Enclosure Overview
top cover
Addonics
shock
absorbers
T E C H N O L O G I E S
2.5” SATA
switch
hard drive
Ruby Combo Hard Drive
RCHDSAES & RCHDSAEU
PCB
bottom cover
User’s Guide
Step 1 Separate the top from the bottom cover of the drive enclosure by
loosening the screw as shown on the photo.
Version 1.0
FCC Warning Statement
This equipment has been tested and found to comply with the limits for a class B digital
device pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy. If not installed and
used in accordance with the instructions, it may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If the equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment on and off, the user
is encouraged to try and correct the interference by one or more of the following
suggestions.
Step 2 Align the SATA connector in the 2.5” hard drive with the SATA connector
on the PCB.
Step 3 Wrap the shock absorbers around the hard drive and PCB.
Reorient or relocate the receiving antenna
Increase the distance between the equipment and the receiver
Connect the equipment to a different power outlet other than the one where receiver is
connected
Consult a certified television or radio technician
Download from Www.Somanuals.com. All Manuals Search And Download.
Model: RCHDSAES
Model: RCHDSAEU
*Note: The Ruby combo hard drive with the eSATA interface must be connected
to a SATA controller with hot swap capability in order to add and remove drive
cartridge without rebooting. Please consult your motherboard or the add-in card
manufacturer to determine hot swap support on your SATA controller. All of the
Addonics SATA Host Controllers are hot swap capable.
For External Application:
For External Application:
eSATA cable
Power adapter
Step 1: Connect the eSATA cable to the eSATA port at the back of the
enclosure. The other end of the cable connects to the eSATA port on the USB2.0
to eSATA adapter. Plug the adapter to a USB port on your system.
eSATA cable
Power adapter
Red LED showing
adapter access
Step 1: Connect the eSATA cable to the eSATA port at the back of the
enclosure. The other end of the cable connects to an eSATA host controller.
eSATA cable from
Ruby enclosure
USB Port
Step 2: Plug into the power jack located at the back of the enclosure, the power
adapter. This power connection provides power to the ruby enclosure.
Green LED showing
adapter connectivity
Step 3: Set the switch to EXT position. The power LED will light up to indicate
power is provided to the drive.
Step 2: Plug into the power jack located at the back of the enclosure, the power
adapter. This power connection provides power to the ruby enclosure.
Step 3: Set the switch to EXT position. The power LED will light up to indicate
power is provided to the drive.
Download from Www.Somanuals.com. All Manuals Search And Download.
For Internal Application: (Applies to both models)
Technical Support
If you need assistance to get your unit functioning properly, please call Addonics
Technical Support. Our technical staff will be happy to assist you, but they will
need your help to do so. Calling the technical support staff without all the proper
information can be both time consuming and frustrating. Here are some tips to
help you out:
Drive
enclosure
MODEL NUMBER – Please have this number on hand.
SYSTEM INFORMATION – Type of computer, peripherals, etc.
OPERATING SYSTEM – What version of Windows
Drive
cradle
WHAT’S THE TROUBLE? – Give enough information
about your problem so that we can recreate and diagnose it.
FREE Software Drivers for all Addonics Technologies
Products are available 24 hours per day at the
Contact Information
Step 1: Connect a SATA cable to the 7-pin SATA data connector to the SATA
interface of the cradle.
Phone:
Fax:
408-433-3899
408-433-3898
Email:
Internet:
Step 2: Connect a 15-pin SATA power cable from your system’s power supply to
the SATA interface of the cradle. This power connection provides power to the
ruby drive cartridge system.
TECHNICAL SUPPORT
Phone:
Hours:
Email:
408-433-3855
8:30 am - 6:00 pm PST
Step 3: Slide the Ruby enclosure inside the cradle. To turn ON the drive
enclosure, place switch on INT position.
Download from Www.Somanuals.com. All Manuals Search And Download.
|