HAMPTON 5' x 32"™
INTEGRAL APRON WITH
REMOVABLE ACCESS PANEL
HIGH GLOSS ACRYLIC
2425.XXXW-LHO
2425.XXXW-RHO WHIRLPOOL
INSTALLATION INSTRUCTIONS
SHOWN LESS ALL FITTINGS
THANK YOU...
60
(1524mm)
12
for selecting an American Standard bath. Your new bath is shipped to
WATER
RETENTION
FLANGE
(305mm)
10-1/4
you after careful inspection. the whirlpool version is completely
assembled with pump, motor, and system piping. All you need to finish
the installation are your selected fittings and electrical connections for
a whirlpool. To insure maximum performance and pleasure from this
(260mm)
3/4
(8) JETS
(19mm)
(3 SIDES)
FINISHED
WALL
SEE FITTING
SPECS FOR
DIMENSIONS
16
(406mm)
product, please follow the instructions and cautions.
9
(229 mm)
List of Optional Components (not included):
• Safe-T-Heater 9075.120*
ON/OFF
SWITCH
PUMP
32
(813mm)
CUTOUT IN FLOOR FOR DRAIN
List of Required Components (not included):
ACCESS TO PUMP/MOTOR
THROUGH REMOVABLE
FRONT ACCESS PANEL
C/L OF
SUPPLIES
(2) AIR VALVES
C/L OF
3
• Drain 1583.470*
• Bath Filler*
(76mm)
C/L OF DRAIN
* see your American Standard Dealer
SHOWER ARM
FINISHED
WALL
OPTIONAL TO
FINISHED FLOOR
USUALLY BETWEEN
65 & 78
SAFE-T-HEATER
REMOVABLE
BLANK
1" WATER
RETENTION
FLANGE
C/L OF
VALVES
List of Required Tools and Supplies:
(1651 & 1981mm)
(3 SIDES)
C/L OF
SPOUT
12
(305mm)
C/L OF
OVERFLOW
OPT.
Tools
Supplies
4
TILING
FLANGE
LEVELING STRINGER
NOT FOR SUPPORT
3-1/2
(89mm)
(102 mm)
• Level
• Nails
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard
Woodworking Tools
• Personal Safety
Equipment
• Putty
TOP OF
DECK
UNDERSIDE
OF DECK
21-1/4
21-1/2
(546mm)
• Caulking (waterproof)
• 1 x 3 or 2 x 2
Stringers
(540mm)
REF.
DIM
ROUGH
FLOOR
BATH
SUPPORT
MATERIAL
1-1/2 N.P.T.M.
THREADS
• Drop Cloth
• 15 amp GFI
Outlet
2-3/4
(70mm)
1-1/2 O.D.TAILPIECE
4-5/8
(117mm)
• Cement, Plaster,
Grout
• Caulking Gun
Left-hand version shown
GENERAL SPECIFICATIONS FOR 2425 WHIRLPOOL
General Installation Information
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
60 x 32 x 21-1/2 (1524 x 813 x 546mm)
115 Lbs. (52 Kg.)
Carefully uncrate and inspect your new bath for any shipping damage.
If such damage is found, report it to your vendor immediately. After
inspection and during installation, protect the bath from construction
damage. Before installation, and before enclosing with wallboard,
tile, etc., water test the unit and check for leaks. Do not make
modifications to the whirlpool system or remove pump from factory
mounting. This could adversely affect the safety and performance of
the whirlpool and void the warranty. Do not handle or move the
whirlpool by the pump, motor, or piping system. Fittings (bath filler,
shower arm, etc.) are not provided with the bath and must be ordered
separately. Framing and enclosing materials are provided by others.
574 Lbs. (258 Kg.)
55 Gal. (208 L.)
45 Gal. (171 L.)
16-1/4 x 38-1/4 (413 x 972mm)
26-1/4 x 52-1/2 (667 x 1334mm)
15 (381mm)
43 Lbs./Sq.Ft. (208 Kgs./Sq.m)
(PROJECTED AREA)
PTS.
CUBE (FT3)
20.8
35.3
WHIRLPOOL ELECTRICAL SPECIFICATIONS
PUMP
1.6 HP, 9.7 AMPS,120V.
IMPORTANT: Water test unit before installation and
enclosure!
General Installation Information
Bath may only be installed in a recess type installation.
Locate studs as required. insure rough dimensions are proper, plumb and square. For whirlpools, access to pump/motor may be made
through access opening in apron panel. The following procedure must be used for all installations: leveling support stringer should be as
indicated. this bath is not self-supporting and must be supported along it's entire bottom. Support with mortar or grout. Position
bathtub/whirlpool within the recess, check level, front to back, side to side, and shim as necessary. To secure the tub to wood studs use
drywall screws w/washers or roofing nails immediately above the flange of the tub.To secure the tub to steel studs use 4" drywall screws and
flatwashers.
See page 2 for complete installation information.
Caution: Take extra care when driving nails or screws to avoid damaging the tub. The tile or similar finished floor will be butted against
the bottom of the tub apron, also holding the tub in place.
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.
© American Standard Inc. 2003
All product names listed herein are trademarks
of American Standard Inc. unless otherwise noted.
753456-100 REV. A
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL INSTALLATION INSTRUCTIONS
All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other
applicable codes.
WARNING:
When using electrical products, basic precautions should always be observed, including the following:
1. DANGER: RISK OF ELECTRIC SHOCK
Connect only to a circuit protected by a ground-fault circuit interrupter.
2. Grounding is required. The unit should be installed by a licensed electrician and grounded.
3. Install to permit access for servicing.
4. All building materials and wiring should be routed away from the pump body and heater (if equipped).
The whirlpool should be installed on a 120 vac, 15 amp dedicated circuit. The circuit should be hard-wired from the
electrical power supply panel. The circuit must be a three (3) wire circuit from the electrical supply panel. A grounded
neutral wire and a third wire, earth ground, are essential. Heater equipped models require a separate 15 amp maximum
GFCI circuit. SAFE-T-HEATER EQUIPPED MODELS REQUIRE A SEPARATE 15 AMP MAXIMUM GFCI CIRCUIT.
ELECTRICAL INSTALLATION
SEPARATE
15 GFCI
OUTLET
WHIRLPOOL MOUNTED
120 VAC
AIR SWITCH OR
WALL TIMER
PUMP/MOTOR
GND.
ELECTRICAL DIAGRAM
READ AND FOLLOW ALL INSTRUCTIONS
(3)
753456-100 REV. A
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRE SELECTION GUIDE
Maximum distance from
fusebox to motor
The sizes shown on this
chart are recommendations
for copper conductors
only. Always follow
local and national
Motor
Hi-Performance
Rating
50'
100' 150'
120V Power Line
12 10
200'
1.6
electrical codes
12
8
DRAIN CONNECTION AND SYSTEM TEST
Using recommended drain opening, connect whirlpool drain to waste line. Tighten all drain joints securely. Check the
pump couplings and make sure they are hand-tight. Clean the whirlpool and fill with water to a point 2" above the top of
the highest jet. Recheck the pump couplings and make certain that they are not leaking. (Although the pump couplings
are factory tightened and inspected, some loosening may have occured during transit.) Make sure the whirlpool is
connected to the electrical supply and turn the whirlpool on. Check for leaks around all piping connections while the
whirlpool is running.
POST INSTALLATION CLEAN-UP
Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor.
Do not use wire brushes or any other metal implement on bath surface.
Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or
®
stains may be removed using granular Spic and Span mixed with water.
Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.
HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES.
Abrasive cleaners must not be used since they will scratch and dull the surface. Dulled areas can be restored by rubbing
with a white automotive-type polishing compound and waxing with a liquid wax.
®
753456-100 REV. A
(4)
SPIC AND SPAN IS A REGISTERED TRADEMARK OF PROCTER & GAMBLE
Download from Www.Somanuals.com. All Manuals Search And Download.
|