IPPC-9151 Series
Rugged Industrial Panel PC with
Intel® Pentium® 4 or Celeron®
and 15" LCD Display
Users Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Class A
Note: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Opera-
tion of this equipment in a residential area is likely to cause harmful inter-
ference in which case the user will be required to correct the interference
at his own expense.
Warning! Any changes or modifications made to the
equipment which are not expressly approved by
the relevant standards authority could void your
authority to operate the equipment.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Packing List
Before setting up the system, check that the item is among those listed
below and is in good condition. If your Panel PC does not match any of
those below, please contact your dealer immediately.
1 x IPPC-9151 Panel PC
1 x Accessory pack, with:
• DESKTOP BRACKET(L)
• DESKTOP BRACKET(R)
• FIX Bracket x 4
• COMPRESSION SPRING x 4
• THERMAL GREASE
• Registration and 1 year Warranty card
• CD ROM for IPPC Series DRV
• Urethane Seal (UP/DOWN)
• Urethane Seal (L/R)
• Screw Bag
S/S D=5 H=1 + M3*5L ST Ni x 6
1/4R/S D=8.1 H=2.2 + #6-32*3/16"L ST Ni x 6
1/4R/S D=6.6 H=1.5 + M3*5L ST Ni x 8
ROUND M6*25 x 4
SP/S D=8 H=1.5 - M4*6L ST Ni x 8
The IPPC-9151 Series of Industrial Panel PCs includes the following
models:
IPPC-9151G-XAE
Rugged Pentium 4 Industrial Panel PC with 15" LCD,180W AC power
supply, Stainless steel chassis and aluminum front panel
IPPC-9151G-RAE
IPPC-9151G-XAE with resistive touchscreen
IPPC-9151 Series Users Manual
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
IPPC-9151F-XAE
Rugged Pentium 4 Industrial Panel PC with 15" LCD,180W AC power
supply, Stainless steel chassis and flat-sealed aluminum front panel
IPPC-9151F-RAE
IPPC-9151F-XAE with resistive touchscreen
Additional Information and Assistance
Step 1. Visit the Advantech web site at www.advantech.com where you
can find the latest information about the product.
Step 2. Contact your distributor, sales representative, or Advantech's
customer service center for technical support if you need addi-
tional assistance. Please have the following information ready
before you call:
• Product name and serial number
• Description of your peripheral attachments
• Description of your software (operating system, version, application
software, etc.)
• A complete description of the problem
• The exact wording of any error messages
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User's Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the
equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or let-
ting it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power
source to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according
to the user's manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE
THE STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR
ABOVE 60° C (140° F). THIS COULD DAMAGE THE EQUIPMENT. THE
EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT.
16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT
TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED
BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUC-
TIONS.
The sound pressure level at the operator's position according to IEC 704-1:1982 is
no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advan-
tech disclaims all responsibility for the accuracy of any statements contained
herein.
IPPC-9151 Series Users Manual
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Wichtige Sicherheishinweise
1. Bitte lesen sie Sich diese Hinweise sorgfältig durch.
2. Heben Sie diese Anleitung für den späteren Gebrauch auf.
3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie
Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch
zur Reinigung.
4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht
zugänglich sein.
5. Das Gerät ist vor Feuchtigkeit zu schützen.
6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen
oder Fallen könnte Verletzungen hervorrufen.
7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor über-
hitzung schützt. Sorgen Sie dafür, daB diese Öffnungen nicht abgedeckt wer-
den.
8. Beachten Sie beim. AnschluB an das Stromnetz die AnschluBwerte.
9. Verlegen Sie die NetzanschluBleitung so, daB niemand darüber fallen kann.
Es sollte auch nichts auf der Leitung abgestellt werden.
10. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu
beachten.
11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom
Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädi-
gung vermieden.
12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten
in das Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag aus-
lösen.
13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen
Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.
14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen
und von einer qualifizierten Servicestelle zu überprüfen:
a - Netzkabel oder Netzstecker sind beschädigt.
b - Flüssigkeit ist in das Gerät eingedrungen.
c - Das Gerät war Feuchtigkeit ausgesetzt.
d - Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert
oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.
e - Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
f - Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
15. VOSICHT: Explisionsgefahr bei unsachgemaben Austausch der Batte-
rie.Ersatz nur durch densellben order einem vom Hersteller empfohlene-
mahnlichen Typ. Entsorgung gebrauchter Batterien navh Angaben des
Herstellers.
16. ACHTUNG: Es besteht die Explosionsgefahr, falls die Batterie auf nicht fach-
männische Weise gewechselt wird. Verfangen Sie die Batterie nur gleicher
oder entsprechender Type, wie vom Hersteller empfohlen. Entsorgen Sie Bat-
terien nach Anweisung des Herstellers.
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000
beträgt 70dB(A) oder weiger.
Haftungsausschluss: Die Bedienungsanleitungen wurden entsprechend
der IEC-704-1 erstellt. Advantech lehnt jegliche Verantwortung für die
Richtigkeit der in diesem Zusammenhang getätigten Aussagen ab.
IPPC-9151 Series Users Manual
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Chapter 3 Jumper Settings &
Connectors 20
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
IPPC-9151 Series Users Manual
x
Download from Www.Somanuals.com. All Manuals Search And Download.
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
IPPC-9151 Series Users Manual
xii
Download from Www.Somanuals.com. All Manuals Search And Download.
1
General Information
This chapter gives background
information on the IPPC-9151 series
Sections include:
• Introduction
• Specifications
• Dimensions
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 General Information
1.1 Introduction
The IPPC-9151 seriesof industrial panel PCs is especially designed to fit
in space-limited environments where expansion is restricted. Its solid
structure enables systems to operate under harsh industrial conditions.
Sturdy structure
The whole system is protected by a firm solid structure. The front panel is
made of sturdy aluminum and has strengthened glass. It is shock resistant,
and complies with NEMA4/IP65. The stainless steel case (SUS304) on
the rear side is rugged and corrosion resistant, and enables the system to
operate reliably in even the harshest of environments.
Easy maintenance
A back door with lock is located right above the motherboard. Thus users
can easily maintain the CPU, HDD, SDRAM and CD-ROM drive. Jump-
ers can be easily set without removing a single screw. The lock protects
the system from intruders.
Economical
The PCM-9683 motherboard has Socket 478 architecture. It supports
Pentium 4 up to 2.8 GHz and Celeron up to 2.4 GHz. Socket 478 is an
economical yet powerful system. Its reliability enables the system to
operate faultlessly in industrial environments.
Friendly HMI
Systems in the IPPC-9151 series are equipped with a 15" LCD screen,
which provides high resolution display quality. The result is vivid, bright,
and sharp quality images. The panel PC is perfectly suited for Windows
OS. The touschscreen version enables simple operation, making the Panel
PC a solid industrial digital controller interface. In addtion, the rugged
design of the IPPC-9151 series offers 3 front panel options with alumi-
num/stainless/flat-seal for various requirements.
IPPC-9151 Series Users Manual
2
Download from Www.Somanuals.com. All Manuals Search And Download.
1.2 Specifications
1.2.1 General
• Dimensions (W x H x D):
Front Panel: 428 x 310 x 8 mm (16.85" x 12.2" x 0.31")
Cabinet: 402 x 290 x 162 mm (15.82" x 11.41"x 6.37")
Cut out dimension: 406 x 294 mm (15.98" x 11.57")
• Weight: 13 kg (28 lb)
• Power supply: 180 W
• Input voltage: 100 V AC ~ 240 V AC @ 50 ~ 60 Hz, 2A
• Output voltage: +5 V @ 15 A, +12 V @ 5 A, -12V @ 0.5A
• Disk drive housing:
Supports one 3.5" HDD, one slim size CD-ROM and FDD drive.
• Chassis:
Aluminum front frame complies with NEMA4/IP65. SUS304 stainless
steel back case
1.2.2 Standard PC Functions
• CPU:
Socket 478 Pentium 4 up to 2.8 GHz.
Celeron up to 2.4 GHz
• BIOS: Award 4 MB Flash BIOS, supports Plug & Play, APCI
• Chipset: Intel 845GV / ICH4
• 2nd level cache: On-die 256 or 512 KB
• RAM:
Two 184-pin DDR DIMM sockets up to 2GB DDR SDRAM
• PCI bus master IDE interface:
Supports two connectors. Each connector has one channel and supports
two IDE devices. Each channel supports PIO modes 0 ~ 4, DMA
modes 0 ~ 2, and Ultra DMA 33 simultaneously. The secondary con-
nector is designated for the CD-ROM drive. BIOS supports IDE CD-
ROM boot-up.
• Parallel port:
One parallel port, supports SPP/EPP/ECP parallel mode.BIOS config-
urable to LPT1, LPT2, LPT3 or disabled
3
Chapter1
Download from Www.Somanuals.com. All Manuals Search And Download.
• Serial ports:
Two serial ports with one RS-232 port (COM1) and one RS-232/422/
485 port (COM2). Both ports are compatible with 16C550 UARTs
• Universal serial bus (USB) port: Supports up to 4 USB (version 2.0)
ports.
• PCI bus expansion slots:
Two expansion slots for two PCI cards.
• Watchdog timer:
62-level, interval 1 ~ 62 seconds. Automatically generates system reset
or IRQ11 when the system stops due to a program error or EMI.
Jumperless selection and software enabled/disabled
• Battery: 3.0 V @ 195 mA lithium battery
1.2.3 AGP SVGA/Flat Panel Interface
• Chipset: Intel 845GV chipset with integrated Intel Extreme Graphics 2
for 2D/3D video accelerator
• Display memory: 8 MB share main memory
• Display type:
Simultaneously supports CRT and flat panel displays (TFT)
• Display resolution:
Supports LCD displays up to 1024 x 768 @ 262K in colors
1.2.4 Audio Function
• Chipset: Integrated in Intel 845GV ICH4 South Bridge
• Audio controller:
AC97 Ver.2.0 compliant interface, Multi stream, Direct sound and
Direct Sound 3D acceleration
• Stereo sound:
18-bit full-duplex codec
• Audio interface:
Microphone-in, line-in, line-out, and game ports MPU-401.
IPPC-9151 Series Users Manual
4
Download from Www.Somanuals.com. All Manuals Search And Download.
1.2.5 PCI bus Ethernet Interface
• Chipset: Intel RC82540Em local bus.
• Ethernet Interface:
Fully complies with IEEE 802.3u 100Base-T and 10 Base-T specifica-
tions. Includes software drivers and boot ROM
• 100/10Base-T auto-sensing capability
1.2.6 PCMCIA interface
• Chipset: RICOH R5C554
• Cardbus controller: A PC card controller offers a single chip solution as
a bridge between the PCI bus and the Cardbus
1.2.7 Analog Resistive Touchscreen (optional)
• Type: Analog resistive
• Resolution: 1024 x 1024
• Light Transmission:
75% (Gouge Hardness is greater than 4H per ASTM D3363-92 for
HCC01, HCG10 and HCG12)
• Controller: RS-232 interface
• Power Consumption: +5 V @ 200 mA
• Software Driver:
Supports DOS, Windows 3.1, Windows 98/ME/2000/XP and Win-
dows NT 4.0
1.2.8 Optional Accessories
• IPPC-9151G-RMKE
19" rack mounting kit for IPPC-9151 series.
1.2.9 Environmental
• Operating temperature: 0 ~ 50° C (32 ~ 122° F)
• Storage temperature: -20 ~ 60° C (-4 ~ 140° F)
• Relative humidity: 10 ~ 90% @ 40° C (non-condensing)
• Shock: 30 G peak acceleration (11 ms duration)
• Power MTBF: 100,000 hrs
• Certifications: CE, CCC, FCC Class, UL, BSMI
5
Chapter1
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3 Dimensions
Figure 1.1: IPPC-9151FA Dimensions
Figure 1.2: IPPC-9151GA Dimensions
IPPC-9151 Series Users Manual
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2
System Setup
This chapter details system setup for
the IPPC-9151 Series.
Sections include:
• General
• Installing SDRAM
• Installing a CPU
• Installing a 2.5" HDD
• Installing a CD-ROM Drive
• Installing Add-on Cards
• Mounting Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 System Setup
2.1 A Quick Tour of IPPC-9151
Before you start the computer, please follow these procedures to set up
the system.
1. Check and adjust jumpers on the motherboard (see Chapter 3)
2. Install SDRAM
3. Install a CPU
4. Install add-on cards
5. Connect the wires, cables and accessories
6. Mount the computer
7. Program the BIOS settings
8. Install an operating system.
Warnings
1. Switch off and unplug the computer every time
you access its interior.
2. The motherboard inside the system is composed
of many delicate ICs, chips and other integrated
circuit components. These components are easily
damaged by static shock. When you begin to
install components, please:
- Avoid touching metal parts of the motherboard.
- Wear an anti-static ring when handling a CPU or
SDRAM module.
- Put SDRAM modules and the CPU inside an
anti-static bag or a similar place before
installation.
IPPC-9151 Series Users Manual
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2.1: Side View
•
•
•
•
Figure 2.2: Bottom View
9
Chapter2
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1.1 PS/2 Mouse and Keyboard
If you wish to use a full-size desktop keyboard and PS/2 mouse with your
panel PC, follow these instructions:
1. Be sure the panel PC is turned off.
2. Attach the keyboard adapter to the 5-pin green port on the rear bottom
side of the rear cover.
3. Attach the mouse adapter to the 5-pin purple port on the rear bottom
side of the rear cover.
2.1.2 Parallel Port
The panel PC supports the latest EPP and ECP parallel port protocols for
improved performance and versatility with compatible printers or other
devices.
To connect the panel PC to a printer or other devices:
1. Make sure both the panel PC and the printer/devices are turned off.
2. Connect the 25-pin male connector of the printer cable to the 25-pin
female port on the panel PC labelled "parallel port."
3. If necessary, attach the other end of your printer cable to your printer,
and fasten any retaining screws.
4. Turn on the printer and any other peripheral devices you may have con-
nected to the panel PC. Then turn on the panel PC.
5. If necessary, run the panel PC's BIOS setup program to configure the
parallel port to respond as required by your printer and software operating
environment.
2.1.3 VGA port
An external VGA-compatible device may be connected to the system via
the 15-pin external port located on the rear of the system unit. The panel
PC simultaneously supports an external CRT monitor in addition to its
own LCD display.
IPPC-9151 Series Users Manual
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1.4 Serial COM ports
There are two serial COM ports on the bottom of the rear cover. You can
easily attach a serial device to the panel PC, such as an external modem or
mouse. Follow these instructions:
1. Make sure the panel PC and any other peripherial devices you may
have connected to the panel PC are turned off.
2. Attach the interface cable of the serial device to the panel PC's serial
port. (See Fig. 2-2.) If necessary, attach the other end of the interface
cable to your serial device. Fasten any retaining screws.
3. Turn on any other peripheral devices you may have connected to the
panel PC, and then turn on the panel PC.
4. Refer to the manual(s) which accompanied your serial device(s) for
instructions on configuring your operating environment to recognize the
device(s).
5. Run the BIOS setup program to set the I/O address and IRQ, and con-
figure the jumper settings to change the mode of the COM ports (refer to
section 3.3).
2.1.5 USB ports
An external USB device may be connected to the system via the 4-pin
USB ports located on the rear side of the system unit.
1. Connect the external device to the system.
2. The USB ports support hot plug-in connection. You should install the
device driver before you use the device.
2.1.6 Audio Interface
The audio interface includes three jacks: microphone-in, line-out and
line-in. Their functions are:
Microphone-in: Use an external microphone to record voice and sound.
Line-out:Output audio to external devices such as speakers or earphones.
The built-in speaker will not be disabled when the line-out jack is con-
nected to external audio devices.
Line-in: Input audio from an external CD player or radio.
1. Connect the audio device to the system.
2. Install the driver before you use the device.
11
Chapter2
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1.7 Ethernet
To install Ethernet for your system:
1. Connect the Ethernet cable.
2. Turn on the panel PC.
3. Under DOS, run \IPPC-9151\LAN\RSET8139.EXE to check hard-
ware network status before installing the Ethernet driver.
4. Run the Ethernet driver to connect up to the network.
2.1.8 Adjusting the LCD brightness
The brightness control key on the front panel allows you to adjust the
brightness of the LCD display panel. Its setting procedure is as follows.
1. If you want to extend the brightness, please press the OSD key until the
LED stops blinking. (See Pic. #1)
2. If you want to lower down the brightness, please press the OSD key
until the LED stops blinking. (See Pic. #2)
2.1.9 System turn ON/OFF
The IPPC-9151 series offers 2 system on/off options, which are:
1. Front Panel system on/off, which is the default setting.(pic)
2. Rear Cover system on/off. If you choose this one, you need to recon-
nect the cable. Please refer to the following procedures.
IPPC-9151 Series Users Manual
12
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2 Installing SDRAM
You can install from 64 MB to 2 GB (x2) of DDR SDRAM memory. The
Panel PC system provides one 184-pin DIMM (Double Inline Memory
Module) socket, and supports 2.5 V DDR SDRAM.
1. Unlock the back cover and open it.
2. Disconnect the FDD and CD-ROM cable.
3. Unscrew the screws of the FDD and CD-ROM module and take off the
FDD and CD-ROM.
13
Chapter2
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Disconnect the HDD cable.
5. Undo the seven screws of the HDD Module so you can install the
SDRAM.
IPPC-9151 Series Users Manual
14
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Push the two white eject levers on each side of the DIMM outward
until they are separated from the black vertical posts.
7. Insert the memory module into the socket at an angle of 90 degrees.
8. Push the two eject levers toward the vertical posts at each end of the
socket until the module is upright.
2.3 Installing a CPU
The CPU can be upgraded to improve system performance. The system
provides Socket 478 architecture which supports Pentium 4 CPU up to
2.8 GHz, and Celeron up to 2.4 GHz..
Warnings
Always disconnect the power cord from your panel
PC when you are working on it. Do not make con-
nections while the power is on, because sensitive
electronic components can be damaged by the
sudden rush of power. Only experienced electron-
ics personnel should open the panel PC.
1. Remove the HDD, FDD and CD-ROM module. The removal proce-
dure is the same as the SDRAM.
2. The CPU board will auto-detect CPU's voltage and frequency; there
are no jumper settings.
3. Open the CPU socket by pulling up the lever sideways from the socket,
then upwards at an angle of 90 degrees.
4. Insert the CPU with the correct orientation. The notched corner of the
CPU (with the white dot) should point toward the end of the lever. The
end of the lever is the blank area where one hole is missing from the cor-
ner of the square array of pin holes. An arrowhead printed on the mother-
board points to the end of the lever.
5. Slide the CPU in gently. It should insert easily. If not, pull the lever up
a little more and make sure the pins of the CPU correspond with the holes
of the socket. DO NOT USE EXCESSIVE FORCE!
6. Press the lever down. The plate will slide forward.
7. Place the heat sink on top of the CPU, and secure with heat sink clip.
8. Connect the CPU's cooling fan power connector.
9. Push the HDD, FDD and CD-ROM module bracket into the chassis.
15
Chapter2
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4 Installing a 3.5" HDD
You can attach one enhanced Integrated Device Electronics (IDE) hard
disk drive to IPPC-9151's internal controller which uses PCI local bus
interface. The following instructions are for installation:
1.
2.
Unlock the back cover and open it.
Remove the two screws and take off FDD, CD-ROM Module.
3.
Remove four screws and take off HDD bracket.
4.
5.
Insert the HDD into the bracket (see figure 2.4.3)
Put the HDD bracket into the Chassis and fasten the four screws.
Then attach the HDD flat cable and power cable.
IPPC-9151 Series Users Manual
16
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
Insert the FDD, CD-ROM Module and fix the back cover.
17
Chapter2
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5 Installing Add-on Cards
This system supports two PCI expansion cards.
1. Detach the five screws on the back to open the lid.
2. Take away the slot bracket.
3. Insert the add-on card, and put on the lid.
2.6 Mounting Instructions
There are two ways to mount the system: panel mounting or rack mount-
ing.
2.6.1 Panel Mounting
1. Take the four mounting brackets out of the accessory box.
2. Attach the four mounting brackets by inserting the screws into the
keyhole slots on the cover of the monitor.
3. Use the screws to secure the brackets to the cover. Tighten the screws
to secure the monitor to the back panel.
2.6.2 Rack Mounting
The monitor can be mounted to a 19" industrial rack with an optional
bracket.
IPPC-9151 Series Users Manual
18
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Jumper Settings
and Connectors
This chapter tells how to set up the
panel PC hardware, including instruc-
tions on setting jumpers and connecting
peripherals, switches and indicators. Be
sure to read all the safety precautions
before you begin the installation proce-
dures.
Sections include:
• Jumpers and Connectors
• CPU Installation
• CMOS Clear for External RTC (JP8)
• COM-port Interface
• Internal -12 V Source Selection Set-
ting (JP1)
• VGA Interface
• Watchdog Timer Configuration
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Jumper Settings &
Connectors
3.1 Jumpers and Connectors
3.1.1 Setting jumpers
You can configure your panel PC to match the needs of your application
by setting jumpers. A jumper is the simplest kind of electrical switch. It
consists of two metal pins and a small metal clip (often protected by a
plastic cover) that slides over the pins to connect them. To “close” a
jumper, you connect the pins with the clip. To “open” a jumper you
remove the clip. Sometimes a jumper will have three pins, labeled 1, 2,
and 3. In this case, you would connect either pins 1 and 2 or pins 2 and 3.
open
closed
closed 2-3
The jumper settings are schematically depicted in this manual as follows:.
1
2
1
2
3
1
2
open
closed
closed 2-3
A pair of needle-nose pliers may be helpful when working with jumpers.
If you have any doubts about the best hardware configuration for your
application, contact your local distributor or sales representative before
you make any changes.
PPC-154 User’s Manual
20
Download from Www.Somanuals.com. All Manuals Search And Download.
3.1.2 Jumpers and switches
The motherboard of the IPPC-9151 has a number of jumpers that allow
you to configure your system to suit your applications. The table below
lists the function of each of the board’s jumpers.
Table 3.1: Jumpers, switches and their functions
Label
Function
JP1
JP2
JP3
JP4
JP5
JP6
FSB (Front Side Bus) Setting
LCD Power Setting
Clear CMOS
COM2 RS232/422/485 jumper setting
COM1/COM2 pin 9 output type setting
PS2 Interface for touchscreen
Panel type setting
SW1
1
3.1.3 Jumper Locations
Figure 3.1: Jumpers on the IPPC-9151 motherboard
21
Chapter3
Download from Www.Somanuals.com. All Manuals Search And Download.
3.1.4 Connectors
Onboard connectors link the panel PC to external devices such as hard
disk drives or floppy drives. The table below lists the function of each of
the board’s connectors.
Table 3.2: Panel PC connectors
Label
Function
CN1
ATX 20 pin power connector
ATX 12V Power connector
LVDS connector 1
CN2
CN4
CN5
Invertor Power connector 2
LVDS connector 2
CN6
CN9
FDD Connector
CN15
CN16
CN17
CN24
CN25
FAN1
FAN2
PCI1
Internal Speaker Connector
EIDE HDD connector
CD-ROM Connector
IR connector
USB4/5 connector
CPU fan power connector
System fan power connector
PCI1 PCI bus expansion slot
PPC-154 User’s Manual
22
Download from Www.Somanuals.com. All Manuals Search And Download.
3.1.5 Locating connectors
Figure 3.2: Connectors on IPPC-9151 motherboard
23
Chapter3
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 CPU Installation
You can install an Intel Pentium 4 or Celeron CPU without setting any
frequency ratio or voltage.
Warning! To avoid damaging the computer, always turn off
the power supply before setting “Clear CMOS”.
Set the jumper back to “Normal operation” before
turning on the power supply.
Table 3.3: Front Side Bus Setting (JP1)
*Decided by CPU
Select 100 MHz
Select 133 MHz
1
1
2
2
3
3
1
2
3
1
2
3
*Default setting
3.3 CMOS Clear for External RTC (JP3)
This jumper is used to erase CMOS data and reset system BIOS informa-
tion.
The procedure for clearing CMOS is:
1.
2.
3.
4.
Turn off system.
Short pin 2 and pin 3.
Return jumper to pins 1 and 2.
Turn on the system. The BIOS is now reset to its default setting.
Table 3.4: CMOS clear (JP3)
*Normal operation
Clear CMOS
1
2
3
1
2
3
* default setting
PPC-154 User’s Manual
24
Download from Www.Somanuals.com. All Manuals Search And Download.
3.4 COM-port interface (JP4, JP5)
The panel PC provides two serial ports. COM1 (RS-232) and COM2 (RS-
232/422/485) in one COM port connector.
3.4.1 COM2 RS-232/422/485 setting (JP4)
COM2 can be configured to operate in RS-232, RS-422, or RS-485 mode.
This is done via JP6.
Table 3.5: COM2 RS-232/422/485 setting (JP4)
*RS-232
13
9
7
3
17 171515 13 1111
9
7
55
3 1
1
14
10
8
4
3
18 181616 14 1122 10
8
66
4 2
2
1
RS-422
17 15 13 11
17 15 13 11
9
9
7
7
5
1
5
3
18
14
10
8
4
18 161614 1122 10
8
66
5
4 2
2
1
RS-485
17 15 13 11
9
7
8
3
18 16 14 12 10
6
4
2
* default setting
The IRQ and the address ranges for COM 1 and 2 are fixed. However, if
you wish to disable the port or change these parameters later you can do
this in the system BIOS setup. The table overleaf shows the default set-
tings for the panel PC’s serial ports.
25
Chapter3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3.6: COM 1/2 Pin 9 setting (JP5)
Select 5 V
*Select Ring
1
2
3
1
2
3
* default setting
3.5 VGA interface
The panel PC's AGP VGA interface can drive conventional CRT dis-
plays. It is also capable of driving a wide range of flat panel displays,
including electroluminescent (EL), gas plasma, passive LCD and active
LCD displays.
3.5.1 LCD panel power setting
The panel PC's AGP SVGA interface supports 5 V and 3.3 V LCD dis-
plays. The LCD cable already has a built-in default setting. You do not
need to adjust any jumper or switch to select the panel power.
.
Table 3.7: LCD Panel Power Setting (JP2)
* Select 5V
Select 3.3V
1
2
3
1
2
3
*Default setting
PPC-154 User’s Manual
26
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Intel Chipset
This chapter provides information on
the Intel chipset configuration.
Sections include:
• Introduction
• Installation of chipset driver for
Windows 98/NT/ME/2000/XP
• Further Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Intel Chipset
4.1 Introduction
IPPC-9151 uses the 845GV chipset from Intel., with built-in high perfor-
mance 2D/3D Intel Extreme Graphics 2, flexible 100/133MHz system
bus settings, support for DDR266 SDRAM and multiple power saving
modes. This makes Intel 845GV the ideal integrated SMA chipset for the
Intel Pentium 4 and Intel Celeron processors.
The VIA VT82C686B PSIPC (PCI Super-I/O Integrated Peripheral Con-
troller) can support Intel and non-Intel based processor to PCI bus bridge
functionality to make a complete Microsoft PC99-compliant PCI/ISA
system, moreover, it also supports master mode enhanced IDE controller
with dual channel DMA engine (includes UltraDMA-33/66/100) and
interlaced dual channel commands.
4.2 Driver Installation
Before installing the driver, note the procedures below. You must know
which operating system you are using in your IPPC-9151, and then refer
to the corresponding installation flow chart. Then just follow the steps
described in the flow chart. You will quickly and successfully complete
the installation, even if you are not familiar with instructions for Win-
dows..
Important: 1. The following windows illustrations are exam-
ples only. You must follow the flow chart instruc-
tions and pay attention to the instructions which
then appear on your screen.
Notes:
1. The CD-ROM drive is designated as "D"
throughout this chapter.
2. <Enter> means pressing the "Enter" key on
the keyboard.
IPPC-9151 Series Users Manual
28
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2.1 Installation for Windows 98/NT/ME/2000/XP
1.
a. Select "Start", "Run”.
b. Enter the driver path "D:\IPPC-9151G& 9171G_DRV&Utility
\Chipset Software\IAA Driver\2.3\iaa23_multi.exe".
c. Click “OK”.
2. Press "Next" to continue the installation.
3. When you finish the IAA driver installation. Please continue to install
the INF driver. The driver path "E:\IPPC-9151G&
9171G_DRV&Utility\Chipset Software\INF
Driver\4.30.1006\infinst_autol.exe"
29
Chapter4
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3 Further Information
For further information about the AGP/VGA installation in your IPPC-
9151, including driver updates, troubleshooting guides and FAQ lists,
visit the following web resources:
Intel website:
www.intel.com
Advantech website:
www.advantech.com
If you need to know more details about installation, please refer to
\IPPC-9151G& 9171G_DRV&Utility\Chipset Software
IPPC-9151 Series Users Manual
30
Download from Www.Somanuals.com. All Manuals Search And Download.
5
PCI Bus Ethernet Inter-
face
This chapter provides information on
Ethernet configuration.
Sections include:
• Introduction
• Installation of Ethernet Driver for
Windows 98/NT/ME/2000/XP
• Further Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 PCI Bus Ethernet Interface
5.1 Introduction
The IPPC-9151series is equipped with a high performance 32-bit Ether-
net chipset, which is fully compliant with IEEE 802.3 100 Mbps CSMA/
CD standards. It is supported by major network operating systems, and is
also both 100Base-T and 10Base-T compatible.
The Ethernet port provides a standard RJ-45 jack. The network boot fea-
ture can be utilized by incorporating the boot ROM image files for the
appropriate network operating system. The boot ROM BIOS files are
combined with system BIOS, which can be enabled/disabled in the BIOS
setup.
5.2 Installation of Ethernet Driver
Before installing the Ethernet driver, note the procedures below. You
must know which operating system you are using in your IPPC-9151, and
then refer to the corresponding installation flow chart. Then just follow
the steps described in the flow chart. You will quickly and successfully
complete the installation, even if you are not familiar with instructions for
Windows.
Important: The following Windows illustrations are examples only. You
must follow the flow chart instructions and pay attention to the instruc-
tions which then appear on your screen.
Note 1:
Note 2:
The CD-ROM drive is designated as "D" through-
out this chapter.
<Enter> means pressing the "Enter" key on the
keyboard.
IPPC-9151 Series Users Manual
32
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2.1 Installation for Windows 98/NT/ME/2000
1.
a. Select "Start", "Run"
b. Enter the path, "D:\IPPC-9151G& 9171G_DRV&Utility
\Intel Lan 6.2\Setup.exe"
c. Click "OK"
a. Click "Next”
2.
3.
Read the license agreement and click "Yes" if you accept the terms
and wish to continue.
b. Click "Next"
33
Chapter5
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
a. Click "Next"
5.
a. Click "Install"
IPPC-9151 Series Users Manual
34
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
a. Click "Finish"
5.3 Further Information
Intel website: www.intel.com
Advantech website: www.advantech.com
35
Chapter5
Download from Www.Somanuals.com. All Manuals Search And Download.
IPPC-9151 Series Users Manual
36
Download from Www.Somanuals.com. All Manuals Search And Download.
2
6
VGA Setup
This chapter provides information on
the VGA setup.
Sections include:
• Introduction
• Installation of VGA Drivers
- for Windows 98/2000/ME
- for Windows NT
- for Windows XP
• Further Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 VGA Setup
6.1 Introduction
The IPPC-9151 has an onboard AGP flat panel/VGA interface. The spec-
ifications and features are described as follows:
6.1.1 Chipset
IPPC-9151 uses a 845G chipset from Intel for its controller. It supports
many popular LCDs, and LVDS LCD displays and conventional analog
CRT monitors. The 845G VGA BIOS supports color TFT and DSTN
LCD flat panel displays. In addition, it also supports interlaced and non-
interlaced analog monitors (color and monochrome VGA) in high-resolu-
tion modes while
maintaining complete IBM VGA compatibility. Digital monitors
(i.e. MDA, CGA, and EGA) are NOT supported. Multiple frequency
(multisync) monitors are handled as if they were analog monitors.
6.1.2 Display memory
The 845G chip can support 8MB frame buffer shared with system mem-
ory; the VGA controller can drive CRT displays or color panel displays
with resolutions up to 1024 x 768 @ 256K colors.
6.1.3 Display types
CRT and panel displays can be used simultaneously. The IPPC-9151 can
be set in one of three configurations: on a CRT, on a flat panel display, or
on both simultaneously. The system is initially set to simultaneous dis-
play mode. If you want to enable the CRT display only or the flat panel
display only, please contact Intel, or our sales representative for detailed
information.
IPPC-9151 Series Users Manual
38
Download from Www.Somanuals.com. All Manuals Search And Download.
6.2 Installation of the VGA Driver
Complete the following steps to install the VGA driver. Follow the proce-
dures in the flow chart that apply to the operating system that you are
using within your IPPC-9151.
6.2.1 Installation for Windows 95/98/ME
1.
a. Select "Start", "Run"
b. Enter the path "D:\IPPC-9151G& 9171G_DRV&Utility
\VGA\WIN9X_ME\SETUP.EXE”
Notes:
1. Installation for Windows 2000, please type
the path "D:\IPPC-9151G& 9171G_DRV&Utility
\VGA\Win2K_XP\Setup.exe"
2. Installation for Win NT, please type the path
"D:\IPPC-9151G& 9171G_DRV&Utility
\VGA\WinNT4\winnt4m1141.exe"
2.
Click "Next" on the Welcome screen.
39
Chapter6
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
Read the license agreement and click "Yes" if you accept the terms
and wish to continue.
4.
The driver files will now be installed. When the install finishes,
choose the "Yes." option to restart, and click "Finish" to restart
your computer. The driver will now be loaded.
6.3 Further Information
For further information about the AGP/VGA installation in your IPPC-
9151, including driver updates, troubleshooting guides and FAQ lists,
visit the following web resources:
Intel website:
www.intel.com
www.advantech.com
40
Advantech website:
IPPC-9151 Series Users Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Audio Setup
This chapter provides information on
the Audio setup.
Sections include:
• Introduction
• Installation of Audio Driver
- for Windows 98/2000/ME
- for Windows NT
- for Windows XP
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 Audio Setup
7.1 Introduction
The IPPC-9151's on-board audio interface provides high-quality stereo
sound and FM music synthesis (ESFM) by using the VIA VT82C686
audio controller from VIA. The audio interface can record, compress, and
play back voice, sound, and music with built-in mixer control.
The IPPC-9151 on board audio interface also supports the Plug & Play
(PnP) standard and provides PnP configuration for the audio, FM, and
MPU-104 logical devices. It is compatible with Sound Blaster™; Sound
Blaster Pro™ version 3.01, voice and music functions. The ESFM syn-
thesizer is register compatible with the OPL3 and has extended capabili-
ties.
7.2 Installation of the Audio Driver
Before installing the audio driver, please take note of the procedures
detailed below. You must know which operating system you are using in
your IPPC-9151, and then refer to the corresponding installation flow
chart. Just follow the steps in the flow chart. You can quickly and suc-
cessfully complete the installation, even though you are not familiar with
instructions for Windows.
Notes:
1. The windows illustrations in this chapter are
intended as examples only. Please follow the
listed steps, and pay attention to the instructions
which appear on your screen.
2. For convenience, the CD-ROM drive is desig-
nated as "D" throughout this chapter.
3. <Enter> means pressing the “Enter” key on
the keyboard.
IPPC-9151 Series Users Manual
42
Download from Www.Somanuals.com. All Manuals Search And Download.
7.2.1 Installation for Windows 98/ME/2000/XP
1.
a. Select "Start", "Run"
b. Enter the path "D:\IPPC-9151G& 9171G_DRV&Utility
\ALC202\WinXP_2K_Me_9X\Setup.exe"
Notes:
1. Installation for Windows 95, please Type the
path "D:\IPPC-9151G& 9171G_DRV&Utility
\ALC202\win95\Setup.exe"
2. Installation for Windows NT, please Type the
path "D:\IPPC-9151G& 9171G_DRV&Utility
\ALC202\winnt\Setup.exe"
2.
Click "Finish"
43
Chapter7
Download from Www.Somanuals.com. All Manuals Search And Download.
IPPC-9151 Series Users Manual
44
Download from Www.Somanuals.com. All Manuals Search And Download.
2
8
Touchscreen
This chapter contains information on
the touchscreen, its installation and
configuration.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8 Touchscreen
8.1 Introduction
The IPPC-9151 Series’ optional touchscreen uses advanced 8-wire resis-
tive technology. It provides more accurate sensing capacity than other
technologies. The touchscreen is specially designed for tough industrial
environments, and has been approved to FCC Class B standards.
8.2 Touchscreen Specifications
Electrical
• Contact bounce: < 10 ms
• Operating voltage: 5 V (typical)
• Sheet Resistance: 350 +/- 22% per Square.
• Linearity: <1.5% full scale linearity error in either direction.
• Insulation Resistance: >20 M @ 25VDC
Durability
• Test conditions: 4 H hardness, 0.04" stylus pen, 350 gram load
• Point activation:
1 Million activations on a single point with a 5/8" diameter silicone
finger with a 350g load at 2 Hz
• Character Activation Life:
>100,000 characters written within a 20 mm x 20 mm area on the touch
screen.
• Chemical resistance:
Hard coating is highly resistant to most solvents and chemicals
Optical
IPPC-9151 Series Users Manual
46
Download from Www.Somanuals.com. All Manuals Search And Download.
• Visible light transmission: 75% typical (>74% @ 550 nm test)
• Clarity: Clear Finish - 25%, Antiglare Finish - 15%
Sensor board
• Chemical strengthened glass with 4 H hardness standard.
(Test condition: ASTM D3363-92A)
Ball drop test
• Able to bear a 225 g steel ball dropped from 660 mm elevation without
breaking
Environmental Specifications
• Operating Temperature Range: -20° C ~ +50° C, 2 weeks at 50° C /
90% RH.
• Storage Temperature High: +70° C, 240 hours at ambient humidity.
• Storage Temperature Low: -40° C, continuous at ambient humidity.
• Accelerated Aging: 100 hours at 60° C / 95% RH.
• Thermal Shock: 25 cycles (one cycle is 30 min. dwell alternating from
-40 to +85° C with less than 10 min. transfer time.
8.3 Installing Driver for Windows 2000/XP
The touchscreen has drivers for Windows 2000 and Windows XP. You
should read the instructions in this chapter carefully before you attempt
installation.
Note 1:
Note 2:
The following windows illustrations are examples
only. You must follow the flow chart instructions
and pay attention to the instructions which then
appear on your screen.
Install the HMI CD Driver into the system
CD-ROM (D:\ means CD-ROM)
Before installing the Windows 2000/XP driver software, you must have
the Windows 2000/XP system installed and running on your computer.
47
Appendix8
Download from Www.Somanuals.com. All Manuals Search And Download.
You must also have one of the following PenMount Serial Interface con-
troller boards installed: 90A4, 9026B, 9036 or 9084. Contents of the Pen-
Mount Windows 2000/XP driver folder are listed below.
DMC9000.inf
DMC9000.sys
DMC9000.cat
SETUP.EXE
If you have an older version of the PenMount Windows 2000/XP driver
installed in your system, please remove it first. Follow the steps below to
install the PenMount Windows 2000/XP driver.
1.
When the system first detects the controller board, a screen appears
that shows “Unknown Device.” Do not use this hardware wizard.
Press Cancel.
IPPC-9151 Series Users Manual
48
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
Insert the PenMount Driver CD-ROM. Go to the Windows 2000-
XP Driver folder. Click setup.exe.
3.
The screen displays the installation wizard for the PenMount soft-
ware. Click “Next”.
49
Appendix8
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
A License Agreement appears. Click “I accept…” and “Next”
5.
The “Ready to Install the Program” screen appears. Select “Install.”
IPPC-9151 Series Users Manual
50
Download from Www.Somanuals.com. All Manuals Search And Download.
|
