aiwa
AV-DV500
STEREO RECEIVER
OPERATING INSTRUCTIONS
Precautions
pg. 1
WARNING
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture
"CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL."
Explanation of Graphical Symbols:
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the
user to the presence of uninsulated "dangerous voltage" within the product's inclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Owner's record
For your convenience, record the model number and serial number (you will find them on the rear of your set) in the
space provided below. Please refer to them when you contact your Aiwa dealer in case of difficulty.
Model No.
AV-DV500
Serial No. (Lot No.)
Check your unit and accessories
Download from Www.Somanuals.com. All Manuals Search And Download.
outlet.
3 AC power cord
- When disconnecting the AC power cord, pull it out by the AC power plug. Do not pull the cord itself.
- Never handle the AC power plug with wet hands, as this could result in fire or shock.
- Power cords should be routed to avoid being severely bent, pinched, or walked upon. Pay particular attention to
the cord from the unit to the power socket.
- Avoid overloading AC power plugs and extension cords beyond their capacity, as this could result in fire or shock.
4 Extension cord - To help prevent electric shock, do not use a polarized AC power plug with an extension cord,
receptacle, or other outlet unless the polarized plug can be completely inserted to prevent exposure of the blades of
the plug.
Precautions (cont.) pg. 2
5 When not in use - Unplug the AC power cord form the AC power plug if the unit will not be used for several
months or more. When the cord is plugged in, a small amount of current continues to flow to the unit, even when the
power is turned off.
Outdoor Antenna
1 Power lines - When connecting an outdoor antenna, make sure it is located away from power lines.
2 Outdoor antenna grounding - Be sure the antenna system is properly grounded to provide protection against
unexpected voltage surges or static electricity build-up. Article 810 of the National Electrical Code, ANSI/NFPA 70,
provides information on proper grounding of the mast, supporting structure, and the lead-in wire to the antenna
discharge unit, as well as the size of the grounding unit, connection to grounding terminals, and requirements for
grounding terminals themselves.
Maintenance
Clean the unit only as recommended in the Operating Instructions
Damage Requiring Service
Have the units serviced by a qualified service technician if:
- The AC power cord or plug has been damaged
- Foreign objects or liquid have gotten inside the unit
- The unit has been exposed to rain or water
- The unit does not seem to operate normally
- The unit exhibits a marked change in performance
- The unit has been dropped, or the cabinet has been damaged
Download from Www.Somanuals.com. All Manuals Search And Download.
DO NOT ATTEMPT TO SERVICE THE UNIT YOURSELF
REMOTE CONTROL
Inserting batteries
Detach the battery cover on the rear of the remote control and insert two R6 (size AA) batteries.
When to replace the batteries
The maximum operational distance between the remote control and the sensor on the main unit should be
approximately 5 meters (16 feet). When this distance decreases, replace the batteries with new ones.
Using the remote control
The instructions in this manual refer mainly to the buttons on the main unit. Buttons on the remote control with the
same names as those on the main unit can be used as well.
NOTE
• If the remote control is not going to be used for an extended period of time, remove the batteries to prevent
possible electrolyte leakage.
• The remote control may not operate correctly when:
- The line of sight between the remote control and the remote sensor inside the display window is exposed to
intense light, such as direct sunlight.
- Other remote controls are used nearby (those of a television, etc.
TABLE OF CONTENTS
PRECAUTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
PREPARATIONS
CONNECTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
SETTING THE CLOCK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
SOUND
CUSTOM AUDIO ADJUSTMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
ELECTRONIC GRAPHIC EQUALIZER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
DSP SURROUND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
BASIC OPERATIONS
SELECTION OF AUDIO/VIDEO SOURCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
RECORDING AN AUDIO SOURCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
RADIO RECEPTION
MANUAL TUNING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
DIRECT TUNING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
PRESETTING STATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
DOLBY PRO LOGIC
SELECTING DOLBY PRO LOGIC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
ADJUSTING SPEAKER LEVEL BALANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
TIMER
SETTING THE SLEEP TIMER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL
CARE AND MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
TROUBLESHOOTING GUIDE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
PARTS INDEX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
PREPARATIONS pg. 3
CONNECTIONS
Before connecting the AC cord
The rated voltage of your unit shown on the rear panels is 120 V AC. Check that the rated voltage matches your
local voltage.
IMPORTANT
Connect the speakers, antennas, and all other external equipment first. Then connect the AC cord at the end.
CONNECTING EQUIPMENT
Jacks and plugs of the connecting cord are color-coded as follows:
Red jacks and plugs: For the right channel of audio signals
White jacks and plugs: For the left channel of audio signals
Yellow jacks and plugs: For video signals
NOTE
Insert the plugs fully into the jacks. Loose connections may produce a humming sound or other noise interference.
click for image of connections
PREPARATIONS (cont.) pg. 4
CONNECTING SPEAKERS (1)
Speaker Terminals
Connect front speakers (system A and/or B), a center speaker and surround speakers to the corresponding speaker
terminals on the unit:
- the front speaker cords to the FRONT SPEAKERS terminals
- the center speaker cord to the CENTER SPEAKER terminals
- the surround speaker cords to the SURROUND SPEAKERS terminals.
For more powerful bass, connect a sub woofer with a built-in amplifier to the SUPER WOOFER jack.
Speaker Impedance
• Front and center speakers
The SPEAKER IMPEDANCE SELECTOR on the rear should be set to the position that matches the impedance
value of the front and center speakers.
When using 4 ohm speakers, set the selector to 4Ω. When using 8 ohm speakers, set the selector to 8 Ω. Please
Download from Www.Somanuals.com. All Manuals Search And Download.
unplug the AC cord before setting the selector.
• Surround speakers and super woofer
The SPEAKER IMPEDANCE SELECTOR has no effect on the SURROUND SPEAKERS terminals and the
SUPER WOOFER jack. For the surround speakers and sub woofer, use speakers of 8 ohms or more.
Connecting + to +, - to - terminals
To get the proper sound effect, the speaker terminals on the unit and the speaker should be connected with proper
polarity; the + terminal on the unit should be connected to the + terminal on the speaker (and - to -)
NOTE
• Be sure to connect the speaker cords correctly as shown in the illustration on the right column. Improper
connections can cause short circuits in the SPEAKER (S) terminals.
• Do not leave objects generating magnetism near the speakers.
• When using a sub woofer, select the speaker system A (see page 6). Otherwise no sound can be heard from it.
Download from Www.Somanuals.com. All Manuals Search And Download.
POSITIONING THE SPEAKERS
Position the speakers to make the most of the Dolby Pro Logic or DSP effect (see "DOLBY LOGIC")
a) Front speakers
b) Center speaker
Position in the center of the two front speakers. In addition, position on or below the TV set, if connecting a TV set
to the unit.
c) Surround Speakers
Place the surround speakers directly to the side of or slightly behind the listening area. Align them horizontally,
Download from Www.Somanuals.com. All Manuals Search And Download.
about 1 meter (3.2 feet) above ear height.
NOTE
Sound is heard from the center speaker mainly when the 5 CH surround or DOLBY PRO LOGIC is set on. Note that
when you select the PHANTOM mode of the DOLBY PROG LOGIC, the center speaker is muted. (For details, see
"DOLBY PRO LOGIC").
PREPARATIONS (cont.) pg. 5
CONNECTING THE SUPPLIED ANTENNAS (2)
Connect the FM antenna to the FM 75 Ω terminals and the AM antenna to the AM LOOP terminals.
To stand the AM loop antenna on a surface
Fix the claw to the slot as shown in the illustration.
Download from Www.Somanuals.com. All Manuals Search And Download.
To position the antennas
FM feeder antenna:
Extend this antenna horizontally in a T shape and fix its ends to the wall.
AM loop antenna:
Position for the best reception.
NOTE
• Do not bring the FM antenna near metal objects or curtain rails.
• Do not bring the AM antenna near other external equipment, the unit itself, the AC power cord or speaker cords, as
noise will be picked up.
• Do not unwind the AM loop antenna wire.
CONNECTING AN OUTDOOR ANTENNA
For better FM reception, use of an outdoor antenna is recommended. Connect the outdoor antenna to the FM ohm
terminals.
TO CONNECT THE AIWA DVD PLAYER XD-DV500
Connect the output terminals of the DVD player to the input terminals of the receiver as follows:
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE
• In this connection, the SUB WOOFER LINE OUT terminal on the DVD player does not need to be connected to
the receiver.
• In the initial settings of the DVD player, set the SUBWOOFER mode of SETUP SPEAKERS to OFF. For details,
see the initial settings in the instruction manual of the DVD player.
PREPARATIONS (cont.) pg. 6
BEFORE OPERATION
To turn the unit on
1 Turn the VOLUME control toward MIN.
Otherwise, the speakers may be damaged.
2 Press one of the FUNCTION buttons (TUNER, PHONO, AUX/TV, CD, VIDEO 1, VIDEO 2/5 CH or
VIDEO 3) or the TAPE MONITOR button.
Download from Www.Somanuals.com. All Manuals Search And Download.
When pressing the TUNER button, previously tuned station is received (Direct Play Function).
The POWER button is also available.
Operation is possible after four seconds.
To select the front speaker system
To use speaker system A: Set the FRONT SPEAKERS A button to
To use speaker system B: Set the FRONT SPEAKERS B button to
ON.
ON.
To use both speaker systems: Set both the buttons to
ON.
Set the button(s) to OFF to turn off the speaker system(s).
NOTE
As the front speaker systems A and B are connected in series:
- The sound will be slightly decreased when using both speaker systems.
- No sound can be heard if the FRONT SPEAKERS A and B buttons are set to
system is connected.
ON when only one speaker
To change a displayed name for the AUX/TV button and VIDEO 2/5 CH button
When the AUX/TV button is pressed, AUX is displayed initially. It can be changed to TV. With the power on,
press the POWER button while pressing the AUX/TV button.
The displayed name for VIDEO 2/5 CH button can be changed to VIDEO 2, LD or MD; with the power on, press
the POWER button while pressing the VIDEO 2/5 CH button.
This function button also works as the 5 CH surround on/off switch. With this function being selected, press the
VIDEO 2/5 CH button. "5 CH" is displayed and 5 CH surround is turned on.
Using the headphones
Connect the headphones to the PHONES jack with a standard stereo plug (o6.3mm, 1/4 inch). Be sure to set the
FRONT SPEAKERS A and B buttons to OFF. Otherwise sound is output from the speakers.
NOTE
When using the headphones, set the 5 CH surround, DOLBY PRO LOGIC and DSP system to off.
To turn the unit off, press the POWER button.
SETTING THE CLOCK
When the AC cord is connected for the first time, the clock on the display flashes.
Download from Www.Somanuals.com. All Manuals Search And Download.
Set the time as follows while the power is off.
1 Press the SET button.
The hour flashes.
2 Press the DOWN
or UP
button to designate the hour.
3 Press the SET button to set the hour.
The hour stops flashing and the minute starts flashing.
4 Press the DOWN
or UP
button to designate the minute.
5 Press the SET button to set the minute.
The minute stops flashing on the display and the clock starts from 00 second.
To correct the current time
Press the POWER button to turn the unit off. Press the SET button and carry out steps 1 to 5 above.
To display the current time
Press the CLOCK button on the remote control. The clock is displayed for 4 seconds.
To switch to the 24-hour standard
Press the POWER button while pressing the UP
or DOWN
button while the current time is displayed.
Repeat the same procedure to restore the 12-hour standard.
If the clock display flashes while the power is off.
This is caused by a power interruption. The current time needs to be reset.
If power is interrupted for more than approximately 24 hours, all settings stored in memory after purchase need to be
reset.
SOUND pg. 7
CUSTOM AUDIO ADJUSTMENT
VOLUME CONTROL
Turn the VOLUME control on the unit, or press the VOLUME buttons on the remote control.
To adjust the left/right balance
Download from Www.Somanuals.com. All Manuals Search And Download.
Turn the BALANCE control.
To mute the sound temporarily
Press the MUTING button.
"MUTE ON" appears on the display for four seconds. While muting the sound, the selected FUNCTION button
flashes. Press the MUTING button again to restore the sound.
BBE SYSTEM
The BBE system enhances the clarity of high-frequency sound.
Press the BBE button.
Each time it is pressed, the level changes. Select one of the three levels, or the off position to suit your preference.
NOTE
The BBE system is automatically canceled when the 5 CH surround or DOLBY PRO LOGIC is turned on.
SUPER T-BASS SYSTEM
The T-BASS system enhances the realism of low frequency sound.
Press the T-BASS button.
Each time it is pressed, the level changes. Select one of the three levels, or the off position to suit your preference.
NOTE
Low frequency sound may be distorted when the T-BASS system is used for a disc or tape in which low frequency
sound is originally emphasized. In this case, cancel the T-BASS system.
SOUND ADJUSTMENT DURING RECORDING
The output volume and tone (except BBE) of the speakers or headphones may be freely varied without affecting the
level of the recording.
Recording with the BBE
The desired source can be recorded with the BBE function to enhance the clarity of high-frequency sound. When
playing back a tape recorded with BBE, it is recommended that BBE be set to off.
SOUND (cont.) pg. 8
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRONIC GRAPHIC EQUALIZER
This unit provides the following five different equalization modes.
ROCK: Powerful sound emphasizing treble and bass
POP: More presence in the vocals and midrange
JAZZ: Accented lower frequencies for jazz-type music
CLASSIC: Enriched sound with heavy bass and fine treble
BGM: Calm tone with suppressed bass and treble
Press one of the GEQ (Graphic Equalizer) buttons
The selected mode name appears on the display for two seconds, and the selected mode on the right side of the
display is enclosed with parentheses.
To cancel the selected mode
Press the selected button again. "GEQ oFF" appears on the display.
To select with the remote control
Press the GEQ button repeatedly until the desired equalization mode is displayed.
DSP SURROUND
Download from Www.Somanuals.com. All Manuals Search And Download.
The DSP (Digital Signal Processor) surround circuits can recreate the effect of sounds reflected from walls or
ceilings, to obtain the sound presence of real environments. There are four modes with matching graphic
equalization modes. Equalization modes are selected automatically and can also be selected or turned off to suit
your preference.
Press one of the DSP buttons (DANCE, LIVE, HALL, or ARENA).
The selected mode name appears on the display for two seconds, and the selected DSP and matching GEQ modes on
the display are enclosed with parentheses.
When the music source is monaural
Select LIVE to obtain a simulated stereo effect. When DANCE or HALL is selected, no sound will be heard from
the surround speakers.
To cancel the selected mode
Press the selected button again. "DSP oFF" appears on the display. Even if canceling the selected DSP mode, the
matching or selected GEQ mode still remains. While the DSP surround system is off, no sound is heard from the
surround speakers.
To select with the remote control
Press the DSP button repeatedly until the desired DSP mode is displayed.
To adjust the volume of the surround speakers
Press the MANUAL SELECT button once. "SUR" is displayed for four seconds. Press the Up
button while "SUR" is displayed.
or DOWN
Note that the Dolby Pro Logic surround speakers level is also changed (see page 13).
NOTE
The DSP system is automatically canceled when the 5 CH surround or DOLBY PRO LOGIC is turned on.
BASIC OPERATIONS pg. 9
Download from Www.Somanuals.com. All Manuals Search And Download.
SELECTION OF AUDIO/VIDEO SOURCE
1 Select the program source.
Press one of the FUNCTION buttons or the TAPE MONITOR button.
To listen to or watch
The button pressed
TAPE MONITOR
Tape
Radio
TUNER
PHONO
AUX/TVa
CD
Record
Television, etc.
Compact Disc
Video (VCR or LD)
MD
VIDEO 1, VIDEO 2/5 CHa, VIDEO 3
VIDEO 2/5 CHa
DVD
VIDEO 2/5 CH
a) For selecting AUX/TV, or VIDEO 2/LD/MD, see "To change a displayed name for the AUX/TV button and
VIDEO 2/5 CH button" of "BEFORE OPERATION" (see page 6).
NOTE
When using a turntable with a built-in equalizer amplifier, set the switch of the equalizer amplifier to off. See the
instructions of the turntable for further information.
2 Start the selected program source.
3 Adjust the sound.
About the video source to the monitor or TV
V1: VIDEO 1, V2: VIDEO 2, V3: VIDEO 3
The selected video source is indicated on the display and the video signal through the MONITOR VIDEO OUT jack
is output on the TV.
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING AN AUDIO SOURCE
1 Select the program source to be recorded.
Press one of the FUNCTION buttons.
2 Set the tape deck or MD recorder to the recording mode.
3 Start the selected program source.
To monitor recorded sound during recording (when the connected tape deck is a three-head system)
Press the TAPE MONITOR button. "TAPE ON" appears on the display for four seconds, and then the source name
selected in step 1 comes back on. To cancel the tape monitor, press it again so that "TAPE oFF" appears.
NOTE
Any sound control except the BBE system has no effect on recording (see page 7).
TO PLAY A DVD RECORDED IN DOLBY DIGITAL SURROUND
This receiver has 5 ch connectors supporting Dolby Digital decoder with the 5.1 ch output terminals. When a DVD
player, such as Aiwa XD-DV500, that contains a Dolby Digital decoder is connected to the receiver, you can enjoy
theater-quality audio right in your home when playing discs recorded in Dolby Digital Surround.
Preparation
In the initial settings of the DVD player, set the SUBWOOFER mode of SETUP SPEAKERS to OFF. For details,
see the initial settings in the instruction manual of the DVD player.
1 Press the VIDEO 2/5 CH button to select the VIDEO 2 function.
2 Press the VIDEO 2/5 CH button again.
"5 CH" appears on the display and the 5 CH surround is turned on.
3 Start playing the DVD recorded in Dolby Digital Surround.
To turn off the 5 CH surround, press the VIDEO 2/5 CH button once more.
NOTE
• The DOLBY PRO LOGIC, BBE, or DSP system is automatically canceled when the 5 CH surround is turned on.
• See page 13 when adjusting the sound level of the center and surround speakers.
RADIO RECEPTION
pg. 10
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUAL TUNING
1 Press the TUNER button repeatedly to select the desired band.
When the TUNER button is pressed while the power is off, the power is turned on directly.
2 Press the UP
Each time the button is pressed, the frequency changes. When a station is received, "TUNE" is displayed for two
seconds. During FM stereo reception, is displayed.
or DOWN
button to select a station.
To search for a station quickly (Auto Search)
Keep the UP or DOWN button pressed until the tuner starts searching for a station. After tuning in to a
station, the search stops.
To stop the Auto Search manually, press the UP
or DOWN
button.
• The Auto Search may not stop at stations with very weak signals.
When an FM stereo broadcasts contains noise
Press the MONO TUNER button on the remote control so that "MONO" appears on the display.
Noise is reduced, although reception is monaural.
To restore stereo reception, press the button so that "MONO" disappears.
To change the AM tuning interval
The default setting of the AM tuning interval is 10 kHz/step. If you use this unit in an area where the frequency
allocation system is 9 kHz/step, change the tuning interval.
Hold down the TUNER button and press the POWER button immediately. Note that the unit is set to the Direct
Tuning mode if the TUNER button is pressed and held down for about two seconds.
To rest the interval, repeat this procedure.
Download from Www.Somanuals.com. All Manuals Search And Download.
DIRECT TUNING
When you know the frequency of the desired station, you can tune in directly to the station.
1 Press the TUNER button to select a band.
2 Press the TUNER button and hold it down until "-" flashes on the display (Direct Tuning Mode).
3 Press the appropriate numbered buttons to tune in to the desired station.
Example:
To tune in to 106.50 MHz, press 1, 0, 6, 5 and 0 buttons
To tune in to 95.2 MHz, press 9, 5, 2 and 0 buttons.
To cancel the Direct tuning mode
Press the UP
or DOWN
button.
When using the remote control
Carry out steps 1 and 2 above, and press the numbered buttons on the remote control to tune in to the desired station.
NOTE
• When entering a frequency out of tuning range, the value flashes for two seconds and then goes off. Check the
frequency and repeat step 3 correctly.
• When entering a frequency not covered by the tuning interval, the value is automatically rounded up or down to the
closest one covered by it.
RADIO RECEPTION (cont.) pg. 11
PRESETTING STATIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
The unit can store a total of 32 preset stations. When a station is stored, a preset number is assigned to the station.
Use the preset number to tune in to a preset station directly.
1 Press TUNER to select a band, and press the UP
is also available.
or DOWN
button to select a station. Direct tuning
2 Press the SET button to store the station.
A station is assigned a preset number, beginning from 1 in consecutive order for each band.
3 Repeat steps 1 and 2.
No more stations will not be stored if a total of 32 preset stations have already been stored for all the bands.
NOTE
When the AM tuning interval is changed, all preset stations are cleared. The preset stations have to be set again.
PRESET NUMBER TUNING
1 Press the TUNER button to select a band.
2 Press the numbered buttons to select a preset number.
Example:
To select preset number 25, press 2 and 5.
To select preset number 7, press 0 and 7.
To clear a preset station
Select the preset number of the station to be cleared. Then, press the SET button, and press the SET button again
within 4 seconds.
The preset numbers of all other stations in the band with higher numbers are also decreased by one.
When using the remote control
Press the TUNER BAND button to select a band, then press the numbered buttons to select a preset number.
DOLBY PRO LOGIC
pg. 12
The Dolby Pro Logic feature and the center and surround speakers (standard) assure full-scale home theater sound.
When playing back laser discs or video software that have been specially recorded with four-channel sound (left,
Download from Www.Somanuals.com. All Manuals Search And Download.
right, center, surround) and steering logic (for directing sound), astonishingly realistic sound surrounds the listener to
create a new level of audio/visual entertainment.
Independent control of the four channels allows the listener to enjoy the same type of sound reproduction
experienced in movie theaters. Voices are reproduced in the front and center sound field, while ambient sounds like
cars and crowds are reproduced on all sides of the listener for an incredibly lifelike audio/video experience. Please
read the following carefully to "tune" the systems output to match the characteristics of your listening space.
Check the following:
• Before using the DOLBY PRO LOGIC, adjust the proper balance of the speaker sound levels (see page 13).
• Make sure the speakers are properly connected and positioned (see pages 3 and 4).
• Make sure the TV set and video unit are properly connected (see page 3).
• Make sure the laser disc and video tape, etc., support
.
SELECTING DOLBY PRO LOGIC
The optimal Dolby Pro Logic mode depends on the type and placement of the speakers. It is recommended that the
optional Aiwa speakers should be used for all channels, for example, the SX-R1000 for surround speakers, the
SX-C1000 for a center speaker and the SX-AV1000 for front speakers. Check your current type and placement of the
speakers and select the recommended Dolby Pro Logic mode accordingly.
The recommended mode
PHANTOM mode: Select this mode when the center speaker is not connected. All center channel signals are
redistributed to the left and right channel speakers.
3CH LOGIC mode: Select this mode when the surround speakers are not connected.
TO SELECT A DOLBY PRO LOGIC MODE
1 Press the DOLBY PRO LOGIC button repeatedly to select the appropriate mode.
When selecting the DOLBY PRO LOGIC or 3CH LOGIC mode, the indicator lights up, and the selected mode name
runs through on the display. Each time the button is pressed, the mode changes as shown below.
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Press the DOLBY PRO LOGIC button again and hold it down until the center speaker mode to be selected
appears.
When selecting the DOLBY PRO LOGIC mode in step 1:
"NORMAL", "WIDE" and "PHANTOM" appear in turn.
When selecting the 3CH LOGIC mode in step 1:
"NORMAL" and "WIDE" appear one after another.
NOTE
• Depending on the sound source or listening condition, surround effect may not be obtained even when the DOLBY
PRO LOGIC is on.
• The full DOLBY PRO LOGIC effect cannot be obtained when using the software without
mark. In this case, use the DSP surround system instead (see page 8).
• The DOLBY PRO LOGIC system is automatically canceled when the BBE or DSP system is turned on.
DOLBY PRO LOGIC (cont.)
pg. 13
ADJUSTING SPEAKER LEVEL BALANCE
The unit is equipped with a built-in test signal generator called a noise sequencer for easy balance adjustment of all
four channels. The sequencer outputs a noise signal that "travels" from channel to channel, enabling the simple
adjustment of sound level to achieve the same apparent loudness, at your listening position, from each channel.
1 Select the Dolby Pro Logic mode according to your current type and placement of the speakers.
(See page 12.)
2 Press the MANUAL SELECT button and hold it down for about two seconds until "L TEST" appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
A noise signal is sent to each channel in turn as follows:
3 Adjust the sound level of the center and (or) surround speakers.
While "CEN" or "SUR" is displayed, press the UP
or DOWN
button to adjust the volume of the center or
surround speakers to match the level of the left and right speakers.
To adjust the balance between the left and right speakers, use the BALANCE control while "L TEST" or "TEST R"
is displayed.
4 Press the MANUAL SELECT button again to stop the noise signal.
NOTE
If the surround speakers volume of the DSP is changed (see page 8), the Dolby Pro Logic surround speakers level is
also changed.
About the channels
The left and right speakers create the stereo effect.
The center speaker helps achieve precise sound positioning over a broad sound field.
The rear-mounted surround speakers enhance the "depth" of the sound field.
To change the delay time
The surround speakers reproduce sounds a split second after the front speakers. The delay is initially set to 20ms
(milliseconds).
To change this standard delay time, press the MANUAL SELECT button twice or three times so that "TIME" is
displayed. Then, press the UP
changes as shown below.
or DOWN
button. Each time one of the buttons is pressed, the delay time
To change the sound levels after adjusting the balance with the noise sequencer
The sound levels of the center and surround speakers can be adjusted during play of a laser disc or video software.
1 Press the MANUAL SELECT button once or twice to select "CEN" or "SUR" (center or surround).
Download from Www.Somanuals.com. All Manuals Search And Download.
2 While the "CEN" or "SUR" is displayed, press the UP
or DOWN
button to adjust the volume
To adjust the sound levels of the center and surround speakers in the 5 CH surround
1 Turn the 5 CH surround on and play the DVD recorded in Dolby Digital Surround.
2 Press the MANUAL SELECT button repeatedly.
Speaker names appear in turn as follows:
Press the Up
or DOWN
button while C, SL, or SR is displayed.
Each level can be adjusted between -10 dB and +10 dB.
TIMER pg. 14
SETTING THE SLEEP TIMER
The unit can be automatically turned off at a specified time.
Use the remote control
1 Press the SLEEP button
2 Press the UP or DOWN
button within four seconds to specify the time until the power is turned off.
Each time the button is pressed, the time changes between 5 and 240 minutes in 5-minute steps.
To check the time remaining until the power turns off
Press the SLEEP button once. The remaining time is displayed for four seconds.
To cancel the sleep timer
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the SLEEP button twice so that "SLEEP" on the display disappears.
GENERAL
CARE AND MAINTENANCE
Occasional care and maintenance of the unit is needed to optimize the performance of your unit.
To clean the cabinet
Use a soft dry cloth.
If the surfaces are extremely dirty, use a soft cloth lightly moistened with mild detergent solution. Do not use strong
solvents, such as alcohol, benzine or thinner as these could damage the finish of the unit.
GENERAL (cont.) pg. 15
SPECIFICATIONS
FM tuner section
Tuning range
Usable sensitivity (IHF)
Antenna terminals
87.5 MHz to 108 MHz
13.2 dBf
75 ohms (unbalanced)
AM tuner section
Tuning range
530 kHz to 1710 kHz (10 kHz step),
531 kHz to 1602 kHz (9 kHz step)
350 µV/m
Usable sensitivity
Antenna
Loop antenna
Amplifier section
Power output
[Stereo Mode]
Front
75 watts per channel, Min. RMS at 4 or 8 ohms, from 40 Hz to
20 kHz, with no more than 0.9% Total Harmonic Distortion
[Dolby Pro Logic or 5 CH Surround Mode]
Front
70 watts per channel, Min. RMS at 4 or 8 ohms, from 40 Hz to
20 kHz, with no more than 0.9% Total Harmonic Distortion
Rear (Surround)
70 watts per channel, Min. RMS at 4 or 8 ohms, 1 kHz, with
no more than 0.9% Total Harmonic Distortion
0.07% (50 W, 1kHz, 8 ohms, Front)
AUDIO IN
Total harmonic distortion
Inputs
PHONO: 2.8 mV (50 kohms)
CD: 370 mV (50 kohms)
TAPE MONITOR: 200 mV (25 kohms)
Download from Www.Somanuals.com. All Manuals Search And Download.
SURROUND IN: 400mV (50 kohms)
VIDEO IN: 1 Vp-p (75 ohms)
Outputs
AUDIO OUT (REC OUT): 230 mV (2 kohms)
VIDEO OUT (MONITOR): 1Vp-p (75 ohms)
SUPER WOOFER: 3.1 V
FRONT SPEAKERS IMP: 8 Ω/4 Ω selectable (front speakers A and B)
With the SPEAKER IMPEDANCE SELECTOR set to 8Ω, accepts speakers of
8 ohms or more
SURROUND SPEAKERS IMP: 8 Ω (surround speakers): accepts
speakers of 8 ohms or more
CENTER SPEAKER IMP: 8 Ω/4Ω selectable
With the SPEAKER IMPEDANCE SELECTOR set to 4 Ω accepts speaker of 4
ohms
With the SPEAKER IMPEDANCE SELECTOR set to 8 Ω accepts speaker of 8
ohms
PHONES (stereo jack): accepts headphones of 32 ohms or more
Muting
-20 dB
General
Power requirements
Power consumption
Dimensions (W × H × D)
Weight
120 V AC, 60 Hz
180 W
360 × 153.5 × 341 mm (14 1/4 × 6 1/8 × 13 1/2 in.)
8.9 kg (19 lb 10 oz.)
Specifications and external appearance are subject to change without notice.
The word "BBE" and the "BBE symbol" are trademarks of BBE Sound, Inc.
Under license from BBE sound, Inc.
DOLBY PRO LOGIC
Manufactured under license from Dolby Laboratories Licensing Corporation.
"DOLBY" the double-D symbol
Corporation.
and "PRO LOGIC" are trademarks of Dolby Laboratories Licensing
GENERAL (cont.) pg. 16
TROUBLESHOOTING GUIDE
If the unit fails to perform as described in these Operating Instructions, check the following guide.
GENERAL
There is no sound.
• Is the AC cord connected properly?
• Is there an incorrect connection? (→ page 3)
• There may be a short circuit in the speaker terminals.
→ Disconnect the AC cord, then correct the speaker connections.
• Was an incorrect function button pressed?
Download from Www.Somanuals.com. All Manuals Search And Download.
• Are the FRONT SPEAKERS A and B buttons set correctly? (→ page 6)
Sound is emitted from one speaker only.
• Is the BALANCE control set appropriately?
• Is the other speaker disconnected?
Sound is heard at a very low volume.
• Has the MUTING button been pressed?
An erroneous display or a malfunction occurs.
→ Reset the unit as stated below.
TUNER SECTION
There is constant wave-like static.
• Is the antenna connected properly? (→ page 5)
• Is the signal weak?
→ Connect an outdoor antenna.
The reception contains noise interference or the sound is distorted.
• Is the system picking up external noise or multipath distortion?
→ Change the orientation of the antenna.
→ Move the unit away from other electrical appliances.
To reset
If an unusual condition in the display window or malfunction occurs, reset the unit as
follows.
1 Press the POWER button to turn off the power.
2 Press the POWER button while pressing the SET button.
Everything stored in memory after purchase is canceled.
If the power cannot be turned off in step 1 because of a malfunction, reset by
disconnecting the AC cord and repeat step 2.
PARTS INDEX
Instructions about each part on the unit or remote control are indicated on the pages listed below.
(in alphabetical order)
Parts
Pages
6, 9
7, 13
7
AUX/TV
BALANCE
BBE
CD
CLOCK
6, 9
6
DOLBY PRO LOGIC
12, 13
DOWN
DSP
(
)
6, 8, 10, 11, 13, 14
8
FRONT SPEAKERS A, B
GEQ
6
8
MANUAL SELECT (TEST)
MONO TUNER
MUTING, MUTE
PHONES
8, 13
10
7
6
PHONO
6, 9
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER
SET
SLEEP
6, 10
6, 11
14
SPEAKER IMPEDANCE
SELECTOR
4
TAPE MONITOR
T-BASS
6, 9
7
TUNER, BAND DIRECT
6, 9, 10, 11
UP
(
)
6, 8, 10, 11, 13, 14
VIDEO 1
6, 9
VIDEO 2/5 CH, LD/MD
VIDEO 3
VOLUME
6, 9
6, 9
7
Back Cover
AIWA CO., LTD
For Assistance And Information Call Toll Free 1-800-BUY-AIWA (United States and Puerto Rico)
Printed in Malaysia
Download from Www.Somanuals.com. All Manuals Search And Download.
|