Addonics Technologies Network Cables NAS25HDU2 User Manual

T E C H N O L O G I E S  
User Guide  
Mini NAS Adapter  
(NAS25HDU2)  
v5.1.11  
Technical Support  
If you need any assistance to get your unit functioning properly, please have your  
product information ready and contact Addonics Technical Support at:  
Hours: 8:30 am - 6:00 pm PST  
Phone: 408-453-6212  
Download from Www.Somanuals.com. All Manuals Search And Download.  
I.  
Mini NAS Hardware Installation  
1.  
2.  
To open the mini NAS, remove  
the 2 screws located at the  
bottom part of the enclosure.  
Insert the SATA drive into the  
SATA connector and secure the  
drive using the screws  
provided.  
3.  
4.  
Connect LAN cable to uplink  
port to LAN switch and/or  
router.  
Connect 5V power adapter  
then power up the mini NAS.  
Network Link / Access LED  
On/Off Power Switch  
5V Power Jack  
USB Port for Printer Server  
Uplink Port to Router  
Factory Reset Button  
Mini NAS connected directly to a computer’s NIC card  
If you connect the mini NAS to a computer directly, the will act as a DHCP server,  
assigning itself an IP address automatically and will also assign an IP address to the  
computer’s network card. This configuration will not enable you to see the drive on  
the network.  
Mini NAS connected to a Router or Switch  
When the mini NAS is connected to a LAN network with an active DHCP server, it  
will obtain an IP address from DHCP server automatically. Or if your LAN network  
does not have an active DHCP server, mini NAS will immediately act as DHCP  
server and assign itself an IP address for installation  
II.  
Search mini NAS using SDisk Utility  
1.  
Browse the CD enclosed in the product package. Copy and paste  
“SDisk Utility” in to your computer then double click the icon to start  
search.  
Note: “SDisk utility” was written with JAVAscript, please make sure your computer  
has installed JAVA before, if not please install the JAVA JRE from the CD drive.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Support (M-F 8:30am - 6:00pm PST)  
Phone: 408-453-6212  
2.  
When mini NAS has been found, click “Connect” to enter web GUI  
utility.  
Open mini NAS web GUI by using web browser.  
1.  
2.  
Open web browser and type default host name “storage” in the  
search bar.  
Default login is “admin” for both User name and password. Click  
“OK” to enter configurations.  
Identification  
You can change and modify your host, group name and password from this page.  
Click “Apply” to save the setting.  
Host name: This is used to identify your device on the network. If you prefer  
a different name, type in the new name and click “Apply” to save setting.  
Group Name: This should be the same as your workgroup. In general, the  
default “WORKGROUP” will be OK. But if your workstation belongs to  
different workgroup, type in the correct group name to modify.  
For Window OS, right click on “My computer” and choose “Properties”, go to the  
computer name tab to see your current workgroup.  
If using a Mac OS system, to join a Windows workgroup, open the directory access  
utility (under Applications-> utilities). Select SMB and click configure to modify the  
settings (administrator access required to access this option.)  
Note: We strongly suggest you to change the password as soon as you  
logged in, to prevent unauthorized access.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Support (M-F 8:30am - 6:00pm PST)  
Phone: 408-453-6212  
LAN Configuration  
By default, “LAN Config” is set to “Automatic IP”. This will allow the mini NAS to  
obtain its IP address automatically. If you prefer setting it manually, select the static  
IP option, enter your own value and click “Apply” to confirm the new setting.  
Disk Utility  
In this page, you can manage hard disk settings of the USB storage device.  
Format: For first time installation, you need to format hard disk into FAT32  
file system. Formatting the drive will erase all data on the hard drive.  
Warning: For hard drives with data on it, create a backup before  
proceeding to format the hard drive!  
Tip: You can transfer back the backup data to the NAS Public folder for  
sharing via the network or USB connection of the USB Storage device.  
Sleep Time: This is to select hard disk sleeping mode.  
Scan Disk: After the scan, it will show file content information and health  
status for the hard disk.  
To access Samba PUBLIC folder of mini NAS in Windows  
Click on the Windows icon located on the bottom left corner of the screen, on the  
“Search programs and files” \\ followed by the IP address.  
Eg:\\192.168.1.121 and press Enter key to continue.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Support (M-F 8:30am - 6:00pm PST)  
Phone: 408-453-6212  
Type “Guest” as username. Leave password empty. Click on OK.  
This will direct you to the Public folder on the NAS drive.  
Now you have set up the folder that you wish to share on your NAS . This folder can  
be access from other computer on your local network.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Support (M-F 8:30am - 6:00pm PST)  
Phone: 408-453-6212  
Now you have set up the folder that you wish to share on your NAS . This  
folder can be access from other computer on your local network.  
To list the NAS drive in Network Places  
Go to Network Places in Windows XP, under Network Tasks, click on the “Set  
up a home or small office network”. Follow the wizard and once completed,  
reboot your system.  
For Vista and Windows 7, enable file sharing when accessing the NAS over  
the network.  
To access Samba PUBLIC folder of mini NAS in Ubuntu 8.04  
First, using the console get the prerequisites for the samba file system:  
$ sudo aptitude install samba smbfs  
$ mkdir /mnt/NAS  
$ sudo mount.cifs //NAS__IP_address/Public /mnt/NAS -o username=Guest  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Support (M-F 8:30am - 6:00pm PST)  
Phone: 408-453-6212  
To access Samba PUBLIC folder of mini NAS in Mac OS X  
1.  
2.  
3.  
4.  
Start at the "Go" drop down menu at the top of your screen,  
then click "Connect to server".  
Type into the "Server Address" field 'smb://' followed by the IP  
address of the mini NAS you want to connect.  
Click the "Connect" button in the bottom right corner of the  
window.  
Enter in a username and password. Click the "OK" button in the  
bottom right hand corner of the window to finish.  
Note: The workgroup name needs to be the workgroup the PC  
belongs to. If you don't know the workgroup that the PC  
belongs to you can find out by right clicking on the "My  
Computer" desktop icon on the PC, selecting "Properties" and  
then selecting the "Computer Name" tab. The workgroup name  
is about half way down the window.  
5.  
Select the "share" you are after. This simply refers to a  
particular group of shared files. Click "OK".  
CONTACT US  
Phone:  
Fax:  
408-573-8580  
408-573-8588  
Email:  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Support (M-F 8:30am - 6:00pm PST)  
Phone: 408-453-6212  

3M Respiratory Product FR M40 User Manual
ACR Electronics Marine GPS System RLB 40 User Manual
Aiphone Switch NBJ 20 User Manual
Airlink Network Card AWLL6080 User Manual
AO Smith Water Heater 318257 000 User Manual
AVerMedia Technologies TV Receiver MCE 2005 User Manual
Avocent Switch DSR1021 User Manual
Axor Indoor Furnishings 10129XX1 User Manual
Axor Plumbing Product 42270000 User Manual
BC Speakers Speaker 18TBX100 User Manual