Enclosure and Drive Cradle Overview
The drive enclosure is the enclosure where a SATA hard drive is mounted and
secured by 4 screws.
Drive cradle, also known as fixed tray, is the frame that mounts inside the drive
bay of a desktop, server or any computing equipment. The drive cradle provides
both power and data connection between the computer and the drive enclosure.
The Ruby cipher mobile rack fits into any standard 3 1/4” drive bay and can
connect to the computer via IDE or SCSI. The Ruby mobile rack is compatible
with all Ruby drive enclosures and Ruby cipher drive enclosures.
Addonics
T E C H N O L O G I E S
Top cover
IDE or SCSI
Interface
Ruby Cipher AES 256-bit Mobile Rack
RCMR256I & RCMR256SC
Switch
Drive cradle
Cipher Key
User’s Guide
Ruby Cipher key
Check to make sure you have the correct version
of the Ruby Cipher key. The key should match
the label at the back of the drive enclosure.
FCC Warning Statement
Black label AES-256 stands for Ruby Cipher 256-
bit key.
This equipment has been tested and found to comply with the limits for a class B digital
device pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy. If not installed and
used in accordance with the instructions, it may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If the equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment on and off, the user
is encouraged to try and correct the interference by one or more of the following
suggestions.
Ruby Enclosure
Switch
Reorient or relocate the receiving antenna
Increase the distance between the equipment and the receiver
Connect the equipment to a different power outlet other than the one where receiver is
connected
Power LED and
Drive Access LED
Cipher Slot
Consult a certified television or radio technician
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 5 Mount the board to the bottom
Step 2: Connect a 4-pin floppy power cable from your system’s power supply to
the 4-pin floppy power connector on the IDE bridge attached at the back of the
Ruby Cipher drive cradle. This power connection provides power to the ruby
cipher mobile rack.
cover.
Step 3: Slide the Ruby enclosure inside the cradle. Insert the Cipher key. To turn
ON the drive enclosure, place switch on INT position. Observe that the green
LED on the front of the enclosure lights up.
Note:
If the LED on the front of the Ruby Cipher enclosure lights up as red
color, turn of the system and reseat the cipher key. The LED must turn
on as green color indicating it is setup correctly.
Step 6 Put the top cover on by holding it in
near vertical position and sliding the two
metal clips inside the two small slots on the
rear of the bottom cover.
Model: RCMR256SC
Step 7 Lower the front of the top cover and making sure the two covers lined up
properly. Tighten the small retaining screw on the front of the bottom cover to
close the enclosure.
Cable Connections
Mounting holes for
3 ½” drive bay
Model: RCMR256I
Step 1: Connect the 68-pin SCSI ribbon cable that is connected to a SCSI
controller to the 68-pin SCSI connector attached at the back of the Ruby Cipher
drive cradle. This is the data connection for the device.
Step 2: Connect a 4-pin floppy power cable from your system’s power supply to
the 4-pin floppy power connector on the SCSI bridge attached at the back of the
Ruby Cipher drive cradle. This power connection provides power to the ruby
cipher mobile rack.
Mounting holes for
3 ½” drive bay
Step 1: Connect the 40-pin IDE ribbon cable that is connected to the IDE
controller on the motherboard to the 40-pin IDE connector attached at the back of
the Ruby Cipher drive cradle. This is the data connection for the device.
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3: Slide the Ruby enclosure inside the cradle. Insert the Cipher key. To turn
ON the drive enclosure, place switch on INT position. Observe that the green
LED on the front of the enclosure lights up.
Note:
If the LED on the front of the Ruby Cipher enclosure lights up as red
color, turn of the system and reseat the cipher key. The LED must turn
on as green color indicating it is setup correctly.
Be sure the Ruby cipher key is inserted into the drive enclosure prior to
turning on the power of the drive cradle. The hard drive will not be
detected by the computer if the power to the drive cradle is turned on
without the Cipher key. Under such condition, the power on the drive
cradle will have to be turned off and turned back on again with the
Cipher key already inserted into the drive enclosure in order to detect
the hard drive.
Technical Support
If you need assistance to get your unit functioning properly, please call Addonics
Technical Support. Our technical staff will be happy to assist you, but they will
need your help to do so. Calling the technical support staff without all the proper
information can be both time consuming and frustrating. Here are some tips to
help you out:
MODEL NUMBER – Please have this number on hand.
SYSTEM INFORMATION – Type of computer, peripherals, etc.
OPERATING SYSTEM – What version of Windows
WHAT’S THE TROUBLE? – Give enough information
about your problem so that we can recreate and diagnose it.
FREE Software Drivers for all Addonics Technologies
Products are available 24 hours per day at the
World Wide Web Site: www.addonics.com
Contact Information
Phone:
Fax:
408-573-8580
408-573-8588
Email:
TECHNICAL SUPPORT
Phone:
Hours:
Email:
408-453-6212
8:30 am - 6:00 pm PST
Download from Www.Somanuals.com. All Manuals Search And Download.
|