MODELS HW/HWB 300, 399, 420, 520, 610, 670
GAS-FIRED COMMERCIAL COPPER BOILERS FOR
HYDRONIC HEATINGAND HOT WATER SUPPLY
UP-FLOW MODELS
• INSTALLATION • OPERATION • MAINTENANCE • LIMITED WARRANTY
• INDOOR ONLY
WARNING: If the information in this manual
is not followed exactly, a fire or explosion
may result causing property damage,
personal injury or death.
— Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch;
CAUTION
do not use any phone in your
TEXT PRINTED OR OUTLINED IN RED CONTAINS INFORMATION
building.
RELATIVE TO YOUR SAFETY. PLEASE READ THOROUGHLY
BEFORE USING APPLIANCE.
• Immediately call your gas supplier
from a neighbor's phone. Follow the
gas supplier's instructions.
• If you cannot reach your gas supplier,
call the fire department.
— Installation and service must be
performed by a qualified installer,
service agency or the gas supplier.
ADIVISION OFA.O. SMITH CORPORATION
MC BEE, SC SEATTLE, WA
STRATFORD, ONTARIO
VELDHOVEN, THE NETHERLANDS
PLACE THESE INSTRUCTIONS ADJACENT TO BOILER AND
NOTIFY OWNER TO KEEP FOR FUTURE REFERENCE
PART NO. 211683-000 REV.02
SUPERSEDES PART NO'S, 210288-000 REV. 01 & 192356-000
PRINTED IN U.S.A. 0905
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE 3, RECOVERY CAPACITIES - CANADIAN MODELS ONLY
Input
Temp. (C)
11
20
17
30
22
40
26
50
33
60
39
70
44
80
50
90
56
100
1,001 1,001
291 264
1,464 1,331 1,220 1,127 1,046
387 352 322 298 276
1,542 1,401 1,285 1,186 1,101
407 370 339 313 291
1,909 1,735 1,590 1,468 1,363
504 458 420 388 360
2,239 2,035 1,866 1,722 1,599
592 538 493 455 423
61
110
67
72
78
Model (Btu/Hr.) Rise (F)
120
918
242
130
847
224
140
786
208
HW-300 300,000
HW-399 399,000
HW-420 420,000
HW-520 520,000
HW-610 610,000
LPH
GPH
LPH
GPH
LPH
GPH
LPH
GPH
LPH
GPH
5,505 3,670 2,753
1,455 970 727
7,322 4,882 3,661
1,935 1,290 967
7,708 5,138 3,854
2,036 1,358 1,018
9,543 6,362 4,771
2,521 1,681 1,261
11,194 7,463 5,597
2,958 1,972 1,479
2,202 1,835 1,573 1,376 1,223
582 485 416 364 323
2,929 2,441 2,092 1,831 1,627
774 645 553 484 430
3,083 2,569 2,202 1,927 1,713
815 679 582 509 453
3,817 3,181 2,727 2,386 2,121
1,008 840 720 630 560
4,478 3,731 3,198 2,799 2,488
1,183 986 845 739 657
3
Download from Www.Somanuals.com. All Manuals Search And Download.
FOREWORD
the locations indicated in the diagrams as these are necessary for checking
the operation of the boiler.
CAUTION
TEXTPRINTEDOROUTLINEDINREDCONTAINSINFORMATIONRELATIVE
TO YOUR SAFETY. PLEASE READ THOROUGHLY BEFORE USING MAKE SURETHE GAS ON WHICH THE BOILER WILLOPERATE IS THE
SAMEASTHATSPECIFIEDONTHEUNITRATINGPLATE.
APPLIANCE.
The boiler installation must conform to these instructions and the
Detailed installation diagrams are in this manual. These diagrams will serve
to provide the installer with a reference for the materials and method of requirements of the local authority having jurisdiction.
piping suggested. ITIS NECESSARYTHATALLWATERAND GAS PIPING
Where required by authority having jurisdiction, the installation must conform
to the Standard for Controls and Safety Devices for Automatically Fired
Boilers, ANSI/ASME CSD-1.
AND THE ELECTRICALWIRING BE INSTALLEDAND CONNECTEDAS
SHOWNINTHEDIAGRAMS.
CHECKTHEDIAGRAMSTHOROUGHLYBEFORESTARTINGINSTALLATION
TOAVOID POSSIBLE ERRORSANDTO MINIMIZETIMEAND MATERIALS
COST.
In absence of local code requirements, the boiler installation must conform
to the National Fuel Gas Code, ANSI Z223.1 and/or CAN/CSA B-149.1-00
Installation Codes.
This design complies with the latest edition of ANSI Z21.13.
CSA4.9 low-pressure boiler.
These manuals can be purchased from the CSA International, 8501 East
Pleasant Valley Road, Cleveland, OH 44131 or 178 Rexdale Boulevard,
Toronto, Ontario Canada M9W1R3.
Particular attention should be given to the installation of thermometers at
TABLE OF CONTENTS
PAGE
PAGE
START-UPAND OPERATING INSTRUCTIONS .................................. 45
Filling And Venting ...................................................................... 46
Pilot and Main Burner ................................................................. 46
Lighting Instructions ................................................................... 47-48
Pilot and Main Burner (Continued) ............................................. 49-51
Electronic Intermittent Pilot Ignition Control ................................. 51
Normal Operating Sequence With Honeywell S-8600H or
ROUGH-INDIMENSIONS ................................................................... 2-3
FOREWORD ......................................................................................
INSTALLATION INSTRUCTIONS ........................................................
Required Ability ..........................................................................
Installation As Boiler Replacement .............................................
Location ......................................................................................
4
4
4
4
5
Air Requirements ........................................................................ 5-6
S-8610M Intermittent Ignition Control (I.I.D.) ............................... 52
High Altitude Installations ........................................................... 52
Thermal Balancer ....................................................................... 52
Coil High Limit Control (Protector Switch) .................................. 52-53
Pressure Reducing Valve .......................................................... 53
Safety Flow Switch ................................................................... 53-54
Safety Relief Valve Maintenance ............................................... 54
Chemical Vapor Corrosion .........................................................
Installation Clearances ...............................................................
Levelling ......................................................................................
6
6
6
System Connections .................................................................. 6-9
Gas Connections ........................................................................ 9-11
Gas Pressure Regulators .......................................................... 11-12
Venting The Boiler - Standard Venting....................................... 12-14
Replacement Parts .....................................................................
REMOVAL OF EXISTING BOILER FROMACOMMON
54
Venting Maintenance - Standard Venting ..................................
Venting Sidewall (Optional) Power Vent System ...................... 15
Venting System .......................................................................... 15
15
VENTING SYSTEM ............................................................................ 54
GENERAL MAINTENANCE ................................................................ 55
Relief Valve ................................................................................
55
Safety Relief Valves .................................................................. 15-16
Wiring Connections .................................................................... 16-31
CLEANING AND FLUSHING INSTRUCTIONS .................................... 55
Internal Contaminants ................................................................. 55
Hot Water Supply Boilers - Preventive Maintenance ................ 55
Deliming ....................................................................................... 55-56
Deliming Solvents ....................................................................... 56
Heavy Lime Deposits ................................................................. 56
Removing Silicate ....................................................................... 56
Water Line Connections .............................................................
Hard Water .................................................................................
32
32
Tank Temperature Control .......................................................... 32-33
Low Water Cutoff ...................................................................... 33
Thermometers ............................................................................ 33
Drain Valve (Not Supplied) .........................................................
33
PRE-TROUBLE-SHOOTING ...............................................................
57
Closed Water System ................................................................ 33
TROUBLE-SHOOTING ....................................................................... 57-61
Piping Diagrams .......................................................................... 34-45 LIMITED WARRANTY ........................................................................ 62
INSTALLATION INSTRUCTIONS
REQUIRED ABILITY
With old systems where water temperature can be expected to
drop appreciably due to long standby periods, a bypass pipe of at
least 1" size with a balancing cock should be installed between
the boiler inlet and outlet. When the system first starts, the valve
should be slowly opened until the condensing ceases. This
adjustment remains at a permanent setting to establish required
temperature rise across the boiler.
INSTALLATION OR SERVICE OFTHIS BOILER REQUIRESABILITY
EQUIVALENT TO THAT OF A LICENSED TRADESMAN IN THE
FIELD INVOLVED. PLUMBING, AIR SUPPLY, VENTING, GAS
SUPPLY AND ELECTRICAL WORK ARE REQUIRED.
INSTALLATIONAS BOILER REPLACEMENT
Installation as boiler replacement on an old system with large
water volume may experience condensation within the boiler on
cold starts. This condensing of water vapor in the combustion
area can be prevented if a portion of the system water flow is
diverted past the boiler to cause an increase in boiler temperature
rise.
The equipment shall be installed in accordance with those
installation regulations in force in the local area where the
installation is to be made. These shall be carefully followed in all
cases. Authorities having jurisdiction shall be consulted before
installations are made.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
LOCATION
WARNING
FOR SAFE OPERATION PROVIDE ADEQUATE AIR FOR
COMBUSTION AND VENTILATION. AN INSUFFICIENT SUPPLY
OF AIR WILL CAUSE RECIRCULATION OF COMBUSTION
PRODUCTS RESULTING INAIR CONTAMINATION THAT MAY BE
HAZARDOUS TO LIFE. SUCH A CONDITION OFTEN WILL
RESULT IN A YELLOW, LUMINOUS BURNER FLAME, CAUSING
CARBONING OR SOOTING OF THE COMBUSTION CHAMBER,
BURNERS AND FLUE TUBES AND CREATES A RISK OF
ASPHYXIATION.
When installing the boiler, consideration must be given to proper
location. Location selected should be as close to the stack or
chimney as practicable with adequate air supply and as centralized
with the piping system as possible. This location should also be
such that the gas ignition system components are protected from
water (dripping, spraying, etc.) during appliance operation and
service (circulator replacement, control replacement, etc.).
THE BOILER MUST NOT BE INSTALLED ON CARPETING.
UNCONFINEDSPACE
THE BOILER SHOULD NOT BE LOCATED INANAREAWHERE IT
WILL BE SUBJECT TO FREEZING.
In buildings of conventional frame, brick or stone construction,
unconfined spaces may provide adequate air for combustion, and
draft hood dilution.
LOCATE IT NEAR A FLOOR DRAIN. THE BOILER SHOULD BE
LOCATED INANAREAWHERE LEAKAGE FROM THE BOILER OR
CONNECTIONS WILL NOT RESULT IN DAMAGE TO THE
ADJACENT AREA OR TO LOWER FLOORS OF THE STRUCTURE.
If the unconfined space is within a building of tight construction
(buildings using the following construction: weather stripping, heavy
insulation, caulking, vapor barrier, etc.) air for combustion,
ventilation, and draft hood dilution must be obtained from outdoors
or spaces freely communicating with the outdoors. The installation
instructions for confined spaces in tightly constructed buildings
must be followed to ensure adequate air supply.
WHEN SUCH LOCATIONS CANNOT BE AVOIDED, A SUITABLE
DRAIN PAN SHOULD BE INSTALLED UNDER THE BOILER. Such
pans should be fabricated with sides at least 60mm (2-1/2") deep,
with length and width at least 50mm (2") greater than the diameter
of the boiler and must be piped to an adequate drain. The pan
must not restrict combustion air flow.
CONFINEDSPACE
(a) U. S. INSTALLATIONS
WARNING
KEEPING BOILER AREA CLEAR AND FREE FROM COMBUSTIBLE
MATERIALS, GASOLINEAND OTHER FLAMMABLE VAPORSAND
LIQUIDS.
When drawing combustion and dilution air from inside a
conventionally constructed building to a confined space, such a
space shall be provided with two permanent openings, ONE
WITHIN 12 INCHES OF THE ENCLOSURE TOP AND ONE
WITHIN 12 INCHES OF THE ENCLOSURE BOTTOM. Each
opening shall have a free area of at least one square inch per
1000 Btuh of the total input of all appliances in the enclosure, but
not less than 100 square inches.
WARNING
THERE IS A RISK IN USING FUEL BURNING APPLIANCES SUCH
AS BOILERS IN ROOMS OR AREAS WHERE GASOLINE, OTHER
FLAMMABLE LIQUIDS OR ENGINE DRIVEN EQUIPMENT OR
VEHICLES ARE STORED, OPERATED OR REPAIRED.
FLAMMABLE VAPORS ARE HEAVY AND TRAVEL ALONG THE
FLOORAND MAY BE IGNITED BYTHE IGNITER OR MAIN BURNER
FLAMES CAUSING FIRE OR EXPLOSION. SOME LOCAL CODES
PERMIT OPERATION OF GAS APPLIANCES IF INSTALLED
18 INCHES OR MORE ABOVE THE FLOOR. THIS MAY REDUCE
THE RISK IF LOCATION IN SUCHANAREACANNOT BEAVOIDED.
If the confined space is within a building of tight construction, air
for combustion, ventilation, and draft hood dilution must be
obtained from outdoors. When directly communicating with the
outdoors or communicating with the outdoors through vertical
ducts, two permanent openings, located in the above manner,
shall be provided. Each opening shall have a free area of not less
than one square inch per 4000 Btuh of the total input of all
appliances in the enclosure. If horizontal ducts are used, each
opening shall have a free area of not less than one square inch
per 2000 Btuh of the total input of all appliances in the enclosure.
WARNING
FLAMMABLE ITEMS, PRESSURIZED CONTAINERS OR ANY
OTHER POTENTIAL FIRE HAZARDOUS ARTICLES MUST NEVER
BE PLACED ON OR ADJACENT TO THE BOILER. OPEN
CONTAINERS OF FLAMMABLE MATERIALMUSTNOT BE STORED
OR USED IN THE SAME ROOM WITH THE BOILER.
(b) CANADIAN INSTALLATIONS
Ventilation of the space occupied by the boiler(s) shall be provided
by an opening for ventilation air at the highest practical point
communicating with outdoors. The total cross-sectional area shall
be at least 10% of the area of the combustion air opening but in no
case shall the cross-sectional area be less than 10 square inches
(6500 mm2)
A hot water boiler installed above radiation level or as required by
the authority having jurisdiction, must be provided with a low water
cutoff device at the time of boiler installation.
In additional to the above, there shall be permanent air supply
opening(s) having a cross-sectional area of not less than 1 square
inch per 7,000 BTUH (310 mm2/KW) up to and including
1,000,000 BTUH plus 1 square inch per 14,000 BTU in excess of
1,000,000 BTUH. This opening(s) shall be located at, or ducted
to, a point neither more than 18" (450 mm) nor less than 6 inches
(150 mm) above the floor level.
AIR REQUIREMENTS
Provisions for combustion and ventilation air in accordance with
section 5.3, Air for Combustion and Ventilation, of the National
Fuel Gas Code, ANSI Z223.1, or sections 7.2, 7.3, or 7.4 of
CAN/CSA B149.1-00, Installation Codes, or applicable provisions
of the local building codes.
Where power vented equipment is used in the same room as the
boiler, sufficient air openings must be supplied.
Provisions for vent, bleed and gas relief lines (when applicable).
Keep appliance area free of combustible or flammable liquids.
Do not obstruct the flow of combustion or ventilating air.
UNDERSIZED OPENINGS MAY RESULT IN INSUFFICIENT AIR
FOR COMBUSTION.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE 4
Where an exhaust fan is installed in the same room with a boiler,
sufficient openings for air must be provided in the walls.
HWB/HW HWB/HW HWB/HW
HWB/HW HWB/HW
520 610 & 670
UNDERSIZED OPENINGS WILL CAUSE AIR TO BE DRAWN INTO
THE ROOM THROUGH THE CHIMNEY, CAUSING POOR
COMBUSTION. SOOTING MAY RESULT WITH AN INCREASED
RISK OFASPHYXIATION.
300
399
420
TOP 28" (711.2) 32" (812.8) 24" (609.6) 24" (609.6) 24" (609.6)
SIDES 6" (152.4) 6" (152.4) 24" (609.6) 24" (609.6) 24" (609.6)
REAR 6" (152.4) 6" (152.4) 24" (609.6) 24" (609.6) 24" (609.6)
VENT 6" (152.4) 6" (152.4) 6" (152.4) 6" (152.4) 6" (152.4)
CHEMICALVAPOR CORROSION
Two inch (50.8mm) clearance is allowable from combustible
construction for hot water pipes.
WARNING
CORROSION OF THE FLUEWAYS AND VENT SYSTEM MAY
OCCUR IF AIR FOR COMBUSTION CONTAINS CERTAIN
CHEMICALVAPORS WHICH BREAK DOWN INTOACIDSAT HIGH
TEMPERATURE. SUCH CORROSION MAY RESULT IN FAILURE
AND RISK OFASPHYXIATION.
Sufficient area should be provided at the front and rear of the unit
for proper servicing. Clearances of 24 inches (609.4mm) in the
rear and 48 inches (1,219mm) in the front are required by code. In
a utility room installation, the door shall be wide enough to allow
the boiler to enter or to permit the replacement of another appliance
such as a water heater.
Water boiler corrosion and component failure can be caused by
the heating and breakdown of airborne chemical vapors. Spray
can propellants, cleaning solvents, refrigerator and air conditioning
refrigerants, swimming pool chemicals, calcium and sodium
chloride, waxes, and process chemicals are typical compounds
which are corrosive. These materials are corrosive at very low
concentration levels with little or no odor to reveal their presence.
Products of this sort must not be stored near the boiler. Also, air
which is brought in contact with the water boiler should not contain
any of these chemicals. If necessary, uncontaminated air should
be obtained from remote or outside sources.
LEVELLING
Each unit should be checked after installation to be certain that it is
level.
If the unit is not level, insert metal shims under the legs of the unit
to correct this condition.
SYSTEM CONNECTIONS
INSTALLATION CLEARANCES
The system installation must conform to these instructions and to
the requirements of the local code authority having jurisdiction.
Good practice requires that all heavy piping be supported.
These boilers are approved for installation on combustible flooring
in an alcove with minimum clearance to combustibles of:
ATYPICALBOILER INSTALLATION
FIGURE1
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1. CONVENTIONAL INSTALLATIONS
All modern hydronic type boilers are exceptionally fast heating units.
The low water volumes in relation to firing rates require special
attention to water flow rates for smooth, efficient operation. These
considerations for the A. O. Smith copper heat exchanger boilers
are covered below.
Conventional 100C (200F) drop in systems for a fully loaded boiler
will maintain the following approximate flow rates:
U.S.
CANADIAN
MODELS
HWB-300
HWB-399
HWB-420
HWB-520
HWB-610
MODELS
HW-300
HW-399
HW-420
HW-520
HW-670
LPM
87
GPM
23
114
132
148
175
30
35
39
46
Figure 1 shows a typical installation of the boiler with pipe sizing
and circulator selected by the installer to provide adequate water
flow whenever the boiler is firing.
ONE BOILER INSTALLED
INDEPENDENT OF THE PRIMARY SYSTEM
FIGURE2
In a system with several large zones of which any might be smaller
than approximately 1/3 of the system should include a hydronic
balancer as shown in fig. 1. The balancer connects between the
system supply and the return line before the circulator inlet.
Adjustment of the balancing cock should permit adequate boiler
flow rate when only the smallest zone is in operation.
Total heating requirements for the building can be supplied by a
series of boiler loops all connecting to a common pipe joining the
system supply and return mains. The supply and return branches
of each boiler loop must join the common pipe only a short nipple
length apart. The different sets of branches should be installed
reasonably close together, but not necessarily to the short nipple
length as required for the supply and return of each set. These
branches may be made with tees or with welded connections.
Attention should be given to balancing inputs and water flow rates
where wide variations of system flow rates can occur.
The recommended minimum flow rates that will result in
approximately 300C (500F) temperature rise across the boiler are
as follows:
The installer is reminded that the total boiler flow rates need not
match the system flow rate.
TABLE 5
PUMPAND PIPE SIZING DATA
(PIPING FROM TEES IN MAIN TO BOILER BRANCHES)
U.S.
CANADIAN
MODELS
HWB-300
HWB-399
HWB-420
HWB-520
HWB-610
MODELS
HW-300
HW-399
HW-420
HW-520
HW-610
HW-670
LPM
34
45
53
61
GPM
9
12
14
16
Quantity and Model
Temp.
Rise°C (°F) G.P.M.
*Pump
Size
1-1/2"PR
150
125
100
60-13
1-1/2"HV
150
Pipe
Size
2"
1-1/2"
1-1/4"
1"
U.S
Canadian
10 (20)
15 (30)
15 (30)
20 (40)
10 (20)
15 (30)
20 (40)
20 (40)
10 (20)
15 (30)
20 (40)
20 (40)
10 (20)
10 (20)
17 (35)
20 (40)
10 (20)
15 (30)
17 (35)
20 (40)
23
15
15
11
30
20
15
15
32
21
16
16
39
26
23
20
51
34
29
25
69
76
18
20
HW-300
1 HWB-300
If system flow rate is unknown, or if zoning creates extreme
variations in flow rates, the boiler should be installed as shown
in fig. 2 for A. O. Smith LINEAR-TEMP installations.
2"
HW-399
HW-420
HW-520
HW-670
1 HWB-399
1 HWB-420
1 HWB-520
1 HWB-610
1-1/2"
1-1/2"
1-1/4"
2"
1-1/2"
1-1/2"
1-1/4"
2-1/2"
2"
1-1/2"
1-1/2"
3"
2-1/2"
2"
125
60-13
1-1/2"HV
150
2. LINEAR-TEMPINSTALLATIONS
A. New Installations
125
2-1/2"
1-1/2"HV
1-1/2"HV
150
60-13
2-1/2"
2"
A. O. Smith LINEAR-TEMP systems have been designed to provide
efficient, trouble-free operation of the boiler sizes covered in this
manual with any of the following conditions:
a. Unknown system flow rate
b. Varying flow rate as with zoned systems
c. Multiple boiler installations
1-1/2"HV
1-1/2"
Figure 2 shows piping and accessory arrangement for a boiler
pumped independent of the primary system mains. Pipe sizing
and boiler loop pump selection data are shown in Table 5 for
several different temperature rises across the boilers.
NOTE: Pipe loop sizes and pump selections based on
50 equivalent feet of pipe and fittings.
*All pump sizes listed are B & G model numbers.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
NO.
1
SUGGESTED ITEMS FOR INSTALLATION
Short pipe nipple and pair of boiler loop tees in piping
between system supply and return. One set per each
group of boilers
2
3
4
5
6
7
Boiler pipe loop. See piping sizing data above.
Boiler circulator. See pump sizing data above.
Thermometer.
Theraltimeter.
Plug cock to control flow rate.
Safety flow switches. For interlock with other systems or
instead of low water cutoff.
8
9
Relief valve.
With one -300, -399 or -420 item 9 is - sensing
element of remote control.
With a group of -300's, -399's or -420's, item 9 is - for
1st. boiler, the sensing element as above. For additional
boilers, install a 2nd. limit control if required by local codes.
With any -520, -610 or 670 boilers, install 2nd. limit control
here if required by local code.
SCHEMATIC OF THE LINEAR-TEMP® SYSTEM
FIGURE3
BOILER INLET - OUTLET SIZES
10 HWB-300 - 1-1/4", HWB-399 - 1-1/2", HWB-420-1-1/2",
HWB-520 & HWB-610 - 2". Canadian Models
10 HW-300 - 1-1/4", HW-399 - 1-1/2", HW-420-1-1/2",
HW-520 & HW-670 - 2". U.S. Models
Supply and return headers of the old system should be connected
to the boiler loop with a pair of tees set close together. The boiler
loop pump and the boiler(s) should be wired to operate only when
any of the system pumps are in operation. The number of zone
pumps that may be in operation at any particular time will take their
required flow rate out from the first tee in the boiler piping. This
water will be circulated through the proper branches from the supply
header to the zones calling for heat. The water will be brought
back to the return header and then into the second tee in the boiler
pipe loop. There will be no conflict between the boiler pump and
the zone pumps when the two tees in the boiler loop are placed
close together.
MINIMUM BRANCH SIZES TO BOILERS
11 HWB-300 - 1-1/4"
HWB-399 - 1-1/2"
HWB-420 - 1-1/2"
11 HW-300 - 1-1/4"
HW-399 - 1-1/2"
HWB-520, 610 (Single boiler
per pump) 2"
Canadian Models
HW-520, 670 (Single boiler
per pump) 2"
HW-420 - 1-1/2"
U.S. Models
12 Flow control valve. Required only if flow rate of system
primary is excessive for size of boiler branch tees or if
chilled water main is above boilers.
13 System supply temperature thermometer.
14 Boiler headers for three (3) boilers can be larger than pipe loop,
if desired, to aid in balancing.
Normal use of flow control valves is required to prevent cross
circulation of zones as with any multiple pump system. Flow control
is not required on boiler circuit.
The system flow rate is selected to give the desired system
temperature drop - depending on the design criteria.
Attention should be given to balancing gas inputs and water flow
rates. Large systems with multiple boilers should include main
water temperature control (with or without outdoor reset) to stage
the boilers on and off in relation to the load on the system.
The boiler generator flow rates, on the other hand, should be
selected to give the temperature rise through the generator that is
both economical and offers the best generator efficiency.
3. WATER SUPPLY LINE
The boiler temperature rise is normally between 100C and 200C
(200F and 400F). The system temperature that will be introduced
to the boiler (inlet temperature) plus the selected boiler temperature
rise selected from PUMPAND PIPE SIZING DATAshould not exceed
the high limit control setting of 1150C (2400F).
These boilers can be used ONLY in a forced circulation hot water
heating system. Since most forced circulation systems will be of
the closed type, install the water supply line as shown on piping
diagrams, fig. 1 or 2.
Fast filling of large pipe, old radiator installations and pressure
purging of series loop systems (where high pressures are not
available) requires bypassing of the pressure reducing valve.
Generally, pressure purging is not possible with a well pump
system. High point air venting is essential.
There should be a relation of the minimum system load to the size
boiler selected as the first firing or base boiler. This will stabilize
operation during minimum load periods.
B. Commercial Boiler Replacements
If the system is of the open type, a pressure reducing valve will not
be required as the water supply to the system will be controlled by
a manually operated valve. An overhead surge tank is required.
Application of LINEAR-TEMP® to a commercial boiler replacement
with an old multiple pump installation is an excellent way to
modernize the system. The A. O. Smith boiler(s) should be
installed on a pipe loop with a separate circulating pump selected
from PUMPAND PIPE SIZING DATATABLE.
4. EXPANSION TANK
CAUTION
Figure 3 shows a line drawing of how the system headers should
be connected to the pipe loop installed with the replacement
boiler(s). Make-up water connections and accessories are not
shown.
A closed system will exist if a check valve (without bypass), pressure
reducing valve (without bypass), or a water meter (without bypass)
is installed in the cold water line between the water heater and
street main (or well).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
If the boiler is connected to chilled water piping or its heating coils
are exposed to refrigerated air, the boiler piping system must be
equipped with flow valves or other automatic means to prevent
gravity circulation through the boiler during the cooling cycle.
Excessive pressure may develop causing premature tank failure
or intermittent relief valve operation. This is not a warranty failure.
An expansion tank or a similar device may be required in the inlet
supply line between the appliance and the meter or valve to
compensate for the thermal expansion of water under supply
pressure, see figure 1.
8. CIRCULATING PUMP
CONSTANT CIRCULATING PUMP OPERATION OF THE BOILER
VOIDS THE WARRANTY. Constant water flow through the unit will
“wash” away the copper’s natural protective coating. This is called
velocity erosion. This erosion is not as great a problem when
intermittent circulating operation is used per the recommended
installation procedure. Constant circulation of water through the
building’s system main is permissible as long as the water does
not constantly flow through the boiler. Only all bronze or stainless
steel circulators are to be used with the unit when it is installed in
HOT WATER SUPPLY SYSTEMS.
An air separator as shown in the piping diagrams is recommended
especially for modern commercial hydronic systems.
5. VENTVALVES
It is recommended that automatic, loose key or screwdriver type
vent valves be installed at each convector or radiator.
6. MANIFOLD HEADERS
Split systems with individual supply and return lines from the boiler
room should normally have this piping connected to supply and
return manifold headers near the boiler. To achieve good water
distribution with maximum pressure drop for several circuits,
manifolds of at least 2-1/2" (64mm) diameter are suggested on
HWB/HW-399, HWB/HW-420, HWB/HW-520, HWB/HW-610 and
HW-670 units. HWB/HW-300 units should have 1-1/2" (38mm)
diameter manifolds.
The circuits should be spaced on the header at a minimum of
3" (76mm) center to center. Install a balancing cock in each return
line.
ATYPICALCIRCULATING PUMP
FIGURE5
Manifold headers are recommended for split systems with or
without zone valves and also those installations with zone
circulators. If the system is to be split at remote points, good
practice requires special attention be given to main pipe sizing to
allow balancing of water flow.
Although each circulator that requires oiling is oiled and operated
by the manufacturer, IT MUST BE OILED AGAIN BEFORE
OPERATED. Oil the three oil cups (2 on the motor, 1 on the pump)
as instructed on the oil tube supplied with the unit, fig 5.
Thereafter, during the heating season, lubricate the three oil cups
at least once every four months. Combination heating-cooling
systems should be lubricated every four months year ‘round.
The boiler piping system of a hot water boiler connected to heating
coils located in air handling units where they may be exposed to
refrigerated air circulation must be equipped with flow control valves
or other automatic means to prevent gravity circulation of the boiler
water during the cooling cycle.
Use 2 or 3 teaspoonsful in bearing oil cups, fig. 5, and 10 or
12 drops in the motor oil cups. Use No. 20 non-detergent motor
oil.
7. COOLING PIPING
Follow the same oiling procedure if a replacement circulator is
installed into the system.
When the boiler is used in conjunction with a refrigeration system
it must be installed so that the chilled medium is piped in parallel
with the boiler with appropriate valves to prevent the chilled medium
from entering the boiler, fig. 4.
GAS CONNECTIONS
WARNING
THIS BOILER IS NOT INTENDED TO OPERATE AT GAS SUPPLY
PRESSURE OTHER THAN SHOWN ON THE RATING PLATE.
EXPOSURE TO HIGHER GAS SUPPLY PRESSURE MAY CAUSE
DAMAGE TO GAS VALVES WHICH CAN RESULT IN FIRE OR
EXPLOSION. IF OVERPRESSURE HAS OCCURRED SUCH AS
THROUGH IMPROPER TESTING OF GAS LINES OR EMERGENCY
MALFUNCTION OFTHE SUPPLYSYSTEM, THE GAS VALVES MUST
BE CHECKED FOR SAFE OPERATION. MAKE SURE THAT THE
OUTSIDE VENTS ON THE SUPPLY REGULATORS AND THE
SAFETY VENT VALVESARE PROTECTEDAGAINSTBLOCKAGE.
THESE ARE PARTS OF THE GAS SUPPLY SYSTEM, NOT THE
BOILER. VENT BLOCKAGE MAY OCCUR DURING ICE BUILD-UP
OR SNOW STORMS.
Water temperature in the heating system must be reduced to less
than 1000F (38°C) before cooling system is started, or damage to
the chiller unit may occur.
WHEN LOCAL CODES REQUIRE A MAIN MANUAL SHUTOFF
VALVE OUTSIDE THE BOILER JACKET,ASUITABLE MAIN MANUAL
SHUTOFF VALVE MUST BE INSTALLED IN A LOCATION
COMPLYING WITH THOSE CODES.
SCHEMATIC SHOWING PROPER PIPING ISOLATION
OF THE BOILER FROM THE CHILLER
FIGURE4
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ITIS IMPORTANTTO GUARDAGAINST GAS VALVE FOULING FROM
CONTAMINANTS IN THE GAS WAYS. SUCH FOULING MAYCAUSE
IMPROPER OPERATION, FIRE OR EXPLOSION.
2A.SIZING GAS SUPPLY LINE (For single boiler installations and
for installations of multiples of two or three of same size boilers).
Use table 6, or CAN/CSA B149.1-00 (latest recent edition) to size
IF COPPER SUPPLY LINES ARE USED THEY MUST BE iron pipe or equivalent gas supply line. Table 6 is based on a
CERTIFIED FOR GAS SERVICE.
pressure drop of 0.3 inches of water and a specific gravity of 0.60
approximately that of natural gas. (LP gas has an S.G. of about
1.53). If the service pressure is five inches water column or less,
use one pipe size larger than specified in table 6 in order to minimize
pressure drop in the line.
BEFORE ATTACHING THE GAS LINE BE SURE THAT ALL GAS
PIPE IS CLEAN ON THE INSIDE.
TO TRAPANY DIRTOR FOREIGN MATERIALIN THE GAS SUPPLY
LINE, A DIRT LEG (SOMETIMES CALLED DRIP LEG or sediment
trap) MUST BE INCORPORATED IN THE PIPING, SEE FIG. 1. The
dirt leg must be readily accessible and not subject to freezing
TABLE6
MAXIMUM CAPACITYOF PIPE IN CUBIC FEET OF GAS PER
HOUR (BASED UPONAPRESSURE DROP OF 0.3 INCH WATER
COLUMNAND 0.6 SPECIFIC GRAVITY GAS)
conditions.
INSTALL
IN
ACCORDANCE
WITH
RECOMMENDATIONS OF SERVING GAS SUPPLIERS. (Refer to
National Fuel Gas Code, ANSI Z223.1 and/or
CAN/CSA-B 149.1-00 Installation Codes.
Length
Meters
From Gas
(Nominal Iron Pipe Size (Inches)
1 1/4 1 1/2 2 1/2
Meter 1/2 3/4
1
2
3
4
To prevent damage, care must be taken not to apply too much
torque when attaching gas supply pipe to gas valve gas inlet.
3 (10) 132 278 520 1,050 1,600 3,050 4,800 8,500 17,500
6 (20)
9 (30)
92 190 350 730 1,100 2,100 3,300 5,900 12,000
73 152 285 590
890 1,650 2,700 4,700 9,700
760 1,450 2,300 4,100 8,300
670 1,270 2,000 3,600 7,400
610 1,150 1,850 3,250 6,800
560 1,050 1,700 3,000 6,200
530 990 1,600 2,800 5,800
490 930 1,500 2,600 5,400
460 870 1,400 2,500 5,100
410 780 1,250 2,200 4,500
380 710 1,130 2,000 4,100
350 650 1,050 1,850 3,800
12 (40) 63 130 245 500
15 (50) 56 115 215 440
18 ((60) 50 105 195 400
21 (70) 46 96 180 370
24 (80) 43 90 170 350
27 (90) 40 84 160 320
30 (100) 38 79 150 305
38 (125) 34 72 130 275
45 (150) 31 64 120 250
53 (175) 28 59 110 225
60 (200) 26 55 100 210
Fittings and unions in the gas line must be metal to metal type.
Apply joint compounds (pipe dope) sparingly and only to the male
threads of pipe joints. Do not apply compound to the first two
threads. Use compounds resistant to the action of liquefied
petroleum gases.
THE BOILER AND ITS GAS CONNECTIONS MUST BE LEAK
TESTED BEFORE PLACING THE BOILER IN OPERATION. Use
soap and water solution or other material acceptable for the
purpose in locating gas leaks. DO NOT USE MATCHES, CANDLES,
FLAME OR OTHER SOURCES OF IGNITION FOR THIS PURPOSE.
320 610
980 1,700 3,500
*The heating value of Natural Gas is approximately 1,050 Btu/Ft.3.
Propane (LP) Gas has a heating value of approximately 2,500 Btu/Ft3.
1 cu. meter=35.31 cu. feet.
DISCONNECT THE BOILER AND ITS MAIN MANUAL GAS
SHUTOFF VALVE FROM THE GAS SUPPLY PIPING SYSTEM
DURING ANY PRESSURE TESTING OF THE GAS SUPPLY
SYSTEM OVER 1/2 PSIG (3.5kPa).. THE GAS SUPPLY LINE MUST
BE CAPPED WHEN NOT CONNECTED TO THE BOILER.
Where it is necessary to use more than the average number of
pipe fittings i.e. elbows, tees, and valves in gas supply line, use a
pipe larger than specified to compensate for increased pressure
drop.
2B. SIZING GAS SUPPLY LINE (For multiples of over three boilers
of same size or for multiple installations of two or more mixed
sizes).
THE BOILER MUST BE ISOLATED FROM THE GAS SUPPLY
PIPING SYSTEM BY CLOSING ITS MAIN MANUAL GAS SHUTOFF
VALVE DURINGANY PRESSURE TESTING OF THE GAS SUPPLY
PIPING SYSTEM AT TEST PRESSURES EQUAL TO OR LESS
THAN 1/2 PSIG (3.5kPa).
Capacities in cubic feet per hour of 0.60 specific gravity gas for
different sizes and lengths are shown in table 6. No additional
allowance is necessary for an ordinary number of fittings.
PURGING
Applications of the gravity factor converts the figures given in table
6 to capacities with another gas of different specific gravity. Such
application is accomplished by multiplying the capacities given in
table 6 by the multipliers shown in table 7.
Gas line purging is required with new piping or systems in which
air has entered.
CAUTION
PURGING SHOULD BE PERFORMED BY PERSONS
EXPERIENCED IN THIS TYPE GAS SERVICE TOAVOID RISK OF
FIRE OR EXPLOSION. PURGE DISCHARGE MUST NOT ENTER
CONFINEDAREAS OR SPACES WHERE IGNITION CAN OCCUR.
THEAREAMUST BE WELLVENTILATED ANDALL SOURCES OF
IGNITION MUST BE INACTIVATED OR REMOVED.
To determine the size of each section of gas piping in a system
within the range of table 6 proceed as follows:
•
Determine the gas demand of each appliance to be attached
to the piping system. When table 6 is to be used to select the
piping size, calculate the gas demand in terms of cubic feet per
hour for each piping system outlet. The gas demand for an
appliance can be found by dividing its heat input rate by the
gas’s heating value.
1. CORRECT GAS
Make sure the gas on which the boiler will operate is the same as
that specified on the boiler rating plate. Do not install the boiler if
equipped for a different type gas — consult your supplier.
•
Obtain or determine the length of piping from the gas meter or
service regulator to the appliance(s).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
In table 6, select the row showing the distance to the most
remote outlet or the next longer distance if the table does not
give the exact length. This is the only distance used in
determining the size of any section of gas piping. If the gravity
factor is to be applied, the values in the selected row of table 6
are multiplied by the appropriate multiplier from table 7.
TABLE 7
MULTIPLIERS TO BE USED WITH TABLE 6 WHENAPPLYING
THE GRAVITY FACTOR TO OTHER THAN .60 SPECIFIC GRAVITY
Specific
Gravity
.35
Specific
Gravity
1.00
Multiplier
1.31
1.23
1.16
1.10
1.04
1.00
.96
Multiplier
.78
.40
.45
.50
.55
1.10
1.20
1.30
1.40
.74
.71
.68
.66
.63
.61
.59
.58
Total the gas demands of all appliances on the piping system.
Enter table 6, on the left hand side, at the row equal to or just
exceeding the distance to the most remote outlet. Select the
pipe size in the row with a capacity equal to or just exceeding
the total gas demand. This is the required main gas supply
line size leading away from the gas meter or regulator. To
determine the pipe size required for each branch outlet leading
away from the main supply line, determine the gas demand for
that outlet. Enter table 6 on the same row, and select the branch
pipe size for a capacity equal to or just exceeding the demand
at that outlet. The main line can be resized for a lesser capacity
after each branch outlet, since the gas demand is reduced.
Total the gas demands of all remaining appliances branching
off downstream on the main gas line. Re-enter table 6 in the
same row and select the appropriate pipe size with adequate
capacity. Repeat the branch sizing and main line re-sizing for
any remaining appliances in the system.
*.60 (Nat.)
.65
*1.50 (Prop.)
1.60
.70
.75
.80
.85
.93
.90
.87
.84
1.70
1.80
1.90
.56
.55
.54
*2.00 (Butane)
2.10
.90
.82
*Use these correction factors if exact specific gravity of the gas is not
known.
GAS PRESSURE REGULATORS
The gas pressure regulator is included in the combination gas
valve, fig. 6, and is set to operate on the gas specified on the boiler
model and rating plate.
Periodically check main burner, fig. 41, and pilot flame, fig. 42, for
proper operation. This should be checked every six months.
Do not subject the gas valve to inlet gas pressures of more than
14" W.C. (1/2 P.S.I.). If higher gas pressures are encountered, a
service regulator is necessary.
TABLE 8
CORRECT MANIFOLD PRESSURE FOR FULL
BOILER INPUT (IN INCHES OF WATER COLUMN)
Model
Number
Rated
Input
Manifold Pressure
Natural
3.5
Propane
10.0
HWB/HW-300
HWB/HW-399
HWB/HW-420
HWB/HW-520
HWB/HW-610
HW-670 Nat.
HW-670 Prop.
300,000
399,000
420,000
520,000
610,000
660,000
670,000
EXAMPLE
3.2
9.5
3.5
10.0
Job Condition:
3.5
10.0
3.5
10.0
Determining the required gas pipe size for a system composed of
two HWB/HW-420 boilers and two HWB/HW-610 boilers to be
installed as a multiple group, 50 lineal feet from meter. Gas to be
used has a .60 specific gravity and heating value of 1,000 Btu per
cubic foot.
3.5
10.0
Adjustment, if required, is performed as follows:
1. Set primary system temperature control dial (thermostat) at
lowest setting so that boiler will not call for heat.
Solution:
2. Attach a pressure gauge to the tapping in the control string
elbow.
2 HWB/HW-420 Boilers
2 HWB/HW-610 Boilers
=
=
840,000 Btuh
1,220,000 Btuh
3. Reset primary system temperature control dial (thermostat)
to highest setting. Main burner will now ignite.
Total Btuh Input
=
2,060,000 Btuh
Total Btuh Input
=
2,060,000 Btuh = 2,060 cf/h
1,000
4. With main burner firing, adjust pressure, if necessary, by turning
pressure regulator adjusting screw with a screwdriver.
Btu per Cubic Foot of Gas
•
•
Clockwise to increase pressure.
With a cubic foot per hour demand of 2,060 and with 50 lineal feet
of gas supply line, table 6 shows a pipe size of 3" (76mm) is
required.
Counterclockwise to decrease pressure.
5. Set primary system temperature control dial (thermostat) to
lowest setting.
NOTE: For other than .60 specific gravity, apply multiplier factor
as shown in table 7.
6. Remove pressure gauge and replace sealing plug.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Set primary system temperature control dial (thermostat) to Vent connectors serving appliances vented by natural draft shall
desired setting.
not be connected into any portion of mechanical draft systems
operating under positive pressure.
WARNING
The minimum distance from adjacent public walkways, adjacent
buildings, openable windows and building openings shall not be
less than those values specified in the National Fuel Gas Code,
ANSI Z223.1 and/or CAN/CSA B149.1-00, Installation Codes;
DO NOT INCREASE GAS PRESSURE ABOVE THAT SPECIFIED
ON THE RATING PLATE, AS OVERFIRING WILL RESULT IN
DAMAGE TO THE BOILER, AS WELL AS INCREASED RISK OF
FIRE, SOOTINGANDASPHYXIATION.
Stack or chimney must be a minimum height of 12" (305mm)
above the annual snow fall to prevent blockage.
If gas pressure regulator cannot be adjusted to correct pressure
with sufficient gas pressure at the valve, replace with new gas
valve.
Building materials must not come in contact with combustion
products from stack or chimney, due to the degradating properties
of flue products.
VENTING THE BOILER - STANDARD VENTING
WARNING
Flue products must have a minimum clearance of 4 feet (1.22m)
horizontally from, and in no case above or below, unless a 4-foot
(1.22m) horizontal distance is maintained, from electric meters,
gas meters, regulators and relief equipment.
THE INSTRUCTIONS IN THIS SECTION ON VENTING THE
BOILER MUST BE FOLLOWED TOAVOID CHOKED COMBUSTION
OR RECIRCULATION OF FLUE GASES. SUCH CONDITIONS
CAUSE SOOTING OR RISKS OF FIREANDASPHYXIATION.
The Canadian B149.1-00, Installation Code specifies a 6 foot
horizontal vent terminal clearance to gas and electric meters and
relief devices (this clearance is specified as 4 feet in the U.S.
under the National Fuel Gas Code, ANSI/Z223.1). Therefore
instruction provision 134.1-b19(d), which specifies compliance
with the 4 foot clearance, as applies in the U.S. only, and the
B149.1-00 Installation Code applies in Canada.
TYPE B VENTING MAY BE USED WITH THESE BOILERS. ALL
LOCAL UTILITY REGULATIONS ON VENTING SHOULD BE
FOLLOWED.
1. DRAFT HOOD
The draft hood furnished with this boiler must be installed without
alteration. Provision must be made if the boiler is installed in
confined space or a small boiler room to accommodate draft hood
spillage and avoid risks described above. The upper air opening
called for in the AIR REQUIREMENTS section of this manual is for
this purpose.
2. VENT CONNECTION
ROBERTSHAW® 7000 DERHC
HWB/HW-300, 399,-420, -520, -610, -670 NATURAL GAS WITH I.I.D.
HW-300, -399, -420, -520, -670 LP GAS WITH I.I.D. U.S. ONLY
Size and install proper size vent pipe. Do not reduce pipe size to
less than that of the draft hood outlet.
Horizontal runs of vent pipe shall be securely supported by
adequately placed (approximately every 4 feet or 1 meter),
noncombustible hangers and/or slip joints suitable for the weight
and design of the materials employed to prevent sagging and to
maintain a minimum upward slope of 1/4" (21mm/m) per foot
from the boiler to the vent terminals, fig. 7. Dampers or other
obstructions must not be installed in the vent. Be sure that the vent
pipe does not extend beyond the inside wall of the chimney.
ROBERTSHAW® 7000 ERHC (LP)
HWB/HW-300, 399,-420, -520, -610 SINGLE STAGE
STANDING PILOT, CANADIAN ONLY
FIGURE6
For boilers for connection to gas vents or chimneys, vent sizing,
installation and termination shall be in accordance with Part 7,
Venting of Equipment, of the National Fuel Gas Code, ANSI Z223.1,
or Section 7, Venting Systems and Air Supply for Appliances, of the
CAN/CSA B149.1-00, Installation Codes, or applicable provisions
of the local building codes.
VENT PIPE INSTALLATION
FIGURE7
® Robertshaw is a registered trademark of Fulton Controls Corp.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Where a continuous or intermittent back draft is found to exist the
cause must be determined and corrected. A special vent cap may
be required. If the back draft cannot be corrected by the normal
methods or if a suitable draft cannot be obtained, a blower type
flue gas exhauster may be employed to ensure proper venting and
correct combustion if permitted by local codes.
After it has been determined that each appliance remaining
connected to the common venting system properly vents when
tested as outlined above, return doors, windows, exhaust fans,
fireplace dampers and any other gas burning appliance to their
previous conditions of use.
Any improper operation of the common venting system should be
corrected so the installation conforms with the latest edition of
CAN/CGA B149.1-00 (latest edition). When resizing any portion of
the common venting system, the common venting system should
be resized to approach the minimum size as determined using
the appropriate tables in Appendix G in CAN/CSA B149.1-00.
WARNING
FAILURE TO CORRECT BACK DRAFTS WILL CAUSE AIR
CONTAMINATIONAND UNSAFE CONDITIONS.
Vent connectors serving appliances vented by natural draft shall
not be connected into any portion of mechanical draft systems
operating under positive pressure.
4. MULTIPLE VENTTABLE
Table 9 has been compiled to show the material sizes in a Type B
3. CONNECTING BOILER TO A COMMON VENT
doublewall
combined
vent
system.
Refer
to
CAN/CSA B149 .1-00 (latest edition), or the ASHRAE 1983
Equipment Volume for further information.
Do not connect the boiler to a common vent or chimney with solid
fuel burning equipment. This practice is prohibited by many local
building codes as is the practice of venting gas fired equipment to
the duct work of ventilation systems.
A combined vent system is one in which two or more boilers at one
level are attached to a common vent.
Where a separate vent connection is not available and the vent
pipe from the boiler must be connected to a common vent with oil
burning equipment, the vent pipe should enter the common vent
or chimney at a point ABOVE the flue pipe from the oil fired unit.
In order to use table 9, the connector rise and total vent height
must be known. Connector rise is vertical distance from the draft
hood outlet to the point where the manifold connection is made.
Total vent height is the least vertical distance from a draft hood
outlet to the top of the vent. Local codes or utility requirements
often govern termination height. ULC listed doublewall gas vents,
up through 24" (610mm) diameter, can be installed in heated and
unheated areas and can pass through floors, ceilings, partitions,
walls and roofs, provided the required one inch clearance is
observed. These vents should be installed in accordance with
CAN/CSA B149.1-00 (latest edition).
Where two or more appliances vent into a common vent connector
or manifold, the area of the common vent or vent connector should
at least equal the area of the largest vent connector plus 50% of
the areas of the additional draft hood outlets.
When removing a boiler from a system with a common vent, use
the following steps:
EXAMPLE SHOWING USE OF THE HWB/HW-610 COMBINED VENT
SIZING TABLE 9
Be sure the other appliances connected to the common vent are
not in operation.
Seal any unused openings in the common venting system.
Visually inspect the venting system for proper size and horizontal
pitch and determine there is no blockage or restriction, leakage,
corrosion and other deficiencies which could cause an unsafe
condition.
WARNING
Ensure sufficient supply and ventilation air. Under no circumstances
should the equipment room where the boiler is installed ever be
under negative pressure. Insufficient air supply can interfere with
combustion and ventilation of this boiler resulting in unsafe
conditions.
Insofar as is practical, close all building doors and windows and
all doors between the space in which the appliances remaining
connected to the common venting system are located and other
spaces of the building. Turn on clothes dryers and any appliance
not connected to the common venting system. Turn on any exhaust
fans, such as range hoods and bathroom exhausts, so they will
operate at maximum speed. Close fireplace dampers.
Place in operation the appliance being inspected. Follow the
lighting instructions. Adjust thermostat so appliance will operate
continuously.
Test for spillage at the draft hood relief opening after five minutes
of main burner operation. Use the flame of a match or candle.
FIGURE8
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE 9, COMBINED VENT SIZING TABLES
MODEL HW/HWB-300 BOILER
MODEL HW/HWB-610 BOILER
Input: 300,000 Btuh
Required Connector or Smoke Pipe Diameter
Connector Total Vent Height(Measured in Feet Above Draft Hood)
Draft Hood Outlet 8"
Input: 610,000 Btuh
Required Connector or Smoke Pipe Diameter
Connector Total Vent Height(Measured in Feet Above Draft Hood)
Draft Hood Outlet 12"
Rise in
Feet
10
15
20
30
40
50
60
80 100
Rise in
Feet
10
15
20
30
40
50
60
80 100
Connector Diameter (in Inches)
Connector Diameter (in Inches)
1
2
3
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
1
2
3
16
14
14
12
14
14
14
12
14
14
12
12
14
14
12
12
14
14
12
12
14
12
12
12
14
12
12
12
14
12
12
12
14
12
12
12
4 or more
Total
Input
Btuh x 1000
600
4 or more
Total
Number
if Units
Combined
Total Vent Height(Measured in Feet Above Draft Hood)
10 15 20 30 40 50 60 80 100
Manifold and Common Vent Diameter (in Inches)*
14
16
18
Number
if Units
Combined
Total Vent Height(Measured in Feet Above Draft Hood)
10 15 20 30 40 50 60 80 100
Manifold and Common Vent Diameter (in Inches)*
Input
Btuh x 1000
1220
1830
2440
3050
3660
4270
4880
5490
6100
6710
7320
2
3
4
12
14
16
12
14
16
12
14
14
10
12
14
10
12
14
10
12
14
10
12
12
10
12
12
2
3
4
5
6
7
8
9
18
22
26
28
32
34
36
38
40
42
44
18
20
24
26
28
32
34
36
38
38
42
16
20
22
26
28
30
32
34
36
38
38
16
18
20
24
26
28
30
30
32
34
36
14
18
20
22
24
26
28
30
30
32
34
14
16
18
22
24
24
26
28
30
30
32
14
16
18
20
22
24
26
28
28
28
32
14
16
18
20
22
22
24
26
26
28
30
14
14
16
18
20
22
24
24
26
26
28
900
1200
MODEL HW/HWB-399 BOILER
Input: 399,000 Btuh
Draft Hood Outlet 10"
Required Connector or Smoke Pipe Diameter
Connector Total Vent Height(Measured in Feet Above Draft Hood)
10
11
12
Rise in
Feet
10
15
20
30
40
50
60
80 100
Connector Diameter (in Inches)
1
2
3
12
12
12
10
12
12
10
10
12
12
10
10
12
10
10
10
12
10
10
10
12
10
10
10
12
10
10
10
12
10
10
10
12
10
10
10
4 or more
Total
Input
Btuh x 1000
798
Number
if Units
Total Vent Height(Measured in Feet Above Draft Hood)
10 15 20 30 40 50 60 80 100
Manifold and Common Vent Diameter (in Inches)*
14
18
20
MODEL HW/HWB-670 BOILER
Input: 660,000 or 670,000 Btuh
Required Connector or Smoke Pipe Diameter
Connector Total Vent Height(Measured in Feet Above Draft Hood)
Draft Hood Outlet 12"
Combined
2
3
4
14
16
20
14
16
18
12
14
16
12
14
16
12
14
16
12
14
14
12
14
14
12
12
14
1197
1596
Rise in
Feet
10
15
20
30
40
50
60
80 100
Connector Diameter (in Inches)
1
2
3
16
14
14
12
14
14
14
12
14
14
12
12
14
14
12
12
14
14
12
12
14
12
12
12
14
12
12
12
14
12
12
12
14
12
12
12
MODEL HW/HWB-420 BOILER
Input: 420,000 Btuh
Draft Hood Outlet 10"
Required Connector or Smoke Pipe Diameter
Connector Total Vent Height(Measured in Feet Above Draft Hood)
4 or more
Total
Number
if Units
Combined
Total Vent Height(Measured in Feet Above Draft Hood)
10 15 20 30 40 50 60 80 100
Manifold and Common Vent Diameter (in Inches)*
Input
Btuh x 1000
1340
2010
2680
3350
4020
4690
5360
6030
6700
7370
8040
Rise in
Feet
10
15
20
30
40
50
60
80 100
Connector Diameter (in Inches)
2
3
4
5
6
7
8
9
18
22
26
28
32
34
36
38
40
42
46
18
20
24
26
28
32
34
36
38
38
44
16
20
22
26
28
30
32
34
36
38
40
16
18
20
24
26
28
30
30
32
34
38
14
18
20
22
24
26
28
30
30
32
36
14
16
18
22
24
24
26
28
30
30
34
14
16
18
20
22
24
26
28
28
28
34
14
16
18
20
22
22
24
26
26
28
32
14
14
16
18
20
22
24
24
26
26
30
1
2
3
12
12
12
10
12
12
10
10
12
12
10
10
12
10
10
10
12
10
10
10
12
10
10
10
12
10
10
10
12
10
10
10
12
10
10
10
4 or more
Total
Input
Btuh x 1000
840
Number
if Units
Combined
Total Vent Height(Measured in Feet Above Draft Hood)
10 15 20 30 40 50 60 80 100
Manifold and Common Vent Diameter (in Inches)*
14
18
20
2
3
4
14
16
20
14
16
18
12
14
16
12
14
16
12
14
16
12
14
14
12
14
14
12
12
14
10
11
12
1260
1680
MODEL HW/HWB-520 BOILER
Input: 520,000 Btuh
Draft Hood Outlet 10"
Required Connector or Smoke Pipe Diameter
Connector Total Vent Height(Measured in Feet Above Draft Hood)
Known: (5) model HWB/HW-610 boilers. (See illustration).
Connector rise - 2' (Note 1' is minimum). Total vent height
30'.
Rise in
Feet
10
15
20
30
40
50
60
80 100
Connector Diameter (in Inches)
1
2
3
14
12
12
12
14
12
12
12
14
12
12
12
12
12
12
12
12
12
10
10
12
12
10
10
12
12
10
10
12
12
10
10
12
12
10
10
Problem:
Determine diameter of connector, manifold and
common vent.
4 or more
Total
Number
if Units
Combined
Total Vent Height(Measured in Feet Above Draft Hood)
10 15 20 30 40 50 60 80 100
Manifold and Common Vent Diameter (in Inches)*
16
20
22
26
28
30
32
Input
Btuh x 1000
1040
1560
2080
2600
3120
3640
4160
Procedure: Enter the top of the HWB/HW-610 table (total vent height)
at 30' and the side at 2' (connector rise). A 14" connector
diameter is indicated for each connector rise.
2
3
4
5
6
7
8
16
18
22
24
26
28
30
14
18
20
22
24
26
28
14
16
18
20
22
24
26
14
16
18
20
22
24
24
14
14
18
18
20
22
24
12
14
16
18
20
22
22
12
14
16
18
18
20
22
12
14
14
18
18
20
20
To determine the manifold and common vent size, enter this table
(total vent height) at 30 and the side at 5 boilers. A manifold
diameter of 24" (610mm) is indicated.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
gas vent properly by passing a lighted match or taper around
the edge of the relief opening of the draft hood. If the chimney or
gas vent is drawing properly, the match flame will be drawn into
the draft hood. If not, the combustion products will tend to
extinguish this flame. IF THE COMBUSTION PRODUCTS ARE
ESCAPING FROM THE RELIEF OPENING OF THE DRAFT
HOOD, DO NOT OPERATETHE EQUIPMENT UNTILPROPER
ADJUSTMENT OR REPAIRS ARE MADE TO PROVIDE
ADEQUATE DRAFT THROUGH THE CHIMNEY OR GAS VENT.”
VENTING MAINTENANCE - STANDARD VENTING
It is recommended that the heating surfaces and vent piping of
the appliance be checked every six months for dust, deterioration
and carbon deposits. Remove all soot or other obstructions from
chimney and flue which will retard free draft. Replace any
damaged or deteriorated parts of the venting system.
Qualified servicers should follow this procedure when the boiler’s
external heating surfaces and vent pipe need cleaning.
D. Next, turn on all other fuel burning appliances within the same
room so they will operate at their full input.
CAUTION
DO NOT USE A NYLON BRUSH OR OTHER STATIC CREATING
Repeat step C above, checking the draft on each appliance.
MATERIAL TO CLEAN DUST AND CARBON DEPOSITS FROM
HEATING SURFACESAND VENT.
SUCH DEPOSITS ARE FLAMMABLE AND MAY BE IGNITED BY
STATIC ELECTRICITY. USEAMETAL BRUSH TO MINIMIZE THE
DANGER OF EXPLOSION.
1. Turn off the electrical power (main manual gas shutoff and
pilot valves, if applicable).
FIGURE9
Allow boiler parts and vent to cool before disassembly.
2. Remove the boiler draft diverter and vent pipe running to the
chimney.
SAFETY RELIEF VALVES
Your local code authority may have other specific relief valve
requirements not covered below.
•
Check parts and chimney for obstructions and clean as
necessary.
3. Remove burner from boiler and other metal parts as required
to clean and vacuum the heat exchanger and combustion
coils.
WARNING
THE PURPOSE OF A SAFETY RELIEF VALVE IS TO AVOID
EXCESSIVE PRESSURE OR TEMPERATURE INTO THE STEAM
RANGE WHICH MAY CAUSE SCALDING AT FIXTURES, TANK
EXPLOSION, SYSTEM OR BOILER DAMAGE.
•
Refer to parts list supplied with this manual for
disassembly aid.
4. Reinstall the parts removed in steps 2 and 3.
TO AVOID SCALDING OR WATER DAMAGEA DRAIN LINE MUST
BE CONNECTED TO A RELIEF VALVE TO DIRECT DISCHARGE
TO A SAFE LOCATION. A DRAIN LINE MUST NOT BE REDUCED
FROM THE SIZE OF THE VALVE OUTLET AND IT MUST NOT
CONTAINANY VALVES BETWEEN THE BOILERAND THE RELIEF
•
Be sure the vent pipe has a minimum upward pitch of one
quarter inch per foot of length (21mm/m) and is sealed as
necessary.
5. Restore electrical power and gas supply to boiler.
•
Place boiler in operation by following the lighting VALVE OR THE RELIEF VALVEAND THE DRAIN EXIT. INADDITION,
instructions in this manual. THERE SHOULD NOT BE ANY RESTRICTIONS IN A DRAIN LINE
•
Check for gas leaks and proper boiler and vent operation. NOR SHOULD IT BE ROUTED THROUGH AREAS WHERE
FREEZING CONDITIONS MIGHT OCCUR. DO NOT THREAD OR
CAPTHE DRAIN LINE EXIT. RESTRICTING OR BLOCKINGADRAIN
LINE WILL DEFEAT THE PURPOSE OF THE RELIEF VALVE AND
MAY CREATE AN UNSAFE CONDITION. INSTALL A DRAIN LINE
WITHADOWNWARD SLOPE SUCH THAT IT NATURALLY DRAINS
ITSELF.
VENTING - SIDEWALL
(OPTIONAL) POWER VENT SYSTEM
If you are installing the optional Power Vent Kit, refer to your
HWB/HW Power Vent Kit Installation Instructions for proper wiring
and installation procedures. Contact your local A.O. Smith
representative for details.
If any safety relief valve is replaced, the replacement valve must
comply with the latest version of the ASME Boiler and Pressure
Vessel Code, Section IV or CSA B51, as applicable. Select a relief
valve with a discharge NOT less than the boiler input, and a pressure
rating NOT exceeding the working pressure of any component in
the system.
VENTING SYSTEM
HAVE VENTING SYSTEM CHECKED EVERY SIX MONTHS FOR
OBSTRUCTIONSAND/OR DETERIORATION IN VENT PIPING.
A. O. Smith supplies Canadian HW boilers for hot water supply
systems with a 125 psi pressure relief valve. This valve must be
installed in the water outlet as near to the boiler as possible.
A. Insofar as is practical, close all doors, windows and air inlets
to the building. Turn on all exhaust fans (range hood,
bathroom exhaust, etc.) so they will operate at their maximum
speed. Close fireplace dampers.
A. O. Smith United States HW and Canadian HWB boilers for space
heating are shipped with a 50 psi pressure relief valve. This valve
must be installed in the water outlet as near to the boiler as possible.
B. After allowing appliance to operate for five minutes, test for
spillage at the draft hood relief opening.
C. “CHECKING THE DRAFT. Operate vent connected gas An ASME rated temperature and pressure relief valve must be
utilization equipment for several minutes and check to see installed on each and every water storage tank in a hot water supply
that the combustion products are going up the chimney or system.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
The boiler, when installed, must be electrically bonded to ground
in accordance with the requirements of the authority having
jurisdiction or, in the absence of such requirements, with the
National Electrical Code, ANSI/NFPA 70 and/or the Canadian
Electrical Code Part 1, CSA C22.1, Electrical Code.
The storage tank temperature and pressure (T & P) relief valve
must comply with the applicable construction provisions of the
Standard for Relief Valves and Automatic Gas Shutoff Devices for
Hot Water Supply Systems, Z21.22 and/or CAN1-4.4. The T & P
valve must be of the automatic reset type and not embody a
single-use type fusible plug, cartridge or linkage.
STRICT ADHERENCE TO PIPING AND WIRING DIAGRAMS IS
REQUIRED TO PREVENT CONSTANT PUMP OPERATION WHEN
SYSTEM TEMPERATURE CONTROLIS SATISFIED. OTHERWISE
THE WARRANTY IS VOID AS STIPULATED IN THE LIMITED
WARRANTY ON THE INSTRUCTIONS MANUAL.
The T & P relief valve should have a maximum temperature rating
of 1000C (2100F), a pressure rating NOT exceeding the lowest
rated working pressure of any system component, and a discharge
capacity exceeding the total input of the water boilers supplying
water to the storage tank.
The electrical connections must be made so that the circulator will
operate before the gas valve opens. At no time may the controlling
system allow the burner to fire when there is no water flow through
the boilers.
Locate the T & P relief valve (a) in the top of the storage tank, or (b)
in the side of the tank on centerline within the upper 6 inches from
the top of the tank. See figures 20 to 31. Tapping shall be threaded
in accordance with the latest version of the Standard for Pipe
Threads, General Purpose (inch), ANSI/ASME B1.20.1
Refer to the diagrams in fig’s. 10 thru 11C for proper wiring
sequence with conventional single boiler installations.
Mark location with a Class lll label.
The THERMAL BALANCER shown is factory included by
A. O. Smith as part no. 98190. This device serves as a pump
shutdown delay switch to balance the rising boiler water
temperature to system temperature before the pump stops.
Overshooting of boiler temperature is prevented and stack loss
after shutdown is negligible.
See ANSI Z21.10.1, Part 1, MARKING, See CAN/CSA B149.1-00.
WIRING CONNECTIONS
CAUTION
LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN
SERVICING CONTROLS. WIRING ERRORS CAN CAUSE
IMPROPERAND DANGEROUS OPERATION.
WARNING
AN ELECTRICAL GROUND IS REQUIRED TO REDUCE RISK OF
ELECTRIC SHOCK OR POSSIBLE ELECTROCUTION. Make the
ground connection to the screw provided in the electrical supply
junction box on the boiler.
VERIFY PROPER OPERATIONAFTER SERVICING.
1. CONVENTIONALINSTALLATIONS
IF ANY OF THE ORIGINAL WIRE, AS SUPPLIED WITH THE
ALLELECTRICALWORK MUST BE INSTALLED INACCORDANCE APPLIANCE, MUST BE REPLACED, IT MUST BE REPLACED WITH
WITH NATIONALELECTRICALCODE,ANSI/NFPA70AND/ORTHE TYPE 1050C WIRE OR ITS EQUIVALENT, EXCEPTFOR THE FLAME
CANADIAN ELECTRICALCODE, PART1, CSAC22.1, ELECTRICAL SENSOR AND IGNITION CABLE WHICH ARE 2500C AND WIRES
CONNECTED TO THE COIL PROTECTOR WHICH ARE 2000C.
CODEAND MUST CONFORM TO LOCAL REGULATIONS.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SINGLE STAGE I.I.D. - ROBERTSHAW® GAS VALVE
HWB & HW-300, -399, -420, -520, -610 (NATURAL GAS ONLY) - CANADIAN MODELS
FIGURE 10
® Robertshaw is a registered trademark of Fulton Controls Corp.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SINGLE STAGE PROPANE - ROBERTSHAW GAS VALVE
24 VOLT -HW, HWB-420, -520, -610 CANADIAN MODELS
FIGURE11
18
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTION DIAGRAM HWB & HW 300, 399
(PROPANE GAS)
FIGURE 13
SINGLE STAGE PROPANE ROBERTSHAW GAS VALVE
24 VOLT - HWB, HW-300, 399 CANADIAN MODELS
FIGURE11A
19
Download from Www.Somanuals.com. All Manuals Search And Download.
HW-300, HW-399, HW-420, HW-500 & HW-670
(NATURALGAS)
SINGLE STAGE I.I.D. - ROBERTSHAW GAS VALVE
HW-300, -399, -420, -520 & 670 (NATURAL GAS ONLY) - U.S. MODELS
FIGURE11B
20
Download from Www.Somanuals.com. All Manuals Search And Download.
HW-300, HW-399, HW-420, HW-500 & HW-670
(PROPANE GAS)
FIGURE 12
SINGLE STAGE I.I.D. - ROBERTSHAW GAS VALVE
HW-300, -399, -420, -520 & 670 (PROPANE GAS ONLY) - U.S. MODELS
FIGURE11C
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TYPICAL WIRING DIAGRAM (IID NATURAL GAS) FOR SINGLE BOILERLINEAR-TEMP® INSTALLATION FOR CANADIAN MODELS
FIGURE 12
Space temperature controlling can be varied to meet the building
requirements. Either the single thermostat, as shown, or multiple
2. LINEAR-TEMP INSTALLATIONS
Control for these systems is decided mainly by the type of building zone thermostats should control a common relay. This relay
system controlling that is desired. A single boiler installation might
be controlled directly from space temperature thermostat(s).
Multiple boiler installations are more effective when the boilers
are sequenced in and out of operation by some form of main water
temperature controller. With one to three boilers, individual controls
set at progressive temperatures may be used. For more than
three or four boilers, a step controller is recommended.
controls electric power to the system primary circulator and to the
main water temperature controller. This provides for water
movement in the system before the main temperature controller
can start the secondary circulating pump or fire the boiler.
Figure 12 shows a typical wiring diagram for a single boiler space
heating installation. The boiler may be controlled by a main
temperature controller as shown or may include outdoor reset if
desired. The boiler shown is the model HW-610 with single stage
firing, typical of HW models.
Individual boiler controls, or the separate stages of a step controller,
should fire a boiler and also start the boiler loop circulator whenever
the first boiler of a group supplied by that boiler loop is fired. Some
large installations may require the firing of more than one boiler
per stage.
Figure 13 shows a layout for various choices of controls often
found in commercial heating. These layouts are not intended to
be wiring diagrams and only show the relation of one device to
another in the system.
The system or primary circulator may or may not be controlled by
the boiler sequencer. When this pump is operated through the
first switch of any type of step controller, care should be taken to
determine if a motor starter is needed due to insufficient switch
capacity.
Figure 13 is a typical layout of controls for two boilers with one
circulator and including optional outdoor reset and thermal
balancer. If a secondary circulator is used with each boiler,
arrangement for boiler no. 2 will be as shown for boiler no. 1.
If the primary pump is controlled by a manual switch or any other
controllers, the electric current supply to the boiler group should
be through the primary pump controller. The fast response of
A. O. Smith boilers eliminates any need to maintain boiler
temperature when the system is satisfied. Wiring should always
prevent firing of boiler(s) when there is no water flow in the mains.
Commercial size installations are always best when designed to
individual building requirements.
The layout in figure 13 is typical of many combination possibilities
to meet the requirements of different buildings. Brand names of
controls shown are suggestions and not directly related to any
particular type of system. THESE LAYOUTS ARE NOT WIRING
DIAGRAMS.
Installation diagrams show flow switches in the outlet piping from
each boiler as good protection against any boiler being fired when
the boiler loop circulator is not in operation. These flow switches
will also serve as protection if there is a loss of water.
A.O. Smith offers accessory Sequencing Control Panels;
TEK-252 for 2 Stage Boiler Control
Outdoor vent systems will normally require an automatic shutdown
control if there is a continuous recirculating main and/or if the
entire building is not under control of space temperature
thermostats. A single bulb outdoor sensing control will prevent
overheating of halls, stairways or other uncontrolled areas. There
are occasions when outdoor temperatures are temporarily too
warm for even a moderate amount of heating in these areas.
TEK-254 for 4 Stage Boiler Control
TEK-258 for 8 stage Boiler Control
For more information contact A.O. Smith Product Service
Department at 1-800-433-2545.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
3. Outdoor thermostat required if building controls do not provide automatic
shutdown of reset controls during warm weather.
Boilers and Secondary Circulator are Controlled by
• Dual Bulb, Dual Switch Controller
1. Building temperature controls supply electric power to building
circulator.
2. Main flow switch proves main water flow before energizing sequencing
and resetting controls.
Staging and Outdoor Reset of Main Water Temperature
CONTROLAPPLICATION DIAGRAM - TWO BOILER LINEAR-TEMP® INSTALLATION WITH TWO CIRCULATORS
FIGURE 13
NOTE:
Boilers and Secondary Circulator are Controlled by
1. Building temperature controls supply electric power to building
circulator.
• One Dual Bulb, Dual Switch Mechanical Controller and
• One Dual Bulb, single Switch Mechanical Controller
2. Main flow switch proves main water flow before energizing sequencing
and resetting controls.
3. Outdoor thermostat required if building controls do not provide automatic
shutdown of reset controls during warm weather.
Sequencing and Outdoor Reset of Main Water Temperature.
CONTROLAPPLICATION DIAGRAM - THREE BOILER LINEAR-TEMP® INSTALLATION WITH THREE CIRCULATORS
FIGURE 14
23
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
1. Building temperature controls supply electric
power to building circulator.
2. Main flow switch proves main water flow before
energizing sequencing and resetting controls.
3. Outdoor thermostat required if building controls
do not provide automatic shutdown of reset
controls during warm weather.
Boilers and Secondary
Circulator are Controlled by
Dual Bulb, Dual Switch Controller
Staging and Outdoor Reset of
Main Water Temperature
CONTROLAPPLICATION DIAGRAM - FOUR BOILER LINEAR-TEMP® INSTALLATION WITH TWO CIRCULATORS
FIGURE 15
NOTE:
1. Building temperature controls
supply electric power to
building circulator.
2. Main flow switch proves main
water flow before energizing
sequencing and resetting
controls.
3. Outdoor thermostat required if
building controls do not provide
automatic shutdown of reset
controls during warm weather.
4. Should motor load exceed 7.5
AMPS,
use relays or motor starters.
5. In absence of main flow switch
and low water cutoff, jumper
"A" and "B" together.
Boilers and Secondary Circulator areControlled by Dual Bulb, Dual Switch Controller Staging and Outdoor Reset of Main Water Temperature
CONTROLAPPLICATION DIAGRAM - EIGHT BOILER LINEAR-TEMP® INSTALLATION WITH INDIVIDUAL CIRCULATORS
FIGURE 16
24
Download from Www.Somanuals.com. All Manuals Search And Download.
CER-TEMP 80 - 1 UNIT INSTALLATION - FOR HOT WATER SUPPLY APPLICATION
CANADIAN MODELS, JUNCTION BOX W/6 TERMINALS
FIGURE 17
CER-TEMP 80 - 1 UNIT INSTALLATION - FOR HOT WATER SUPPLY APPLICATION
U.S. MODELS, JUCNTION BOX W/4 TERMINALS
FIGURE 18
FIGURE 19
25
Download from Www.Somanuals.com. All Manuals Search And Download.
CER-TEMP 80 - 2 OR 3 UNIT INSTALLATION - FOR HOT WATER SUPPLY APPLICATION
CANADIAN MODELS, JUNCTION BOX W/6 TERMINALS
FIGURE 20
26
Download from Www.Somanuals.com. All Manuals Search And Download.
SCHEMATIC
CANADIAN MODELS, JUNCTION BOX W/6 TERMINALS
27
Download from Www.Somanuals.com. All Manuals Search And Download.
CER-TEMP 80 - 2 OR 3 UNIT INSTALLATION CONNECTION DIAGRAM
(FOR HOT WATER SUPPLY APPLICATION)
U.S. MODELS, JUNCTION BOX W/4 TERMINALS
FIGURE 22
28
Download from Www.Somanuals.com. All Manuals Search And Download.
CER-TEMP 80 - 2 OR 3 UNIT INSTALLATION SCHEMATIC DIAGRAM
(FOR HOT WATER SUPPLY APPLICATION)
U.S. MODELS, JUNCTION BOX W/4 TERMINALS
FIGURE 23
29
Download from Www.Somanuals.com. All Manuals Search And Download.
BOOSTER - RECOVERY WIRING DIAGRAM
CANADIAN MODELS, JUNCTION BOX W/6 TERMINALS
FIGURE 24
SHURE-TEMP BOOSTER - RECOVERY WIRING DIAGRAM
(TWO TEMPERATURE SYSTEM)
CANADIAN MODELS, JUNCTION BOX W/6 TERMINALS
FIGURE 25
30
Download from Www.Somanuals.com. All Manuals Search And Download.
BOOSTER - RECOVERY WIRING DIAGRAM
U.S. MODELS, JUNCTION BOX W/4 TERMINALS
FIGURE 26
SHURE - TEMP BOOSTER - RECOVERY WIRING DIAGRAM
TWO-TEMPERATURE SYSTEM
U.S. MODELS, JUNCTION BOX W/4 TERMINALS
FIGURE 27
31
Download from Www.Somanuals.com. All Manuals Search And Download.
TANK TEMPERATURE CONTROL
WATER LINE CONNECTIONS
This section provides detailed installation diagrams for typical
methods of application for the unit using a Cer-Temp 80 Recovery
System (for one temperature water), and either Booster-Recovery
or the Shure-Temp Booster-Recovery System (for two temperature
water).
The water temperature in the storage tank is controlled by the Tank
Temperature Control. The sensing element is mounted inside
the hot water storage tank, see fig's. 31-38.
DANGER
HOT WATER TEMPERATURES REQUIRED FOR AUTOMATIC
DISHWASHER AND LAUNDRY USE CAN CAUSE SCALD BURNS
RESULTING IN SERIOUS PERSONAL INJURY AND/OR DEATH.
THE TEMPERATUREAT WHICH INJURY OCCURS VARIES WITH
THE PERSON’S AGE AND TIME OF EXPOSURE. THE SLOWER
RESPONSE TIME OF CHILDREN, AGED OR DISABLED
These diagrams will serve to provide the installer with a reference
for the materials and methods of piping necessary for installation.
It is essential that all water and gas piping, vent connections,
electrical wiring, and check and flow regulating valves be installed
as shown on the diagrams.
Consult the installation diagrams for appropriate locations to install PERSONS INCREASES THE HAZARDS TO THEM. NEVER ALLOW
the safety flow switch(es), drain valves, thermometers, relief valves
and the circulating pump(s). Apply suitable pipe thread sealing
compounds to only the male threads of parts to be connected.
If any of these parts are being replaced in a functioning system,
remember to shut off the manual gas and control valve(s) and
close off the water inlet(s). Open a nearby faucet to relieve pressure
and/or drain the boiler or system before attempting to install the
new parts.
SMALL CHILDREN TO USE A HOT WATER TAP, OR TO DRAW
THEIR OWN BATH WATER. NEVER LEAVEACHILD OR DISABLED
PERSON UNATTENDED IN A BATHTUB OR SHOWER.
Check the diagrams thoroughly before starting installation to avoid
errors and minimize time and materials cost.
If the system is to be filled with water for testing or other purposes
during cold weather and before actual operation, care must be
taken to prevent a downdraft entering the boiler or freezing air from
contacting the system. Failure to do so may cause the water in the
system to freeze with resulting damage to the system. Damage
due to freezing is not covered by the warranty.
The tank temperature control is adjustable from 100°F (37.7°C) to
220°F (104.4°C). It is recommended that lower water temperatures
be used to avoid the risk of scalding. It is further recommended, in
all cases, that the water temperature be set for the lowest
temperature which satisfies the user’s hot water needs. This will
also provide the most energy efficient operation of the water heater
and minimize scale formation.
This equipment must be protected against loss of water or loss of
water flow by the installation of a safety flow switch in the outlet
piping from the boiler. Piping and wiring diagrams show the
application of the accessory package for this purpose.
THE WATER HEATER SHOULD BE LOCATED INANAREAWHERE
THE GENERAL PUBLIC DOES NOT HAVE ACCESS TO SET
TEMPERATURES. SETTING THE WATER TEMPERATURE AT
120°F (49°C) WILL REDUCE THE RISK OF SCALDS. Some states
or provinces require settings at specific lower temperatures. Below
you will find listed the approximate time-to-burn relationship for
normal adult skin. Valves for reducing point-of-use temperature by
mixing cold and hot water are available. Also available are
inexpensive devices that attach to faucets to limit hot water
temperatures. Contact a licensed plumber or the local plumbing
authority.
HARD WATER
Where hard water conditions exist, water softening or the threshold
type of water treatment is recommended. This will protect the
dishwashers, coffee urns, water boilers, water piping and other
equipment. When water softening or water treatment is not
practical, a comparatively easy method of periodic lime removal
from the boiler may be employed by installing gate valves, drain
valve and acid fill opening as shown in CLEANING AND FLUSHING
section of this manual.
DETAIL OF TANK FITTING USED WITH MODIFIED RECOVERY
AND BOOSTER RECOVERY PIPING DIAGRAMS
FIGURE 28
32
Download from Www.Somanuals.com. All Manuals Search And Download.
A float type or an electronic probe type low water cutoff may be
used. The manufacturer's installation instructions must be followed.
Temperature
Setting
Time to Produce 2nd & 3rd
Degree Burns on Adult Skin
Nearly instantaneous
About 1/2 second
OVER: 170°F (77°C)
160°F (71°C)
150°F (65°C)
140°F (60°C)
130°F (54°C)
120°F (49°C)
THERMOMETERS
About 1-1/2 seconds
Less than 5 seconds
About 30 seconds
Thermometers should be obtained and field installed as shown in
the installation diagrams.
More than 5 minutes
Thermometers are installed in the system as a means of detecting
a possible liming condition in the boiler. An increase of 3°C (5°F)
USE ANTI-SCALD VALVE(S) in the hot water system to reduce the over the normal temperature rise through the boiler is an indication
risks of scalds at points of use such as lavatories, sinks and that lime is present. The term "temperature rise" designates the
bathing facilities.
difference between the boiler inlet and outlet water temperature.
A change in water temperature in the storage tank lower than the
Tank Temperature Control setting will cause the sensor to close
its contacts and consequently energize the boiler.
An increase of 3°C (5°F) above the recorded temperature rise may
signify a liming condition in the coils or heat exchanger. Refer to
CLEANING AND FLUSHING section of this manual for deliming
instructions.
If the Tank Temperature Control is out of calibration, replace it with
a new one; do not attempt to fix this control.
Record temperature rise at initial start-up for future reference.
WARNING
DRAIN VALVE (Not Supplied)
SHOULD OVERHEATING OCCUR OR THE GAS SUPPLY FAILTO
SHUT OFF, TURN OFF THE MANUAL GAS CONTROL VALVE TO
THE APPLIANCE.
A drain valve must be obtained and installed on each boiler and
tank for draining purposes, see installation diagrams in this
manual.
LOW WATER CUTOFF
CLOSED WATER SYSTEM
A low water cutoff is a safety device which is installed in the boiler
piping to prevent the boiler from firing in the event of inadequate
water levels in the boiler system.
This boiler should not be installed in a closed water system without
taking steps to reduce excessive system pressure due to thermal
expansion. Contact the water supplier or local plumbing inspector
on how to control this situation.
Where required by local code, this optional device is to be installed
in the boiler piping at a level above that of the heat exchanger.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
ONE HW-300, HW-399, HW-420, HW-520, HW-610 OR ONE HW-670 UP-FLOW MODEL
COMMERCIALBOILER WITH VERTICALTANK
DANGER
TEMPERATURE SETTING SHOULD NOT EXCEED SAFE USE
TEMPERATURE AT FIXTURES. SEE TANK TEMPERATURE
CONTROL WARNING ON PAGE 32. IF HIGHER PREHEAT
TEMPERATURES ARE NECESSARY TO OBTAIN ADEQUATE
BOOSTER OUTPUT, ADD AN ANTI-SCALD VALVE FOR HOT
WATER SUPPLIED TO FIXTURES.
IMPORTANT
THE INSTALLATION OF SAFETY FLOW SWITCH AS SHOWN
IS REQUIRED TO PROTECTTHE BOILER IN CASE OF WATER
SERVICE INTERRUPTION OR CIRCULATOR FAILURE (A.O.
SMITH PKG. NO. 211480).
+
PIPING AND FITTINGS BETWEEN GATE VALVES AND
BOILERS SHOULD BE BRASS OR BRONZE. OTHER
PIPING SHOULD CONFORM TO LOCAL CODES.
GATE VALVES ARE SHOWN FOR SERVICING BOILER.
HOWEVER, LOCAL CODES SHALL GOVERN THEIR USAGE.
*
PRESSURE RELIEF VALVE RATING SHOULD NOT
EXCEED PRESSURE CAPACITY OF ANY COMPONENT
IN THE SYSTEM.
WIRING - FIGURES 17, 18,
INSTALLINACCORDANCE
WITH ALL LOCAL CODES
** INSTALL THERMOMETER AND PRESSURE RELIEF IN
OPENINGS PROVIDED ON HW-520, HW-610 &
HW-670.
USE THIS TABLE FOR CORRECT
PUMPAND WATER PIPE SIZE
Minimum
Pipe Size
(Inches)
1-1/4"
1-1/2"
1-1/2"
B & G
Pump
Size
*Armstrong
Pump
Model
Number
HW-300
HW-399
HW-420
HW-520
HW-610/670
Size
125
S-25 1-1/4"
H-32 1-1/2"
H-32 1-1/2"
H-32 1-1/2"
S-35
1-1/2" HV
1-1/2" HV
1-1/2" HV
2"
1-1/2"
2"
*Assumes 50 equivalent feet pf piping or less.
FIGURE 29
34
Download from Www.Somanuals.com. All Manuals Search And Download.
ONE HW-300, HW-399, HW-420, HW-520, HW-610 OR ONE HW-670 UP-FLOW MODEL
COMMERCIALBOILER WITH HORIZONTALTANK
DANGER
TEMPERATURE SETTING SHOULD NOT EXCEED SAFE USE
TEMPERATURE AT FIXTURES. SEE TANK TEMPERATURE
CONTROL WARNING ON PAGE 32. IF HIGHER PREHEAT
TEMPERATURES ARE NECESSARY TO OBTAIN ADEQUATE
BOOSTER OUTPUT, ADD AN ANTI-SCALD VALVE FOR HOT
WATER SUPPLIED TO FIXTURES.
IMPORTANT
THE INSTALLATION OF SAFETY FLOW SWI
REQUIRED TO PROTECT THE BOILER IN
SERVICE INTERRUPTION OR CIRCULATO
(A.O. SMITH PKG. NO. 211480).
+
PIPING AND FITTINGS BETWEEN G
BOILERS SHOULD BE BRASS OR
PIPING SHOULD CONFORM TO LOCA
GATE VALVES ARE SHOWN FOR SER
HOWEVER, LOCAL CODES SHALL GOVER
*
PRESSURE RELIEF VALVE RATING SHO
PRESSURE CAPACITY OF ANY COM
SYSTEM.
** INSTALL THERMOMETER AND PRE
OPENINGS PROVIDED ON HW-520, H
WIRING - FIGURES 17, 18, 19
INSTALLINACCORDANCE
WITH ALL LOCAL CODES
USE THIS TABLE FOR CORRECT
PUMPAND WATER PIPE SIZE
Minimum
Pipe Size
(Inches)
1-1/4"
1-1/2"
1-1/2"
B & G
Pump
Size
*Armstrong
Pump
Model
Number
HW-300
HW-399
HW-420
HW-520
HW-610/670
Size
125
S-25 1-1/4"
H-32 1-1/2"
H-32 1-1/2"
H-32 1-1/2"
S-35
1-1/2" HV
1-1/2" HV
1-1/2" HV
2"
1-1/2"
2"
*Assumes 50 equivalent feet pf piping or less.
FIGURE 30
35
Download from Www.Somanuals.com. All Manuals Search And Download.
TWO HW-399's, HW-420's, HW-520's, HW-610's or HW-670's UP-FLOW MODEL
COMMERCIALBOILER WITH VERTICALTANK, CER-TEMP80
IMPORTANT
THE INSTALLATION OF SAFETY FLOW SWITCH AS SHOWN IS
REQUIRED TO PROTECT THE BOILER IN CASE OF WATER SERVICE
INTERRUPTION OR CIRCULATOR FAILURE
(A.O. SMITH PKG. NO. 211480).
+
PIPINGAND FITTINGS BETWEEN GATE VALVES AND BOILERS
SHOULD BE BRASS OR BRONZE. OTHER PIPING SHOULD
CONFORM TO LOCAL CODES.
CING BOILER. HOWEVER,
USAGE.
G SHOULD NOT EXCEED
PONENT IN THE SYSTEM.
PRESSURE RELIEF IN
HW-610 & HW-670.
DANGER
TEMPERATURE SETTING SHOULD NOT EXCEED SAFE USE TEMPERATURE AT
FIXTURES. SEE TANK TEMPERATURE CONTROL WARNING ON PAGE 32. IF
HIGHER PREHEAT TEMPERATURES ARE NECESSARY TO OBTAIN ADEQUATE
BOOSTER OUTPUT, ADD ANANTI-SCALD VALVE FOR HOT WATER SUPPLIED TO
FIXTURES.
WIRING - FIGURES 20, 21, 22, OR 23
HEATERS SPACED 30"APART
INSTALLINACCORDANCE
WITH ALL LOCAL CODES
USE THIS TABLE FOR CORRECT
PUMPAND WATER PIPE SIZE
MinimumPipe Size B & G
*Armstrong
Pump
Size
Model
Number
HW-300
HW-399
HW-420
HW-520
HW-610/670
(Inches)
Pump
Size
2"
2"
2"
A
2"
2"
B
1-1/2"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
S-35
S-35
S-35
S-35
2"
2"
2"
2-1/2"
2-1/2"
S-45 2-1/2"
*Assumes 50 equivalent feet pf piping or less.
FIGURE 31
36
Download from Www.Somanuals.com. All Manuals Search And Download.
TWO HW-300's, HW-399's, HW-420's, HW-520's, HW-610's OR HW-670's UP-FLOW MODEL
COMMERCIALBOILER WITH HORIZONTAL TANK
IMPORTANT
THE INSTALLATION OF SAFETY FLOW SWITCHAS SHOWN IS
REQUIRED TO PROTECT THE BOILER IN CASE OF WATER
SERVICE INTERRUPTION OR CIRCULATOR FAILURE
(A.O. SMITH PKG. NO.211480).
+
GAT
HOW
*
**
WIR
DANGER
TEMPERATURE SETTING SHOULD NOT EXCEED SAFE USE TEMPERATURE AT
FIXTURES. SEE TANK TEMPERATURE CONTROL WARNING ON PAGE 32. IF
HIGHER PREHEAT TEMPERATURES ARE NECESSARY TO OBTAIN ADEQUATE
BOOSTER OUTPUT, ADD ANANTI-SCALD VALVE FOR HOT WATER SUPPLIED TO
FIXTURES.
USE THIS TABLE FOR CORRECT
PUMPAND WATER PIPE SIZE
MinimumPipe Size B & G
*Armstrong
Pump
Size
Model
Number
HW-300
HW-399
HW-420
HW-520
HW-610/670
(Inches)
Pump
Size
2"
2"
2"
A
2"
2"
B
1-1/2"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
S-35
S-35
S-35
S-35
2"
2"
2"
2-1/2"
2-1/2"
S-45 2-1/2"
*Assumes 50 equivalent feet pf piping or less.
FIGURE 32
37
Download from Www.Somanuals.com. All Manuals Search And Download.
THREE HW-520's, HW-610's OR HW-670's UP-FLOW MODEL
COMMERCIALBOILER WITH VERTICALTANK, CER-TEMP80
WIRING - FIGURES 20, 21, 22 OR 23
INSTALLINACCORDANCE
WITH ALL LOCAL CODES
DANGER
TEMPERATURE SETTING SHOULD NOT EXCEED SAFE USE TEMPERATURE AT
FIXTURES. SEE TANK TEMPERATURE CONTROL WARNING ON PAGE 32. IF
HIGHER PREHEAT TEMPERATURES ARE NECESSARY TO OBTAIN ADEQUATE
BOOSTER OUTPUT, ADD ANANTI-SCALD VALVE FOR HOT WATER SUPPLIED TO
FIXTURES.
IMPORTANT
THE INSTALLATION OF SAFETY FLOW SWITCH AS SHOWN IS REQUIRED TO
PROTECT THE BOILER IN CASE OF WATER SERVICE INTERRUPTION OR
CIRCULATOR FAILURE
(A.O. SMITH PKG. NO. 211480).
+
PIPING AND FITTINGS BETWEEN GATE VALVES AND BOILERS SHOULD BE
BRASS OR BRONZE. OTHER PIPING SHOULD CONFORM TO LOCAL CODES.
GATE VALVESARE SHOWN FOR SERVICING BOILER. HOWEVER, LOCAL CODES
SHALL GOVERN THEIR USAGE.
*
PRESSURE RELIEF VALVE RATING SHOULD NOT EXCEED PRESSURE
CAPACITY OF ANY COMPONENT IN THE SYSTEM.
** INSTALLTHERMOMETER AND PRESSURE RELIEF IN OPENINGS PROVIDED
ON HW-520, HW-610 & HW-670.
USE THIS TABLE FOR CORRECT
PUMPAND WATER PIPE SIZE
MinimumPipe Size B & G
*Armstrong
Pump
Model
Number
(Inches)
Pump
Size
A
B
Size
HW-520
HW-610/670
2-1/2"
3"
1-1/2"
1-1/2"
2"
3" HD-3
S-45 2-1/2"
S-46
*Assumes 50 equivalent feet pf piping or less.
FIGURE 33
38
Download from Www.Somanuals.com. All Manuals Search And Download.
THREE HW-520's, HW-610's OR HW-670's UP-FLOW MODEL
COMMERCIALBOILER WITH HORIZONTALTANK, CER-TEMP80
DANGER
TEMPERATURE SETTING SHOULD NOT EXCEED SAFE USE TEMPERATURE AT
FIXTURES. SEE TANK TEMPERATURE CONTROL WARNING ON PAGE 32. IF
HIGHER PREHEAT TEMPERATURES ARE NECESSARY TO OBTAIN ADEQUATE
BOOSTER OUTPUT, ADD ANANTI-SCALD VALVE FOR HOT WATER SUPPLIED TO
FIXTURES.
IMPORTANT
THE INSTALLATION OF SAFETY FLOW SWITCH AS SHOWN IS REQUIRED TO
PROTECT THE BOILER IN CASE OF WATER SERVICE INTERRUPTION OR
CIRCULATOR FAILURE
(A.O. SMITH PKG. NO. 211480).
+
PIPING AND FITTINGS BETWEEN GATE VALVES AND BOILERS SHOULD BE
BRASS OR BRONZE. OTHER PIPING SHOULD CONFORM TO LOCAL CODES.
GATE VALVESARE SHOWN FOR SERVICING BOILER. HOWEVER, LOCAL CODES
SHALL GOVERN THEIR USAGE.
*
PRESSURE RELIEF VALVE RATING SHOULD NOT EXCEED PRESSURE
CAPACITY OF ANY COMPONENT IN THE SYSTEM.
** INSTALLTHERMOMETERAND PRESSURE RELIEF IN OPENINGS PROVIDED
ON HW-520, HW-610 & HW-670.
PUMPAND WATER PIPE SIZE
WIRING - FIGURES 20, 21, 22, OR 23
MinimumPipe Size B & G
*Armstrong
Pump
Model
Number
(Inches)
Pump
Size
HEATERS SPACED 24"APART
A
B
Size
HW-520
HW-610/670
2-1/2"
3"
1-1/2"
1-1/2"
2"
3" HD-3
S-45 2-1/2"
S-46
INSTALLINACCORDANCE
WITH ALL LOCAL CODES
*Assumes 50 equivalent feet pf piping or less.
FIGURE 34
39
Download from Www.Somanuals.com. All Manuals Search And Download.
BOOSTER RECOVERYSYSTEM (PATENTED)
TWO TEMPERATURE SYSTEM WITHOUT RECIRCULATION
ONE HW-300, HW-399, HW-420, HW-520, HW-610 OR HW-670 UP-FLOW MODEL
COMMERCIALBOILER WITH VERTICALTANK
DANGER
+
PIPING AND FITTINGS BETWEEN GATE VALVES AND BOILERS SHOULD BE
BRASS OR BRONZE. OTHER PIPING SHOULD CONFORM TO LOCAL CODES.
TEMPERATURE SETTING SHOULD NOT EXCEED SAFE USE TEMPERATURE AT
FIXTURES. SEE TANK TEMPERATURE CONTROL WARNING ON PAGE 32. IF
HIGHER PREHEAT TEMPERATURES ARE NECESSARY TO OBTAIN ADEQUATE
BOOSTER OUTPUT,ADD ANANTI-SCALD VALVE FOR HOT WATER SUPPLIED TO
FIXTURES.
GATE VALVESARE SHOWN FOR SERVICING BOILER. HOWEVER, LOCAL CODES
SHALL GOVERN THEIR USAGE.
*
PRESSURE RELIEF VALVE RATING SHOULD NOT EXCEED PRESSURE
CAPACITY OF ANY COMPONENT IN THE SYSTEM.
IMPORTANT
THE INSTALLATION OF SAFETY FLOW SWITCH AS SHOWN IS REQUIRED TO
PROTECT THE BOILER IN CASE OF WATER SERVICE INTERRUPTION OR
CIRCULATOR FAILURE (A.O. SMITH PKG. NO. 211480).
** INSTALLTHERMOMETERAND PRESSURE RELIEF IN OPENINGS PROVIDED
ON HW-520, HW-610 & HW-670.
WIRING - FIGURE 25 OR 27
INSTALLINACCORDANCE
WITH ALL LOCAL CODES
USE THIS TABLE FOR CORRECT
PUMPAND WATER PIPE SIZE
Minimum
Pipe Size
(Inches)
1-1/4"
1-1/2"
1-1/2"
B & G
Pump
Size
*Armstrong
Pump
Model
Number
HW-300
HW-399
HW-420
HW-520
HW-610/670
Size
125
S-25 1-1/4"
H-32 1-1/2"
H-32 1-1/2"
H-32 1-1/2"
S-35
1-1/2" HV
1-1/2" HV
1-1/2" HV
2"
1-1/2"
2"
*Assumes 50 equivalent feet pf piping or less.
FIGURE 35
40
Download from Www.Somanuals.com. All Manuals Search And Download.
BOOSTER RECOVERYSYSTEM (PATENTED)
TWO TEMPERATURE SYSTEM WITHOUT RECIRCULATION
ONE HW-300, HW-399, HW-420, HW-520, HW-610 OR HW-670 UP-FLOW MODEL
COMMERCIAL BOILER WITH HORIZONTALTANK
IMPORTANT
DANGER
THE INSTALLATION OF SAFETY FLOW SWITCH AS SHOWN IS REQUIRED TO
TEMPERATURE SETTING SHOULD NOT EXCEED SAFE USE TEMPERATURE AT
FIXTURES. SEE TANK TEMPERATURE CONTROL WARNING ON PAGE 32. IF
HIGHER PREHEAT TEMPERATURES ARE NECESSARY TO OBTAIN ADEQUATE
BOOSTER OUTPUT, ADD ANANTI-SCALD VALVE FOR HOT WATER SUPPLIED TO
FIXTURES.
PROTECT THE BOILER IN CASE OF WATER SERVICE INTERRUPTION OR
CIRCULATOR FAILURE (A.O. SMITH PKG. NO. 211480).
+
PIPING AND FITTINGS BETWEEN GATE VALVESAND BOILERS SHOULD BE
BRASS OR BRONZE. OTHER PIPING SHOULD CONFORM TO LOCAL CODES.
GATE VALVESARE SHOWN FOR SERVICING BOILER. HOWEVER, LOCALCODES
SHALL GOVERN THEIR USAGE.
SURE RELIEF VALVE RATING SHOULD NOT EXCEED PRESSURE
CITY OF ANY COMPONENT IN THE SYSTEM.
LL THERMOMETERAND PRESSURE RELIEF IN OPENINGS PROVIDED
W-520 & HW-610.
USE THIS TABLE FOR CORRECT
PUMPAND WATER PIPE SIZE
Minimum
Pipe Size
Number (Inches)
B & G
Pump
Size
*Armstrong
Pump
Model
Size
HW-300
HW-399
HW-420
HW-520
HW-610,670
1-1/4"
1-1/2"
1-1/2"
1-1/2"
2"
125
S-25 1-1/4"
H-32 1-1/2"
H-32 1-1/2"
H-32 1-1/2"
S-35
1-1/2" HV
1-1/2" HV
1-1/2" HV
2"
*Assumes 50 equivalent feet pf piping or less.
WIRING - FIGURE 25 OR 27
INSTALLINACCORDANCE
WITH ALL LOCAL CODES
PIPE SIZES "B"
CIRCULATING LOOP TO DISHWASHER
Type L Copper Tubing
Allowable
Pressure
Drop (PSI) 25"
(7.6m) (15m) (22.8m) (30m) (53m) (60m) (76m) (91m)
Distance from Heater to Dishwasher (Feet./Meters)
50"
75"
100" 175"
200" 250" 300"
10
20
30
40
50
1/2
1/2
1/2
1/2
1/2
3/4
1/2
1/2
1/2
1/2
3/4
1/2
1/2
1/2
1/2
3/4
3/4
1/2
1/2
1/2
3/4
3/4
3/4
1/2
1/2
3/4
3/4
3/4
3/4
3/4
1
1
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
FAIRLYROUGHPIPE
Allowable
Distance from Heater to Dishwasher (Feet./Meters)
Pressure
Drop (PSI) 25"
50" 75" 100" 175" 200" 250" 300"
(7.6m) (15m) (22.8m) (30m) (53m) (60m) (76m) (91m)
10
20
30
40
50
3/4
1/2
1/2
1/2
1/2
3/4
3/4
1/2
1/2
1/2
3/4
3/4
3/4
3/4
1/2
3/4
3/4
3/4
3/4
3/4
1
1
1
1
1
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
NOTE: Allowable pressure drop is the difference in PSI between supply
water pressure and the 20 PSI required at the dishwasher.
FIGURE 36
41
Download from Www.Somanuals.com. All Manuals Search And Download.
BOOSTER RECOVERY SYSTEM (PATENTED) - TWO TEMPERATURE SYSTEM WITHOUT RECIRCULATION
ONE HW-300, HW-399, HW-420, HW-520, HW-610 OR HW-670 UP-FLOW MODEL
COMMERCIAL BOILER WITH HORIZONTALTANK
+
PIPINGAND FITTINGS BETWEEN GATE VALVESAND BOILERS SHOULD BE
BRASS OR BRONZE. OTHER PIPING SHOULD CONFORM TO LOCAL CODES.
DANGER
TEMPERATURE SETTING SHOULD NOT EXCEED SAFE USE TEMPERATURE AT
FIXTURES. SEE TANK TEMPERATURE CONTROL WARNING ON PAGE 32. IF
HIGHER PREHEAT TEMPERATURES ARE NECESSARY TO OBTAIN ADEQUATE
BOOSTER OUTPUT, ADD ANANTI-SCALD VALVE FOR HOT WATER SUPPLIED TO
FIXTURES.
GATE VALVESARE SHOWN FOR SERVICING BOILER. HOWEVER, LOCAL CODES
SHALL GOVERN THEIR USAGE.
*
PRESSURE RELIEF VALVE RATING SHOULD NOT EXCEED PRESSURE
CAPACITY OF ANY COMPONENT IN THE SYSTEM.
IMPORTANT
THE INSTALLATION OF SAFETY FLOW SWITCH AS SHOWN IS REQUIRED TO
PROTECT THE BOILER IN CASE OF WATER SERVICE INTERRUPTION OR
CIRCULATOR FAILURE (A.O. SMITH PKG. NO. 211480).
** INSTALLTHERMOMETERAND PRESSURE RELIEF IN OPENINGS PROVIDED
ON HW-520, HW-610 & HW-670.
USE THIS TABLE FOR CORRECT
PUMPAND WATER PIPE SIZE
Minimum
Pipe Size
(Inches)
1-1/4"
1-1/2"
1-1/2"
B & G
Pump
Size
*Armstrong
Pump
Size
S-25 1-1/4"
Model
Number
HW-300
HW-399
HW-420
HW-520
HW-610/670
125
WIRING - FIGURE 24 OR 26
1-1/2" HV H-32 1-1/2"
1-1/2" HV H-32 1-1/2"
1-1/2" HV H-32 1-1/2"
INSTALLINACCORDANCE
WITH ALL LOCAL CODES
1-1/2"
2"
2"
S-35
*Assumes 50 equivalent feet pf piping or less.
FIGURE 37
42
Download from Www.Somanuals.com. All Manuals Search And Download.
BOOSTER RECOVERYSYSTEM (PATENTED)
TWO TEMPERATURE SYSTEM WITHOUT RECIRCULATION ONE HW-300, HW-399, HW-420, HW-520,HW-610 OR HW-670
UP-FLOW MODELCOMMERCIALBOILER WITH VERTICALTANK
DANGER
+
PIPING AND FITTINGS BETWEEN GATE VALVES AND BOILERS SHOULD BE
BRASS OR BRONZE. OTHER PIPING SHOULD CONFORM TO LOCAL CODES.
TEMPERATURE SETTING SHOULD NOT EXCEED SAFE USE TEMPERATURE AT
FIXTURES. SEE TANK TEMPERATURE CONTROL WARNING ON PAGE 32. IF
HIGHER PREHEAT TEMPERATURES ARE NECESSARY TO OBTAIN ADEQUATE
BOOSTER OUTPUT, ADD AN ANTI-SCALD VALVE FOR HOT WATER SUPPLIED TO
FIXTURES.
GATE VALVES ARE SHOWN FOR SERVICING BOILER. HOWEVER, LOCAL CODES
SHALL GOVERN THEIR USAGE.
*
PRESSURE RELIEF VALVE RATING SHOULD NOT EXCEED PRESSURE
CAPACITY OF ANY COMPONENT IN THE SYSTEM.
IMPORTANT
THE INSTALLATION OF SAFETY FLOW SWITCH AS SHOWN IS REQUIRED TO
PROTECT THE BOILER IN CASE OF WATER SERVICE INTERRUPTION OR
CIRCULATOR FAILURE (A.O. SMITH PKG. NO. 211480).
** INSTALLTHERMOMETERAND PRESSURE RELIEF IN OPENINGS PROVIDED
ON HW-520, HW-610 & HW-670.
FIGURE 38
INSTRUCTIONS FOR NUMBERED CONTROLS SHOWN ABOVE -
1
DUALTANK TEMPERATURE CONTROL
4
FLOW REGULATING PLUG COCK
(For Boiler Flow Rate Adjustment)
The dual tank temperature control should be installed in the
lower of the two 3/4" thermostat openings in the tank.
A slight closing of this valve may be necessary to set proper
water flow rate for 40°F temperature rise through the boiler.
Temperature rise is observed between the boiler inlet and
outlet thermometers.
Left Dial -High Limit
Adjust to 160°F with 20°F differential (minimum).
5 FLOW REGULATING PLUG COCK
(For Dishwasher Recirculating Loop)
Right Dial -Tank Temperature
Adjust to 140°F with 8°F differential (minimum).
Close this valve just enough to divert sufficient flow into
circulating loop that will maintain 180°F at end of loop adjacent
to dishwasher when dishwasher is not drawing water.
• May be adjusted slightly higher if total demand of
180°F water requires higher tank temperature.
2
LINE TEMPERATURE CONTROL
6
7
WATER PRESSURE REDUCING VALVE
Install as close to boiler as possible. Do not insulate piping or
tee immediately adjacent to the control.
Entering water pressure to the dishwasher must be set for 20
psig flow pressure. Excessive flow pressure may waste rinse
water beyond the capacity of the boiler to maintain it at 180°F
temperature.
Adjust dial to 185°F with 5°F differential (minimum).
INLET/OUTLET THERMOMETERS
• May be set slightly higher if radiant loss from piping prevents
maintaining 180°F at dishwasher.
See A. O. Smith deliming instructions Form 4778 when normal
temperature rise between rinse thermometers starts to
increase. Thermometers should be positioned near the inlet
and outlet of the heater.
3
BOILER LIMIT CONTROL
(Hi Limit adjust dial 220°F with 10°F differential)
43
Download from Www.Somanuals.com. All Manuals Search And Download.
WITH TWO VERTICAL TANKS
DANGER
TEMPERATURE SETTING SHOULD NOT
EXCEED SAFE USE TEMPERATURE AT
FIXTURES. SEE TANK TEMPERATURE
CONTROL WARNING ON PAGE 32. IF HIGHER
PREHEATTEMPERATURESARENECESSARYTO
OBTAIN ADEQUATE BOOSTER OUTPUT, ADD
AN ANTI-SCALD VALVE FOR HOT WATER
SUPPLIED TO FIXTURES.
WITH THREE VERTICAL TANKS
FIGURE 39
44
Download from Www.Somanuals.com. All Manuals Search And Download.
TWO HORIZONTALTANK INSTALLATION
THREE HORIZONTALTANK INSTALLATION
DANGER
TEMPERATURE SETTING SHOULD NOT EXCEED SAFE
USE TEMPERATURE AT FIXTURES. SEE TANK
TEMPERATURE CONTROL WARNING ON PAGE 32. IF
HIGHER PREHEAT TEMPERATURES ARE NECESSARY
TO OBTAIN ADEQUATE BOOSTER OUTPUT, ADD AN
ANTI-SCALD VALVE FOR HOT WATER SUPPLIED TO
FIXTURES.
FIGURE 40
START-UP AND OPERATING INSTRUCTIONS
4. Reset System Controller and High Limit Temperature Control
WARNING
to desired temperature. If unit fails to run, see Trouble-Shooting
in this manual.
After placing boiler into operation, the ignition system safety shutoff
device must be tested by the following test method.
Before operating the boiler, the entire system must be filled with
water, purged of air and checked for leaks. Do not use Stop Leak
or other boiler compounds. The gas piping should also be leak
tested.
1. Reset High Limit Temperature Control to lowest setting.
(See figure 38, page 44).
2. Reset System Controller to maximum setting, causing a call
for heat and allowing unit to run until High Limit Temperature
Control trips.
Any safety devices including low water cutoffs used in conjunction
with this boiler should receive periodic (every six months)
inspection to assure proper operation. A low water cutoff device of
the float type should be flushed every six months. All relief valves
should be inspected and manually operated at least twice a year.
3. Resetting the High Limit Temperature Control to a higher
setting, unit should run.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT
IT IS RECOMMENDED THAT A QUALIFIED PERSON PERFORM
THE INITIAL FIRING OF THE BOILER. AT THIS TIME THE USER
SHOULD NOT HESITATE TO ASK THE INDIVIDUAL ANY
QUESTIONS WHICH HE MAY HAVE IN REGARD TO THE
OPERATIONAND MAINTENANCE OF THE UNIT.
FILLING AND VENTING
1. Fast fill system through bypass until pressure approaches
desired system pressure. Close bypass valve and permit
pressure to be established by the pressure reducing valve.
FIGURE 41
The boiler should be periodically inspected by a qualified servicer
for continuous safe operation.
2. Vent all high points in system to purge system of air.
Qualified servicers should follow this procedure when the boiler’s
burners need cleaning.
If pressure bleeding of system is desired, install valves as shown
in fig. 1.
Where cast iron radiation and motorized valves are used,
conventional system pressure and installation practices should
be followed.
1. Turn off the electrical power and close the main manual
gas shutoff valve.
•
Allow boiler parts to cool before disassembly.
Provisions should be made to permit manual venting of radiators
or convectors.
2. Remove main burner manifold assembly from boiler.
•
Refer to parts list supplied with this manual for
disassembly aid.
PRECAUTIONS
If the unit is exposed to the following, do not operate boiler until all
corrective steps have been made by a qualified serviceman:
3. Remove any loose foreign material such as dust or lint
with a vacuum. Check all ports, orifices, and air openings
for blockage. Dislodge any foreign material causing
blockage. Remove any soot or carbon deposits with a rag
making sure to remove any lint left on burner by vacuuming
again.
1. Flooding to level of burner or controls or higher.
2. Exposure to fire.
3. If damaged.
4. Firing without water.
5. Sooting
4. Reinstall the burner manifold assembly on boiler.
5. Restore electrical power and gas supply to boiler.
CAUTION
SHOULD OVERHEATING OCCUR OR THE GAS SUPPLY FAILTO
SHUT OFF, DO NOT TURN OFF OR DISCONNECT THE
ELECTRICAL SUPPLYTO THE PUMP. INSTEAD, SHUTOFF THE
GAS SUPPLYATALOCATION EXTERNALTO THE APPLIANCE.
•
Put the boiler back in operation by following the lighting
instructions in this manual or on the lighting and
operating label on the boiler.
PILOT AND MAIN BURNER
•
Check for gas leaks and proper boiler and vent
operation.
To maintain safe operation and the greatest efficiency from the
boiler, check the pilot and the main burner once every six months
for proper flame characteristics.
2. PILOT BURNER - ELECTRONIC IGNITION
To establish pilot flame without main burner operation, it will
be necessary to perform the following steps:
1. MAIN BURNER
The main burner, fig. 41, should display the following
characteristics:
Servicing of the pilot burner (every six months) includes keeping
pilot shield (not shown) free of lint, cleaning the burner head,
the primary air opening and the orifice of the pilot burner,
fig. 42.
•
•
Provide complete combustion of gas.
Cause rapid ignition and carryover of flame across entire
burner.
1. Open fused disconnect switch or shut off electrical power
to the boiler.
•
•
Give reasonably quiet operation during ignition, burning
and extinction.
2. Turn the gas valve control knob counterclockwise to the
“PILOT” position.
Cause no excessive lifting of flame from burner ports.
3. Close fused disconnect switch to restore electrical power
to the boiler.
If the proceeding burner characteristics are not evident, check for
accumulation of lint or other foreign material that restricts or blocks
the air openings to the burner or boiler.
The pilot will now ignite provided the combination gas
valve knob is set at “PILOT” and the system is calling for
Also check for good flow of combustion and ventilating air to the
unit. Maintain a clear area around the boiler at all times.
heat.
(Continued on Page49)
46
Download from Www.Somanuals.com. All Manuals Search And Download.
LIGHTING AND OPERATING INSTRUCTIONS (NATURAL AND PROPANE GAS WITH I.I.D.)
FOR YOUR SAFETY READ BEFORE OPERATING
WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS
EXACTLY. A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY
DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
WHAT TO DO IFYOU SMELLGAS
WARNING:HOTWATERCANPRODUCE3rdDEGREE
BURNS IN 6 SECONDSAT 140° F. (60° C).
•
•
DO NOT TRY TO LIGHT ANY APPLIANCE.
DO NOT TOUCH ANY ELECTRIC SWITCH;
DO NOT USE ANY PHONE IN YOUR BUILDING.
IMMEDIATELY CALL YOUR GAS SUPPLIER FROM A
NEIGHBOR’S PHONE. FOLLOW THE GAS SUPPLIER’S
INSTRUCTIONS.
IN CASE OF POWER FAILURE DO NOT ATTEMPT TO
OPERATE APPLIANCE. IMPROPER INSTALLATION,
ADJUSTMENT,ALTERATION, SERVICE OR MAINTENANCE
CAN CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR
LOSS OF LIFE. REFER TO THE USER'S INFORMATION
MANUAL PROVIDED WITH THIS APPLIANCE.
INSTALLATIONAND SERVICE MUST BE PERFORMED BYA
QUALIFIED INSTALLER, SERVICE AGENCY OR THE GAS
SUPPLIER.
•
•
IF YOU CANNOT REACH YOUR GAS SUPPLIER, CALL
THE FIRE DEPARTMENT.
C. USE ONLY YOUR HAND TO PUSH IN OR TURN THE GAS
CONTROL KNOB. NEVER USE TOOLS. IF THE KNOB WILL
NOT PUSH IN OR TURN BY HAND, DON’T TRYTO REPAIR IT.
CALL A QUALIFIED SERVICE TECHNICIAN. FORCE OR
ATTEMPTED REPAIR MAY RESULT IN A FIRE OR
EXPLOSION.
D. DO NOT USE THISAPPLIANCE IFANY PART HAS BEEN UN-
DER WATER. IMMEDIATELY CALL A QUALIFIED
SERVICE TECHNICIAN TO INSPECT THE APPLIANCE AND
TO REPLACEANY PART OF THE CONTROL SYSTEM AND
ANY GAS CONTROLWHICH HAS BEEN UNDER WATER.
A. THIS APPLIANCE IS EQUIPPED WITH AN IGNITION DEVICE
WHICHAUTOMATICALLY LIGHTS THE PILOT. DO NOT TRY
TO LIGHT THE PILOT BY HAND.
B. BEFOREOPERATING:SMELLALLAROUNDTHEAPPLIANCE
AREA FOR GAS. BE SURE TO SMELL NEXT TO THE FLOOR
BECAUSE SOME GAS IS HEAVIER THAN AIR AND WILL
SETTLE ON THE FLOOR.
ROBERTSHAW® GAS CONTROL
® Registered trademark of Robertshaw-Fulton Controls Company
LIGHTING INSTRUCTIONS
7. TURN TOP KNOB OF GAS CONTROL COUNTER-
CLOCKWISE TO "ON" POSITION, (FIG. B). OPEN
FIRING AND PILOT MANUAL VALVES, COUNTER-
CLOCKWISE
8. TURN ON ALL ELECTRIC POWER TO THE APPLIANCE.
9. SET SYSTEM TEMPERATURE CONTROLLER TO DESIRED
SETTING.
10. WHEN CONTROLLER CALLS FOR HEAT, THE CIRCULAT
ING PUMPWILLOPERATEAND THE PILOT BURNER WILL
BESPARKIGNITED. GASCONTROLWILLOPENANDMAIN
BURNER WILL THEN IGNITE. NOTE: IF PILOT FAILS TO
IGNITE, TURN OFF APPLIANCE AND CONSULT YOUR
"INSTALLATION AND USERS MANUAL" FOR ADJUST
MENTS AND TROUBLESHOOTING.
1.
STOP! READ THE SAFETYINFORMATIONABOVE.
2. MAKE SURE BOILER AND SYSTEM ARE FILLED WITH
WATER AND ALL AIR HAS BEEN EXPELLED FROM
APPLIANCE.
3. TURN OFF ELECTRIC POWER TO THE APPLIANCE. SET
SYSTEM TEMPERATURE CONTROLLER TO LOWEST
SETTING. PURGE ALL GAS LINES OF AIR.
.
4. DO NOT ATTEMPT TO LIGHT THE PILOT BYHAND.
5. REFER TO DIAGRAMS ABOVE. TURN TOP KNOB OF
GAS CONTROL CLOCKWISE
(FIG. A). CLOSE FIRING AND PILOT MANUAL VALVES,
CLOCKWISE
TO "OFF" POSITION,
.
6. WAIT FIVE (5) MINUTES TO CLEAR OUTANY GAS. THEN
SMELL FOR GAS, INCLUDING NEAR THE FLOOR. IF YOU
SMELL GAS,
STOP! FOLLOW "B" IN THE SAFETY
11. IF THEAPPLIANCE WILL NOT OPERATE, FOLLOW THE
INSTRUCTIONS "TO TURN OFF GAS TO APPLIANCE" AND
CALL YOUR SERVICE TECHNICIAN OR GAS SUPPLIER.
INFORMATION ABOVE ON THIS LABEL. IF YOU DO NOT
SMELL GAS, GO THE NEXT STEP.
TO TURN OFF GAS TO APPLIANCE
A. SET THE SYSTEM CONTROLLER TO THE LOWEST
SETTING.
B. TURN OFF ELECTRICAL POWER TO APPLIANCE.
C. TURN TOP KNOB OF GAS CONTROL CLOCKWISE
"OFF" POSITION, (FIG. A). CLOSE FIRING AND PILOT
MANUAL VALVES, CLOCKWISE
TO
.
211686-000 Rev.00
47
Download from Www.Somanuals.com. All Manuals Search And Download.
LIGHTING AND OPERATING INSTRUCTIONS PROPANE (LP) STANDING PILOT MODELS
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS
EXACTLY. A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY
DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
WHAT TO DO IF YOU SMELL GAS
WARNING: HOT WATER CAN PRODUCE 3rd DEGREE
BURNS IN 6 SECONDS AT 140° F. (60° C).
•
•
DO NOT TRY TO LIGHT ANY APPLIANCE.
DO NOT TOUCH ANY ELECTRIC SWITCH; DO NOT USE
ANY PHONE IN YOUR BUILDING.
IN CASE OF POWER FAILURE DO NOT ATTEMPT TO OPERATE
APPLIANCE. IMPROPER INSTALLATION, ADJUSTMENT,
ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE
PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
REFER TO THE USER'S INFORMATION MANUAL PROVIDED WITH
THIS APPLIANCE. INSTALLATION AND SERVICE MUST BE
PERFORMED BY A QUALIFIED INSTALLER, SERVICE AGENCY
OR THE GAS SUPPLIER.
•
•
IMMEDIATELY CALL YOUR GAS SUPPLIER FROM A
NEIGHBOR’S PHONE. FOLLOW THE GAS SUPPLIER’S
INSTRUCTIONS.
IF YOU CANNOT REACH YOUR GAS SUPPLIER, CALL
THE FIRE DEPARTMENT.
C. USE ONLY YOUR HAND TO PUSH IN OR TURN THE GAS CONTROL
KNOB. NEVER USE TOOLS. IF THE KNOB WILL NOT PUSH IN OR
TURN BY HAND, DON’T TRY TO REPAIR IT. CALL A QUALIFIED
SERVICE TECHNICIAN. FORCE OR ATTEMPTED REPAIR MAY
RESULT IN A FIRE OR EXPLOSION.
A. THISAPPLIANCE IS EQUIPPED WITHA STANDING PILOT WHICH
MUST BE LIGHTED BY THE PUSH BUTTON IGNITER. WHEN
LIGHTING THE PILOT, FOLLOW THESE INSTRUCTIONS
EXACTLY.
D. DO NOT USE THIS APPLIANCE IF ANY PART HAS BEEN
B. BEFORE LIGHTING: SMELL ALL AROUND THE APPLIANCE AREA
FOR GAS. BE SURE TO SMELL NEXT TO THE FLOOR BECAUSE
SOME GAS IS HEAVIER THAN AIR AND WILL SETTLE ON THE
FLOOR.
UNDER WATER. IMMEDIATELY CALL
A
QUALIFIED
SERVICE TECHNICIAN TO INSPECT THE APPLIANCE AND TO
REPLACEANY PART OF THE CONTROL SYSTEM AND ANY GAS
CONTROLWHICH HAS BEEN UNDER WATER.
ROBERTSHAW® GAS CONTROL
® Registered trademark of Robertshaw-Fulton Controls Company
LIGHTING INSTRUCTIONS
1.
STOP! READ THE SAFETY INFORMATION ABOVE .
OR UNTIL PILOT WILL CONTINUE TO STAY LIT WHEN KNOB IS
RELEASED.
IF THE KNOB DOES NOT POP UP WHEN RELEASED, STOP AND
IMMEDIATELY CALL YOUR SERVICE TECHNICIAN OR GAS
SUPPLIER.
IF THE PILOT WILLNOT STAY LITAFTER SEVERAL TRIES, TURN
THE GAS CONTROL KNOB TO "OFF" AND CALL YOUR SERVICE
TECHNICIAN OR GAS SUPPLIER.
2. MAKE SURE BOILER AND SYSTEM ARE FILLED WITH WATER
AND ALL AIR HAS BEEN EXPELLED FROM APPLIANCE.
3. TURN OFF ELECTRIC POWER TO THE APPLIANCE. SET SYSTEM
TEMPERATURE CONTROLLER TO LOWEST SETTING. PURGE
ALL GAS LINES OF AIR.
•
•
4. REFER TO DIAGRAMS ABOVE. TURN TOP KNOB OF GAS
CONTROL CLOCKWISE
TO "OFF" POSITION, (FIG. A). CLOSE
11. OBSERVE PILOT THROUGH PEEP HOLE. ADJUST PILOT FLAME
TO HEIGHT OF APPROXIMATELY 3/8" TO 1/2" (9 TO 13mm) BY
MEANS OF PILOT GAS REGULATOR.
12. TURN TOP KNOB OF GAS CONTROL COUNTERCLOCKWISE TO
"ON" POSITION. (FIG. B)
FIRING AND PILOT MANUAL VALVES, CLOCKWISE
.
5. WAIT FIVE (5) MINUTES TO CLEAR OUT ANYGAS. THEN SMELL
FOR GAS, INCLUDING NEAR THE FLOOR. IF YOU SMELL GAS,
STOP! FOLLOW "B" IN THE SAFETYINFORMATIONABOVE
13. TURN ON ELECTRIC POWERAND SET SYSTEM TEMPERATURE
CONTROLLER TO DESIRED OPERATING TEMPERATURE. WHEN
CONTROLLER CALLS FOR HEAT, THE CIRCULATOR WILL
OPERATE. GAS VALVE
ON THIS LABEL.
GO TO THE NEXT STEP.
6. PILOT CAN BE VIEWED THROUGH THE PILOT PEEP HOLE. SEE
ILLUSTRATION 1.
7. OPEN FIRING AND PILOT MANUAL VALVES, COUNTER-
IF YOU DO NOT SMELL GAS,
WILL OPEN AND MAIN
BURNER WILL THEN
IGNITE.
CLOCKWISE
.
8. TURN TOP KNOB OF GAS CONTROL COUNTERCLOCKWISE
TO "PILOT" POSITION. (FIG. C)
14. IF THE APPLIANCE WILL
NOT OPERATE, FOLLOW
9. PUSH AND HOLD TOP KNOB DOWN, THIS ALLOWS GAS TO
FLOW TO PILOT.
THE INSTRUCTIONS "TO
TURN OFF GAS APPL-
10. DEPRESS PUSH BUTTON IGNITER, WHICH CAUSES SPARK TO
JUMP ACROSS ELECTRODE, IGNITING PILOT. CONTINUE TO
HOLD DOWN TOP KNOB FOR APPROXIMATELY 30 SECONDS
IANCE" AND CALL YOUR
SERVICE TECHNICIAN OR
GAS SUPPLIER.
ILLUSTRATION 1
TO TURN OFF GAS TO APPLIANCE
POSITION, (FIG. A). SEE ABOVE.
D. TURN FIRINGAND PILOT MANUAL VALVES CLOCKWISE
CLOSE POSITION.
A. SET THE SYSTEM CONTROLLER TO THE LOWEST SETTING.
B. TURN OFF ELECTRICAL POWER TO APPLIANCE.
TO
C. TURN TOP KNOB OF GAS CONTROL CLOCKWISE
TO "OFF"
211688-000 Rev.00
48
Download from Www.Somanuals.com. All Manuals Search And Download.
(Continued from Page 46)
4. Adjust pilot flame.
•
The pilot flame should envelop 3/8 to 1/2 inch of the tip of the
thermocouple. Remove pilot adjustment cover screw,
fig. 43b. Turn inner adjustment screw or pilot adjusting valve
clockwise to decrease, or counterclockwise to increase pilot
flame. Be sure to replace cover screw on combination gas
valve after adjustment to prevent possible gas leakage.
To adjust the pilot flame, remove the cap screw from the
pilot adjusting valve and turn to deliver a sufficient flame
at the pilot burner to cover 3/8" to 1/2" (10-12mm) of the
sensing probe tip. See fig. 42.
FIGURE 42
FIGURE 43B
If the pilot burner ignites but the main burner fails to light, check for
gas flow to the main burner.
2. Clogged pilot burner orifice.
•
Clean or replace orifice. A clogged orifice will restrict gas
flow and result in low thermocouple output.
Check for good terminal connection at the sensing probe at the
pilot burner assembly.
3. Incorrect orifice.
Check for electrical power to the valve. If electrical power and gas
are present at the valve and the valve does not open when system
calls for heat, replace valve.
•
Replace. Orifice size is stamped on the wrench flats.
4. Clogged primary air opening.
3. PILOT BURNER - NON-I.I.D. MODELS
•
Restricted air passages will soften the pilot flame and result
in poor thermocouple flame impingement.
Servicing of the pilot burner (every six months) includes keeping
pilot shield free of lint, cleaning the burner head, the primary air
opening and the orifice pilot burner, fig. 43a.
CLOSED CIRCUIT TEST
To ensure maximum millivolt output, the pilot burner flame should
envelop 3/8 to 1/2 inch of the thermocouple tip in fig. 43a. The
electrical output of the thermocouple will be affected by:
1. Attach the leads from a millivolt meter to the thermocouple and
junction block as shown in fig. 43c.
FIGURE 43C
• A satisfactory thermocouple will produce a reading of above
14 to 18 millivolts.
2. Transfer the lead on the junction block to other terminal,
figure 43d.
PIEZO PILOT IGNITOR
FIGURE 43A
• A satisfactory voltage supply through the protector switch
will result in a reading of 8 to 14 millivolts.
1. Low gas pressure
• If a reading of less than 8 millivolts is obtained, the junction
block connections and the protector switch leads must be
checked.
• Adjust pilot flame by means of the pilot gas adjustment
located in the gas valve.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
PROTECTOR SWITCH CONTINUITY TEST
Do not depress the protector switch reset button prior to testing.
The leads from the switch are removed from the thermocouple
function block and attached to the leads from a test flashlight.
The model N22T test kit (combination flashlight and continuity
tester) is manufactured by the RAY-O-Vac Company, Madison, WI
and available through local suppliers.
With the flashlight turned on, the lamp should light. If the lamp
lights, the protector switch circuit is closed and in proper working
order. If the lamp does not light, the reasons could be:
1. Protector switch contacts open.
FIGURE 43D
•
Depress reset button on switch (switch cannot be reset until
water temperature in the boiler coils drop below 200°F). Lamp
should light.
The purpose of checking the current ahead and after the protector
switch is to measure the millivolt drop across the contacts. This
drop should be between 4 and 6 millivolts.
2. Defective protector switch or bad leads.
FIGURE 44
50
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT
• If lamp does not light when reset button is depressed, attach
the test flashlight leads to the protector switch terminals. If
lamp does not light, switch is defective and must be replaced.
UNDER NO CIRCUMSTANCES SHOULD THE GAS INPUT
EXCEED THE INPUT SHOWN ON THE BOILER MODEL AND
RATING PLATE. OVERFIRING COULD RESULT IN DAMAGE OR
SOOTING OF THE BOILER. Minor variances from input on rating
plate can be corrected by adjustment of gas pressure regulators
described in GAS PRESSURE REGULATORS section of this
manual.
• If lamp does light, the leads are bad and must be repaired or
replaced.
CHECKING AND ADJUSTING THE INPUT
1. Follow steps 1 thru 6 of the OPERATING INSTRUCTIONS.
The inlet gas pressure must not exceed or be less than the values
shown on rating plate.
2. Attach a pressure gauge or a manometer to the manifold
pressure tapping and refer to table 8 for correct manifold
pressure.
CONTROL SETTINGS
MODEL HW-300, HW-399, HW-420, HW-520, HW-610 & HW-670
3. Follow steps 7 thru 11 of the OPERATING INSTRUCTIONS.
The high limit is a safety device wired in series with the ignition
system. Set the high limit control to approximately 100F above the
maximum designed system temperature. If the boiler outlet water
temperature should exceed the high limit setting, the main gas
valve will close but the circulator will continue to operate. Maximum
adjustable setting is 1150C (239°F) cut-out with a 30C (50F) to 250C
(450F) adjustable differential, fig. 45.
4. Use this formula to “clock” the meter. Be sure that other gas
consuming appliances are not ON during this interval.
3600 x H = Btuh
T
Btuh = The approximate actual input rate.
T =
Time in seconds to burn one cubic foot of gas.
H =
Heating value of the fuel gas in Btu per cubic foot of
gas.
EXAMPLE:
T = 9.0 seconds/ft3
H = 1050 Btu/ft3(natural gas)
Btuh = ?
FIGURE 45
Gas flow through meter:
ELECTRONIC INTERMITTENT PILOT
IGNITION CONTROL
3600 x 1050 = 420,000 Btuh
9.0
The solid state ignition control, fig. 46, ignites the pilot burner gas
by creating a spark at the pilot assembly. Pilot gas is ignited and
burns during each running cycle. The main burner and pilot gases
are cut off during the “OFF” cycle. Pilot gas ignition is proven by the
pilot sensor. Main burner ignition will not occur if the pilot sensor
does not first sense pilot ignition.
Small changes in the input rate may be made by adjusting the
manifold pressure, see GAS PRESSURE REGULATORS. Under
no circumstances should you exceed the maximum input rate for
the boiler given in table 2.
5. Repeat steps 1 thru 6 of the OPERATING INSTRUCTIONS.
On models with the igniter control a spark continues to operate for
15 seconds. If pilot ignition fails, there is a 5 minute wait and retry
or unit must be manually reset.
6. Remove the pressure gauge or manometer from the manifold
pressure tapping. Replace the screw-in plug in the manifold
pressure tap.
This control is non-adjustable and has no serviceable parts. The
removal of its cover voids the control warranty and may damage
the electronic circuit.
7. Repeat steps 7 thru 11 of the OPERATING INSTRUCTIONS.
The boiler will resume normal operation.
When the boiler is operating at full capacity, or full gas input, it
should consume 1 cu. ft. of gas in approximately the time
indicated in table 10.
TABLE 10
CONSUMPTION RATE
(Refer to Operating at Full Input or Full Capacity)
TIME TO CONSUME 1 CU. FT.
Heating
Value
OF GAS (SECONDS)
HWB/ HWB/ HWB/
Type
Gas
HWB/
HWB/
HWB/
Btu/Ft.^3 HW-300 HW-399 HW-420 HW-520 HW-610 HW-670
Natural
1050
12.6
9.5
9.0
7.3
6.2
5.7
Propane
2500
30.0
22.6
21.4
17.3
14.8
13.4
FIGURE 46
51
Download from Www.Somanuals.com. All Manuals Search And Download.
The input reduction is primarily achieved by reducing the size of
the main burner orifices. To do this, the main burner orifices require
replacement with orifices sized for the particular installation
elevation. When ordering, be sure to state the model number and
the altitude of the location where the boiler is being installed.
NORMAL OPERATING SEQUENCE WITH INTERMITTENT
IGNITION CONTROLS (I.I.D.)
1. System control calls for boiler operation.
2. Spark begins at pilot burner.
Upon field deration of the boiler, adjustment to the gas pressure
regulator is required. See CHECKING AND ADJUSTING THE
INPUT in this manual for inlet and manifold pressure requirements.
Also, due to the input rating reduction required at high altitudes,
the output rating of the appliance is also reduced and should be
compensated for in the sizing of the equipment for applications.
3. Pilot gas control valve is energized. Gas flows to pilot burner.
4. Pilot burner gas ignites. The sensing probe on the pilot burner
senses the presence of the pilot flame. The spark stops after
a few seconds.
NOTE: If the pilot gas isn’t present or doesn’t ignite after
15 seconds, the spark and pilot gas will stop, wait 5
minutes, and retry or unit must be manually reset..
THERMAL BALANCER
Figure 47 shows the internal wiring of the thermal balancer. The
device may be tested after disconnecting the four leads from their
respective terminals on the unit.
5. Main gas control valve is energized and main burner gas
ignites.
1. Apply a test light to the yellow and red leads.
NOTE: If gas interruption occurs during boiler operation, the
sensing probe will detect flame failure and within
.8 seconds de-energize the main and pilot burner gas
control valves. The operation of the control will revert
back to step 2 in the foregoing.
•
The lamp should light as the contact in this circuit is
normally closed when the resistor is cool.
2. Apply a light to the black and yellow leads.
•
The lamp should not light as the contact in this circuit is
normally open when the resistor is cool.
6. System control stops boiler operation. Main and pilot burners
are extinguished.
3. Remove the test light.
4. Apply 120 volts to the white and red leads which power the
1900 ohm resistor. After a warming period the contacts of the
thermal balancer should operate.
HIGHALTITUDE INSTALLATIONS
INCANADA
5. Remove the test light.
Acceptance of these models for use at altitudes above 2000 feet
(600 m) is based on field test of the individual installation by the
provincial/state authority having jurisdiction.
6. Apply the test light as described in steps 1 and 2.
While the resistor is still warm the lamp indications should be
the opposite as described previously.
IN THE U.S.A.
WARNING
INSTALLATIONS ABOVE 2000 FEET REQUIRE REPLACEMENT
OF THE BURNER ORIFICES IN ACCORDANCE WITH SECTION
8.1.2 OF THE NATIONALFUELGAS CODE (ANSI Z223.1). FAILURE
TO REPLACE THE ORIFICES WILL RESULT IN IMPROPER AND
INEFFICIENT OPERATION OF THE APPLIANCE RESULTING IN
THE PRODUCTION OF INCREASED LEVELS OF CARBON
MONOXIDE GAS IN EXCESS OF SAFE LIMITS WHICH COULD
RESULT IN SERIOUS PERSONAL INJURY OR DEATH.
FIGURE 47
COIL HIGH LIMIT CONTROL
(PROTECTOR SWITCH)
For specific orifice requirements, please refer to the appropriate
section of the National Fuel Gas Code ANSI Z223.1 or
CGA 2.17-M91.
This boiler is equipped with a manual reset protector switch, located
under the small cover on the side of the jacket, fig. 48. This device
provides positive shutdown of the heater in the event of boiler or
system malfunction. Should the surface temperature of the copper
tubing heat exchanger reach 120°C (250°F), the protector switch
will activate, the gas valve will close, the pilot and main burners will
be extinguished. If the protector switch should shut off unit, check
the following conditions:
You should contact your gas supplier for any specific changes
which may be required in your area.
Ratings specified by manufacturers for most boilers apply for
elevations up to 2000 feet (600 m). For elevations above 2000 feet
(600 m) ratings must be reduced by a rate of 4% for each 1000 feet
(300 m) above sea level.
•
•
•
•
No water in boiler.
Restricted water flow through the boiler.
Improper wiring (boiler firing without circulator operating).
Pump failure.
Example: If a boiler is rated at 610,000 Btu/hr. at sea level, to operate
the boiler at 5000 feet (1500 m) it must be derated by 20% (4% x 5)
to a new rating of 488,000 Btu/hr.
After correcting failure condition remove the protector switch cover
and push the reset button. The protector switch may be reset after
the coil surface temperature cools to .6°C (1°F).
A. O. Smith does build some models specifically for high altitude
service. Please check the rating plate before making changes.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
For proper performance mount the switch in a section of pipe
where there is a straight run of at least 5 pipe diameters on each
side of the flow switch (i.e. do not locate adjacent to valves, elbows,
orifices, etc.).
The flow switch shall be mounted in a standard 1-1/2" x 1-1/2" x 1"
tee for a 1-1/2" pipe application. For larger pipe sizes use a
reducing tee in order to keep the switch as close to the pipe as
possible. Install the flow switch in the branch (top) opening of the
reducing tee and provide adequate paddle length in the flow stream.
For example in a 2" pipe installation use a 2" x 2" x 1" reducing tee.
For 2", or 3" pipe use paddle segments as supplied. For other
pipe sizes (i.e. 1-1/4", 1-1/2" and 2-1/2") trim the paddle to the
proper pipe size, see fig. 49. If a standard tee is used, install a face
or hex bushing in the top opening. The paddle must be adjusted
or trimmed to the size of the pipe in which it will be installed.
PROTECTOR SWITCH
FIGURE 48
PRESSURE REDUCING VALVE
The screen in the pressure reducing valve may require occasional
cleaning due to foreign material in the water supply. This will
restrict the flow and could reduce the effectiveness of purging and
prolong filling time. To inspect the screen, close the main water
supply valve ahead of the pressure reducing valve and remove the
screen for cleaning, see fig’s. 1 and 2.
CAUTION
Any part of the paddle must not touch the pipe or any restrictions in
the pipe. Screw the flow switch in position so the flat of the paddle
is at right angles to the flow. The arrow on the side case must point
in the direction of the flow.
TABLE 11 - SAFETYFLOW SWITCH
SAFETY FLOW SWITCH
The safety flow switch is a safety device which must be installed at
the water outlet of the unit to prevent main burner operation in the
event of inadequate water flow through the unit, see fig’s. 10 through
12 and 17 through 27.
Minimum Pipe Rate
Contacts Closed
(Flow)
Contacts Open
(No Flow)
Model
Number
GPM
5.8
7.5
7.5
13.7
13.7
LPS
0.36
0.47
0.47
0.86
0.86
GPM
3.7
LPS
HWB/HW-300
HWB/HW-399
HWB/HW-420
HWB/HW-520
HWB/HW-610/670
0.23
0.31
0.31
0.60
0.60
5.0
An accessory package A. O. Smith No. 211480 containing a safety
flow switch is available for this application.
5.0
9.5
9.5
This switch may be mounted in a horizontal pipe line or a vertical
pipe line with upward water flow. Do not install the switch where
the water flow is downward.
The safety flow switch may be field adjusted to obtain higher
minimum flow rates than those shown in table 11.
CAUTION
Paddle must be trimmed at the dotted arc. It must not touch
the pipe or have any restriction when installed
FIGURE 49
53
Download from Www.Somanuals.com. All Manuals Search And Download.
To adjust the flow rate setting:
Thermal expansion is the normal response of water when it is
heated. In a closed system, thermal expansion will cause the
system pressure to build until the relief valve actuation pressure is
equaled. Then, the relief valve will open, allowing some water to
1. Remove the flow switch cover.
2. For higher flow rate—turn the range adjusting screw clockwise. escape, slightly lowering the pressure.
A properly sized expansion tank should be installed.
3. For lower flow rate—turn the range adjusting screw
counter-clockwise.
ABOVE ALL, DO NOT PLUG ANY RELIEF VALVE. THIS IS NOTA
SOLUTIONAND CAN CREATE AHAZARDOUS SITUATION.
CAUTION
The switch is factory set at approximately the minimum flow rate,
see Table II. It must not be set lower than the factory setting as this
may result in the switch failing to return at a “no flow” condition.
REPLACEMENT PARTS
U.S. Models
Replacement parts may be ordered through A. O. Smith dealers,
authorized servicers or distributors. Refer to the Yellow Pages for
where to call or contact the A. O. Smith Water Products Company,
5621 W. 115th Street, Alsip, IL 60803, 1-800-433-2545. When
ordering parts be sure to state the quantity, part number and
description of the item including the complete model and serial
number as it appears on the product. Refer to the parts lists for
more information.
4. Replace the flow switch cover.
Where units are installed in multiples, each boiler must be
individually protected by a safety flow switch.
SAFETYRELIEF VALVE MAINTENANCE
Every six months the system safety relief valves should be checked
to ensure that they are in operating condition. To check a relief
valve, lift the lever at the end of the valve several times. The valve
Canadian Models
should seat properly and operate freely.
Replacement parts may be ordered through A. O. Smith dealers,
authorized servicers or distributors. Refer to the Yellow Pages for
where to call or contact the A. O. Smith Enterprises, Ltd., P. O. Box
310, 768 Erie St., Stratford, Ontario N5A 6T3, 1-800-265-8520.
When ordering parts be sure to state the quantity, part number and
description of the item including the complete model and serial
number as it appears on the product. Refer to the parts lists for
more information.
CAUTION
BEFORE MANUALLY OPERATINGARELIEF VALVE, MAKE SURE
THAT A DRAIN LINE HAS BEEN ATTACHED TO THE VALVE TO
DIRECT THE DISCHARGE TO AN OPEN DRAIN. FAILURE TO
TAKE THIS PRECAUTION COULD MEAN CONTACT WITH
EXTREMELY HOT WATER EXITING THE VALVE DURING THIS
CHECK OPERATION.
If a relief valve discharges periodically or continuously, it may be
due to thermal expansion of water in a closed water supply system,
or, it may be due to thermal expansion of water in a closed water
supply system, or, it may be due to a faulty relief valve.
QUALITY REPLACEMENT PARTS
REMOVAL OF EXISTING BOILER FROM A COMMON VENTING SYSTEM
Place in operation the appliance being inspected. Follow the
lighting instructions. Adjust thermostat so appliance will operate
continuously.
At the time of removal of an existing boiler, the following steps shall
be followed with each appliance remaining connected to the
common venting system placed in operation, while the other
appliances remaining connected to the common venting system
are not in operation.
Test for spillage at the draft hood relief opening after 5 minutes of
main burner operation. Use the flame of a match or candle, or
smoke from a cigarette, cigar or pipe.
Seal any unused openings in the common venting system.
After it has been determined that each appliance remaining
connected to the common venting system properly vents when
tested as outlined above, return doors, windows, exhaust fans,
fireplace dampers and any other gas-burning appliance to their
previous condition of use.
Visually inspect the venting system for proper size and horizontal
pitch and determine there is no blockage or restriction, leakage,
corrosion and other deficiencies which could cause an unsafe
condition.
Insofar as is practical, close all building doors and windows and
all doors between the space in which the appliances remaining
connected to the common venting system are located and other
spaces of the building. Turn on clothes dryers and any appliance
not connected to the common venting system. Turn on any exhaust
fans, such as range hoods and bathroom exhausts, so they will
operate at maximum speed. Do not operate a summer exhaust
fan. Close fireplace dampers.
Any improper operation of the common venting system should be
corrected so the installation conforms with the National Fuel Gas
Code, ANSI Z223.1 and/or CAN/CGA B149, Installation Codes.
When resizing any portion of the common venting system, the
common venting system should be resized to approach the
minimum size as determined using the appropriate tables in
Appendix F in the National Fuel Gas Code, ANSI Z223.1 and/or
CAN/CGA B149 Installation Codes.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL MAINTENANCE
More frequent inspections may be necessary depending on water
conditions.
These boilers are designed to give many years of efficient and
satisfactory service when properly operated and maintained. To
assure continued good performance, the following
recommendations are made.
The boiler mounted gas and electrical controls have been designed
to give both dependable service and long life. However, malfunction
can occur, as with any piece of equipment. It is therefore
recommended that all components be checked periodically by a
qualified serviceman for proper operation.
The area around the unit should be kept clean and free from lint
and debris. Sweeping the floor around the boiler should be done
carefully. This will reduce the dust and dirt which may enter the
burner and pilot air passages, causing improper combustion and
sooting.
RELIEF VALVE
The safety relief valve should be opened at least twice a year to
check its working condition. This will aid in assuring proper
pressure relief protection. Lift the lever at the top of the valve several
times until the valve seats properly and operate freely.
THE FLOW OF COMBUSTION AND VENTILATION AIR TO THE
BOILER MUST NOT BE OBSTRUCTED.
THE BOILER AREA MUST BE KEPT CLEAR AND FREE FROM
COMBUSTIBLE MATERIALS, GASOLINE, AND OTHER
FLAMMABLE VAPORSAND LIQUIDS.
DANGER
THE WATER PASSING OUT OF THE VALVE DURING CHECKING
OPERATION MAY BE EXTREMELY HOT. BEFORE OPERATING
RELIEF VALVE MAKE SURE DRAIN LINE IS INSTALLED TO
DIRECT DISCHARGE TOASAFE LOCATION SUCHASAN OPEN
DRAIN, TOAVOID SCALDING OR WATER DAMAGE.
Any safety devices including low water cutoffs used in conjunction
with this boiler should receive periodic (every six months)
inspection to assure proper operation. A low water cutoff device of
the float type should be flushed every six months. All relief valves
should be inspected and manually operated at least twice a year.
More frequent inspections may be necessary depending on water
conditions.
WARNING
SHOULD OVERHEATING OCCUR OR THE GAS SUPPLY FAILTO
SHUT OFF, TURN THE MANUAL GAS CONTROL VALVE TO THE
APPLIANCE.
Periodic checks, at least twice a year, should be made for water
and/or gas leaks.
CLEANING AND FLUSHING INSTRUCTIONS
INTERNALCONTAMINANTS
HOT WATER SUPPLY BOILERS
PREVENTIVE MAINTENANCE
The hydronic system must be internally cleaned and flushed after
a new or replacement boiler has been installed to remove
contaminants that may have accumulated during installation. This
is doubly important when a replacement boiler is installed into an
existing system where Stop Leak or other boiler additives have
been used.
Some solids exist in most water supply systems. As the water is
heated, these tend to drop out depositing as scale or lime. This
scale is comparatively easy to remove if cleaned before the unit
becomes clogged. The time between cleaning will vary depending
upon water conditions and usage. A change of about 50F (3°C) in
the normal temperature rise through the unit is usually an indication
that it is time for preventive maintenance.
Failure to clean and flush the system can produce acid
concentrations that become corrosive, cause gases to form that
block water circulation or lead to formation of deposits on the boiler
surfaces, any of which could result in damage to the system and
circulator.
Figure 31 shows typical piping arrangement for gravity deliming of
lime deposits.
DELIMING
All hot water heating systems should be completely flushed with a
grease removing solution to assure trouble-tree operation. Pipe
joint compounds, soldering paste, grease on tubing and pipe all
tend to contaminate a system.
The amount of calcium carbonate (lime) released from water is in
direct proportion to water temperature and usage, see fig. 49. The
higher the water temperature or water usage, the more lime
deposits are dropped out of the water. This is the lime scale which
forms in pipes, boilers and on cooking utensils.
Failure to flush contaminates from a system can cause solids to
form on the inside of boiler exchangers, create excessive amounts
of air and other gases to block circulation, foul various system
accessories and even deteriorate circulation seals and impellers.
Lime accumulation not only reduces the life of the equipment but
also reduces efficiency of the boiler and increases fuel
consumption.
It is recommended that after installation, the boiler and system
when filled should include the proper percentage of cleaning
solution related to approximate water volume of the system. Fire
and circulate for about one hour and then flush clean with fresh
water. Commercial grease removing solutions are available from
your distributor.
The usage of water softening equipment greatly reduces the
hardness of water. However, this equipment does not always
remove all of the hardness (lime). For this reason it is
recommended that a regular schedule for deliming be maintained.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
The time between cleaning will vary from two to six months 9. When foaming action has stopped completely, allow 10 to
depending upon water conditions and usage. A change of
approximately 50F in the normal temperature rise through the boiler
is usually an indication that scale should be removed. For long
15 minutes for the solvent to dissolve any remaining scale in
the unit.
life, copper or brass is recommended for all valves, pipe and fittings 10. Open the drain cock and drain all the solvent from unit.
used between gate valves “A” and “B” and the boiler, see fig. 51.
11. Remove standpipe and drain hose assembly from tees. Install
Boiler failure due to excessive lime build-up voids the warranty.
fittings originally removed into openings. Open valve “A”
allowing fresh water to flow through unit and out drain cock for
three to five minutes.
12. Close drain cock and open valve “B”. Restore electric and
gas supply.
Check unit for proper operation.
FIGURE 50
DELIMING THE HWB/HW BOILER
FIGURE 51
DELIMING SOLVENTS
MINIMUM AMOUNT OF CLEANING
A. O. Smith recommends the use of generic commercially available
cleaning solutions to remove lime buildup from your system.
SOLUTION REQUIRED
Model
Number
Litres
12
19
19
26
Gallons
HWB/HW-300
HWB/HW-399
HWB/HW-420
HWB/HW-520
HWB/HW-610/670
3
5
5
7
7
CAUTION
Read the instructions on the label of the deliming solvent container.
26
REMOVING LIGHT DEPOSITS OF SCALE
1. Shut off electric and gas supply to the unit.
2. Close gate valves “A” and “B”, see fig.51.
3. Open drain cock and drain unit.
HEAVY LIME DEPOSITS
If the solvent does not readily pass through the clogged coils or
heat exchanger, it will be necessary to use an acid pump deliming
kit, or contact a service agency for proper cleaning.
A. O. Smith part no. 4930 motorized deliming pump kit, complete
with pump, hoses, fittings, container and instructions is available
from your dealer, distributor or the A. O. Smith Water Products
Company.
4. Remove pressure relief valve from outlet header assembly
and install drain hose assembly, see fig. 51.
5. Install standpipe in tee of inlet line, see fig. 51.
6. Close drain cock.
REMOVING SILICATE
Ammonium bifluoride flakes (NH4F HF) can be used in conjunction
7. Slowly pour required amount of deliming solvent shown below with delimer to delime and remove siliceous materials from copper
into unit through standpipe. Direct solution into suitable coil water boilers.
container with hose, see illustration.
Ammonium bifluoride flakes should be purchased locally from
8. Continue to fill until foaming action stops.
chemical suppliers.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
—
Gas supply pressure is within the maximum and minimum operating
ranges listed on the appliance rating plate/label.
PRE-TROUBLESHOOTING
Before any extensive trouble-shooting, perform the following:
Ensure That:
—
—
Voltage (24 vac) is supplied by transformer.
Appliance is wired according to wiring diagram.
—
—
Voltage (120 vac) is supplied to the appliance.
Note: Cross wiring the 24 volt circuit of the relay will short the transformer.
System control (tank temperature control, thermostat, etc.) is calling
for appliance operation (call for heat).
—
All wire terminals/connectors are firmly attached to valves, modules,
switches, limit controls, etc.
—
Other contacts (switches) are closed (relay, low water cutoff, flow
switch, coil protector, pressure switch, etc.).
—
For LP models only check for possible lockout condition of the ignition
module.
TROUBLESHOOTING
CER-TEMP 80 RECOVERY SYSTEM CHECKOUT PROCEDURE
Use this checkout for Cer-Temp 80 Recovery Systems. (For hot water supply application only)
SYSTEM OPERATION
Checkout Sequence
Contact
Incorrect
Cause
Remedy
Set tank temperature
control (thermostat)
20°F (10°C) below
Circulating pump
and burner shut
off.
Pump and burner Tank temperature control
Replace.
remain on.
(thermostat) defective.
tank water temperature
With thermal
System wiring is incorrect.
Correct wiring.
balancer, pump off
delay of approx-
imately 2 minutes.
Circulating pump Pump wired for continuous Correct wiring.
on.
operation.
Burner on.
Gas valve stuck or defective. Correct or replace valve.
System wiring is incorrect.
Correct wiring.
Set tank temperature
control (thermostat)
20°F (10°C) above
Circulating pump
and burner on.
Circulating pump High limit control set too
on. low.
Replace. (If problem
proven to be at this
control by applying
tank water temperature.
High limit control differential jumper to terminals.)
too wide.
System wiring is incorrect.
Correct wiring.
Coil protector switch has
activated.
Remove control cover,
depress reset button.
Gas valve or wiring
defective.
Check wiring. Repair or
replace valve.
Circulating pump Power off or system
Check power supply
and wiring.
and burner off.
wiring is incorrect.
Tank temperature control
(thermostat) defective.
Replace.
Burner on.
System wiring is incorrect.
Correct wiring.
Replace.
Boiler outlet
temperature exceeds
210°F (100°C).
Circulating pump
on.
Circulating pump High limit control defective,
and burner on.
or set too high (max. should
be set at 200°F).
Set tank temperature
control (thermostat)
for desired water
temperature.
System maintains.
desired water
temperature.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
CHECKING HONEYWELL S-8600H OR S-8610M
INTERMITTENT IGNITION CONTROLS
NO SPARK AT PILOT BURNER
Turn off gas supply.
NO
Is voltage (24 Vac) across the 24 V terminals
on module during “Call for heat”?
Replace ignition module.
YES
Is voltage (24 Vac) across the PV & MV/PV terminals on
“call for heat”?
YES
NO
NOTE: S8610M will automatically reset every 5 minutes.
S8600H pilot valve will be de-energized if module goes into
lockout condition. Reset system by turning electrical power off or
by turning system controller to off or down below "call for heat".
Wait one minute, then turn system on.
YES
Turn on gas supply.
turn on power supply.
Turn off power supply.
Is ignition cable firmly plugged into pilot
assembly and module?
NO
NO
Securely connect cable
and/or ground wire.
Is ground wire firmly attached to pilot assembly and GND
terminal on module?
YES
Replace pilot burner
and/or ground wire.
Are ignition cable and ground wire in good condition
(not brittle, burnt or cracked)?
YES
Ensure ground strap is the closest metal to the igniter/sensor
rod (electrode) to prevent the spark from shorting out to other
metal parts (pilot screen, pilot shield, etc.).
NO
NO
Carefully bend downward
top of ground strap
to achieve 1/8”
Ignition cable must not touch metal surfaces or current
carrying wires.
spark gap.
Is there a 1/8” gap between ground strap and electrode?
YES
Is the ceramic insulator surrounding the electrode
cracked or broken?
Replace Ignition
Module.
YES
Replace pilot burner assembly.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
CHECKING HONEYWELL S8600H OR S-8610M
INTERMITTENT IGNITION CONTROLS
SPARK AT PILOT BURNER BUT PILOT WILL NOT LIGHT
Ensure all manual shutoff valves are fully open; All filters are
clean; All gas connections are gas tight; Pilot tubing is not
damaged, obstructed or kinked; and pilot orifice is unclogged.
Check for air in gas line, purge (bleed) line if necessary.
YES
NO
NO
Are the wires securely attached to the pilot operator on the gas
control and to the PV & MV/PV terminals on the ignition module?
Attach wires firmly.
YES
Install a pressure gauge in the pilot tubing line between the gas
control and the pilot burner assembly. Ensure that the pilot
adjustment screw (under cap) is adjusted to a position that will
permit gas to flow.
Replace gas valve.
Is pilot gas flowing during ignition attempt?
YES
Turn on power supply
Turn off power supply.
YES
Is ignition cable firmly plugged into pilot assembly and
module?
NO
Securely connect
cable and/or ground
wire.
Is ground wire firmly attached to pilot assembly and GND
terminal on module?
YES
NO
Replace pilot burner
and/or ground wire.
Are ignition cable and ground wire in good condition (not brittle, burnt, or cracked)?
YES
Ensure ground strap is the closest metal to the igniter/sensor
rod (electrode) to prevent the spark from shorting out to
other metal parts (pilot screen, pilot shield, etc.).
Carefully bend down-
wards top of ground
strap to achieve
NO
Ignition cable must not touch metal surfaces or current
carrying wires.
1/8” spark gap.
Is there a 1/8” gap between ground strap and electrode?
YES
NO
Is ceramic insulator surrounding the electrode in good
Replace pilot burner.
condition (not cracked or broken)?
YES
NO
Replace Ignition
Module.
Is there excessive draft conditions that may cause pilot
burner ignition problems?
YES
Correct draft problems in a manner that would ensure
adequate combustion and ventilation air and proper
pilot burner performance.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
CHECKING HONEYWELL S-8600H OR S8610M
INTERMITTENT IGNITION CONTROLS
PILOT BURNER LIGHTS BUT MAIN BURNER DOES NOT LIGHT
Correct the situation by consulting the
installation or user’s manual on how to
adjust pilot flame.
NO
NO
Does the pilot flame cover 3/8” to 1/2”
of ingniter/sensor rod?
YES
Replace
ignition
module.
NO
Does spark stay on for more than
15 seconds after the pilot is “proven” (lit)?
Is voltage (24 Vac) across terminals
MV & MV/PV?
YES
Are the wires securely attached to the main
valve operator on the gas control and to
terminals MV & MV/PV on ignition module?
Attach
wires
firmly.
NO
YES
YES
Replace main gas valve.
Ensure the ground wire and ignition cable are
separate from each other (prevents shorting
out).
NO
Replace pilot burner
and/or ground wire.
Are they in good condition (not brittle, burnt or
cracked)?
YES
NO
NO
Is the ceramic insulator surrounding the
igniter/sensor rod in good condition
(not broken or cracked)?
Replace pilot burner.
YES
Is the igniter/sensor rod in good
condition (not worn, corroded, sooted
or damaged)?
Clean rod or replace
pilot burner if necessary.
YES
Replace ignition module.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
CHECKING HONEYWELL S8600H OR S-8610M
INTERMITTENT IGNITION CONTROLS
NO SPARK AT PILOT BURNER BUT PILOT WILL NOT LIGHT
Turn off gas supply.
Fix connection and/or
NO
Is there a good connection between terminals?
tighten module to the
appliance
Is module securely attached to appliance for good ground
connection?
YES
NO
NO
Check the circuit providing
24 VAC.
Is voltage (24VAC across transformer positive terminal and
GND with "call for heat"??
YES
Is voltage (24VAC) across ignition module terminals 24 Volt and
GND on "call for heater"?
Replace ignition module.
NOTE: (For LP models only) Pilot Valve will be de-energized if
module goes into lockout condition. Reset system by turning
electrical power off or by turning system controller down below
"call for heat". Wait one minute then turn system on.
Turn on gas supply and/
or power supply.
YES
Turn off power supply.
NO
NO
Securely connect cable
and/or ground wire.
Is high voltage cable assembly firmly plugged into module?
Is pilot ground wire firmly attached to the pilot assembly and
GND terminal on module?
YES
Replace pilot burner
and/or ground wire.
Are high voltage cable and ground wire in good condition (not
brittle, burnt or cracked)?
YES
Make sure pilot flame spreader (hood) is the closest metal to
the electrode to prevent the spark from shorting out to other
metal parts (pilot screen, pilot shield, etc).
Carefully bend down-
wards top of ground
strap to achieve
NO
NO
High voltage cable must not touch metal surfaces or current
carrying wires.
1/8” spark gap.
Is there a 7/64" spark gap between the tip (edge) of the hood
and electrode, and is the gap located in the pilot gas stream?
YES
Is the ceramic insulator surrounding the electrode in good
condition (not cracked or broken)?
Replace Ignition Module.
YES
Replace Pilot Burner Assembly
61
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
A. O. Smith Corporation, the warrantor, extends the following LIMITED WARRANTY to the owner of this hydronic boiler.
1. If within TEN years after initial installation of the boiler, a heat exchanger, coil or gas burner shall prove upon examination by the warrantor to be
defective in material or workmanship, the warrantor, at his option will exchange or repair such part or portion. This term is reduced to FIVE years
if this boiler is used for water heating purposes other than hydronic space heating.
a. This warranty is extended to the owner for all other parts or portion during the FIRST year following initial installation of this boiler.
b. The warranty on the repair or replacement of the part or portion will be limited to the unexpired term of the original warranty.
3. CONDITIONS AND EXCEPTIONS
This warranty shall apply only when the boiler is installed in accordance with local plumbing and building codes, ordinances and regulations, the
printed instructions provided with it and good industry practices. In addition, an appropriately sized safety relief valve certified to the ASME Boiler
and Pressure Vessel Code must have been installed and fresh, clean water used for filling and make-up purposes.
a. This warranty shall apply only when the boiler is:
(1) used at temperatures not exceeding the maximum setting of its operative and/or high limit control;
(2) used at water pressure not exceeding the working pressure shown on the boiler;
(3) used when filled with potable water, free to circulate at all times and with the heat exchanger(s) and coil(s) free of damaging scale
deposits;
(4) in a non-corrosive and non-contaminated atmosphere;
(5) owned by the original purchaser;
(6) in it's original installation location;
(7) is sized in accordance with proper sizing techniques for commercial boilers;
(8) bearing a rating plate which has not been altered, defaced or removed except as required by the warrantor;
(9) fired at the factory rated input using the fuel stated on the rating plate;
(10) maintained in accordance with the instructions printed in the manual included with the boiler;
(11) in the United States, its territories or possessions, and Canada;
(12) with an intermittent circulating action and with the pump and burner operating together.
(13) in an indoor installation only.
b. Any accident to the boiler, any misuse, abuse (including freezing) or alteration of it, any operation of it in a modified form, or any attempt to repair
leaks in the coil or heat exchanger will void this warranty.
4. SERVICEAND REPAIR EXPENSE
Under this limited warranty the warrantor will provide only a replacement part. The owner is responsible for all other costs. Such costs may include
but are not limited to:
a. Labor charges for service, removal, repair or reinstallation of the component part;
b. Shipping, delivery, handling, and administrative charges for forwarding the replacement part from the nearest distributor and returning the
claimed defective part to such distributor.
c. All cost necessary or incidental for any materials and/or permits required for installation of the replacement.
5. LIMITATION ON IMPLIED WARRANTIES
Implied warranties, including any warranty of merchantability imposed on the sale of this boiler under state law are limited to one (1) year duration
for the boiler or any of its parts. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply
to you.
6. CLAIM PROCEDURE
Any claim under this warranty should be initiated with the dealer who sold the boiler, or with any other dealer handling the warrantor’s products. If
this is not practicable, the owner should contact:
U. S. Customers
Canadian Customers
A. O. Smith Corporation
5621 West 115th Street
Alsip, IL 60803
A. O. Smith Enterprises Ltd.
P. O. Box, 310 - 768 Erie Street
Stratford, Ontario N5A 6T3
Telephone: 1-800-265-8520
Telephone: 1-800-323-2636
a. The warrantor will only honor replacement with identical or similar parts thereof which are manufactured or distributed by the warrantor.
b. Dealer replacements are made subject to in-warranty validation by warrantor.
7. DISCLAIMERS
NO OTHER EXPRESS WARRANTY HAS BEEN OR WILLBE MADE IN BEHALF OFTHE WARRANTOR WITH RESPECTTO THE MERCHANTABILITYOF
THE BOILER ORTHE INSTALLATION, OPERATION, REPAIR OR REPLACEMENTOF THE BOILER. THE WARRANTOR SHALLNOTBE RESPONSIBLE
FOR WATER DAMAGE, LOSS OF USE OFTHE UNIT, INCONVENIENCE, LOSS OR DAMAGETO PERSONALPROPERTY, OR OTHER CONSEQUENTIAL
DAMAGE. THE WARRANTOR SHALL NOT BE LIABLE BY VIRTUE OF THIS WARRANTY OR OTHERWISE FOR DAMAGE TO ANY PERSONS OR
PROPERTY, WHETHER DIRECTOR INDIRECT,AND WHETHERARISING IN CONTRACT OR TORT.
a. Some states or provinces do not allow the exclusion or limitation of the incidental or consequential damage, so the above limitations or exclusions
may not apply to you.
b. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Fill in the following for your own reference. Keep it. Registration is not a condition of warranty. The model and serial number are found on the
boiler’s rating plate.
Owner___________________________________________________________________________________________________________________
Installation Address________________________________________________________________________________________________________
City and State/Province _________________________________________________________Postal/Zip Code_______________________________
Date Installed _________________________________ Model No. ___________________________
Serial No.________________________
Dealer’s Name ____________________________________________________________________ Phone No._______________________________
Dealer’s Address__________________________________________________________________________________________________________
FILL IN DATA AND KEEP FOR FUTURE REFERENCE
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS
5621 W. 115TH STREET, ALSIP, IL 60803
PHONE: 1-800-433-2545 FAX: 1-800-433-2515
Download from Www.Somanuals.com. All Manuals Search And Download.
|