Dual Fuel Range
Users Guide
&
Installation Instructions
This book contains many important safety messages.
Always read and obey all safety messages.
Installer:Leave these instructions with the appliance
U104001-03
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
If the information in this manual is not followed exactly, a fire or explosion
may result causing property damage, personal injury or death.
Do not store or use gasoline or other flammable vapors and liquids in
the vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance.
Do not touch any electrical switch
Do not use any phone in your building.
Immediately call your gas supplier from a neighbor’s phone. Follow
the gas supplier’s instructions.
If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified
installer, service agency or the gas supplier.
Warning
The anti-tip device supplied with this range must be correctly fitted when
the appliance is installed. This will reduce risk of tipping of the appliance
from abnormal usage or by excessive loading of the oven door
WARNING
• ALL RANGES CAN
TIP
• INJURY TO PERSONS
COULD RESULT
• INSTALL ANTI-TIP
BRACKET PACKED
WITH RANGE
• SEE INSTALLATION
INSTRUCTIONS
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Range
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Range
Contents
General Safety Instructions
Page 8
Page 10
Page 11
Page 12
Page 12
Page 12
Page 13
Page 15
Page 16
Page 17
Page 18
Page 18
Page 19
Cooktop Burners
The Broiler
The Ovens
The Left Hand Multi-function Oven
The Right Hand Convection Oven
The Clock
Both ovens
Multi-function oven
Handyrack
Oven racks
Oven light
Storage
Multi-function (Left hand) Oven cooking guide Page 20
Cooking chart
Page 21
Page 22
Page 24
Page 26
Page 29
Cleaning your range
Troubleshooting
Service and spares
Installation
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions before using this appliance.
Important Safety Information
Save these instructions for future reference.
Have your appliance properly installed
and grounded by a qualified technician in
accordance with the National Electrical
Code ANSI/NFPA No. 70—latest edition, and
local code requirements. In Canada, electrical
grounding must be in accordance with the current
CSA C22.1 Canadian Electrical Code Part 1 and/
or local codes.
In Case of Fire
Do not use water on grease fires. Never
pick up a flaming pan. Turn the controls off.
Smother a flaming pan on a cooktop burner
by covering the pan completely with a well
fitting lid or baking tray. If available use a
multipurpose dry chemical or foam-type fire
extinguisher.
Install only as described in the installation
section of this book.
If fire is in the oven or broiler pan, smother by
closing oven door. Open doors and windows
or if a hood is fitted turn it on to remove
smoke and odor.
Ask your dealer to recommend a qualified
technician and an authorized repair service.
Know how to disconnect the power to the
range at the circuit breaker or fuse box in
case of an emergency.
To Prevent Fire or Smoke Damage
Before using the range make sure all the
packing materials have been removed.
Always keep the area around the range free
from combustible materials, gasoline, and
other flammable vapors and liquids.
The anti-tip device supplied with this range
must be correctly fitted when the appliance
is installed. This will reduce risk of tipping
of the appliance from abnormal usage or by
excessive loading of the oven door
If the range is installed near a window, proper
precautions should be taken to prevent
curtains from blowing over the burners.
NEVER leave any items on the range
cooktop.The hot air from the oven or
broiler vent may ignite flammable items
and may increase pressure in closed
containers, which may cause them to
burst. Many aerosol-type spray cans are
EXPLOSIVE when exposed to heat and
may be highly flammable. Avoid their use
or storage near an appliance.
WARNING
• ALL RANGES CAN TIP
• INJURY TO PERSONS
COULD RESULT
• INSTALL ANTI-TIP
BRACKET PACKED
WITH RANGE
Many plastics will burn and most are
damaged by heat. Keep plastic items away
from parts of the range that may become
warm or hot. Do not leave plastic items on the
cooktop as they may burn, melt or soften if
left too close to a vent or a lighted burner.
• SEE INSTALLATION
INSTRUCTIONS
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions before using this appliance.
Important Safety Information
Save these instructions for future reference.
Storage should not be fitted directly above a
range. If anything is stored above the range,
it should be limited to infrequently used
items which can be safely stored in an area
subjected to heat from a range. Temperatures
may be unsafe for some items, such as
volatile liquids, cleaners or aerosol sprays.
Do Not Leave Children Alone
Babies, toddlers and young children should
not be allowed near the range at any time.
They should never be allowed to sit or stand
on any part of the appliance.
Destroy the carton and plastic bags after
unpacking the range. Never allow children to
play with packaging material.
Do not allow children to climb or play around
the range. The weight of a child on an open
door may cause the range to tip, resulting in
serious burns or other injury.
Teach them not to play with controls or any
other part of the range.
For safety considerations never use your
range to heat the room.
Never store items of interest to children in
the cabinets above a range or on backguard
of a range; children climbing on the range to
reach them could be seriously injured.
User servicing—Do not repair or replace
any part of the appliance unless specifically
recommended in this User Manual.
All other servicing should be done only by a
qualified technician, this may reduce the risk
of personal injury and damage to the range.
Do not use the oven for storage.
This instruction is based on safety
considerations
Never modify or alter the construction of a
range by removing leveling legs, panels, wire
covers, anti-tip brackets/screws, or any other
part of the product.
Flammable materials should not be stored
in an oven, the grill chamber, the range
storage drawer or near the cooktop burners.
This includes paper, plastic and cloth items,
such as cookbooks, plasticware and towels,
as well as flammable liquids. Do not store
explosives, such as aerosol cans, on or near
the appliance.
To avoid personal injury, do not sit, stand or
lean on oven or grill doors or drawer.
Flammable materials may explode and result
in fire or property damage..
Leaning, sitting or stepping on the doors or
drawer of this range can result in serious
injuries and also cause damage to the range.
Do not allow anyone to climb, stand or hang
on any part of the range.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions before using this appliance.
Important Safety Information
Save these instructions for future reference.
cooktop. Flammable material could be ignited
if brought in contact with a burner flame or
hot surface and may cause severe burns.
To avoid risk of electrical shock, personal
injury, or death, make sure your range
has been properly grounded and always
disconnect it from main power supply before
servicing.
Use Only Dry Potholders or Oven Gloves
Moist or damp potholders on hot surfaces
may result in burns from steam. Never let a
potholder touch hot heating elements.
Do not use a towel or other bulky cloth in
place of a glove. They might catch fire if they
touch a hot surface.
Use dry oven gloves when applicable - using
damp gloves might result in steam burns
when you touch a hot surface. Never operate
the range with wet hands.
Do not touch cook top burners or areas near
burners
Gas burners may be hot even if they have
been off for some time. Areas near the gas
burners may become hot enough to cause
burns. During and after use, do not touch,
or let clothing touch or other flammable
materials contact the burners or areas near
the burners until they have had enough time
to cool. These areas include the rangetop
and backguard.
Important Safety Notice and Warning
The California Safe Drinking Water and Toxic
Enforcement Act of 1986 (Proposition 65)
requires the Governor of California to publish
a list of substances known to the State of
California to cause cancer or reproductive harm,
and requires businesses to warn customers of
potential exposures to such substances.
DO NOT TOUCH HEATING ELEMENTS OR
INTERIOR SURFACES OF OVENS
This appliance contains or produces a chemical
or chemicals which can cause death or serious
illness and which are known to the state of
California to cause cancer, birth defects or other
reproductive harm.
Oven and Broiler heating elements may be
hot though they are dark in color. Interior
surfaces of an oven or broiler may become
hot enough to cause burns. During and after
use, do not touch, or let clothing or other
flammable materials touch heating elements
or interior surfaces of oven until they have
had enough time to cool.
Users of this appliance are hereby warned
that the burning of gas can result in low-level
exposure to some of the listed substances,
including benzene, formaldehyde and soot, due
primarily to the incomplete combustion of natural
gas or liquid petroleum (LP) fuels. Properly
adjusted burners will minimize incomplete
combustion. Exposure to these substances
can also be minimized by properly venting the
burners to the outdoors.
Other range surfaces that may become hot
enough to cause burns are the oven door
and oven vent at the base of the range
splashback.
To reduce the risk from substances in the fuel or
from fuel combustion make sure this appliance
is installed, operated, and maintained according
to the instructions in this booklet.
Wear Suitable Clothing
Never wear loose-fitting or hanging clothes
while using the range. Be careful when
reaching for items stored in cabinets over the
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions before using this appliance.
Important Safety Information
Save these instructions for future reference.
Use the Right Size Pan
Important: Never keep pet birds in the kitchen
or in rooms where the fumes from the
kitchen could reach. Birds have a very
sensitive respiratory system. Fumes
released due to overheated cooking oil,
fat, margarine and overheated non-stick
cookware may be harmful.
This appliance is equipped with burners of
different sizes. Use utensils with flat bottoms.
Do not use unstable pans and position the
handles away from the edge of the cooktop.
Make sure the flames are under the pans. It’s
not safe to let the flames burn up the sides of
the pan; the handle may get too hot.
Important - Save the installation instructions
for the local electrical inspector’s use.
Proper relationship of utensil to burner will
also improve efficiency.
Proper Installation
Never Leave Cooktop burners unattended
at high settings. Pans boiling over can
cause smoking and greasy spills may
catch on fire.
Be sure your appliance is properly installed
and grounded by a qualified technician.
Protective Liners - Do not use aluminum foil
to line cooktop bowls or oven bottoms.
Foil liners may result in a risk of electric
shock, or fire and will damage the enamel
finish. Never allow aluminum foil to
contact the heating elements.
User Servicing
Do not repair or replace any part of the
appliance unless specifically recommended
in the manual. All other servicing should be
referred to a qualified technician.
Glazed Cooking Utensils - Only certain
types of glass, glass/ceramic, ceramic,
earthenware, or other glazed utensils
are suitable for range-top use without
breaking due to the sudden change in
temperature.
Cooktop burners
Quality of Flames
On Natural Gas the burners’ flames should be
a blueish color with, at most, a slight yellowish
fringe.
Utensil handles should be turned inward and
not over adjacent burners. If handles are
left over adjacent burners they will get
hot and may burn.
On Propane gas the flames may be “softer”.
The cooktop burner flames may have a slight
yellowish tip.
If the flame burns with a long white tip you
should call for service.
Normal flame appearance
Burner not fitted correctly
MAKE SURE THE FLOW OF COMBUSTION
AND VENTILATION AIR TO THE RANGE IS
UNOBSTRUCTED.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions before using this appliance.
Important Safety Information
Save these instructions for future reference.
Ovens
Use Care When Opening Door
General Safety Instructions
This appliance must be installed by a
competent person in accordance with the
installation instructions. The installation must
comply with the relevant regulations and
also the local electricity supply company
requirements
Let hot air and steam escape before
removing or replacing food.
Never heat unopened food containers.
Pressure build up may make container
burst and cause injury.
This appliance is designed for domestic
cooking only. Use for any other purpose could
invalidate any warranty or liability claim.
Keep oven vent ducts unobstructed.
Placement of Oven Racks
Always place oven racks in desired location
while oven is cool. If rack must be moved
while oven is hot, do not let potholder contact
hot heating element in oven.
The use of a gas cooking appliance results
in the production of heat and moisture in
the room in which it is installed. Ensure that
the kitchen is well ventilated: keep natural
ventilation holes open or install a mechanical
ventilation device, (mechanical extractor
hood).
CAUTION
Do not store items of interest to children in
cabinets above a range or on the backguard
of a range - children climbing on the range to
reach items could be seriously injured.
Prolonged intensive use of the appliance
may call for additional ventilation, for
example opening a window, or more effective
ventilation, for example increasing the level of
mechanical ventilation where present.
WARNING
THIS APPLIANCE IS PROVIDED WITH
ROLLERS TO FACILITATE MOVEMENT
DURING INSTALLATION. THE RANGE
SHOULD NOT BE MOVED AFTER
INSTALLATION.
The range should be serviced by a qualified
service engineer and only approved spare
parts used. Have the installer show you the
location of the range control switch. Mark it
for easy reference. Always allow the range to
cool and then switch off at the mains before
cleaning or carrying out any maintenance
work, unless specified otherwise in this guide.
All parts of the range become hot with use
and will retain heat even after you have
stopped cooking.
Take care when touching range, to minimize
the possibility of burns, always be certain that
the controls are in the OFF position and that
it is cool before attempting to clean the range.
Clean with caution. If a wet sponge or cloth
is used to wipe spills on a hot surface, be
careful to avoid steam burns. Some cleansers
can produce noxious fumes if applied to a hot
surface.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions before using this appliance.
Important Safety Information
Save these instructions for future reference.
Clean only parts listed in this guide.
When using an electrical appliance near
the cooktop, be sure that the cord of the
appliance does not come into contact with
the cooktop.
In the interests of hygiene and safety the
range should be kept clean at all times as
a build up in fats and other food stuff could
result in a fire.
Take care that no water seeps into the
appliance
Always keep combustible wall coverings or
curtains etc. a safe distance away from your
range.
Make sure that your kitchen is well ventilated
at all times. Use extractor fans or hoods when
fitted.
Do not spray aerosols in the vicinity of the
range while it is in use.
The range is designed for cooking foods only
and must not be used for any other purpose.
Do not store or use combustible materials,
or flammable liquids in the vicinity of this
appliance.
The oven should NOT be used for heating the
kitchen, not only does this waste fuel but the
control knobs may become overheated.
Take great care when heating fats and oils,
as they will ignite if they get too hot.
When the oven is on DO NOT leave the oven
door open for longer than necessary.
Use a deep fat thermometer whenever
possible to prevent overheating fat beyond
the smoking point.
The specification of this range should not be
altered.
Never leave a deep fry pan unattended.
Always heat fat slowly, and watch as it heats.
Deep fry pans should be only one third full
of fat. Filling the pan too full of fat can cause
spill over when food is added. If you use a
combination of oils or fats in frying, stir them
together before heating, or as the fats melt.
This appliance is heavy, take care when
moving it.
When the range is not in use ensure that the
control knobs are in the off position.
Foods for frying should be as dry as possible.
Frost on frozen foods or moisture on fresh
foods can cause hot fat to bubble up and over
the sides of the pan. Carefully watch for spills
or overheating of foods when frying at high or
medium high temperatures. Never try to move
a pan of hot fat, especially a deep fry pan.
Wait until the fat is cool.
When the broiler is on, do not use the top of
the flue (the slot along the back of the range)
for warming plates, dishes, drying dish towels
or softening butter.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Range
Cooktop Burners
The drawing by each knob indicates which burner that
knob controls. Each burner has a special safety device
that stops the flow of gas if the flame goes out.
Push in and turn a knob to the ( ) lighting position.
Simmering aids, such as asbestos or mesh mats,
are NOT recommended. They will reduce burner
performance and could damage the grates.
Keep holding the knob pressed in to let the gas through
to the burner for few seconds. The igniter should spark
and light the gas.
Avoid using unstable and misshapen pans that may
tilt easily and pans with a very small base diameter
e.g. milk pans, single egg poachers. The minimum pan
diameter recommended is 43/4”.
If, when you let go of the control knob, the burner goes
out, the safety device has not held in. Turn the control
to the off position and wait one minute, then try again
this time holding in the control knob for slightly longer.
The Wok burners are designed to provide even heat
over a large area. They are ideal for large pans and
stir frying. When using large pans ensure that the
pan does not over hang the edge of the cooktop. For
heating smaller pans the smaller burners may be more
efficient.
When a cooktop burner knob is pressed in,
sparks will be made at every burner, this is
normal.
Adjust the flame height to suit by turning the knob. On
this range the low position is beyond high, not between
high and off. The ‘LO’ marks the low position. Turn the
knob towards it after the contents of a pan have boiled.
If after lighting, a cooktop burner’s flame goes
out, turn it off and leave it for one minute before
relighting it.
Igniting Cooktop Burners without Electricity
If there is a power failure, the cooktop burners
can be lit with a match.
1. Hold a burning a match ½ inch from the
burner head keeping your hand as far
Make sure flames are under the pans. For safety
reasons, adjust the flames so that they do not extend
beyond the edge of the cooking utensil. This instruction
is based on safety considerations.
Pans and kettles with concave bases or down turned
base rims should not be used.
horizontally away from the burner as possible.
2. Push and turn burner control knob to HI/
lighting position. As soon as the burner flame
lights move your hand away. With your other
hand, keep holding the knob pressed for a few
seconds so that the burner safety device can
‘sense’ the heat of the flame.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Range
3. Turn burner control knob to OFF position
when finished.
You can remove the burner cap and head for
cleaning, see page 23.
You should wipe the enamel top surface of the
range around the cooktop burners as soon as
possible after spills occur.
Note:
For best results preheat for 2 minutes with the broiler
pan in position. After placing your food on the broiler
pan grid, slide the broiler pan onto the side supports.
Adjust the heat to suit by turning the knob.
Make sure it is pushed right in and touches the
back stop.
Use of aluminum pans may cause metallic
marking of the grates. This does not affect the
durability of the enamel and may be cleaned off
with a metal polish.
Never close the broiler door when the broiler is on.
The Broiler
CAUTION: Accessible parts may be hot when
the broiler is in use.Young children should
be kept away.
The broiler pan grid can be turned over to give two
cooking positions.
Remove the pan from the bottom of the broiler
compartment.
Don’t leave the broiler on for more than a few
moments, without the broiler pan underneath it.
For best results, especially with toast,
preheat the broiler with the broiler pan in the
cooking position for two minutes before use.
The broiler grid can be removed and the food
placed on it while you are waiting for the broiler
to preheat.
After placing your food on the broiler pan grid, slide
the broiler pan onto the side supports just below the
elements. Make sure it is pushed right in and touches
the backstop.
The broiler pan grid can be turned over to
give two cooking positions.
You can brown the top of dishes cooked in the
oven, under the broiler by placing the dish onto
the base of the broiler pan, which can easily
slide along the floor of the broiler cavity.
The broiler has two elements that allow either the
whole area of the pan to be heated or just the right
hand half.
Turn the knob to position 3.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Range
The Ovens
During use the appliance becomes hot. Care should be taken to avoid touching the heating
elements inside the oven.
The clock must be set to the time of day before the ovens will work. See ‘The Clock’ section for
instructions on setting the time of day.
The Left Hand Multi-function Oven The Right Hand Convection Oven
The left hand oven is a Multi-function oven. As well
as the oven fan and fan element, it is fitted with
two extra heating elements, one visible in the top
of the oven and the second under the oven base.
Take care to avoid touching the top element and
element deflector when placing or removing items
from the oven. For more detail on this oven see
the section ‘Multi-function oven’.
The fan in the right hand Tall oven circulates hot
air continuously, which means faster more even
cooking.
The recommended cooking temperatures for a
fanned oven are generally lower than a non-fanned
oven.
function
temperature
The right hand fan oven control is at the right hand
end of the control panel.
The Multi-function oven has two controls, a
function selector and a temperature setting knob.
Turn the function selector control to a cooking
function. This is the fan oven setting.
Turn the oven temperature knob to the
temperature you need.
Turn the oven temperature knob to the
temperature you need.
The oven heating light will glow until the oven has
reached the temperature you selected. It will then
cycle on and off during cooking.
The oven heating light will glow until the oven has
reached the temperature you selected. It will then
cycle on and off during cooking.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Range
To stop the beeper when it sounds
The Clock
Turn the Adjusting knob counter clockwise
Setting the time of day
To stop automatically
Use when you have started the oven manually.
Turn the Setting knob to
the ( ) position.
Use the adjustment
knob to set the time you
need.
‘Stop Time’ shows.
AUTO will show in the
display.
Setting knob
Adjusting knob
When the clock is first connected the display will
flash ( ) and ( ) alternately.
To set the clock to read
the time of day turn and
hold the Setting knob to
Turn the Setting knob to the (AUTO) setting.
When your cooking is finished the beeper
sounds. Turn the Setting knob to the vertical ( )
to return to manual cooking.
the clock symbol (
)
and at the same time
turn the Adjusting knob
left or right until the
clock shows the time of
day. .
To start and stop the oven
automatically (delayed baking)
Let go of the Setting knob and it will spring back
to the vertical ( ) oven manual setting.
Before you set the clock, you must have two
numbers clearly in mind.
If the key symbol ( ) appears on the left of the
display you have accidentally turned on the
key lock feature. See the section ‘Clock Special
Features’.
The ‘cook time’, which is the period of time you
want the oven to cook. The maximum cooking
time is 11 hours 59 minutes.
The ‘stop time’, which is the time of day you
want the oven to stop cooking. This must be less
than 12 hours from the current time.
To time something that’s cooking
(minute minder)
You cannot set a start time directly - this is set
automatically by setting the cooking period and
stop time.
Turn the Setting knob
to the right to the ( )
minute minder setting
- it should click into
position.
Use the adjustment
knob to set the time
you need.
Turn the Setting knob to
the ( ) position.
Use the Adjusting knob
to set the ‘cooking time’
you need.
You can turn the knob
back to the ( ) manual
setting to keep an eye
on the time of day
or leave it in the ( )
minute minder position
as the time ticks down.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Range
Clock Special Features
Turn the Setting knob to
the ( ) position.
Key Lock
The display will show
the current time of day
plus the ‘cook period’
you just set.
When the key lock is activated, the clock can
be operated as usual but the ovens are locked
and will not come on. This means that your child
could select a cook program but the program will
not be activated and ovens will not switch on.
Use the adjustment knob to set the ‘Stop time’
you need.
To activate the key lock
Turn and hold the
Setting knob to the clock
symbol ( ) for about 8
seconds.
‘Stop Time’ shows.
AUTO will show in the
display.
‘On’ will appear on the
display.
Keep holding the
Set the oven(s) to the cooking temperature you
need (don’t forget to set a function if using the
Multi-function oven).
Setting knob turned to
the clock symbol (
)
and turn the Adjusting
knob clockwise until the
key symbol ( ) and ‘Of’
shows on the display.
Let go of the knobs.
Turn the Setting knob to
the (AUTO) setting.
The clock shows the
time of day and ‘AUTO’.
The ovens are now
locked. After a few
seconds the display
will revert to show the
time of day and the key
symbol.
When your cooking is finished the beeper
sounds. Turn the Setting knob to the vertical ( )
to return to manual cooking.
To turn off the key lock
If you are out, don’t worry about the beeper
going off, it stops after a while. When you return,
turn the Setting knob to the vertical ( ) to return
to manual cooking. Turn the thermostat to the off
position.
Turn and hold the
Setting knob to the clock
symbol ( ) for about 8
seconds. ‘Of’ will appear
on the display.
AUTO is showing, you want to
reset to manual cooking.
Keep holding the Setting
knob turned to the
You can cancel any automatic settings by briefly
turning the Setting knob to the manual symbol
( ).
clock symbol ( ) and
turn the Adjusting knob
clockwise until the key
symbol ( ) goes out on
the display. Let go of the
knobs.
After a few seconds
the display will revert to
show the time of day.
The ovens can now be used normally.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Range
Cooking using the timer (Delayed
baking)
Both ovens
Before using for the first time, heat the ovens
to 400°F for 30 minutes to expel manufacturing
odors.
The timer can be used to turn just one oven
or both on and off automatically. The start and
stop time must be the same for both ovens but
different cooking temperatures can be set.
The wire racks should always be pushed firmly
to the back of the oven.
If you want to turn one of the ovens on
at the same time as the timer is set for
automatic cooking, you must wait until
the timer has turned on the oven/ ovens
first. Then you can adjust either of them
manually in the normal way.
Bakeware, meat pans etcetera should be placed
level centrally on the oven’s wire racks. Keep all
trays and containers away from the sides of the
oven, as overbrowning of the food may occur.
For even browning, the maximum recommended
size of a baking sheet is 11 3/8” x 13’’.
You can set the oven for a combined delay and
cook cycle of up to 11 hours 59 minutes.
Cooking high moisture
content foods can create
a ‘steam burst’, when the
oven door is opened. When
opening the oven stand well
back and allow any steam to
disperse.
If you want to cook more than one dish,
choose dishes that require approximately
the same time. However, dishes can be
‘slowed down’ slightly by using small
containers and covering them with
aluminum foil, or ‘speeded up’ slightly by
cooking smaller quantities or placing in
larger containers. Never allow aluminum foil to
contact the heating elements.
When the oven is on, don’t
leave the door open for longer
than necessary, otherwise the
knobs may get very hot.
Very perishable foods such as pork, dairy
products or seafood should be avoided if a
long delay period is planned, especially in hot
weather.
• Always leave a ‘fingers width’ between dishes
on the same rack. This allows the heat to
circulate freely around them.
Don’t place warm food in the oven.
Don’t use an oven already warm.
Don’t use if an adjoining oven is warm.
• Cover meat when cooking to avoid fat
splashes.
Avoid using wine or beer if there is a delay
period, as fermentation may take place.
• To reduce fat splashing when you add
vegetables to hot fat around a roast, dry them
thoroughly or brush lightly with cooking oil.
• Sufficient heat rises out of the oven while
cooking to warm plates in the broiler
compartment.
• If you want to brown the base of a pastry
dish, preheat the baking sheet for 15 minutes
before placing the dish in the center of the
sheet or use the base heat in the Multifunction
oven.
To avoid curdling, cream should be added to
dishes just before serving.
Fresh vegetables, which may discolor during a
delay period, should be coated in melted fat or
immersed in a water and lemon juice solution.
Fruit pies, custard tarts or similar wet mixtures
on top of uncooked pastry are only satisfactory if
there is a short delay period. Dishes containing
leftover cooked meat or poultry should not be
cooked automatically if there is a delay period.
• Where dishes may boil and spill over during
cooking, place them on a baking sheet.
Whole poultry must be thoroughly defrosted
before placing in the oven.
Check that meat and poultry are fully
cooked before serving.
Automatic cooking is not recommended for
baked items that require a pre-heated oven such
as cakes, cookies and breads.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Range
Multi-function oven
Convection oven
The left hand oven of your range is Multi-
function. It has many varied uses. We suggest
you keep a careful eye on your cooking until you
are familiar with each function. Remember - not
all functions will be suitable for all food types.
This function operates the fan and the heating
element around it. An even heat is produced
throughout the oven, allowing you to cook large
amounts quickly.
Fan oven cooking is particularly suitable for
multi-rack cooking and is a good ‘all-round’
function. It may be necessary to reduce the
temperature by approximately 20°F for recipes
previously cooked in a conventional oven.
If you wish to pre-heat the oven, wait until the
indicator light has gone out before inserting the
food.
Convection broiling
This function operates the fan whilst the top
element is on. It produces a more even, less
fierce heat than a conventional broiler. For best
results, place the food to be cooked, on a grid
over a roasting tin, which should be smaller than
a conventional broiler pan. This allows greater
air circulation. Thick pieces of meat or fish are
ideal for cooking in this way, as the circulated
air reduces the fierceness of the heat from the
broiler. The oven door should be kept closed
whilst cooking is in progress, so saving energy.
You will also find that the food needs to be
watched and turned less than for normal broiling.
Pre-heat this function before cooking.
Please remember that all ranges vary -
temperatures in your new ovens may differ to
those in your previous range.
Multi-function oven modes
Defrost
This function operates the fan to circulate cold
air only. No heat is applied. This enables small
items such as desserts, cream cakes and pieces
of meat, fish and poultry to be defrosted.
Defrosting in this way speeds up the process
and protects the food from flies. Pieces of meat,
fish and poultry should be placed on a rack, over
a tray to catch any drips. Be sure to wash the
rack and tray after defrosting.
Fan assisted oven
This function operates the fan, circulating air
heated by the elements at the top and the
base of the oven. The combination of fan and
conventional cooking (top and base heat) makes
this function ideal for cooking large items that
need thorough cooking, such as a large meat
roast. It is also possible to bake on two racks at
one time, although they will need to be swapped
over during the cooking time, as the heat at the
top of the oven is greater than at the base, when
using this function.
Defrost with the oven door closed.
Large items, such as whole chickens and meat
roasts should not be defrosted in this way. We
recommend this be carried out in a refrigerator.
Defrosting should not be carried out in a warm
oven or when an adjoining oven is in use or still
warm.
This is a fast intensive form of cooking; keep an
eye on the food cooking until you have become
accustomed to this function.
Ensure that dairy foods, meat and poultry are
completely defrosted before cooking.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Range
Handyrack
Conventional oven (top and
base heat)
This function combines the heat from the top
and base elements. It is particularly suitable for
roasting and baking pastry, cakes and biscuits.
Food cooked on the top rack will brown and
crisp faster than on the lower rack, because the
heat is greater at the top of the oven than at the
base, as in ‘Convection assisted oven’ function.
Similar items being cooked will need to be
swapped around for even cooking. This means
that foods requiring different temperatures can
be cooked together, using the cooler zone in the
lower half of the oven and hotter area to the top.
The maximum weight than can be held by the
Handyrack is 12lb (5.5kg). It should only be used
with the supplied meat tin, which is designed
to fit the Handyrack. Any other vessel could be
unstable. The base of the meat tin is shaped
to ease the draining of fat from the meat. Don’t
place the item to be cooked on a raised grid or
rack in the tin as it may be unstable.
Browning element
The Handyrack fits on the oven door. Food
cooking on it is easy to attend to, because it’s
accessible when the door is open. It can be fitted
at two different heights. One of the oven racks
must be removed and the other positioned to
suit.
This function uses the element in the top of the
oven only. It is a useful function for the browning
or finishing of pasta dishes, vegetables in sauce
and lasagne, the item to be browned being
already hot before switching to the top element.
When the Handyrack is used in its highest
position, other dishes can be cooked on the
bottom shelf position of the oven.
Base heat
This function uses the base element only. It will
crisp up your pizza or quiche base or finish off
cooking the base of a pastry case on a lower
rack. It is also a gentle heat, good for slow
cooking of casseroles in the middle of the oven
or for plate warming.
When the Handyrack is used in its lowest
position, other dishes can be cooked on the
second rack position of the oven.
To fit the Handyrack,
locate one side of it
on the door bracket.
The Browning and Base heat functions are
useful additions to your oven, giving you
flexibility to finish off items to perfection. With
use, you will soon realize how these functions
can combine to extend your cooking skills.
Then spring the
other side out to
clip it onto the other
bracket.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Range
To refit the rack, line up the rack with a groove
Oven racks
in the oven side and push the rack back until
the ends hit the rack stop. Lift up the front so the
rack ends clear the rack stops, and then lower
the front so that the rack is level and push it fully
back.
Steam
the rack guard should be at the back pointing upwards
As well as the flat racks some models are
supplied with drop racks The drop racks
increases the possibilities for oven rack spacing.
When cooking foods with high water content
(e.g. oven fries) there may be some steam
visible at the grille at the rear of the cooktop.
This is perfectly normal.
Oven light
fl a t r a c k
Press the appropriate button to turn on one of
the oven lights.
drop rack
The oven racks can be easily removed and
refitted.
If one of the oven lights fail, turn off the power
supply before you change the bulb. See the
‘Troubleshooting’ section for details on how to
change an oven light bulb.
Pull the rack forward until the back of the rack
is stopped by the rack stop bumps in the oven
sides.
Lift up the front of the rack so the back of the
rack will pass under the rack stop and then pull
the rack forward.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Range
Storage
The bottom drawer is for storing oven trays and
other cooking utensils.
It can get very warm, don’t store anything in
it which may melt or catch fire. Never store
flammable materials in the drawer. This
includes paper, plastic and cloth items, such as
cookbooks, plasticware and towels, as well as
flammable liquids. Do not store explosives, such
as aerosol cans, on or near the appliance.
Lift up the ends of the plastic clips (one each
side) to release the catches holding the drawer
to the side runners and at the same time pull the
drawer forward and away from the side runners.
For safety’s sake push the drawer runners back
out of the way.
Flammable materials may explode and result
in fire or property damage.
To refit the drawer
The drawer can be removed completely for
cleaning etc.
Pull out the side runners. Rest the drawer back
on the side runners and, keeping it level, push
it right back. The clips should click into position
holding the drawer to the side runners.
To remove the drawer pull it right out
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Range
Multi-function (Left hand) Oven cooking guide
Remember - not all modes will be suitable for all food types. The oven control settings and
cooking times given are intended to be used only as a guide. Individual tastes may require the
temperature to be altered to provide a preferred result.
Food is cooked at a lower temperature in a convection oven than in a conventional oven. When
using recipes, reduce the temperature by 20°F and the cooking time by 5-10 minutes. The
temperature in the convection oven is the same thoughout ensuring uniform results.
The racks should not be fitted directly one above the other. When cooking on more than one
rack always leave at least one runner space between them. Place baking sheets, individual
cake tins or baking dishes centrally on the oven rack. For best results pre-heat the oven until
the oven indicator light goes out.
Cooking chart - Fan assisted oven mode
Oven Rack
Food
Temp
340°F
Position
2-4
2-4
2-4
2-4
3
Approximate Cooking Time
Cup cake
20 min
Scone (British)
Deep apple pie
Plate tart
Fruit cake 8” x 3 1/2”
Puff pastry
Angel food cake
Brownies
350°F
350°F
375°F
225°F
425°F
325°F
350°F
350°F
350°F
350°F
15 min
45 min interchange after 25 minutes according to size.
45 min interchange After 25 minutes according to size.
1 hr 45 min - 2 hr
3 - 5
3
15-40 mins according to size. Interchange 2/3rds through cooking time
50 - 60 minutes
2-4
2-4
2-4
3
25 - 30 min interchange after 15 minutes
25 - 25 min interchange after 15 minutes
10 - 15 min interchange after 8 minutes
40 - 60 minutes
Muffins
Cookies
Pound cake
For roast meats and poultry refer to the Convection oven guide - reduce cooking time slightly.
Ensure meat and poultry is fully cooked before serving
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Range
Cooking chart
Conventional Oven
Convection Oven Approximate Cooking Time
Rack
Food
Temp
Position
Temp
FISH
375°F
375°F
375°F
3
3
3
350°F
350°F
350°F
Fillets 15-20mins.
Whole 10mins.per lb + 10mins.
Steaks according to thickness.
ROAST MEATS
Beef with bone
325°F
2-3
300°F
20-25mins. per lb + 20-25mins.
400°F
325°F
400°F
325°F
400°F
325°F
400°F
2-3
2-3
2-3
2-3
2-3
2-3
2-3
375°F
300°F
375°F
350°F
375°F
300°F
375°F
15-20mins. per lb + 15-20mins.
30-35mins. per lb + 30-35mins.
20-25mins. per lb + 20-25mins.
30-35mins. per lb + 30-35mins.
25-35mins. per lb + 25-30mins.
35-40mins. per lb + 35-40mins.
25-30mins. per lb + 25-30mins.
Beef without bone
Lamb
Pork
Stuffed and rolled - Add approx. 10 mins. per lb to above cooking times or cook at 390°F for 20mins. then 320°F for
remainder.
THOROUGHLY THAW FROZEN MEAT AND POULTRY BEFORE COOKING.
POULTRY
Chicken
325°F
400°F
325°F
400°F
2-3
2-3
1-3
1-3
300°F
375°F
300°F
375°F
20-25mins. per lb + 20-25mins.
15-20mins. per lb + 15-20mins.
20-25mins. per lb + 20-25mins.
15-20mins. per lb + 15-20mins.
Turkey
Stuffed Poultry - Cook at 390°F or at 390°F for 20mins. then 320°F for remainder. Prepacked (fresh or frozen) follow
packers cooking times
CASSEROLE
YORKSHIRE PUDDING
CAKES
300-325°F
425°F
2-3
4
300°F
400°F
2-4hrs according to recipe.
Large tin 30-35mins. Individual 10-20mins.
Rich fruit (7”)
Cup Cakes
300°F
375°F
425°F
2
275°F
350°F
400°F
21/2-3hrs.
3 & 5 or 3
2 & 4 or 3
15-25mins.
10-15mins.
Scones (British)
PASTRY
Plate Tart
375°F
375°F
375°F
425°F
425°F
230°F
2 & 4
2 & 4
4
350°F
350°F
350°F
400°F
400°F
225°F
45-50mins. Interchange after 25mins.
35-40mins. Interchange after 25mins.
15-20mins. according to size.
20-40mins. according to size.
20-30mins. according to size.
2-21/2hrs. according to size.
Fruit Pie
Tartlets
Puff Pastry
2,3 or 4
2 & 4
3
BREAD
MERINGUES
PUDDINGS
Baked Egg Custard
Baked sponge pudding
325°F
375°F
3
3
300°F
350°F
45mins.-1hr.
40-45mins. according to size.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Range
Cleaning your range
MAKE SURE THE FLOW OF COMBUSTION
Essential information
Before thorough cleaning isolate the electricity
supply. Remember to switch on the electricity
AND VENTILATION AIR TO THE RANGE IS
UNOBSTRUCTED -FOR EXAMPLE BY BUILD
OF FATS OR GREASE.
On Natural Gas the burners flames should be
a blueish color with, at most, a slight yellowish
fringe.
supply before use.
Never use paint solvents, caustic
cleaners, biological powders, bleach,
chlorine based bleach cleaners, coarse
abrasives or salt. Don’t mix different
cleaning products - they may react
together with hazardous results.
Recommended cleaning materials are
shown in the chart below.
On Propane gas the flames may be “softer”.
The cooktop burner flames may have a slight
yellowish tip.
If the flame burns with a long white tip you
should call for service.
Cleaning for spills
Cleaning the Range - Daily care
For spills and boil-overs that occur while
cooking, as soon as possible turn the burner off
and allow to cool. Do not clean until the area is
completely cooled down. Wipe up spills as soon
as possible.
Cleaning the range is not a welcomed chore,
but it has to be done to maintain efficiency and
appearance. Remember it is better to wipe up
any spills as they occur, this will prevent them
burning on and becoming more difficult to
remove later.
Do not allow surplus water to seep into the
range.
Cleaning chart
All Parts listed here can be cleaned using hot soapy water (dishwashing liquid detergent) and a soft
cloth. For more difficult cleaning, follow the appropriate instruction. Check cleaner manufacturers
guidelines for compatibility with the material of your range.
Part
Finish
How to clean
Burner Grates & Burner
Caps
Porcelain Enamel
Mildly abrasive cleaner such as Bon –Ami® or Soft Scrub®
Dishwasher.
Burner Head
Burner bases
Hotplate Top
Aluminum
Aluminum
Porcelain Enamel
Mildly abrasive cleaner and nylon scourer / soft cloth
As above.
Mildly abrasive cleaner such as Bon-Ami® or Soft Scrub®
with a soft cloth
Sides, Plinth
Control Panel
Oven liners, roof and floor,
door interior
Painted surface
Porcelain Enamel
Porcelain Enamel
Hot soapy water and soft cloth.
Non-abrasive cleaner, soft cloth.
Branded oven cleaner suitable for enamel surfaces.
Door Handles
Broiler Grid, Handyrack
Oven Racks
Chrome/Plastic
Chrome
Non-abrasive cleaner, hot soapy water, soft cloth
Dishwasher.
Hot soapy water and scouring pad.
Scouring Pad, hot soapy water.
Dishwasher
Mildly abrasive cleaner
Scouring Pad
Mildly abrasive cleaner such as Bon-Ami® or Soft Scrub®
with a soft cloth. Take care to not damage rubber door seal.
Multi-surface Cleaner, soft cloth
Meat tin
Porcelain Enamel
Porcelain Enamel
Porcelain Enamel
Porcelain Enamel
Broiler Pan
Door surround
Outer Doors and Drawer
Carefully read and follow the manufacturers instructions on cleaning products.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Range
When reassembling a Wok burner, turn over the
large base ring and find the ‘D’ shaped area.
Cooktop burners
Some models have a separate trim ring, which
fits on the burner head.
The burner heads and caps can be removed
for cleaning. Make sure they are absolutely dry
before replacing.
The central cooktop
Turn the head until the ‘D’ matches the one on
the burner base. Turn the head over and place it
on the burner base. To fit the small inner burner,
find the larger electrode notch in the burner rim.
Line this up with the white ignition electrode and
place the inner burner on the large base ring.
A cap, B head, C notch, D base, E electrode
When refitting the burner head, make sure that
the notch lines up with the electrode or hole in
the base. Check that the burner head is level
and that the cap is fitted centrally on the burner
head.
A
electrode notch
B
ignition electrode
Normal flame appearance
Burner not fitted correctly
Now fit the two trim rings, making sure that they
are sitting down properly.
The Wok burners
The Wok burners are a little more complicated
but they can also be taken apart for cleaning.
Broiler
The broiler pan and grid should be washed in
hot soapy water. After cooking meats or any
foods that soil, leave to soak for a few minutes
in the sink immediately after use. Stubborn
particles may be removed from the grid by using
a nylon brush.
Control Panel and Doors
Avoid using any abrasive cleaners including
cream cleaners, on brushed Stainless Steel
surfaces. For best results use a liquid detergent.
The control panel and control knobs should only
be cleaned with a soft cloth wrung out in clean
hot soapy water. Wipe with a clean dampened
cloth then polish with a dry cloth. The oven
doors should only be cleaned with a soft cloth
wrung out in clean hot soapy water.
Wok burner
A
C
E
inner burner cap,
inner burner head
Wok burner base
B
D
outer burner cap
outer burner head
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Range
Ovens
Troubleshooting
Steam is coming from the oven
Some of the oven lining panels can be removed
for cleaning and for cleaning behind. They can
also be put into a dishwasher. Remove the
racks first.
When cooking foods with a high water content
(e.g. oven fries) there may be some steam visible
at the rear grille. Take care when opening the
oven door, as there may be a momentary puff of
steam when the oven door is opened. Stand well
back and allow any steam to disperse.
The right hand fanned oven has a removable
oven roof - slide the roof liner forward and
remove.
The oven fan is noisy
The note of the oven fan may change as the oven
heats up - this is perfectly normal.
What cleaning materials are recommended for
the range?
See the ‘Cleaning’ section for a full list of
recommended cleaning materials. We do not
recommend corrosive or caustic cleaners as
these may damage your range.
The side panels of either oven can be removed.
Each side of the oven is fixed with four fixing
screws.You don’t have to remove the screws
to remove the oven linings. Lift each side panel
upwards and they will slide off the screws. Then
pull them forwards.
The knobs get hot when I use the oven or the
broiler, can I avoid this?
Yes, this is caused by heat rising from the oven
or the broiler, and heating them up. Don’t leave
the oven door open. Make sure that the broiler
pan is pushed right back to the ‘backstop’ when
broiling.
If there is an installation problem and I don’t
get my original installer to come back to fix it
who pays?
You do. Service organizations will charge for their
call outs if they are correcting work carried out by
your original installer. It’s in your interest to track
down your original installer.
Once the linings are removed, the oven enamel
interior can be cleaned.
Current Operated Ground Fault Circuit Breaker
Where the range installation is protected by a
30 milliamp sensitivity residual current device
(RCD), the combined use of your range and
other domestic appliances may occasionally
cause nuisance tripping. In these instances the
range circuit may need to be protected by fitting
100mA device. This work should be carried out
by a qualified electrician.
When replacing the linings fit the side linings
first.
Make sure you fit the oven roof with the slot at
the front.
Food is cooking too slowly, too quickly, or
burning
Cooking times may differ from your
previous oven. Check that you are using the
recommended temperatures and rack positions.
See pages 16 -17. The oven control settings
and cooking times are intended to be used
only as a guide. Individual tastes may require
the temperature to be altered either way, to get
the results you want. Try cooking at a higher
temperature setting. Is the oven roof in?
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Range
The oven is not cooking evenly
The oven light is not working
Do not use a tin or tray larger than 11 3/8” x 13”.
If you are cooking a large item, be prepared to
turn it round during cooking.
The bulb has probably burnt out.You can buy a
replacement bulb (which is not covered under
the guarantee) from a good electrical shop.
Ask for a 15w 125-130v lamp, FOR OVENS. It
must be a special bulb, heat resistant to 300°C
(570°F).
If two racks are used, check that space has
been left for the heat to circulate. When a baking
sheet is put into the oven, make sure it is placed
centrally on the rack.
Check that the door seal is not damaged and
that the door catch is adjusted so that the door
is held firmly against the seal.
Make sure the oven is cool. Open the oven door
and remove the Handyrack (if fitted) and oven
racks.
Turn off the power supply.
A dish of water when placed on the rack should
be the same depth all over. (For example, if it is
deeper at the back, then the back of the range
should be raised up or the front lowered). If the
range is not level arrange for your supplier to
level it for you.
Unscrew the bulb cover by turning counter
clockwise. Unscrew the old bulb. Screw in the
new bulb, screw back the bulb cover. Turn on the
electricity supply and check that the bulb now
lights.
Oven not coming on when turned on manually
Cooktop ignition or cooktop burners faulty
Is the power on? Is the clock illuminated? If not
there maybe something wrong with the power
supply.
Is the power on? Is the clock illuminated?
If not there may be something wrong with the
power supply. Is the range supply on at the
isolator switch?
See ‘power supply’ section further on.
Are the sparker (ignition electrode) or burner
slots blocked by debris?
Has the time of day been set?
Is the burner trim correctly located?
Are the burner caps correctly located?
See the section entitled ‘Cleaning’
If using the Multi-function oven have you set a
cooking function?
Is the key symbol ( ) showing in the display?
See the Clock section of the instructions for
more information on the key lock feature of the
clock.
Remember that each cooktop burner has a
special safety device that stops the flow of gas
if the flame goes out. When lighting a cooktop
burner the safety device has to be overridden
by holding the control knob so that the gas can
flow. This allows the flame sensor to heat up and
operate the safety device. Keep holding the knob
pressed in to let the gas through to the burner
for few seconds. The igniter should spark and
light the gas.
Oven not coming on when automatic cooking
Timer set correctly but oven knob left OFF by
mistake?
Is the key symbol ( ) showing in the display?
See the Clock section of the instructions for
more information on the key lock feature of the
clock.
If, when you let go of the control knob, the
burner goes out, the safety device has not held
in. Turn the control to the off position and wait
one minute, then try again this time holding in
the control knob for slightly longer.
If using the Multi-function oven have you set a
cooking function?
Oven temperature getting hotter as the range
gets older
If turning the knob down has not worked or only
worked for a short time then you may need
a new thermostat. This should be fitted by a
service person.
Cooktop burners will not light
If only one or all the cooktop burners will not
light, make sure that the parts have been
replaced correctly after wiping or removing for
cleaning.
Check that there is not a problem with your gas
supply.You can do this by making sure that other
gas appliances you may have are working.
Do the burners spark when you push the
button? If not check the power is on - is the clock
illuminated?
Broiler not cooking properly
Are you using the pan and grid supplied with the
range? Is the pan being used on the runners,
not the floor of the compartment? Is the broiler
tray pushed fully back to stop?
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your Range
If you are still having difficulty, contact : -
Service and spares
Technical Services Dept. Aga-Ranges Inc.
110 Woodcrest Road
Cherry Hill
Please complete the appliance details below
and keep them safe for future reference - this
information will enable us to accurately identify
your particular appliance and help us to help
you. Filling this in now will save you time and
inconvenience if you later have a problem with
your appliance. It may also be of benefit to keep
your purchase receipt with this leaflet.You may
be required to produce the receipt to validate a
warranty field visit.
NJ 08003
Telephone Number 1.866.4AGA.4USA
Email [email protected]
Please note
If your appliance is outside the warranty period,
our service provider may charge for this visit.
Fuel Type:
If you request an engineer to visit and the fault
is not the responsibility of the manufacturer, our
service provider reserves the right to make a
charge.
Dual Fuel
Name of Appliance & Color*
Appointments not kept by you may be subject to
a charge.
AGA Legacy 44
Out of Warranty
Appliance Serial Number *
Retailers Name & Address
We recommend that our appliances are serviced
regularly throughout their life to maintain the
best performance and efficiency.
Service work should only be carried out by
technically competent and suitably qualified
personnel.
Spare Parts
To maintain optimum and safe performance,
only use genuine spare parts. Do not use
re-conditioned or unauthorized gas controls.
Contact your retailer.
Date of Purchase
Installers Name & Address
Date of Installation
* This information is on the appliance data
badge.
If you have a problem
In the unlikely event that you have a problem
with your appliance, please refer to the rest
of this booklet, especially the problem solving
section, first to check that you are using the
appliance correctly.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions before installing or using this appliance.
Installation Instructions
Save these instructions for future reference.
Installation
This book contains many important safety messages.
Always read and obey all safety messages.
Installer: Leave these instructions with the appliance
27
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
If the information in this manual is not followed exactly, a fire or explosion may
result causing property damage, personal injury or death.
Do not store or use gasoline or other flammable vapors and liquids in the
vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance.
Do not touch any electrical switch
Do not use any phone in your building.
Immediately call your gas supplier from a neighbor’s phone. Follow the gas
supplier’s instructions.
If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer,
service agency or the gas supplier.
Warning
The anti-tip device supplied with this range must be correctly fitted when the
appliance is installed. This will reduce risk of tipping of the appliance from
abnormal usage or by excessive loading of the oven door
WARNING
• ALL RANGES CAN
TIP
• INJURY TO PERSONS
COULD RESULT
• INSTALL ANTI-TIP
BRACKET PACKED
WITH RANGE
• SEE INSTALLATION
INSTRUCTIONS
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Regulations
Page 30
Page 30
Page 30
Page 30
Page 31
Page 32
Page 33
Page 33
Page 35
Page 35
Page 35
Page 36
Page 38
Page 41
Page 44
Page 46
Page 48
Page 50
If you smell gas
Tools
Materials
Installation Safety Instructions
Dimensions and clearances
Location guidelines
Moving the Range
Checking the parts
Leveling the Range
Anti-Tip Device
Gas Connection
Electrical Connection
Assemble the range
Range operational checks
Conversion to another gas
Schematic diagram of the Range
Technical Data
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions before installing or using this appliance.
Installation Instructions
Save these instructions for future reference.
Regulations
Tools
Installation of this range must conform with local
codes, or in the absence of local codes, with the
National Fuel Gas Code, ANSI Z223.1/NFPA.54,
latest edition.
You will need the following tools
1. Electric drill
2. Masonry drill bit & anchors (only required if
fitting the range on a stone or concrete floor)
3. Steel tape measure
4. Phillips head screwdriver
5. Flat head screwdriver
6. 4mm & 3mm Allen keys
7. Spirit level
8. Pencil
9. Open-end or adjustable wrench
10. Pencil and ruler
In Canada, installation must conform with the
current Natural Gas Installation Code, CAN/
CGA-B149.1 or the current Propane Installation
Code, CAN/CGA-B149.2, and with local codes
where applicable.
This range has been design-certified by CSA
International according to ANSI Z21.1, latest
edition and CAN/CGA-22.2 latest edition.
Read the instructions before installing or
using this appliance. This range becomes hot
in use, the cooktop burners produce exhaust
gases. Take safety precautions - see the safety
warnings in the User Guide, which should be
read together with this installation guide.
11. Pipe wrenches
Materials
Additional materials you may need:
• Gas line shut-off valve
The range must be electrically grounded in
accordance with local codes or, in the absence
of local codes, in accordance with the National
Electrical Code (ANSI/NFPA 70, latest edition).
In Canada, electrical grounding must be
• Pipe joint sealant or UL-approved pipe thread
tape with Teflon* that resists action of natural
and LP gases. *Teflon: Registered trademark
of DuPont
in accordance with the current CSA C22.1
Canadian Electrical Code Part 1 and/or local
codes. See ‘Electrical Connection’ in this section.
• Flexible metal appliance connector (1/2’’ I.D.).
A 5-foot length is recommended for ease of
installation but other lengths are acceptable.
Never use an old connector when installing a
new range.
Important
• Observe all governing codes and ordinances.
• The range must be properly grounded.
• Save these instructions for the local electrical
inspector’s use.
• Flare union adapter for connection to gas
supply line (3/4’’ or 1/2’’ NPT x 1/2’’ I.D.)
• Flare union adapter for connection to pressure
regulator on range (1/2’’ NPT x 1/2’’ I.D.)
• To protect any floor covering under the range
a sheet of 1/4’’ thick ply wood or equivalent
large enough to stand the range on
For Your Safety
Do not store or use combustible materials,
gasoline or other flammable vapors and liquids
in the vicinity of this or any other appliance.
If you smell gas
• Open windows.
• Don’t touch electrical switches.
• Extinguish any open flame.
• Immediately call your gas supplier
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions before installing or using this appliance.
Installation Instructions
Save these instructions for future reference.
Caution
Installation Safety Instructions
Items of interest to children should not be stored
above a range - children climbing on the range
to reach items could be seriously injured.
Warning!
Improper installation, adjustment, alteration,
service or maintenance can cause injury or
property damage. Refer to this manual. For
assistance or additional information, consult a
qualified installer, service agency, manufacturer
(dealer) or the gas supplier. Never reuse old
flexible connectors. The use of old flexible
connectors can cause gas leaks and personal
injury. Always use NEW flexible connectors
when installing a gas appliance.
Converting to LP Gas
This appliance is supplied set for Natural gas.
A conversion kit for Propane gas is supplied with
the range.
If the appliance is to be converted this must be
done before installation. The conversion must
be performed by a qualified LP gas installer.
See the Conversion section at the back of this
installation manual for more details.
Important
Remove all packing material and literature
from oven before connecting gas and electrical
supply to range.
• Have your range installed by a qualified
installer.
• Your range must be electrically grounded
in accordance with local codes or, in the
absence of local codes, in accordance with
the National Electrical Code (ANSI/NFPA 70,
latest edition).
• Before installing your range on linoleum or
any other synthetic floor covering, make sure
the floor covering can withstand 180°F without
shrinking, warping or discoloring. Do not
install the range over carpeting unless a sheet
of 1/4’’ thick plywood or similar insulator is
placed between the range and carpeting.
• Make sure the wall coverings around the
range can withstand heat generated by the
range up to 200°F.
• Avoid placing cabinets above the range. There
must be a gap of at least 30’’ (76cm) between
the top of the range and any combustible
surface above it.
If a ventilating hood is installed above the range
follow the installation instructions supplied with
the hood.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions before installing or using this appliance.
Installation Instructions
Save these instructions for future reference.
A minimum space of 30” is required between the
top of the cooktop and a horizontal combustible
surface.
Dimensions and clearances
Provide adequate clearances between the
range and adjacent combustible surfaces. These
dimensions must be met for safe use of your
range. The location of the electrical outlet and
pipe opening (see Gas Pipe and Electric Outlet
Locations) may be adjusted to meet specific
requirements.
The maximum depth for cabinets installed above
cooktops is 13’’.
The standard depth of the range is 263/4’’ overall.
Positioning the Range
The diagrams below show the minimum
recommended distance from the range to
nearby surfaces.
If the range is to be installed between 24’’ deep
cabinets the optional rear spacer should be fitted
to move the range 2’’ forward. See the spacer
fitting instruction section of these instructions.
A Min 35-3/8’’(89.8cm) Max 36-7/16 (92.5cm)
B Min 43-5/16’’ (110cm)
for Canada Min 44-5/16” (112.5cm)
C Min 30’’ (76cm)
D Min 3’’ (7.5cm) but see below about door
opening.
E Min 50’’ (127cm)
F Min 18’’ (43cm)
G Maximum 13’’ (33cm)
The cooktop surround should be level with,
or above, any adjacent work surface. Above
cooktop level a gap of 3” should be left between
each side of the range and any adjacent vertical
surface.
For non-combustible surfaces (such as
unpainted metal or ceramic tiles) this can be
reduced to 1”.
Any range hood should be installed in
accordance with the hood manufacturer’s
instructions.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions before installing or using this appliance.
Installation Instructions
Save these instructions for future reference.
For safety reasons curtains must not be fitted
immediately behind the range.
200°F) by the range. (See the Installation Safety
Instructions section.)
We recommend a gap of 43-5/16” (110cm) (for
Canada 44-5/16” (112.5cm)) between units to
allow for moving the range.
Moving the Range
The range is very heavy. Take great care.
We recommend two people maneuver the range.
Ensure that the floor covering is firmly attached,
or removed to prevent it being disturbed when
moving the range around.You will need the
leveling tool.
If a flush fit is required (USA only), fit the range
up to the unit at one side then fit the unit the
other side.
A clearance of 5” (13cm) is required if the range
is near a corner of the kitchen to allow the oven
doors to open.
Pull the drawer out to its furthest point.
Location guidelines
Do not locate the range where it may be subject
to strong drafts. Any openings in the floor or wall
behind the range should be sealed. Make sure
the openings around the base of the range that
supply fresh air for combustion and ventilation
are not obstructed by carpeting or woodwork.
Lift up the ends of the plastic clips (one each
side) to release the catches holding the drawer
to the side runners and at the same time pull the
drawer forward and away from the side runners.
For safety’s sake push the drawer runners back
out of the way. Put the drawer somewhere safe
- do not refit it until you have completed the
installation, you will need access to the area
behind the drawer.
Your range is heavy and can settle into soft floor
coverings such as cushioned vinyl or carpeting.
Use care when moving the range on this type
of flooring. It is recommended that the following
simple and inexpensive instructions be followed
to protect your floor.
Fit the leveling tool on the rectangular adjuster
as shown below.
The range should be installed on a sheet of
plywood (or similar material). When the floor
covering ends at the front of the range, the area
that the range will rest on should be built up with
plywood to the same level or higher than the
floor covering.
This will allow the range to be moved for
cleaning or servicing. Also, make sure your
floor covering will withstand 180°F. (See the
Installation Safety Instructions section.)
Make sure the wall coverings around your
range can withstand the heat generated (up to
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions before installing or using this appliance.
Installation Instructions
Save these instructions for future reference.
LOWER THE FRONT ROLLER by doing 14
complete (360°) turns clockwise. (This means
turning and removing the leveling tool 56 times).
IMPORTANT!
Remove all tape and packaging. Make sure the
burners are properly seated and level. Take the
accessory pack out of the oven. Check to be
sure that no range parts have come loose during
shipping.
Now LOWER THE TWO REAR ROLLERS.
First fit the leveling tool on the hexagonal
adjusting nut as shown below.
Make 10 complete (360°) turns clockwise. (This
means turning and removing the leveling tool 20
times).
Make sure you lower BOTH REAR ROLLERS.
There are two adjusting nuts, one for each roller,
at both the front bottom corners of the range.
Note the rollers are only intended to aid
installation - the range should not be
moved once it is installed.
Push the range close to its final position, leaving
just enough space to get behind it.
Do not refit the storage drawer yet
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions before installing or using this appliance.
Installation Instructions
Save these instructions for future reference.
with the level placed diagonally first in one
direction and then the other.
Checking the parts
Check that the range has the following parts.
The rollers can be adjusted to level the range. To
adjust the height of the rear of the range use the
leveling tool supplied to turn the adjusting nuts
at the front bottom corners of the range.
4 grates
Broiler pan and trivet
Adjust the height of the front roller to level the
range. Turn clockwise to raise the range and
counter clockwise to lower.
When you are satisfied with the height and level
raise the front of the range by one turn of the
front roller adjuster. Screw down the front feet
to meet the floor. Screw the front roller adjuster
counter clockwise to raise the front roller so
that the front of the range is supported on the
feet, not the front roller, to prevent accidental
movement of the range.
Leveling tool
Handyrack
Leave the leveling tool in the storage drawer,
so that the customer can use it if they wish
to move the range.
Meat tin
6 oven racks
Anti-Tip Device
WARNING
Splashback & Plinth
Conversion kit from
Natural gas to LP gas
Range must be secured by Anti-Tip bracket
supplied. See instructions to install (supplied
with bracket). Unless properly installed, the
range could be tipped by leaning on the door.
Injury might result from spilled hot liquids or from
the range itself.
Installing the Anti-Tip Device
Rear spacer
The Anti-Tip bracket is supplied with instructions
for installation in a variety of locations. The
instructions include all necessary information
to complete the installation. Read the Safety
Instructions and the instructions that fit your
situation before beginning installation.
Leveling the Range
Place the range in its intended position taking
care not to twist it within the gap between the
kitchen units as damage may occur to the range
or the units. Install the oven shelves in the oven.
Check for levelness by placing a spirit level or a
cup, partially filled with water, on one of the oven
grids. If using a spirit level, take two readings-
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions before installing or using this appliance.
Installation Instructions
Save these instructions for future reference.
The range is designed to operate at a manifold
pressure of 4’’ of water column on natural gas.
A conversion kit for LP gas (propane or butane)
is supplied with the range. When converted to
LP gas, a pressure of 10’’ of water column is
required.
Gas Connection
Installation of this range must conform with local
codes or, in the absence of local codes, with the Na-
tional Fuel Gas Code, ANSI Z223.1-latest edition.
In Canada the range must be installed in accordance
with the current CGA Standard CAN/CGA-B149
- Installation Codes for Gas Burning Appliances and
Equipment and/or local codes.
Make sure you are supplying your range with the
correct type of gas.
If the range is to be used on LP gas, a qualified
LP installer must convert it. We recommend that
the range be converted before installation. This
must be done before the range can be used on
LP gas.
In The Commonwealth Of Massachusetts
This product must be installed by a licensed plumber
or gas fitter when installed within the Common-
wealth of Massachusetts.
A “T” handle type manual gas valve must be in-
stalled in the gas supply line to this appliance.
For proper operation, the pressure of natural gas
supplied to the regulator must be between 41/2’’
and 13’’ of water column.
Gas Supply Requirements
Recommended Gas Pipe Outlet Locations
For LP gas, the pressure supplied must be
between 10’’ and 13’’ of water column.
When checking for proper operation of the
regulator, the inlet pressure must be at least 1’’
greater than the operating (manifold) pressure
as given above.
The pressure regulator located at the inlet of the
range manifold must remain in the supply line
regardless of whether natural or LP gas is being
used.
A flexible metal appliance connector used to
connect the range to the gas supply line should
have an I.D. of 1/2’’ and be 5 feet in length for
ease of installation.
Opening inside the drawer cavity
Connect the Range to the Gas
Supply
Shut off the main gas supply valve before
disconnecting the old range and leave it off until
the new hookup has been completed. Don’t
forget to relight the pilot on other gas appliances
when you turn the gas back on.
Because hard piping restricts movement of
the range, the use of a CSA International-
certified flexible metal appliance connector is
recommended unless local codes require a
hard-piped connection.
Provide Adequate Gas Supply
Prior to installation, ensure that the local
distribution conditions (nature of the gas
and gas pressure) and the adjustment of the
appliance are compatible.
Never use an old connector when installing a
new range. If the hard piping method is used,
you must carefully align the pipe; the range
cannot be moved after the connection is made.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions before installing or using this appliance.
Installation Instructions
Save these instructions for future reference.
To prevent gas leaks, put pipe joint compound
on, or wrap pipe thread tape with Teflon*
around, all male (external) pipe threads.
Flexible Connector
*Teflon: Registered trademark of DuPont
A Install a manual gas line shut-off valve in
the gas line in an easily accessed location
outside of the range. Make sure everyone
operating the range knows where and how
to shut off the gas supply to the range.
B Install male 1/2’’ flare union adapter to the
1/2’’ NPT internal thread elbow at inlet of
regulator. Use a backup wrench on the
regulator fitting to avoid damage. When
installing the range from the front, remove
the 90° elbow for easier installation.
C Install male 1/2’’ or 3/4’’ flare union adapter
to the NPT internal thread of the manual
shut-off valve, taking care to backup the
shut-off valve to keep it from turning.
D Connect flexible metal appliance connector
to the adapter on the range. Position range
to permit connection at the shut-off valve.
E When all connections have been made,
make sure all range controls are in the off
position and turn on the main gas supply
valve. Use a liquid leak detector at all
joints and connections to check for leaks
in the system. Use a product specifically
manufactured for leak detection. Leak
testing of the appliance shall be conducted
in accordance to the manufacturer’s
Installer: Inform the consumer of the location
of the gas shut-off valve.
instructions.
CAUTION: DO NOT USE A FLAME
TO CHECK FOR GAS LEAKS.
When using test pressures greater than 1/2
psig (3.5kPa) to pressure test the gas supply
system of the residence, disconnect the range
and individual shut-off valve from the gas
supply piping. When using test pressures of
1/2 psig (3.5kPa) or less to test the gas supply
system, simply isolate the range from the gas
supply system by closing the individual shut-off
valve.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions before installing or using this appliance.
Installation Instructions
Save these instructions for future reference.
Connecting using the supplied
cord and plug
Electrical Connection
When installed the range must be
electrically grounded in accordance with
local codes or; in the absence of local
codes with the National Electrical Code
ANSI/NFPA 70, latest edition.
Your range is shipped with a 4-prong plug to be
used in a NEMA 14-50R receptacle.
Recommended Electrical Outlet Locations
In Canada the range must be installed
in accordance with the current CSA
Standard C22.1 - Canadian Electrical Code
Part 1.
Electrical Power Supply
Requirements
Electrical Requirements
When connecting using a NEMA 14-50R
receptacle, if possible position it so that it can
be accessed through the opening at the rear of
the drawer cavity. The range can then be easily
disconnected for servicing etc.
CAUTION: FOR PERSONAL SAFETY, DO
NOT USE AN EXTENSION CORD WITH
THIS APPLIANCE. REMOVE HOUSE FUSE
OR OPEN CIRCUIT BREAKER BEFORE
BEGINNING INSTALLATION.
Plug the range power cord into a properly
grounded wall receptacle.
This appliance must be supplied with the proper
voltage and frequency, and connected to an
individual, properly grounded branch circuit,
protected by a circuit breaker or time-delay fuse,
as noted on the rating plate.
Connecting if the supplied cord
and plug is not suitable.
Wiring must conform to National Electric Codes.
If the electric service provided does not meet the
above specifications, have a licensed electrician
install an approved outlet.
Because range terminals are not accessible
after range is in position, flexible service conduit
or cord must be used.
Provide Proper Electrical Supply
This range must be supplied with 240 volt, 60
Hz., and connected to an individual, properly
grounded branch circuit protected by a circuit
breaker or time-delay fuse (40 amp). If the
electrical service provided does not meet the
above specifications, it is recommended that a
licensed electrician install an approved outlet.
To remove the electrical connection cover first
remove the screws on the top and bottom edges.
The cover has two side and one bottom location
tags.
From January 1, 1996, the National Electric
Code requires that new construction (not
existing) utilize a 4-conductor connection to an
electric range.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions before installing or using this appliance.
Installation Instructions
Save these instructions for future reference.
NOTE: Do not install the conduit without a
squeeze connector.
Slide the cover down to free the side tags.
Fit the wires to the ground post and terminal
block
Free from the bottom tag.
When refitting the cover first locate it on the
bottom tag second locate the two side tags and
then replace the screws.
NOTE: Make sure the wires are completely
inserted into the terminals and secure
connections are made.
4-Wire Conduit Installation
Secure the squeeze connector in place in the
bracket by tightening the squeeze connector
screws.
Disconnect the supplied power cord from
the terminal block and ground post. Keep
the terminal block parts; you will need them.
Remove the strain relief clamp from the power
cord and remove the power cord and strain relief
clamp from the mounting bracket.
Refit the electrical connection cover.
Fitting a 3-Wire Power Cord
Disconnect the supplied power cord from
the terminal block and ground post. Keep
the terminal block parts; you will need them.
Remove the strain relief clamp from the power
cord and remove the power cord and strain relief
clamp from the mounting bracket. Discard the
strain relief clamp.
The range is shipped with reducer plates to
give a 1 1/8’’ diameter opening for conduit
connection. Find the reducer plates in the
conversion kit and fit them to the mounting
bracket.
NOTE: Do not install the power cord without
a strain relief - use the clamp supplied
with the cord.
Fit a squeeze connector (not supplied with
the range), to your conduit. Insert the conduit
through the reducer plates on the mounting
bracket. Allow enough slack to easily attach the
wires to the terminal block.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions before installing or using this appliance.
Installation Instructions
Save these instructions for future reference.
Refit the electrical connection cover
3-Wire Conduit Installation
Disconnect the supplied power cord from the
terminal block and ground post. Keep the
terminal block parts; you will need them. Remove
the strain relief clamp from the power cord and
remove the power cord and strain relief clamp
from the mounting bracket.
Fit the new strain relief device to the mounting
bracket by removing the two clamping screws,
feeding the two halves (ears first) through the
hole in the mounting bracket and loosely refitting
the screws. Insert the power cord through the
strain relief device but do not tighten the device
yet.
The range is shipped with reducer plates to give
a 1 1/8’’ diameter opening for conduit connection.
Find the reducer plates in the conversion kit and
fit them to the mounting bracket.
A Ground strap is supplied in the conversion
pack.
ground strap.
Fit the Ground strap to the ground and center
terminal of the connector block - see the figure.
Fit a squeeze connector (not supplied with
the range), to your conduit. Insert the conduit
through the reducer plates on the mounting
bracket. Allow enough slack to easily attach the
wires to the terminal block.
NOTE: Do not install the conduit without a
squeeze connector.
A Ground strap is supplied in the conversion
pack.
ground strap.
Fit the Ground strap to the ground and center
terminal of the connector block - see the figure.
The neutral or ground wire of the power cord
must be connected to the neutral terminal
located in the center of the connector block. The
power leads must be connected to the outside
terminals.
Make sure the connections are tight. Now
tighten the stain relief device to clamp the power
cord.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions before installing or using this appliance.
Installation Instructions
Save these instructions for future reference.
Assemble the range
Fit the Door Handles
Remove the 4mm Hex headed screws from the
doors with the hexagon key tool. Use the screws
to fit the door handles.
The handles should be above the fixings.
The neutral or ground wire of the power cord
must be connected to the neutral terminal
located in the center of the connector block. The
power leads must be connected to the outside
terminals.
Fit the plastic blanking plugs to the fixing holes.
NOTE: Make sure the wires are completely
inserted into the terminals and secure
connections are made.
Fit the Handrail
Secure the squeeze connector in place in the
bracket by tightening the squeeze connector
screws.
Remove the 4mm Hex headed screws from the
top corners of the fascia.
Seal the Openings
Seal any openings in the wall behind the range
and in the floor under the range when hookups
are completed.
When all Connections are
Completed
Fix the front handrail in position. Fit the plastic
blanking plugs to the fixing holes.
MAKE SURE THE FLOW OF COMBUSTION
AND VENTILATION AIR TO THE RANGE IS
UNOBSTRUCTED.
Fitting the rear spacer (optional -
but required for 24’’ deep cabinets)
Rear spacer.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions before installing or using this appliance.
Installation Instructions
Save these instructions for future reference.
The two end caps (one each end) of the
standard rear flue grille must first be removed.
Fit the new end caps to the rear spacer and flue
grille and hold in place with the nuts and spring
washers supplied.
They are held in place by two fixing nuts on the
inside face.
Screw the rear stays to the range back. Note:
the stays are of different lengths.
If you are not fitting the splashback the
splashback mounting holes can be blocked with
the extra screws supplied.
Remove the two fixing screws (3mm hexagonal
socket head) and nuts that pass through the top
of the rear flue grille.
Fit the splash back (optional)
If the rear spacer is not fitted.
Remove the two fixing screws (3mm hexagonal
socket head) and nuts that pass through the top
of the rear flue grille. Hold the splash back in
position.
Hold the spacer in position. From below the rear
flue grill use the 2 screws to fix the spacer in
position.
From the rear refit the 2 fixing screws and nuts.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions before installing or using this appliance.
Installation Instructions
Save these instructions for future reference.
If the rear spacer is fitted
Hold the splash back in position. From the rear
refit the 2 fixing screws and nuts.
Assemble the Grates
Each grate is different. Make sure that the grates
are in the correct position and sitting down.
Fit the plinth
Loosen the 3 screws along the front bottom
edge of the range. Hook the central keyhole over
the central screw. Twist and fit each end keyhole
over their respective screws. Tighten the fixing
screws.
Refit the storage drawer
To refit the drawer pull out the side runners.
Rest the drawer back on the side runners and,
keeping it level, push it right back. The clips
should click into position holding the drawer to
the side runners. Replace the drawer by locating
on side runners and push in.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICING - WARNING
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
The igniter should spark and light the gas.
Range operational checks
Keep holding the knob pressed in to let the gas
through to the burner for few seconds.
Oven check
If, when you let go of the control knob, the
burner goes out, the safety device has not held
in. Turn the control to the off position and wait
Set the clock to the time of day - the ovens will
not work if the clock is not set.
When the clock is first connected the display will
flash ( ) and ( ) alternately.
one minute, then try again this time holding in
the control knob for slightly longer.
Quality of Flames
On Natural Gas the burners flames should be
a blueish color with, at most, a slight yellowish
fringe.
On Propane gas the flames may be “softer”.
The cooktop burner flames may have a slight
yellowish tip.
To set the clock to read the time of day turn and
hold the Setting knob to the clock symbol (
)
If the flame burns with a long white tip you
should call for service.
and at the same time turn the Adjusting knob
left or right until the clock shows the time of day.
This is a 12 hour clock. Let go of the Setting
knob and it will spring back to the vertical ( )
oven manual setting.
Turn on the oven and check that the oven fan
starts to turn and that the oven starts to heat up.
Turn off the oven.
Normal flame appearance
Burner not fitted correctly
Broiler
MAKE SURE THE FLOW OF COMBUSTION
AND VENTILATION AIR TO THE RANGE IS
UNOBSTRUCTED.
Open the broiler compartment door. Turn on the
broiler control and check that the broiler heats
up.
MAKE SURE ALL CONTROLS ARE LEFT IN
THE OFF POSITION.
Oven Light
Press the oven light switches and check that the
lights are working.
Customer care
Please complete your details in the inside cover
of this Guide. Then replace this Installation
Guide back in the Customer Care Pack in the
correct position. Please inform the user how to
operate the range and hand over the Customer
Care Pack.
Note. The oven light bulbs are not included in
the guarantee
Check Ignition of Cooktop Burners
Operation of all cooktop burners should be
checked after the range and gas supply lines
have been carefully checked for leaks.
Thank you.
Check each burner in turn. There is a flame
safety device that stops the flow of gas to the
burner if the flame goes out. There is also a
spark ignition system that works when the knob
is pressed in.
For each burner, push in and turn a knob to the (
) lighting position.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICING - WARNING
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICING - WARNING
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
Valve adjustment
Conversion to another gas
Pull off all the control knobs. If the hand rail
This appliance is supplied set for Natural gas. A
has been fitted remove it - remove the plastic
conversion kit for Propane gas is supplied with
the range.
blanking plugs and remove the 2 end bracket
fixing screws.
If the appliance is to be converted this must be
done before installation. The conversion must
be performed by a qualified LP gas installer.
After conversion the installation must comply
with the relevant regulations and also the local
electricity supply company requirements. Read
the instructions before converting this appliance.
Remove the 2 cross headed screws that were
hidden by the hand rail end brackets.
Failure to convert the appliance correctly could
invalidate any warranty or liability claims and
lead to prosecution.
This instruction must be used in conjunction with
the rest of the appliance instruction, in particular
for information on Standards, range positioning,
connection hose suitability etc.
Open the oven door & or broiler door and
remove the fixing screws underneath the control
panel.
When servicing or replacing gas-carrying
components disconnect from gas before
commencing operation and check appliance is
gas sound after completion.
Lower control panel clear.
Do not use re-conditioned or unauthorised gas
controls..
Orifices
Standard burner
Wok burner
A valve bypass screw
Take out the bypass screw and replace with the
correct new screw on each gas control. Save the
screws removed from the appliance for future
use..
A orifice, B internal injector, C external injector
Remove burner caps and heads. Remove
old orifices, save the orifices removed from
the appliance for future use. Fit new orifices.
Reassemble in reverse order.
Valve Bypass screws
Natural Gas
Propane Gas
Wok burner
82
70
53
43
49
38
31
22
Large Burner
Medium Burners
Small Burner
Orifices
Natural Gas
Propane Gas
Wok burner
internal 110 internal 71
external 166 external 93
Gas Regulator
Large Burner
Medium Burners
Small Burner
170
150
107
106
Remove the storage drawer. Pull it out to its
furthest point.
84
61
46
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICING - WARNING
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
Pressure Testing
Connect the appliance to the gas supply. Check
the appliance is gas sound.
The gas pressure can be measured at one
of the central cooktop burner orifices. Lift off
a burner head. Fit the pressure gauge to the
orifice. Turn on the cooktop burner and turn on
and light one of the other burners.
Reassemble burner top, making sure it is
reassembled in the correct way on the burner
body.
Refit the storage drawer
To refit the drawer pull out the side runners.
Lift up the ends of the plastic clips (one each
Rest the drawer back on the side runners and,
side) to release the catches holding the drawer
keeping it level, push it right back. The clips
to the side runners and at the same time pull the
should click into position holding the drawer to
drawer forward and away from the side runners.
the side runners. Replace the drawer by locating
For safety’s sake push the drawer runners back
on side runners and push in.
out of the way.
Check the appliance is gas sound.
Check operation of all the burners.
The regulator is now accessible. Unscrew the
brass top of the regulator.
In the base of the brass top is a plastic snap in
converter device.
Natural gas
Propane gas
To convert the regulator snap the device out of
the top and refit the other way up. The snap in
converter device is marked to show which gas it
is set for. Make sure the device is secure in the
top cap and refit the cap to the regulator.
Stick on label
Stick the appropriate label on to the data badge
to indicate the gas the appliance is now set for.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions before installing or using this appliance.
Installation Instructions
Save these instructions for future reference.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions before installing or using this appliance.
Installation Instructions
Save these instructions for future reference.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions before installing or using this appliance.
Installation Instructions
Save these instructions for future reference.
Technical Data
This range is supplied set for Natural gas.
A conversion kit from NG to LP gas is included.
INSTALLER: Please leave these instructions with the User.
DATA BADGE LOCATION:
see installation instructions.
Inside base of drawer cavity - remove drawer. For removal of drawer
Country of Destination: USA/Canada
Gas
Natural Gas 4.0” W.C (10 mbar)
Propane 10.0” W.C (25 mbar)
Electric
240V 60Hz
(See appliance data badge for test pressures)
Dimensions
Overall height (splash not fitted)
Overall width
minimum 35 3/8” (89.8 cm)
43 5/16” (110cm) See ‘Positioning the Range’
maximum 36 7/16” (92.5 cm)
Overall depth without spacer
Overall depth with spacer
Space for fixing
26 3/4” (68cm).
28 3/4” (73cm)
See ‘Positioning the Range’
30” (76cm)
Minimum space above cooktop
Connections
Gas :
Electric:
1
”
240 V 60 Hz
/2 NPT at rear right-hand side
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all instructions before installing or using this appliance.
Installation Instructions
Save these instructions for future reference.
Orifices
A Wok burner
B Large Burner
C Medium Burners
D Small Burner
A valve bypass screw
Ratings
Natural Gas
Propane Gas
Orifice Screw
Orifice
Screw
Cooktop
Wok burner
15,000Btu/hr internal 110
external 166
82
15,000Btu/hr internal 71
external 93
49
Large Burner
Medium Burners
Small Burner
12,000Btu/hr
9,200Btu/hr
5,000Btu/hr
170
150
107
70
53
43
12,000Btu/hr
8,000Btu/hr
4,200Btu/hr
106
84
61
38
31
22
Gas burner inputs based on Gross Calorific Value
Ovens
Left hand Multifunction Oven
Right hand Fan Oven
Fan element
Top element
Browning Element
Bottom element
2.5kW
1.2kW
1.15kW
1.0kW
2.3kW
2.5kW
Broiler
Maximum total electrical load at 240V 7.4kW*
*approximate total including oven lights, oven fan etc.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Aga Ranges
110 Woodcrest Road
Cherry Hill, NJ 08003 USA
1.866.4AGA.4USA
Email [email protected]
Download from Www.Somanuals.com. All Manuals Search And Download.
|