Washer-Extractors
Cabinet Freestanding
WE-8 Computer
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. 9001889R7
July 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property
damage.
W030
NOTE: The WARNING and IMPORTANT instructions appearing in this manual are not meant to cover all
possible conditions and situations that may occur. It must be understood that common sense, caution, and
carefulness are factors which cannot be built into these washers. These factors MUST BE supplied by the
person(s) installing, maintaining, or operating the washer.
Always contact the distributor, service agent, or the manufacturer about any problems or conditions you do not
understand.
9001889
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction.........................................................................................
3
Table of
Contents
Programming ......................................................................................
Setup of the Chemical Hold Feature
4
(Version 1.11 and later ONLY)......................................................
7
Edit a Cycle........................................................................................... 18
Delete a Step .................................................................................... 22
Insert a Step...................................................................................... 23
Delete a Cycle....................................................................................... 25
Cycle Count .......................................................................................... 27
Speed Calibration.................................................................................. 29
Pre-Programmed Cycles .................................................................... 30
© Copyright 2011, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Model Identification
Information in this manual is applicable to these
models:
HX018PVQM7 HX18PVXU6
SX18PVQU6
UX018PVQM7 UX18PVPA7
UX018PVXA7 UX18PVPU6
UX018PVXM7 UX18PVQA6
UX18PVXA6
UX18PVXA7
UX18PVXM6
UX18PVXM7
HX018PVXM7 SX018PVPA7 SX18PVXM6
HX18PVQM6 SX018PVQM7 SX18PVXM7
HX18PVQM7 SX018PVXM7 SX18PVXU6
UX18PVNA6
UX18PVQA7
18
HX18PVQU6
HX18PVXM6 SX18PVQM6
HX18PVXM7 SX18PVQM7
SX18PVPA7
UX018PVNA7 UX18PVNA7
UX018PVPA7 UX18PVNU6
UX018PVQA7 UX18PVPA6
UX18PVQM6 UX18PVXU6
UX18PVQM7
UX18PVQU6
HX025PVQM7 HX25PVXU6
HX025PVXM7 SX025PVQM7 SX25PVXU6
SX25PVXM7
UX025PVXM7 UX25PVQA6
UX25PVNA6 UX25PVQA7
HX25PVQM6 SX025PVXM7 UX025PVNA7 UX25PVNA7
UX25PVXM6
UX25PVXM7
UX25PVQM6 UX25PVXU6
UX25PVQM7
HX25PVQM7 SX25PVQM6
HX25PVQU6 SX25PVQM7
HX25PVXM6 SX25PVQU6
HX25PVXM7 SX25PVXM6
UX025PVPA7 UX25PVNU6
UX025PVQA7 UX25PVPA6
UX025PVQM7 UX25PVPA7
UX025PVXA7 UX25PVPU6
25
33
35
UX25PVQU6
UX25PVXA6
UX25PVXA7
UX33PVNA7
UX33PVPA7
UX33PVQA7
UX33PVQM7 UX33PVXA7
UX035PVQM7 UX35PVPA7
UX035PVXA7 UX35PVPU6
UX035PVXM7 UX35PVQA6
UX33PVXM7
HX035PVQM7 HX35PVXU6
SX35PVQU6
UX35PVXA6
UX35PVXA7
UX35PVXM6
UX35PVXM7
HX035PVXM7 SX035PVNM7 SX35PVXM6
HX35PVQM6 SX035PVQM7 SX35PVXM7
HX35PVQM7 SX035PVXM7 SX35PVXU6
HX35PVQU6
HX35PVXM6 SX35PVQM6
HX35PVXM7 SX35PVQM7
UX35PVNA6
UX35PVQA7
SX35PVNM7
UX035PVNA7 UX35PVNA7
UX035PVPA7 UX35PVNU6
UX035PVQA7 UX35PVPA6
UX35PVQM6 UX35PVXU6
UX35PVQM7
UX35PVQU6
UX40PVNA7
UX40PVPA7
UX40PVQA7
UX40PVQM7 UX40PVXA7
UX40PVXM7
40
55
HX055PVNU7 HX55PVQU7
HX055PVQU7 HX55PVXU6
HX055PVXU7 HX55PVXU7
HX55PVNU6
HX55PVNU7
HX55PVQU6
SX055PVXU7 SX55PVQU7
SX55PVNU6
SX55PVNU7
UX055PVXU7 UX55PVQU7
SX55PVXU6
SX55PVXU7
UX55PVNU6
UX55PVNU7
UX55PVXU6
UX55PVXU7
SX055PVNU7 SX55PVPU6
SX055PVPU7 SX55PVPU7
SX055PVQU7 SX55PVQU6
UX055PVNU7 UX55PVPU6
UX055PVPU7 UX55PVPU7
UX055PVQU7 UX55PVQU6
HX075PVNU7 HX75PVPU7
HX075PVPU7 HX75PVQU6
HX075PVQU7 HX75PVQU7
SX075PVQU7 SX75PVQU7
SX75PVNU6
SX75PVNU7
UX75PVNU7
UX075PVNU7 UX75PVPU6
UX075PVPUU UX75PVPU7
75
HX75PVNU6
HX75PVNU7
SX075PVNU7 SX75PVPU7
SX075PVPU7 SX75PVQU6
X075PVQU7
UX75PVNU6
UX75PVQU6
UX75PVQU7
HX100PVNU6 HX100PVQU6 SX100PVNU7 SX100PVQU7 UX100PVPU6 UX100PVQU7
HX100PVNU7 HX100PVQU7 SX100PVPU7 UX100PVNU6 UX100PVPU7
HX100PVPU7 SX100PVNU6 SX100PVQU6 UX100PVNU7 UX100PVQU6
100
135
HX135PVNU6 HX135PVQU6 SX135PVNU7 SX135PVQU7 UX135PVPU6 UX135PVQU7
HX135PVNU7 HX135PVQU7 SX135PVPU7 UX135PVNU6 UX135PVPU7
HX135PVPU7 SX135PVNU6 SX135PVQU6 UX135PVNU7 UX135PVQU6
HX165PVNU6 HX165PVQU6 SX165PVNU7 SX165PVQU7 UX165PVPU6 UX165PVQU7
HX165PVNU7 HX165PVQU7 SX165PVPU7 UX165PVNU6 UX165PVPU7
HX165PVPU7 SX165PVNU6 SX165PVQU6 UX165PVNU7 UX165PVQU6
165
200
HX200PVNU7 HX200PVQU7 SX200PVPU7 UX200PVNU7 UX200PVQU7
HX200PVPU7 SX200PVNU7 SX200PVQU7 UX200PVPU7
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
Setup of the Machine
Turn key from Run to Program
RUN
PROGRAM
To go to the main setup of the machine, press
“Auxiliary”, “2”, “9”.
Program Cycle 00
System Program
_X18PV
To change the machine type, press the “Advance”
button.
The following types are possible:
System Program
_X25PV
_X18PV
_X25PV
_X33PV
_X40PV
_X55PV
_X75PV
_X135PV
_X165PV
_X200PV
Press the “Advance” button until the right type of
machine is selected. Press the “Enter” button.
Units: English
Select the desired units.
NOTE: English means level in inch and
temperature in °F.
Metric means level in cm and temperature in °C.
Press the “Advance” button to change the units.
Units: Metric
Press the “Enter” button.
Drain 1 : Valve
Drain 2 : None
Select the type of drain valve.
Press “1” to change drain 1 to pump or valve.
Drain 1 : Pump
Drain 2 : None
Press “2” to change drain 2 to pump, valve or none.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
9001889
4
Programming
Press the “Enter” button to select options.
Options :
Press the “Aux Fill” button for auxiliary fill option or
press “Enter” for heating.
Options :
Aux Fill
If heating is selected, the user can fill in the kW of the
electrical heating (example: 9 kW).
Heating : 6 kW
Press “0”, “9”.
Heating : 9 kW
Press “Enter” to select advance mode in run mode yes
or no.
Advance : Yes
Press “Advance” to change between yes and no.
Advance : No
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
9001889
5
Programming
Press “Enter” to set the hysteresis level (level at which
water drops before it senses it must refill).
Level : hyst 2"
If English is selected for units, this value will be in
inches. If Metric is selected for units, this value will be
in cm.
Select between 1 to 9 cm or inches.
Press “Enter” to select the temperature hysteresis
(level at which temperature drops before machine
senses it must reheat).
Temp : hyst 3°F
Spin retries : 5
Address : 0
If English is selected for units, this value will be in °F.
If Metric is selected for units, this value will be in °C.
Select 1 to 9 °C or °F.
Press the “Enter” button to set the spin retries.
Select 1 to 9 spin retries.
Press “Enter” to set the network address of the
machine. If this is not used, press “Enter”.
The address of the machine has to be set if you
network the machine. Each machine should have a
different address.
Enter to save ?
Fill in between 00 and 99.
Press “Enter” to finish the settings.
Press “Enter” to save the settings or press “Stop” to
exit without saving.
Program Cycle 00
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
9001889
6
Programming
NOTE: If chemical hold is off, then supplies 4
through 9 are controlled exactly like supplies 1
through 3. A switch closure/opening between pins 1
and 4 of the COIN header on the output board will
have no effect.
Version of Control
To determine control version, apply power to machine.
Control will display version of control (i.e., 1.15).
Language on Display (Version 1.15 and
later ONLY)
Program Storing Mode
To set a different language on the WE-8 display:
1. Turn key from RUN to PROGRAM.
The WE-8 control is capable of 99 total cycles. One
cycle contains 1 or more steps.
One step is a function of the wash program
(example: heat).
2. Press “Auxiliary”, “2” and “9” to enter set-up
mode.
Choose between the following functions:
3. English will display. Press “Advance” until
desired language displays (French, Italian,
Spanish and German).
Fill:
To fill the machine with water.
Wash action of the machine.
Wash:
Supply:
4. Press “Enter” keypad.
To add detergent to the wash (liquid or
powder).
5. Press “Enter” to advance through set-up mode.
6. Wait until information is saved.
Cooldown: Cool to programmed temperature
7. Turn key from PROGRAM to RUN.
8. Display will read language chosen for all cycles.
Heat:
Soak:
To heat the water.
The wash will be soaked for a
programmed time and a programmed
temperature.
Setup of the Chemical Hold Feature
(Version 1.11 and later ONLY)
Aux:
A relay contact will close for a
programmed time.
At power up, verify that model is at least
version 1.11. Refer to version of Control Section.
Earlier versions do not have this chemical hold
feature.
Spin:
Drain:
To spin the machine for a programmed
time and RPM.
To drain the water from the machine.
Insert key into key switch and turn to Program.
Push the Auxiliary key, the 2 key, and the 9 key
in succession to enter System Program Mode.
Push the Start key 10 times to arrive at the
Chemical hold choice.
Push the Add Cycle/Advance key to toggle the
Chemical hold feature either Yes (on) or No (off).
Push the Start key twice to save changes and exit
System Program Mode.
Turn key switch to Run.
NOTE: If chemical hold is on, then a switch
closure/opening between pins 1 and 4 of the COIN
header on the output board will control supplies 4
through 9. A closure will turn the programmed
supply/ies on and count down the time for the
supply to be on. An opening will turn the
programmed supply/ies off and halt the time for
the supply to be on.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
Example: Warm Low (time limit 5 minutes
30 seconds)
Explanation of the Step Functions
Fill:
Choose between 4 water inlet configurations and
3 water levels.
Step XX Cycle XX
Warm
Water Inlet Configurations:
Cold:
Hot:
Only opens the cold water valve.
Only opens the hot water valve.
Warm: Opens the cold and hot water valves.
Aux Fill: Opens an auxiliary water valve
if installed.
Step XX Cycle XX
Warm Low
Water Levels:
Low:
Med:
High:
Low water level.
Medium water level.
High water level.
Step XX Cycle XX
0 min
The inlet configurations and the fill levels appear on
the keypad, keys 1, 2, 3 and 8.
Step XX Cycle XX
5 min 30 sec
Be sure to select first the inlet configuration and then
the water level.
NOTE: If a fill error occurs, then machine has
2 minutes to finish filling. If after 2 minutes it has
not finished filling, cycle is aborted.
Then you will be asked for the step time limit.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
9001889
8
Programming
It is possible to more accurately control the
Step XX Cycle XX
95°F Low
temperature of water coming in to the machine during
a fill step. This does not apply to “Aux Fill” step. The
control will mix the hot and cold water inlet to the
temperature programmed in the fill function. To fill in
the temperature, select the water inlet type and the
water level. Press the “Heat” button and the control
will ask the temperature. In this way the water inlet
type selected is of no use because the control will mix
between the cold and hot water inlet to reach the
temperature.
Step XX Cycle XX
0 min
Example: Fill to low level and 95°F (step time limit:
5 minutes 30 seconds).
Step XX Cycle XX
5 min 30 sec
Step XX Cycle XX
Warm
Step XX Cycle XX
Warm Low
Step XX Cycle XX
0°F
Step XX Cycle XX
95°F
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
Wash:
Supply:
Choose between 7 different preset wash actions.
Choose between 9 different supplies.
Supply 1: Turns on the water valve in compartment
A of the supply box.
Action
Time (sec) (sec)
Stop Time G-force
Supply 2: Turns on the water valve in compartment
B of the supply box.
Wash 1
Wash 2
Wash 3
Wash 4
Wash 5*
Wash 6
Wash 7
18
3
0.5
0.5
0
3
0
27
0
Supply 3: Turns on the water valve in compartment
C of the supply box.
10
18
4
20
3
0.5
0.5
0.5
0
Supply 4: Activates supply pump 1.
Supply 5: Activates supply pump 2.
Supply 6: Activates supply pump 3.
Supply 7: Activates supply pump 4.
Supply 8: Activates supply pump 5.
Supply 9: Activates supply pump 6.
The Supply button is button 6.
56
0
0
The “Wash” button is button 4 on the display.
Example: Wash 4 for 8 minutes 00 seconds.
Example: Supply 1 and 5 for 20 seconds.
Step XX Cycle XX
Wash
Step XX Cycle XX
Supply
Step XX Cycle XX
Wash 4 10/20
Step XX Cycle XX
Supply
1
5
Step XX Cycle XX
0 min
Step XX Cycle XX
0 min
Step XX Cycle XX
8 min 00 sec
Heat:
Step XX Cycle XX
0 min 20 sec
* Refer to section on Wash 5 Thermal Cool-Down.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
Chemical Hold Feature
Enter time in minutes
and press “Enter”
(example: 5 min).
Chemical supply injection can be paused. Refer to
Setup of Chemical Hold Feature.
Step XX Cycle XX
1 hours 05 min
Wash 5 Thermal Cool-Down
Immediately after a heat step, a temperature-controlled
thermal cool-down may be programmed to prevent
fiber shock from sudden cool-down.
Step XX Cycle XX
Wash
The “Heat” button is number 5.
Example: Heat up to 140°F with the time limit of
45 minutes.
Thermal Cool-Down
is Wash 5.
Step XX Cycle XX
Wash 5
Step XX Cycle XX
Heat
Step XX Cycle XX
0°F (or 0°C)
Step XX Cycle XX
0°F
Enter desired temperature for load to
cool down to. Three digits must be used
for temperature. If Fahrenheit, the valid
temperature range is 80° – 200°F. If
Celcius, valid temperature range is
25° – 90°C (example: 95°F).
Step XX Cycle XX
140°F
Step XX Cycle XX
95°F
Step XX Cycle XX
0 hours
Step XX Cycle XX
0 hours
Step XX Cycle XX
0 hours 45 min
Step XX Cycle XX
1 hours 00 min
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
9001889
11
Programming
Soak:
Example: Soak time of 2 hours with 32°F.
Button 7 is the “Soak” button.
By pressing button 7, “Soak” will appear on the
display. Press “Enter” to fill in the soak time.
Step XX Cycle XX
Soak
Example: Soak for 2 hours.
Step XX Cycle XX
Soak
Step XX Cycle XX
0°F
Use the key pad to fill in
the soak temperature
(example: 32°F).
Step XX Cycle XX
0 hours
Step XX Cycle XX
32°F
Use the key pad to fill in
the hours of the soak time
(example: 2 hours).
Step XX Cycle XX
Soak 32°F
Step XX Cycle XX
2 hours 00 min
Now you can fill in the
minutes (example:
23 minutes).
Step XX Cycle XX
0 hours
Step XX Cycle XX
2 hours 23 min
Use the key pad to fill in
the hours of the soak time
(example: 2 hours).
Press “Enter”.
Step XX Cycle XX
2 hours 00 min
The temperature of the soak will be the temperature
programmed in the previous step. You can also change
the temperature by pressing first “Soak” and then
“Heat”.
Fill in the minutes
(example: 23 minutes).
Step XX Cycle XX
2 hours 23 min
Press “Enter”.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
Spin:
Drain:
Choose between 4 preset spin speeds.
This function drains the water.
If you have 2 drains, select which drain has to be
opened.
18-75
100/135
165
200
Models Models Models Models
Spin 1
RPM
500
650
500
650
800
80
500
650
750
750
Step XX Cycle XX
Drain
Spin 2
RPM
Select Drain 1 or 2.
If you only have 1 drain,
you can only select 1.
Spin 3
RPM
800
Spin 4
RPM
1000
Step XX Cycle XX
Drain 2
“Spin” is button 9.
Step XX Cycle XX
0 min
Step XX Cycle XX
Spin
Enter the drain time
(example: 1 minute
10 seconds).
Select the spin number
(example: 3).
Step XX Cycle XX
1 min 00 sec
Step XX Cycle XX
Spin 3
Step XX Cycle XX
0 min
Step XX Cycle XX
1 min 10 sec
Enter the spin time. Enter
minutes first and then
seconds (example:
5 minutes 30 seconds).
Step XX Cycle XX
NOTE: With the WE-8 control, it is NOT necessary
to program a drain step before spin. The spin step
incorporates the balancing routine and draining
before beginning high speed spin (as a sub part of
the spin step). A programmed drain step will be
skipped if spin step is programmed immediately
after it.
5 min 00 sec
Step XX Cycle XX
5 min 30 sec
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
9001889
13
Programming
Example Making a New Program
Program Cycle 00
Program 51
Step 1: Fill warm water to low level
(5 minutes 30 seconds time limit)
Step 2: Supply 1 and 5 for 20 seconds
Program Cycle 51
Step 3: Heat up to 140°F (45 minutes time limit)
Step 4: Wash action 4 for 8 minutes 00 seconds
Step 5: Drain 1 for 1 minutes 25 seconds
Step 6: Spin 3 for 8 minutes 30 seconds
To program or edit cycles turn the key into the
Program Mode.
Add
Cycle 51
“Program Cycle xx” will be shown on the display.
Step 01
Cycle 51
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
Step 01 Cycle 51
Warm
Step 02 Cycle 51
Supply
Step 01 Cycle 51
Warm Low
Step 02 Cycle 51
Supply
1
5
Step 01 Cycle 51
0 min
Step 02 Cycle 51
0 min
Step 01 Cycle 51
5 min 30 sec
Step 02 Cycle 51
0 min 20 sec
End
Cycle 51
End
Cycle 51
Step 02
Cycle 51
Step 03
Cycle 51
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
Step 03 Cycle 51
Heat
Step 04 Cycle 51
Wash 4 10/20
Step 03 Cycle 51
0°F
Step 04 Cycle 51
0 min
Step 03 Cycle 51
140°F
Step 04 Cycle 51
8 min 00 sec
Step 03 Cycle 51
0 hours
End
Cycle 51
Step 03 Cycle 51
0 hours 45 min
Step 05 Cycle 51
End
Cycle 51
Step 05 Cycle 51
Drain 1
Step 04
Cycle 51
Step 05 Cycle 51
0 min
Step 04 Cycle 51
Wash
Step 05 Cycle 51
1 min 25 sec
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
End
Cycle 51
Enter to save ?
Step 06 Cycle 51
Program Cycle 51
Step 06 Cycle 51
Spin 1
Step 06 Cycle 51
Spin 3
Step 06 Cycle 51
0 min
Step 06 Cycle 51
8 min 30 sec
End
Cycle 51
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming
Edit a Cycle
Program Cycle 00
Change a Complete Step
To edit a cycle enter the cycle number
(example: cycle 51).
Program Cycle 51
Edit
Cycle 51
Press the “Edit Cycle” button.
Name Cycle 51:
Cycle 51
Press the “Enter” button to edit the cycle.
Step 01 Cycle 51
Warm Low
Press “Enter” to continue.
The first step of cycle 51 will display.
Step 02 Cycle 51
Wash 1 18/3
Select the step being edited by using the “Advance”
button to go to the next step or the “Previous” button
to go to the previous step.
If you would like to change the step, press the “Clear”
button.
Step 02 Cycle 51
Wash
Select another wash action or press the “Clear” button
to change the function.
Step 02 Cycle 51
Fill in the function desired (example: soak for 1 hour
30 minutes).
Press the “Soak” button.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
9001889
18
Programming
Step 02 Cycle 51
Soak
Step 02 Cycle 51
0 hours
Step 02 Cycle 51
1 hours 00 min
Step 02 Cycle 51
1 hours 30 min
Step 03 Cycle 51
XXXXXXXX
The control is then in the next step of cycle 51. Press
“Advance” until the display shows “End Cycle 55”.
End
Cycle
Press “Enter” to confirm.
Enter to save ?
Press “Enter” to save or “Stop” to ignore the changes.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
9001889
19
Programming
Changing the Time of a Step
Program Cycle 00
To edit a cycle, enter the cycle number
(example: cycle 51).
Program Cycle 51
Press the “Edit Cycle” button.
Edit
Cycle 51
Press the “Enter” button to edit the cycle.
Name Cycle 51:
Cycle 51
Press “Enter” to continue.
The first step of cycle 51 will display.
Step 01 Cycle 51
Warm Low
Select the step being edited by using the “Advance”
button to go to the next step or the “Previous” button
to go to the previous step.
Step 02 Cycle 51
Wash 1 18/3
Press “Enter” to change the time of the wash action.
Step 02 Cycle 51
5 min 00 sec
Press “Clear” to change the time.
Step 01 Cycle 51
5 min
Fill in another time (example: 6 minutes 20 seconds).
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
9001889
20
Programming
Step 02 Cycle 51
6 min 00 sec
Step 02 Cycle 51
6 min 20 sec
Press “Enter” to go to the next step.
Step 03 Cycle 51
XXXXXXX
Press the “Advance” button until display shows “End
Cycle 51”.
End
Cycle 51
Press “Enter” to confirm.
Enter to save ?
Press “Enter” to save or “Stop” to ignore the changes.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
9001889
21
Programming
Delete a Step
Program Cycle 00
To edit a cycle, enter the cycle number
(example: cycle 51).
Program Cycle 51
Press the “Edit Cycle” button.
Edit
Cycle 51
Press the “Enter” button to edit the cycle.
Name Cycle 51:
Cycle 51
Press “Enter” to continue.
The first step of cycle 51 will display.
Step 01 Cycle 51
Warm Low
Select the step being edited by using the “Advance”
button to go to the next step or the “Previous” button
to go to the previous step.
Step 02 Cycle 51
Wash 1 18/3
Press the “Clear” button to change the step.
Press the “Clear” button again.
Step 02 Cycle 51
Wash
Step 02 Cycle 51
Press the “Clear” button once more.
Step deleted
The step is deleted. Press the “Advance” button to end
cycle 51 and press “Enter” 2 times to save the settings.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
9001889
22
Programming
Insert a Step
Program Cycle 00
To edit a cycle, enter the cycle number
(example: cycle 51).
Program Cycle 51
Press the “Edit Cycle” button.
Edit
Cycle 51
Press the “Enter” button to edit the cycle.
Name Cycle 51:
Cycle 51
Press “Enter” to continue.
The first step of cycle 51 will display.
Step 01 Cycle 51
Warm Low
Select the position where you would like to add a step
by using the “Advance” button to go to the next step or
the “Previous” button to go to the previous step.
Step 02 Cycle 51
Wash 1 18/3
Push the “Add Step” button to add a step.
The control will insert a step before the step selected.
Select the function (example: supply).
Step 02 Cycle 51
Step 02 Cycle 51
Supply
Press the supply number (example: supply 7).
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
9001889
23
Programming
Step 02 Cycle 51
Supply
7
Press “Enter” to confirm.
Step 02 Cycle 51
0 min
Enter the time to activate the supply
(example: 0 minutes 23 seconds).
Step 02 Cycle 51
0 min 00 sec
Step 02 Cycle 51
0 min 23 sec
Press “Enter” to confirm.
Step 03 Cycle 51
Wash 1 18/3
Press the “Advance” button until
“End Cycle 51” is displayed.
End Cycle 51
Press “Enter” to confirm.
Enter to save ?
Press “Enter” to save or “Stop” to ignore the changes.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
9001889
24
Programming
Delete a Cycle
Program Cycle 00
Press the “Erase Cycle” button.
Erase Cycle 00
Erase Cycle 55
Enter to save ?
Press the number of the cycle being erased
(example: 55).
Press “Enter” to confirm.
Press “Enter” to save or “Stop” to ignore the changes.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
9001889
25
Programming
Reloading Previous Settings
This special function allows previous settings to be
restored.
Program Cycle 00
Press “Auxiliary”, “3”, “0”.
Enter to reload
earlier settings
The control will ask if earlier settings are desired.
Press “Enter” to confirm the settings.
NOTE: This function only goes back to the last
programming function entered.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
9001889
26
Programming
Cycle Count
Reading Cycle Count
Program Cycle xx
1. Enter Program Mode by turning key to
PROGRAM position (xx represents a cycle
number from 00 to 99).
PROGRAM
RUN
Program Cycle xx
2. Press “Auxiliary” key, then “3” key, then “1” key.
Total Working
Hours 347
3. The total hours of cycle operation (actual run
time) will display. Press “Advance” key to
continue.
Example display shows 347 total hours (of all
cycles).
4. Display now shows total cycle count. Press
“Advance” key to continue into calibration
mode, or press “Clear/Stop” key to exit.
Total Cycle : 5
Example display shows 5 total cycles have been
run.
OR...
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
9001889
27
Programming
Calibration of the Machine
The _x__PV should reflect the size selected in earlier
steps.
Turn key to Program Mode.
Program Cycle 00
Press “Auxiliary”, “3”, “1”.
Total working
hours : 0
The total hours the machine was running will be
displayed.
Press “Advance” and screen will show total cycles.
Press “Advance” to calibrate the water level sensor.
level : 0.0 “
Enter to zero
If the value is not zero, press “Enter” and the value
will change to zero.
Press “Advance” to calibrate the motor.
Spin
XXX rpm
The board will lock the door and let the motor spin at
approximately 500 rpm (Firmware version 1.12 or
higher). The rpm will increase on the display. If the
machine reached approximately 500 rpm, the display
will show a reference value.
Reference x.xx
After the reference value is shown, the machine will
coast down to stop. When the machine stands still, the
board will unlock the door.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
9001889
28
Programming
Speed Calibration
Calibrate 2
500 rpm
This function automatically calibrates water level,
distribution speed and spin speed.
Ref: #
Offset: #
Total working
hours : #
Coast down
Please wait
Program Cycle #
Total Cycle:
#
End of Calibration
Calibration
and testing
level: 0.0"
Enter to zero
If shell is empty of
water and display reads
0.0", then press “Add
Cycle/Advance”.
Motor Control
Distribute Speed
# rpm
Spin
# rpm
Calibrate 1
100 rpm
Spin
# rpm
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Download from Www.Somanuals.com. All Manuals Search And Download.
9001889
29
Pre-Programmed Cycles
Cycle 01
Sheets Light Soil
Cycle 02
Sheets No Bleach
Step
1
Description
Min:sec
5:00
0:45
7:00
1:00
5:00
2:00
1:00
1:00
5:00
0:30
4:00
1:00
3:00
Step
1
Description
Min:sec
5:00
0:45
7:00
1:00
5:00
2:00
1:00
1:00
5:00
0:30
4:00
1:00
3:00
Hot Fill to Low Level
Hot Fill to Low Level
2
Supply 1, 2, 4, 5
Wash 1 18/3 (32°F)
Drain 1
2
Supply 1, 4
3
3
Wash 1 18/3 (32°F)
Drain 1
4
4
5
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
5
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
6
6
7
7
8
Spin 1
8
Spin 1
9
100°F Fill to Low Level
Supply 3, 6, 7
Wash 1 18/3 (32°F)
Drain 1
9
100°F Fill to Low Level
Supply 3, 6, 7
Wash 1 18/3 (32°F)
Drain 1
10
11
12
13
10
11
12
13
Spin 1
Spin 1
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Programmed Cycles
Cycle 03
Towels Light Soil
Cycle 04
Towels No Bleach
Step
1
Description
Min:sec
5:00
0:45
7:00
1:00
5:00
2:00
1:00
1:00
5:00
0:30
5:00
1:00
6:00
Step
1
Description
Min:sec
5:00
0:45
7:00
1:00
5:00
2:00
1:00
1:00
5:00
0:30
4:00
1:00
6:00
Hot Fill to Low Level
Hot Fill to Low Level
2
Supply 1, 2, 4, 5
Wash 1 18/3 (32°F)
Drain 1
2
Supply 1, 4
3
3
Wash 1 18/3 (32°F)
Drain 1
4
4
5
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
5
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
6
6
7
7
8
Spin 1
8
Spin 1
9
110°F Fill to Low Level
Supply 3, 6, 7
Wash 1 18/3 (32°F)
Drain 1
9
110°F Fill to Low Level
Supply 3, 6, 7
Wash 1 18/3 (32°F)
Drain 1
10
11
12
13
10
11
12
13
Spin 4
Spin 4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Programmed Cycles
Cycle 05
Sheets Medium Soil
Cycle 06
Towels Medium Soil
Step
1
Description
Min:sec
5:00
0:45
6:00
1:00
5:00
0:45
6:00
1:00
5:00
2:00
1:00
1:00
5:00
0:30
4:00
1:00
3:00
Step
1
Description
Min:sec
5:00
Hot Fill to Low Level
Hot Fill to Low Level
2
Supply 1, 4
2
Supply 1, 4
0:45
6:00
1:00
5:00
0:45
6:00
1:00
5:00
2:00
1:00
1:00
5:00
0:30
4:00
1:00
6:00
3
Wash 1 18/3 (32°F)
Drain 1
3
Wash 1 18/3 (32°F)
Drain 1
4
4
5
Hot Fill to Low Level
Supply 2, 5
5
Hot Fill to Low Level
Supply 2, 5
6
6
7
Wash 1 18/3 (32°F)
Drain 1
7
Wash 1 18/3 (32°F)
Drain 1
8
8
9
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
9
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
10
11
12
13
14
15
16
17
10
11
12
13
14
15
16
17
Spin 1
Spin 1
100°F Fill to Low Level
Supply 3, 6, 7
Wash 1 18/3 (32°F)
Drain 1
110°F Fill to Low Level
Supply 3, 6, 7
Wash 1 18/3 (32°F)
Drain 1
Spin 1
Spin 4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Programmed Cycles
Cycle 07
Blankets Warm
Cycle 08
Spreads Cold
Step
1
Description
Warm Fill to High Level
Supply 1, 4
Min:sec
5:00
0:45
6:00
1:00
5:00
5:00
1:00
1:00
5:00
0:30
4:00
1:00
4:00
Step
1
Description
Min:sec
5:00
0:45
6:00
1:00
5:00
1:30
1:00
1:00
5:00
0:30
4:00
1:00
4:00
Cold Fill to High Level
Supply 1, 4
2
2
3
Wash 1 18/3 (32°F)
Drain 1
3
Wash 2 3/27 (32°F)
Drain 1
4
4
5
Warm Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
5
Cold Fill to High Level
Wash 2 3/27 (32°F)
Drain 1
6
6
7
7
8
Spin 1
8
Spin 1
9
Warm Fill to Low Level
Supply 3, 6, 7
9
Cold Fill to High Level
Supply 3, 6, 7
Wash 2 3/27 (32°F)
Drain 1
10
11
12
13
10
11
12
13
Wash 2 3/27 (32°F)
Drain 1
Spin 4
Spin 4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Programmed Cycles
Cycle 09
Towels Heavy Soil
Cycle 10
Rinse and Spin
Step
1
Description
Min:sec
5:00
0:45
7:00
5:00
1:00
7:00
1:00
1:00
5:00
2:00
1:00
1:00
5:00
1:00
4:00
1:00
6:00
Step
Description
Warm Fill to Low Level
Wash 1 18/3 (32°F)
Drain 1
Min:sec
5:00
Hot Fill to Low Level
1
2
3
4
5
2
Supply 1, 4
1:00
3
Wash 1 18/3 (32°F)
Hot Fill to High Level
Supply 2, 5
1:00
4
Spin 1
1:00
5
Spin 4
4:00
6
Wash 1 18/3 (32°F)
Drain 1
7
8
Spin 1
9
Warm Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
10
11
12
13
14
15
16
17
Spin 1
Warm Fill to Low Level
Supply 3, 6, 7
Wash 1 18/3 (32°F)
Drain 1
Spin 4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Programmed Cycles
Cycle 11
Health Care Sheets Light Soil
Cycle 12
Health Care Towels Light Soil
Step
1
Description
Warm Fill to High Level
Wash 1 18/3 (32°F)
Drain 1, 2, 4, 5
Hot Fill to Low Level
Supply 1, 2
Min:sec
5:00
2:00
1:00
5:00
0:45
8:00
1:00
5:00
3:00
1:00
1:00
5:00
0:30
4:00
1:00
4:00
Step
1
Description
Min:sec
5:00
2:00
1:00
5:00
0:45
8:00
1:00
5:00
3:00
1:00
1:00
5:00
0:30
4:00
1:00
4:00
Warm Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
2
2
3
3
4
4
Hot Fill to Low Level
Supply 1, 2, 4, 5
Wash 1 18/3 (32°F)
Drain 1
5
5
6
Wash 1 18/3 (32°F)
Drain 1
6
7
7
8
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
8
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
9
9
10
11
12
13
14
15
16
10
11
12
13
14
15
16
Spin 1
Spin 1
100°F Fill to Low Level
Supply 3, 6, 7
110°F Fill to Low Level
Supply 3, 6, 7
Wash 1 18/3 (32°F)
Drain 1
Wash 1 18/3 (32°F)
Drain 1
Spin 1
Spin 4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Programmed Cycles
Cycle 13
Health Care Sheets Heavy Soil
Cycle 14
Health Care Towels Heavy Soil
Step
1
Description
Min:sec
5:00
2:00
1:00
5:00
2:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
1:00
5:00
0:30
4:00
1:00
3:00
Step
1
Description
32°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Min:sec
5:00
2:00
1:00
5:00
2:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
1:00
5:00
0:30
4:00
1:00
6:00
32°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
2
2
3
3
4
120°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1, 4
4
120°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
5
5
6
6
7
Hot Fill to Low Level
Supply 1
7
Hot Fill to Low Level
Supply 1, 4
8
8
9
Wash 1 18/3 (32°F)
Drain 1
9
Wash 1 18/3 (32°F)
Drain 1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Hot Fill to Low Level
Supply 2, 5
Hot Fill to Low Level
Supply 2, 5
Wash 1 18/3 (32°F)
Drain 1
Wash 1 18/3 (32°F)
Drain 1
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Spin 1
Spin 1
100°F Fill to Low Level
Supply 3, 6, 7
110°F Fill to Low Level
Supply 3, 6, 7
Wash 1 18/3 (32°F)
Drain 1
Wash 1 18/3 (32°F)
Drain 1
Spin 1
Spin 4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Programmed Cycles
Cycle 15
Health Care Cotton Blankets
Cycle 16
Health Care Diapers Heavy Soil
Step
1
Description
110°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Min:sec
5:00
2:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
1:00
5:00
0:30
4:00
1:00
6:00
Step
1
Description
32°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Min:sec
5:00
2:00
1:00
5:00
2:00
1:00
5:00
0:45
7:00
1:00
5:00
0:30
7:00
1:00
5:00
0:30
7:00
1:00
5:00
4:00
1:00
2:00
5:00
2:00
1:00
5:00
0:30
4:00
1:00
1:00
6:00
2
2
3
3
4
Hot Fill to Low Level
Supply 1, 2, 4, 5
Wash 1 18/3 (32°F)
Drain 1
4
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
5
5
6
6
7
7
Hot Fill to Low Level
Supply 1, 4
8
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
8
9
9
Wash 1 18/3 (32°F)
Drain 1
10
11
12
13
14
15
16
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Spin 1
Hot Fill to Low Level
Supply 1, 4
110°F Fill to Low Level
Supply 3, 6, 7
Wash 1 18/3 (32°F)
Drain 1
Wash 1 18/3 (32°F)
Drain 1
Hot Fill to Low Level
Supply 2, 5
Spin 4
Wash 1 18/3 (32°F)
Drain 1
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Spin 1
110°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
110°F Fill to Low Level
Supply 3, 6, 7
Wash 1 18/3 (32°F)
Drain 1
Spin 1
Spin 4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Programmed Cycles
Cycle 17
Health Care Personal Bleach
Cycle 18
Health Care Personal No Bleach
Step
1
Description
Min:sec
5:00
0:45
6:00
1:00
5:00
2:00
1:00
1:00
5:00
0:30
4:00
1:00
3:00
Step
1
Description
Hot Fill to Low Level
Supply 1, 4
Min:sec
Hot Fill to Low Level
Supply 1, 2, 4, 5
Wash 1 18/3 (32°F)
Drain 1
5:00
0:45
6:00
1:00
5:00
2:00
1:00
1:00
5:00
0:30
4:00
1:00
3:00
2
2
3
3
Wash 1 18/3 (32°F)
Drain 1
4
4
5
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
5
110°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
6
6
7
7
8
Spin 1
8
Spin 1
9
110°F Fill to Low Level
Supply 3, 6, 7
9
110°F Fill to Low Level
Supply 3, 6, 7
Wash 1 18/3 (32°F)
Drain 1
10
11
12
13
10
11
12
13
Wash 1 18/3 (32°F)
Drain 1
Spin 1
Spin 1
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Programmed Cycles
Cycle 19
Health Care Pads Polyester
Cycle 20
Table Linen Iron
Step
1
Description
110°F Fill to Low Level
Supply 1, 4
Min:sec
5:00
0:45
3:00
5:00
2:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
1:00
5:00
2:00
1:00
1:00
5:00
0:30
3:00
1:00
4:00
Step
1
Description
Min:sec
5:00
2:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
1:00
5:00
0:30
2:00
0:30
5:00
1:00
4:00
110°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
2
2
3
Wash 1 18/3 (32°F)
130°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
3
4
4
Hot Fill to Low Level
Supply 1, 4
5
5
6
6
Wash 1 18/3 (32°F)
Drain 1
7
Hot Fill to Low Level
Supply 1, 4
7
8
8
Hot Fill to Low Level
Supply 2, 5
9
Wash 1 18/3 (32°F)
Drain 1
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
10
11
12
13
14
15
16
17
18
19
20
21
22
Wash 1 18/3 (32°F)
Drain 1
Hot Fill to Low Level
Supply 2, 5
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Wash 1 18/3 (32°F)
Drain 1
Spin 1
Spin 1
110°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
110°F Fill to Low Level
Supply 3, 6
Wash 1 18/3 (32°F)
Supply 6, 8
Spin 1
110°F Fill to Low Level
Supply 3, 6, 7
Wash 1 18/3 (32°F)
Drain 1
Wash 1 18/3 (32°F)
Drain 1
Spin 2
Spin 4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Programmed Cycles
Cycle 21
Table Linen No Iron
Cycle 22
Table Color Iron
Step
1
Description
Min:sec
5:00
2:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
1:00
5:00
0:30
4:00
1:00
3:00
Step
1
Description
110°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Min:sec
5:00
2:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
1:00
5:00
0:30
4:00
0:30
5:00
1:00
4:00
110°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
2
2
3
3
4
Hot Fill to Low Level
Supply 1, 4
4
Hot Fill to Low Level
Supply 1, 4
5
5
6
Wash 1 18/3 (32°F)
Drain 1
6
Wash 1 18/3 (32°F)
Drain 1
7
7
8
Hot Fill to Low Level
Supply 2, 5
8
Hot Fill to Low Level
Supply 1, 4
9
9
10
11
12
13
14
15
16
17
18
19
20
Wash 1 18/3 (32°F)
Drain 1
10
11
12
13
14
15
16
17
18
19
20
21
22
Wash 1 18/3 (32°F)
Drain 1
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Spin 1
Spin 1
110°F Fill to Low Level
Supply 3, 6, 7
110°F Fill to Low Level
Supply 3, 6
Wash 1 18/3 (32°F)
Drain 1
Wash 1 18/3 (32°F)
Supply 8
Spin 1
Wash 1 18/3 (32°F)
Drain 1
Spin 2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Programmed Cycles
Cycle 23
Table Color No Iron
Cycle 24
Visa Iron
Step
1
Description
110°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Min:sec
5:00
2:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
1:00
5:00
0:30
4:00
1:00
4:00
Step
1
Description
Min:sec
5:00
3:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
1:00
5:00
2:00
1:00
5:00
0:30
2:00
0:30
5:00
1:00
3:00
110°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
2
2
3
3
4
Hot Fill to Low Level
Supply 1, 4
4
Hot Fill to Low Level
Supply 1, 4
5
5
6
Wash 1 18/3 (32°F)
Drain 1
6
Wash 1 18/3 (32°F)
Drain 1
7
7
8
Hot Fill to Low Level
Supply 1, 4
8
Hot Fill to Low Level
Supply 2, 5
9
9
10
11
12
13
14
15
16
17
18
19
20
Wash 1 18/3 (32°F)
Drain 1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Wash 1 18/3 (32°F)
Drain 1
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Spin 1
Spin 1
110°F Fill to Low Level
Supply 3, 6, 7
Wash 1 18/3 (32°F)
Drain 1
110°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
110°F Fill to Low Level
Supply 3, 6
Spin 1
Wash 1 18/3 (32°F)
Supply 8
Wash 1 18/3 (32°F)
Drain 1
Spin 2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Programmed Cycles
Cycle 25
Visa No Iron
Cycle 26
Visa Color Iron
Step
1
Description
Min:sec
5:00
3:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
1:00
5:00
2:00
1:00
5:00
0:30
4:00
1:00
3:00
Step
1
Description
110°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1, 4
Min:sec
5:00
3:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
1:00
5:00
2:00
1:00
5:00
0:30
2:00
0:30
4:00
1:00
3:00
110°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
2
2
3
3
4
Hot Fill to Low Level
Supply 1, 4
4
Hot Fill to Low Level
Supply 1
5
5
6
Wash 1 18/3 (32°F)
Drain 1
6
Wash 1 18/3 (32°F)
Drain 1
7
7
8
Hot Fill to Low Level
Supply 2, 5
8
Hot Fill to Low Level
Supply 1, 4
9
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Wash 1 18/3 (32°F)
Drain 1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Wash 1 18/3 (32°F)
Drain 1
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Spin 1
Spin 1
110°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
110°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
110°F Fill to Low Level
Supply 3, 6
110°F Fill to Low Level
Supply 3, 6
Wash 1 18/3 (32°F)
Drain 1
Wash 1 18/3 (32°F)
Supply 8
Spin 1
Wash 1 18/3 (32°F)
Drain 1
Spin 2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Programmed Cycles
Cycle 27
Visa Color No Iron
Cycle 28
Shirt Color Starch
Step
1
Description
110°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Min:sec
5:00
3:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
1:00
5:00
2:00
1:00
5:00
0:30
4:00
1:00
3:00
Step
1
Description
Min:sec
5:00
0:45
7:00
1:00
5:00
0:45
5:00
1:00
5:00
3:00
1:00
1:00
5:00
0:30
0:30
4:00
1:00
3:00
Hot Fill to Low Level
2
2
Supply 1, 4
3
3
Wash 1 18/3 (32°F)
Drain 1
4
Hot Fill to Low Level
Supply 1, 4
4
5
5
Hot Fill to Low Level
Supply 1, 4
6
Wash 1 18/3 (32°F)
Drain 1
6
7
7
Wash 1 18/3 (32°F)
Drain 1
8
Hot Fill to Low Level
Supply 1, 4
8
9
9
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Wash 1 18/3 (32°F)
Drain 1
10
11
12
13
14
15
16
17
18
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Spin 1
Cold Fill to High Level
Supply 3, 6
Spin 1
Supply 5
110°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Wash 1 18/3 (32°F)
Drain 1
Spin 2
110°F Fill to Low Level
Supply 3, 6
Wash 1 18/3 (32°F)
Drain 1
Spin 1
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Programmed Cycles
Cycle 29
Shirt Bleach Starch
Cycle 30
Shirt Color No Bleach
Step
1
Description
Min:sec
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
1:00
5:00
0:30
0:30
4:00
1:00
3:00
Step
1
Description
Min:sec
5:00
0:45
7:00
1:00
5:00
0:45
5:00
1:00
5:00
3:00
1:00
1:00
5:00
0:30
0:30
4:00
1:00
3:00
Hot Fill to Low Level
Hot Fill to Low Level
2
Supply 1, 4
2
Supply 1, 4
3
Wash 1 18/3 (32°F)
Drain 1
3
Wash 1 18/3 (32°F)
Drain 1
4
4
5
Hot Fill to Low Level
Supply 2, 5
5
Hot Fill to Low Level
Supply 1, 4
6
6
7
Wash 1 18/3 (32°F)
Drain 1
7
Wash 1 18/3 (32°F)
Drain 1
8
8
9
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
9
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
10
11
12
13
14
15
16
17
18
10
11
12
13
14
15
16
17
18
Spin 1
Spin 1
Cold Fill to High Level
Supply 3, 6
Cold Fill to High Level
Supply 3, 6
Supply 2, 8
Supply 4
Wash 1 18/3 (32°F)
Drain 1
Wash 1 18/3 (32°F)
Drain 1
Spin 2
Spin 2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Programmed Cycles
Cycle 31
Shirt Delicate
Cycle 32
Starch Extract
Step
1
Description
Warm Fill to Low Level
Wash 2 3/27 (32°F)
Drain 1
Min:sec
5:00
2:00
1:00
5:00
0:45
5:00
1:00
5:00
2:00
1:00
5:00
2:00
1:00
5:00
0:30
0:30
3:00
1:00
1:30
Step
Description
Min:sec
5:00
1
2
3
4
5
Warm Fill to Low Level
Supply 2, 8
2
0:30
3
Wash 1 18/3 (32°F)
Drain 1
7:00
4
Warm Fill to Low Level
Supply 1, 4
1:00
5
Spin 2
3:00
6
Wash 2 3/27 (32°F)
Drain 1
7
8
Warm Fill to High Level
Wash 2 3/27 (32°F)
Drain 1
9
10
11
12
13
14
15
16
17
18
19
Warm Fill to High Level
Wash 2 3/27 (32°F)
Drain 1
Cold Fill to High Level
Supply 3, 6, 7
Supply 4
Wash 2 3/27 (32°F)
Drain 1
Spin 2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Programmed Cycles
Cycle 33
Uniforms Bleach
Cycle 34
Uniforms No Bleach
Step
1
Description
Min:sec
5:00
3:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
1:00
5:00
2:00
1:00
5:00
0:30
4:00
1:00
3:00
Step
1
Description
Min:sec
5:00
0:45
6:00
1:00
5:00
2:00
1:00
1:00
5:00
0:30
4:00
1:00
3:00
110°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Hot Fill to Low Level
2
2
Supply 1, 4
3
3
Wash 1 18/3 (32°F)
Drain 1
4
Hot Fill to Low Level
Supply 1, 4
4
5
5
110°F Fill to Low Level
Wash 1 18/3 (32°F)
Drain 1
6
Wash 1 18/3 (32°F)
Drain 1
6
7
7
8
Hot Fill to Low Level
Supply 2, 5
8
Spin 1
9
9
110°F Fill to Low Level
Supply 3, 6, 7
Wash 1 18/3 (32°F)
Drain 1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Wash 1 18/3 (32°F)
Drain 1
10
11
12
13
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Spin 1
Spin 1
110°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
110°F Fill to Low Level
Supply 3, 6, 7
Wash 1 18/3 (32°F)
Drain 1
Spin 1
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Programmed Cycles
Cycle 35
Rags Heavy Soil
Cycle 36
Mops in Bags
Step
1
Description
110°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Min:sec
5:00
2:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
2:00
1:00
1:00
5:00
0:30
4:00
1:00
6:00
Step
1
Description
Min:sec
5:00
2:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
2:00
1:00
1:00
5:00
0:30
4:00
1:00
4:00
110°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
2
2
3
3
4
Hot Fill to Low Level
Supply 1, 4
4
Hot Fill to Low Level
Supply 1, 4
5
5
6
Wash 1 18/3 (32°F)
Drain 1
6
Wash 1 18/3 (32°F)
Drain 1
7
7
8
Hot Fill to Low Level
Supply 2, 5
8
Hot Fill to Low Level
Supply 2, 5
9
9
10
11
12
13
14
15
16
17
18
19
20
Wash 1 18/3 (32°F)
Drain 1
10
11
12
13
14
15
16
17
18
19
20
Wash 1 18/3 (32°F)
Drain 1
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Spin 1
Spin 1
110°F Fill to Low Level
Supply 3, 6
110°F Fill to Low Level
Supply 3, 6
Wash 1 18/3 (32°F)
Drain 1
Wash 1 18/3 (32°F)
Drain 1
Spin 4
Spin 4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Programmed Cycles
Cycle 37
Rewash/Reclaim
Cycle 38
Supply Setup
Step
1
Description
Min:sec
5:00
2:00
1:00
5:00
0:45
4:00
1:00
5:00
0:45
7:00
1:00
5:00
4:00
1:00
1:00
5:00
2:00
1:00
5:00
0:30
4:00
0:30
4:00
1:00
4:00
Step
1
Description
Warm Fill to Low Level
Supply 1
Min:sec
5:00
2:00
2:00
2:00
2:00
2:00
1:00
5:00
2:00
2:00
2:00
2:00
0:30
1:00
130°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
2
2
3
3
Supply 2
4
Hot Fill to Low Level
Supply 1, 2, 4, 5
Wash 1 18/3 (32°F)
Drain 1
4
Supply 3
5
5
Supply 4
6
6
Supply 5
7
7
Drain 1
8
Hot Fill to Low Level
Supply 1, 2, 4, 5
Wash 1 18/3 (32°F)
Drain 1
8
Warm Fill to Low Level
Supply 6
9
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
10
11
12
13
14
Supply 7
Supply 8
Hot Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Supply 9
Wash 1 18/3 (32°F)
Drain 1
Spin 1
110°F Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
110°F Fill to High Level
Supply 3, 6
Wash 1 18/3 (32°F)
Supply 3, 6
Wash 1 18/3 (32°F)
Drain 1
Spin 4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Programmed Cycles
Cycle 39
Test Program
Cycle 39
Test Program
Step
1
Description
Cold Fill to High Level
Drain 1
Min:sec
0:30
0:10
5:00
5:00
1h00
5:00
0:30
0:30
0:30
0:30
0:30
1:00
0:30
0:30
0:30
0:30
0:30
0:30
0:30
0:30
0:30
1:00
0:05
0:05
0:05
5:00
5:00
2h00
1:00
2:00
2:00
2:00
2:00
0:15
5:00
Step
36
Description
Min:sec
0:15
Wash 1 18/3 (32°F)
Drain 1
2
37
1:00
3
Hot Fill to Low Level
Auxiliary Fill to Med Level
Heat (150°F)
Cold Fill to High Level
Supply 1
4
5
6
7
8
Supply 2
9
Supply 3
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
Supply 4
Supply 5
Drain 1
Warm Fill to Low Level
Supply 6
Supply 7
Supply 8
Supply 9
Wash 2 3/27 (32°F)
Wash 3, no agitation (32°F)
Wash 4 10/3 (32°F)
Wash 1, no reverse (32°F)
Drain 1
Auxiliary 1
Auxiliary 2
Auxiliary 3
150°F Fill to High Level
Cold Fill to Overflow
Soak (150°F)
Drain 1
Spin 1
Spin 2
Spin 3
Spin 4
Auxiliary 3
Cold Fill to Med Level
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Programmed Cycles
Cycle 40
Energy Hot
Cycle 41
Energy Warm
Step
1
Description
Min:sec
5:00
0:15
4:00
1:00
5:00
2:00
1:00
5:00
0:15
2:00
3:00
Step
1
Description
Warm Fill to Low Level
Supply 1, 2
Min:sec
5:00
0:15
4:00
1:00
5:00
2:00
1:00
5:00
0:15
2:00
3:00
Hot Fill to Low Level
Supply 1, 2
2
2
3
Wash 1 18/3 (32°F)
Drain 1
3
Wash 1 18/3 (32°F)
Drain 1
4
4
5
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
5
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
6
6
7
7
8
Cold Fill to High Level
Supply 3
8
Cold Fill to High Level
Supply 3
9
9
10
11
Wash 1 18/3 (32°F)
Spin 4
10
11
Wash 1 18/3 (32°F)
Spin 4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Programmed Cycles
Cycle 42
Energy Cold
Cycle 50
Normal 95°C
Step
1
Description
Cold Fill to Low Level
Supply 1, 2
Min:sec
5:00
0:15
4:00
1:00
5:00
2:00
1:00
5:00
0:15
2:00
3:00
Step
1
Description
Min:sec
5:00
0:30
1h00
2:00
1:00
5:00
0:30
1h00
6:00
5:00
2:00
1:00
5:00
2:00
1:00
5:00
2:00
1:00
5:00
2:00
1:00
1:00
5:00
0:30
3:00
1:00
5:00
Warm Fill to Low Level
Supply 1, 4
2
2
3
Wash 1 18/3 (32°F)
Drain 1
3
Heat (104°F)
4
4
Wash 1 18/3 (32°F)
Drain 1
5
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
5
6
6
Hot Fill to Low Level
Supply 1, 2, 4, 5
Heat (203°F)
7
7
8
Cold Fill to High Level
Supply 3
8
9
9
Wash 1 18/3 (32°F)
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
10
11
Wash 1 18/3 (32°F)
Spin 4
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Spin 1
Cold Fill to High Level
Supply 3, 6, 7
Wash 1 18/3 (32°F)
Drain 1
Spin 4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Programmed Cycles
Cycle 51
Normal 60°C
Cycle 52
Normal 40°C
Step
1
Description
Min:sec
5:00
0:30
1h00
2:00
1:00
5:00
0:30
1h00
6:00
5:00
2:00
1:00
5:00
2:00
1:00
5:00
2:00
1:00
5:00
2:00
1:00
1:00
5:00
0:30
3:00
1:00
5:00
Step
1
Description
Warm Fill to Low Level
Supply 1, 4
Min:sec
5:00
0:30
1h00
2:00
1:00
5:00
0:30
1h00
6:00
5:00
2:00
1:00
5:00
2:00
1:00
5:00
2:00
1:00
5:00
2:00
1:00
1:00
5:00
0:30
3:00
1:00
5:00
Warm Fill to Low Level
Supply 1, 4
2
2
3
Heat (104°F)
3
Heat (104°F)
4
Wash 1 18/3 (32°F)
Drain 1
4
Wash 1 18/3 (32°F)
Drain 1
5
5
6
Hot Fill to Low Level
Supply 1, 2, 4, 5
Heat (140°F)
6
Hot Fill to Low Level
Supply 1, 2, 4, 5
Heat (104°F)
7
7
8
8
9
Wash 1 18/3 (32°F)
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
9
Wash 1 18/3 (32°F)
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Spin 1
Spin 1
Cold Fill to High Level
Supply 3, 6, 7
Cold Fill to High Level
Supply 3, 6, 7
Wash 1 18/3 (32°F)
Drain 1
Wash 1 18/3 (32°F)
Drain 1
Spin 4
Spin 4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Programmed Cycles
Cycle 53
Gentle Cold
Cycle 54
Perm Press 95°C
Step
1
Description
Cold Fill to High Level
Supply 1, 4
Min:sec
5:00
0:30
2:00
1:00
5:00
2:00
1:00
1:00
0:30
0:30
3:00
1:00
2:00
Step
1
Description
Min:sec
5:00
0:30
1h00
2:00
1:00
5:00
0:30
1h00
6:00
5:00
2:00
1:00
5:00
2:00
1:00
5:00
2:00
1:00
5:00
2:00
1:00
1:00
5:00
0:30
3:00
1:00
3:00
Warm Fill to Low Level
Supply 1, 4
2
2
3
Wash 2 3/27 (32°F)
Drain 1
3
Heat (104°F)
4
4
Wash 1 18/3 (32°F)
Drain 1
5
Cold Fill to High Level
Wash 2 3/27 (32°F)
Drain 1
5
6
6
Hot Fill to Low Level
Supply 1, 2, 4, 5
Heat (203°F)
7
7
8
Spin 1
8
9
Cold Fill to High Level
Supply 3, 6, 7
Wash 2 3/27 (32°F)
Drain 1
9
Wash 1 18/3 (32°F)
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
10
11
12
13
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Spin 1
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Spin 1
Cold Fill to High Level
Supply 3, 6, 7
Wash 1 18/3 (32°F)
Drain 1
Spin 1
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Programmed Cycles
Cycle 55
Perm Press 60°C
Cycle 56
Perm Press 40°C
Step
1
Description
Min:sec
5:00
0:30
1h00
2:00
1:00
5:00
0:30
1h00
6:00
5:00
2:00
1:00
5:00
2:00
1:00
5:00
2:00
1:00
5:00
2:00
1:00
1:00
5:00
0:30
3:00
1:00
3:00
Step
1
Description
Warm Fill to Low Level
Supply 1, 4
Min:sec
5:00
0:30
1h00
2:00
1:00
5:00
0:30
1h00
6:00
5:00
2:00
1:00
5:00
2:00
1:00
5:00
2:00
1:00
5:00
2:00
1:00
1:00
5:00
0:30
3:00
1:00
3:00
Warm Fill to Low Level
Supply 1, 4
2
2
3
Heat (104°F)
3
Heat (104°F)
4
Wash 1 18/3 (32°F)
Drain 1
4
Wash 1 18/3 (32°F)
Drain 1
5
5
6
Hot Fill to Low Level
Supply 1, 2, 4, 5
Heat (140°F)
6
Hot Fill to Low Level
Supply 1, 2, 4, 5
Heat (140°F)
7
7
8
8
9
Wash 1 18/3 (32°F)
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
9
Wash 1 18/3 (32°F)
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Cold Fill to High Level
Wash 1 18/3 (32°F)
Drain 1
Spin 1
Spin 1
Cold Fill to High Level
Supply 3, 6, 7
Cold Fill to High Level
Supply 3, 6, 7
Wash 1 18/3 (32°F)
Drain 1
Wash 1 18/3 (32°F)
Drain 1
Spin 1
Spin 1
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Pre-Programmed Cycles
Cycle 57
Gentle 30°C
Step
1
Description
Cold Fill to High Level
Supply 1, 4
Min:sec
5:00
0:30
2:00
1:00
5:00
0:30
1h00
3:00
1:00
5:00
2:00
1:00
1:00
1:00
5:00
0:30
3:00
1:00
2:00
2
3
Wash 2 3/27 (32°F)
Drain 1
4
5
Cold Fill to High Level
Supply 1, 2, 4, 5
Heat (86°F)
6
7
8
Wash 2 3/27 (32°F)
Drain 1
9
10
11
12
13
14
15
16
17
18
19
Cold Fill to High Level
Wash 2 3/27 (32°F)
Drain 1
Spin 1
Drain 1
Cold Fill to High Level
Supply 3, 6, 7
Wash 2 3/27 (32°F)
Drain 1
Spin 1
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Inverter Drive Error Codes
Operation
Panel
Indication
Name
Description and NOTES
Check point
Corrective action
Overcurrent
When the inverter output current reaches
Check the motor Repair the wiring.
shut-off during or exceeds approximately 200% of the
cable insulation and
connection for output
acceleration
rated current during acceleration, the
protective circuit is activated to stop the short-circuit/ground
inverter output.
fault.
Overcurrent
When the inverter output current reaches
Check the motor Repair the wiring.
shut-off during or exceeds approximately 200% of the
constant speed rated current during constant speed, the
cable insulation and
connection for output
protective circuit is activated to stop the short-circuit/ground
inverter output.
fault.
Overcurrent
When the inverter output current reaches
Check for sudden
ContactAlliance
speed reduction.
Check the motor
cable insulation and
connection for
output short-circuit/
ground fault.
Laundry Systems’
Customer Service
department.
shut-off during or exceeds approximately 200% of the
deceleration
rated current during deceleration (other
than acceleration or constant speed), the
protective circuit is activated to stop the
inverter output.
Repair the wiring.
Regenerative
overvoltage
If regenerative energy causes the
inverter’s internal main circuit DC voltage the machine is loaded properly to distribute
Check to make sure
Load the machine
shut-off during to reach or exceed the specified value, the properly and that the the load evenly.
acceleration
protective circuit is activated to stop the
inverter output. It may also be activated
by a surge voltage generated in the power
supply system.
load is balanced.
Regenerative
overvoltage
If regenerative energy causes the
inverter’s internal main circuit DC voltage the machine is loaded properly to distribute
Check to make sure
Load the machine
shut-off during to reach or exceed the specified value, the properly and that the the load evenly.
constant speed protective circuit is activated to stop the
inverter output. It may also be activated
by a surge voltage generated in the power
supply system.
load is balanced.
Regenerative
overvoltage
If regenerative energy causes the
inverter’s internal main circuit DC voltage the machine is loaded properly to distribute
Check to make sure
Load the machine
shut-off during to reach or exceed the specifed value, the properly and that the the load evenly.
deceleration or protective circuit is activated to stop the
load is balanced.
stop
inverter output. It may also be activated
by a surge voltage generated in the power
supply system.
Motor overload The electronic overcurrent protection in
Verify that the AC
Contact Alliance
shut-off
the inverter detects motor overheat due to drive’s parameters are Laundry Systems’
(electronic
overcurrent
protection)
overload or reduced cooling capability
due to overload or reduced cooling
capability during constant-speed operation
to stop the inverter output. When a multi-
pole motor or two or more motors are run,
provide a thermal relay in the output side
of the inverter.
correct.
Customer Service
department.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Inverter Drive Error Codes
Operation
Panel
Indication
Name
Inverter
Description and NOTES
Check point
Corrective action
If a current of more than 150% of the rated Verify that the AC
Contact Alliance
overload shut-
off (electronic
overcurrent
output current flows and overcurrent shut- drive’s parameters are Laundry Systems’
off does not occur (200% or less) inverse- correct.
time characteristics cause the electronic
overcurrent protection to be activated to
stop the inverter output in order to protect
the output transistors.
Customer Service
department.
protection)
Note: Resetting the inverter initializes
the internal heat integrating data of the
electronic overcurrent protection.
Fin overheat
If the cooling fin overheats, the overheat
sensor is actuated to stop the inverter
output.
Check for too
Verify that the AC
drive’s parameters are
correct.
high ambient
temperature.
Check for
Contact Alliance
Laundry Systems’
Customer Service
department.
cooling fin clogging
Brake transistor Internal Circuit Error
alarm detection
Contact Alliance
Laundry Systems’
Customer Service
department.
Output side
ground fault
overcurrent
protection
This function stops the inverter output if a Check the motor cable Repair the wiring.
ground fault overcurrent flows due to a
ground fault which occurred in the
insulation and
connection for output
inverter’s output (load) side. Use Pr. 249 short-circuit/ground
“ground fault detection at start” to set
whether the protective function is to be
activated or not. (In the 400V class, the
protective function is always active.)
fault.
External thermal If the external thermal relay designed for Check for motor
relay operation motor overheat protection or the internally overheating.
Load the machine
properly to distribute
the load evenly.
mounted temperature relay in the motor
Check to make sure
switches on (contacts open), the inverter the machine is loaded
output is stopped. If the relay contacts are properly and that the
reset automatically, the inverter will not
restart unless it is reset.
load is balanced.
Stall prevention The running frequency has fallen to 0 with Check the motor for a Verify that the AC
stall prevention activated.
“locked rotor”
condition.
drive’s parameters are
correct.
Contact Alliance
Laundry Systems’
Customer Service
department.
Output phase
failure
This function stops the inverter output if Check the wiring.
one of the three phases (U, V, W) on the Check the motor for a connections.
Tighten the wire
protection
inverter’s output side (load side) results in fault.
open phase.
Replace the
connectors as needed.
Fan fault
For the inverter which contains a cooling Check the cooling
Replace the fan as
needed.
fan, FN appears on the operation panel
when the cooling fan fails.
fan’s operation.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Inverter Drive Error Codes
Operation
Panel
Name
Description and NOTES
Check point
Corrective action
Load the machine
Indication
Stall prevention During acceleration–If a current of more
Check to make sure
the machine is
loaded properly and
that the load is
balanced.
properly to
distribute the load
evenly.
(overcurrent)
than 150% of the rated inverter current
flows in the motor this function stops the
increase in frequency until the overload
current reduces to prevent the inverter
from resulting in overcurrent shut-off.
ContactAlliance
Verify that the AC
Laundry Systems’
Customer Service
department.
drive’s parameters
are correct.
When the overload current has reduces
below 150%, this function increases the
frequency again.
During constant-speed operation–If a
current of more than 150%, this function
lowers the frequency again.
When the overload current has reduces
below 150%, this function increases the
frequency again.
During deceleration–If a current of more
than 150% of the rated inverter current
flows in the motor, this function stops the
decrease in frequency until the overload
current reduces to prevent the inverter
from resulting in overcurrent shut-off.
When the overload current has reduced
below 150%, this function decreases the
frequency again.
Stall prevention During deceleration-If the regenerative
Check to make sure
Load the machine
(overvoltage)
energy of the motor exceeds the brake
the machine is loaded properly to distribute
capability, this function stops the decrease properly and that the the load evenly.
in frequency to prevent overvoltage
shutoff. As soon as the regenerative
energy has reduced, deceleration resumes.
STOP
load is balanced.
PU stop
A stop made by pressing the
key of Check for a stop made Perform operation
RESET
STOP
RESET
the PU has been set in Pr. 75 “PU stop
selection”.
by pressing the
correctly.
key of the operation
panel during external
operation.
This alarm appears if:
Perform operation
correctly.
The RES signal is on;
You attempted to set any parameter
value in the external operation mode;
You attempted to change the operation
mode during operation;
You attempted to set any parameter
value outside its setting range.
You attempted to set any parameter
value during operation (while signal
STF or STR is ON).
You attempted to set any parameter
value while parameter write is being
inhibited in Pr. 77 “parameter write
inhibit selection”.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Inverter Drive Error Codes
Operation
Panel
Indication
Name
Description and NOTES
Check point
Corrective action
Under Voltage
The power supply has fallen below a
specified level.
This fault appears
every time the
machine is powered
down.
Apply the proper
voltage to the
machine.
Check the power
supply voltage.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001889
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|