Allied Telesis Switch AR44xS User Manual

Software Maintenance Release Note

Version 281-02

for AR750S, AR750S-DP, AR770S, AR415S, AR450S and AR44xS series routers, and AT-8600 series switches

This software maintenance release note lists the issues addressed and enhancements made in Maintenance Version 281-02 for Software Version 2.8.1. Version

details are listed in the following table:

Models

Series

Release File

Date

Size (bytes)

GUI file

AR415S, AR440S, AR441S, AR442S, AR450S

AR400

54281-02.rez

5 September 06

4673896

415s_281-02_en_d.rsc

440s_281-02_en_d.rsc

441s_281-02_en_d.rsc

442s_281-02_en_d.rsc

450s_281-02_en_d.rsc

AR750S, AR750S-DP, AR770S

55281-02.rez

sr281-02.rez

5 September 06

3936164

2251144

750s_281-02_en_d.rsc (AR750S and AR750S-DP)

sr24_281-02_en_d.rsc

AT-8624T/2M, AT-8624PoE, AT-8648T/2SP

AT-8600

Caution: Using a maintenance version on the wrong model may cause unpredictable results, including disruption to the network.

This maintenance release note should be read in conjunction with the following documents:

■

the Release Note for Software Version 2.8.1, available from www.alliedtelesyn.co.nz/documentation/relnotes/relnotes.html

your router or switch’s Document Set for Software Release 2.8.1. This document set is available on the CD-ROM that shipped with your router or switch, or

from www.alliedtelesyn.co.nz/documentation/documentation.html

Caution: Information in this release note is subject to change without notice and does not represent a commitment on the part of Allied Telesis Inc. While every

effort has been made to ensure that the information contained within this document and the features and changes described are accurate, Allied Telesis Inc. can

not accept any type of liability for errors in, or omissions arising from the use of this information.

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-02

Software Maintenance Version 281-02 includes the resolved issues and enhancements in the following tables. In the tables, for each product series:

■

“Y” in a white column indicates that the resolution is available in Version 281-02 for that product series.

“-” in a white column indicates that the issue did not apply to that product series.

a grey-shaded column indicates that Version 281-02 was not released on that product series.

Level 1

Module

PIM 6

Level

Description

For PIM on IPv6, if the interface that was being used as the BSR candidate address

went down, the network occasionally did not re-elect a BSR and the RPs in a

timely manner. This could cause the router or switch to reboot.

CR00006040

This issue has been resolved.

Switch

VLAN

OSPF

If a user created a configuration file that contained port trunk settings before

VLAN port settings, then a loop occurred when the switch rebooted with this

configuration.

CR00007273

CR00013457

CR00013492

This issue has been resolved.

When ports were added to a currently-disabled RSTP domain, the ports could

start to discard packets (because their STP state was set to Discarding).

This issue has been resolved. When ports are added to a disabled RSTP domain,

they remain in a Forwarding state.

When route filters (made with the command add ip route filter) were used to

filter OSPF routes, it was possible for OSPF to constantly remove and re-create an

AS-External LSA. This could prevent OSPF sessions from establishing.

This issue has been resolved.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-02

Module

Core

Level

Description

When a BRI or PRI PIC was installed on the router, an issue with internal memory

handling occasionally caused the router to reboot.

CR00013736

This issue has been resolved.

Switch

If a user created a configuration file that contained LACP settings and VLAN port

settings, then a loop occurred when the switch rebooted with this configuration.

CR00013743

This issue has been resolved.

Level 2

Module

PIM 6

Level

Description

For PIM on IPv6, RPSet information did not expire correctly when all RP

candidates had expired.

CR00010452

This issue has been resolved.

IPv6

The router or switch sometimes forwarded packets to directly connected hosts

whose corresponding IPv6 ND cache entry was still in INCOMPLETE state. This

caused it to send the packets to incorrect MAC addresses and egress ports.

CR00010593

CR00012407

This issue has been resolved.

STAR

When the STAR protocol was used for link-layer encryption, the channel setup

failed continuously on heavy traffic.

This issue has been resolved.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-02

Module

IGMP

Level

Description

If IGMP snooping was enabled but IGMP was not enabled, the snooper behaved

as if IGMP snooping fast leave had been enabled even when it had not been. This

meant that as soon as the snooper received a Leave message, the port left the

group.

CR00012476

This issue has been resolved. Note that fast leave is disabled by default.

STP

When STP was operating with a large number of VLANs in the same STP region,

the switch sometimes rebooted while processing topology change notifications

(TCNs).

CR00012657

This issue has been resolved.

Core, File,

Stack

The command create config=filename set did not copy the configuration file

to all switches in the stack, but only saved the file onto the current switch.

CR00012741

CR00013081

This issue has been resolved.

Switch, STP

When STP was enabled on ports in a trunk group, the non-master ports did not

have the same state as the master port in the switch’s hardware STG table. This

could, on rare occasions, create a broadcast storm.

This issue has been resolved. All ports in a trunk group follow the master port in

the hardware STG table.

ATM

When connected to some types of DSLAMs, the router could reboot due to a

reception error on the SHDSL EOC channel.

CR00013128

This issue has been resolved.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-02

Module

OSPF

Level

Description

It was possible in unusual circumstances for the OSPF link state retransmission list

to grow to a large number. This caused the router or switch to reboot.

CR00013359

This issue has been resolved.

WAN Load

Balancer

It was possible in unusual circumstances for the router to run out of memory after

a WAN load balancer session was added. This could cause the router to reboot

or to stop processing packets.

CR00013390

This issue has been resolved.

Level 3

Module

Core

Level

Description

When a user entered the command show file=switch.ini, the switch previously

CR00003657

could have displayed invalid content or an error message.

This issue has been resolved.

Firewall

When the HTTP proxy URL filter had entries that allowed certain domains and

also had entries that denied certain keywords, the supposedly-allowed domains

were denied if they contained the denied keywords. The proxy allowed the page

/index.html from such domains, but no other pages.

CR00010345

This issue has been resolved. The proxy no longer checks allowed domains

against the keyword list.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-02

Module

Core

Level

Description

When the router or switch sent a RADIUS accounting STOP packet, the packet’s

Acct-Session-Time was always zero, no matter how long the session had been

active for.

CR00011710

This issue has been resolved.

IPv6

Previously, if IPv6 had a dynamic Neighbour Discovery cache entry for a particular

IPv6 address, it prevented users from adding a static entry for the same IPv6

address.

CR00013060

This issue has been resolved. Users can now overwrite dynamic Neighbour

Discovery cache entries with static entries.

IPv6, PIM,

PIMv6

A router or switch running PIM6 occasionally rebooted in certain network

topologies when links were very busy. The circumstances that caused this crash

are very unusual, but the code has been made more robust to cope with them.

CR00013117

CR00013162

ISAKMP

When heartbeats fail for an ISAKMP SA, the router or switch (correctly) removes

the ISAKMP SA and any IPsec SAs that were created by the ISAKMP SA. It then

sends delete messages to notify the peer, so that the peer can also remove the

relevant IPsec SAs.

However, if heartbeats failed just after a re-negotiation, and only failed for the

new ISAKMP SA, then the router or switch did not send delete messages for any

IPsec SAs that were also removed. This could mean that encrypted traffic sent

from the peer was lost.

This issue has been resolved. If heartbeats fail, the router or switch now correctly

sends the peer device a delete message for any removed IPsec SAs.

ISAKMP

Previously, if an ISAKMP policy was configured with set isakmp policy=name

prenegotiate=true and the peer was unresponsive, then at start-up the router

or switch sent fewer ISAKMP message retransmissions than the configured

msgretrylimit value.

CR00013220

This issue has been resolved.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-02

Module

Firewall

Level

Description

When an RTSP media stream, using TCP as the transport protocol, was passing

through the firewall, then the session could stall if some packets were

retransmitted with different sequence numbers to the original transmission.

CR00013415

This issue has been resolved.

DVMRP

Stack

Values for some DVMRP settings (including ttlthreshold and metric) were not

saved in the configuration file or output resulting from the commands create

config and show config dynamic. If the router or switch rebooted, the values

were not applied.

CR00013473

CR00013516

This issue has been resolved.

Different versions of the management stacking feature are not compatible with

each other, which means that AT-9924Ts or x900-24XT series switches can only

be stacked with other AT-9924Ts or x900-24XT switches.

CR00013525

CR00013547

This software version includes checks to prevent incompatible software from

being stacked.

VLAN

When DHCP snooping was enabled on the router or switch, performing a walk

of the MIB variables in that router or switch could result in incorrect termination

of the walk. This was because certain SNMP packets were incorrectly interpreted

as DHCP packets.

This issue has been resolved.

ATM

At low SHDSL bitrates, the EOC channel exhibited many spurious CRC errors.

This issue has been resolved.

CR00013588

CR00013672

An SNMP Walk of the ATM MIB would fail to complete properly, as it would not

advance through the channel list.

This issue has been resolved.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-02

Module

SSH

Level

Description

The router or switch’s SSH server occasionally disconnected an SSH client because

of a checksum error. This occurred because the server did not decrypt the SSH

session key correctly.

CR00013714

This issue has been resolved.

Core

For AR750S-DP routers, the values of the fanAndPsPSUPresent MIB fields

displayed incorrectly. They indicated that a PSU was present when one was not

installed, and that it was not present when it was.

CR00013757

This issue has been resolved.

Level 4

Module

Level

Description

Eth, Bridge,

Switch, LLDP,

IP Gateway

For all Ethernet-like interfaces, the router or switch now uses an ifType value of

ethernetCsmacd, instead of the deprecated value of iso88023Csmacd.

CR00001359

Asyn, Core,

Log, Scripting,

Show

The console port’s autobaud mode was determined incorrectly during start-up.

This caused the router to unnecessarily reconfigure the console port for 9600

8N1 before printing any bootup messages.

CR00013174

This issue has been resolved.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-02

Module

OSPF

Level

Description

After OSPF deleted an AS-External LSA, it sometimes sent an unnecessary LSA

with no changes.

CR00013569

This issue has been resolved.

File

Japanese users can now delete the router or switch’s preferred software release

and the current boot configuration file. For routers or switches that are

manufactured for non-Japanese markets, users must first stop the files from

being preferred, by setting new preferred files or by using the commands delete

install=pref or set config=none.

CR00013683

CR00013767

Core

In Japan, AT-8624PoE switches are named 8624PS. Previously, 8624PS switches

displayed AT-8624PoE as their board name in the output of the command show

system.

This issue has been resolved. For Japanese switches only, the board name is now

8624PS.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-02

Enhancements

Module

Level

Description

ATM

Previously, it was not possible to set the MTU for an ATM interface.

CR00013126

This enhancement makes it possible to now do so. The MTU can be set to values

between 256 bytes and 1600 bytes, inclusive.

NAT-T, IPsec

This software version supports more versions of IPsec NAT-T. As well as the

existing support for versions 2 and 8 of the NAT-T draft, the router now:

CR00013130

■ supports NAT-T draft version 3, as defined by draft-ietf-ipsec-nat-t-ike-03.txt.

This version has also been implemented by SonicWALL in its EnhancedOS.

■ supports RFC 3947. This RFC has also been implemented in Linux’s Openswan,

for example (www.openswan.org).

■ accepts and sends the IPsec draft version 2 Vendor ID string when the hash

does not include a carrage return. Therefore it accepts and sends a hash of

“draft-ietf-ipsec-nat-t-ike-02” as well as a hash of “draft-ietf-ipsec-nat-t-

ike-02\n”

■ displays some other Vendor IDs in debugging information even though the

router does not support these versions. Such Vendor IDs are followed by the

phrase “info only”.

IP Gateway

RIPv2 can now use authentication passwords that contain almost any printable

character, including characters such as $, % and &. The ? character is interpreted

as asking for parameter help, so this is not usable anywhere inside a password.

Also, a password cannot contain double quotes (") as the first character of the

string.

CR00013444

The RIP password length is now strictly enforced at 16 characters. The command

handler no longer accepts a password with more characters than this.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-02

Module

SHDSL

Level

Description

The 4-wire support of SHDSL interfaces has been enhanced to provide support

for a standards-based train-up mode as well as the existing enhanced train-up

mode.

CR00013447

This issue has been resolved.

File

PoE

Previously, a user could rename the current boot configuration file (by using the

command rename). This stopped the router or switch from running that

configuration on boot-up, so if the router or switch restarted after the user had

renamed the current boot configuration file, it started up with no configuration.

CR00013535

CR00013677

This issue has been resolved. Users can no longer rename the current boot

configuration file.

This enhancement added support for the latest version of the PoE firmware

(version 5.0.1), so that AT-8624PoE switches can be shipped from the factory

with this firmware version.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-01

Software Maintenance Version 281-01 includes the resolved issues and enhancements in the following tables. In the tables, for each product series:

■

“Y” indicates that the resolution is available in Version 281-01 for that product series.

“-” indicates that the issue did not apply to that product series.

Level 1

Module

Switch

Level

Description

If an AT-9924SP had a large number of SFPs installed and had a very high level of

traffic passing through the network, sometimes newly inserted SFPs were not

detected.

CR00012654

This issue has been resolved.

DHCP

In some configurations in which the DHCP server was enabled, the router or

switch compacted its flash memory frequently. This occurred because the DHCP

server unnecessarily updated record files in flash memory even if the record had

not changed.

CR00012715

CR00012760

This issue has been resolved, so that DHCP records are only updated when

necessary. Note that if the router or switch has NVS memory, it stores DHCP

records in NVS by preference, instead of in flash memory.

Log

Entering the command show debug caused the router or switch to reboot if one

or more long messages existed in the log.

This issue has been resolved.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-01

Module

Switch

Level

Description

When STP is enabled on the switch but is disabled for a trunk (by using the

command disable stp port), the trunk should pass traffic. Previously, some trunk

members sometimes stayed in the “discarding” state instead.

CR00012933

This issue has been resolved.

DVMRP

Receiving a DVMRP Graft or Prune message occasionally caused the router or

switch to reboot.

CR00013025

CR00013413

This issue has been resolved.

IP Gateway,

Load Balancer

If the router or switch was configured with a local interface IP address and the

interface to which this address belonged did not have a logical interface with

index 0, a number of connectivity issues from this router or switch occurred, in

which the router or switch was not able to communicate with UDP, TCP or PING.

This issue has been resolved.

SSL

When the router or switch used SSL to process HTTPS traffic, it rebooted.

CR00013666

This issue occurred, for example, when browsing securely to the GUI, or when

the load balancer was configured to support HTTPS traffic.

This issue has been resolved.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-01

Level 2

Module

Bridge

Level

Description

The Bridge cannot be configured to bridge PPPoE packets from an Ethernet

interface that has also been configured as a PPPoE interface. Previously, such a

Bridge configuration would appear to succeed. However the Bridge would not

bridge PPPoE packets and the router would restart when the command reset

bridge was entered.

CR00009212

This issue has been resolved. Note: if you want to bridge PPPoE packets, do not

also configure the router as a PPPoE endpoint (by using the command create

ppp=number over=ethx-any).

MSTP

Because of an MSTP issue, the switch did not always send a BPDU with an

agreement flag to its designated bridge, even if the switch was synchronised with

the latest spanning tree information from the designated bridge. This prevented

the designated port on the designated bridge from making a fast transition to

the forwarding state. The result was that the network could take up to two times

the “forward delay” time to fully converge.

CR00009213

CR00009826

CR00010513

This issue has been resolved.

IP Gateway

When a static ARP is deleted, the router or switch sends out an ARP request to

attempt to create a dynamic ARP for that IP address. Previously, the router or

switch did not process the ARP response correctly and therefore did not add the

ARP to its ARP table.

This issue has been resolved. When a static ARP is deleted, the router or switch

attempts to create a dynamic ARP for that IP address, and will successfully add it

to the ARP table if a device responds.

BGP,

BGP did not update its route table when a blackhole route changed in IP.

This issue has been resolved.

IP Gateway

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-01

Module

File

Level

Description

The router or switch sometimes rebooted when copying a very large file (several

Mbytes). This issue has been resolved by improving the copy process so that it

uses fewer memory buffers.

CR00011434

Switch

IPv6

On x900-48 Series switches, when the switch used a DSCP map to remark

packets, it did not mark the packets correctly.

CR00011670

CR00012364

This issue has been resolved.

For IPv6, if there were multiple equal cost multipath (ECMP) static routes to a

destination, and one or more links for the routes became inactive, the inactive

route was sometimes still chosen for forwarding. This caused brief data delivery

failure to the destination.

This issue has been resolved.

IP Gateway

If the router or switch received an IP packet that had been sent as an Ethernet

broadcast, the router or switch responded as if the packet had been sent to its IP

address, even when the packet was destined for a different IP address. In

particular, the router or switch processed and responded to ICMP and TCP

packets that were sent as Ethernet broadcasts to different IP addresses. These

caused the router or switch to send ICMP echo responses or TCP reset packets.

CR00012534

This issue has been resolved. Such Ethernet broadcast packets are generally not

valid packets, so the router or switch now discards them.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-01

Module

Firewall

Level

Description

When the WAN load balancer was used with IP NAT (instead of firewall NAT), and

an FTP session was established to a server on the public network, the router did

not correctly establish a return session. This meant data was unable to flow

correctly back from the server, and the router rebooted.

CR00012613

This issue has been resolved.

Note that the WAN load balancer is not designed for use with IP NAT, because IP

NATs are not associated with interfaces. Configurations that use an IP NAT cannot

vary the global IP address (the gblip parameter) based on the outgoing interface,

so the WAN load balancer sends all traffic out with the same source address.

Therefore, the return traffic probably comes back via the WAN load balancer

resource that is associated with the global IP. The impact is that the WAN load

balancer balances the outgoing traffic but not the return traffic.

We recommend using firewall NAT instead of IP NAT with the WAN load balancer.

VRRP,

IP Gateway

Under certain network conditions in which VRRP entities become temporarily

unsynchronised, the router or switch could receive a gratuitous ARP from a self-

elected VRRP master when the router or switch was still the master. This caused

the existing master to create an ARP entry that incorrectly redirected packets

towards the other VRRP entity even after the other entity had become a slave

again.

CR00012624

This issue has been resolved. The router or switch no longer accepts gratuitous

ARPs from other VRRP entities while it is still the Master.

Switch

After the AR770S rebooted, the Port Link/Activity and Duplex/Collision LEDs

sometimes did not blink in response to activity and collisions, respectively.

CR00012683

This issue has been resolved. The router detects the problem and recovers from

it, if possible. If it cannot recover from the problem, it generates a log message

of severity 6, module SWK, type REST, and subtype FAIL. The log message says

“An LED error has been detected, please power-cycle the device. If this message

appears again, contact your technical support representative for help.”

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-01

Module

Level

Description

IPsec, ENCO

Decrypting a large IPsec ESP packet sometimes caused the router or switch to

reboot.

CR00012697

This issue has been resolved.

Core

Soft errors can generate exceptions that would cause the router or switch to

reboot. Soft errors are spontaneous changes in the information stored in a digital

circuit, caused by physical effects. The router or switch’s handling of such errors

has been improved, so that it recovers without rebooting when possible.

CR00012710

Core, File,

Stack

The command create config=filename set did not copy the configuration file

to all switches in the stack, but only saved the file onto the current switch.

CR00012741

CR00012757

This issue has been resolved.

OSPF

The router or switch correctly accepted the command add ospf redistribution

protocol=static followed by the command set ospf asexternal=on or nssa.

However, the command create config did not create a valid configuration file

from these commands. If the router or switch used that configuration after a

reboot, it gave the error “Redistribution for specified routing protocol - already

exists” and did not use the user-defined redistribution definition.

This issue has been resolved. The router or switch now correctly saves and uses

the user-defined redistribution definition.

DHCP

Snooping,

When the switch had two DHCP snooping classifiers applied across all 48 ports,

and maxleases was set to 10 or more on each port, the switch rebooted.

CR00012820

CR00012821

Switch

This issue has been resolved.

IP Gateway

When adding, deleting or updating subnet routes of a more general route, the

software and hardware IP route tables sometimes became unsynchronised. The

same issue sometimes also occurred when updating ECMP routes. This could

cause the router or switch to forward packets to unexpected next hops.

This issue has been resolved.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-01

Module

Level

Description

ASYN, Log

The following issues occurred with sending log messages to an asynchronous

port:

CR00012846

■ The log messages output on an asynchronous port were corrupt.

■ When log messages were output to an asynchronous port, that port was

(correctly) locked. However, the port remained locked after the asynchronous

log output definition was destroyed, and after the log output's destination

was changed from asynchronous to something else.

■ It was possible for a user to change the log output destination to an

asynchronous port while the user was logged into the asynchronous port. This

resulted in the user losing access to the command line interface.

■ It was possible to create a log output definition with an asynchronous port as

the destination even when another user was logged into that asynchronous

port. This resulted in the other user losing access to the command line

interface.

■ If a user changed the log output destination to an asynchronous port and

specified invalid parameters in the command, an error message was displayed

but the new output destination was saved anyway.

■ The set command allowed a user to specify an asynchronous port as the

destination without specifying the asynchronous port number. The number

defaulted to asyn0, which may not have been the desired port.

These issues have been resolved.

Core

If the switch was rebooted at a time when there was a high level of packet traffic

between the switch ports and the switch CPU, then during the reboot process it

was possible for RAM test errors to occur.

CR00012855

This issue has been resolved.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-01

Module

ENCO

Level

Description

Entering the command create enco key=number ip=? caused the router or

CR00012868

switch to reboot.

This issue has been resolved.

IPv6, Switch

When an IPv6 accelerator card was installed, IPv6 multicast traffic was flooded to

all ports in a downstream VLAN, whether or not they had joined the multicast

group.

CR00012900

This issue has been resolved.

Switch, VLAN,

User

Under very rare circumstances, memory corruption could occur when packets

were transmitted by the CPU out a switch port.

CR00012911

CR00012951

This issue has been resolved.

IPv6

RIPng (for IPv6) sometimes sent sub-optimal routes to its neighbours. When

RIPng was configured in a network with loop topology, this could cause unstable

routing table entries on the neighbours (the metric kept being updated, as a

result of updates from neighbours).

This issue has been resolved. RIPng no longer sends sub-optimal routes.

Bridge

ATM

If a tagged packet was bridged out of a VLAN interface, the interface always

added a VLAN tag into the packet, even though the packet was already tagged.

CR00012952

CR00012991

This issue has been resolved.

The maximum allowed value of the vpi parameter in the commands add and set

atm channel has been increased from 8 to 15.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-01

Module

Level

Description

EPSR, Switch

When EPSR is enabled, it creates a classifier so it can send EPSR packets to the

CPU for processing. Previously, if too many classifiers existed and therefore EPSR

could not create the classifier, EPSR was enabled anyway. However, it did not

work correctly.

CR00013003

This issue has been resolved. Now, if EPSR cannot create the classifier, an error

message displays and EPSR is not enabled.

IPv6

When an IPv6 address was deleted on the router or switch, and that IPv6 address

had previously been learnt by a remote IPv6 node, then the router or switch

would reboot if it received an ICMPv6 Neighbour Solicitation message from the

remote node. This meant, for example, that if you successfully pinged an address

on the router or switch, then deleted that address, then attempted to ping the

old address again, the router or switch would reboot.

CR00013077

This issue has been resolved.

IP Gateway

UPnP

If the router or switch attempted to email log output, and used a domain name

server that gave a non-standard response to the DNS query, the router or switch

sometimes rebooted.

CR00013234

CR00013276

CR00013309

This issue has been resolved.

In UPnP, Msearch requests were stored indefinitely, which eventually exhausted

the router’s memory and caused it to reboot.

This issue has been resolved. Msearch requests are now deleted once the router

has finished with them.

L2TP

When an L2TP LAC Client (for example, a Microsoft Windows XP VPN Client)

activated an L2TP tunnel to a router or switch that was operating as an LNS, the

dynamic PPP interface on the LNS left out the PPP authentication phase.

This also prevented the interface from obtaining an IP address by remote IP

assignment from a User Database entry.

This issue has been resolved.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-01

Module

EPSR

Level

Description

The switch correctly accepted a changed ring flap time (the commands create or

set epsr ringflaptime). However, if the command create config was used to

save the configuration and the switch used that configuration after a reboot,

EPSR failed.

CR00013407

This issue has been resolved.

PIMv6

When the router or switch used PIM for multicast routing, and an IPv6 multicast

client joined a group, then left it, then attempted to rejoin it, sometimes the

attempt to rejoin was not successful.

CR00013529

This issue has been resolved.

Level 3

Module

TTY

Level

Description

Editing a text file that consisted of a very large number of lines (approaching or

exceeding 30,000 lines) caused the router or switch to reboot.

CR00008766

This issue has been resolved.

Asyn

If information was sent to a console (asyn) port that had no cable plugged into

it, excessive CPU usage occurred.

CR00011444

This issue has been resolved.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-01

Module

Level

Description

WAN load

balancer

WAN load balancer performance has been improved, especially through

improvements to the session hashing mechanism.

CR00012309

OSPF

An OSPF router or switch could show large numbers of entries in its

retransmission lists to certain neighbours under certain conditions (for example,

in a congested Frame Relay network). In some cases, the number of items in the

list was larger than the number of LSAs in the database.

CR00012468

This issue has been resolved.

Also, a new NRL debugging option has been added to OSPF, to show additions

to and deletions from the neighbour retransmission list. To enable NRL

debugging, use the command:

enable ospf debug=nrl

Note that this option may generate large amounts of debugging output on a

large OSPF network. Use it with care.

To disable NRL debugging, use the command:

disable ospf debug=nrl

OSPF

In an OSPF NSSA, changing the router ID of the OSPF NSSA ASBR sometimes

caused the area border router to behave incorrectly.

CR00012598

CR00012607

This issue has been resolved.

Switch

IPv6 multicast routing using the IPv6 accelerator card on an AT-9924T or AT-8948

switch sometimes caused very high CPU utilisation, even though multicast data

is switched at wirespeed by the accelerator card.

This issue has been resolved.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-01

Module

many

Level

Description

The command show debug active displays information about currently-active

debugging for many modules at once. Similarly, the command disable debug

active disables debugging for many modules in a single step.

CR00012708

This Software Version extends the list of modules that these commands act on.

They now apply to all modules with debug support, except for DS3, ACC, Q931,

SA, SYN, TPAD, and X25C.

IP Gateway

When a link that had RIP configured on it went down, so that the router or switch

used an alternative route, output from the command show ip route sometimes

displayed incorrect information when the link came back up. When the link first

comes back up, the route's RIP metric is still 16, so the alternative route is still the

“best” route to the target. However, show ip route sometimes displayed a

disabled route over the original link, with a RIP metric of 16, as the best route,

even though the router or switch correctly used the alternative route.

CR00012786

This issue has been resolved.

IP Gateway

Previously, the router accepted ARP entries with multicast IP and MAC addresses

when the MAC disparity feature was disabled. The MAC disparity feature is

disabled by default.

CR00012895

The issue has been resolved. The router now discards such ARP entries unless the

MAC disparity feature has been enabled by using the command enable ip

macdisparity.

Log

When a user entered the command show log receive=ipadd mask=mask, the

router or switch displayed an error message that said mask was not a valid

parameter.

CR00012947

CR00013007

This issue has been resolved. The mask parameter is now valid for this command.

IPsec

With tunnel-mode IPsec, the router or switch decremented the time to live (TTL)

of IP packets twice when it forwarded the packets through the tunnel.

This issue has been resolved.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-01

Module

Firewall

Level

Description

When IP NAT or firewall NAT was used, the router or switch sometimes generated

ICMP messages that specified the wrong source IP address. This meant that the

response to traceroute could be incorrect.

CR00013048

This issue has been resolved.

IPv6

The router or switch sometimes rebooted when it processed a large number of

multicast routes that were created as the result of receiving a large amount of

data from more than 500 multicast groups.

CR00013049

CR00013085

This issue has been resolved.

OSPF

A user can configure a range on an OSPF ABR, so that the ABR aggregates the

network advertisements from one area into another area in the form of summary

LSAs. However, networks advertised into a transit area should not be aggregated

into summary LSAs. Previously, the router or switch advertised aggregated

summary LSAs into transit areas when a range had been configured.

This issue has been resolved. When the router or switch is advertising into a

transit area, it ignores any configured range.

Switch

Core

When traffic on a port was mirrored and that port had a learn limit set, packets

from the CPU (such as ARP replies and ICMP replies) were not always mirrored.

CR00013093

CR00013190

This issue has been resolved.

If a AT-8624PoE switch had a sticky fan, the fan constantly toggled between

running at full speed and slowing down. This meant that the fan continuously

generated alarms.

This issue has been resolved. If the fan reports an error more than 3 times in an

hour, it now remains at its maximum speed setting.

Core

On the AT-8624PoE switch, a fan fault alarm was not generated when the fan

speed dropped to 70% of the expected speed.

CR00013202

This issue has been resolved. When the speed drops to 70% or less, a alarm is

now generated.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-01

Module

Core

Level

Description

The system LED did not indicate when an internal power supply fault occurred.

CR00013243

This issue has been resolved. The system LED now flashes 3 times to indicate a

fault. Also, output of the show system command now reports voltages more

accurately.

OSPF

When a user changed the OSPF priority of an interface, the router or switch did

not immediately perform the process to elect a Designated Router and Backup

Designated Router (BDR).

CR00013279

CR00013353

This issue has been resolved.

Switch

Certain BIST and AUTOBURNIN tests reported errors, especially if an IPv6

accelerator was installed. Also, if a user entered the commands disable or

enable switch learning and an IPv6 accelerator was installed, the switch

displayed an error message that said:

“SWI ERROR: (1) swmxMacLearningSet [1] - Unable to set learning”

These issues have been resolved.

BGP

When a user created a BGP module trigger for the peerstate event, the router

or switch did not allow specification of the script or state parameters.

CR00013421

CR00013538

This issue has been resolved. All such generic parameters are now available with

module-specific triggers.

IP Gateway

Software Version 2.8.1 introduced a new msgtype parameter for the command

add igmp filter, which enables users to filter on IGMP query, report or leave

messages. This parameter was mistakenly made compulsory. Therefore, if an

existing configuration script contained IGMP filters, and the router or switch

restarted with that configuration, the filters did not work.

This issue has been resolved. The msgtype parameter is now optional, with a

default of report.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-01

Level 4

Module

GUI

Level

Description

When the web-based GUI is used to add or remove ports from a port-based

VLAN association on an AT-9812T switch, the icons representing alternate ports

faced opposite directions.

CR00010159

This issue has been resolved. The port icons now all have the same orientation.

IPsec

In output of the commands show ipsec policy and show ipsec policy

sabundle, the value for the number of bytes currently used by each SA bundle

was sometimes truncated.

CR00011311

This issue has been resolved, and both commands now display the correct

number. As part of this, output of the command show ipsec policy has been

modified so that the expiry limits in bytes and in seconds display on separate

lines.

Also, if the expirykbytes parameter of the command create or set ipsec

bundlespecification was given a value higher than 4193280, the router or

switch instead used a lower value.

This issue has been resolved. If you specify a value above 4193280, the router or

switch now displays a warning message and sets the expiry limit to 4193280

kbytes.

IP Gateway

Previously the switch allowed users to specify the tag parameter when creating

or modifying a blackhole route with the commands add or set ip route.

However, blackhole routes cannot be tagged, so the switch did not apply the tag

setting in its saved configuration.

CR00011788

This issue has been resolved. If a command contains both the blackhole and tag

parameters, the switch now returns an error message.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-01

Module

Level

Description

Remote Telnet

The “?” help description for the enable command stated that the parameter

rtelnet would “Disable the use of remote telnet to control an asyn port”.

CR00012270

This issue has been resolved. The query now states that the command enable

rtelnet enables remote telnet.

PPP

GUI

Output of the command show ppp idletimer did not display the PPP interface

name.

CR00012581

CR00012655

This issue has been resolved.

The web-based Graphical User Interface (GUI) did not display software QoS

counters.

This issue has been resolved. The counters now display correctly. To access them,

select Diagnostics in the left-hand menu.

Install,

Stacking

If the local command show config dynamic was entered as a host-directed

command, the switch gave an incorrect error message.

CR00012755

CR00012774

CR00012824

This issue has been resolved. If you attempt to direct show config dynamic to

a host, the switch now responds with the message “Command is local, do not

use host direction”.

IP Gateway,

TCP

In an unusual network configuration where the IP subnet on one interface was a

subset of that on another interface, it was possible for the results of a trace route

to show erroneous information.

This issue has been resolved. A search for an interface using an address within

the interface's subnet now finds the most specific match for the address.

GUI

Internet Explorer did not display the switch trunking summary page correctly. If

the user selected a trunk group, the radio button displayed a grey image, instead

of displaying a black dot inside a circle. This was only a display issue—the GUI

acted on the selected trunk group correctly.

This issue has been resolved.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-01

Module

L2TP

Level

Description

When the router or switch was configured as an LNS and received an incoming

L2TP call that was associated with a disabled PPP interface, it produced an

incorrect log message.

CR00012916

This issue has been resolved.

Log

IPv6

When a user entered the command show log receive=ipadd, information

about all IP addresses was displayed unless the user also entered the mask

parameter.

CR00012946

CR00013086

CR00013115

This issue has been resolved. Specifying an IP address without a mask now limits

the display to information about that IP address.

When the router or switch was running MLD and sent an MLD query packet, it

incremented the OutEchos counter instead of the OutGroupMembQueries

counter.

This issue has been resolved. To see the OutGroupMembQueries counter, enter

the command show ipv6 counter.

IP Gateway

The “?” help description for the fragment parameter of the add ip interface

command was unclear.

This issue has been resolved. The query now states that the parameter “Decides

if Do Not Fragment is obeyed for IP packet larger than MTU”.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-01

Enhancements

Module

Bridge

Level

Description

By default, when the router receives a tagged packet on an Eth or VLAN interface

and bridges it, the bridge strips out the packet’s VLAN tag. This enhancement

enables you to set the bridge to instead retain the tag, by using off, no or false

in the new command:

CR00012620

set bridge stripvlantag={on|off|yes|no|true|false}

The default is on. To see whether stripping is turned on or off, use the command:

show bridge

and check the new StripVlantag entry.

L2TP

The connection between the router or switch, acting as an LNS, and a third party

peer, acting as an LAC, can sometimes fail during PPP link negotiation. Frequent

negotiation failures can indicate a compatibility problem between the third party

peer and Proxy Authentication responses from the router or switch. With this

enhancement, you can now disable Proxy Authentication on the router or switch

for situations where the third party equipment is not compatible. Use

proxyauth=off in the command:

CR00012692

add l2tp ip=ipadd[-ipadd] ppptemplate=0..31

[number={off|on|startup}] [pre13={off|on}]

[proxyauth={off|on}]

[tosreflect={off|on|false|true|no|yes}]

The default for proxyauth is on. Proxy Authentication should not be disabled

unless necessary.

To see whether Proxy Authentication is turned on or off, use the command:

show l2tp ip

and check the new Proxy Authentication entry.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Features in 281-01

Module

File

Level

Description

Previously, a user could delete the preferred software release and the current

boot configuration file (by using the command delete file), without first setting

a new preferred release or boot configuration file. Therefore, it was possible to

accidentally delete these files, which caused network disruptions if the router or

switch restarted. If the router or switch restarted after the user had deleted the

preferred release, it booted from the fallback software. Similarly, if the router or

switch restarted after the user had deleted the current boot configuration file, it

started up with no configuration.

CR00012850

CR00013109

This enhancement ensures that users can no longer delete the preferred software

release or the current boot configuration file. If you want to delete the files

without specifying new preferred files, first use the commands delete

install=pref or set config=none to stop the files from being preferred.

Core, SNMP,

Stack

Stacked devices are now SNMP accessible through a single IP address. The MIB

Object stackSnmpHost (at-stack.mib) is used to determine which stacked device

is currently responding to SNMP Requests. By setting the value of

CR00012857

CR00011277

stackSnmpHost, an SNMP manager can chose any one of the stacked switches

to poll. After a new value is set successfully, a new SNMP agent is chosen. On

SNMP V1 and V2c operations, the new agent is immediately ready to talk to the

manager. On SNMP v3 operations, the manager needs to re-run engine discovery

to re-synchronize the agent and manager.

Traps and notifications from stacked devices now include an extra object called

hostID, which gives the value of the switch’s host ID. This identifies which stacked

switch produced the trap or notification.

Switch

Core

New AT-8600 Series switches are now ROHS compliant (lead free). This

enhancement ensured that the new ROHS compliant 1 gigabit uplink ports are

fully supported on AT-8648T/2SP switches.

CR00013394

CR00013584

On AT-8624PoE switches, a new 7000 rpm fan is now supported.

Version 281-02

C613-10482-00 REV B

Download from Www.Somanuals.com. All Manuals Search And Download.

Acnodes Personal Computer RMC 7132 User Manual
Addonics Technologies Model Vehicle CCM35MK1 E User Manual
AG Neovo Computer Monitor SX 19 User Manual
Aiphone Intercom System AN 8540DS User Manual
Akai Musical Instrument EWI5000 User Manual
Alvin High Chair DC999 User Manual
American Standard Hot Tub 2422L002 User Manual
Avital Automobile Alarm AviStart 6001 User Manual
Behringer Recording Equipment C 1 User Manual
Beko Refrigerator BK 7681 User Manual