American Standard Plumbing Product 4453 User Manual

Installation  
Instructions  
4453 SERIES  
ELITE  
4454 SERIES  
SINGLE CONTROL KITCHEN FAUCET  
and HAND SPRAY  
Thank you for selecting American-Standard...  
the benchmark of fine quality for over 100 years.  
To ensure that your installation proceeds smoothly--  
please read these instructions carefully before you begin.  
Certified to comply with ANSI A112.18.1M  
M968202 REV.1.2  
TOOLS REQUIRED  
Phillips Screwdriver  
Regular Screwdriver  
Channel Locks  
Adjustable Wrench  
Plumbers' Putty or Caulking  
CARE:  
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.  
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A  
CLOTH WITH A COARSE SURFACE.  
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON  
Turn off hot and cold water  
1
CAUTION  
supplies before beginning.  
(A) Installation with ESCUTCHEON (1). Apply a bead of putty to bottom edge of ESCUTCHEON WITH PUTTY PLATE (1).  
Insert supply HOSES (3) and SHANK (4) through hole of ESCUTCHEON WITH PUTTY PLATE (1) and mounting surface.  
Make certain the SQUARE SEAL RING (2) is properly seated in recess of SPOUT BASE. Follow mounting instructions below  
to secure faucet to mounting surface.  
(B) Installation less ESCUTCHEON (1). Remove ESCUTCHEON WITH PUTTY PLATE (1) and Insert supply HOSES (3) and  
SHANK (4) through mounting hole and seat SPOUT BASE onto sink or mounting surface. Make certain the SQUARE SEAL  
RING (2) is properly seated in recess of SPOUT BASE. Do not use putty.  
Assemble RUBBER WASHER (5), BRASS WASHER (6), and threaded LOCKNUT (7) onto SHANK (4) from underside  
of sink or mounting surface. Hand tighten LOCKNUT (7) and check that rotation of HANDLE (8) from HOT to COLD  
is centered.  
Use a screwdriver to tighten SCREWS (9) on LOCKNUT (7). Work your way around LOCKNUT (7), tightening  
the screws slightly each time until all are snug to ensure even pressure.  
8
B
A
8
SPOUT BASE  
SPOUT BASE  
SQUARE  
SEAL RING  
SQUARE  
SEAL RING  
2
1
2
3
4
PUTTY  
3
9
4
SINK OR  
MOUNTING  
SURFACE  
5
5
6
6
9
7
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
TEST INSTALLED FAUCET  
5
6
Move HANDLE down into "off" position and remove AERATOR.  
Turn on water supplies and check connections for leaks.  
Operate HANDLE up and down, left and right to flush water  
lines thoroughly.  
For faucet with spray, direct SPRAY HEAD into sink and  
activate SPRAY. Check hose connections for leaks.  
AERATOR  
Move HANDLE down to "off" position and replace AERATOR.  
CHECK CONNECTIONS  
FOR LEAKS  
SERVICE  
Reduced flow. If the flow gradually reduces over a number of months, the AERATOR  
may have collected debris. To clean, remove AERATOR and rinse with water and  
remove any debris. Turn on faucet to wash any debris out of the faucet. Thread  
AERATOR back into spout. Operate faucet.  
1
2
3
4
5
Spout leakage. If fitting leaks above or below SPOUT HUB remove SPOUT as follows  
and check SPOUT O-RINGS and SPACER O-RINGS.  
Remove HANDLE BUTTON (2) and loosen SET SCREW (1). Pull HANDLE (3) off valve stem.  
6
Remove CAP (4) and and RETAINER (5). Loosen CARTRIDGE SCREWS (6) and  
remove CARTRIDGE (7).  
7
12  
Pull off SPACER (8) and O-RINGS (9).  
8
9
Remove SPOUT (12) by pulling up gently while moving SPOUT (12) side to side.  
Check both SPOUT O-RINGS (11). Replace if necessary.  
AERATOR  
SPOUT  
HUB  
On models with SPRAYS, DIVERTER (10) can be cleaned by pulling  
DIVERTER (10) out of the MANIFOLD (13). Clean DIVERTER (10) and  
MANIFOLD (13). Push DIVERTER (10) back into MANIFOLD (10).  
11  
Reverse procedure to reinstall SPOUT, CARTRIDGE and HANDLE.  
10  
Clogged CARTRIDGE outlets or inlets may cause reduced flow.  
To clean, first turn off water supply then:  
13  
Remove PLUG BUTTON (2), loosen HANDLE SCREW (1) and remove HANDLE (3).  
Remove ESCUTCHEON CAP (4). unscrew the three CARTRIDGE SCREWS (6).  
Clean inlets of CARTRIDGE (7) and MANIFOLD (13).  
Reassemble CARTRIDGE (7), alternately tightening SCREWS (6). Replace CAP (4) and HANDLE (3). Check flow.  
HOT LIMIT SAFETY STOP ADJUSTMENT  
By restricting handle rotation and limiting the amount of hot water allowed  
"A"  
to mix with the cold, the HOT LIMIT SAFETY STOP reduces risk of accidental  
PRY RED RING FORWARD  
scalding. To set the maximum hot water temperature of your faucets, all you  
need to do is adjust the setting on the HOT LIMIT SAFETY STOP.  
AND ROTATE COUNTER-  
CLOCKWISE ONE C"LAICK"  
TEMPERATURE  
"A"  
Remove HANDLE BUTTON (1) and loosen SET SCREW (2). Pull  
HANDLE (3) off valve stem. Pull off CAP (4). Use a flat blade  
screwdriver or your fingers to pull up and rotate red  
HOT LIMIT SAFETY STOP (5). Follow Step "A" or "B" to adjust  
min./max.discharge temperature. "0" being the hottest to  
"7" the coldest temperature setting. Factory set at "0".  
SET"TBING"NUMBERS  
ADJUSTMENT WHEN  
WATER IS TOO HOT  
PRY RED RING FORWARD  
AND ROTATE CLOCKWISE  
6
5
"B"  
"B"  
ADJUSTMENT WHEN  
WATER IS TOO COLD  
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten  
HANDLE SCREW (1) and install INDEX BUTTON (2).  
"RED RING"- HOT  
LIMIT SAFETY STOP  
M968202 REV.1.2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ELITE  
SINGLE CONTROL KITCHEN  
FAUCET with HAND SPRAY  
MODEL NUMBERS  
023603-0070A  
CARTRIDGE SCREWS  
4453 SERIES  
4454 SERIES  
023529-0070A  
CARTRIDGE  
060343-0070A  
SPACER WITH  
O-RINGS  
060474-YYYOA  
SPOUT KIT  
066070-YYY0A  
AERATOR  
030126-0070A  
BUTTON AND  
SCREW KIT  
060342-YYY0A  
HANDLE KIT  
907468-YYY0A  
ESCUTCHEON CAP  
060366-0070A  
SPOUT SEAL KIT  
921877-0070A  
CAP RETAINER  
042850-0070A  
DIVERTER  
M953667-YYY0A  
HAND SPRAY & HOSE  
Replace the "YYY" with  
appropriate finish code  
CHROME  
002  
099  
208  
295  
060484-YYY0A  
ESCUTCHEON WITH  
SPRAY HOLE  
POLISHED BRASS  
WHITE HEAT  
SATIN NICKEL  
M961773-YYY0A  
SPRAYHOLDER  
(3-HOLE)  
M909320-YYY0A  
SPOUT FLANGE  
923310-0070A  
SPACER  
A911758-0070A  
SQUARE SEAL RING  
060485-YYY0A  
030760-YYY0A  
SPRAY HOLDER  
ESCUTCHEON  
M962146-0070A  
MOUNTING KIT  
HOT LINE FOR HELP  
060341-0070A  
PIPE CAP  
For toll-free information and answers to your questions, call:  
1-800-442-1902  
Weekdays 8:00 a.m. to 6:00 p.m. EST  
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)  
Weekdays 8:00 a.m. to 7:00 p.m. EST  
IN MEXICO 01-800-839-12-00  
Product names listed herein are trademarks of American Standard Inc.  
©
AS America, Inc. 2008  
M968202 REV.1.2  
Download from Www.Somanuals.com. All Manuals Search And Download.  

ADTRAN Switch HTU C M User Manual
AEG Oven E4130 1 User Manual
AEG Washer Dryer 16850 User Manual
Aiphone Intercom System NE NVP 2DC User Manual
Alpine Car Stereo System KCA 420i User Manual
American Standard Plumbing Product 3636STTS User Manual
Atmel Computer Hardware ATmega324PA User Manual
ATN Binoculars Night Vision Binocular User Manual
BC Speakers Speaker 10PLB76 User Manual
Behringer Speaker BB210 User Manual