ADTRAN Cordless Telephone 1202076L1 User Manual

TSU 600

TSU 600e

User Manual

Part Numbers

1202076L1

1202076L1#DC

1202076L2

1202076L2#DC

October 1998

61202076L1-1C

Download from Www.Somanuals.com. All Manuals Search And Download.

YEAR 2000 Compliance

All ADTRAN transmission hardware and software products have been tested

and found to be fully compliant with the YEAR 2000 requirements. This is true

for all models and revisions regardless of the date of manufacture or delivery.

Users who wish to independently verify that specific products are in compli-

ance may contact ADTRAN Technical Support at 1-888-423-8726 for additional

information

Download from Www.Somanuals.com. All Manuals Search And Download.

FCC REGULATIONS REQUIRE THAT THE FOLLOWING INFORMATION BE

PROVIDED TO THE CUSTOMER IN THIS MANUAL

1. This equipment complies with Part 68 of the FCC rules. The required

label is attached to the bottom of the chassis.

2. An FCC compliant telephone cord and modular plug is provided

with this equipment. This equipment is designed to be connected to

the telephone network or premises wiring using a compatible modu-

lar jack which is Part 68 compliant. See installation instructions for

details.

3. If your Product causes harm to the telephone network, the Telephone

Company may discontinue your service temporarily. If possible,

they will notify you in advance. If advance notice is not practical, you

will be notified as soon as possible. You will be advised of your right

to file a complaint with the FCC.

4. Your telephone company may make changes in its facilities, equip-

ment, operations, or procedures that could affect the proper opera-

tion of your equipment. If they do, you will be given advance notice

so as to give you an opportunity to maintain uninterrupted service.

5. If you experience trouble with the equipment Product, please contact

ADTRAN at (256) 963-8000 for repair/warranty information. The

telephone company may ask you to disconnect this equipment from

the network until the problem has been corrected, or until you are

sure the equipment is not malfunctioning.

6. This unit contains no user serviceable parts.

7. The following information may be required when applying to your

local telephone company for leased line facilities.

Service Type

1.544 Mbps -SF

REN/SOC

FIC

USOC

6.0N

04DU9-BN

04DU9-DN

RJ-48C

1.544 Mbps - SF and B8ZS

1.544 Mbps - ESF

04DU9-1KN RJ-48C

04DU9-1SN RJ-48C

1.544 Mbps - ESF and B8ZS

Download from Www.Somanuals.com. All Manuals Search And Download.

FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY

INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for

a Class A digital device, pursuant to Part 15 of the FCC Rules. These lim-

its are designed to provide reasonable protection against harmful inter-

ference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio frequencies. Operation of this

equipment in a residential area is likely to cause harmful interference in

which case the user will be required to correct the interference at his

own expense.

Shielded cables must be used with this unit to ensure compliance with

Class A FCC limits.

Changes or modifications to this unit not expressly approved by the

party responsible for compliance could void the user’s authority to op-

erate the equipment.

Download from Www.Somanuals.com. All Manuals Search And Download.

CANADIAN EMISSIONS REQUIREMENTS

This digital apparatus does not exceed the Class A limits for radio noise

emissions from digital apparatus as set out in the interference-causing

equipment standard entitled “Digital Apparatus,” ICES-003 of the De-

partment of Communications.

Cet appareil nuerique respecte les limites de bruits radioelectriques ap-

plicables aux appareils numeriques de Class A prescrites dans la norme

sur le materiel brouilleur: “Appareils Numeriques,” NMB-003 edictee

par le ministre des Communications.

Download from Www.Somanuals.com. All Manuals Search And Download.

CANADIAN EQUIPMENT LIMITATIONS

The Industry Canada Certification label identifies certified equipment.

This certification means that the equipment meets certain telecommu-

nications network protective, operational, and safety requirements.

The Department does not guarantee the equipment will operate to the

user's satisfaction.

Before installing this equipment, users should ensure that it is permissi-

ble to be connected to the facilities of the local telecommunications com-

pany. The equipment must also be installed using an acceptable method

of connection. In some cases, the company's inside wiring associated

with a single line individual service may be extended by means of a cer-

tified connector assembly (telephone extension cord). The customer

should be aware that compliance with the above conditions may not

prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Cana-

dian maintenance facility designated by the supplier. Any repairs or al-

terations made by the user to this equipment, or equipment

malfunctions, may give the telecommunications company cause to re-

quest the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground

connections of the power utility, telephone lines and internal metallic

waterpipe system, if present, are connected together. This precaution

may be particularly important in rural areas.

Users should not attempt to make such connections themselves, but should con-

tact the appropriate electric inspection authority, or an electrician, as appropri-

ate.

The Load Number (LN) assigned to each terminal device denotes the

percentage of the total load to be connected to a telephone loop which is

used by the device, to prevent overloading. The termination on a loop

may consist of any combination of devices subject only to the equipment

that the total of the LNs of all devices does not exceed 100.

The ringer equivalence number (REN) assigned to each terminal adapt-

er is used to determine the total number of devices that may be connect-

ed to each circuit. The sum of the RENs from all devices in the circuit

should not exceed a total of 5.0.

Download from Www.Somanuals.com. All Manuals Search And Download.

AFFIDAVIT REQUIREMENTS FOR CONNECTION

TO DIGITAL SERVICES

• An affidavit is required to be given to the telephone company when-

ever digital terminal equipment without encoded analog content and

billing protection is used to transmit digital signals containing encod-

ed analog content which are intended for eventual conversion into

voiceband analog signals and transmitted on the network.

• The affidavit shall affirm that either no encoded analog content or

billing information is being transmitted or that the output of the de-

vice meets Part 68 encoded analog content or billing protection spec-

ifications.

• End user/customer will be responsible to file an affidavit with the lo-

cal exchange carrier when connecting unprotected CPE to a 1.544

Mbps or subrate digital services.

• Until such time as subrate digital terminal equipment is registered for

voice applications, the affidavit requirement for subrate services is

waived.

Download from Www.Somanuals.com. All Manuals Search And Download.

AFFIDAVIT FOR CONNECTION OF CUSTOMER PREMISES

EQUIPMENT TO 1.544 MBPS AND/OR SUBRATE DIGITAL SERVICES

For the work to be performed in the certified territory of

______________________________(telco name)

State of _________________________________

County of ________________________________

I, ___________________________________ (name),

(business address), ______________________ (telephone number) being

duly sworn, state:

I have responsibility for the operation and maintenance of the terminal

equipment to be connected to 1.544 Mbps and/or ________ subrate dig-

ital services. The terminal equipment to be connected complies with

Part 68 of the FCC rules except for the encoded analog content and bill-

ing protection specifications. With respect to encoded analog content

and billing protection:

( ) I attest that all operations associated with the establishment, main-

tenance, and adjustment of the digital CPE with respect to analog con-

tent and encoded billing protection information continuously complies

with Part 68 of the FCC Rules and Regulations.

( ) The digital CPE does not transmit digital signals containing encoded

analog content or billing information which is intended to be decoded

within the telecommunications network.

( ) The encoded analog content and billing protection is factory set and

is not under the control of the customer.

I attest that the operator(s)/maintainer(s) of the digital CPE responsible

for the establishment, maintenance, and adjustment of the encoded an-

alog content and billing information has (have) been trained to perform

these functions by successfully having completed one of the following

(check appropriate blocks):

( ) A. A training course provided by the manufacturer/grantee of the

equipment used to encode analog signals; or

Download from Www.Somanuals.com. All Manuals Search And Download.

( ) B. A training course provided by the customer or authorized repre-

sentative, using training materials and instructions provided by the

manufacturer/grantee of the equipment used to encode analog signals;

( ) C. An independent training course (e.g., trade school or technical

institution) recognized by the manufacturer/grantee of the equipment

used to encode analog signals; or

( ) D. In lieu of the preceding training requirements, the operator(s)/

maintainer(s) is (are) under the control of a supervisor trained in accor-

dance with _________ (circle one) above.

I agree to provide _________________ (telco's name) with proper docu-

mentation to demonstrate compliance with the information as provided

in the preceding paragraph, if so requested.

_________________________________Signature

_________________________________Title

_________________________________ Date

Transcribed and sworn to before me

This ________ day of ________, 199___

_________________________________

Notary Public

My commission expires:

_________________________________

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment, please follow these basic safety

precautions to reduce the risk of fire, electrical shock, or personal injury:

Do not use this product near water, such as near a bath tub,

wash bowl, kitchen sink, laundry tub, in a wet basement,

or near a swimming pool.

Avoid using a telephone (other than a cordless-type) dur-

ing an electrical storm. There is a remote risk of shock from

lightning.

Do not use the telephone to report a gas leak in the vicinity

of the leak.

Use only the power cord, power supply, and/or batteries

indicated in the manual. Do not dispose of batteries in a

fire. They may explode. Check with local codes for special

disposal instructions.

Download from Www.Somanuals.com. All Manuals Search And Download.

Warranty and Customer Service

ADTRAN will replace or repair this product within five years from the

date of shipment if the product does not meet its published specifica-

tions or if it fails while in service. For detailed warranty, repair, and re-

turn information refer to the ADTRAN Equipment Warranty and Repair

and Return Policy Procedure.

Return Material Authorization (RMA) is required prior to returning

equipment to ADTRAN.

For Service, RMA requests, or more information, contact ADTRAN Cus-

tomer Service listed on the inside back cover of this manual.

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

Chapter 1 Introduction .......................................................................................... 1-1

TSU 600 Overview .................................................................................................... 1-1

Product Description.......................................................................................... 1-1

Standard Features in the TSU 600................................................................... 1-2

TSU Option Modules........................................................................................ 1-3

Option Module Architecture ........................................................................... 1-4

TSU 600 Configuration Applications .................................................................... 1-5

Router, PBX, Video Conferencing Application............................................. 1-5

Drop and Insert, Voice, and Router Application.......................................... 1-6

Chapter 2 Installation ............................................................................................ 2-1

Unpack, Inspect, Power Up .................................................................................... 2-1

Receipt Inspection ............................................................................................. 2-1

ADTRAN Shipments Include.......................................................................... 2-1

Customer Provides............................................................................................ 2-1

Power Connection............................................................................................. 2-2

DC Powered Units ..................................................................................... 2-2

Backup Power Supply (600e only) ........................................................... 2-2

Installing and Replacing the Power Supply ................................... 2-3

Grounding Instructions ........................................................................................... 2-4

Identification of Rear Panel Layout ....................................................................... 2-5

TSU 600 Interfaces............................................................................................. 2-9

Network Interface ...................................................................................... 2-9

Network Test Interface .............................................................................. 2-9

Control Port Input ...................................................................................... 2-9

Chain Port Output ..................................................................................... 2-9

10BaseT Interface (600e only) ................................................................. 2-10

Option Slot Arrangement............................................................................... 2-10

Power-up Testing ............................................................................................ 2-11

Self-Test ..................................................................................................... 2-11

Board level tests ................................................................................ 2-12

Unit level tests ................................................................................... 2-12

Initialization ..................................................................................................... 2-12

61202076L1-1

TSU 600 User Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

Set User Passcode .....................................................................................2-12

Set Unit Identification ..............................................................................2-12

Set Control Port ........................................................................................2-13

Chain-In (PC) ............................................................................................2-13

Chain In/Chain Out ................................................................................2-13

Normal Power-Up Procedure........................................................................ 2-14

Chapter 3 Operation ...............................................................................................3-1

Front Panel .................................................................................................................3-1

CSU Status LEDs ............................................................................................... 3-2

Module Status LEDs ......................................................................................... 3-3

Operation Keys .................................................................................................. 3-5

General Menu Operation ..........................................................................3-5

Selecting and Activating a Menu Item ....................................................3-6

Editing the Data Field ................................................................................3-7

Display Only Data Fields ..........................................................................3-8

Exit Any Menu Field Operation Or Display ..........................................3-8

Data Port Identification .................................................................................... 3-9

Front Panel Menu Structure........................................................................... 3-10

Alternate Methods of Control........................................................................ 3-11

T-Watch PRO (ADTRAN PC Program) ................................................3-11

T-Watch PRO/LAN Connection .................................................... 3-11

T-Watch PRO/EIA-232 Connection ............................................... 3-12

SNMP .........................................................................................................3-12

Terminal Mode Connection ....................................................................3-13

Telnet Connection ....................................................................................3-13

Chapter 4 Status Menu ..........................................................................................4-1

Network Performance Reports (NI PERF RPTS).......................................... 4-2

Network Interface Errors (NI ERRORS) ........................................................ 4-3

Active Alarms .................................................................................................... 4-4

View History ...................................................................................................... 4-4

Port Status........................................................................................................... 4-5

Remote Port........................................................................................................ 4-5

Clear Port Alarm................................................................................................ 4-5

ENET Status (600e only)................................................................................... 4-6

PS Status (600e only) ......................................................................................... 4-6

Chapter 5 Configuration Menu ............................................................................5-1

Network (NI) .............................................................................................................5-2

Network (NI) Menu Items ............................................................................... 5-2

TSU 600 Clock Sources ..................................................................................... 5-4

Network Timing .........................................................................................5-4

DTE Timing .................................................................................................5-5

U-BR1TE (Slot 1) .........................................................................................5-5

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

Internal Timing ........................................................................................... 5-6

Secondary Timing ...................................................................................... 5-7

Normal (CSU) Timing ............................................................................... 5-8

Unit Menu .......................................................................................................... 5-9

Map Exchange (Map Xchng) Menu............................................................. 5-11

MAP In Use: A(B) Menu ............................................................................... 5-11

DS0 Map A and DS0 Map B Menu .............................................................. 5-12

Create Temp Example ............................................................................. 5-13

Port Configuration (Port Config)................................................................. 5-15

Chapter 6 Utility Menu ......................................................................................... 6-1

Time/Date.......................................................................................................... 6-2

Factory Restore .................................................................................................. 6-2

Set Passcode ....................................................................................................... 6-2

Enter Passcode from Other Menus .......................................................... 6-2

Change/Set a Passcode ............................................................................. 6-3

Automatic Time-out Feature .................................................................... 6-3

No Passcode Desired ................................................................................. 6-3

Unit ID ................................................................................................................ 6-3

Setting the Unit Identification .................................................................. 6-4

No Unit ID Desired .................................................................................... 6-4

Software Revision (Software Rev) .................................................................. 6-4

Port Utility.......................................................................................................... 6-4

ENET Address (600e only)............................................................................... 6-4

CMD Mode......................................................................................................... 6-4

Chapter 7 Test Menu .............................................................................................. 7-1

Network Tests.................................................................................................... 7-2

Loopback Tests ........................................................................................... 7-2

Network Interface Loopbacks........................................................... 7-3

Local Loopbck.................................................................................................... 7-3

Remote Loopbk.................................................................................................. 7-4

Test Pattern ....................................................................................................... 7-5

QRSS Pattern ............................................................................................... 7-5

Pattern Result..................................................................................................... 7-6

Run Self-Test ...................................................................................................... 7-7

Board level tests ......................................................................................... 7-7

Unit level tests ............................................................................................ 7-7

Port Tests ............................................................................................................ 7-8

Cancel Tests........................................................................................................ 7-8

Chapter 8 Telnet/Terminal Menus ...................................................................... 8-1

Main Menu ................................................................................................................ 8-1

Status, Config, Util, and Test Menu Options ................................................ 8-2

DS0 Maps Configuration Menu ............................................................... 8-2

61202076L1-1

TSU 600 User Manual

iii

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

Initializing the Temp Map ................................................................. 8-3

Editing the Temp Map ....................................................................... 8-4

Applying the Temp Map ................................................................... 8-4

Reviewing Maps.................................................................................. 8-4

Remote Menu Access........................................................................................ 8-5

Management Configuration............................................................................. 8-5

Unit Access Table .......................................................................................8-5

Add New Unit..................................................................................... 8-6

Modify Unit ......................................................................................... 8-6

Delete Unit ........................................................................................... 8-6

Default Unit Passcode ........................................................................ 8-7

OK ......................................................................................................... 8-7

SNMP Read Community.................................................................................. 8-7

SNMP Read/Write Community ..............................................................8-7

SNMP Trap Community ...........................................................................8-8

System Name ..............................................................................................8-8

System Contact ...........................................................................................8-8

System Location ..........................................................................................8-8

Auto. Fail Traps Sent .................................................................................8-9

Poll Link Status Traps Sent .......................................................................8-9

Ping IP Host ................................................................................................8-9

Telnet/Terminal Time-out ........................................................................8-9

Telnet/Terminal Password .......................................................................8-9

Exit ................................................................................................................8-9

Flash Download................................................................................................. 8-9

Quit Session........................................................................................................ 8-9

Appendix A Understanding SNMP ................................................................... A-1

Appendix B Understanding TR-08..................................................................... B-1

Appendix C Network Pinouts............................................................................. C-1

Appendix D System Messages............................................................................ D-1

Appendix E Specifications.................................................................................... E-1

Index....................................................................................................................Index-1

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

List of Figures

Figure 1-1. TSU 600 Option Modules ................................................................... 1-4

Figure 1-2. Router, PBX, Video Conferencing Application Set Up .................. 1-5

Figure 1-3. Drop and Insert, Voice, and Router Application Set Up ............... 1-6

Figure 2-1a. TSU 600 Rear Panel ............................................................................ 2-5

Figure 2-1b. TSU 600 with DC Power Rear Panel............................................... 2-6

Figure 2-1c. TSU 600e Rear Panel.......................................................................... 2-7

Figure 2-1d. TSU 600e with DC Power Rear Panel............................................. 2-8

Figure 2-2. TSU 600 Interfaces ............................................................................... 2-9

Figure 2-3. TSU 600 Slot Designation (Rear View) ........................................... 2-10

Figure 2-4. Example of Chain In.......................................................................... 2-13

Figure 3-1. TSU 600 Front Panel Layout .............................................................. 3-4

Figure 3-2. Example of Basic Front Panel Menu Travel..................................... 3-6

Figure 3-3. Display and Data Fields...................................................................... 3-8

Figure 3-4. Module Slots, TSU 600........................................................................ 3-9

Figure 4-1. Complete Status Menu........................................................................ 4-1

Figure 4-2. Network Interface Performance Report........................................... 4-2

Figure 4-3. Display of Alarm Messages ............................................................... 4-4

Figure 5-1. Configuration Menu............................................................................ 5-1

Figure 5-2. Network Timed Clock Source............................................................ 5-4

Figure 5-3. DTE Timed Clock Source ................................................................... 5-5

Figure 5-4. Internal Clock Source.......................................................................... 5-6

Figure 5-5. Secondary Clock Source ..................................................................... 5-7

Figure 5-6. Normal (CSU)....................................................................................... 5-8

Figure 5-7. DS0 Map Designations...................................................................... 5-12

Figure 5-8. Create Temp Selection Screen.......................................................... 5-14

Figure 6-1. Utility Menu Tree ................................................................................ 6-1

Figure 7-1. Test Menu ............................................................................................. 7-1

Figure 7-2. Network Loopback Tests.................................................................... 7-3

Figure 8-1. Telnet/Terminal Main Menu............................................................. 8-1

Figure 8-2. DS0 Temp Map .................................................................................... 8-2

Figure 8-3. Unit Access Table ................................................................................ 8-6

61202076L1-1

TSU 600 User Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

List of Figures

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

List of Tables

Table B-1. Alarm Conditions ................................................................................. B-2

Table B-2. TR-08 DS0 Conversion Table .............................................................. B-3

Table C-1. Network Pinouts.................................................................................. C-1

Table C-2. Control In/Chain In Pinout ............................................................... C-2

Table C-3. Chain-Out Pinout ................................................................................ C-3

Table C-4. 10BaseT Ethernet ................................................................................. C-4

61202076L1-1

TSU 600 User Manual

vii

Download from Www.Somanuals.com. All Manuals Search And Download.

List of Tables

viii

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Introduction

Chapter 1

TSU 600 OVERVIEW

This manual covers the use of the following products:

• TSU 600

• TSU 600 with DC power

• TSU 600e

• TSU 600e with DC power

Unless otherwise stated, the TSU 600 refers to all four products.

Product Description

The TSU 600 is a T1/FT1 multiplexer with six option slots and embed-

ded SNMP management. The TSU 600’s six option slots accept one of

many available option modules for voice and data applications. Each

module offers up to four ports for a total of 24 possible voice or data

ports.

The TSU 600 serves as the link between user data sources such as:

• local area network (LAN) bridges

• routers,

• computers,

• CAD systems,

• teleconferencing equipment, and

• PBXs.

Through the use of multiple data ports, the TSU 600 can simultaneously

connect one or more of these devices to a T1 circuit. The amount of

bandwidth allocated to each port is custom-programmable. You can

manually allocate bandwidth or set the bandwidth to change automati-

cally at predetermined times to use the available bandwidth most ad-

vantageously.

61202076L1-1

TSU 600 User Manual

1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 1. Introduction

Changes in the configuration do not disrupt data flow in channels that

are not being reconfigured. The unique architecture and the availability

of option modules provides a path for growth to accommodate future

requirements.

The TSU 600 offers a wide variety of network management options. You

can manage via SNMP through the 10BaseT (600e only) or chain-in

ports. If you are using T-Watch PRO, a Microsoft Windows® program,

you can manage the TSU 600 via the same 10BaseT (600e only) or chain-

in ports. An enhanced VT-100 terminal interface is also provided.

Standard Features in the TSU 600

The standard features of the TSU 600 are listed below:

• A single T1 interface

• Six slots to house option modules with up to four additional data

ports, including voice

• Architecture that allows mix of port types to meet the data interface

requirements

• Easy configuration capabilities using simplistic menus displayed in a

liquid crystal display (LCD) window operated by a front panel key-

pad

• SNMP, Telnet, and T-Watch PRO management via SLIP or 10BaseT

(600e only)

• Ability to proxy for “agentless” units

• Enhanced terminal mode

• Support for a redundant AC power supply (600e only)

• Two programmable configuration maps that define the bandwidth

allocation between data ports

• Data drop and insert, as well as full drop and insert

• Flash memory for software updates

• Timing selectable from the network, from the slot 1 data port, inter-

nally, or from a secondary interface

• QRSS; 511 test patterns using Nx option

• Fractional T1 loopbacks as defined in annex B of ANSI T1.403-1995

• Extensive self-testing and monitoring to ensure proper operation

1-2

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 1. Introduction

TSU Option Modules

Module Name

Description

DSX1

Short haul T1 interface for operation with a

PBX (Terminal Interface).

Full Drop and Insert

Permits the dropping of data and insertion of

new data into the same DS0 time slot. This

module includes a long haul DS1 interface. It

can also be used as a second DS1 interface to

provide up to 3 MB aggregate throughput.

Nx56/64 Serial Interface Provides a V.35 serial interface in either sin-

gle or dual versions.

NxIQ

Frame-relay aware device that provides

detailed information regarding the health

and performance of the frame relay circuit.

Voice Interface

OCU DP

2/4 channel FXS/FX0/E&M.

Interfaces to DDS or 4-wire Switched-56.

DSU DP

Provides two sync or async ports (232 or

V.35).

Dial Backup

U-BR1TE

Allows for backup of data upon network T1

failure.

Allows ISDN lines to be extended over a T1

line.

61202076L1-1

TSU 600 User Manual

1-3

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 1. Introduction

Option Module Architecture

The TSU 600 features a unique architecture that allows the addition of

six option modules and plug-on boards, providing an opportunity for

growth to accommodate many applications. See Figure 1-1. This unique

approach allows you to mix interface types to meet any application.

DSX-1

Module

TSU 600

OCU-DP

Module

Plug on

V.35

Module

Plug on

OCU DP

D&I

Module

DUAL

Voice

Plug on

Dual Voice

TSU 600 Option Modules

Figure 1-1.

1-4

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 1. Introduction

TSU 600 CONFIGURATION APPLICATIONS

The following examples illustrate possible configurations of TSU 600

applications.

Router, PBX, Video Conferencing Application

In this application, an Nx54/64 module provides a V.35 interface to a

router. The PBX is interfaced to the TSU 600 with the DSX-1 module. An

OCU DP module and OCU DP plug-on board provide two switched 56

circuits for video conferencing. The SLIP port or 10BaseT port (600e

only) allows SNMP network management over the LAN. See Figure 1-2.

PBX

TSU 600

ROUTER

SLIP or 10BaseT (600e only)

VIDEO

CONFERENCING

SNMP NETWORK

MANAGEMENT WORKSTATION

Router, PBX, Video Conferencing Application Set Up

Figure 1-2.

61202076L1-1

TSU 600 User Manual

1-5

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 1. Introduction

Drop and Insert, Voice, and Router Application

The TSU 600 provides a router interface with an Nx56/64 module. A

drop and insert module provides a second T1 interface to a remote TSU.

T-WATCH PRO (which runs on a PC) easily manages the network. FXO

modules are used to provide PBX extensions to remote sites. See Figure

1-3.

TSU 100

ENTER

REMOTE

ALARM

CLEAR

HOME

CANCEL

SHIFT

DSU

ALAR

MODULE

OK TEST

ALARM

CSU

ERROR

ALARM

ROUTER

T-WATCH

PBX

Drop and Insert, Voice, and Router Application

Set Up

Figure 1-3.

1-6

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Chapter 2

UNPACK, INSPECT, POWER UP

Receipt Inspection

Carefully inspect the TSU 600 for shipping damages. If you suspect

damage, file a claim immediately with the carrier and then contact ADT-

RAN Customer Service (see the inside last page of this manual). If pos-

sible, keep the original shipping container for use in shipping the TSU

600 back for repair or for verification of damage during shipment.

ADTRAN Shipments Include

• The TSU 600

• A line interface cable: an 8-position modular to

8-position modular (15 ft.)

• A DB-25 to modular adapter

• An 8-position, 6-foot modular cable for the

Chain-In port connection

• The User Manual

• Rackmount Brackets

• Rackmount Data Sheet

Customer Provides

• Cables for any expansion modules to be used with the TSU 600

• 10BaseT cable for connection to a LAN or router (if you plan to use

remote management features). This is for 600e only.

61202076L1-1

TSU 600 User Manual

2-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 2. Installation

Power Connection

The AC- powered TSU 600 is equipped with a captive, 8-foot power

cord, terminated by a 3-prong plug which connects to a grounded pow-

er receptacle.

Power to the TSU 600 must be from a grounded 90-120 VAC, 50/

60Hz source.

DC Powered Units

The DC-powered TSU 600 (1202076L1#DC or 1202076L2#DC) is

equipped with a terminal strip on the rear of the unit. The power source

should be connected to the terminal strip according to the polarity mark-

ings on the unit.

Example:

A -48V source would be connected with the -48V return attached to the

(+) terminal and the -48VDC attached to the (-) terminal. Power must be

from a DC source in the range of 21 to 26 VDC or in the range of 40 to

56VDC.

The protective cover should be reinstalled over the terminal strip once

the power source is connected.

The DC-powered TSU 600 is to be installed only in restricted areas (ded-

icated equipment rooms, equipment closets, etc.) in accordance with Ar-

ticles 110-16 and 110-18 of the National Electric Code, ANSI/NFPA 70.

Backup Power Supply (600e only)

The TSU 600e has two power supply slots on the right side of the chassis.

The base unit is shipped with a single power supply. The TSU 600e is

fully operational with only a single power supply, which may be in-

stalled on either the left (power supply A) or the right (power supply B).

You can install a backup supply in the unused slot. The red System

Alarm LED on the front panel will indicate failure of either supply.

2-2

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 2. Installation

Installing and Replacing the Power Supply

The following steps show how to install a new supply or replace a failed

supply.

Power does not have to be turned off on a working supply to add a new supply

or replace a failed one.

Step

Action

One Power Supply

If only one supply is installed in the chassis, remove the

blank panel covering the unused power supply slot.

Two Power Supplies

If two power supplies are installed, the failed supply can be

identified by the alarm on the front panel LCD. The alarm

message will identify a failure on Power Supply A or Power

Supply B. The option slot legend on the rear panel shows the

location of each power supply. Turn the power switch to Off

on the failed supply and unplug the power cord from the

power source.

Remove the two screws that secure the power supply mod-

ule to the TSU 600e chassis and remove the failed power sup-

ply module.

Remove the new power supply from the shipping con-

tainer. Make sure the power switch is in the Off position.

Plug the new supply into the open power supply slot and

install the two screws on the power supply module

Plug the new power supply cord into a grounded 115 VAC,

50/60 Hz power receptable.

Turn the power switch On.

61202076L1-1

TSU 600 User Manual

2-3

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 2. Installation

GROUNDING INSTRUCTIONS

The grounding instruction information is from the Underwriters' Labo-

ratory UL 1950, 3rd Edition.

An equipment grounding conductor that is not smaller in size than the

ungrounded branch-circuit supply conductors is to be installed as part

of the circuit that supplies the product or system.

• Bare, covered, or insulated grounding conductors are acceptable.

• Individually covered or insulated equipment grounding conductors

shall have a continuous outer finish that is either green, or green with

one or more yellow stripes.

• The equipment grounding conductor is to be connected to ground at

the service equipment.

• The attachment-plug receptacles in the vicinity of the product or sys-

tem are all to be of a grounding type.

• The equipment grounding conductors serving these receptacles are

to be connected to earth ground at the service equipment.

• A supplementary equipment grounding conductor shall be installed

between the product or system and ground that is in addition to the

equipment grounding conductor in the power-supply cord.

• The supplementary equipment grounding conductor shall not be

smaller in size than the ungrounded branch-circuit supply conduc-

tors.

• The supplementary equipment grounding conductor shall be con-

nected to the product at the terminal provided, and shall be connect-

ed to ground in a manner that will retain the ground connection

when the product is unplugged from the receptacle.

• The connection to ground of the supplementary equipment ground-

ing conductor shall be in compliance with the rules for terminating

bonding jumpers at Part K or Article 250 of the National Electrical

Code, ANSI/NFPA 70.

• Termination of the supplementary equipment grounding conductor

is permitted to be made to building steel, to a metal electrical raceway

system, or to any grounded item that is permanently and reliably

connected to the electrical service equipment ground.

• The supplemental grounding conductor shall be connected to the

equipment using a number 8 ring terminal.

• The terminal should be fastened to the grounding lug provided on

the rear panel of the equipment.

• The ring terminal should be installed using the appropriate crimping

tool (AMP P/N 59250 T-EAD Crimping Tool or equivalent).

2-4

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 2. Installation

IDENTIFICATION OF REAR PANEL LAYOUT

Figures 2-1a, Figure 2-1b, Figure 2-1c, and Figure 2-1d show the config-

uration for the rear panels of the TSU 600, TSU 600 with DC Power, TSU

600e, and TSU 600e with DC power.

CAUTION-RISK OF

ELECTRIC SHOCK

CAUTION:

MAINTENANCE TO BE

PERFORMED BY TRAINED

SERVICE PERSONEL ONLY

MODULE 1 MODULE 4

MODULE 2 MODULE 5

MODULE 3 MODULE 6

CONTROL

/CHAIN

SEE MANUAL BEFORE

REMOVING POWER SUPPLY

10 BASE T

OUT

IN OUT MON

NETWORK

ALL EMPTY SLOTS MUST BE

SUPPLEMENTAL EARTH GROUND MUST BE

CONNECTED PRIOR TO CONNECTION OF

TELECOMMUNICATION WIRING.

COVERED WITH BLANK PANELS

(600e ONLY)

DUAL

FXS

PORT X.1

PORT X.2

NX 56/64

PORT X.1

NX 56/64

PORT X.2

DUAL

FXS

PORT X.3

1A/250V

PORT X.3

PORT X.4

V.35

90-130 VAC

60 HZ

.7A MAX

CAUTION:

IN OUT MON

FOR CONTINUED PROTECTION

AGAINST RISK OF FIRE, REPLACE

ONLY WITH SAME TYPE AND RATING

OF FUSE

SEC. NI

NX 56/64

PORT X.2

PORT X.1

DS-1

V.35

T1 Monitor/Test Jacks

T1 Network Connection

Control In/Out Connection

Power Switch

Blank panel covering an unused option slot

Example of option modules installed

Power Cord

1A/250V Fuse

TSU 600 Rear Panel

Figure 2-1a.

61202076L1-1

TSU 600 User Manual

2-5

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 2. Installation

CAUTION-RISK OF

ELECTRIC SHOCK

CAUTION:

MAINTENANCE TO BE

PERFORMED BY TRAINED

SERVICE PERSONEL ONLY

MODULE 1 MODULE 4

MODULE 2 MODULE 5

MODULE 3 MODULE 6

CONTROL

/CHAIN

SEE MANUAL BEFORE

REMOVING POWER SUPPLY

10 BASE T

OUT

IN OUT MON

NETWORK

ALL EMPTY SLOTS MUST BE

SUPPLEMENTAL EARTH GROUND MUST BE

CONNECTED PRIOR TO CONNECTION OF

TELECOMMUNICATION WIRING.

COVERED WITH BLANK PANELS

(600e ONLY)

DUAL

FXS

PORT X.1

PORT X.2

NX 56/64

PORT X.1

NX 56/64

PORT X.2

DUAL

FXS

PORT X.3

5A/250V

PORT X.3

PORT X.4

V.35

24/48 VDC

CAUTION:

IN OUT MON

FOR CONTINUED PROTECTION

AGAINST RISK OF FIRE, REPLACE

ONLY WITH SAME TYPE AND RATING

OF FUSE.

SEC. NI

NX 56/64

PORT X.2

PORT X.1

DS-1

V.35

T1 Monitor/Test Jacks

T1 Network Connection

Control In/Out Connection

Power Switch

Blank panel covering an unused option slot

Example of option modules installed

Power Input Terminals

5A/250V Fuse

TSU 600 with DC Power Rear Panel

Figure 2-1b.

2-6

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 2. Installation

CAUTION-RISK OF

ELECTRIC SHOCK

CAUTION:

MAINTENANCE TO BE

MODULE 1 MODULE 4

MODULE 2 MODULE 5

MODULE 3 MODULE 6

PERFORMED BY TRAINED

SERVICE PERSONEL ONLY

CONTROL

/CHAIN

SEE MANUAL BEFORE

REMOVING POWER SUPPLY

10 BASE T

OUT

IN OUT MON

NETWORK

ALL EMPTY SLOTS MUST BE

SUPPLEMENTAL EARTH GROUND MUST BE

CONNECTED PRIOR TO CONNECTION OF

TELECOMMUNICATION WIRING.

COVERED WITH BLANK PANELS

(600e ONLY)

DUAL

FXS

PORT X.1

PORT X.2

NX 56/64

PORT X.1

NX 56/64

PORT X.2

DUAL

FXS

PORT X.3

PORT X.4

V.35

90-120 VAC

50/60 HZ.

.7A MAX

90-120 VAC

50/60 HZ.

.7A MAX

IN OUT MON

SEC. NI

NX 56/64

PORT X.2

PORT X.1

DS-1

V.35

T1 Monitor/Test Jacks

T1 Network Connection

10BaseT Connection

Control In/Out Connection

Power Switch

Blank panel covering an unused option slot

Example of option modules installed

Power Supply B (if installed)

TSU 600e Rear Panel

Figure 2-1c.

61202076L1-1

TSU 600 User Manual

2-7

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 2. Installation

CAUTION-RISK OF

ELECTRIC SHOCK

CAUTION:

MAINTENANCE TO BE

PERFORMED BY TRAINED

SERVICE PERSONEL ONLY

MODULE 1 MODULE 4

MODULE 2 MODULE 5

MODULE 3 MODULE 6

CONTROL

/CHAIN

SEE MANUAL BEFORE

REMOVING POWER SUPPLY

10 BASE T

OUT

IN OUT MON

NETWORK

ALL EMPTY SLOTS MUST BE

SUPPLEMENTAL EARTH GROUND MUST BE

CONNECTED PRIOR TO CONNECTION OF

TELECOMMUNICATION WIRING.

COVERED WITH BLANK PANELS

(600e ONLY)

DUAL

FXS

PORT X.1

PORT X.2

NX 56/64

PORT X.1

NX 56/64

PORT X.2

DUAL

FXS

PORT X.3

5A/250V

PORT X.3

PORT X.4

V.35

24/48 HZ.

CAUTION:

IN OUT MON

FOR CONTINUED PROTECTION

AGAINST RISK OF FIRE, REPLACE

ONLY WITH SAME TYPE AND RATING

OF FUSE.

SEC. NI

NX 56/64

PORT X.2

PORT X.1

DS-1

V.35

T1 Monitor/Test Jacks

T1 Network Connection

10BaseT Connection

Control In/Out Connection

Power Switch

5A/250V Fuse

Blank panel covering an unused option slot

Example of option modules installed

Power Input Terminals

TSU 600e with DC Power Rear Panel

Figure 2-1d.

2-8

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 2. Installation

TSU 600 Interfaces

The TSU 600 is equipped with six option slots, management interfaces,

and a T1 interface, in the rear panel. See Figure 2-2.

LAN

PC or Modem

Control

Input

Chain

Output

Chain

Input

Chain

Output

10BaseT

(600e only)

TSU 600

Option

Network

TSU 600 Interfaces

Figure 2-2.

Network Interface

The network interface (NI) port provides the connection to the T1. This

port complies with the applicable ANSI and AT&T standards. For more

information, see Wiring on page B-1.

Network Test Interface

The IN and OUT test jacks for the network interface provide intrusive

test capability for the incoming T1. By connecting to these jacks with test

equipment, the T1 connection will be broken, and the test equipment

will terminate the incoming T1. The MON test jack provides a bridged

access jack for non-intrusive monitoring of the incoming T1. When con-

nected to this jack, the test equipment should be configured for a

bridged termination.

Control Port Input

The control port input provides an EIA-232 input from a PC or a modem

for control of the TSU 600. You can also use it as a chain input from an-

other TSU 600 or TSU 100. For more information, see Wiring on page C-

Chain Port Output

The chain port output provides an EIA-232 output to chain control to

other TSUs. For more information, see Wiring on page C-1.

61202076L1-1

TSU 600 User Manual

2-9

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 2. Installation

10BaseT Interface (600e only)

The 10BaseT interface provides the LAN interface for managing the TSU

600e with SNMP or T-watch PRO. For more information, see Wiring on

page C-1.

Option Slot Arrangement

As viewed from the rear of the TSU 600, the slots are numbered as

shown in Figure 2-3. All slots are functionally identical except slots one,

two, and six. These slots offer additional functions.

SLOT 1

SLOT 4

SLOT 5

SLOT 6

DTE TIMING

SLOT 2

DIAL BACKUP

SLOT 3

SECONDARY INTERFACE

DSX-1; FULL D&I

TSU 600 Slot Designation (Rear View)

Figure 2-3.

Slot 1

Slot 1 is used as the source of DTE timing when the

DTE timing mode is selected or as the source of

UBR1TE timing when the UBR1TE timing mode is

selected. If DTE timing is desired, the DTE interface

port sourcing the timing must be connected to Slot 1.

This slot will accept all other interface types except

Secondary Network interface option modules, includ-

ing DSX-1 (PBX), the Full Drop and Insert (D&I) net-

work interface, or the multiport Dial Backup (DBU).

Slot 2

Slot 2 is used for the multiport Dial Backup module if

it is installed. This slot accepts all other interface

types except Secondary Network interface option

modules, including DSX-1 (PBX) and the Full Drop

and Insert (D&I) network interface.

2-10

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 2. Installation

Slots 3-5

Slot 6

Slots 3-5 will accept any interface type except second-

ary interface, the interface for DTE timing, or the mul-

tiport DBU. If other interfaces have any restriction on

their location, this will be specified in the individual

option card manual (provided with the option cards).

Slot 6 services any option module type including sec-

ondary network interface ports (DSX-1 (PBX) and Full

D&I), but not the DTE timing source. If a secondary

network interface port is to be used, it must be

installed in slot 6.

You can use NxDBU modules in any slot.

Power-up Testing

When shipped from the factory, the TSU 600 is set to factory default con-

ditions. At the first application of power, the unit automatically exe-

cutes a memory self-test. A full self-test can be run from the front panel,

and a passcode and unit ID may be set using the UTIL menu.

Self-Test

Upon a power-up, the LCD displays Memory Test Now Testing and the

Test LEDs are illuminated.

When . . .

Then . . .

the self-test is complete

with no failures detected

the OK LED lights up and the LCD

momentarily displays All Tests

Passed.

a failure is detected

a list of failures is displayed in the

LCD window

61202076L1-1

TSU 600 User Manual

2-11

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 2. Installation

The full self-test procedure (invoked from the front panel or

T-Watch PRO) consists of the following tests:

Board level tests

Each of the TSU 600 boards contains an on-board processor which exe-

cutes a series of tests checking the circuitry on the board.

• RAM and EPROM tests

• Verify on-board circuitry

Unit level tests

• Front panel LED verification

• Board-to-board interface test

A test pattern is sent from the controller through a loopback on all other

boards and checked on the controller. This verifies the data path, clocks,

and control signals for the entire chassis.

Initialization

Set User Passcode

The TSU 600 is designed to operate with or without the use of a pass-

code. The default condition is without a passcode.

If the unit is to be remotely accessed using T-Watch PRO, you must enter

a passcode. When managing a number of units, the passcode can be the

same for all the units.

The passcode should be a number easily remembered. Once entered,

the passcode is required to access any operation other than viewing. See

Set Passcode on page 6-2.

Set Unit Identification

The Unit ID sets the unit to respond to remote control (controlled by a

device other than the front panel or terminal). If no Unit ID is recorded

it is not possible to operate from any remote control device, including

the local PC for T-Watch PRO or SNMP. See Unit ID on page 6-3 for de-

tails.

2-12

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 2. Installation

Set Control Port

The TSU 600 can be configured from the control port when T-Watch

PRO, SNMP, or the terminal interface is being used.

If the control port is to be used, the control port baud rate must also be

selected.

Chain-In (PC)

The unit can be controlled from an external PC connected directly or via

modem to the Chain-In port. When using Chain-In, the selection of the

Control Port baud rate from 9600 (factory default), 1200, 2400, or 4800,

19200, or 38400 must be made using the Unit Configuration menu. Un-

less locked out externally, the front panel can also control the unit.

Chain In/Chain Out

TSU 600 units and other TSUs can be linked together to form a chain.

Figure 2-4 provides an example of a chain-in arrangement with a PC or

a modem. The first TSU 600 in the chain receives controlling input from

the PC or modem.

PC or Modem

Chain

Out

Control

Input

Chain

Out

Chain

Out

TSU 600/

TSU 100/TSU

TSU 600

TSU 600/

TSU 100/TSU

Example of Chain In

Figure 2-4.

Subsequent TSUs in the chain are in a position to intake information

from another TSU. This in-taking of information from another TSU in

the chain is identified as Chain-In. The baud rate for the chained units

must match that of the first unit.

Unless locked out externally, the front panel can also control the unit.

At this point, the Unit Initialization procedure is concluded. If the unit

is to be configured remotely, there are no additional items necessary to

complete prior to executing remote configuration.

61202076L1-1

TSU 600 User Manual

2-13

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 2. Installation

The Passcode, the Unit ID, and the Control Port settings are stored in a

nonvolatile memory. This ensures that they are operable for subsequent

power-up sequences.

Normal Power-Up Procedure

After the unit has been put into operation with the initial power-up and

initialization, subsequent power-up procedure includes only the Power-

Up Self-Test followed by the request for a passcode (password) if this

option was selected during initialization.

Use the number keys to key in the previously recorded passcode and

press Enter.

2-14

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Chapter 3

FRONT PANEL

The TSU 600 front panel both monitors operation and controls the con-

figuration of the unit. The TSU 600 front panel is shown in Figure 3-1 on

page 3-4. Descriptions of each part of the front panel follow.

Name

Description

LCD Window

Displays menu items and messages in two lines by

16 characters. It also displays alarm and status

information.

Enter

Selects active menu items. To select a menu item,

press the number of the item. The menu item

flashes, indicating it is activated. Press Enter to

select the menu item.

Up and down

arrows

Up and down arrows are used to scroll through

and activate the submenu items available in the

current menu. When the submenu items are

scrolled, the flashing cursor indicates the active

parameters.

Cancel

Pressing the Cancel key stops the current activity

and returns the display to the previous menu.

Repeat until the desired menu level is reached.

When a submenu item is displayed, press Cancel

to exit the current display and return to the previ-

ous menu.

Numeric Keypad The numeric keypad contains the numbers 0

through 9 which are used to activate menu items

and enter information (such as the IP address).

61202076L1-1

TSU 600 User Manual

3-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 3. Operation

Name

Description

Shift

To enter special function keys, press and release

Shift before pressing the key representing the

desired character. See Operation Keys on page 3-5

for a description of the function keys.

To activate a special function key rather than a

number, press Shift and then the key. If you press

the key without using Shift, the numbered item

becomes active instead of the special function key.

CSU Status LEDs

The CSU status LEDs display the operational condition of the network

interface located on the controller board in the unit.

Name

Description

OK (green)

Indicates the operation is in the normal mode and no

errors have been detected.

Test (yellow) Indicates that the network interfaces are operating in a

test mode. This includes a self-test or a test loopback.

When lighted, this LED also indicates that normal data

flow is not occurring on the network interface.

Error (red)

Indicates an error such as a BPV, OOF, or CRC.

Alarm (red)

Indicates an alarm condition has been detected. When the

alarm condition is no longer valid, the OK LED activates

(turns on).

To view an alarm condition, select the active alarm menu

item or select Alarm by pressing Shift 8.

If the alarm conditions have been corrected, the alarm

which caused the activation of the Alarm LED can be

viewed under the Unit History menu.

3-2

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 3. Operation

Module Status LEDs

The module status LEDs display the operational condition of ports in-

stalled in the option slots.

Name

OK (green)

Description

Indicates the operation is in the normal mode

and no errors have been detected.

Test (yellow)

Indicates that one of the interfaces is operat-

ing in a test mode. This includes a self-test or

a test loopback. When lighted, this LED also

indicates that normal data flow is not occur-

ring in at least one of the module ports.

Alarm (red)

Indicates an alarm condition has been

detected. When the alarm condition is no

longer valid, the OK LED activates (turns on).

To view an alarm condition, select the active

alarm menu item or select Alarm by pressing

shift 8. If the alarm conditions have been cor-

rected, the alarm which caused the activation

of the Alarm LED can be viewed under the

Unit History menu.

System (green)

Indicates the status of the power supplies.

If the LED is illuminated green, all installed

power supplies are functioning properly.

If the LED is illuminated red, one or both

power supplies are not functioning normally.

This feature is for the AC-powered 600e only.

For the TSU 600 and DC- powered 600e, the

system LED is always green.

61202076L1-1

TSU 600 User Manual

3-3

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 3. Operation

TSU 600

ENTER

ALARM

CLEAR

TEST

COPY

HOME

SHIFT

ALARM

CANCEL

SYSTEM

CSU

TEST

ERROR

ALARM

1. LCD Window

2. Cancel

3. Enter

Displays menu items and messages in 2 lines by 16 characters.

Stops current activity and returns to the previous menu.

Selects active menu item

4. Copy

Copies last data entered into the current DS0.

Returns to the main menu.

5. Home

6. Alarm

7. Clear

Quick access to the active alarm display menus.

Clears data/results fields

8. Shift

Provides access to special function keys

Active when an alarm condition has been detected.

Active when the module is in test mode.

Operation is in normal mode with no detected errors.

Indicates status of power supplies (600e only)

9. Alarm (Module Status)

10. Test (Module Status)

11. OK (Module Status)

12. System LED

13. Up and Down Arrows

Scroll through and activate the submenu items available in the

current menu. The flashing cursor indicates the active parame-

ter.

14. OK (CSU Status)

15. Test (CSU Status)

16. Error (CSU Status)

17. Alarm (CSU Status)

Operation is in normal mode with no detected errors.

Active when the network interface is in test mode.

Indicates errors such as BPV, OOF, and CRC.

Active when an alarm condition has been detected on the net-

work interface.

TSU 600 Front Panel Layout

Figure 3-1.

3-4

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 3. Operation

Operation Keys

Name

Description

Used in the DS0 mapping menu operations to copy

Copy

the last data entered into the current DS0. This key

operates without pressing the Shift key.

Home

Alarm

Returns home to the Main Menu from any menu

location.

Used as quick access to the active alarm display

menus. This can be activated while any other menu

item is in use. When the Alarm Menu is exited, the

unit returns to the location of the same menu that

was active when Alarm was selected.

Clear

Used in various menus to clear data/result fields.

General Menu Operation

The TSU 600 uses a multilevel menu structure containing both menu

items and data fields. All menu operations and data are displayed in the

LCD window. The menu items are numbered and can be viewed by

scrolling with the up and down arrows.

Name

Description

Data Field

You can edit menu items followed by a colon (:)

DisplayOnly You cannot edit menu fields followed by an

Field

equal symbol (=). This symbol identifies a field

used for value display only

Arrows

Menus that display small up or down arrows in

the lower right corner indicate there are more

menu items than are visible on a two-line LCD.

Access the additional items with the up or

down arrows. You can also access undisplayed

menu items by using the appropriate menu

number.

61202076L1-1

TSU 600 User Manual

3-5

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 3. Operation

Selecting and Activating a Menu Item

Step

Action

Choose a menu item by placing the cursor on the desired

menu item by either:

1. pressing the number corresponding to the menu item or,

2. highlighting it with the up and down arrows.

To activate the Alarm List option from the Status Menu

do the following:

1. Activate the Status Menu using the arrow keys or by

pressing 1. The cursor will flash on the number next to

the activated selection.

2. Press Enter.

3. Use the arrow keys to view submenu items.

4. Choose an item on the submenu such as ACTIVE

ALARMS.

5. Select the submenu with the arrow keys or by pressing

6. Press Enter.

7. View the Alarm List using the arrow keys.

The front panel menu tree is shown below.

1) NI PERF RPTS

2) NI ERRORS

3) ACTIVE ALARMS

4)VIEW HISTORY

(ALARM LIST)

END OF LIST

1)STATUS

5) PORT STATUS

6) REMOTE PORT

7) CLEAR PORT ALM

8) ENET STATUS

9) PS STATUS

Example of Basic Front Panel Menu Travel

Figure 3-2.

3-6

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 3. Operation

Editing the Data Field

Use the following steps to edit data fields preceded by a colon (:).

Step

Action

Result

Position the cursor on the The cursor moves to the data field

submenu item number

(to the right of the submenu item

name).

and press Enter.

Using the arrows, scroll to The value settings display one-at-a-

scan the available value

settings.

time in the data field position.

When the desired value is When the value is set, the cursor

displayed, press Enter to moves back to the submenu item

set that value.

position, indicating the operation is

complete.

Select another submenu

field or press Cancel to

return to the submenu.

Pressing Cancel before pressing

Enter voids any data changes. The

original data value is restored and

the cursor returns to the submenu

field.

61202076L1-1

TSU 600 User Manual

3-7

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 3. Operation

Display Only Data Fields

Data fields preceded by an equal (=) symbol cannot be edited. See Figure

3-3 and the instructions listed below.

Data Field

Display Field

Display and Data Fields

Figure 3-3.

Step

Action

Press Enter to move the cursor to the data field.

Use arrows to select AUTO and press Enter.

• The unit automatically sets the Line Build Out.

• The display field shows the value actually set.

• The equal symbol after LBO in the second line in-

dicates the information that follows is displayed

data and cannot be edited.

Exit Any Menu Field Operation Or Display

Press Cancel as many times as required to return to the desired menu

level or press Home to return to the main menu.

3-8

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 3. Operation

Data Port Identification

When configuring the unit, menu selections will include options from

data port submenus. Selecting of data ports is necessary because the

TSU 600 uses a Slot-Port method to identify which data port the menu

item is referencing. If a module containing a PBX DSX-1 option card

with an Nx56/64 plug-on interface is installed in option slot 6, it would

be designated as:

DSX-1 Passthru=6.1

Where slot=6 and port =1.

The DSX-1 is located in option slot 6 and is the first port in that slot.

Nx56/64=6.2

Where slot=6 and port=2.

The Nx is located in Slot 6 and is the second port in that slot.

Viewed from the rear of the TSU 600, the module slots are arranged as

shown in Figure 3-4.

SLOT 1

SLOT 2

SLOT 3

SLOT 4

SLOT 5

SLOT 6

Module Slots, TSU 600

Figure 3-4.

61202076L1-1

TSU 600 User Manual

3-9

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 3. Operation

Front Panel Menu Structure

The TSU 600 uses a multilevel menu structure containing both menu

items and data fields. All menu operations and data display in the LCD

window.

The opening menu is the access point to all other operations. Each Main

Menu item has several functions and submenus to identify and access

specific parameters.

The front panel LCD of the Main Menu contains the following options:

Option

Status

Description

Displays all relevant information for the network

and DTE interfaces. For detailed information on

status options, see Chapter 4, Status Menu.

Config

Displays and sets the TSU 600 operational config-

(Configuration) uration, including all network interface parame-

ters, the allocation of the DS0s, and the port

parameters.

For detailed information on configuration options,

see Chapter 5, Configuration Menu.

Util (Utilities)

Test

Displays and sets system parameters. For detailed

information on utility options, see Chapter 6, Util-

ity Menu.

The Test menu initiates different types of unit tests

and displays test results in the LCD window. For

detailed information on test options, see Chapter 7,

Test Menu.

3-10

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 3. Operation

Alternate Methods of Control

T-Watch PRO (ADTRAN PC Program)

T-Watch PRO is the ADTRAN PC control program. It provides complete

control over the configuration of the TSU 600 using a graphical interface

and displays the same status and performance data as the front panel

LCD. This data is displayed in the form of tables and graphs.

The T-Watch PRO program has the following capabilities:

• Interfaces with a modem which permits dialing into a remote TSU

600 location to configure the unit or read the status or performance of

the unit.

• Receives traps from any TSU product.

• Records and creates display performance data over a 30 day period.

• Accesses units via the local area network.

T-Watch PRO/LAN Connection

To set up the TSU 600 to work with T-Watch PRO over the LAN, follow

these steps:

Step

Action

Set the Unit ID using the Front Panel.

See Unit ID on page 6-3 for more information.

Set Control Port to SLIP or Normal for 10BaseT (600e

only) using the Front Panel.

Configure the IP address default gateway, and sub-

net mask using the Front Panel.

The default gateway and subnet masks are not used

for SLIP mode.

Follow the installation instructions for T-Watch PRO

to start the program and connect to the unit.

61202076L1-1

TSU 600 User Manual

3-11

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 3. Operation

T-Watch PRO/EIA-232 Connection

To set up the TSU 600 to work with T-Watch PRO over a direct EIA-232

connection, the following steps are required:

Step

Action

Set the Unit ID and the Passcode using the Front Panel.

See Unit ID on page 6-3 and Change/Set a Passcode on page

6-3 for more details.

Set the Control Port rate to the same setting as the PC

Com port.

Connect the PC Com port to the Chain-In port on the

TSU 600 using the DB25 to modular adapter and 6-foot

modular cable.

Follow the installation instructions for T-Watch PRO to

start the program and connect to the unit.

SNMP

The ADTRAN TSU 600 supports the Simple Network Management Pro-

tocol (SNMP) through the chain-in (SLIP) interface or 10BaseT interface

(600e only). See Appendix B, Understanding SNMP for detailed informa-

tion.

To use SNMP with the TSU 600, do the following:

Step

Action

Set Control Port to SLIP for Chain-In Port or Normal for 10BaseT

(600e only).

Set the IP address, default gateway, and subnet mask through the

front panel.

The default gateway and subnet mask are not used in SLIP mode.

Load the appropriate MIB browser into the Network Management

Station (available on the ADTRAN webpage at http://www.adt-

ran.com). The MIB browser issues SNMP gets/sets to the TSU 600.

3-12

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 3. Operation

Terminal Mode Connection

The TSU 600 provides the front panel menus to a VT-100 type terminal.

This mode can be used to configure and monitor the unit. Initiate this

mode by typing <ctrl> PTT on the terminal once it is connected to the

Chain-In port. For detailed information on this method of control, see

Telnet Terminal Menus on page 8-1.

Telnet Connection

You can connect to the TSU 600 via telnet. Before attempting to connect

via telnet, first define the IP address, the default gateway, and subnet

mask using the front panel.

The dafault gateway and subnet mask are not used in SLIP mode.

When you begin the Telnet session, you will be prompted for a pass-

word. The default password is ADTRAN. You can change this pass-

word using the Management submenu. See Default Unit Passcode on

page 8-7, for details. The telnet session will time-out after a predefined

value that is also set in the Management Menu.

Only one telnet session can be active at one time.

61202076L1-1

TSU 600 User Manual

3-13

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 3. Operation

3-14

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Status Menu

Chapter 4

The Status menu branch allows you to view the status of the TSU 600 op-

eration. See Figure 4-1.

%AS

%EF

1) NI PERF RPTS

2) NI ERRORS

SES

UAS

1)STATUS

3) ACTIVE ALARMS

4)VIEW HISTORY

(ALARM LIST)

END OF LIST

(HISTORY LIST)

END OF HISTORY

5) PORT STATUS

6) REMOTE PORT

7) CLEAR PORT ALM

8) ENET STATUS

9) PS STATUS

OPTION LIST

Complete Status Menu

Figure 4-1.

61202076L1-1

TSU 600 User Manual

4-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 4. Status Menu

Menu flow is normally depicted from left to right. Arrows on the lower

right of the screen indicate the direction of scrolling to use to view addi-

tional menu items. At every level of the menu, pressing Cancel returns

the system to the previous menu level. Press Cancel repeatedly to return

the system to the main menu.

Network Performance Reports (NI PERF RPTS)

The Network Interface Performance Reports display the user copy of the

performance data. See Figure 4-2. The TSU 600 maintains this perfor-

mance data on the network in compliance with ANSI T1.403 and AT&T

document TR54016. The data displayed is data accumulated over the

last 15 minutes and over the last 24 hours.

Use the scroll keys to access the complete display of the following report

fields:

15 Minutes

24 Hours

Data Values

%AS

%EF

% of available seconds

% of error free seconds

Number of errored seconds (1 or more

errors/second

SES

Number of severely errored seconds

(more than 320 errors/second)

UAS

Number of unavailable seconds (10 or

more consecutive seconds)

Network Interface Performance Report

Figure 4-2.

4-2

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 4. Status Menu

If insufficient time has passed to collect data, NA displays. Continue

with standard operating procedures to exit the display.

When this menu is active, performance data can be cleared by pressing

Clear (Shift 9) on the keypad. Only the user copy of the performance

data is cleared.

Since only the user’s copy of performance data is cleared by the TSU 600,

the data displayed here might be different from the data sent to the net-

work as PRM data.

Network Interface Errors (NI ERRORS)

The NI Errors submenu displays the types of errors the Network Inter-

face (NI) detects. A blinking CSU error LED indicates that network er-

rors are detected.

The asterisk (*) above an item indicates the type of errors detected. The

error types are as follows:

CRC

CRC-6 bit errors based on the FDL.

This is valid only in ESF mode.

BPV

XS0

FER

Bipolar violations.

Excess zeros.

Framing errors.

61202076L1-1

TSU 600 User Manual

4-3

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 4. Status Menu

Active Alarms

This menu item displays a list of current alarms reported by either the

base controller or any of the ports. If no alarms are current, the menu

item displays End of List. See Figure 4-3.

This display includes two lines of text. The top line is the alarm source.

The bottom line is the alarm message. A list of alarm messages is found

in Appendix C, System Messages, on page C-1.

In addition to normal menu operation, you can also access this menu

item with the Alarm function (Shift 8) on the keypad. If one or more of

the Alarm LEDs are illuminated, an alarm is present. Press Cancel to re-

turn to the previous menu item.

Alarm Source

Alarm

Message

Display of Alarm Messages

Figure 4-3.

View History

This menu item displays and clears the accumulated status changes of

the unit.

View History displays a history of the first 20 status changes in the unit,

including the date, time, and type of change. The unit also records for

viewing the date and time an alarm became active and inactive, as well

as the date and time of test activation and deactivation.

To clear the View History display, press Clear (Shift 9) with the View

History menu active.

4-4

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 4. Status Menu

Port Status

Port Status displays the signals monitored on the data ports. For exam-

ple, an Nx56/64 interface monitors the RTS, CTS, TD, and RD, along

with other signal lines. When a port is selected, the LCD indicates

whether the signal is present.

Remote Port

Remote Port displays the status of activity on the Chain-In remote port.

This is useful for troubleshooting communication sessions, as well as

verifying cabling.

RX Characters received at remote port.

ID Unit ID received at remote port.

CRC Correct CRC received.

PC Correct passcode received.

TX Characters transmitted from the remote port.

Clear Port Alarm

Clears the Link Failed alarms on option modules that have been re-

moved from the TSU 600 chassis.

61202076L1-1

TSU 600 User Manual

4-5

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 4. Status Menu

ENET Status (600e only)

Indicates that data is being transmitted from the 10BaseT port

RX Indicates that data is being received by the 10BaseT port

LNK Indicates the current status of the 10BaseT link integrity test.

This should always be on when the unit is connected to a

functional 10BaseT hub.

CPU Active when the CPE is accessing the 10BaseT interface.

PS Status (600e only)

Displays the status of Power Supply A (PSA) and Power Supply B (PSB)

for AC powered units. Displays DC supply for DC Powered units.

Possible status: NOT PRESENT, INACTIVE, OK, DC Supply (DC units

only)

4-6

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Configuration Menu

Chapter 5

The Configuration menu sets the TSU 600 operational configuration, in-

cluding all network interface parameters, the allocation of the DS0s, and

the port parameters. See Figure 5-1.

1) FORMAT

1) CTL PORT RATE

2) TRAPS

2) CODE

3) YEL ALARM

4) XMIT PRM

3) ACCESS

4) INIT MODEM

5) CONTROL PORT

6) IP ADDRESS

7) SUBNET MASK

8) DEFAULT ROUTER

9) SLIP RATE

1) NETWORK (NI)

5) TIMING MODE

6) SET LBO

7) INBAND LPBCK

8) BIT STUFFING

9)TR-08 OPTIONS

A) ALARM REPORT

B) ALARM FORMAT

C) BPV THRESHOLD

A) SLIP FLOW CTL

B) PROXY TRAPS

2) UNIT

3) MAP XCHNG

4) MAP IN USE: A(B)

OFF

AUTO

1) MAP A @: HH:MM

2) MAP B @: HH:MM

1) COPY A>TEMP

2) CREATE TEMP

3) REVIEW MAP A

4) REVIEW TEMP

5) EDIT TEMP

2) CONFIG 5)DS0 MAP A

1) COPY B > TEMP

2) CREATE TEMP

3) REVIEW MAP B

4) REVIEW TEMP

5) EDIT TEMP

6) DS0 MAP B

6) APPLY TEMP > A

6) APPLY TEMP > B

7) PORT CONFIG

(OPTION PORTS)

Configuration Menu

Figure 5-1.

61202076L1-1

TSU 600 User Manual

5-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 5. Configuration Menu

Menu flow is normally depicted from left to right. Arrows on the lower

right of the screen indicate the direction of scrolling to view additional

menu items. At every level of the menu, pressing Cancel returns the sys-

tem to the previous menu level. Pressing Cancel repeatedly returns the

system to the Main menu.

NETWORK (NI)

This menu item accesses the configuration of parameters associated

with the network interface in the base unit. There are nine submenu

items that include setting the format, the Line Build Out (LBO), and the

timing mode. Submenu items do not include setting the parameters

which may be necessary for a secondary interface (DSX-1 Passthru, etc.).

Network (NI) Menu Items

The menu items and their descriptions follow.

Format

Sets the frame format for the NI.

Choices: D4, ESF, SLC96

D4 is equivalent to superframe format (SF).

Code

Sets the line code for the NI.

Choices: AMI, B8ZS.

YEL Alarm

Enables and disables the transmitting of yellow

alarms.

Choices: ENA, DISA

XMIT PRM

Enables and disables the sending of PRM data on

the facility data link (FDL).

The PRM data continues to be collected even if

XMIT PRM is disabled (possible only with ESF

Format).

Choices: Off, On.

Timing Mode

Selects the clock source for transmission toward

the network from the NI. See TSU 600 Clock

Sources on page 5-4 for more information.

Choices: Network, DTE (Slot 1), Normal (CSU),

U-BR1TE (Slot 1), Internal, and Secondary (SI).

5-2

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 5. Configuration Menu

SET LBO

Selects the line build out for the network interface.

In AUTO mode, the TSU 600 sets the LBO based

on the strength of the receive signal and displays

the selected value.

Choices: 0.0 dB, 7.5 dB, 15 dB, 22 dB, and Auto

To activate the -36 dB receiver sensitivity, set

the LBO to AUTO. This feature is useful in a

point-to-point application where no network

elements are involved. If a network element

such as a Smart Jack is installed on the circuit,

the LBO should be set to 0 dB.

INBAND

LPBCK

Sets unit to accept or reject the network interface

loop-up and loop-down codes as defined in ANSI

T1.403.

Choices: Accept, Reject

BIT STUFFING When enabled, bit stuffing causes the TSU 600 to

monitor for ones (1s) density violations and insert

a one (1) when needed to maintain ones at 12.5%.

Choices: Enable, Disable

TR-08

The TR-08 submenu configures the unit for TR-08

applications. The submenu items and their

descriptions follow.

Alarm Report

Enables and disables the transmitting of alarm

reports.

Choices: SEND ALARMS, DISABLE ALARMS

Alarm Format

Sets the alarm frame format to 13 frames or 16

frames.

Choices: ORB-13, ORB-16

BPV Threshold

Sets the threshold for BPVs to trigger an alarm.

Choices: 10-4, 10-5, 10-6

61202076L1-1

TSU 600 User Manual

5-3

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 5. Configuration Menu

TSU 600 Clock Sources

The TSU 600 is operable from various clock sources, permitting it to per-

form properly in many different applications. The network interface

timing mode is set by using the Network (NI) Configuration menu op-

tions. The following options are available:

• Network Timing

• DTE Timing

• UBR1TE

• Internal Timing

• Secondary Timing

• Normal (CSU) Timing

The selected clock option always designates the clock source for trans-

mission. Clocking necessary for receiving data is always recovered from

incoming data.

Network Timing

The network is the source of timing. The received data clocking is

looped back to the network, where it is used to determine the transmis-

sion timing. This option is also referred to as loop timed as the transmis-

sion clock is derived from the received clock. See Figure 5-2.

NETWORK

INTERFACE

SECONDARY

INTERFACE

TIMING SOURCE

OPTION SLOTS

Network Timed Clock Source

Figure 5-2.

5-4

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 5. Configuration Menu

DTE Timing

The DTE is the source of timing. The TSU 600 uses the incoming DTE

clock to determine the transmission timing. This is typically used in ap-

plications where it is necessary to have the DTE as the primary clock

source (such as limited distance line drivers). See Figure 5-3.

The DTE source timing is restricted from use when a secondary interface

is used at the same time.

Clock

NETWORK

INTERFACE

OPTION SLOTS

TIMING SOURCE

DTE

DTE Timed Clock Source

Figure 5-3.

U-BR1TE (Slot 1)

The timing mode selection U-BR1TE (Slot 1) works much like DTE tim-

ing except that the clock is derived from the U interface.

61202076L1-1

TSU 600 User Manual

5-5

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 5. Configuration Menu

Internal Timing

The TSU 600 is the source of timing. The TSU 600 is configured to use its

own internal oscillator as the source of timing. Applications include pri-

vate line driver circuits where one end is set to network and the other to

internal. See Figure 5-4.

NETWORK

INTERFACE

SECONDARY

INTERFACE

(Option)

OSC

OPTION SLOTS

TIMING SOURCE

Internal Clock Source

Figure 5-4.

5-6

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 5. Configuration Menu

Secondary Timing

The secondary interface is the source of timing. The TSU 600 uses the

clock derived by the secondary interface for transmission timing. See

Figure 5-5.

NETWORK

INTERFACE

SECONDARY

INTERFACE

(Option)

OSC

OPTION SLOTS

TIMING SOURCE

PBX or

Second Network

Secondary Clock Source

Figure 5-5.

61202076L1-1

TSU 600 User Manual

5-7

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 5. Configuration Menu

Normal (CSU) Timing

The typical timing option arrangement is shown in Figure 5-6. The PBX

is looped timed to the TSU 600. The Network Interface (NI) is the actual

source of timing. This timing option is the same as that typically used for

CSUs. This is the preferred mode for use with a PBX application.

NETWORK

INTERFACE

SECONDARY

INTERFACE

(Option)

TIMING SOURCE

OSC

OPTION SLOTS

PBX or

Second Network

Normal (CSU)

Figure 5-6.

5-8

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 5. Configuration Menu

Unit Menu

The Unit menu changes the baud rate of the Chain-In port and the setup

of the Chain-Out port. The menu items are:

Ctl Port

Rate

Sets the baud rate for communication with the

PC or modem.

Choices: 1200, 2400, 9600, 19200 and 38400 kbps

Traps

Enables or disables the transmission of trap mes-

sages.

Choices: Enable, Disable

Access

Sets the method of connection from the TSU 600

to T-Watch PRO/SNMP.

Choices:

Direct - Used if connected directly to the PC

Dial - Used when connection is through a

modem. The dial string is entered from T-Watch

PRO/SNMP.

Init Modem Allows you to choose an industry standard or a

custom initialization string for a modem con-

nected to the control port.

Control Port Selects the TCP/IP physical interface.

Choices: SLIP using the EIA-232 serial port or

10BaseT Ethernet (600e only).

If this option is set to SLIP, the Chain-In port

may not be used as a terminal interface.

IP Address Uniquely identifies the TSU 600 on a TCP/IP

network. This address is composed of four deci-

mal numbers, each in the range of 0 to 255, sepa-

rated by periods.

61202076L1-1

TSU 600 User Manual

5-9

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 5. Configuration Menu

Subnet

Mask

Defines which part of a destination IP address is

the network number. Used along with the TSU

600e IP address to determine which nodes must

be reached through the default IP Gateway.

This value is set to 0.0.0.0 when the IP interface

option is set to SLIP.

Default

Router

All IP Packets destined for nodes not on the TSU

600e unit’s local network are not forwarded

through this IP address. Normally, this address

defines a router connected to the TSU 600e unit’s

local network. This value is ignored when the IP

interface is set to SLIP.

SLIP Rate

Sets the baud rate for the Chain-In port when

used as the SLIP connection for SNMP manage-

ment.

Choices: 1200, 2400, 4800, 9600, 19200, 38400

SLIP Flow Used to activate flow control on the Chain-In

CTL

port when used as the SLIP interface. Hardware

mode uses RTS and CTS.

Choices: None, Hardware

Proxy Traps Enables or disables the transmission of trap mes-

sages from units being "proxied" for.

Choices: Enable, Disable

5-10

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 5. Configuration Menu

Map Exchange (Map Xchng) Menu

The Map Exchange menu enables and sets the automatic time-of- day

map switch. The unit provides selection of the hour, minute, and sec-

onds for the map switching to take place.

The menu items are:

OFF

Indicates the map in use does not change (disabled).

Off disables the Automatic Map Change feature.

Press Enter to activate the selection.

AUTO

Indicates that the map in use will change at a user-

selected time of day.

AUTO enables the Automatic Map Change feature.

Press Enter to activate the selection

When Auto is selected, the unit displays the screens

to set times for switching. After editing Map A,

press Enter to record the Map A settings and activate

the selection fields for Map B. Use the same opera-

tion to edit switching time for Map B.

When ESF is used with an FDL channel between

units, the units automatically coordinate the auto-

matic map switch by sending a map switch com-

mand from end-to-end over the FDL. Only one end

needs to be set to Auto for this to work.

MAP In Use: A(B) Menu

This menu item controls the DS0 map the TSU 600 uses and displays the

map in current use.

61202076L1-1

TSU 600 User Manual

5-11

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 5. Configuration Menu

DS0 Map A and DS0 Map B Menu

The DS0 maps designate which DS0s are assigned to which port. See

Figure 5-7. There are three maps: DS0 Map A, DS0 Map B, and the Tem-

porary (Temp) map.

T E M P

D S 0 A

D S 0 B

DS0 Map Designations

Figure 5-7.

DS0 A and DS0 B are the current maps the TSU 600 uses.

The Temp Map generates a map before putting it into use.

You can copy DS0 A to DS0 B by copying the DS0 A map into the Temp

map. Then apply (write) the Temp map into DS0 B.

The menu items are:

COPY A >TEMP

Copies the current map (A or B) into a

Temp map area.

Permits modification without disturbing

the existing map. When the modifications

are completed, the Temp map is written to

current MAP A (B) by selecting Apply.

CREATE TEMP

Creates a map by defining a port or Idle for

all DS0s.

When CREATE TEMP is first selected, all

DS0s are set to Idle. See Create Temp Exam-

ple on page 5-13 for more information.

5-12

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 5. Configuration Menu

REVIEW MAP

A(B)

Permits a quick review of the number of

DS0s assigned to each port and the number

of unassigned DS0s (Idle or TST) as defined

in the currently applied Map A(B).

REVIEW TEMP

EDIT TEMP

This menu item is operated the same for

the Temp map as is 3)REVIEW MAP A or

Map B.

The map in the Temp file can be edited to

whatever configuration is desired. If Map

A had been copied into the Temp file, then

after editing, the Temp file could be

applied to MAP A or MAP B. The menu

operation is identical to 2) CREATE TEMP

with the exception that the existing port

selections display.

APPLY TEMP > A Writes the Temp map into Map A. Pressing

Apply is usually the last step in updating a

map and is accessed automatically at the

end of editing or creating a temporary

map. It can be bypassed at this time by

selecting another menu choice.

Create Temp Example

A sample selection follows for Create Temp:

DS0: 01 to 24

PORT: IDLE, TST, + option module ports

TST designates which DS0s are used for QRSS testing when activated

under the TEST Menu. When not used for testing, the TST designation

is identical to IDLE.

61202076L1-1

TSU 600 User Manual

5-13

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 5. Configuration Menu

1. With the cursor on CREATE TEMP, press Enter. The unit displays the

selection screen with the cursor positioned on the first selection DS0

number. See Figure 5-8.

Select DSO Number

Select Port

Create Temp Selection Screen

Figure 5-8.

2. Enter the DS0 number by using either the scroll method or numbers.

Do not mix the use of the keys.

3. Pressing Enter completes the selection and moves the cursor to PORT,

the next field.

4. Scroll to select the port which is dependent on the installed option

card.

5. Press Enter to complete the selection and move the cursor back to the

DS0 field.

With the cursor on the DS0 field, the DS0 number can be incremented or

decremented by scrolling. If you press Copy, the contents of the last DS0

entered are placed in the new DS0 number.

When all entries are complete, Cancel moves the cursor to the last of the

submenu choices, 6)APPLY. Either apply the newly created DS0 map or

press Cancel to return to the DS0 Map A (B) submenu choices.

Selecting Apply will not disrupt the operation of unmodified ports.

5-14

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 5. Configuration Menu

Port Configuration (Port Config)

Port Configuration selects and configures the parameters associated

with any data port in the unit. For example, parameters for the DSX-1

(PBX) interface are set through this menu. The items that can be set de-

pend on which option module is installed. The list of option ports will

vary with the configuration.

The TSU 600 is designed so that any additional ports developed in the

future will contain the appropriate menu selections to provide access by

use of this menu item.

The Config menus for options ports are described in separate sections of

the manual supplied with the option card.

61202076L1-1

TSU 600 User Manual

5-15

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 5. Configuration Menu

5-16

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Utility Menu

Chapter 6

The utility menu tree displays and sets system parameters. See Figure 6-

1. This includes setting the time and date, resetting all parameters to fac-

tory values, or re-initiating the unit. This menu also displays the unit

software revision and the Unit ID setting.

TIME: HH:MM:SS

1) TIME/DATE

DATE: MM/DD/YY

(Returns all configurations

to factory settings)

2) FACTORY RESTORE

3) SET PASSCODE

4) UNIT ID

NEW PASSCODE

3) UTIL

VERIFY PASSCODE

5) SOFTWARE REV

(Displays Current

Software Revision

6) PORT UTILITY

(OPTION PORTS)

7) ENET ADDRESS (600e only)

8) CMD MODE

Utility Menu Tree

Figure 6-1.

61202076L1-1

TSU 600 User Manual

6-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 6. Utility Menu

Menu flow is normally depicted from left to right. Arrows on the lower

right of the screen indicate the scrolling direction to view additional

menu items. At every level of the menu, press Cancel to return the sys-

tem to the previous menu level. Pressing Cancel repeatedly returns the

system to the Main menu.

Time/Date

This menu option displays or edits the current time and date. The TSU

600 maintains the time and date during power-off conditions.

If you want to...

Do this...

Record the entry and

move to the next editing

position

Press Enter after any numeric change

Move to a different field Press Enter at the editing position without

to edit

making any changes, or

Use the Up and Down Arrow keys

Press Cancel

End the editing process

Factory Restore

This menu item restores the factory default settings for all unit parame-

ters, including configured DS0 maps.

Set Passcode

Enter Passcode from Other Menus

The Passcode prompt may make an unexpected appearance from oth-

er menu operations. This happens only when the unit is operating in the

limited access mode, i.e., without an active passcode. The limited access

mode may become active even if a passcode was entered, as it does

when there is no activity for ten minutes. If the unit is to be remotely ac-

cessed using T-Watch PRO, a passcode must be entered. When manag-

ing a number of units, the passcode can be the same for all.

The unexpected appearance of the Passcode prompt occurs, for exam-

ple, while operating in a limited access mode and attempting to change

the data rate, (2)CONFIG, 2)UNIT, 1)CTL PORT RATE. Use the number

keys to enter the correct passcode and press Enter. The unit displays

Access Granted.

6-2

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 6. Utility Menu

Pressing any key after entering a passcode causes the unit to return to

the previous active menu. In this case it returns to 2)CONFIG, 2)UNIT,

1)CTL PORT RATE to permit changing the data rate.

Change/Set a Passcode

The passcode can be changed or set at any time or eliminated altogether

through the Utility menu item 3)SET PASSCODE. This procedure re-

quires the current passcode (if one is established) for operation.

The passcode can only be entered by using numbers. After entering the

desired passcode, press Enter.

Set a null passcode at the 3)SET PASSCODE menu by pressing Enter

without any numbers. This sets a null passcode and grants unlimited

access.

Automatic Time-out Feature

For added security protection, the unit is equipped with an automatic

time-out for operation with the password. After ten minutes of inactiv-

ity, the unit reverts to limited access operation. To make changes in the

configuration, the passcode can be reentered. See Set Passcode on page

6-2 for further information concerning passcode use, and both limited

and editing access.

If the passcode number is lost, contact ADTRAN Customer Service for

assistance.

No Passcode Desired

At the New Passcode prompt (in the Set Passcode menu), press Enter

without any numerical entry. The system nullifies the need to enter a

password for subsequent use and proceeds to the Unit ID prompt.

Unit ID

This menu is used to access the current Unit ID setting. Viewing is avail-

able in limited access mode. Editing or changing the Unit ID requires

the use of a password as in editing mode. Unit Identification numbers

must be between 2 and 999. If an out-of-range number is entered, the

unit assumes the upper limit number of 999.

61202076L1-1

TSU 600 User Manual

6-3

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 6. Utility Menu

Setting the Unit Identification

In the Unit ID menu (item 4) under the UTIL menu, enter any value be-

tween 2 and 999. The number 1 is reserved for the PC.

Pressing Enter records the Unit ID number and establishes its availabil-

ity for operation by remote control. The unit proceeds to the

Set Control Port prompt.

No Unit ID Desired

Without entering any numbers at the Unit ID prompt, press Enter.

Pressing Enter with no Unit ID recorded establishes the unit as unable

to be operated by remote control.

Software Revision (Software Rev)

This menu provides access to the display of the current software revi-

sion level loaded into the base unit controller. This information is re-

quired when requesting assistance from ADTRAN Customer Service or

when updates are needed.

Use Cancel to exit.

Port Utility

This menu provides access to the display of the current software infor-

mation for each port installed in the unit. This information is required

when requesting assistance from ADTRAN customer service or when

updates are needed.

ENET Address (600e only)

Displays the Ethernet MAC address for the 10BaseT port.

CMD Mode

Reserved for factory use.

6-4

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Test Menu

Chapter 7

The Test menu initiates different types of unit tests and displays test re-

sults in the LCD window. The Test menu contains four items. See Figure

7-1.

Executing tests will disrupt some of the normal operation. See individ-

ual menu items concerning tests before executing.

LINE ON

1) LOCAL LOOPBCK

2) REMOTE LOOPBK

PAYLOAD ON

NO LOOPBACK

ATT INBAND LLB

ANSI FDL PLB

ANSI FDL LLB

1) NETWORK TESTS

ANSI FT1 LLB

NO LOOPBACK

ALL ZEROS

QRSS ALL DS0S

QRSS TST DS0S

ALL ONES

4) TEST

3) TEST PATTERN

NONE

4) PATTERN RESULT

(Displays results)

(OPTION PORT)

(Displays results)

2) RUN SELFTEST

3) PORT TEST

4) CANCEL TESTS

Test Menu

Figure 7-1.

61202076L1-1

TSU 600 User Manual

7-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 7. Test Menu

Menu flow is normally depicted from left to right. Arrows on the lower

right of the screen indicate the scrolling direction to view additional

menu items. At every level of the menu, pressing Cancel returns the sys-

tem to the previous menu level. Pressing Cancel repeatedly returns the

system to the Main menu.

Network Tests

Network tests control the activation of loopbacks and the initiation of

data test patterns.

Network tests are run on the Network Interface (NI). You can select

three different test configurations to determine the type of loopback and

the pattern to run. Test results display in the LCD window.

Executing Network Tests will disrupt normal data flow unless only

TST DS0s are selected for testing.

Loopback Tests

A number of different loopbacks can be invoked locally from the front

panel, by T-Watch PRO commands, or remotely by using special in-

band codes (AT&T D4 network loop up and loop down codes). Addi-

tionally, the loopbacks can be remotely controlled by means of out-of-

band commands by the T1 ESF FDL or from T-Watch PRO by a modem

connection. See Figure 7-2.

7-2

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 7. Test Menu

Network Interface Loopbacks

Network interface loopbacks affect the entire T1 data stream. There are

two types of network loopbacks: line loopback and payload loopback.

Line loopback loops all of the received data back toward the network.

The transmitted data is the identical line code that was received, includ-

ing any bipolar violations or framing errors.

Payload loopback is similar to line loopback, except that the framing is

extracted from the received data and then regenerated for the transmit-

ted data.

TSU 600

NI CSU

Secondary

Interface

DS1

Payload Loopback

Line Loopback

Network Loopback Tests

Figure 7-2.

Local Loopbck

There are three available choices for setting the local loopback:

Name

Line On

Description

Activates the line loopback

Activates the payload loopback

Deactivates the loopback

Payload On

No Loopback

Scroll to select a setting and record it by pressing Enter. The unit returns

to the previous menu level.

61202076L1-1

TSU 600 User Manual

7-3

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 7. Test Menu

Remote Loopbk

This activates the same loopbacks as Local Loopback but at the far end.

It uses either the inband loopup code as specified by ANSI T1.403 for

line loopback (ATT In-Band LLB), or the FDL as specified in ANSI

T1.403 for payload and line loopback codes. The following options are

available:

Name

Description

ATT In-Band

LLB

Activates the line loopback using inband code

ANSI FDL PLB

ANSI FDL LLB

ANSI FT1 LLB

No Loopback

Initiates the transmission of an FDL payload

loopup code toward the far end

Initiates the transmission of an FDL line

loopup code toward the far end

Initiates the transmission of a FT1 loopback

using the inband code described in T1.403.

Deactivates the loopback

Remote Loopback can only be used with Fractional T1 if the ANSI FT1 LLB is

selected.

After a Remote Loopback option is selected, the TSU 600 verifies that the

far end is actually in a loopback by checking for the receipt of a code

looped back from the far end. Once the Remote Loopback type is select-

ed, the LCD displays the loopback progress by displaying Looping until

loopback is verified.

7-4

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 7. Test Menu

Test Pattern

Pattern

Description

All Ones

Sends an all ones pattern to the network

Sends an all zeros pattern to the network

All Zeros

QRSS All DS0s

Generates a QRSS test pattern and inserts

the pattern into all DS0s

QRSS TST DS0s

Inserts a QRSS pattern in those DS0s

mapped as TST in the currently active map

(A or B)

None

Terminates pattern generation

QRSS Pattern

The QRSS pattern is commonly used to simulate real data in T1 interfac-

es. This pattern can be assigned to appear in all DS0s or only in TST

DS0s. When QRSS is set in all DS0s and one of the network loopbacks

previously described is activated at the far end, a total end-to-end integ-

rity check can be run without the need for any external test equipment.

When QRSS is assigned to TST DS0s, an integrity check of the link can

be run along with normal data flow. The TST DS0s are user assigned as

part of the DS0 Map.

This sets the pattern for the test and initiates the transmission of the pat-

tern. The test is terminated by selecting None. The following patterns

are available:

QRSS always runs at 64K/DS0.

Example:

1. Use the up and down key to select QRSS ALL DS0s.

2. Press Enter to record the selection. The TSU 600 starts to generate a

QRSS test pattern and inserts the pattern into all DS0s.

3. Select None to end the test.

61202076L1-1

TSU 600 User Manual

7-5

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 7. Test Menu

Pattern Result

Displays the results of the test currently active. Leaving and returning to

this menu item does not interrupt the test.

Pressing 2 injects errors into the test pattern. These errors are detected

by the device performing the pattern check.

Pattern Description

The number of seconds with at least 1 bit error

BES

The number of seconds with more than 1 bit

error and less than 320

SES

The number of seconds with more than 320 bit

errors

SYNC

Indicates if pattern sync is (yes) or is not (no)

valid. An asterisk (*) indicates if pattern sync

has been lost since the start of testing

Clear results by pressing Shift 9. The results are accumulated until the

test pattern is set to None or Cleared.

Using TST DS0s for testing can be very useful, particularly in Fractional

T1 applications. You can run an end-to-end test on the Fractional DS0s

by:

Setting for Map B the TST in the same DS0 as used by Map A to

receive data from an Nx56/64 port, and

Looping the far end using a V.54 loopback code on the Nx56/64

port. In addition, a single DS0 can be used for continuous testing

while other DS0s are passing normal data.

This will also provide an end-to-end check on the entire link. Set each

end to send QRSS in TST DS0s (using 1 DS0) and occasionally view the

results on the Pattern Result Menu selection.

7-6

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 7. Test Menu

Run Self-Test

The self-test checks the integrity of the internal operation of the electron-

ic components by performing memory tests and by sending and verify-

ing data test patterns through all internal interfaces. Although actual

user data cannot be passed during these tests, the self-test can be run

with the network and DTE interfaces in place and will not disturb any

external interface.

The memory portion of the self-test automatically executes upon power-

up. A full self-test can be commanded from a front panel menu or from

T-Watch PRO.

In addition to the specified self-tests, background tests are run on vari-

ous parts of the internal electronics. These run during normal operation

to confirm continued correct functioning.

This menu selection is used to execute a full internal self-test. The results

of the self-tests are displayed in the LCD. Upon invoking the command,

the LCD displays System Self-Test and the Test LEDs are illuminated.

Test failures are displayed in the LCD window. The self-test consists of

the following tests:

Board level tests

Each of the TSU 600 boards contain an on- board processor which exe-

cutes a series of tests checking the circuitry on the board.

• RAM tests; EPROM checksum

• DS0 map tests

• On-board data path; sending a known test pattern through an on-

board loop

Unit level tests

• Front panel LED verification

• Phase Lock Loop verify

• Board-to-board interface test

A test pattern is sent from the controller through a loopback on all other

boards and is checked on the controller. This verifies the data path,

clocks, and control signals.

If a failure is detected, note the failure number and contact ADTRAN

Technical Support.

The execution of self-test will disrupt normal data flow and prevent re-

mote communication until the self-test is completed.

61202076L1-1

TSU 600 User Manual

7-7

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 7. Test Menu

Port Tests

The Port Tests menu is used to activate testing of specific data ports. It

controls the activation of loopbacks and the initiation of data test pat-

terns. Test results are displayed in the LCD window.

The execution of Port Tests will disrupt normal data flow in the port be-

ing tested.

Cancel Tests

Use this menu selection to deactivate all active tests, including tests on

option modules.

7-8

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Telnet/Terminal Menus

Chapter 8

MAIN MENU

The Telnet/Terminal Main Menu is the first menu displayed after the

telnet/terminal session is established. See Figure 8-1. The default telnet/

terminal password is ADTRAN.

Only one telnet/terminal session may be active at a time.

ADTRAN - TSU 600

Password: XXXXXXXX

Main Menu

1) Status

2) Config

3) Util

4) Test

5) Remote Menu Access

6) Management Config

7) Flash Download

8) Quit Session

Telnet/Terminal Main Menu

Figure 8-1.

61202076L1-1

TSU 600 User Manual

8-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 8. Telnet/Terminal Menus

Status, Config, Util, and Test Menu Options

These menu items can access the same modified menus that you can ac-

cess through the front panel. For detailed information on the available

menu options, refer to the following sections:

• Status Menu in Chapter 4.

• Configuration Menu in Chapter 5.

• Utility Menu in Chapter 6.

• Test Menu in Chapter 7.

DS0 Maps Configuration Menu

The Telnet/Terminal version of the DS0 maps configuration menu takes

advantage of the 24-line VT 100 display. Upon entering this menu, the

current Temp Map displays followed by nine selections that you can use

for configuring and reviewing map information.

TEMP MAP

DS0 #

PORT

IDLE

DS0 #

PORT

IDLE

1) COPY MAP A TO TEMP MAP

2) COPY MAP B TO TEMP MAP

3) CREATE TEMP MAP

4) REVIEW MAP A

5) REVIEW MAP B

6) REVIEW TEMP MAP

7) EDIT TEMP MAP

8) APPLY TEMP MAP TO MAP A

9) APPLY TEMP MAP TO MAP B

DS0 Temp Map

Figure 8-2.

• Use the up and down arrows or number keys to move the cursor

from one selection to another.

• Use the Enter key to perform the action displayed in the LCD to the

right of the cursor.

8-2

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 8. Telnet/Terminal Menus

Normally, map configuration involves these steps.

Step

Action

Initializes the Temp Map to one of three config-

urations (current Map A, current Map B, or all

IDLEs). This step is optional.

Edits the Temp Map so that it reflects the

desired map configuration.

Replaces the current DS0 map A or B configura-

tion with the Temp Map configuration.

Initializing the Temp Map

Upon entering the DS0 maps configuration menu, the Temp Map re-

flects its last configured state. You can then use the following selections.

Use selections... To initialize...

1, 2, 3

the displayed Temp Map to one of three

configurations.

1, 2

the Temp Map from its current configura-

tion to one which reflects the currently

stored Map A or B configurations, respec-

tively.

the Temp Map to an all IDLE state.

61202076L1-1

TSU 600 User Manual

8-3

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 8. Telnet/Terminal Menus

Editing the Temp Map

If further changes to the Temp Map are needed, do the following:

Step

Action

Explanation

Use selection 7 to enter Upon entering this mode, the cursor

the Temp Map edit

mode.

location moves to DS0 number one in the

DS0 field of the Temp Map.

The cursor may be moved from one DS0

to another by using the up and down

arrows until the cursor is located at the

DS0 number whose assigned port needs

to be changed.

Press the Enter key to

cause the cursor to move to scroll through the possible port selec-

The up and down arrows are then used

tions.

into the Port field.

Press the ESC key

This restores the previous port assign-

ment and returns to the DS0 field.

Press the Enter key

This saves the current selected port and

returns to the DS0 field.

Once the cursor is again located in the

Temp Map DS0 field, press the ESC key

a second time to return to selection 1

below the Temp Map display.

Applying the Temp Map

Once the Temp Map reflects the desired configuration, use selections 8

or 9 to apply this configuration to Map A or B, respectively.

Reviewing Maps

Selections 4 through 6 give a summary of the number of ports assigned

to Map A, Map B, and the Temp Map, respectively.

8-4

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 8. Telnet/Terminal Menus

Remote Menu Access

Displays telnet menus for a remote device (may be another TSU/TDU

or any other ADTRAN product that supports telnet via its EIA-232 chain

port). After selecting this option, you may choose to connect to a device

entered in the Unit Access Table or enter a Unit ID for a unit not in the

Unit Access Table. CTRL + X terminates the session and returns to the

TSU 600 Main Menu.

Management Configuration

This menu sets management information, such as SNMP community

names and trap destination addresses.

Unit Access Table

This menu edits and creates the Unit Access Table. This table stores the

Unit ID, Passcode, and Unit Type for units connected via chain ports or

connected remotely to the TSU/TDU (see Figure 8-3 on page 8-6). An

entry in the table is only required to support proxy SNMP MIB access or

polling. For MIB access, an entry is required only if the unit's passcode

is not the same as the Default Unit Passcode, or the unit is a single port

TSU Stand-alone.

It is not necessary to have an entry in this table for a remote unit in order to

telnet to it or forward SNMP traps from it. In the telnet case, the Remote Menu

Access menu is selected from the Main menu and a Unit ID is entered which

may or may not be in the Unit Access Table.

Units accessed via T-Watch PRO over TCP/IP use the Unit ID and pass-

code set by T-Watch PRO running on the PC.

61202076L1-1

TSU 600 User Manual

8-5

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 8. Telnet/Terminal Menus

__________________Unit Access Table_________________

Unit ID

Passcode

DEFAULT

0033

Type

Polled

PollStatus

Standard

TSU Stand Alone

Standard

Yes

0095

0022

Yes

1) Add New Unit

2) Modify Unit

3) Delete Unit

4) Default Unit Passcode

5) OK

0022

Unit Access Table

Figure 8-3.

Add New Unit

This adds a new device to the table. You must enter a device Unit ID,

passcode, unit type, and polled flag. The unit type can be Standard

(which supports any TSU/TDU Multiplexer and the ISU 512) or TSU

Standalone (a single port TSU with no option card slot). You can select a

passcode of 0 to 9999 for each device or DEFAULT, in which the de-

fault passcode will be used. See Figure 8-3.

Traps are normally sent from the unit in alarm to the TSU 600. For units

in the Unit Access Table that are not chained directly to the TSU 600 but

are managed over Inband or the FDL, traps are not automatically for-

warded. Polling must be enabled on the TSU 600 for these units in order

to receive Traps on the NMS. The TSU 600 can be configured to poll se-

lected units for traps by enabling the polled option when adding or

modifying a unit entry.

Modify Unit

Allows Unit ID, passcode, device type, and polled flag to be changed for

an existing entry in the table.

Delete Unit

Deletes an entry in the table.

8-6

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 8. Telnet/Terminal Menus

Default Unit Passcode

Sets the default passcode for all devices in the table that have passcodes

set to DEFAULT, or for any unit not listed in the table.

Returns to the Configure Agent menu.

SNMP Read Community

SNMP Read Community Name defaults to public. NMSs using this

community name have Read access for all supported MIB objects but do

not have the ability to change MIB objects. This value must be set to the

same value on both the TSU 600 and the NMS (OpenView®, etc.) in or-

der for the NMS to have Read access to MIBs supported by the TSU 600.

This value must be a text string of 16 characters or less.

SNMP Read/Write Community

SNMP NMS using this community name have full read/write access to

all supported MIB objects (defaults to private). This setting must be the

same value on both the TSU 600 and the NMS in order for the NMS to

have read/write access to MIBS supported by the TSU 600. This value

must be a text string that is 16 characters or less.

To access other units external to the TSU 600 (proxied units) using an SNMP

MIB browser, append a period and the Unit ID of the external device to the Read

Only and Read/Write community name used in the MIB Browser, for example,

public.4. See Appendix A, Understanding SNMP on page A-1, for more

information.

61202076L1-1

TSU 600 User Manual

8-7

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 8. Telnet/Terminal Menus

SNMP Trap Community

This community name is used for all SNMP traps forwarded by the TSU

600. Traps received from daisy chained units have a period and the Unit

ID appended to the trap community name.

SNMP Trap Destination Address

Description

Host 1 Trap IP Address

This is the first of four entries for

SNMP trap destination addresses.

The TSU 600 forwards all SNMP traps

to the IP address specified in this

entry. If the address is set to the

default value of 0.0.0.0, no traps are

forwarded for this particular value.

Host 2 Trap IP Address

Host 3 Trap IP Address

Host 4 Trap IP Address

Defaults to 0.0.0.0. Second destination

address for SNMP traps.

Defaults to 0.0.0.0. Third destination

address for SNMP traps.

Defaults to 0.0.0.0. Fourth destination

address for SNMP traps.

System Name

A text string that can uniquely identify an SNMP-managed node.

System Contact

A text string containing the name, phone number, etc. of the individual

responsible for maintaining an SNMP-managed node.

System Location

A text string describing the physical location of an SNMP-managed

node (for example, SECOND FLOOR PBX ROOM).

8-8

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 8. Telnet/Terminal Menus

Auto. Fail Traps Sent

(DISABLED, ENABLED: defaults to DISABLED)

When enabled, the TSU 600 issues an SNMP trap when any SNMP re-

quest is received with an invalid community name. Can be used for se-

curity purposes.

Poll Link Status Traps Sent

(DISABLED, ENABLED, defaults to DISABLED)

When enabled, the TSU 600 sends an SNMP trap whenever a device con-

figured to be polled fails to respond. When the device begins respond-

ing to polls, a poll link-up trap is sent. The formats of the traps are

defined in the agent MIB.

Ping IP Host

Allows the user to Ping a specific IP address.

Telnet/Terminal Time-out

The TSU 600 terminates a telnet or terminal session if no activity is de-

tected for this length of time. Only one telnet or terminal session may be

active at one time. This time-out prevents an unattended session from

blocking interactive access to the agent. The default value is five min-

utes.

Telnet/Terminal Password

This option allows modification of the password required for entry into

a telnet or terminal session. The default value is ADTRAN.

Exit

Returns to the TSU 600 Main menu.

Flash Download

The TSU 600 uses flash memory that allows software updates via the

chain-in port. This menu selection allows you to perform a flash down-

load manually using XMODEM. T-Flash is also available to automate

this process.

Quit Session

Terminates the telnet/terminal session.

61202076L1-1

TSU 600 User Manual

8-9

Download from Www.Somanuals.com. All Manuals Search And Download.

Chapter 8. Telnet/Terminal Menus

8-10

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Understanding SNMP

Appendix A

As local area network (LAN) environments became standardized over

the past ten years, multi-vendor equipment grew with competition. It

became necessary to manage the various vendor equipment from a sin-

gle control console. Thus, the SNMP emerged as the standard for man-

aging commercial TCP/IP networks.

The term SNMP broadly refers to the message protocols used to ex-

change information between the network and the managed devices, as

well as to the structure of network management databases.

Basic Components

SNMP has three basic components: Network Manager, Agent, and

MIB.

Network Manager

This is a control program that collects, controls, and presents data perti-

nent to the operation of the network devices. It resides on a network

management station.

Agent

This is a control program that responds to queries and commands from

the network manager and returns requested information or invokes

configuration changes initiated by the manager. It resides in each net-

work device.

61202076L1-1

TSU 600 User Manual

A-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix A. Understanding SNMP

MIB

This is an index to the organized data within a network device. It defines

the operating parameters that can be controlled or monitored. When re-

questing the network manager to retrieve or modify a particular piece of

information about a network device, the network manager transmits the

request to that network device. The agent in that device interprets the in-

coming request, performs the requested task, and sends its response to

the network manager. The network manager collects all the data from

the various network devices and presents it in a consistent form.

Commands

Using SNMP Version 1, the network manager can issue three types of

commands: GetRequest, GetNextRequest, and SetRequest.

Command

GetRequest

Description

This command retrieves a single item or

the first in a series from a network device.

GetNextRequest

SetRequest

This command retrieves the next item in

a series from a network device.

This command writes information to a

network device.

Message

The network device issues two types of messages:

GetResponse and Trap.

Command

Description

GetResponse

This message is the response to a network man-

ager GetRequest or GetNextRequest command.

Trap

This is an unsolicited message issued by a net-

work device to report an operational anomaly or

an alarm condition to the network manager. These

messages are typically encased within informa-

tional packets and transported over the LAN or

WAN (wide area network).

A-2

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix A. Understanding SNMP

TSU 600 SNMP ACCESS

By default, SNMP MIB Browser access to the TSU 600 IP address with

the configured community names, accesses the host. The TSU 600 can

also act as an SNMP proxy agent for external units. To access MIB vari-

ables on externally chained devices, append a period and the Unit ID of

the device to the Read and Read/Write community names.

Example:

If the Read community name configured in the TSU 600 is public, spec-

ifying "public.3" as the community name in the SNMP MIB Browser al-

lows reading SNMP MIB variables from externally chained unit 3.

If the external unit's passcode is not the default, an entry must be added

to the Unit Access Table for SNMP MIB access. See Figure 8-3 on page 8-

6 for a description of this operation. However, SNMP traps for the unit

can be forwarded without the entry.

SNMP Trap Configuration

Traps received by the TSU 600 from external units and the host unit are

converted into SNMP traps and forwarded to the configured NMS. The

source of the trap is uniquely identified at the NMS by a combination of

the IP address of the TSU 600, and the Unit ID of the sending device. The

Unit ID is present in the trap packet appended to the end of the trap

community packet name, for example public.4. It is also included as an

Octet String variable (adProdPhysAddress) in the trap packet as defined

in the individual product MIBs. The latest versions of the product MIBs

by default display the appended trap community name in their descrip-

tions.

Typical steps required for Management Station trap configuration are

loading the device specific MIBs and loading or creating device specific

Trap Definition Files. The current product MIBs contain keywords em-

bedded in comments that can be used by some network management

platforms to automatically generate Trap Definitions. Otherwise, the de-

scriptions may be used as a template for Trap Definitions.

If individual option card port identification and slot identification are

required, they are present in the four byte adProdPhysAddress field of

the trap packet. The first two bytes are the Unit ID of the base controller

(least significant byte first). The next two bytes are port and slot number.

This field is the second object identifier in all traps sent from TSU/TDU

products.

61202076L1-1

TSU 600 User Manual

A-3

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix A. Understanding SNMP

For traps from the ISU 512, the Unit ID is the first object identifier. See

the product MIBs for more information.

Definitions for Poll Link Up/Down traps are included in the TSU 600

MIB file: 600e.MIB.

The TSU 600 and TSU 600e share the same MIB.

SNMP MIB Browser Configuration

The steps required to configure Network Manager MIB variable access

through the TSU 600 are as follows:

1. Load the desired product MIBs on the network management station.

If, for example, the administrator is managing TSU 600 and ISU 512

devices, load TSU 600e.MIB, ISU512.MIB, and RFC1406.MIB.

2. Create device entries in the NMS database for all units that are to be

managed through the TSU 600. The host unit should be configured as

the Proxy agent for the external units. The IP address or host name

used for the proxy designation is that of the TSU 600.

3. Set community names in the device’s entries for external units to the

TSU 600 community name with the device Unit ID appended as de-

fined in the previous section, TSU 600 SNMP ACCESS on page A-3.

4. Set the device timeout for all device entries in the NMS device data-

base to five seconds, including the host unit.

SNMP MIB Files

The TSU 600 supports several standard MIBs including MIB-II (RFC-

1213), the DS1 T1/E1 MIB (RFC-1406), and the Ethernet MIB (RFC-

1643; 600e only). It also supports several ADTRAN enterprise specific

MIBs including the ADTRAN Product MIB (ADTRAN.MIB), the ADT-

RAN DS1 extensions MIB (ADS1.MIB), and all TSU/TDU Enterprise

MIBs, such as 600e.MIB. The standard MIB files are usually included

with most SNMP network management software.

The latest versions of the ADTRAN enterprise-specific MIBs are avail-

able in the following locations:

•

ADTRAN anonymous ftp site (ftp.adtran.com),

By dial-up from the BBS (256-963-8169).

ADTRAN web site at http://www.adtran.com.

A-4

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Understanding TR-08

Appendix B

The TSU 600 chassis functions as a Remote Terminal in Digital Loop

Carrier and as Integrated Digital Loop Carrier Systems as described in

TR-TSY 000008. The TSU 600 supports SLC96 framing, Mode I opera-

tion, ORB-13 and ORB-16 alarm formats, alarm reporting, and user-de-

finable BPV threshold detection rate.

A basic familiarity with DLC systems, IDLC systems, and TR-TSY-

000008 is assumed, but the following information will be useful:

•

All received TR-TSY-000008 specific alarms are reported locally

within the history feature of the TSU 600.

•

When the DISABLE ALARMS option is selected, no alarms will be

sent on the DLF, but received alarms will be reported locally in the

history.

•

Other alarms normally reported by the TSU 600 will also be placed

in history.

Each TSU 600 needs to be configured as the A SHELF, as it is provi-

sioned as a separate entity.

All alarms will refer to A SHELF when received from TSU 600.

61202076L1-1

TSU 600 User Manual

B-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix B. Understanding TR-08

The following table explains what conditions trigger alarms and how

alarms are processed when received by the TSU 600.

Alarm Conditions

Table B-1.

Name

FELP

Explanation

When the TSU 600 receives a FELP alarm, it will loop

the incoming data directly to the outgoing data. LINE

ON is placed in history. The alarms and loopback are

cleared when FELP is no longer received.

Loss of Data

The TSU 600 will send MINOR ALARM and the A

SHELF ALARM for 2.5s when it quits receiving the

data link on the T-Span. It will also report TR-08 DL

Down in the history. After 2.5s, MAJOR ALARM, A

SHELF ALARM are sent across the Data Link.

OOF

The TSU will send MINOR ALARM and A SHELF

ALARM upon receiving an out-of-frame condition.

TR-08 DL Down and RED ALARM are declared in

history for severe framing errors. After 2.5s, MAJOR

ALARM, A SHELF ALARM are sent across the Data

Link.

Loss of Signal The TSU 600 will send MINOR ALARM and the A

SHELF ALARM for 2.5s when it quits receiving a

signal from the far end. It will also report TR-08 DL

Down and LOS in the history. After 2.5s, MAJOR

ALARM, A SHELF ALARM are sent across the Data

Link, and RED ALARM is declared in history.

BPVs

BPVs that are received at a rate greater than the

threshold set under TR-08 options, will cause

MINOR ALARM and A SHELF ALARM to be sent

on the DL. If the BPVs remain above the threshold for

2.5s, the TSU 600 will send MAJOR ALARM and on

the DL. No events are placed in history.

Protection

Line Switch

The TSU will not respond to this alarm.

B-2

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix B. Understanding TR-08

TR-08 DS0 Conversion Table

The following table contains the mapping conversions needed to map

voice ports to the TR-08 network.

TR-08 DS0 Conversion Table

Table B-2.

DS0

TR-08 Channel Number

Port

1.1

1.2

1.3

1.4

2.1

2.2

2.3

2.4

3.1

3.2

3.3

3.4

4.1

4.2

4.3

4.4

5.1

5.2

5.3

5.4

6.1

6.2

6.3

6.4

61202076L1-1

TSU 600 User Manual

B-3

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix B. Understanding TR-08

B-4

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Network Pinouts

Appendix C

WIRING

Network

On the rear panel of the TSU 600 is an 8-position modular jack labeled

NETWORK. This connector is used for connecting to the network. See

Table C-1, Network Pinouts for the pinout for the network connector.

Network Connections

The network connections are as follows:

Connector Type

Part Number

(USOC) RJ-48C

AMP# 555164-2

Network Pinouts

Table C-1.

Name

Description

R1 RXDATA-RING

T1 RXDATA-TIP

UNUSED

Receive data from the network

R1 TXDATA-RING

T TXDATA-TIP

UNUSED

Send data toward the network

6,7,8

61202076L1-1

TSU 600 User Manual

C-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix C. Network Pinouts

Control In/Chain In

This is used as an EIA-232 port for connection to a computer or modem

(Control-in) or to another TSU 600 or TSU 100 (chain-in). See Table C-2,

Control In/Chain In Pinout for the pinout for the control-in/chain-in con-

nector.

Chain-in Connections

The chain-in connections are as follows:

Connector Type

Part Number

RJ-48

AMP# 555164-2

Control In/Chain In Pinout

Table C-2.

Name

GND

Description

Ground-connected to unit chassis

Request to send-flow control

Data received by the TSU 600

RTS

RXDATA

UNUSED

TXDATA

UNUSED

CTS

Data transmitted by the TSU 600

Clear to send -- flow control

6,7

C-2

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix C. Network Pinouts

Chain-Out

This is used to connect to another TSU 600 chain-in connector. See Table

C-3, Chain-Out Pinout for the pinout for the chain-out connector.

Chain-out Connections

The chain-out connections are:

Connector Type

Part Number

RJ-48

AMP# 555164-2

Chain-Out Pinout

Table C-3.

Name

GND

Description

Ground-connected to unit chassis. Connected to

GND of next unit (pin 10).

UNUSED

TX DATA Data transmitted to chained units by the TSU

600. Connect to RX DATA of the next unit (chain-

in pin 3).

UNUSED

RX DATA Data received from chained units by the TSU

600. Connect to TX DATA of the next unit (chain-

in pin 5).

6,7,8 UNUSED

61202076L1-1

TSU 600 User Manual

C-3

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix C. Network Pinouts

10BaseT (600e only)

10BaseT is used to connect the TSU 600e to the Local Area Network. See

Table C-4.

10BaseT Connections

The required wiring connections are:

Connector Type

Part Number

(USOC) RJ-45

AMP# 555164-1

10BaseT Ethernet

Table C-4.

To NIC

TX1

TX2

RX1

RX2

C-4

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

System Messages

Appendix D

This appendix lists and defines the alarm and status messages that ap-

pear on the TSU 600 screen.

Alarm Messages: Network Interface (NI)

Message

Description

Red Alarm

NI unable to frame align with incoming signal

Yellow Alarm Remote alarm indication (RAI) being received from

far end

Blue Alarm

Unframed all ones (1s) (AIS) being received at NI

Loss of Signal No signal detected at NI

61202076L1-1

TSU 600 User Manual

D-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix D. System Messages

Status Messages: Network Interface (NI)

Message

Description

Payload On

Line On

Payload loopback activated

Loopback off

Loopback Off

All loopbacks deactivated

Factory Restore Factory setting restored

Power On

Self-Test

Unit powered on

Internal self-test performed

TR-08 DL Down* TR-08 data link is down

TR-08 DL Up*

Minor Alarm*

TR-08 data link is up

Loss of sync, carrier loss, BPV threshold

exceeded, or data link failure.

Major Alarm*

Conditions for a minor alarm have contin-

ued for greater than 2.5 seconds.

*TR-08 alarm messages appearing in the alarm or history log have

been received from the far end. If the NI detects one of the above

conditions, it will send the appropriate alarm (if enabled) to the far end

but no message will appear in the alarm or history log.

D-2

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

Appendix E

ELECTRICAL SPECIFICATIONS

T1/FT1 Interface

T1 Line Rate

Line Code

Framing

1.544 Mbits/s ± 75bps

Bipolar, RZ; AMI or B8ZS

D4(SF), ESF, or SLC96

FT1 Line Rate

DS0 Channelized (multiple of 64 kbps)

Transmit Timing Network, DTE, U-BR1TE Secondary NI, Nor-

mal (CSU) or Internal

Input Signal

Line Build-out

Connector

0 to -36 dB (DS-1)

0, 7.5, 15, 22.5 dB, AUTO

RJ-45

Test Jacks

Bantam jacks: TX and RX (to Network) and

MON

61202076L1-1

TSU 600 User Manual

E-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix E. Specifications

Compatibility

T1 Interface

Pub 62411

TR. 194

ESF Format Interface

ESF Performance Monitoring TR. 54016 and T1.403

Approvals:

FCC Part 15

FCC Part 68

UL 1950

Management Interfaces

Chain-In/Chain-Out Ports

Interface Devices PC Serial Port, Modem or SLIP

connection to router

Interface Type

Data Rates

EIA-232

1200, 2400, 4800, 9600, 19200,

38400

Data Format

Protocols

EIA-232 N81

TWATCH/ADLP, ATEL/ADLP,

SLIP, TCP/IP

Connector

RJ-45

Option Slot Interface

Slots 1-6

Interface

ADTRAN proprietary, accepts standard TSU

Option Modules.

Chassis Specification

Height Less than 5.25-inch (will fit in a 3U rack mount opening)

Width Will fit within a 19-inch rack

E-2

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix E. Specifications

Environmental Specifications

Input Power TSU 600:

90 - 130 VAC 60 HZ

TSU 600e:

90 - 120 VAC 50/60 HZ

DC powered units:

21 - 26 VDC or 40 - 56 VDC

Fuse

AC powered units:

1A, 250V

DC powered units:

5A, 250V

Operating

Temperature

0 to 45 degrees C

40 W

Max Power

Consumption

Max Current AC powered units: 0.7A

DC powered units: 3A

61202076L1-1

TSU 600 User Manual

E-3

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix E. Specifications

E-4

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

ANSI FDL PLB, remote loopback 7-

Numerics

10BaseT Connections C-4

10BaseT Interface 2-10

10BaseT, interface with SNMP 3-12

ANSI FT1 LLB, remote loopback 7-

APPLY TEMP > A, DS0 map menu

item 5-13

Applying the Temp Map, how to 8-

Access, unit menu 5-9

Active Alarms 4-4

AS, available sec., NI errors 4-2

ATT In-Band LLB, remote loopback

7-4

Add New Unit to unit access table,

how to 8-6

Auto. Fail Traps Sent, SNMP 8-9

ADTRAN

Management

Program, T-Watch PRO 3-11

ADTRAN PC Program, T-Watch

PRO 3-11

ADTRAN Web page 3-12

Agent, SNMP component A-1

AIS Alarm, (Blue Alarm) network

interface alarm message D-1

Alarm (red), LED description 3-2

Alarm (red), module status LED 3-

Backup Power Supply for TSU 600e

2-2

BES, pattern result, test menu 7-6

BIT STUFFING, network menu

item 5-3

Blue Alarm, (AIS alarm), network

interface alarm message D-1

Board level tests 2-12

Alarm Conditions, TR-08 B-2

Alarm Format, TR-08 5-3

Alarm Messages

Board level tests, run self-test 7-7

BPV Threshold, TR-08 5-3

BPV, TSU 600 T1 error 4-3, 5-3

BPVs, alarm condition TR-08 B-2

Network Interface (NI) D-1

Alarm

Messages,

Network

Interface D-1

Alarm Report, TR-08 5-3

Alarm, operation key 3-5

Cancel Tests, test menu 7-8

Cancel, front panel 3-1

Chain In/Chain Out 2-13

ANSI FDL LLB, remote loopback 7-

61202076L1-1

TSU 600 User Manual

Index-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

Chain Port Output 2-9

Chain-In (PC) 2-13

Chain-in Connections C-2

Chain-out Connections C-3

Chain-Out Pinout C-3

Chassis Specification E-2

Clear alarm history 4-4

Clear Port Alarm 4-5

Clear,operation key 3-5

CMD Mode, utility menu 6-4

Config, front panel menu 3-10

configuration applications, TSU 600

1-5

Configuration Menu Tree 5-1

Control Port Input 2-9

Control Port, unit menu 5-9

COPY A >TEMP, DS0 map menu item

5-12

Copy, operation key 3-5

CRC, TSU 600 T1 error 4-3

CREATE TEMP, DS0 map menu item

5-12

Create Temp, example, how to 5-13

Ctl Port Rate, unit menu 5-9

1-3

DSX1 , option module for TSU 600 1-

DTE Timing 5-5

EDIT TEMP, DS0 map menu item 5-

Editing the Data Field, how to 3-7

Editing the Temp Map, how to 8-4

EF, error free sec., NI errors 4-2

Electrical specifications, TSU 600 E-1

ENET Address, utility menu 6-4

ENET Status 4-6

Enter, front panel 3-1

Environmental Specifications E-3

Error (red), LED description 3-2

ES, Errored Sec., NI Errors 7-6

ES, errored sec., NI errors 4-2

Exit Any Menu Field Operation Or

Display, how to 3-8

Factory Restore, network interface

status message D-2

features, TSU 600 1-2

Data Port Identification 3-9

data port identification 3-9

DC Powered TSU 600, about 2-2

Default Router,unit menu 5-10

Delete Unit in unit access table, how

to 8-6

FELP, alarm condition TR-08 B-2

FER, TSU 600 T1 error 4-3

Flash Download 8-9

Flash Download, telnet/terminal

menu 8-9

Front Panel Menu Structure 3-10

front panel menu tree 3-6

Front Panel, description 3-1

Full Drop and Insert, option module

for TSU 600 1-3

Dial Backup, option module for TSU

600 1-3

Display Only Data Fields 3-8

Drop and Insert, Voice and Router

Application 1-6

DS0 Map A and DS0 Map B Menu 5-

DS0 Maps Configuration Menu 8-2

DSO Map A and DSO Map B 5-12

DSU DP, option module for TSU 600

GetNextRequest, SNMP command

A-2

GetRequest, SNMP command A-2

Index-2

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

GetResponse, SNMP message A-2

Grounding Instructions 2-4

message D-2

Management Configuration 8-5

Management software - T-Watch PRO

3-11

Map Exchange Menu 5-11

MAP In Use

Home, operation key 3-5

http

A(B) Menu 5-11

//www.adtran.com, ADTRAN

Web page 3-12

MIB, SNMP component A-2

Minor Alarm, network interface

status message D-2

Modify Unit to unit access table, how

to 8-6

Module Status LEDs 3-5

INBAND LPBCK, network menu

item 5-3

Init Modem, unit menu 5-9

Initialization 2-12

Initializing the Temp Map, how to 8-

Network 7-2

Network

configuration menu 5-2

Network (NI), configuration menu 5-

network connections, pinouts C-1

Network Interface Errors 4-3

Network Interface Loopbacks, test

menu 7-3

network interface, (NI) port 2-9

Network Manager, SNMP component

A-1

Network Performance Reports 4-2

Network Test Interface 2-9

Network Tests, test menu 7-2

Network, pinouts C-1

(NI)

Item,

Installing and Replacing the Power

Supply, how to 2-3

Internal Timing 5-6

IP Address, unit menu 5-9

LCD Menu Options 3-10

LCD Window, front panel 3-1

Line On, network interface status

message D-2

Line On, setting local loopback 7-3

Local Loopbck, test menu 7-3

Loopback Off, network interface

status message D-2

Loopback Tests, test menu 7-2

Loss of Data, alarm condition TR-08

B-2

Loss of Signal, alarm condition TR-08

B-2

Loss of Signal, network interface

alarm message D-1

NI errors, AS (available sec.) 4-2

NI errors, EF (error free sec.) 4-2

NI errors, ES (errored sec.) 4-2

NI Errors, ES, Errored Sec 7-6

NI errors, SES, Severly Errored

Seconds 7-6

NI errors, SES, severly errored

seconds 4-2

NI errors, UAS (unavailable errored

sec.) 4-2

No Loopback, remote loopback 7-4

Major Alarm, network interface status

61202076L1-1

TSU 600 User Manual

Index-3

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

No Loopback, setting local loopback

7-3

message D-2

power-up procedure 2-14

Power-up Testing 2-11

No Unit ID Desired, utility menu,

what to do 6-4

Product Description, TSU 600 1-1

Product Overview, TSU 600 1-1

Protection Line Switch, alarm

condition TR-08 B-2

Proxy Traps, unit menu 5-10

PS Status, power supply 4-6

Normal (CSU) Timing 5-8

Normal Power-Up Procedure 2-14

Numeric Keypad, front panel 3-1

Nx56 1-3

Nx56/64 module, router interface 1-6

Nx56/64 Serial Interface, option

module for TSU 600 1-3

NxIQ, option module for TSU 600 1-3

QRSS Pattern, test menu 7-5

Quit Session, telnet/terminal session

8-9

OCU DP, option module for TSU 600

1-3

OFF, map exchange menu 5-11

OK (green), LED description 3-2

OK (green), module status LED 3-3

OOF, alarm condition TR-08 B-2

operation keys 3-5

Option Module Architecture 1-4

Option Module Architecture, for TSU

600 1-4

Option Slot Arrangement, for TSU 600

2-10

Rear Panel Layout, of TSU 600 2-5

Receipt Inspection, for TSU unit 2-1

Red Alarm, network interface alarm

message D-1

Remote Loopbk 7-4

Remote Menu Access 8-5

Remote Port 4-5

REVIEW MAP A(B), DS0 map menu

item 5-13

REVIEW TEMP, DS0 map menu item

5-13

Reviewing Maps, how to 8-4

router interface with Nx56/64

module 1-6

Pattern Result, test menu 7-6

Payload On, network interface status

message D-2

Payload On, setting local loopback 7-

Router, PBX, Video Conferencing

Application 1-5

Run Self-Test, test menu 7-7

Ping IP Host, SNMP 8-9

Poll Link Status Traps Sent, SNMP 8-

Secondary Timing 5-7

port configuration 5-15

Port Status 4-5

Selecting and Activating a Menu Item,

how to 3-6

Port Tests, test menu 7-8

Port Utility, utility menu 6-4

Power Connection for TSU 600 2-2

Power On, network interface status

Self-Test, network interface status

message D-2

SES, Severly Errored Seconds, NI

Index-4

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

errors 7-6

SES, severly errored seconds, NI

errors 4-2

Telnet Connection 3-13

Set Control Port 2-13

Telnet/Terminal Main Menu 8-1

Telnet/Terminal Password, SNMP 8-

SET LBO, network menu itme 5-3

Set Passcode, how to 6-2

Set Unit Identification 2-12

Set User Passcode 2-12

Telnet/Terminal Time-out, SNMP 8-

SetRequest, SNMP command A-2

Setting the Unit Identification for

utility menu, how to 6-4

Shift, front panel 3-2

Terminal Mode Connection 3-13

Test (yellow), LED description 3-2

Test (yellow), module status LED 3-3

Test menu 7-1

Test Pattern, test menu 7-5

Test, front panel menu 3-10

TR-08 alarm conditions B-2

TR-08 DL Down, network interface

status message D-2

TR-08 DL Up, network interface

status message D-2

TR-08 DS0 Conversion Table B-3

TR-08,network menu item 5-3

Trap, SNMP message A-2

Traps, unit menu 5-9

TSU 600 Clock Sources 5-4

TSU 600 Configuration Applications

1-5

TSU 600 Electrical specifications E-1

TSU 600 Front Panel Layout, with

descriptions 3-4

TSU 600 General Menu Operation 3-5

TSU 600 Interfaces 2-6, 2-9

TSU 600 interfaces 2-6

shipping damages, what to do 2-1

Simple

Network

Management

Protocol (SNMP) 3-12

SLIP Flow CTL, unit menu 5-10

SLIP Rate, unit menu 5-10

SNMP Commands A-2

SNMP Messages A-2

SNMP MIB Browser Configuration

A-4

SNMP MIB Files A-4

SNMP Trap Community 8-8

SNMP Trap Configuration A-3

SNMP, Basic Components A-1

SNMP, how to use with TSU 600 3-12

Software Revision (Software Rev),

utility menu 6-4

Status menu, description 4-1

Status Messages, Network Interface

D-2

Status, Config, Util, and Test Menu

Options 8-2

Status, front panel menu 3-10

Subnet Mask, unit menu 5-10

SYNC, pattern result, test menu 7-6

System (green), module status LED 3-

system contact, SNMP text string 8-8

system location, SNMP text string 8-8

system name, SNMP text string 8-8

TSU 600 Option Modules, option

modules, for TSU 600 1-3

TSU 600 SNMP access A-3

TSU 600, Overview 1-1

TSU 600, power connection 2-2

TSU 600, Standard Features 1-2

TSU Product Description 1-1

T-Watch PRO 3-11

T-Watch PRO, modem connection 3-

T-Watch PRO/EIA-232 Connection

61202076L1-1

TSU 600 User Manual

Index-5

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

3-12

T-Watch PRO/LAN Connection 3-11

Voice Interface, option module for

TSU 600 1-3

UAS, unavailable errored sec., NI

errors 4-2

U-BR1TE (Slot 1) 5-5

Wiring, network pinouts C-1

U-BR1TE , option module for TSU 600

1-3

Unit Access Table 8-5

unit level tests 2-12

Unit level tests, run self-test 7-7

Unit Menu 5-9

XS0, TSU 600, T1 alarm 4-3

Up and down arrows, front panel 3-1

Util, front panel menu 3-10

utility menu tree 6-1

Yellow Alarm, network interface

alarm message D-1

Index-6

TSU 600 User Manual

61202076L1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

Product Support Information

Presales Inquiries and Applications Support

Please contact your local distributor, ADTRAN Applications Engineering,

or ADTRAN Sales:

Applications Engineering (800) 615-1176

Sales

(800) 827-0807

Post-Sale Support

Please contact your local distributor first. If your local distributor cannot

help, please contact ADTRAN Technical Support and have the unit serial

number available.

Technical Support

(888) 4ADTRAN

Repair and Return

If ADTRAN Technical Support determines that a repair is needed, Technical

Support will coordinate with theCustomer and Product Service (CaPS) de-

partment to issue an RMA number. For information regarding equipment

currently in house or possible fees associated with repair, contact CaPS di-

rectly at the following number:

CaPS Department (256) 963-8722

Identify the RMA number clearly on the package (below address), and re-

turn to the following address:

ADTRAN, Inc.

CaPS Department

6767 Old Madison Pike

Progress Center

Building #6, Suite 690

Huntsville, AL 35807

RMA # _____________

Download from Www.Somanuals.com. All Manuals Search And Download.

2Wire Network Router 1000S User Manual
3Com Network Card V7350 User Manual
3M Projector S15i User Manual
Adaptec Network Card USB2connect Host Bus Adapter User Manual
Addonics Technologies Network Card WDAUSM User Manual
Aiphone Home Security System MY 1HD User Manual
Airlink101 Network Router APO1000 User Manual
Altinex Network Card DA1926AV User Manual
Axis Communications Security Camera AXIS P3214 V User Manual
Axis Communications Security Camera P1427 LE User Manual