MP8630 Multimedia Projector
Operator's Guide
MP8630 Projecteur multimédia Guide de l'opérateur
MP8630 Multimedia-Projektor Benutzerhandbuch
Proyector de Multimedia MP8630 Manual del Usuario
MP8630 Proiettore Multimediale Manuale dell'operatore
MP8630 Bruksanvisning for multimediaprojektor
MP8630 Multimedia Projector Gebruiksaanwijzing
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
THANK YOU FOR CHOOSING 3M
Thank you for choosing 3M Multimedia Projector equipment. This product has been produced in accordance
with 3M's highest quality and safety standards to ensure smooth and trouble free use in the years to come.
For optimum performance, please follow the operating instructions carefully. We hope you will enjoy using this
high performance product in your meetings, presentations and training sessions.
LIMITED WARRANTY
3M warrants this product against any defects in material and workmanship, under normal usage and storage, for a
period of one year from date of purchase. Proof of purchase date will be required with any warranty claim. In
the event this product is found to be defective within the warranty period, 3M's only obligation and your
exclusive remedy shall be replacement of any defective parts (labor included).
To obtain warranty service, immediately notify the dealer from which you purchased the product of any defects.
The dealer has the option of repairing the product or returning it to 3M for repair or replacement. In the USA
call 1-800-328-1371 for warranty or repair service.
LIMITATION OF LIABILITY
THE FOREGOING WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, AND 3M
SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTIBILITYAND FITNESS. 3M SHALL NOT BE
LIABLE FOR ANY DAMAGES, DIRECT, CONSEQUENTIAL, OR INCIDENTAL, ARISING OUT OF THE USE OR INABILITY
TO USE THIS PRODUCT.
Important: The above warranty shall be void if the customer fails to operate product in accordance with 3M's
written instructions. This warranty gives you specific legal rights and you may have other rights which vary from
state to state.
FCC STATEMENT - CLASS A: This equipment generates, uses and can radiate radio frequency energy, and if
not installed and used in accordance with the instruction manual may cause interference to radio communications.
It has been tested and found to comply with the limits for a Class "A" computing device pursuant to Subpart B of
Part 15 of the FCC Rules, which are designed to provide reasonable protection against such interference when
operated in a commercial environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his/her own expense will be required to take whatever measures may be
required to correct the interference.
EEC STATEMENT: This machine was tested against the 89/336/EEC (European Economic Community) for
EMC (Electro Magnetic Compatibility) and fulfills these requirements.
Video signal cables: Double shielded coaxial cables (FCC shield cable) must be used and the outer shield must
be connected to the ground. If normal coaxial cables are used, the cable must be enclosed in metal pipes or in a
similar way to reduce the interference noise radiation.
Video inputs: The input signal amplitude must not exceed the specified level.
IBM is a registered trademark of International Business Machines Corporation. Apple Macintosh and Apple
©
Powerbook are registered trademarks of Apple Computer, Inc. Microsoft and Windows 95 are registered
trademarks, and Windows and Windows for Work Groups are trademarks of the Microsoft Corporation. All
other products are trademarks or registered trademarks of their respective companies. Toshiba is a registered
trademark of Toshiba Corporation.
© 3M 1997
3M™ Multimedia Projector MP8630
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Safeguards
IMPORTANT SAFEGUARDS
1.
Read and understand all instructions before using.
Pay particular attention to areas where this
symbol is shown.
WARNING - Indicates a potentially hazardous situation which, if not avoided, could result
in death or serious injury.
Caution - Indicates a potentially hazardous situation which, if not avoided, could result
in minor or moderate injury. It may also be used to alert against unsafe practices.
2.
3.
Close supervision is necessary when any appliance is used by or near children. Do not leave
appliance unattended while in use.
Never look directly into the projector lens when the lamp is on. The metal halide lamp produces
a strong light which could damage your eyesight.
4.
5.
Care must be taken as burns can occur from touching hot parts.
Do not operate appliance with a damaged cord or if the appliance has been dropped or
damaged – until it has been examined by a qualified service technician.
6.
7.
Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
If any extension cord is necessary, a cord with a current rating at least equal to that of the
appliance should be used. Cords rated for less amperage than the appliance may overheat.
8.
Always unplug appliance from electrical outlet before cleaning and servicing and when not in
use. Grasp plug and pull to disconnect.
9.
To reduce the risk of electric shock, do not immerse this appliance in water or other liquids.
10. To reduce the risk of electric shock, do not disassemble this appliance, but take it to a qualified
technician when service or repair work is required. Incorrect assembly can cause electric shock
when the appliance is subsequently used.
11. Connect this appliance to a grounded outlet.
12. This unit is equipped with optical lenses and should not be exposed to direct sunlight.
13. Keep ventilation opening free of any obstructions.
14. Always open the lens shutter when the projection lamp is on.
SAVE THESE INSTRUCTIONS
The information contained in this manual will help you operate and maintain your 3M MP8630
Multimedia Projector.
3M™ Multimedia Projector MP8630
© 3M 1997
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Unpack
1.1 Contents of Shipping Box
The 3M™ MP8630 Multimedia Projector is shipped with the necessary cables required for standard VCR, PC,
MAC™ II or laptop computer connections. Carefully unpack and verify that you have all of the items shown
below in Figure 1.1.
Remote Control Transmitter
MP8630 Multimedia Projector
(batteries included)
Power Cord
110V – US
220V – UK, Europe
3-Conductor
Video/Audio Cable
VGA Cable
(15-15 pin M/M)
Adapter
with dip switch
Video Cable
(S-Video mini DIN4-pin)
Figure 1.1 Inventory of Shipping Box
The shipping carton contains the items illustrated in Figure 1.1. In addition, the following items are also
included, but not shown here. If any of these items are missing, please contact your place of purchase.
•
•
•
•
PS/2 mouse cable .............. (1)
ADB mouse cable ............. (1)
Serial mouse cable ............ (1)
Stereo mini-jack ................ (1)
1.2 Optional Accessories
•
RS232 control cable .......... (1)
1.3 Keep Your Packaging Materials
Important:
Save the shipping box and packing materials in the event the MP8630 should require shipping
to a 3M Service Center for repair.
1.4 What Next?
After you have unpacked the MP8630 system and identified all the parts, you are ready to set up the projector.
© 3M 1997
3M™ Multimedia Projector MP8630
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Product Description
2.1 Machine Characteristics
The MP8630 Multimedia Projector integrates metal halide lamp and polysilicon LCD display technology into a
single unit. It accepts input from two different computer sources and two video/audio sources and projects a bright,
super crisp image. Switching your presentation from a computer to a video image, and then back to a computer
simply requires the push of a button on the remote control keypad or control panel keypad.
The MP8630 Multimedia Projector offers the following features:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
500 lumens (A highly efficient optical system with a metal halide lamp ensures high brightness)
SVGA resolution (3 separate 800 x 600 LCD panels are used for the R, G and B signals)
XGA compression
Compact size, light weight for portability
RGB (computer video) output terminal
Serial, PS/2 and Apple© Desktop Bus (ADB) mouse emulation
Power zoom and power focus functions
Easy to set up and use
Ability to display 16.7 million colors
Two computer input connections
Two video input connections (composite and S-video compatible)
Full function remote control
Two built-in stereo speakers (2 watt)
Horizontal and vertical image inverting function
Horizontal and vertical image position control
Fixed keystone correction
On screen menu with seven languages
Universal power supply
IR sensor in front and rear for maximum remote control range
RS232 control capability
Optional ceiling mount kit
3M™ Multimedia Projector MP8630
© 3M 1997
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2 Main Unit Identification
LAMP indicator
ON indicator
STANDBY / ON
button
Speakers
Power ON/OFF button.
OFF sets the unit in
standby mode.
Remote control
sensor
Handle
TEMP Indicator
MUTE button.
ZOOM button
Adjusts picture size.
Lens
Cooling fan
(inside)
Cooling fan
(exhaust)
Remote
control sensor
FOCUS button
Adjusts focus.
Lens shutter
MENU button
RESET button
Resets unit to factory
settings.
INPUT button
To select the input source.
Each time this button is pressed, the input source
is changed in sequence as shown below.
RGB1
RGB2
VIDEO1
VIDEO2
VIDEO input terminal
S-VIDEO input terminal
VIDEO input terminal
RGB input terminal
RGB input terminal
AUDIO input terminal
Stereo mini jack
AUDIO L/R input terminal
RGB output terminal
RGB output terminal
AUDIO output terminal
(RGB/VIDEO)
MAIN POWER switch
Main power ON/OFF switch.
Stereo mini jack
: OFF
: ON
AC IN socket
Connect the provided power cord.
CONTROL terminal
D-sub 15pin terminal
© 3M 1997
3M™ Multimedia Projector MP8630
7
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 System Set Up - connecting various equipment
AC In Socket
VCR with S-VHS out
Laptop Computer
Desktop Computer
VCR or Laser Disc
Caution: Turn power off to all devices before making connections. Never plug anything into the
projector or computer while the units are in operation.
The MP8630 must be powered down when making connections. The mouse emulation may
not work if the unit is not powered down after the mouse cable connections are made.
2.3.1 Apple™ Desktop Mouse - The ADB operating system should recognize the MP8630 as a mouse
without any drivers being loaded.
Virtual Mouse for PCs - Setting up for most personal computers (IBM™ compatible). When setting up
the virtual mouse function on the projector, the following must be done, if the operating system fails to
recognize the projector as a mouse:
•
Change mouse driver information to "Serial Mouse" or "PS/2 Mouse."
Windows™ 95 - Click "Start"; select "Settings"; select "Control Panel". Click on "Mouse"; select the
"General" tab; (see what driver is currently loaded and make note of it); select "Change"; select "Show all
compatible devices"; (make note of the current Manufacturer and Model); select "Standard Mouse Type"
for Manufacturer; then select "Standard Serial Mouse" or "Microsoft™ PS/2 Port Mouse." Click OK to
change and apply the new driver. Restart Windows when prompted.
Windows™ 3.1 - From "Program Manager" click "Main"; then click "Windows Setup", (make note of what
the current mouse driver is); Click "Options"; then "Change Systems Settings". Choose "Mouse". It
should be listed as "Microsoft or IBM PS/2".
Note: Always remember, once all PC settings have been made, turn the projector on FIRST, then turn on
and boot the PC/laptop.
For some laptop computers you may need to disable the internal pointing device (IPD). This is done through
the BIOS level set up of the particular machine, or it could be listed in a "Utilities" program group, i.e.,
"Toshiba Utilities™," or "Thinkpad Utilities™."
3M™ Multimedia Projector MP8630
© 3M 1997
8
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4 Remote Control Transmitter Identification
STICK SWITCH
If Menu is on screen, stick switch
controls movement within menu.
If Menu is not displayed, stick switch
is used for mouse emulation, i.e. left
mouse button and cursor movement.
STANDBY / ON button
Power ON/OFF button.
OFF sets the unit in standby mode.
RESET / RIGHT button
If Menu is on screen, button resets
menu to factory default settings.
If Menu is not displayed, button is used
for mouse emulation, i.e. right mouse
button.
ZOOM button
Adjusts picture size.
TIMER ON / OFF button
Displays or removes TIMER.
When the blank screen is displayed,
TIMER can not be displayed.
MENU ON / OFF button
Displays or removes the on-screen
menus.
FOCUS button
Adjusts focus.
VOLUME button
Adjusts volume.
BLANK ON / OFF button
Blanks the screen. Pull down or left on
stick switch to reveal screen.
MUTE button
Disables sound.
POSITION button
Hold this button and move stick switch
to adjust vertical and horizontal image
position.
INPUT SELECT buttons
Selects the input source.
How to insert batteries: Insert the provided batteries (AA or R6P) into the remote control transmitter.
1. Remove the battery
compartment cover.
Slide the battery compartment
cover in the direction of the
arrow while pressing slightly
down on it.
2. Insert the batteries as
illustrated inside the
battery compartment.
3. Replace the cover.
© 3M 1997
3M™ Multimedia Projector MP8630
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Basic Operations
3.1 Installation
Example of the Multimedia projector and screen installation. Determine picture size and projection distance as
illustrated below.
Maximum
Zoom
Minimum
Zoom
178"
107"
72"
36"
24"
48"
71"
119"
DISTANCE
Minimum Image
Maximum Image
Distance
To Screen
Diagonal
Width
Height
Diagonal
Width
Height
227 cm
(7.4 ft)
102 cm
(40 in.)
81 cm
(32 in.)
61 cm
(24 in.)
153 cm
(60 in.)
122 cm
(48 in.)
92 cm
(36 in.)
341 cm
(11.2 ft)
152 cm
(60 in.)
121 cm
(48 in.)
91 cm
(36 in.)
228 cm
(90 in.)
183 cm
(72 in.)
137 cm
(54 in.)
455 cm
(15 ft)
202 cm
(80 in.)
162 cm
(64 in.)
121 cm
(48 in.)
304 cm
(120 in.)
243 cm
(96 in.)
182 cm
(72 in.)
569 cm
(18.7 ft)
252 cm
(99 in.)
202 cm
(79 in.)
151 cm
(60 in.)
379 cm
(149 in.)
303 cm
(119 in.)
227 cm
(90 in.)
682 cm
(22.4 ft)
302 cm
(119 in.)
241 cm
(95 in.)
181 cm
(71 in.)
454 cm
(179 in.)
363 cm
(143 in.)
272 cm
(107 in.)
853 cm
(28.0 ft)
377 cm
(148 in.)
302 cm
(119 in.)
226 cm
(89 in.)
556 cm
(223 in.)
453 cm
(178 in.)
340 cm
(134 in.)
1137 cm
(37.3 ft)
502 cm
(198 in.)
402 cm
(158 in.)
301 cm
(119 in.)
755 cm
(297 in.)
604 cm
(238 in.)
453 cm
(178 in.)
Note: These sizes are ± 1 inch. This is due to variations in the manufacture of the lens. If you are close to one of the
endpoints you should verify with your unit that the image is the proper size at the proper distance.
3M™ Multimedia Projector MP8630
© 3M 1997
10
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 Using the Projector
4 5
7
3
2
4
5
7
1
2
Note: Make all cable connections and line hookups FIRST.
1
2
3
Turn the MAIN POWER switch of the projector on.
• The ON indicator will light up orange.
Open the lens shutter.
• Push down lens shutter switch to open.
Press the STANDBY/ON button.
• The ON indicator blinks (green) and then lights (green).
• The ON indicator will blink green during warm-up and lamp ignition.
4
5
Adjust the screen size using the ZOOM button.
Adjust the focus using the FOCUS button.
(1) Press the FOCUS button. The on-screen display shown on the right appears.
(2) Adjust the focus so that the picture is sharp using the FOCUS button.
6
7
Turn on all connected equipment.
The method of connecting various equipment, see section 2.3.
Press the INPUT button on the projector or the INPUT SELECT
(VIDEO or RGB) button on the remote to select the
source of the signal to be projected on the screen.
• The selected signal input is displayed at the bottom right of the screen. The
display will show the last selected input source before power was turned off.
RGB 1
Example on-screen display
© 3M 1997
3M™ Multimedia Projector MP8630
11
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 Turn Off the Power
1
1
2
3
1
2
Hold the STANDBY/ON button for 3-5 seconds.
• The ON indicator blinks orange and the lamp turns off.
After approximately 1 minute, the fan stops and the indicator stays orange.
Turn the MAIN POWER switch of the projector off.
Caution: Do not turn off the MAIN POWER switch before pressing the STANDBY/ON button.
After the STANDBY/ON button is pressed, the fan rotates for about 1 minute to cool the
projector.
3
4
Close the lens shutter.
• Push up on the lens cover switch to close.
Disconnect cables.
3M™ Multimedia Projector MP8630
© 3M 1997
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Adjustment and Functions
4.1 Menu
1, 2
2
1
MENU
1
RESET
1
2
3
Press the MENU (
) buttons on
projector or remote control MENU button.
• On-screen menus are displayed on the screen.
Select the menu to be adjusted using the MENU (
STICK SWITCH.
) buttons or
• Selected Menu is highlighted.
Select the item to be adjusted using the MENU (
or STICK SWITCH.
) buttons
• Highlighted items may be adjusted.
Memory function
Individual memory functions are provided for the VIDEO1, VIDEO2, RGB1 and RGB2 input terminals.
Adjustments are saved after power off.
To return to the factory default setting:
√ Highlight SETUP option.
S E T U P I N P U T I M A G E O P T .
VOL
√ To reset the entire SETUP menu
RESET
‘SETUP’
B R I
CON
SHA
COL
T I N
• Press the RESET button.
• Select DEFAULT or CANCEL.
DEFAULT
CANCEL
√ To reset a single item from SETUP menu
• Select the adjustment item (brightness, contrast...)
• Press the RESET button. Only the selected item resets.
© 3M 1997
3M™ Multimedia Projector MP8630
13
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2 How To Use Foot Adjusters
Adjust the projection position using the foot adjusters at the bottom of the projector.
Front view
unlock ←
→ lock
Foot adjusters
Side view
4.2.1
4.2.2
4.2.3
Lift up the projector, unlock the foot adjusters.
Adjust a viewing angle, and then lock the foot adjusters.
For fine adjustments, rotate the foot adjusters.
Caution: Do not unlock the foot adjusters if you do not support the projector.
If the foot adjusters do not lock completely, turn the foot adjusters slightly before locking.
3M™ Multimedia Projector MP8630
© 3M 1997
14
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3 SETUP
The menu SETUP is used to adjust the image and to move the image position.
RGB signal input
Video signal input
Adjustment Item
VOLUME
Details of adjustment
Decrease Increase
BRIGHT
(BRIGHTNESS)
Dark
Bright
CONTRAST
SHARPNESS
COLOR
Lower
Soft
Higher
Sharp
More
Less
Red
TINT
Green
V.POSIT
(V.POSITION)
Moves the picture up or down.
Moves the picture left or right.
H.POSIT
(H.POSITION)
H.PHASE
H.SIZE
Decreases the picture flicker.
Widens or Narrows the horizontal size of picture.
Note:
• TINT cannot be adjusted with a PAL video signal input.
• TINT, COLOR and SHARPNESS cannot be adjusted with an RGB signal input.
• V. POSIT, H. POSIT, H. PHASE and H. SIZE cannot be adjusted with a VIDEO signal input.
© 3M 1997
3M™ Multimedia Projector MP8630
15
Download from Www.Somanuals.com. All Manuals Search And Download.
4.4 INPUT
The menu INPUT is used to select the input source.
S E T U P I N P U T I M A G E O P T .
RGB1
RGB2
VIDEO1
VIDEO2
TEST
PATTERN
Selection
RGB1
Description
Selects the RGB 1 terminal.
RGB2
Selects the RGB 2 terminal.
VIDEO1
Selects the VIDEO 1 terminal.
Selects the VIDEO 2 terminal.
Selects the TEST PATTERN. (Start up screen.)
SYSTEM Selects the video signal systems.
VIDEO2
TEST PATTERN
4.5 IMAGE
The IMAGE menu is used to alter the image.
S E T U P I N P U T I M A G E O P T .
S E T U P I N P U T I M A G E O P T .
M I R R O R
MIRROR
BLANK
REVEAL
DISP. SIZE
MESSAGE
NORMAL
H:INVERT
V :INVERT
H&V:
INVERT
S E T U P I N P U T I M A G E O P T .
S E T U P I N P U T I M A G E O P T .
B L A N K
R E V E A L
WHITE
BLUE
FAST
BLACK
MEDIUM
SLOW
3M™ Multimedia Projector MP8630
© 3M 1997
16
Download from Www.Somanuals.com. All Manuals Search And Download.
4.5 IMAGE (continued)
S E T U P I N P U T I M A G E O P T .
MESSAGE
TURN ON
TURN OFF
Selection
Description
Inverts the picture horizontally or vertically.
H : INVERT Inverts the picture horizontally.
V : INVERT Inverts the picture vertically.
MIRROR
H&V: INVERT Inverts the picture horizontally and vertically.
BLANK
REVEAL
MESSAGE
Selects the blank color.
Selects the speed of revelation.
Turn off the on-screen message.
Display Size
Source
Option
Description
640 X 480
800 X 600
1024 X 768
Normal
Large
Displays in 640x480 window centered on screen.
Expands 640x480 to full 800x600 screen.
Normal
Large
Displays full 800x600.
Not available.
Normal
Large
Compresses 1024x786 to 800x600 screen.
Displays 800x600 "window" into 1024x768. This
window can be moved with H and V Position or by
holding position button and moving the stick switch.
Video
Normal
Large
Displays video in a 640x480 window centered on screen.
Expands video to fill 800x600 screen.
© 3M 1997
3M™ Multimedia Projector MP8630
17
Download from Www.Somanuals.com. All Manuals Search And Download.
4.6 OPT
The meno OPT. allows you to control communication function.
S E T U P I N P U T I M A G E O P T .
COM. SPEED
COM. BITS
TIMER
LANGUAGE
AUTO OFF
STARTUP
S E T U P I N P U T I M A G E O P T .
S E T U P I N P U T I M A G E O P T .
1200
2400
4800
9600
19200
COM. SPEED
(bps)
COM. BITS
7N1
8N1
S E T U P I N P U T I M A G E O P T .
S E T U P I N P U T I M A G E O P T .
ENGLISH
LANGUAGE
FRANCAIS
DEUTSCH
ESPANOL
ITALIANO
NORSK
TIMER
10 min.
NEDERLANDS
S E T U P I N P U T I M A G E O P T .
AUTO OFF
0 min.
STOP
Selection
Description
COM. SPEED Selects the data speed of transmission. (For mouse emulation-1200)
Selects the data format of transmission.
COM. BITS
7N1... 7 data-bits, No parity, 1 stop bit. (For mouse emulation-7NI)
8N1... 8 data-bits, No parity, 1 stop bit.
TIMER
Sets minutes of timer.
Selects the language on-screen menu.
(English, French, German, Spanish, Italian, Swedish, Dutch)
LANGUAGE
AUTO OFF
Selects how long projector will stay on, if no input is detected.
Select 0 to disable this function.
3M™ Multimedia Projector MP8630
© 3M 1997
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Connection to Signal Terminals
5.1 Connection to the Video Signal Terminal
a.
Input signal
Luminance signal
Chrominance signal
1.0Vp-p, 75 Ω termination
S-VIDEO signal
VIDEO signal
0.286Vp-p (burst signal), 75 Ω termination
1.0Vp-p, 75 Ω termination
Input
200mVrms, 20 k Ω below (MAX 3.0Vp-p)
0~200mVrms, 1k Ω
AUDIO signal
Output
b.
Signal input terminal
Chrominance signal
Luminance signal
Ground
Ground
S VIDEO input (Mini DIN4 pin)
Note:
Video input signal terminals have priority in the following order:
1. S-VIDEO input terminal
2. RCA jack (composite) input terminal
5.2 Connection to the RGB Signal Terminal
a.
Input signal / Output signal
Video signal
Analog 0.7Vp-p 75 Ω termination (Positive polarity)
Horizontal sync signal TTL level (Positive/negative polarity)
Vertical sync signal
TTL level (Positive/negative polarity)
Composite sync signal TTL level
Input
200mVrms, 20k Ω below (MAX 3.0Vp-p)
Audio signal
Output 0 ∼ 200mVrms, 1k Ω
b.
Signal input terminal / output terminal
1
2
3
4
5
6
7
8
Video signal (Red)
9
N.C
Video signal (Green) 10 Ground
Video signal (Blue)
N.C
11 Ground
12 N.C
N.C
13 Horizontal/Composite sync signal
14 Vertical sync signal
15 N.C
Ground (for R)
Ground (for G)
Ground (for B)
D-sub 15pin (Male)
© 3M 1997
3M™ Multimedia Projector MP8630
19
Download from Www.Somanuals.com. All Manuals Search And Download.
c.
Example of computer signal
Resolution
fH
(kHz)
fV
(Hz)
Interlaced /
Non-interlaced
Computer/Signal source
Sync Signal
Note
H × V
31.5
31.5
31.5
35.0
37.9
37.9
48.1
49.7
49.1
60.2
H, V separate
H: Positive
V: Negative
VGA-1
Note: 3
Note: 3
Note: 3
Note: 1
Note: 3
640 × 350
640 × 400
640 × 480
640 × 480
640 × 480
800 × 600
800 × 600
832 × 624
1024 × 768
1024 × 768
70.1
70.1
59.9
66.7
72.8
60.3
72.2
74.5
60.1
75.0
Non-interlaced
(IBM™ compatible)
H, V separate
H: Negative
V: Positive
VGA-2
Non-interlaced
Non-interlaced
Non-interlaced
Non-interlaced
Non-interlaced
Non-interlaced
Non-interlaced
Non-interlaced
Non-interlaced
(IBM™ compatible)
H, V separate
H: Negative
V: Negative
VGA-3
(IBM™ compatible)
H, V separate
H: Negative
V: Negative
Macintosh™ 13 inch mode
(Apple™)
H, V separate
H: Negative
V: Negative
VESA 72 Hz standards
H, V separate
H: Positive
V: Positive
SVGA
(VESA 60Hz)
H, V separate
H: Negative
V: Negative
SVGA
(VESA 72Hz)
H, V separate
H: Negative
V: Negative
Macintosh™ 16 inch mode
(Apple™)
Note: 1
Note: 2
Note: 2
H, V separate
H: Positive
V: Positive
XGA
(VESA 60Hz)
H, V separate
H: Positive
V: Positive
XGA
(VESA 75Hz)
Note 1: MAC adapter is necessary to set the resolution mode.
Projector is compatible with 13 inch mode and 16 inch mode.
Set all dip switches OFF except those indicated in the chart.
For example:
MAC 13" mode = switch 1, 5 and 6 are ON
MAC 16" mode = switch 2, 5 and 6 are ON
(Example of 16 inch mode)
Note 2: XGA (1024 x 768) will have less resolution, due to compression techniques used to display the image
Note 3: Some input sources may not be displayed properly because they are not compatible with the projector.
3M™ Multimedia Projector MP8630
© 3M 1997
20
Download from Www.Somanuals.com. All Manuals Search And Download.
5.3 Connection to the Control Signal Terminal
a.
Mouse emulation
(1) While the projector and computer are turned OFF, connect the projector and the mouse terminal of
computer using an appropriate cable. (PS/2, Serial or ADB)
(2) Turn ON the projector.
(3) Turn ON the computer.
(4) Select the correct mouse driver for the application. See computer's User Manual for this procedure.
Note: In some Notebook computers which have internal pointing device, mouse emulation will not work unless
the internal pointing device is disabled. In this case, disable the internal pointing device in BIOS setting.
Check the computer's manual for procedure to follow to disable internal pointing device in BIOS setting.
Caution: Turn off the power to both the projector and computer before connecting.
Connect the computer to the control terminal of the projector using the appropriate cable.
PS/2 mouse
PS/2 port
D-sub 15pin (Female)
ADB mouse
ADB port
D-sub 15pin (Female)
© 3M 1997
3M™ Multimedia Projector MP8630
21
Download from Www.Somanuals.com. All Manuals Search And Download.
5.3 Connection to the Control Signal Terminal (continued)
Serial mouse
(male)
D-sub 15pin (Female)
Serial Mouse cable
b.
RS 232 Control Cable (not included with basic packout)
This cable is used to directly control the projector without using the Remote Control or Operator's Panel.
(male)
RS-232 cable
D-sub 15pin (Female)
3M™ Multimedia Projector MP8630
© 3M 1997
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Maintenance
6.1 Cleaning the Air Filter
Note: Clean the air filter about every 50 hours.
a) Turn off the MAIN POWER switch of the projector and pull out power cord. Let cool for 20 minutes.
b) Remove the air filter from the bottom of projector. Unscrew two retaining screws and pull down and
out on the handle to free air cleaner door. Carefully lift up and out on filter door.
Remove the air filter
c) Clean the air filter using a vacuum cleaner. If dirt is still present, wipe the air filter with a cloth
moistened with water and wipe with a dry lint-free cloth.
d) After filter dries completely, re-install the air filter.
Note: If air flow is restricted due to dust accumulation on filter, the projector may shut down due to over heating.
6.2 Message Table
a) On Screen Display. The following messages are displayed on the screen:
NO SIGNAL IS DETECTED:
The projector is not detecting a signal.
SYNC IS OUT OF RANGE:
The horizontal frequency of the input signal exceeds the range
of the projector, or it cannot be displayed.
CHANGE THE LAMP:
Change when the lamp message appears on the screen.
b) Indicator Display. The ON indicator, LAMP indicator and TEMP indicator will light or blink in the
following cases:
Indicator status
Lights orange
Blinks green
Lights green
Blinks orange
Lights red
Meaning
Standby mode
Remedy
normal
During warming up
During operation
normal
ON indicator
normal
normal
During cooling down
Lamp cannot light
Cool projector by power off for 20 minutes.
Ensure filter is closed.
LAMP indicator
TEMP indicator
Blinks red
Air filter open
Lights red
Temperature inside too high
Cooling fan not operating
Let projector cool 20 minutes. Check air flow and filter.
call your dealer
Blinks red
*When the LAMP indicator lights or blinks, turn the power off. If the problem persists, contact your dealer.
© 3M 1997
3M™ Multimedia Projector MP8630
23
Download from Www.Somanuals.com. All Manuals Search And Download.
6.3 Lamp
The following symptoms may indicate a lamp in need of replacement:
•
•
•
A dark picture.
LAMP indicator lights up red.
"CHANGE THE LAMP" message appears on the screen.
Display Lamp Operation Hours
If the "CHANGE THE LAMP" message appears on the screen or if there is need to determine the lamp
operation hours, follow these steps:
a) While the projector is running, press and hold the timer button on the remote control for 3 seconds.
b) The operating time of the lamp will be displayed.
c) To reset the timer, press the reset button and select 0 (or CANCEL). The "CHANGE THE LAMP"
message will not come up if the timer is reset.
Replacing the Lamp
6.3.1 Remove lamp access door: The lamp access door is located
on the back of the machine on the right side. Use a phillips
screwdriver to unscrew the cover retaining screws and gently
open the cover and set it aside.
Warning: There are high voltage parts inside the cabinet that
may cause an electric shock. Always unplug
projector when changing lamp.
Warning: Lamp and adjacent metal parts become extremely
hot and can cause severe burns to your fingers.
Allow the projector to cool for at least 1 hour
before replacing the lamp.
6.3.2 Retaining screws: Use a standard screwdriver to unscrew
the lamp module retaining screws.
Note: There are three lamp module screws that must be loosened.
These screws are self-containing screws that cannot be
removed from the lamp module.
6.3.3 Remove lamp module: Grasp the lamp module with the one
hand and the projector body opening with the other hand.
Apply upward pressure to the projector body as you slide the
lamp out.
3M™ Multimedia Projector MP8630
© 3M 1997
24
Download from Www.Somanuals.com. All Manuals Search And Download.
6.3.4. Insert lamp module: Carefully insert the new lamp module.
Ensure that it is fully seated.
Tighten the lamp module retaining screws to secure the lamp
module in place.
Insert the hinge tabs on the left side of the lamp access door, then
close and tighten the retaining screws to secure the door
6.4 When You Think Something Is Wrong
Check the following again before asking for service. If a solution cannot be found, consult dealer.
Symptom
Cause
Solution
Power cannot be turned •The Main power is not turned on.
•Turn the MAIN POWER switch on.
•Insert the power cord into an AC socket.
on
•The power cord is disconnected.
No picture and sound
•The setting of the input source is not
correct.
•Set the correct input using the input select button
of the projector or the remote control.
•RGB/Video/Audio wiring to projector is
not correct.
•Connect the cable correctly.
•Connect the cable correctly.
Sound is heard with
no picture
• RGB/Video wiring to projector is not correct.
•The brightness is set fully to dark side.
•Press the MENU button and increase
BRIGHTNESS.
•Audio wiring to projector is not correct.
•The volume is set to minimum.
•The unit is muted.
• Connect the cable correctly.
• Press the VOL button and increase VOLUME.
• Press the MUTE button.
Picture is displayed
with no sound
Color is weak and tint is • The color and tint have been adjusted
• Adjust the color and tint correctly.
incorrect
incorrectly.
Picture is dark
•The brightness and contrast has been
adjusted incorrectly.
•Adjust the brightness and contrast correctly.
•Replace the lamp with a new one.
•The lamp needs to be replaced.
• Projector is out of focus.
Picture is not clear
• Adjust the focus.
LAMP indicator lights
red
• Turn off power and let cool for 20 minutes, then restart.
• If problem persists call your dealer.
• Lamp is too hot.
TEMP indicator lights
red
• Do not block the ventilation holes.
• Clean air filter
• Inside the projector too hot.
LAMP indicator blinks
red
• Air filter door on bottom of case is open.
• Ensure air filter door is closed.
© 3M 1997
3M™ Multimedia Projector MP8630
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Technical Specifications
7.1 Specifications
Note: All specifications are subject to change without notice.
Product name
Model Name
Display system
Multimedia projector
MP8630
3 beam poly-silicon LCD
1.3 inches (33 mm)
TFT active matrix
Panel size
Liquid crystal
panel
Drive system
Number of pixels 519,168 pixels (V624 × H832) per panel. 1.56 million pixels total with 3 panels.
Lens
F/Number: F/2.3 – F/3.0
Metal halide lamp 250W
2W and 2W (stereo)
Focal Length: F = 48.1 – 72.1 mm (1.9" – 2.8")
Lamp
Speaker
Power supply
Power consumption
Usable temperature range
Dimensions
Weight
AC100 ∼ 120V, 5A / AC220 ∼ 240V, 2A (Universal)
350W
32° ∼ 95°F (0° ~ 95°C)
16.3" (W) × 5.9" (H) × 12.0" (D)
414 mm (W) x 150 mm (H) x 305 mm (D)
18 lbs. (8.1 kg)
S VIDEO : Mini DIN4-pin terminal
VIDEO : RCA Jack terminal
AUDIO : RCA Jack terminal
video signal input
terminal
Input/Output
terminal
RGB input/output RGB signal : D-sub 15pin (Female)
signal terminal
AUDIO
: Stereo mini jack
Control terminal
D-sub 15pin (Male)
Part Number
7.2 Accessories
•
•
•
•
•
•
•
•
•
•
•
•
Metal halide lamp module, 250 W
78-8118-3294-4
Power cord (US)
Power cord (UK)
Power cord (Germany)
VGA cable
MAC adapter
S-video cable
3-conductor video/audio cable
Serial mouse cable
PS/2 mouse cable
ADB mouse cable
RS 232 control cable
26-1011-8852-7
78-8118-3304-1
78-8118-3303-3
26-1011-3421-6
78-1011-3308-2
26-1011-3419-0
78-8118-3306-6
78-8118-3315-7
78-8118-3313-2
78-8118-3314-0
78-8118-3312-4 (not included with basic packout)
3M™ Multimedia Projector MP8630
© 3M 1997
26
Download from Www.Somanuals.com. All Manuals Search And Download.
7.3 Dimension Diagram
© 3M 1997
3M™ Multimedia Projector MP8630
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Let us help you make the most of your next presentation. We offer everything from presentation supplies to tips for better meetings. And we're
the only transparency manufacturer that offers a recycling program for your used transparencies. For late-breaking news, handy reference and
free product samples, call us toll-free in the continental United States and Canada from 7:30 a.m. to 5:30 p.m. (CST) or visit our Internet Website.
Printed on 50% recycled wastepaper,
3M Austin Center
3M Canada
3M Mexico, S.A. de C.V.
3M Europe
including 10% post-consumer
Building A145-5N-01
6801 River Place Blvd.
Austin, TX 78726-9000
P.O. Box 5757
London, Ontario
N6A 4T1
Apartado Postal 14-139
Mexico, D.F. 07000
Mexico
Boulevard de l'Oise
95006 Cerge Pontoise Cedex
France
Litho in USA
© 3M 1997 78-6970-7519-6
28
Download from Www.Somanuals.com. All Manuals Search And Download.
|