Quick Start Guide
UDM-RX02 Endeleo Multi-Format Receiver
Configuration
Overview
The UDM-RX02 is configured via the UDM Hub’s WebConsole. Refer to the UDM
Installed at the display device, the UDM-RX02 (FG-UDM-RX02) converts the signal
received from a UDM Multi-Format Distribution Hub to standard A/V signals (FIG. 1).
Hub’s Operation/Reference Guide for details.
Rear Panel Components
All of the connectors and ports are located on the rear panel (FIG. 2):
Composite (Pr) port
Composite (Pb) port
Composite (Y) port
UDM HUB port (RJ45) - from an
“OUTPUT” port on the UDM-0102
VGA (HD15) port
S-Video port
CVBS port
Serial port (RJ12)
FIG. 1 UDM-RX02
With all the same features of the UDM-RX01, the UDM-RX02 adds support for
“Common” mode sync, as well as remote power for long cable distance runs.
Compatibility
The UDM-RX02 is compatible for use with the following UDM Hubs:
IR Rx port
IR Tx port
RCA audio
•
•
•
•
UDM-0102 (FG-UDM-0102) - This hub supports Common Synch Mode.
UDM-0404 (FG-UDM-0404) - This hub supports Common Synch Mode.
UDM-1604 (FG-UDM-1604C) - This hub supports Common Synch Mode.
UDM-1604 (FG-UDM-1604) - This hub does not support Common Synch Mode.
In this case, the UDM-RX02 will function, but without Common Synch Mode.
(left/right)
Power connector
SPDIF female Digital Audio port
FIG. 2 UDM-RX02 - rear panel components
UDM Hub Port (RJ45)
The UDM-RX02 connects to a UDM Hub through a Cat 5/Cat 6 connection. Refer to
the UDM Hub’s Operation/Reference Guide for details.
Product Specifications
UDM-RX02 Specifications
Serial Port
Power Requirements:
24VDC @ .75A
The Serial port is available for diagnostic and troubleshooting purposes.
The Serial port on the UDM-RX02 is an RJ12 connector, and requires a DB9-to-RJ12
adapter cable (FG-RS01) to connect to a PC for Terminal control.
Note: In most cases the UDM-RX02 is remotely powered
by the UDM Multi-Format Distribution Hub (see Powering
IR Receiver (IR Rx) Port
Rear Panel Connectors:
The IR Rx port is used to enable user control and the remote compensation of the
video link to the UDM, using the FG-UDM-RC10 and the FG-IR03.
Power Socket:
2.1mm barrel-style DC power socket (female)
UDM Hub (RJ45)
Port:
Provides audio/video transport as well as control via Cat5,
Cat5e or Cat6 to an UDM Hub.
Refer to the Protocols and IR Learning section of the UDM Hub’s Operation/Reference
Guide for details for information on learning a device’s IR commands.
Serial (RJ12) port:
Enables an administrator to control the various functions
to the UDM-RX02 from a command line prompt and termi-
nal connection.
IR Transmit (IR Tx) Port
The IR Tx port issues IR commands from the UDM-RX02 to a controlled display
device (TV monitor or display). One IR display device can be connected to the UDM-
RX02 via the IR Tx port, and controlled via the UDM Hub’s WebConsole or via remote
control.
• Requires a DB9-to-RJ12 adapter cable (FG-RS01) to
connect to a PC.
• 9600, 8 bit, No Parity, 1 Stop Bit
Connecting an IR Device to the IR Tx Port
1.
Connect an IR01 Endeleo IR Emitter Module (FG-IR01) to the IR Tx port on the
UDM-RX02.
IR Rx Port:
3.5mm stereo input port, for connection of an IR receiver
to allow setup of the UDM-RX02, local compensation
controls, and remote control of centrally located IR
devices.
Note: Ensure the position of the device corresponds to the position assigned in
the Devices option of the UDM- Hub’s WebConsole.
Run the other end of the IR Emitter cable to the device’s IR sensor, and attach
the IR Emitter to the device’s sensor by removing the cover on the reverse side
of the IR Emitter.
2.
IR Tx Port:
3.5mm stereo IR Transmitter output port allows one IR-
controlled device (such as a DVD or VCR player) to be
controlled via optional wired IR emitter.
IR commands for each device on the system have to be learned by the UDM-0102 in
order to function properly. Refer to the Protocols and IR Learning section of the UDM
Hub’s Operation/Reference Guide for information on learning a device’s IR
commands.
Audio Connectors:
• Black RCA female connector - Digital audio
• White RCA female connector - Analog audio Left
• Red RCA female connector - Analog audio Right
AUDIO Connectors
The UDM-RX02 provides standard Audio RCA output connectors for S/PDIF for digital
audio, and LEFT/RIGHT for analog audio output (FIG. 2).
Video Connectors:
• Yellow RCA female connector - CVBS (supports
composite video)
• S-Video - S-video female connector
• VGA - HD15 female connector (supports VGA video)
• Green RCA female connector - Component output: Y
• Blue RCA female connector - Component output: Pb
• Red RCA female connector - Component output: Pr
VIDEO Connectors
VGA Input at Display Device
1.
2.
3.
Attach one end of the VGA cable to the VGA connector on the UDM-RX02.
Run the other end to the VGA connector on the display device. Connect firmly.
If appropriate connect audio to the audio connectors on the UDM-RX02.
Note: Ensure the UDM Hub port the RX02 is attached to is configured correctly
within the Hub’s configuration software. Also ensure the correct Audio Type
(Analog L/R, S/PDIF, or None) is selected for the relevant input.
Operating Environment: • 35°F - 95°F (5°C - 35°C)
• Max. relative humidity - 85% (non-condensing)
Dimensions (HWD):
Weight:
1" x 8 15/16” x 3 3/8” (25 mm x 227 mm x 85 mm)
1.45 lb. (658 g)
Composite Input at Display Device
1.
2.
3.
Attach the composite cable (normally yellow) to the CVBS connector on the
UDM-RX02.
Run the other end of the composite cable to the Composite connector (normally
yellow) on the display device. Connect firmly.
Certifications:
• CE
• FCC part 15 Class A
Other AMX Equipment: • RS232 DB9/RJ12 Connection Cable (FG-RS01)
If appropriate connect audio to the audio connectors on the UDM-RX02.
• UDM-RC02 Multi-Format IR Remote Control
(FG-UDM-RC02)
SVideo Input at Display Device
• IR01 IR Emitter Module (FG-IR01)
1.
2.
Attach the SVideo cable to the 4-pin S Video connector on the UDM-RX02.
Run the other end of the SVideo cable to the SVideo connector on the display
device. Connect firmly.
• IR03 External IR Receiver Module (FG-IR03)
• UDM-PS 24VDC, 750mA Power Supply (FG-UDM-PS)
3.
If appropriate connect audio to the audio connectors on the UDM-RX02.
Download from Www.Somanuals.com. All Manuals Search And Download.
|