Ethernet.
What’s in the box
m One Apple Ethernet CS II Card with either a
twisted-pair connector, a thin coaxial connector
(with T-connector attached), or an AAUI connector
Note: Keep the card inside its antistatic bag in
the protective cardboard box until you’re ready
to install it.
There are three configurations of the Apple Ethernet
CS II Card, each with a connector for a different type
of Ethernet cable. These are
m twisted pair
m thin coaxial (“coax”)
m One floppy disk containing Ethernet CS II
software
m Warranty card
m AAUI (universal connector)
m User’s guide
This manual provides instructions for all three
configurations of the card.
IMPORTANT If you purchased a new Macintosh and
this booklet came in the box, your Apple Ethernet
CS II Card and software may already be installed,
and no disk containing the Ethernet CS II software
is included. Skip ahead to “Installing Your
Ethernet Software” for information about setting
up your software.
You begin by installing the card and then connecting
it to your network. You should also install the latest
version of the Ethernet software if a disk is included
with the card.
The Apple Ethernet CS II Card requires System
7.5.3 or a later version. For best performance your
system should have 8 megabytes (MB) minimum of
random-access memory (RAM).
1
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT If you’re installing the Apple Ethernet
CS II Thin Coax Card, a T-connector is connected to
your card. Before you install the card, twist the
T-connector to unlock it from your card and set
it aside.
5. Align the card over the communications slot and
press down firmly and evenly on both ends until the
card fits snugly into place.
You can test to see if the card is properly
connected by lifting the card slightly. If it resists
and stays in place, it’s connected.
4. Tilt the card to fit the connector through the back
panel’s opening and hook the small metal bracket at
the top of the card to the edge of the opening.
6. Follow the directions that came with your computer to
replace the back panel or lid and reattach any cables
you removed earlier.
This procedure depends on the model you have.
Metal bracket
Handle the card by its edge.
Push down evenly and firmly.
T-connector
removed from the
Thin Coax card
To locate the
communication slot for
your computer, see the
setup instructions that
came with your Macintosh.
Port on the Thin Coax card
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your Card to the Network
To connect your card to the network, follow the
instructions for your specific card. Check the
illustration below to determine your card type.
Connecting an Apple Ethernet CS II
Twisted Pair Card
1. Plug the twisted-pair cable from your network into the
RJ-45 port on your card.
Just as with a telephone wire connector, you’ll
hear a “click” when you plug in the cable.
Card’s green LED lights
up when there’s a good
network connection.
CS II Thin
Coax Card
CS II Twisted-
Pair Card
CS II AAUI
Card
Other end of cable
connects to network
controller (hub).
Refer to the following pages for instructions on how
to connect your card:
m Apple Ethernet CS II Twisted Pair Card: page 4
m Apple Ethernet CS II Coax Card: page 5
m Apple Ethernet CS II AAUI Card: page 7
RJ-45 connector clicks when
you attach it to the port.
2. Turn on the computer’s power switch and start up the
computer.
You’ve made the hardware connections. Turn to
“Installing Your Ethernet Software” later in this
booklet for software installation instructions.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
2. On the computer closest to your computer, detach the
network cable (or terminator) from the T-connector.
Connecting an Apple Ethernet CS II
Coax Card
This disrupts network services for other users.
IMPORTANT Connecting your computer to the
network will temporarily disrupt services to other
users, so work quickly. To minimize the disruption,
alert your network administrator before continuing
these instructions.
Note: You can add a computer in the middle or at
either end of the network.
3. Lock the free end of the new cable to the
T-connector on the other computer.
4. If you are adding your computer somewhere in the
middle of the network, lock the unattached network
cable to your T-connector. Otherwise, lock a
terminator to your T-connector.
1. Attach one end of the new cable for your computer to
the T-connector you removed from your card.
Be sure to twist and lock the cable’s connector to
your T-connector.
This restores network services for other users.
When you add your Thin Coax Card, you must
use a T-connector in one of these two ways:
Lock a terminator to
a T-connector at
the end of the network.
Twist to lock both cables
to a T-connector in the
middle of the network.
Network
continues
5
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Attach your T-connector to the port on your card.
6. Turn on your computer’s power switch and start up
the computer.
It may help to use two hands. With one hand,
push the T-connector on the port. While still
holding the T-connector, use the fingers on your
other hand to lock the connector into place.
You’ve made all the necessary hardware
connections. Next you’ll install and set up your
network communication software. For
instructions, turn to “Installing Your Ethernet
Software” later in this booklet.
Pull the T-connector to test that it is locked
securely to the port.
Port on card
The T-connector locks
the network cable
(and terminator, if
needed) to your card.
Cable from one
side of network
Cable from other
side of network
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Turn on the computer’s power switch and start up the
computer.
Connecting an Apple Ethernet CS II
AAUI Card
You’ve made all the necessary hardware
connections. Next you’ll install and set up your
network communication software. For
instructions, turn to “Installing Your Ethernet
Software” later in this booklet.
1. Plug the AAUI connector from your network
transceiver cable into the AAUI port on your card.
You need a specific AAUI-compatible transceiver
for the kind of media used for your network: thick
coax, twisted-pair, thin coax, fiber-optic, or
twisted-pair hub. The transceiver connects your
computer to the main network cable.
The AAUI connector
attaches to the card’s port.
The cable also connects to the
appropriate AAUI-compatible
transceiver for your network.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Your Software
If you purchased a new Macintosh with an Apple
Ethernet CS II card, you may already have the
required software installed.
Installing the Ethernet software
To install the latest version of Ethernet software
you need to use the Installer program on the PCI
Network Installer disk, included with your card.
If a PCI Network Installer disk is included with your
card, perform the steps in “Installing the Software,”
next.
For safety, make sure that the Installer disk is locked
before you use it. To lock a disk, slide the tab on the
back side so that the square hole is open.
If no PCI Network Installer disk is included with
your card, the latest software is already installed.
Skip ahead to “Setting the Network Software
Selector.”
Keep the Installer disk after installation in case you
need to reinstall Ethernet software some time in
the future.
Close all open applications before installing.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
To install Ethernet software:
3. Make sure that the disk indicated in the Installer’s
dialog box is your current startup disk. Then
click Install.
1. Insert the PCI Network Installer disk in your
Macintosh and double-click the disk’s icon to open it.
If you see a message indicating that the software
cannot be installed while other programs are
running, click Continue.
The Apple Ethernet CS II cards require the
versions of software supplied on the PCI Network
Installer disk.
4. When you see a message reporting that the
installation was successful, click Restart.
2. Open the Installer program, review the Welcome
screen, and click Continue.
Before you can use services on an Ethernet
network, you need to specify that you’re using an
Open Transport network configuration. You then
set two control panels for Ethernet networking.
The next section shows how.
The Easy Install dialog box appears.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Click “Use Open Transport Networking” button to
select it, if necessary.
Setting the Network Software Selector
To use your Apple Ethernet CS II card, you must set
your computer to use Open Transport Networking,
which provides advanced networking services and
compatibility. You use the Network Software
Selector application to select Open Transport
Networking.
For more information about Open Transport, see the
“Networks” topic area of the Macintosh Guide,
available in the Guide (h) menu.
Follow these steps:
1. Open the Apple Extras folder.
4. Choose Quit from the File menu.
2. Double-click the Network Software Selector
application to open it.
If you changed the selected option in the Network
Software Selector, you must now restart your
computer to have your changes take effect. If
Open Transport was already selected, you don’t
need to restart.
5. Choose Restart from the Special menu, if necessary.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Choose Ethernet from the pop-up menu.
Setting your control panels for Ethernet
(You may have different network-connection
choices from those shown in the figure.)
You must next set the AppleTalk and TCP/IP control
panels for Ethernet.
Setting the AppleTalk control panel
A Macintosh computer’s AppleTalk network
connection is preset for LocalTalk connected to
either the printer port or the modem port. To connect
to an Ethernet network using AppleTalk, you need to
change the setting in the AppleTalk control panel.
Follow these steps:
1. Choose Control Panels from the Apple (
K) menu.
2. Double-click the AppleTalk control panel to open it.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
4. If you see a pop-up menu that lists zones, select the
zone you want.
6. Close the AppleTalk control panel.
A dialog box asks you to confirm your changes.
7. Click Save to save the changes you made in the
AppleTalk connection.
You are now ready to use AppleTalk services
available on your Ethernet network.
For Apple Ethernet CS II Twisted Pair and Coax
Cards only:
If your network has been set up to allow you to
choose a zone but you have not yet done so, the
menu lists choices, with your designated zone
selected. The zone you select determines the
default location for any network services
provided by your computer and listed in the
Chooser (such as file sharing). Before you select
a zone different from the one already highlighted,
consult your network administrator.
8. Check that the LED light on the card (above the port)
indicates that the card is working properly.
Twisted Pair Card: The light is pale green when the
connection is good. The green light blinks brightly
when data is being transmitted from the card.
Coax Card: The light is pale green when the card
is selected in either the AppleTalk or the TCP/IP
control panel. The green light blinks brightly
when data is being transmitted from the card.
5. Make any changes you want to the AppleTalk
address.
Consult your network administrator if you need
assistance with this information.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Consult your network administrator if you need
assistance with this information.
Setting the TCP/IP control panel for Ethernet
If you want to connect to an Ethernet network using
TCP/IP network protocols, you need to change the
setting in the TCP/IP control panel.
5. Close the TCP/IP control panel.
A dialog box asks you to confirm your changes.
Follow these steps:
6. Click Save to save the changes you made in the
TCP/IP connection.
1. Choose Control Panels from the Apple (
K) menu.
You are now ready to use TCP/IP services
available on your Ethernet network.
2. Double-click the TCP/IP control panel to open it.
For Apple Ethernet CS II Twisted Pair and Coax
Cards only:
7. Check that the LED light on the card (above the port)
indicates that the card is working properly.
3. Choose Ethernet from the pop-up menu.
Twisted Pair Card: The light is pale green when the
connection is good. The green light blinks brightly
when data is being transmitted from the card.
(You may have different network-connection
choices from those shown in the figure.)
Coax Card: The light is pale green when the card
is selected in either the TCP/IP or the AppleTalk
control panel. The green light blinks brightly
when data is being transmitted from the card.
You’ve now completed setting up your Apple
Ethernet CS II software for networking.
4. Make any changes you want to the configuration or
the IP address.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Disconnecting and Moving Your Computer
To disconnect your computer from the network, shut
down your system and unplug the network cable’s
connector from the port on the Ethernet card. Do not
disconnect the network cable or terminator.
If you plan to move your computer and reconnect to
the network at a new location, notify your network
administrator before you move.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Following are guidelines for handling common
problems. If these suggestions don’t help you fix the
problem, contact your network administrator.
If the AppleTalk or TCP/IP control panel icon is missing:
The AppleTalk or TCP/IP control panel may have
been moved from the Control Panels folder. Look
for it on your hard disk, drag it to the Control Panels
folder, and restart your Macintosh.
Also check to see whether your software is set to use
Open Transport networking. See the instructions in
“Setting the Network Software Selector.”
IMPORTANT The first step in troubleshooting any
problem with your network connection is to check
each of the following items.
m The computer’s power is on.
m The card is installed correctly.
m The Ethernet cable’s connector is securely
fastened to your card.
m The network cable is in good condition and
locked to the connector.
Your Ethernet software may not have been installed
properly. If you can’t find the AppleTalk or TCP/IP
control panel, you’ll need to reinstall the network
software according to the instructions in this guide.
m If your card is configured for a thin coax cable
and your computer is on either end of the
network, be sure that a terminator is locked to the
T-connector.
m Your Ethernet network is working properly—no
one else is having problems with the network.
If Ethernet doesn’t appear in the AppleTalk or TCP/IP
control panel:
Make sure that you have installed your Apple
Ethernet CS II card in your communications slot II.
Also, there may have been a problem with the
network software installation. Reinstall your
network software according to the instructions in
this guide.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
If you can’t select Ethernet in the AppleTalk or TCP/IP
control panel:
If you don’t see network services listed in the Chooser:
Make sure your network connection is set correctly.
Open the AppleTalk control panel and choose
Ethernet. (If the Chooser is open, close and reopen it
to update its information.)
You can only select Ethernet when the network
cable is installed properly and the network is
operating correctly. Be sure that the network cable is
properly attached. If you are still unable to select
Ethernet, there may have been a problem with the
network software installation. Reinstall your
network software according to the instructions in
this booklet.
On the Apple Ethernet CSII Twisted Pair Card, the
external LED will light when a proper network
connection is established. If the LED doesn’t
light,the network is not responding to the card. See
your network administrator.
On the Apple Ethernet CS II Twisted Pair Card, the
external LED will light when a proper network
connection is established. If the LED doesn’t light,
the network is not responding to your card. See you
network administrator for help.
If you can access some services but can’t access a
particular service (printing, for example), the device
providing that service might be located in a different
AppleTalk zone, or it might be malfunctioning,
switched off, or disconnected from the network.
There may also be a break somewhere in the
network cables between your Macintosh and the
missing service.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
If your system can’t load Ethernet at startup and
reverts to LocalTalk:
If your card is defective or you have a problem with the
installation and your network administrator cannot help:
Your System file may be damaged or your Ethernet
installation was unsuccessful. Try reinstalling the
network software. Also check that your network
cable is properly attached and terminated, if
In the United States, contact the Apple Assistance
Center at 800-SOS-APPL. In Canada, call
1-800-263-3394. Outside the United States and
Canada, contact your local Apple-authorized
reseller.
necessary. Check that your card is properly installed.
If the system won’t let you change the
network connection:
You may be using essential services (such as file
sharing) or applications that might prohibit the
change. Quit the service named in the system’s alert
message and try changing the network connection
again. You can also try quitting all application
programs. If this doesn’t work, and it’s all right for
you to disrupt services, shut down your Macintosh
using the Shut Down command. Restart the
computer, change the network connection, and start
the service or application again.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Apple Ethernet CS II Thin Coax Card
Apple Ethernet CS II Twisted-Pair Card
Connector
Cable
Ethernet IEEE 802.3– compliant BNC port
Connector
Ethernet 10BASE-T– compliant
RJ-45 port
RG-58/U; 2-meter minimum
length between devices
Recommended
cable
Category 3, 26 gauge; 100 meters from
card to hub, maximum
Terminator
50 ohm, BNC-type
Ethernet transmit/ 10 megabits per second data rate
receive maximum
Ethernet transmit/ 10 megabits per second maximum
receive data rate
Power dissipation Less than 1.25 watts, with an average of
Power dissipation Less than 2.5 watts, with an average of
.9 watt
2.25 watts
Environmental
requirements
Operating temperature: 50˚ to 104˚ F (10˚
to 40˚ C)
Environmental
requirements
Operating temperature: 50˚ to 104˚ F
(10˚ to 40˚ C)
Humidity: 20% to 95% noncondensing
Humidity: 20% to 95% noncondensing
Ethernet controller Digital Semiconductor DECchip 21041
Ethernet controller Digital Semiconductor DECchip 21041
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Apple Ethernet CS II AAUI Card
Connector
Ethernet IEEE 802.3– compatible AAUI port
Ethernet transmit/ 10 megabits per second data
receive
rate maximum
Power dissipation Less than .9 watts, with an average of
.75 watt (plus transceiver power dissipation.)
Environmental
requirements
Operating temperature: 50˚ to 104˚ F
(10˚ to 40˚ C)
Humidity: 20% to 95% noncondensing
Ethernet controller Digital Semiconductor DECchip 21041
19
Download from Www.Somanuals.com. All Manuals Search And Download.
For More Information
The following books from Apple Computer,
published by Addison-Wesley, are available at
computer bookstores.
Planning and Managing AppleTalk Networks
provides comprehensive information on setting
up, maintaining, and troubleshooting small- to
medium-sized AppleTalk networks.
Inside AppleTalk, second edition, is the definitive
technical guide to the protocol architecture of the
AppleTalk network system.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Apple
EthernetCSIICard
User’sGuide
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC statement for Apple Ethernet CS II Thin Coax Card
The equipment described in this manual generates and uses radio-
frequency energy. If it is not installed and used properly—that is, in strict
accordance with Apple’s instructions—it may cause interference with
radio and television reception.
m
Install a rooftop television antenna with a coaxial cable lead-in
between the antenna and the television.
If necessary, consult an Apple-authorized service provider or Apple
for assistance. See the service and support information that came
with your Apple product. Or contact an experienced radio-television
technician for additional suggestions. You may find helpful the
following booklet, prepared by the FCC: Interference Handbook (stock
number 004-000-00493-1). This booklet is available from the U.S.
Government Printing Office, Washington, DC 20402.
This equipment has been tested and found to comply with the limits for a
Class B digital device pursuant to the specifications in Part 15 of Federal
Communications Commission (FCC) rules. These limits are designed to
provide reasonable protection against such interference in a residential
installation. However, there is no guarantee that the interference will not
occur in a particular installation.
IMPORTANT Changes or modifications to this product not authorized by
Apple Computer, Inc., could void the FCC certification and negate your
authority to operate the product. This product was tested for FCC
compliance under conditions that included the use of shielded cables and
connectors between system components. It is important that you use
shielded cables and connectors to reduce the possibility of causing
interference to radios, television sets, and other electronic devices. For
Apple peripheral devices, you can obtain the proper shielded cables
through an Apple-authorized dealer. For non-Apple peripheral devices,
contact the manufacturer or dealer for assistance.
You can determine whether your computer is causing interference by
turning it off. If the interference stops, it was probably caused by the
computer or one of the peripheral devices.
If your computer system does cause interference to radio or television
reception, try to correct the interference by using one or more of the
following measures:
m
m
m
m
Turn the television or radio antenna until the interference stops.
Move the computer to one side or the other of the television or radio.
Move the computer farther away from the television or radio.
Plug the computer into an outlet that is on a different circuit from the
television or radio. (That is, make certain the computer and the
television or radio are on circuits controlled by different circuit
breakers or fuses.)
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Industry Canada
VCCI statement
DOC Class B Compliance
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the radio interference
regulations of the Canadian Department of Communications.
Observation des normes—Classe B
Le présent appareil numérique n’émet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de la Classe
B prescrites dans les règlements sur le brouillage radioélectrique édictés
par le Ministère des Communications du Canada.
EU statement
This equipment generates, uses, and may radiate radio-frequency
energy and, if not properly installed and used in accordance with the
instruction manual, may result in interference to radio communications.
This equipment has been designed, tested, and found compliant with the
Class A limits for Information Technology Equipment of EN55022. These
limits are designed to provide reasonable protection against radio
interference when the equipment is operated in a commercial
environment.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC statement for Apple Ethernet CS II Twisted-Pair Card and Apple Ethernet CS II AAUI Card
This equipment has been tested and found to comply with the limits for a
Class A digital device pursuant to Part 15 of the Federal Communications
Commission (FCC) rules. These limits are designed to provide
VCCI statement
reasonable protection against such interference when the equipment is
operated in a commercial environment. This equipment generates, uses,
and can radiate radio-frequency energy and, if not installed and used in
accordance with the instructions in this manual, may cause interference
to radio communications. Operation of this equipment in a residential
area is likely to cause interference, in which case the user, at the user’s
own expense, will be required to correct the interference.
IMPORTANT Changes or modifications to this product are not
authorized by Apple Computer, Inc., and could void the FCC certification
and negate your authority to operate the product. This product was
tested for FCC compliance under conditions that included the use of
shielded cables and connectors between system components. It is
important that you use shielded cables and connectors to reduce the
possibility of causing interference to radios, television sets, and other
electronic devices. For Apple peripheral devices, you can obtain the
proper shielded cables through an Apple-authorized dealer. For non-
Apple peripheral devices, contact the manufacturer or dealer for
assistance.
EU statement
This equipment generates, uses, and may radiate radio-frequency
energy and, if not properly installed and used in accordance with the
instruction manual, may result in interference to radio communications.
This equipment has been designed, tested, and found compliant with the
Class A limits for Information Technology Equipment of EN55022. These
limits are designed to provide reasonable protection against radio
interference when the equipment is operated in a commercial
environment.
Industry Canada
DOC Class A Compliance
This class A digital device meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du
Réglement sur le matériel brouilleur du Canada.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
This manual is copyrighted by Apple or by Apple’s suppliers, with all
rights reserved. Under the copyright laws, this manual may not be
copied, in whole or in part, without the written consent of Apple
Computer, Inc. This exception does not allow copies to be made for
others, whether or not sold, but all of the material purchased may be
sold, given, or lent to another person. Under the law, copying includes
translating into another language.
About the Apple Ethernet CS II Card
1
What’s in the box
1
Installing your Apple Ethernet CS II Card
Connecting your card to the network
Connecting an Apple Ethernet CS II Twisted Pair Card
2
4
4
The Apple logo is a registered trademark of Apple Computer, Inc. Use of
the “keyboard” Apple logo (Option-Shift-K) for commercial purposes
without the prior written consent of Apple may constitute trademark
infringement and unfair competition in violation of federal and state laws.
Connecting an Apple Ethernet CS II Coax Card
Connecting an Apple Ethernet CS II AAUI Card
5
7
Installing your software
8
Every effort has been made to ensure that the information in this manual
is accurate. Apple is not responsible for printing or clerical errors.
Installing the Ethernet software
8
Setting the Network Software Selector
Setting your control panels for Ethernet
10
11
©
1996 Apple Computer, Inc.
1 Infinite Loop
Cupertino, CA 95014-2084
(408) 996-1010
Disconnecting and moving your computer 14
Troubleshooting 15
Apple, the Apple logo, AppleTalk, EtherTalk, LocalTalk, and Macintosh
are trademarks of Apple Computer, Inc., registered in the United States
and other countries.
Specifications 18
Simultaneously published in the United States and Canada.
For more information 20
Mention of third-party products is for informational purposes only and
constitutes neither an endorsement nor a recommendation. Apple
assumes no responsibility with regard to the performance or use of
these products.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
|