Enclosure and Drive Cradle Overview
The drive enclosure is the enclosure where a SATA hard drive is mounted and
secured by 4 screws.
Drive cradle, also known as fixed tray, is the frame that mounts inside the drive
bay of a desktop, server or any computing equipment. The drive cradle provides
both power and data connection between the computer and the drive enclosure.
The Diamond cipher drive cradle fits into any standard 5 ¼” drive bay and can
connect to the computer via SATA or USB 2.0. This interface allows hot
swapping the hard drive without restarting or rebooting the system. The Diamond
drive cradle is compatible with all Diamond drive enclosures and Diamond cipher
drive enclosures. As a result you can insert SATA or IDE hard drive, encrypted or
unencrypted, into the same drive cradle of a computer.
Addonics
T E C H N O L O G I E S
Diamond Cipher AES 256-bit Combo Hard Drive
Model: DCHD256ES & DCHD256EU
Drive
Power LED
Drive Activity
LED
User’s Guide
Drive Cradle
Cipher Key
Power Switch /
Locking Mechanism
FCC Warning Statement
Cipher Key Socket
This equipment has been tested and found to comply with the limits for a class B digital
device pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy. If not installed and
used in accordance with the instructions, it may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If the equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment on and off, the user
is encouraged to try and correct the interference by one or more of the following
suggestions.
Encryption key
active LED
Reorient or relocate the receiving antenna
Handle
Increase the distance between the equipment and the receiver
Connect the equipment to a different power outlet other than the one where receiver is
connected
Consult a certified television or radio technician
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4
Model: DCHD256EU
Turn the Diamond enclosure over with
the hard drive mounting holes facing
up. Use the included flat head screws
to secure the hard drive onto the
bottom of the enclosure and turn in
the screw to the “LOCK” position.
Connect the eSATA to eSATA cable to the eSATA connector located at the back
of the enclosure and the other end of the eSATA cable to the eSATA connector
on the USB2.0 to eSATA adapter. You can now plug the adapter to a USB port
on your system.
Powering On Enclosure: To power on the enclosure, move the switch located
at the back of the enclosure to the ON mode. When the switch is turned on, the
LED light beside it would light up to indicate power and also drive access.
Note: There are no drivers needed to use the eSATA cable as long as the
drivers are installed for the Serial ATA Controller card/chip. It is plug and play.
Cable Connections When Used as an External Hard Drive
Cable Connections When Used as an Internal Hard Drive
Note: Be sure the Diamond cipher key is inserted into the drive enclosure prior
to turning on the power of the drive enclosure. The hard drive will not be detected
by the computer if the power to the drive enclosure is turned on without the
Cipher key. Under such condition, the power on the drive enclosur will have to be
turned off and turned back on again with the Cipher key already inserted into the
drive enclosure in order to detect the hard drive.
Model: DCHD256ES
Power: Use either the 4-pin Molex or the 15-pin SATA power connector.
Do not use both power sources simultaneously.
Data:
Connect the SATA cable to the SATA connector located at the back of the drive
cradle and the other end to the SATA connector on your SATA host controller or
onboard SATA port.
LED cable: Only needed if you want to get drive access signal from the SATA
controller. Use the LED cable to connect the LED pin located at the back of the
cradle (beside the LED switch) to the LED jumper pins on your SATA host
controller or onboard SATA port to enable the drive activity LED.
Factory default, LED signal coming from hard drive.
Mini-Din power
connector
eSATA
connector
On / OFF
switch
Power: Connect the 6-pin Mini DIN power cable (provided) to the 6-pin Mini DIN
power connector located at the back of the enclosure.
Data:
Model: DCHD256ES
Connect the eSATA to eSATA cable to the eSATA connector located at the back
of the enclosure and the other end of the eSATA cable to the eSATA connector
on your SATA host controller with eSATA ports.
Download from Www.Somanuals.com. All Manuals Search And Download.
Powering On the Drive Cartridge System:
of the cradle (beside the LED switch) to the LED jumper pins on the SATA to
USB2.0 converter to enable the drive activity LED.
Note: Be sure the Diamond cipher key is inserted into the drive enclosure prior
to turning on the power of the drive cradle. The hard drive will not be
detected by the computer if the power to the drive cradle is turned on
without the Cipher key. Under such condition, the power on the drive
cradle will have to be turned off and turned back on again with the
Cipher key already inserted into the drive enclosure in order to detect
the hard drive.
Factory default, LED signal coming from hard drive.
Power Switch:
To power on the enclosure, use the key provided to turn the locking mechanism
on the drive cradle into the Lock position. When the switch is turned on, the
green LED located on the left side of the drive cradle would light up to indicate
power. The encryption key LED will also light up. The amber LED will blink if
there is drive activity.
Note: There are no drivers needed to use the eSATA cable as long as the
drivers are installed for the Serial ATA Controller card/chip. It is plug
and play.
Brand new hard drive must be partitioned and formatted first before a
drive letter is assigned by the OS. When a hard drive with data on it is
formatted with the Diamond cipher all the data will be erased.
Technical Support
Once the drive is detected by the system OS, the Diamond cipher key may be
removed from the drive enclosure. The encryption key LED will turn off but the
Diamond Cipher hard drive will continue operating normally (encrypting) till it is
removed from the system or powered off.
If you need assistance to get your unit functioning properly, please call Addonics
Technical Support. Our technical staff will be happy to assist you, but they will
need your help to do so. Calling the technical support staff without all the proper
information can be both time consuming and frustrating. Here are some tips to
help you out:
MODEL NUMBER – Please have this number on hand.
SYSTEM INFORMATION – Type of computer, peripherals, etc.
OPERATING SYSTEM – What version of Windows
WHAT’S THE TROUBLE? – Give enough information
about your problem so that we can recreate and diagnose it.
Model: DCHD256EU
Power: Using the 4-pin floppy connector of the Y-cable, connect it to the floppy-
type power connector on the converter. To provide power for the y-cable,
connect it to one of your desktop's 4-pin molex cable.
FREE Software Drivers for all Addonics Technologies
Products are available 24 hours per day at the World Wide Web Site:
Data:
Internal Connection
Use the USB 5-pin header cable to connect to the 5-pin connection on the
converter located below the USB Type B connector to the 5-pin USB connection
on your motherboard.
Contact Information
Phone:
Email:
Internet:
408-573-8580
Fax:
408-573-8588
External Connection
Use the USB Type A-B data cable to connect the converter to the USB port on
your system.
TECHNICAL SUPPORT
Phone:
Hours:
Email:
408-453-6212
8:30 am - 6:00 pm PST
LED cable: Only needed if you want to get drive access signal from the SATA to
USB2.0 converter. Use the LED cable to connect the LED pin located at the back
Download from Www.Somanuals.com. All Manuals Search And Download.
|