OneYear LimitedWarranty
Amcor, Inc. (“Amcor”) warrants the original retail purchaser (“Purchaser”) purchasing in the
United States that the Amcor product with which this warranty is enclosed is free from defects
in materials and workmanship.
P O R T A B L E
Air Conditioner
Amcor’s sole obligation under this warranty is to replace, or at Amcor’s discretion, to repair,
free of charge, all defective parts, for a period of one (1) year from date of original purchase.
ANY IMPLIEDWARRANTY OF MERCHANTABILITY IS SIMILARLY LIMITEDTO ONE (1)
YEAR FROM DATE OF ORIGINAL PURCHASE AND NO ACTION BASED UPON ANY
IMPLIEDWARRANTY OF MERCHANTABILITY OR OTHERWISE MAY BE COMMENCED
AFTER EXPIRATION OF ONE (1)YEAR FROM DATE OF ORIGINAL RETAIL PURCHASE.
Some states do not allow limitations on how long an implied warranty lasts,so the above limitation
may not apply to you.
Owner’s Manual
For model CPLMB 14000E
The provisions of this warranty shall not apply to any product which in Amcor’s judgment has
been (1) subject to misuse or neglect. (2) damaged in an accident. (3) used for a purpose for
which it was not designed, or (4) repaired or altered in any way that adversely affected its
performance or reliability.
To obtain warranty service, the defective product or part must be shipped or delivered to:
Amcor’s authorized service center. All postage,insurance and shipping charges are the responsibility
of the Purchaser and are not included in this warranty.
AMCOR NEITHER ASSUMES NOR AUTHORIZES ANY PERSONTO ASSUME FOR IT ANY
OTHER ( LIABILITY IN CONNECTIONWITH ITS PRODUCTS,THEREARE NOWARRANTIES
WHICH EXTEND BEYONDTHE DESCRIPTION ONTHE FACE HEREOF. NO RESPONSIBILITY
ISASSUMED FOR INCIDENTAL OR CONSEQUENTIAL DAMAGESTHAT MAY RESULT FROM
THE USE OFANAMCOR PRODUCT,NOR FORTHE DAMAGES DUETOACCIDENT, ABUSE,
LACK OF RESPONSIBLE CARE,THE AFFIXING OF ANY UNAUTHORIZED ATTACHMENT,
LOSS OF PARTS, OR USE AT AVOLTAGE OTHERTHAN SPECIFIED. Some states do not allow
the exclusion of limitation of incidental or consequential damages, so these limitations may not
apply to you.
Amcor disclaims all liabilities for defects or damages caused by use of replacement parts obtained
from or by service at any service center other than Amcor’s authorized service center.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
It is important
Product: AMCOR Plasma 14000 Portable Air Conditioner Model: CPLMB 14000E
that you read
Date Purchased:_____________________________________
Production Code:________
these instructions
before using your
new purchase and we
strongly recommend
that you keep them
in a safe place for
future reference.
Dear Customer: Please keep this warranty for your record. DO NOT return it.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Thank You!
Always unplug the unit from the wall before performing any maintenance.
• Make sure the unit is drained before moving.
Thank you for purchasing anAMCOR PortableAir Conditioner. AMCOR is a leading
brand in indoor air treatment. We would like you to enjoy the many benefits this
unit offers, so please read this manual carefully and take full advantage of the many
advanced features that your AMCOR Portable Air Conditioner offers you.
Cleaning the Unit:
• Only use a soft damp cloth.
• Never use chemicals, oil-based products, detergents, or other cleaning solutions.
These could damage the cabinet.
AMCOR has specialized in complete indoor environment control, manufacturing
world-class air conditioners,dehumidifiers and air purifiers with innovative technology.
In designing these advanced products, we have listened carefully to our customers
and have passed their views on to our research and development laboratories.
aning the upper Filter:
Cle
lide out the filter holder
• S
We wish you many years of enjoyable use.
from the unit.
After reading this manual, please keep it in a safe place for future reference.
• Separate the filter fixer from
the filter holder (see fig. 1).
Energy SavingTips
• Do not locate the air conditioner where furniture or other objects can obstruct
the airflow.
• Remove the active carbon filter (black) and slide out the 3M Filtrete™ filter (white).
• To clean filters, vacuum with standard vacuum cleaner.
• Keep doors closed so cool air does not escape.
• Keep the filters clean.
• Insert the active carbon filter into the filter holder (see fig. 2).
• Insert the 3M Filtrete™ filter into the filter holder (see fig. 3).
• Fix the filters by reassembling the fixer into the filter holder (see fig. 4).
Set the unit to maximum cooling and high speed fan initially, then adjust the unit
to a comfortable setting.
Cleaning the lower Filter:
• Vaccum with standard vaccum cleaner.
NOTE: Use theTemperature Control (UP/DOWN) to adjust
Air Conditioner cooling to a desired level.
NOTE:
• Before storage be sure filters are clean and dry.
• Should you need to replace filters, contact Amcor for replacement.
• The screen filter must always be used.
• The 3M Filtrete™ Filter should be cleaned periodically. Both filters can be vacuumed.
IMPORTANT: NEVER operate the unit without a filter.
End of Season Storage:
• Unplug the unit.
• Drain the condensed water COMPLETELY.
• Clean the upper and lower filter.
12
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Emptying the Internal Water Container
NOTE: A proper balance between temperature and humidity is critical to maintain a comfortable
living environment. If humidity is high, it will be necessary to empty the Internal water container
frequently, until the ideal humidity is reached.
Model Number
CPLMB 14000E
14,000 BTU/hr
1,100 W / 9.8 A
80 pints / Day
Up to 400 sq. ft.
115V / 60Hz / 1 Phase
Rotary
When the internal water container is full, the back light on the LCD
display flashes. The unit will shut off automatically, beep 15 times and must
be drained before it will restart.
Cooling Capacity
Power Consumption
Humidity Removal Capacity
Recommended room size
Power Supply
To Drain the Unit:
• Switch off the unit and remove the plug from the wall socket.
• DO NOT MOVETHE UNIT. Doing this can result in water
leakage, damaging your floor or carpet.
• Place the drain pan on the floor under the drain cap.
• Remove the drain cap and the rubber stopper from the
drain, and let the water run out. Partially fill the drain pan,
replace the rubber stopper, and empty the drain pan.
This procedure must be repeated until the unit is empty.
Compressor
Refrigerant
R-22
• Replace the rubber stopper and drain cap.
Put plug into the wall socket, and switch the unit on.
The warning signal should be off.
Fan Speed
3 (2 + 1Turbo)
64°F - 90°F
Temperature Set Range
Timer
For Continuous Drainage:
• Switch off the unit and remove the plug from the electrical outlet.
• Remove the Drain Cap and Rubber Stopper. Drain if necessary.
• Connect a DrainTube (not included) (20mm / 3/4" inner dimension) on to the water outlet.
0-24 hours
Weight
75 lbs.
• Place the other end in a drain. Make sure the tube is free from twists and bends.
The tube must decline over its entire length.
Dimensions
20"W x 16"D x 33"H
NOTE: When restarting the unit it may take up to 3 minutes for the compressor to turn on.
REMARKS:
The cooling capacity of the unit may be affected
by the height of the ceiling, quality of insulation,
number of windows, etc.
2
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control
Before Use
Important!
To Operate the Remote Control:
Insert batteries by pulling down on front cover (See fi g. 1).
Be sure the remote is pointed at the unit at all times.
• Leave the unit in an upright position for at least 2 hours before use.
• Always place the unit on an even surface.
1. To Set the Clock:
• Press theTIME button for 3 seconds.
10:09
72
• The power cord has a built-in A.F.C.I. (Arc Fault Circuit Interrupter) circuit breaker
for added safety. If the power supply is interrupted, please press the reset
button to reconnect the unit to the power source. The green light should be on.
F°
• The hour digits will fl ash. Press UP or DOWN to adjust the hour.
ON/OFF
UP
• Press theTIME button.The minute digits will flash.
Press UP or DOWN to adjust the minutes.
• Make sure the unit is connected to a correctly grounded power supply.
• For proper operation, the unit must be vented to the outside.
• Do not cover or obstruct the appliance inlet or outlet grilles.
FAN
DOWN
• Press theTIME button when fi nished.
2. ToTurn Unit ON:
• Press the ON / OFF button
TIME
• To avoid the risk of shock, the product should never be used in bathrooms, shower rooms
or in any other steamy or wet areas.
SLEEP
MODE
3. To AdjustTEMPERATURE:
• Adjust temperature using the UP / DOWN buttons
• Always transport the unit in an upright position.
• Do not sit or stand on the unit.
SWING
4. To Adjust FAN SPEED:
• Press FAN button to select speed.
• Do not place objects on the unit.
5. To Set theTIMER:
A. SET STARTTIME
• Do not touch the unit with wet/damp hands or when standing barefoot.
• Press timer ON button and set the On hour using
• Drainage of the water container is required before moving the unit or
the UP and DOWN buttons.
putting it into storage.
• Press timer ON button and set the minutes using
the UP and DOWN buttons.
• If the electric socket is different from the plug provided, have a professionally qualified
electrician replace the outlet with a suitable one. Avoid the use of adaptor plugs, multiple
sockets and/or extension cords; if their use is necessary, ensure that they conform to the
current safety regulations.
• Press timer ON to finish.
B. SET OFFTIME
Slide
Cover
Down
• Press the timer OFF button and set the Off hour using
the UP and DOWN button.
• Do not pull the power cord or place it near a source of heat; always unroll it completely
to avoid the possibility of dangerous overheating.
• Press the timer OFF button and set the minutes using
the UP and DOWN buttons.
• If the power cord is damaged, it must be replaced by a qualified person.
• Press timer OFF to finish.
6.To Set SLEEP MODE:
THE MANUFACTURER DISCLAIMS ANY RESPONSIBILITY IFTHE ABOVE
INSTRUCTIONS ARE NOT FOLLOWED.
• Make certain unit is operating in Cool Mode.
• Set the desired starting temperature.
• Press SLEEP MODE button.
fig.1
7.To set Auto Grill Mode:
• Press the SWING button for moving louvers
• Press the SWING button again to stop louvers from moving
3
10
Download from Www.Somanuals.com. All Manuals Search And Download.
The CPLMB Unit
Operation
The unit will operate daily according to the timer setting, unless changed.
Air Outlet
After a power failure, or after the unit has been unplugged, you will have to program the
timer settings again.
Control
Panel
Canceling theTimer Setting
Upper air
inlet
In order to cancel the timer programming press theTIME button.
Carrying
Handle
Exhaust Air
outlet
Sleep Mode
The SLEEP MODE gradually adjusts the temperature of the unit 4 degrees upward,
over a 3 hour period, to meet the needs of a body at rest.
Lower air
inlet
Water stopper/
drain cap
Caster
Wheels
To activate the SLEEP MODE:
• Ensure the unit is operating in Cool Mode.
• Set the desired starting temperature.
• Press SLEEP MODE button.
Parts
• In sleep mode fan will operate in low speed.
• To cancel this function press SLEEP MODE button again.
O
N
/O
FF
U
P
FA
N
D
O
W
N
Shutting Off the Blue Light on Control Panel
Normally there is a blue light on the LCD display.
Drain Pan
Exhaust Hose
To shut it off, press the UP and DOWN push buttons at the same time.
The blue backlight will blink twice, and after 3 seconds, will go off.
Remote Control
Insulation Strips
Pressing any of the push buttons will re-light the blue backlight.
Auto Grill Function
1. When unit is being connected (plugged in) to the electricity the louvers open and
close (and stay closed).
Slide Bar
Connector
Adjustable Slide Bar
2. When the ON button is pressed, the louvers open to the maximum and return to an|
angle of 75º above the upper plane of the louvers housing (AUTO GRILL).
Display
3. When the swing push button is pressed, the louvers swing up & down between
30º and 80º above the upper plane of the louvers housing (SWING).
COOLING
4. When the louvers are moving in the swing function, by pressing the swing push button,
the louvers stop moving and remain in the same position (SWING).This enables the
user to direct the airfl ow vertically via the remote control.
FAN
SLEEP
5. When the OFF push button is pressed, the louvers close (AUTO GRILL).
08:15 HOURS: MINUTES
75 ºF TEMPERATURE
4
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Installation of the Window Kit
Timer
In order for this unit to function properly,it must be vented to the outside.
TheTIMER function allows you to program the time the unit turns on and turns off.
Fitting the Exhaust Hose through a window is easy. Please see below.
TO SETTHE TIMER:
• Press theTIME button briefly, the 2 hour digits will flash.
• Press the UP or DOWN button to adjust the hour.
• Press theTIME button again.The 2 minute digits will flash.
• Press the UP or DOWN button briefly to adjust the minutes.
•TheTIME is set. After 10 seconds the time display returns.
Adjustable
Slide Bar
Slide Bar
Programming theTimer for ON:
24:00
Connector
00:00
06:00
• Perform the standard steps as described above.
The circular time scale will be on between the
ON programmed times until 24:00.
18:00
The flashing bar on the time scale indicates the
Exhaust
Hose
real time and moves a segment ahead every
30 minutes until it reaches the ON timer
OFF
ON
time, then the black segments in the circular time
scale will disappear.
Timer Example
Programming theTimer for OFF:
• Perform the standard steps as described above.The circular
time scale will be on between the present time to the OFF
programmed time. The flashing bar on the time scale indicates
the real time and moves a segment ahead every 30 minutes until
it reaches the OFF timer time, then the black segments in the
circular time scale will disappear.
Window Kit Installation:
1. Extend Exhaust Hose at least 6" and insert it into back of the unit, tightening
into place by turning it clockwise.
2. Attach Slide Bar Connector to the other end of the Hose by extending hose at
least 6". Then tighten Hose by turning the Slide Bar Connector clockwise.
3. Place Adjustable Slide Bar in the window and expand so it fits tightly.
4. Mark Slide Bar to record width of the window.
5. Apply Insulation Strips on top and bottom of Slide Bar.
6. Reposition Slide Bar Connector in the window. Expand the Slide Bar to fit tight.
Tighten the screws.
7. Lower the window.
8. Make sure Hose has no kinks.
Slide Bar has 3 sections which allows installation in windows up to 48" in width.
8
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Operation
Test
TEST
IMPORTANT: The air conditioner should be left in
an upright position for at least two hours
Button
Reset
Button
RESET
A.Turning the Unit On:
Green
Light
1. Plug the unit into a working electrical outlet.
2. Make sure the green light on the plug is on.
(If not, press the Reset button.)
3. Press the unit’s ON/OFF Button on the LCD display.
It may take a few minutes before cold air is dispersed.
4. Adjust FAN Speed by pressing the FAN Button
until the preferred fan speed is reached.
5. Press theTIME Button to Set.
B. Setting the Clock:
1. Press theTIME button for 3 seconds to set the clock. The hour digits will flash.
2. Press UP or DOWN to adjust the hour.
3. Press theTIME button, the minute digits will flash.
4. Press UP or DOWN to adjust the minutes.
5. Press theTIME Button to Set.
WARNING!
The length of the exhaust pipe is specially designed according
to the specification of this product.
C. Setting theTemperature:
To change the set temperature press the Up/Down button.
The 2 digit display will indicate the set temperature.
Do not extend it with your own hose, as this
could cause the unit to malfunction.
NOTE: Reaching the set temperature depends on the room and outdoor climatic conditions.
The set temperature range is 64°F to 90°F.
D. Mode Button:
Press the MODE Button repeatedly until the icon representing the desired mode is
displayed (Cool or Fan). On the LCD-display you will see:
Cooling
Fan only
All settings will remain in memory unless power to the unit is shut off.
At re-start, unit will revert back to default temperature setting of 72°F.
E. Fan Speed:
To select the desired fan speed, press the fan button. Options are Slow, Medium, andTurbo.
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
|