555-540-702
Issue 1
1989
AT&T System 25
Single-Line Telephone
User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
©1989 AT&T
All Rights Reserved
Printed in USA
TO ORDER COPIES OF THIS DOCUMENT REFER TO DOCUMENT
NUMBER 555-540-702.
Your AT&T sales representative, or
Contact:
Call:
800-432-6600, Monday to Friday between 7:30 am
and 6:00 pm EST.
In Canada call: 800-255-1242, or
Write: AT&T Customer Information Center
2855 North Franklin Road
P.O. Box 19901
Indianapolis, Indiana 46219
Every effort was made to ensure that the information in this document
was complete and accurate at the time of printing. However, this
information is subject to change. This document will be reissued
periodically to incorporate changes.
Single-Line Telephone User Guide
Prepared by the
Technical Publications Group
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
This guide describes the features available to you from AT&T
System 25 through a single-line telephone and provides
instructions for using the features. For your convenience, the
features are arranged in alphabetical order.
Your telephone is ready to use as soon as it is connected to the
System 25. Therefore, as you learn to use the features, you can
make and receive calls with your telephone just as you would
with an ordinary phone.
System 25 supports both touch-tone and rotary sets. However,
if you have a rotary set, you will not be able to use the features
that require you to enter a “*” or “ #” character.
Features
Your AT&T System 25 has two types of features: fixed and
A fixed feature is one that is provided on every
assignable.
single-line telephone. (In this guide, fixed features are indicated
at the beginning of a feature description by a box with a check.)
An assignable feature is not provided automatically. It must be
“assigned” by your System Administrator. (In this guide,
assigned features are indicated at the beginning of a feature
description by an empty box.)
fixed feature
✔
assignable feature
Check with your System Administrator as to which features have
been assigned to you. (As a reminder, you can place a check in
the box of each assignable feature as you receive it.)
1
Download from Www.Somanuals.com. All Manuals Search And Download.
The Switchhook
The switchhook is the button held down by the handset when it
rests in the cradle on your telephone. Some System 25 features
require that you use the switchhook to signal the system.
When you are instructed to press the switchhook, press the
button down as far as it will go for approximately 1/ 2 second and
then release it. If the switchhook is released too soon, the signal
will not work. If you hold the switchhook down for too long
your call will be disconnected.
If you want to hang up and place another call right away, be
sure to hold down the switchhook for more than two seconds.
NOTE: If you have a RECALL or FLASH button on your
telephone, you can press it instead of the switchhook.
The RECALL or FLASH buttons cannot be used to disconnect a
call.
Ringing Tones
System 25 signals you with three distinctive rings. The rings
and their descriptions are listed below.
INSIDE CALL IIIIIIIIIIIIIIIIIIII (one long ring)
Your call is from a person inside your company.
OUTSIDE CALL IIIII IIIII (two short rings)
Your call is from the attendant or someone outside your
company.
PRIORITY RING IIIII IIIII IIIIIIIIII (two short rings and one long ring)
You are being alerted that your request for Callback can now be
completed; or a call is being set up remotely for your phone via
a data feature known as Third-Party Call Setup.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Handset Tones
System 25 signals you with tones that are heard through the
handset. The tones and their descriptions are listed below.
DIAL TONE lllllllllllllllllllllllllllllllllllllllllllllllllIll (a continuous steady tone)
You can dial.
CONFIRMATION TONE II II II (three short tones)
Your action has been accepted.
RINGBACK TONE IIIIIIIIIIIIIII IIIIIIIIIIIIIII (repeating on/ off tone)
The number you dialed is ringing.
SPECIAL RINGBACK TONE IIIIIIIIIIIIIIIII II (one long tone and
one short, dull tone)
The person you dialed is busy, and has been notified of Call
Waiting.
BUSY TONE IIIII IIIII IIIII (repeating on/ off tone)
The number you dialed is busy.
FAST BUSY TONE Ill Ill Ill Ill (fast repeating on/ off tone)
The number you dialed was busy, misdialed, or restricted.
CALL WAITING TONE (short tone(s) heard during a call)
(the waiting call is an inside call)
III
III III (the waiting call is an outside call)
You have a call waiting to be answered.
QUEUEING TONE II II II II II (five short tones)
Your request for a callback has been confirmed.
DEQUEUEING TONE II II II (three short tones)
The extension or outside line that you requested for callback is
now available.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Data Dial Code (DDC)
When your System 25 was installed, Data Dial Codes (DDCSs)
were assigned to data terminals. If you have a data terminal
associated with your System 25, you will receive separate
information regarding its use.
Personal Dial Code (PDC)
Personal Dial Codes (PDCs) were assigned to telephones. In
most cases, your PDC is your extension number. If a telephone
is shared by two or more people, each person may have been
“floating” extension number (FPDC).
assigned their own
Additional Information
See your System Administrator if you have any questions or
would like additional information about your System 25 features.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Single-Line Features
Account Code Entry
For bookkeeping purposes, your System Administrator may
assign account codes to use with certain calls. If you are
required to use account codes for outgoing calls, the account
code must be entered before you can place an outgoing call. If
this feature is not mandatory, you may still use the Account
Code Entry feature.
See your System Administrator to verify the types of calls, if
any, for which you must enter an account code.
Account Code Entry - Outgoing Calls
Listen for dial tone, then press
Dial the account code.
*
0 .
1
❑ ❑
2
NOTE: If you make a mistake while entering the account
code, press again, then the correct account code.“
*
0
❑ ❑
Listen for dial tone.
3
Dial the outside line access code and listen for dial tone
again.
4
Dial the telephone number.
5
(Continued)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Account Code Entry (Continued)
Account Code Entry - Incoming Calls
Your call will be disconnected when you follow this procedure.
Therefore, do not attempt it until you have finished your
conversation.
After you have completed your conversation, and before you
hang up, press the switchhook.
1
Listen for confirmation tone and dial tone.
2
3
4
Dial *
0 .
❑ ❑
Dial the account code.
NOTE: If you make a mistake while entering the account
code, dial *
0 again and then the account code.
❑ ❑
Listen for confirmation tone, then hang up.
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Call Accountability
You can use your own extension number at any other extension
to place toll calls that should be billed to you.
Billing Calls to Your Extension
1 Listen for dial tone, then press #
# .
❑ ❑
2 Dial your extension number.
3 Listen for dial tone, then dial the telephone number.
NOTE: If you make a mistake, hang up and restart the
sequence.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Call Waiting
While you are using your phone, you may be notified through
If you hear one short tone, it
the handset that a call is waiting.
is an inside call waiting for you; two short tones indicate that
you have an outside call waiting.
You must either end the existing call or place it on hold in order
to answer the call waiting.
Answering - Holding the Existing Call
1 Press the switchhook.
2 Listen for confirmation tone and dial tone.
3
Press
*
9 .
❑ ❑
4 Answer the waiting call.
5 After completing the second call, press the switchhook twice
in order to return to the held call.
NOTE: If you hear dial tone,
press the switchhook once more
to return to the call on hold.
Existing Call
Answering - Ending the
1 Hang up.
2 When the telephone rings, lift the handset.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Callback
❑
If a System 25 extension or outside line is busy when you place a
call, you can request a callback. Your call will wait in a line (a
“queue” ) for the extension or line to become available. The
system will then ring you back and complete the call.
For inside calls, use Callback when you hear a busy or special
ringback tone. For outside calls, use Callback only when you
hear a fast busy tone. (You may hear the callback request
queueing tone automatically when you place certain calls.)
Requesting Callback
1 Press the switchhook.
2 After confirmation tone and dial tone, press
#
6
0 .
❑ ❑ ❑
3 Listen for queueing tone, then hang up.
NOTE: If you do not hear queueing tone, your request has
not been accepted for this call.
Completing Callback
1 When you hear priority ring, lift the handset.
NOTE: If you remained off-hook after requesting Callback,
you will not receive priority ring.
2 Listen for dequeueing tone.
Your call will be completed as dialed.
Canceling Callback
1 Lift the handset (or press the switchhook) and listen for dial
tone.
2 Press
#
6
1
and hang up
❑ ❑ ❑
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Conference Calls
You can set up a three-party conference that includes other
System 25 people as well as outside callers. When you are on a
conference call, if you drop the first person you placed in the
conference, you will loose the entire call. (If the first person
hangs up, however, the second person will remain, and the
conversation can be completed. ) You can drop the second
person added to the conference and still continue with your call.
Setting Up Conference Calls
1
Dial the first person.
After the person answers, press the switchhook to put the
call on hold.
2
Listen for confirmation tone and dial tone.
Dial the second person.
3
4
After the second person answers, press the switchhook to
join the calls together.
5
NOTE: If the second person does not answer, press the
switchhook twice to return to the first person. (If you hear
dial tone, press the switchhook once more.)
Dropping the Second Person
1 Press the switchhook.
2 Continue talking with the other person.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct Group Calling (DGC)
❑
Your System Administrator will advise you if you have been
assigned as a member of a Direct Group Calling (DGC) group.
Calls that go to these groups are distributed among its members
for the purpose of answering incoming group associated calls.
Leaving the Group
Members may temporarily not receive incoming calls by use of
the following procedures:
dial tone, then press * 4 .
1 Listen for
2 Listen for
❑ ❑
confirmation tone and hang up.
to the Group
Returning
dial tone, then press
*
4
.
1 Listen for
2 Listen for
❑ ❑
confirmation tone and hang up.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Following
You can have personal calls sent to another phone by using the
Following or the Forwarding feature. To use the Following
feature, at a telephone other than your own, you sign in your
extension number. To cancel the request, you may either sign
out your extension number from that other phone, or sign back
in at your own telephone.
Although Following and Forwarding send your calls to another
telephone, the two features differ slightly. Read the information
and procedures for both, and then use the feature that is
suitable.
Signing In
dial tone, then press * * .
1 Listen for
2 Dial your
3 Dial your
4 Listen for
❑ ❑
own extension number.
extension number again.
confirmation tone, then hang up.
Signing Out
1 Listen for dial tone, then press
2 Dial your extension number.
*
* .
❑ ❑
3 Dial
0 .
❑
4 Listen for confirmation tone, then hang up.
Signing Out All Extensions
This procedure signs out all extension numbers that have been
signed in at this telephone except for the extension normally
assigned to it.
1 Listen for dial tone, then press
*
*
0 .
❑ ❑ ❑
2 Listen for confirmation tone and hang up.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Forwarding
You can have your personal calls sent to another extension or to
an outside number. Unlike the Following feature, you do not
need to be at the other telephone. Instead, simply forward your
calls to another location while you are still at your own
telephone.
Read the information and procedures for both the Forwarding
Then use the feature that best fits your
and Following features.
needs.
NOTE: Your System Administrator may or may not allow your
telephone to forward calls to outside telephone numbers. Check
with your System Administrator for any restrictions you may
have concerning this feature.
Forwarding Calls
1
At your own telephone, dial #
7
0 .
❑ ❑ ❑
Dial the extension number of the other telephone.
2
or
Dial the outside line access code and the phone number of
the outside telephone.
Listen for confirmation tone, then hang up.
3
Canceling Forwarding
1 At your own telephone, press
2 Dial your extension number.
*
* .
❑ ❑
3 Dial your extension number again.
4 Listen for confirmation tone, then hang up.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Hold
You can hold calls while you attend to other matters and then
pick them up again.
After you put a call on hold, you may then
hang up the handset without losing the call. To pick up a call
you have placed on hold you must use the same telephone
where you held the call.
If you want to put a call
extension, you must use
on hold and pick it up from another
the “Park” feature.
Using Hold
1 Press the switchhook.
2 Listen for confirmation tone and dial tone.
3 You may go back to your call by pressing the switchhook
again.
HoId - Placing Another Call
1 Press the switchhook.
2 Listen for confirmation tone and dial tone.
3 Place and complete the second call.
4 To return to the held call, press the switchhook twice. (If
you hear dial tone, press the switchhook once more.)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Leave Word Calling
You can use the Leave Word Calling feature only if the VOICE
POWER Voice Message System (VMS) is connected to your
System 25.
For instructions on obtaining messages left at your telephone,
see your System Administrator.
Leaving Messages
1
Listen for dial tone, then press #
9
2 .
❑ ❑ ❑
2
3
Dial the extension of the other person.
Listen for confirmation tone, then hang up.
NOTE: If you hear fast busy tone instead of confirmation
tone, either the other telephone does not have VMS assigned
to it, or the extension you dialed is invalid.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Message Waiting
Your telephone may have a light that tells you when the
attendant or another person in the system has a message for
you. You can turn the message light on and off at any
telephone in your system that has a message light (including
your own).
Turning On Message Lights
1 Listen for dial tone, then press #
9
0 .
❑ ❑ ❑
2 Dial the extension number of the other telephone.
3 Listen for confirmation tone, then hang up.
NOTE: If you hear fast busy tone instead of confirmation
tone, either the other telephone has no message waiting light
or the extension vou dialed is invalid.
Lights
Turning Off Message
1 Listen for dial tone, then press
#
9
1 .
❑ ❑ ❑
phone where you want the
2 Dial the extension number for the
light turned off.
hang up.
3 Listen for confirmation tone, then
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Night Service
When the attendant leaves for the night, the system can be set
so that incoming calls either ring a night bell or are directed to
See your System Administrator for the
preassigned telephones.
Night Service access code.
Answering Night Service Calls
1 Lift the handset and listen for dial tone.
2 Dial the Night Service access code.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Paging
If your company has a paging system, you may access the
See your System Administrator for
system by dialing a code.
the Paging access code and for additional information if you
have paging zones.
Paging System
Using the
dial tone, then dial the Paging access code.
announcement.
1 Listen for
2 Make the
3 Hang up.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Park
Parked calls are held calls that can be picked up from any
When you use the park feature, you
telephone in the system.
cannot use this feature again on the same phone until the
original parked call is completed. If a parked call is not picked
up within a preset interval (the usual time is two minutes), it
will ring back at the telephone that originally parked the call.
Using Park
1 Press the switchhook and listen for confirmation and dial
tone.
2 Press
*
5 .
❑ ❑
3 Listen for confirmation tone and dial tone.
4 If the call is for someone else, dial or page that person,
notifying them of the Attendant Console or extension
number that parked the call.
press the switchhook
with the caller.
NOTE: If the person does not answer,
twice and complete your conversation
5 Hang up.
Picking Up Parked Calls
1 Listen for dial tone, then press
*
8 .
❑ ❑
2 Dial the extension number that parked the call.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Pickup
Pickup allows you to answer a call that is ringing at another
telephone.
All single-line telephones have this feature. In
addition, your System Administrator may notify you that you
have been assigned to a pickup group. In this case, calls are
picked up differently within your assigned group.
Picking Up Calls
1 Listen for dial tone, then press * 7 .
❑ ❑
2 Dial the extension number of the ringing telephone.
Picking Up Calls in Your Pickup Group
❑
1 Listen for dial tone.
2 Press
*
7
0 .
❑ ❑ ❑
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Placing Calls
You can place calls to people inside and outside your company.
Your System Administrator will give you the required outside
line access code.
Placing Inside Calls
1 Lift the handset and listen for dial tone.
2 Dial the extension number.
Placing Outside Calls
1 Listen for dial tone.
2 Dial the outside line access code and listen for dial tone.
3 Dial the telephone number.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Speed Dialing Codes
You can program telephone numbers, account codes, and
System Speed Dialing codes into your Personal Speed Dialing
codes. System 25 allows you to program strings of numbers and
special characters (maximum of 25 characters) into the dialing
codes.
The first part of this entry describes, with examples, how to use
special characters when programming. The remaining part of
this entry describes how to actually program or remove Personal
Speed Dialing codes.
Special Characters
You may need to use the “*”
and the “ #” when you program
is used as either a 1.5 second pause or as an
numbers. The “*”
actual character. The “#” may be used at the beginning of end-
to-end signaling, at the beginning of a Speed Dialing code, or as
an actual character.
Using * as a Pause
A "*" by itself will produce a 1.5 second pause. For example,
you may want to program a pause between the outside line
access code and the telephone number.
You program: 9*5557023
9 (1.5 second pause) 555-7023
This means:
as a Character
If you want to use the “*” as a
before the “*”.
Using *
character, you must place a “ #”
program 555-2222 followed by a 3
into a a Personal Speed Dialing
For example, you may want to
second pause, a “*”, and 1234,
code.
5552222* * # *1234
5552222 (3 second pause) *1234
You program:
This means:
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Speed Dialing Codes (Continued)
Using # as a Character
“ # " as an actual character, you must place
If you want to use a
two “ # ”s in the programmed number.
For example, you may want to program 555-1111 followed by a
“ # “, and 7777 into a Personal Speed Dialing
1.5 second pause, a
code.
5551111* # # 7777
5551111 (1.5 second pause) #7777
You program:
This means:
Using # with Speed Dialing Codes
When you want to have a Speed Dialing code as part of your
programmed number, you should use a single “ # ” for the code.
For example, you may want to program the System Speed
“ # 100” into a Personal Speed Dialing code.
Dialing code
You program: #100
System Speed Dialing code # 100
This means:
Using #8 to Start End-to-End Signaling
“ #8” in a programmed number, you tell the
When you place a
system to start end-to-end signaling.
For example, you may want to program both a telephone
number (to be dialed first), and an identification code (that
should be transmitted to the far end).
9*5554444** # 812345
9 (1.5 second pause) 5554444
(3 second pause)
You program:
This means:
(start end-to-end signaling) 12345
(Continued)
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming Speed Dialing Codes (Continued)
Programming or Removing Personal
Speed Dialing Codes
1
Listen for dial tone, then press # 4 .
❑ ❑
2
Dial the number you want to program.
or
If you want to remove a number, go to Step 3.
Press “ # “ and a Personal Speed Dialing number (20 - 39).
Listen for confirmation tone, then hang up.
3
4
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Speed Dialing
Speed dialing allows you to dial telephone numbers (or account
“ #” and a 2- or 3-digit code. There are
codes) by simply dialing
two kinds of speed dialing: Personal and System.
Personal Speed Dialing codes are 2-digit numbers that allow you
to program up to twenty personal numbers. These Personal
Speed Dialing codes use the numbers #20 through #39.
System Speed Dialing codes are programmed by your System
Administrator, and are used for numbers that are frequently
called by people in your company. System Speed Dialing codes
use the numbers # 100 through # 189.
For instructions on how to program Personal Speed Dialing
Placing Calls
1 Listen for dial tone.
2 Dial the #, followed by the speed dialing code (20 through 39
or 100 through 189).
should be transmitted to the far end).
9*5554444** # 812345
9 (1.5 second pause) 5554444
(3 second pause)
You program:
This means:
(start end-to-end signaling) 12345
(Continued)
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Transfer
You can easily transfer calls to another System 25 telephone.
However, you
You can also transfer some calls to outside lines.
should see your System Administrator for more information
about this type of transfer.
When you transfer a call, the original person is temporarily
placed on hold and is not connected to the other person until
you hang up. At that time, the call disappears from your
telephone.
Transferring Calls
1 Press the switchhook.
tone and dial tone.
extension.
2 Listen for confirmation
3 Dial the other person’s
NOTE: If you misdial the number, return to the person on
hold by pressing the switchhook twice. (If you hear dial
tone, press the switchhook once more.) Then return to
Step 2 and continue.
4 Hang up if you do not want to announce the call.
Otherwise, announce the call and then hang up to complete
the transfer.
the person you attempt to call does not answer,
switchhook twice to return to the call on hold. (If
dial tone, press the switchhook once again.)
NOTE: If
press the
you hear
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
feature that allows you to assign account
account code
entry
codes to calls in order to charge them to
specific customers, clients, or business
cases. This feature may be optional or
mandatory.
optional feature that can be assigned to
your telephone by the System
Administrator.
assigned feature
attendant
answers and directs calls
person who
coming into
may or may
Your system
your company.
not have an attendant.
feature that allows you to make calls at
another telephone and charge them to your
extension.
call
accountability
feature that allows you to be notified of an
incoming call while you are on another call.
call waiting
callback
feature that allows you to request
notification of when a busy extension or
outside line is available, and the call is then
completed for you.
feature that allows you to have three parties
on a call at the same time.
conferencing
three short tones indicating that an
action was accepted and you can proceed.
confirmation
tone
feature that allows individuals to have their
calls answered by someone else.
coverage
(Direct Group Calling) group of telephones
to which incoming calls are distributed
among the group members.
DGC
27
Download from Www.Somanuals.com. All Manuals Search And Download.
three short tones indicating that the call for
which you requested Callback can now be
completed.
dequeueing tone
FPD C
(Floating Personal Dial Code) an extension
number associated with a person, but not a
This feature provides
particular telephone.
the convenience of receiving calls at any
available telephone.
repeating on/ off tone indicating that the
dialed number or access code was busy,
restricted, misdialed, or the trunk group
was busy.
fast busy tone
sequence of characters (digits, “*”, or “ # “)
that allows you to access System 25
features.
feature access
code
standard feature that is available to every
telephone.
fixed feature
features that allow you to redirect your
incoming calls to another telephone.
following
forwarding
feature that temporarily suspends a call.
hold
call between two or more System 25
inside call
It is signalled by one long ring.
telephones.
feature that allows you to notify a person at
a
busy or unanswered telephone that you
have called. To use this feature, there must
be a VOICE POWER Voice Message System
connected to your System 25.
leave word
calling
feature that allows you to turn on and off
the message light on telephones in the
system.
message waiting
feature that allows you to answer calls
when the attendant is not available.
night service
off-hook
a telephone is off-hook when the handset
has been removed from its cradle, releasing
the switchhook button.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
a telephone is on-hook when the handset is
in its cradle, depressing the switchhook
button.
on-hook
outside call
call between a System 25 telephone and a
telephone not connected to System 25.
Outside calls are made over Central Office
or other trunks and are signalled by two
short rings.
outside line
PDC
a trunk (line) to the Central Office or other
system. Outside lines may be accessed by
dialing an access code.
(Personal Dial Code) extension number that
is assigned to an individual, and is normally
associated with the telephone at the
individual’s desk.
feature that allows you to access paging
equipment from System 25 telephones.
paging
park
feature like hold except that it allows you
answer the call from any telephone.
to
feature that allows you to answer a call that
is ringing at another telephone.
pickup
program
ability to store a telephone number or
account code so you can access it by dialing
a code.
queueing tone
recall
five short tones indicating that your request
for callback has been confirmed.
button on some telephones that may be
pressed instead of the switchhook.
ringback tone
repeating on/ off tone indicating that the
number you dialed is ringing.
special ringback
tone
one long tone followed by one short, dull
tone indicating that the person you dialed is
busy and has Call Waiting.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
feature that allows you to place a call or
enter an account code by dialing “ #” and a
speed dialing
Individual telephones
2- or 3-digit code.
may be assigned 2-digit Personal Speed
Dialing codes, which you can program. All
3-digit System Speed Dialing codes are
assigned by the System Administrator and
can be used at all telephones.
button depressed by the handset when the
telephone is not in use.
switchhook
person responsible for assigning features
and overseeing System 25 operation.
system
administrator
feature that allows you to connect the
person you are talking with to another
person, then drop out of the conversation.
transfer
a telecommunications channel between two
trunk
30
Download from Www.Somanuals.com. All Manuals Search And Download.
AT&T System 25
QUICK REFERENCE CARD
Single-Line Telephone
FEATURE ACCESS CODES
I
CODE
* 0 Code
DESCRIPTION
FEATURE
1
I
Account Code
to enter an Account Code
## Ext.
#60
to charge call to correct extension
to request callback for a busy ext./line
to cancel callback
Call Accountability
Callback
#61
,
* 9
to answer call waiting
Call Waiting
* 4
to leave your DGC group
to return to your DGC group
to sign in extension
Direct Group Calling
* 6
** Ext. Ext.
I
Following
** Ext. O
to sign out extension
(at another extension) t
I
I
“
* *
0
to sign out all extensions
#70 Ext.
to send your calls to another extension
to send your calls to a remote number
to cancel forwarding
Forwarding
#70 number
** Ext. Ext.
(from your extension)
#92 Ext.
to leave message
Leave Word Calling
Message Waiting
#90 Ext.
to turn on message light
#91 Ext.
to turn off message light
* 5
to parka call
Park
* 8 Ext. that parked call
to answer a parked call
* 7 0
to pickup call ringing in your group
to pick up call ringing outside group
to program a Personal Speed Dialing code
Pickup
* 7 Ext.
m
Programming
Speed Dialing
I
to dial a programmed number
(20-39, 100-189)
Code
I
(See Dial Code list on other side.)
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK REFERENCE CARD
Single-Line Telephone
PERSONAL SPEED DIALING NUMBERS
CODE
SYSTEM SPEED DIALING NUMBERS
TELEPHONE NUMBER
CODE
USE
#20
#21
#22
#23
#24
#25
#26
#27
#28
#29
#30
#31
,
,
,
FACILITY ACCESS CODES
CODE
USE
#32
#33
#34
#35
#36
#37
#36
#39
DIALING CODES
ACCOUNT CODES
DESCRIPTION
Your Extension
C O D E
USE
C O D E
I
I
Your Data Terminal
Attendant
Night Service access code
Paging access code
(See Features list on other side.)
Download from Www.Somanuals.com. All Manuals Search And Download.
|
