3Com Switch 4007R User Manual

Quick Installation Guide  
For the 3Com Switch 4007R 8-slot Chassis  
Part No. 10014099  
Published February 2002  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Quick Installation Guide  
For the 3Com Switch 4007R 8-slot Chassis  
Read this document before you attempt to install the 3Com Switch  
4007R 8-slot chassis. This guide includes the following:  
Switch Setup Tasks  
Unpacking Instructions  
Preinstallation Guidelines  
Installing the Mounting Shelves  
Installing the Chassis  
Switch 4007R Kits  
The Switch 4007R is available as a starter kit as described below:  
3Com Gigabit Layer 2 Starter Kit (3C16817)  
8-slot chassis (3C16804)  
820W AC Power Supply (3CB9EP8)  
Management Module (3CB9EME)  
24-Gigabit Ethernet Fabric (3CB9FG24T)  
2 of 9-port 1000BASE-SX Module (3CB9LG9MC)  
3Com Gigabit Layer 3 Starter Kit (3C16818)  
8-slot chassis (3C16804)  
820W AC Power Supply (3CB9EP8)  
Management Module (3CB9EME)  
24-Gigabit Ethernet Fabric (3CB9FG24T)  
9-port 1000BASE-SX Module (3CB9LG9MC)  
4-port Gigabit Multilayer Switch Module (GBIC) (3CB9RG4)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2
Quick Installation Guide  
This guide is intended for the system or network administrator who is  
responsible for installing and managing the network hardware.  
WARNING: The Switch 4007R chassis must be installed, removed, or  
replaced only by trained service personnel. Do not attempt to install,  
remove, or replace a Switch 4007R chassis if you have not had the proper  
training from 3Com.  
WARNING: You can install the Switch 4007R chassis on a table, a shelf,  
or a rack. To minimize the risk of personal injury or equipment damage,  
3Com recommends that at least two people perform an installation.  
Figure 1 3Com Switch 4007R 8-slot Chassis  
Switch fabric  
module slots  
Interface  
module slots  
Management  
module slots  
R
Switch  
4007  
1
2
3
4
5
6
7
8
9
10  
ON  
Power supply slots  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Quick Installation Guide  
3
Switch Setup Tasks Figure 2 illustrates the tasks to perform to set up a Switch 4007R 8-slot  
chassis.  
Figure 2 Setup Tasks for Switch 4007R 8-slot Chassis  
Determine Site Requirements  
• Enterprise Switch Getting Started  
Guide, Appendix B  
Administer and Operate  
the Switch  
Unpack the Switch 4007  
Chassis  
1
• “Unpacking Instructions”  
(On the shipping box and  
in this guide)  
• Enterprise Management Engine  
User Guide, Chapter 4 and  
Chapter 5  
12  
2
Troubleshoot Problems  
• Enterprise Management Engine  
User Guide, Chapter 8  
Install the Universal Mounting  
Shelf (for a rack installation)  
Quick Installation Guide for  
the 8-slot Chassis (this guide)  
Switch 4007  
1
2
3
4
5
6
7
8
9
10  
11  
3
4
5
Configure the Switch for  
Management  
• Enterprise Management Engine  
User Guide, Chapter 4 and  
Chapter 5  
Install the Chassis and  
Optional Devices  
Quick Installation Guide for  
the 8-slot Chassis (this guide)  
10  
ON  
Power On the Switch  
• Enterprise Switch Getting Started  
Guide, Chapter 5  
Install a Power Supply and  
the Power Cable  
• Power Supply Installation Guide  
Switch 4007 8-slot Chassis  
for the 8-slot Chassis  
9
Install Interface Modules  
• Interface module quick start or  
getting started guides  
• Interface module user guides  
(if available)  
Install an EME Management  
Module  
• Enterprise Management Engine  
Quick Start Guide  
• Enterprise Management Engine  
User Guide  
8
6
Install a Switch Fabric  
Module  
• Switch fabric module quick  
start or getting started guides  
• Switch fabric module  
user guides (if available)  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
4
Quick Installation Guide  
Unpacking Follow these steps:  
Instructions  
1 Place the chassis shipping box near the rack, the table, or the shelf where  
you plan to install the chassis.  
WARNING: Safety regulations state that the selected table, shelf, or rack  
must be able to support at least three times the weight of a fully loaded  
chassis.  
A fully loaded 8-slot chassis weighs approximately 71.7 kg (158 lb).  
Therefore, the selected table, shelf, or rack must support at least  
215.1 kg (474 lb).  
2 Cut the tape that covers the seam on the top of the box.  
3 Remove the following items (Figure 3) from the top of the shipping box:  
One hardware kit in a plastic bag (Part Number 10002489 16SL HDW)  
Four plastic feet to mount to the bottom of the chassis (for a  
tabletop installation)  
Four 6-32 Phillips-head screws to mount the feet  
Twelve rack-mount clips for a rack-mount installation  
Twelve 10-32 Phillips-head screws to attach the chassis to the rack  
One plastic label bezel to snap into the top front of the 8-slot chassis  
NOTE: To prevent the plastic label bezel from being damaged, do not  
attach it to the chassis until after you have installed all components into  
the chassis and you are ready to power on the Switch.  
Two universal mounting shelves (brackets)  
One documentation kit that contains:  
Documentation CD-ROM  
Chassis Quick Installation Guide for the Switch 4007R 8-slot  
Chassis  
Switch 4007R Getting Started Guide  
Switch 4007 Web Management User Guide  
Power Supply Installation Guide for the Switch 4007R  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Quick Installation Guide  
5
Figure 3 Contents of the Switch 4007R Chassis Shipping Box  
Chassis Top  
Chassis rack-mount template  
Plastic label bezel  
Switch  
4007  
Pre-installed  
pin  
2 Mounting shelves  
Documentation  
CD-ROM  
Plastic feet  
6-32 screws  
10-32 screws  
Rack-mount clips  
Pre-installed  
pin  
1000XXXX  
HARD  
W
ARE KIT  
Mounting  
shelf  
Chassis Bottom  
Plastic bag for  
hardware kit  
Rack hole  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
6
Quick Installation Guide  
4 Remove the top foam packing material (Figure 4).  
Figure 4 Removing the Chassis Shipping Box  
Top foam  
packing material  
Corrugated sleeve  
Bottom foam  
packing material  
Shipping skid  
5 On the outside of the shipping box on the skid, cut the shipping bands.  
6 Remove the corrugated sleeve by pulling it straight up (Figure 4).  
The 8-slot chassis is shipped with module slot 1, slot 7; management  
module slot 9 empty. No blank faceplate covers these slots. See Figure 5.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Quick Installation Guide  
7
Figure 5 The Switch 4007R 8-slot Chassis is Shipped with These Slots Empty  
Switch fabric  
module slot 7  
Interface  
module  
slot 1  
Management  
module slot 9  
Switch  
4007  
1
2
3
4
5
6
7
8
9
10  
Power supply slots  
After you receive the chassis, remove the faceplate from power supply  
slot 3 to help make chassis installation easier. See step 8 in this section.  
7 While the 8-slot chassis is still in the base of the shipping box, have one  
person grasp the chassis and tilt the chassis backward.  
8 To make chassis installation easier, remove another blank faceplate from a  
power supply slot.While the 8-slot chassis is in this position, and using a  
flat-blade screwdriver, remove the blank faceplate from power supply slot  
3 only.  
9 Using two people, lift the Switch 4007R 8-slot chassis out of the shipping  
box base and place the chassis on the floor in front of the rack, table, or  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
8
Quick Installation Guide  
shelf that you plan to use. To help you hold onto the 8-slot chassis when  
you lift it, you can place one hand into the empty power supply slot 3.  
The other person places one hand into empty power supply slot 1.  
10 Inspect the chassis for damage. If the chassis appears to be damaged,  
repack it in the shipping box and contact your local supplier.  
The shipping box is reusable; place all packing materials in the chassis  
shipping box and store the shipping box for future use.  
Preinstallation This section provides safety precautions, installation guidelines, and  
Guidelines location requirements to help you install the Switch 4007R 8-slot chassis  
into your environment.  
Safety Precautions  
Read this section before you install the Switch 4007R 8-slot chassis.  
WARNING: The rack-mount installation requires at least two people. Do  
not attempt to install the chassis alone. To reduce the possibility of  
personal injury or serious damage to the chassis when you install the  
chassis into a rack, first install the mounting shelves that are shipped with  
your chassis. The mounting shelves help hold the chassis in place while  
you secure the chassis to the rack. Rest the chassis on the mounting  
shelves and continue to support the chassis until after you have securely  
installed at least four of the eight screws (two screws per rack-mount  
flange) for the chassis.  
If you do not use the mounting shelves and then you attempt to place the  
weight of the rack-mounted chassis on fewer than four fully installed  
screws, the chassis may drop off of the rack. Personal injury or serious  
damage to the chassis may result. The tabletop or shelf installation also  
requires at least two people to lift the chassis onto the table or shelf.  
WARNING: The chassis has two stationary, preinstalled flange pins  
located in the Telco rack slot. Use these flange pins only to help position  
the chassis. Do not use these pins to support the full weight of the  
chassis.  
WARNING: When the Switch 4007R 8-slot chassis is fully loaded with  
modules and load-sharing power supplies, the chassis weighs  
approximately 71.7 kg (158 lb). Therefore, for a rack installation, install  
the mounting shelves and then your 8-slot chassis before you install  
modules and power supplies.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Quick Installation Guide  
9
WARNING: Safety regulations state that the selected table, shelf, or rack  
must be able to support at least three times the weight of a fully loaded  
chassis.  
A fully loaded 8-slot chassis weighs approximately 71.7 kg (158 lb).  
Therefore, the selected table, shelf, or rack must support at least  
215.1 kg (474 lb).  
WARNING: To ensure mechanical stability and to avoid circuit  
overloading and improper grounding, follow the rack manufacturer’s  
instructions for rack installation. If the instructions are unclear, consult a  
qualified electrician.  
Location Requirements  
Install a Switch 4007R 8-slot chassis in an area that meets the following  
requirements:  
Ambient (room) temperature is from 0 °C to 50 °C (32 °F to 122 °F).  
Relative humidity is between 10 and 90 percent, noncondensing.  
The table, shelf, or rack on which you mount the chassis supports at  
least three times the weight of a fully loaded chassis.  
There is at least 91.4 cm (36 in.) in back of the chassis to remove and  
replace fan trays and to ensure proper cooling in the chassis.  
The power source is within approximately 2 meters (6.6 feet) of the  
location where you plan to install the Switch 4007R.  
Each of the power supplies connects to a dedicated socket. Do not  
connect the power supplies to a power strip.  
For a tabletop or shelf installation, the surface on which you want to  
locate the Switch 4007R chassis is level.  
For rack installations, the selected rack is grounded in accordance with  
the rack manufacturers recommendations.  
Before You Begin  
Before you install the 8-slot chassis:  
Move the Switch 4007R chassis close to where you plan to install it.  
Place the chassis in front of the rack, table, or shelf that you plan to  
use.  
For a rack installation, make certain that you have a Phillips  
screwdriver and a flat-blade screwdriver, the two mounting shelves,  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
Quick Installation Guide  
and the 12 screws (from the hardware kit) available when you begin  
to install the chassis.  
For a tabletop or shelf installation, make certain that you have a  
Phillips screwdriver or flat-blade screwdriver and the hardware kit  
available.  
Before you attempt to mount the chassis in a rack, use the following  
rack-mount installation guidelines to ensure your safety and optimal  
performance. Review the guidelines before you install the chassis in a  
rack.  
Because the equipment rack environment can cause increased  
ambient temperatures and reduced air flow, review the chassis  
specifications and site requirements in Appendix A and Appendix B of  
the Switch 4007R Getting Started Guide.  
Figure 6 shows two types of racks that you can use.  
Figure 6 Rack Types  
1 Bolt the rack to the floor.  
2 Brace the top of the rack against the wall. Make certain that the rack is  
properly aligned and squared. Use a framing tool to ensure that the rack  
is squared.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Quick Installation Guide  
11  
3 To help support the chassis while you install it in a rack, install the  
mounting shelves that are shipped with your chassis. If you install more  
than one chassis in a rack, install the bottom chassis first. Make certain  
that there is sufficient space between the bottom chassis and the top  
chassis to provide space for an optional cable management device.  
4 Position the rack-mount clips if you are going to use them for the  
rack-mount installation. If you install the chassis in Metric rack slots,  
install the clip nuts and screws in the closed slots of the rack-mount  
flanges. If you install the chassis in Telco rack slots, position the chassis  
and then install the screws and rack-mount clips in the open slots.  
If you want to use an optional cable management device, install it above  
or below the chassis (depending on which type of device you choose).  
You can install the chassis in the rack either before or after you install a  
cable management device.  
Use the following guidelines to tighten screws to Torque Specification:  
Faceplate thumbscrews — 5-7 in/lb (inch-pounds)  
#10 screws for holding the chassis and mounting shelves onto the  
rack rail — 22-25 in/lb  
To ensure that you tighten screws to Torque Specification, use a torque  
screwdriver.  
Selecting the Slot on the Rack  
The 8-slot chassis have two slot types on the rack-mount flanges to  
mount the chassis in a rack. Figure 7 shows the Telco and Metric slots and  
the location of the preinstalled rack-mount flange on the 8-slot chassis.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
Quick Installation Guide  
Figure 7 Preinstalled Rack-mount Flange Location and Slot Types on the Switch  
4007R 8-slot Chassis  
Switch 4007  
Preinstalled  
flange pin  
Telco rack  
open slot  
Metric rack  
closed slot  
Using the Chassis Rack-mount Template  
Use the paper rack-mount chassis template (which is an accurate copy of  
the chassis rack-mount flange) to help you position the mounting shelves  
and the Switch 4007R chassis when you install them into a rack. See  
Figure 2. The chassis rack-mount template is designed for use with:  
Racks that have rack slot hole distances as shown in Figure 8. Your  
rack can have either round or square rack slot holes.  
Telco (open) rack slots.  
Installing the The 8-slot chassis are shipped with two mounting shelves and screws.  
Mounting Shelves Install one mounting shelf on each side of the rack. The top slot on the  
mounting shelf is equipped with an alignment pin to help you insert and  
position the mounting shelf in the rack.  
CAUTION: On some racks, the mounting shelf may not align easily to  
install the two mounting shelf screws. One screw per mounting shelf can  
support an empty chassis. However, make certain to secure the chassis to  
the rack before you add any other components.  
The use of clip nuts is optional.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Quick Installation Guide  
13  
To install the mounting shelves, follow these steps:  
1 Obtain the chassis rack-mount template, two mounting shelves, four  
screws, and four clip nuts (optional) that you received in the shipping box.  
2 Locate where you want to install the mounting shelves.  
a While you hold the chassis rack-mount template in place, locate the  
slots on each rack rail to mount the shelves.  
b Mark the desired positions on the rack.  
The rack has a series of paired and single slots that are positioned with  
specific distances between each slot (Figure 8).  
Figure 8 Slots on the Rack and Distances Between Each Slot  
Alignment pin  
position  
1/2"  
5/8"  
5/8"  
Paired slot  
Single slot  
1/2"  
5/8"  
5/8"  
1/2"  
5/8"  
5/8"  
1/2"  
3 Insert a mounting shelf in the rack.  
a Select the desired rack slot position, using the top slot of a pair of slots  
for the mounting shelf alignment pin (Figure 9).  
b Slide the two clip nuts onto the selected rack slot position (optional).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
14  
Quick Installation Guide  
c Insert the alignment pin (Figure 9) into the rack slot.  
If the rack you are using to install the chassis is not threaded, apply  
pressure and push up on the mounting shelf to align the hole properly  
with the rack slot hole. The alignment pin on the mounting shelf will then  
insert easily into the rack.  
4 Using a Phillips screwdriver or flat-blade screwdriver, insert the two  
screws and tighten (Figure 9).  
Figure 9 Installing a Mounting Shelf into the Rack  
Rack  
Preinstalled  
alignment pin  
Preinstalled  
alignment pin  
Screws  
Mounting  
shelf  
5 Repeat steps 3 and 4 to mount the other shelf on the opposite rack rail.  
Make certain that the mounting shelf is aligned to the same rack slot  
positions on both sides of the rack.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Quick Installation Guide  
15  
Installing the Chassis This section describes how to install the chassis:  
In a rack without clip nuts  
In a rack with clip nuts  
On a table or a shelf  
You may have other types of racks at your site. Follow the manufacturer’s  
suggested installation procedures.  
Before you begin, examine the rack to determine if you need to use clip  
nuts in this installation.  
Installing the Chassis in a Rack Without Clip Nuts  
Follow these steps to mount the 8-slot chassis in a rack. Use at least two  
people to perform this installation.  
You have already installed the mounting shelves into the rack and you  
have the rack-mount screws and a Phillips screwdriver or flat-blade  
screwdriver available.  
To prevent the plastic label bezel from being damaged, do not attach it to  
the chassis until after you have installed all components into the chassis  
and you are ready to power on the Switch.  
1 Obtain the chassis rack-mount template that you received in the shipping  
box.  
2 Align the template to match the slots of one of the mounting shelves.  
3 While you hold the template in place, locate the holes on the rack where  
you want to place the chassis. Make certain that the holes on the  
template match up with the rack slot holes.  
4 Locate and mark the holes on the rack, at the top and the bottom where  
you want to place the chassis and the screws.  
5 Prepare to lift the chassis.  
a Standing on one side of the chassis, one person places a left hand in  
power supply slot 3 and with the right hand grasps the handle at the  
top rear of the chassis.  
b The other person, who is standing on the opposite side of the chassis,  
places a right hand in power supply slot 1 and with the left hand  
grasps the handle on the top rear of the chassis.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
16  
Quick Installation Guide  
6 Two people lift the chassis through the front of the rack and onto the  
mounting shelves. Continue to support the chassis until after you have  
securely installed at least four of the eight screws (two screws per  
rack-mount flange) for the chassis.  
7 Slide the chassis into the rack, using the mounting shelves for support,  
until both rack-mount flanges are flush with the front of the rack.  
Use the preinstalled flange pins in the Telco rack slot to position the  
chassis at the desired slot position in the rack.  
WARNING: Support the back of the chassis until the two bottom screws  
are fully inserted.  
8 While the chassis rests on the mounting shelves and you support the  
chassis, insert one bottom screw on each side of the chassis and then  
tighten the screw.  
Tighten the #10 screws that hold the chassis onto the rail to a Torque  
Specification of 22-25 in/lb (inch-pounds).  
9 Insert one top screw on each side of the chassis and then tighten the  
screw.  
10 Install all remaining screws and tighten them.  
11 Attach the plastic label bezel to the 8-slot chassis.  
a With both hands, grasp the plastic label bezel and face the front of  
the chassis.  
b Snap the plastic label bezel onto the top front of the chassis to secure  
it.  
Installing the Chassis in a Rack Using Rack-Mount Clip Nuts  
Follow these steps to mount the chassis in a rack when you use  
rack-mount clip nuts.  
Not all racks require that you use rack-mount clips. Use whatever method  
of rack-mount equipment that you have to meet installation  
requirements in a rack.  
Use at least two people to perform this installation.  
You have already installed the mounting shelves into the rack and you  
have the clip nuts with rack-mount screws and a Phillips screwdriver or  
flat-blade screwdriver available.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Quick Installation Guide  
17  
To prevent the plastic label bezel from being damaged, do not attach it to  
the chassis until after you have installed all components into the chassis  
and you are ready to power on the Switch.  
1 Obtain the chassis rack-mount template that you received in the shipping  
box.  
2 Align the template to match the slots of one of the mounting shelves.  
3 While you hold the template in place, locate the holes on the rack where  
you want to place the clip nuts. Make certain that the holes on the  
template match up with the rack slot holes.  
4 Mark the holes on the rack, at the top and the bottom where you want  
to place the clip nuts and the screws.  
5 Install the clip nuts on the rack in the positions that you selected. See  
Figure 10.  
The rack slots are not equally spaced, so align the clip nuts to the slots  
properly for the screws to be easily installed.  
Figure 10 Installing a Rack-mount Clip in the Rack  
Rack rail  
10-32 inch screw  
Be sure to thread the screw  
through this nut to securely  
attach each clip to the rack  
Top view  
6 Slide the chassis into the rack, using the mounting shelves for support,  
until both chassis rack-mount flanges are up against the rack. Push until  
the chassis rack-mount flanges are flush with the rack.  
7 Using the preinstalled flange pins for guidance, match the slots on the  
rack-mount flange to each clip nut on the rack.  
WARNING: Support the back of the chassis until the two bottom screws  
are fully inserted.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
18  
Quick Installation Guide  
8 Secure the chassis to the rack with the screws provided (eight 10-32 inch  
screws) and with the rack-mount clips.  
a Install one screw on each side in the bottom slot on each rack-mount  
flange.  
b Allow the weight of the chassis to rest on the mounting shelves and  
install the remaining screws while you continue to support the chassis.  
c Tighten all screws completely.  
Tighten the #10 screws that hold the chassis onto the rail to a Torque  
Specification of 22-25 in/lb (inch-pounds).  
9 Attach the plastic label bezel to the chassis.  
a With both hands, grasp the plastic label bezel and face the front of  
the chassis.  
b Snap the plastic label bezel onto the top front of the chassis to secure  
it.  
Installing the Chassis on a Table or Shelf  
This section describes how to attach plastic feet to the chassis and how to  
install the chassis on a table or a shelf.  
WARNING: When you install the chassis on a table or shelf, do not use  
the optional cable management device. The chassis can tip over under  
certain conditions. Hardware damage or personal injury can result.  
WARNING: Safety regulations state that the selected table or shelf must  
be able to support at least 215.1 kg (474 lb), which is three times the  
weight of a fully loaded 8-slot chassis.  
Attaching the Chassis Feet To install plastic, molded feet on the  
Switch 4007R chassis, follow these steps:  
1 Using at least two people, prepare to lift the chassis onto the table or  
shelf.  
a Standing on one side of the chassis, one person places a left hand in  
power supply slot 3 and with the right hand grasps the handle at the  
top rear of the chassis.  
b The other person, who is standing on the opposite side of the chassis,  
places a right hand in power supply slot 1 and with the left hand  
grasps the handle on the top rear of the chassis.  
2 Two people lift the chassis onto the table or shelf.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Quick Installation Guide  
19  
3 Position the chassis on its side so that you can access the bottom of the  
chassis.  
4 Remove the four feet and the four screws from the hardware kit.  
5 Using a flat-blade screwdriver, screw the feet to the bottom of the  
chassis. See Figure 11.  
Figure 11 Attaching Plastic Feet to the Switch 4007R Chassis  
Installing the Chassis on a Table or Shelf To install the chassis on a  
table or on a shelf, follow these steps:  
1 Using at least two people, lift and turn the chassis upright on its installed  
plastic feet.  
2 Position the chassis on the table or shelf so that the chassis rests upright  
squarely on the table or on the shelf (on all four feet).  
3 Ensure that the front and the rear of the chassis are unobstructed and  
easy to reach.  
CAUTION: To prevent the plastic label bezel from being damaged, do not  
attach it to the chassis until after you have installed all components into  
the chassis and you are ready to power on the Switch.  
4 Attach the plastic label bezel to the chassis.  
a With both hands, grasp the plastic label bezel and face the front of  
the chassis.  
b Snap the plastic label bezel onto the top front of the chassis to secure  
it.  
Where to Go from To get your Switch 4007R and its components installed and configured so  
Here that you can connect it to your network, follow the setup tasks shown in  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
20  
Quick Installation Guide  
Figure 2. If you need more details about each setup task, see the  
indicated Switch 4007R documents.  
Locating 3Com The Switch 4007R Getting Started Guide is available in Adobe Acrobat  
User Documentation Portable Document Format (PDF) format on the Switch 4007R  
Documentation CD-ROM.  
The CD-ROM also contains:  
Additional Switch 4007R documents in Adobe Acrobat format  
Adobe Acrobat Reader and Reader installation instructions  
If you have difficulty installing the Acrobat Reader, use an Internet  
browser to download the reader from the Adobe home page at:  
You can view additional 3Com technical documentation on the 3Com  
home page at:  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Accton Technology Switch 12i User Manual
Acer Computer Monitor UMIV6AAA02 User Manual
Acnodes Personal Computer PC 8150 User Manual
Advantech Computer Hardware Intel User Manual
Allied Telesis Network Router Routers and Switches User Manual
Allied Telesis Switch AT GS900 16 V2 User Manual
American Standard Indoor Furnishings M968566 User Manual
Apple Network Cables EtherTalk Adapter User Manual
Audiovox Car Stereo System ACC 50A User Manual
Badger Basket Compact Excavator 460 User Manual